CFF PRO SERIES ELITE HD SQUAT STANDS Assembly & Care Instructions 

 

THANK YOU! First of all, thank you for purchasing the only                 bolt­together squat stands on the market capable of               handling this kind of weight. Before you go throwing                 800­1200lbs at these things, please review these             instructions to ensure your stands are correctly             assembled and last.  

INCLUDED IN THIS DOCUMENT  

● exploded drawing & parts list ● assembly steps ● SPECIAL PRECAUTIONS ● care for your squat stands 

  

EXPLODED DRAWING & PARTS LIST  PLEASE MAKE SURE YOU HAVE ALL THE PIECES!  

 

_ V.04.14.2015 

1 

 

No. Description Qty No. Description Qty

1  Rear Base Frame  2  19  Rubber Bumper  4 

2  Front Base Frame  2  20  PU Wheel  4 

3  Top Upright  2  21  End Cap  4 

4  Spotter Arm  2  22  Plastic Sleeve  2 

5­8  Pin Set  2  23  Tag  2 

9  Bar Holder  2  24  Allen Bolt, M6x12mm  44 

10  Protecting Plastic, 95x40mm  4  25  Flat Washer, M8  10 

11  Protecting Plastic, 95x40mm  4  26  Flat Washer, M12  8 

12  Protecting Plastic, 50x40mm  4  27  Nylon Nut, M8  4 

13  Protecting Plastic, 24x38mm  2  28  Nylon Nut, M12  4 

14  Protecting Plastic, 158x38mm  2  29  Allen Bolt, M12x125mm  4 

15  Protecting Plastic, 84x38mm  2  30  Allen Bolt, M8x50mm  4 

16  Protecting Plastic, 48x43mm  2  31  Allen Bolt, M8x40mm  2 

17  Protecting Plastic, 35x48mm  2  32  Rivet  4 

18  Protecting Plastic, 311x48mm  2      8 

  

ASSEMBLY STEPS STEP 1

Assemble base frame. Attach rear base frame [1] to front base frame [2] using the long, M12x125mm bolts [29]. Slip (1)                                   M12 flat washer [26] over each bolt before running through front base frame and out other side of                                   rear base frame, then add another washer and an M12 nylon nut [28].   

 

_ V.04.14.2015 

2 

STEP 2 Install uprights. Slip top upright [3] into assembled base frame, locking into place with pin [5]. Note the orientation of the J­hook upright in the picture below.  

   

STEP 3 Attach spotter arms. Spotter arms attach with remaining lock pins. Note: Tighten all nuts & bolts with wrenches prior to use.   

  

 

_ V.04.14.2015 

3 

SPECIAL PRECAUTIONS YOU CAN’T LIFT WHEN YOU’RE DEAD  

! IMPORTANT ! You know these squat stands are designed to handle serious weight ­ 1200lbs. It’s probably one of                                 the reasons you bought them. Maxing out these stands requires special precautions. We strongly                           recommend loading the plate horns to weight the stand when going over 400lbs and sandbagging                             the front of the stands when crossing the 800lb mark. Beyond that, best practice is to bolt these                                   things to the floor. Failure to adhere to these recommendations can lead to some very, very                               bad days.   

  

CARING FOR YOUR SQUAT STANDS MAKE YOUR INVESTMENT LAST  

Inspect & tighten Periodically inspect the stands for signs of wear or loosening hardware. Make sure all nuts & bolts                                 are tight. These are designed to support serious weight and deliver reliable service over many                             years, but it will only do so when properly assembled and maintained.  

  

 

CONTACT CFF WITH ANY QUESTIONS WE WANT YOU HAPPY!  

phone: (717) 207­7171 email: sales@cfffit.com  We’re here if you need us. (And we appreciate your feedback!) 

 

_ V.04.14.2015 

4