Embed Size (px)
Citation preview
www.cineversum.com
Part. No.: R599766
CineMax Kit
ASSEMBLY AND CALIBRATION
Ref: T9003000 Rev: 01
2 R599766 - 2.35 Cinemax Kit
ChangesCineVERSUM provides this manual ’as is’ without warranty of any kind, either expressed or implied, including butnot limited to the implied warranties or merchantability and fitness for a particular purpose. CineVERSUM maymake improvements and/or changes to the product(s) and/or the program(s) described in this publication at anytime without notice.This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to theinformation in this publication; these changes are incorporated in new editions of this publication.
CopyrightAll right reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise berecorded, transmitted or stored in a retrieval system without the prior written consent of CineVERSUM.
GuaranteeCineVERSUM provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms ofguarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred duringtransport, as well as for material and manufacturing faults. CineVERSUM must be informed immediately in writingof any complaints.If the purchaser or third party caries out modifications or repairs on goods delivered by CineVERSUM, or if thegoods are handle incorrectly, in particular if the systems are commissioned operated incorrectly or if, after thetransfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of thepurchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributedto programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normalmaintenance are not subject to the guarantee provided by CineVERSUM either.The environmental conditions as well as the servicing and maintenance regulations specified in this manual mustbe complied with by the customer.
TrademarksBrand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights oftheir respective holders. All brands and product names mentioned in this manual serve as comments or examplesand are not to be understood as advertising for the products of their manufactures.
TABLE OF CONTENTS
1.0 2.35 Cinemax Kit .............................................................................................................. 41.1 Installing the Mounting Plate............................................................................................................. 41.2 Cinemax prismatic Lens alignment ................................................................................................... 5
Adjust the full screen picture .............................................................................................. 5Set the horizontal picture position into the screen .............................................................. 6Set the tilt and vertical position of the lens ......................................................................... 7
1.3 Install the Lens Cap ........................................................................................................................... 8
2.0 Projector-side configuration ............................................................................................ 82.1 Configure the 12V Trigger 2.............................................................................................................. 8
Connect your screen control device to the 12V Trigger 2 output ...................................... 8 Configure Initial Setup Menu -> Trigger 2 to THEATRE .............................................. 8
2.2 Configure the Anamorphic Aspect Ratios ......................................................................................... 916:9 input: Aspect Ratio to Converted 16:9 .................................................................... 9Cinemascope input: Aspect Ratio to Cinemascope ......................................................... 9
2.3 Using the Remote Control Unit. ...................................................................................................... 10Select the correct Aspect Ratio for each input .................................................................. 10[ASPECT] button behavior ............................................................................................... 11Quick Aspect Ratio change on the same input.................................................................. 11
2.4 Using RS-232 protocole................................................................................................................... 11Communication Specifications ......................................................................................... 11Command Format.............................................................................................................. 12Available Lengths and Commands.................................................................................... 12
3.0 Miscellaneous .................................................................................................................. 143.1 Dimensions ...................................................................................................................................... 143.2 Projection distances ......................................................................................................................... 14
R599766 - 2.35 Cinemax Kit 3
1.0 2.35 CINEMAX KIT
1.0 2.35 CINEMAX KIT
The 2.35 Cinemax Kit is a simple and versatile solution to operate a cinemascope experience using the Cinemaxprismatic Lens.The Blackwing One features an exclusive THEATRE Mode for an easier screen masking control.The new THEATRE Mode features:
• Integrated CIW system.
• Dedicated menu to program the 12V Trigger2 output to control your motorized screen mask.
• Direct access button on the Remote Control Unit to switch between Anamorphic modes.
1.1 Installing the Mounting Plate
a)Use the 3x M6x15 screws to fix the plate at the bottom ofthe projector.
b) Use the 4x M5x7 screws to fix the lens support. to thefixing plate and the 2 round head screws to fix theCinemax prismatic Lens in front of the projector lens.
M6x15 screews
round head screwsM5x7
4 R599766 - 2.35 Cinemax Kit
1.0 2.35 CINEMAX KIT
1.2 Cinemax prismatic Lens alignment
Adjust the full screen pictureTo obtain a 2.35 picture, you can use a 16:9 picture set to Full Screen aspect ratio. The picture must fulfill thescreen. These adjustment are made by using the Zoom and the vertical shift and horizontal shift of the projector.When the picture position is correct, adjust the picture focus.
Adjust the Zoom and the Lens Offset until the picture fulfills the screen.
ZOOM
ZOOM
R599766 - 2.35 Cinemax Kit 5
1.0 2.35 CINEMAX KIT
Adjust the picture Focus
Set the horizontal picture position into the screen
To adjust the horizontal position of the picture into the screen, release the 4 screws (A) and turn the AnamorphicLens left or right to obtain a centered 2.35 picture. Tighten the screws when completed. This adjustment can also beachieved by using the Horizontal Lens Offset.
The Horizontal Lens Offset should be used only for fine adjustments. The use of the maximum 30%horizontal offset may decrease the overall picture quality..
FOCUS
AA
6 R599766 - 2.35 Cinemax Kit
1.0 2.35 CINEMAX KIT
Set the tilt and vertical position of the lens
Adjust the Anamorphic Lens tilt and vertical position, so that the projector light beam is centered into theAnamorphic Lens and to compensate the upper and lower pincushion effects. Tighten the 2 screws (B) whencompleted.
You may obtain a residual pincushion effect at the screen when using a throw ratio between 1.5:1 and 1.8:1or a projection distance shorter than 5 meters. It is recommended to install your projector at a minimumdistance of 5 meters from the screen and using 1.8:1 or higher throw ratio with a flat screen. Otherwise, the
use of a curved 2.35 screen is recommended.
B
B
R599766 - 2.35 Cinemax Kit 7
2.0 PROJECTOR-SIDE CONFIGURATION
1.3 Install the Lens Cap
Install the lens Cap and fix it using the 2 screws (C).
2.0 PROJECTOR-SIDE CONFIGURATION
2.1 Configure the 12V Trigger 2
Connect your screen control device to the 12V Trigger 2 output
The 12V Trigger 2 output can control the screen masking
Configure Initial Setup Menu ⇒⇒⇒⇒ Trigger 2 to “THEATRE”The “Initial Setup ⇒⇒⇒⇒ Trigger 2” menu determines the Trigger 2 output located in the panel input of the Blackwing Onethis is a global parameter (for all inputs):
• ON: the 12V Trigger 2 is always active when the projector is switched ON.
• OFF: the 12V Trigger 2 is always switched Off.
• THEATRE: this option turns ON the Trigger 2 output when the aspect ratio is set to “Cinemascope”.
C
C
12V Trigger 1
12V Trigger 2
Screen maskControl
8 R599766 - 2.35 Cinemax Kit
2.0 PROJECTOR-SIDE CONFIGURATION
2.2 Configure the Anamorphic Aspect Ratios
16:9 input: Aspect Ratio to “Converted 16:9”When you select a 16:9 input, choose the Converted 16:9 aspect ratio, and configure the Aspect Ratio between1.30 and 1.40 to obtain the correct geometry.• Select Converted 16:9 in the OSD Menu “Input Signal ⇒⇒⇒⇒ Aspect Ratio ⇒⇒⇒⇒ Converted 16:9”• Then choose the correct Aspect Ratio between 1.30 and 1.40 in the menu ”Input Signal ⇒⇒⇒⇒ Converted 16:9 AspectRatio ⇒⇒⇒⇒ 1.33” so that the 16:9 picture is letter-boxed into the 2.35 screen.
You can rise the Aspect Ratio Mode 2from 1.30 up to 1.78 to reduce the black bars.
Cinemascope input: Aspect Ratio to “Cinemascope”When selecting a wide format input (2.35:1, 2.37:1 or 2.40:1), the original aspect ratio of the source is larger than16:9, you can see black bars on the top and the bottom of the screen.• Select the Anamorphic Mode1 for this input in the “Input Signal ⇒⇒⇒⇒ Aspect Ratio ⇒⇒⇒⇒ Cinemascope”.• Then choose the correct Anamorphic Aspect Ratio between 2.30 and 2.50 in the menu ”Input Signal ⇒⇒⇒⇒Cinemascope Aspect Ratio ⇒⇒⇒⇒ 2.37“ so that the black bars disappear and the active picture fulfills the screen.
Adjust the Aspect Ratio Mode1 between 2.30 and 2.50 to eliminate the black bars.
You can rise the Aspect Ratio up to 1.78 to reduce the black bars on the left and the right of the screen butthe picture may be horizontally stretched.
You can lower the Aspect Ratio Mode1 down to 1.78 if you plan to watch an original 16:9 program withupper and lower picture portion lost. The picture may be horizontally stretched.
1.33x 1.60x
2.34x 2.37x
R599766 - 2.35 Cinemax Kit 9
2.0 PROJECTOR-SIDE CONFIGURATION
2.3 Using the Remote Control Unit.
Blackwing One RCU and quick access features
Select the correct Aspect Ratio for each inputOn the first install, configure the desired Aspect Ratio for each input. By example, a TV source on HDMI1 will useConverted 16:9 (16:9 native format) and a Blu-Ray player on HDMI2 will use Cinemascope (Cinemascope format).Each input retains the last Aspect Ratio applied, so that selecting a different input with the RCU automaticallychoose the correct Aspect Ratio.
Select active input
Select the correctAspect Ratio
10 R599766 - 2.35 Cinemax Kit
2.0 PROJECTOR-SIDE CONFIGURATION
[ASPECT] button behaviorThe [ASPECT] button triggers the 5 aspect ratio modes. Once a given aspect ratio is validated, the order of the nextaspect ratio is reversed so that the previous aspect ratio becomes the next aspect ratio as described below.
Quick Aspect Ratio change on the same inputThe Remote Control Unit can be used to quickly switch the aspect ratio by pressing twice the [ASPECT] button toswitch forth and backward from Cinemascope to Converted 16:9 as described below:
2.4 Using RS-232 protocole
Communication SpecificationsControl of 2.35 THEATRE Concept is possible using a computer or automation device connected with a RS-232straight cable connected to the Blackwing One (male - female D-sub 9 pins cable). Communication specifications
Standard Cinemascope
Converted 16:9
Full Screen
Virtual Wide
When you press sequentially the [ASPECT] button, the aspect mode rotation goes clock-wise. Press [ESC] or wait 15 seconds until the message fades out to confirm
Next time that you will press the [ASPECT] button, the rotation order is reversed. This
The Cinemax Kit uses Converted 16:9 andand Cinemascope modes.
behavior ensures a fast switch between two particular aspect ratios.
selection.
Converted 16:9 Cinemascope
... press twice [ASPECT] button on the Remote Control Unit
When the source automatically switches format...
16:9 picture
2.35:1 picture
Full Screenon 2.35 screen
R599766 - 2.35 Cinemax Kit 11
2.0 PROJECTOR-SIDE CONFIGURATION
for this unit are as follows:
Command Format
When sending a command to this unit, use the following data format:
Available Lengths and Commands
Baud Rate 115200 bps
Data Format Binary
Character Length 8 bits
Parity None
Stop Bit 1 bit
X on/off None
Flow Control None
Header Length Command EoD1 or 3 bytes 0 or 1 byte at least 1 byte 1 byte
Header (00h) for power ON command, (77h 88h 99h) for other commands.
Length The total bytes of “Length” and “Command”
Command Designates the command
EoD Designates the end of the data. Fixed to (FFh)
Command Header (00h)
Length Command Description
Power ON None 01h If the projector is in standby mode, this commandswitch the unit ON.
Command Header(77h 88h 99h)
Length Command Description
Power OFF03h 02h 01hh If the projector is powered ON, this command
switch this unit into Standby Mode. (Directly OFF)Switch Input 03h 02h 02h Switch active input to Video (Composite)
02h 03h Switch active input to S-Video02h 04h Switch active input to Component02h 05h Switch active input to VGA (sD15)02h 06h Switch active input to HDMI 102h 07h Switch active input to HDMI 2
Blanking 03h 02h 08h Toggle projector Blanking ON02h 09h Toggle projector Blanking OFF
Keypad 03h 01h 01h MENU: Toggle OSD Menu ON and OFF01h 02h UP: Uses as up function key for navigation01h 03h DOWN: Uses as down function key for navigation01h 04h LEFT: Uses as left function key for navigation01h 05h RIGHT: Uses as right function key for navigation01h 06h ENTER: Selects menu item or the next menu01h 07h EXIT: exits the current menu to the previous one.01h 08h SOURCE: Switch input source.01h 09h Power OFF: Turn off the projector (send twice)
12V Trigger #2 03h 03h 01h Switch the trigger to ON.03h 02h Switch the trigger to OFF03h 03h Switch the trigger to THEATRE
12 R599766 - 2.35 Cinemax Kit
2.0 PROJECTOR-SIDE CONFIGURATION
Examples
Aspect Ratio 03h 03h 04h Switch aspect ratio to Standard03h 05h Switch aspect ratio to Full Screen03h 06h Switch aspect ratio to Cinemascope03h 07h Switch aspect ratio to Converted 16:903h 08h Switch aspect ratio to Virtual Wide
Lens Aperture 03h 03h 09h Open one level up the Lens Aperture03h 0Ah Close on level down the Lens Aperture
Picture Mode 03h 04h 01h Switch picture mode to Standard04h 02h Switch picture mode to Dynamic04h 03h Switch picture mode to Theater04h 04h Switch picture mode to User 104h 05h Switch picture mode to User 204h 06h Switch picture mode to User 3
Picture Adjust 03h 05h 01h Show brightness slider (use left or right to modify)05h 02h Show contrast slider05h 03h Show colour slider05h 04h Show hue slider05h 05h Show sharpness slider05h 06h Show black level slider05h 07h Show white level slider
Colour Temperature 03h 06h 01h Switch colour temperature to Low06h 02h Switch colour temperature to medium06h 03h Switch colour temperature to High06h 04h Switch colour temperature to User 106h 05h Switch colour temperature to User 206h 06h Switch colour temperature to User 306h 07h Switch colour temperature to Medium-high
Gamma 03h 07h 01h Switch gamma to Gamma 107h 02h Switch gamma to Gamma 207h 03h Switch gamma to Gamma 307h 04h Switch gamma to Gamma 407h 05h Switch gamma to User 107h 06h Switch gamma to User 207h 07h Switch gamma to User 3
Scaling features 03h 08h 01h Set detail enhancement to Off08h 02h Set detail enhancement to Low08h 03h Set detail enhancement to Medium08h 04h Set detail enhancement to High
Temporal Noise 03h 08h 05h Set TNR to Off08h 06h Set TNR to Low08h 07h Set TNR to Medium08h 08h Set TNR to High
Mosquito Noise 03h 09h 01h Set MNR to Off09h 02h Set MNR to Low09h 03h Set MNR to Medium09h 04h Set MNR to High
Block Artifact 03h 09h 05h Set BAR to Off09h 06h Set BAR to On
Reset to default 03h 0Ah 01h Reset settings to default value
You want to... Command to sendSwitch the projector ON 00h 01h FFhSwitch the projector OFF 77h 88h 99h 03h 02h 01h FFhSwitch the projector OFF with OSD confirmation 77h 88h 99h 03h 01h 09h FFh
R599766 - 2.35 Cinemax Kit 13
3.0 MISCELLANEOUS
3.0 MISCELLANEOUS
3.1 Dimensions
3.2 Projection distances
Switch Aspcet Ratio mode to Cinemascope 77h 88h 99h 03h 03h 06h FFhSwitch Aspcet Ratio mode to Converted 16:9 77h 88h 99h 03h 03h 07h FFh
Projection Screen SizeDiagonal size
(Aspect Ratio 2.35:1)
Projection Screen Base size
Projection ScreenHeight
Blackwing One
Projecting Distanceminimum - maximum
107" (2720 mm) 98.4" (2500 mm) 41.7" (1060 mm) 3000 mm - 4100 mm
128" (3250 mm) 118.1" (3000 mm) 50.4" (1280 mm) 3500 mm - 4900 mm
149" (3780 mm) 137.8" (3500 mm) 58.7" (1490 mm) 4010 mm - 5700 mm
170" (4520 mm) 157.5" (4000 mm) 66.9" (1700 mm) 4600 mm - 6500 mm
200" (5080 mm) 184.3" (4680 mm) 77.5" (1970 mm) 5400 mm - 7600 mm
530 mm 530 mm
199 mm7.8’’
20.9’’ 20.9’’
800m
m
31.5
’’
800mm
31.5’’
14 R599766 - 2.35 Cinemax Kit
Contact Information:
TEC - CineVERSUM7, rue La CAILLE, 75017 Paris - FRANCEWeb: www.cineversum.com
Contact informationTEC - CineVERSUM7, rue La Caille, 75017 Paris, Francewww.cineversum.com
Part. No. R599766
