Cisco Catalyst 3750-E Series Switches · 2017-08-18 · Cisco TwinGig converter module for migrating uplinks from Gigabit Ethernet to 10 Gigabit ... the Cisco Catalyst 3750-E Series

Data Sheet

© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1 of 22

Cisco Catalyst 3750-E Series Switches

The Cisco® Catalyst® 3750-E Series Switches with StackWise Plus (Figure 1) is an

enterprise-class line of stackable wiring closet switches that facilitates the deployment of

secure converged applications while maximizing investment protection for evolving

network and application requirements. Combining 10/100/1000 and Power over Ethernet

(PoE) configurations with 10 Gigabit Ethernet uplinks, the Cisco Catalyst 3750-E

enhances worker productivity by enabling applications such as IP telephony, wireless, and

video.

Cisco Catalyst 3750-E Series Primary Features

● Cisco TwinGig converter module for migrating uplinks from Gigabit Ethernet to 10 Gigabit

Ethernet

● Cisco EnergyWise for greenhouse gas emissions and operational cost optimization by

measuring, reporting, and reducing energy consumption across the entire corporate

infrastructure, well beyond the scope of IT

● PoE configurations with up to 15.4 W of PoE on all 48 ports

● Enhanced PoE supporting up to 20W of PoE per port

● StackWise Plus for ease of use and resiliency with 64 Gbps of throughput

● Modular power supply with externally available backup

● Multicast routing, IPv6 routing, and access control list in hardware

● Out-of-band Ethernet management port along with RS-232 console port

Figure 1. Cisco Catalyst 3750-E Series Switches (front and back)

Switch Configurations

Table 1 shows the Cisco Catalyst 3750-E Series configurations:

Table 1. Switch Configurations

Feature Description

Cisco Catalyst 3750E-24TD 24 Ethernet 10/100/1000 ports and 2 X2 10 Gigabit Ethernet uplinks

Cisco Catalyst 3750E-24PD 24 Ethernet 10/100/1000 ports with PoE and 2 X2 10 Gigabit Ethernet uplinks

Cisco Catalyst 3750E-48TD 48 Ethernet 10/100/1000 ports and 2 X2 10 Gigabit Ethernet uplinks

Cisco Catalyst 3750E-48PD 48 Ethernet 10/100/1000 ports with PoE and 2 X2 10 Gigabit Ethernet uplinks

Cisco Catalyst 3750E-48PD-F 48 Ethernet 10/100/1000 ports with > 15.4 watts PoE on all 48 ports and 2 X2 10 Gigabit Ethernet uplinks

Data Sheet


Cisco Catalyst 3750-E Software

Cisco Catalyst 3750-E Series is available with either the IP Base or the IP Services feature set.

The IP Base feature set includes advanced quality of service (QoS), a suite of security features,

rate-limiting, access control lists, and basic static and Routing Information Protocol (RIP) routing

capability. The IP Services feature set provides a richer set of enterprise-class features, including

advanced hardware-based IP unicast and multicast routing—Enhanced Interior Gateway Routing

Protocol (EIGRP), Open Shortest Path First (OSPF), Border Gateway Protocol (BGP), Protocol

Independent Multicast (PIM), and IPv6 routing such as OSPFv3 and EIGRPv6.

Customers can transparently upgrade the software feature set in the Cisco Catalyst 3750-E Series

Switches through Cisco IOS® Software Activation. Software activation authorizes and enables the

Cisco IOS Software feature sets. A special file contained in the switch, called a license file, is

examined by Cisco IOS Software when the switch is powered on. Based on the license’s type,

Cisco IOS Software activates the appropriate feature set. License types can be changed, or

upgraded, to activate a different feature set. For detailed information about Software Activation,

visit http://www.cisco.com/go/sa.

Investment Protection

The Cisco Catalyst 3750-E Series Switches are compatible with the Cisco Catalyst 3750 Series

Switches, enabling customers to stack them together and thereby protect existing investment in

the Cisco Catalyst 3750 Series Switches. The Cisco TwinGig Small Form-Factor Pluggable (SFP)

converter module further protects customers’ investment in Cisco Catalyst 3750-E Series Switches

by enabling migration from Gigabit Ethernet to 10 Gigabit Ethernet uplinks, as business needs

require, without having to upgrade the switches.

Cisco StackWise Plus Technology

Cisco StackWise Plus technology is built on the highly successful StackWise™ technology, which

is a premium stacking architecture optimized for Gigabit Ethernet. StackWise technology was

designed to respond to additions, deletions, and redeployment while maintaining constant

performance. The stack behaves as a single switching unit that is managed by a master switch

elected from one of the member switches. The master switch automatically creates and updates all

the switching and optional routing tables. A working stack can accept new members or delete old

ones without service interruption. StackWise creates a highly resilient single unified system of up

to nine switches, providing simplified management using a single IP address, single telnet session,

single command-line interface (CLI), auto-version checking, autoconfiguration, and more.

StackWise Plus supports all the features of StackWise and provides backward compatibility with

the existing Cisco Catalyst 3750 Series Switches while enhancing the throughput of the system up

to 64 Gbps. StackWise Plus also enables local switching in Cisco Catalyst 3750-E Series

Switches. Local switching packets coming into a port in the Cisco Catalyst 3750-E Series Switch

destined for another port in the same switch do not have to traverse through the stack ring, thus

increasing the forwarding capacity of the switch.

Cisco EnergyWise Technology

Cisco EnergyWise is an innovative architecture, added to the Cisco Catalyst 3750-E switches,

promoting companywide sustainability by reducing energy consumption across an entire corporate

infrastructure and affecting more than 50 percent of global greenhouse gas emissions created by

worldwide building infrastructure, a much greater effect than the 2 percent generated by the IT

industry. Cisco EnergyWise enables companies to measure the power consumption of network

infrastructure and network-attached devices and manage power consumption with specific

http://www.cisco.com/go/sa

Data Sheet


policies, reducing power consumption to realize increased cost savings, potentially affecting any

powered device.

EnergyWise encompasses a highly intelligent network-based approach to communicate messages

that measure and control energy between network devices and endpoints. The network discovers

Cisco EnergyWise manageable devices, monitors their power consumption, and takes action

based on business rules to reduce power consumption. EnergyWise uses a unique domain-

naming system to query and summarize information from large sets of devices, making it simpler

than traditional network management capabilities. Cisco EnergyWise’s management interfaces

allow facilities and network management applications to communicate with endpoints and each

other using the network as a unifying fabric. The management interface uses standard SNMP or

SSL to integrate Cisco and third-party management systems.

Cisco EnergyWise extends the network as a platform for power control plane for gathering,

managing, and reducing power consumption of all devices, resulting in companywide optimized

power delivery and reduced energy costs.

10 Gigabit Ethernet Uplinks and the Cisco TwinGig S FP Converter

The Cisco Catalyst 3750-E features wire-speed 10 Gigabit Ethernet uplink ports for high-bandwidth

applications, relieving congestion and ensuring smooth delivery of data. The TwinGig SFP

converter (see Figure 2) converts a 10 Gigabit Ethernet X2 interface into two Gigabit Ethernet SFP

ports. This way, customers can initially use the switch with Gigabit Ethernet uplinks and later

implement 10 Gigabit Ethernet uplinks as business demands change, without having to upgrade

the access layer.

Figure 2. Cisco TwinGig Adapter Converting 10 Gigabit Ethernet X2 Interface into Two Gigabit Ethernet SFP Interfaces

Modular Power Supplies

The Cisco Catalyst 3750-E Series Switches have one power supply slot and support the following

power supplies. PoE switches require a PoE power supply. Data-only switches can operate with

any of the power supplies.

● C3K-PWR-1150WAC: 1150WAC power supply with 800W PoE

● C3K-PWR-750WAC: 750WAC power supply for 24-port switch with 420W PoE

● C3K-PWR-265WAC: 265WAC power supply for 48-port or 24-port switch without PoE

● C3K-PWR-265WDC: 265WDC power supply for 48-port or 24-port switch without PoE

Data Sheet


Maximum power availability for converged voice and data networks is attainable when a Cisco

Catalyst 3750-E Series Switch is combined with the Cisco RPS 2300 Redundant Power System for

transparent protection against internal power supply failures and an uninterruptible power supply

(UPS) system to safeguard against power outages. Using the RPS 2300 to provide backup power,

the Cisco Catalyst 3750-E Series Switch power supplies become hot swappable. Table 3 shows

the power supply compatibility matrix.

Power over Ethernet

The Cisco Catalyst 3750-E Series can provide a lower total cost of ownership for deployments that

incorporate Cisco IP phones, Cisco Aironet® wireless LAN (WLAN) access points, or any IEEE

802.3af-compliant end device. PoE removes the need for wall power to each PoE-enabled device

and eliminates the cost for additional electrical cabling and circuits that would otherwise be

necessary in IP phone and WLAN deployments. The Cisco Catalyst 3750-E 24-port PoE

configurations can support 24 simultaneous full-powered PoE ports at 15.4W for full powered-

device support. The Cisco Catalyst 3750-E 48-port PoE configurations can support 48

simultaneous full-powered PoE ports at 15.4W when using the optional 1150W power supply.

Alternatively, for deployments that do not need full PoE on all ports, a smaller power supply can be

used in conjunction with Cisco Catalyst Intelligent Power Management to support 24-port and 48-

port PoE configurations.

In addition, Cisco Catalyst Intelligent Power Management supports Enhanced PoE where up to

20W of PoE can be delivered to each port. This capability enables support of PoE devices such as

802.11n wireless equipment where >15.4W of PoE is required.

Redundant Power System

The Cisco Catalyst 3750-E Series Switches support the new generation of Redundant Power

Supply (RPS) 2300. The RPS 2300 increases availability in a converged data, voice, and video

network by providing transparent power backup to two of six attached Cisco Catalyst 3750-E

Series Switches at the same time. The failed power supply can be swapped out while the switch is

being powered up by the RPS 2300.

Primary Features and Benefits

Ease of Use: Deployment

A working stack is self-managing and self-configuring. When switches are added or removed, the

master switch automatically loads the Cisco IOS Software version running on the stack to the new

switch, loads the global configuration parameters, and updates all the routing tables to reflect

changes. Upgrades are applied universally and simultaneously to all members of the stack.

The Cisco Catalyst 3750-E Series stacks up to nine switches as a single logical unit for a total of

468 Ethernet 10/100/1000 ports, 432 PoE 10/100/1000 ports, or 18 10 Gigabit Ethernet ports.

Individual 10/100/1000 units can be joined in any combination to evolve with network needs.

Other ease of use features include but are not limited to:

● Smartports enable fast and easy configuration of Cisco recommended best practice

security and QoS features, encapsulating years of Cisco networking expertise.

● Dynamic Host Configuration Protocol (DHCP) autoconfiguration of multiple switches

through a boot server eases switch deployment.

Data Sheet


● Automatic QoS (AutoQoS) simplifies QoS configuration in voice over IP (VoIP) networks by

issuing interface and global switch commands to detect Cisco IP phones, classify traffic,

and help enable egress queue configuration.

● Master configuration management helps ensure that all switches are automatically

upgraded when the master switch receives a new software version. Automatic software

version checking and updating help ensure that all stack members have the same software

version.

● Autonegotiation on all ports automatically selects half- or full-duplex transmission mode to

optimize bandwidth.

● Dynamic Trunking Protocol (DTP) facilitates dynamic trunk configuration across all switch

ports.

● Port Aggregation Protocol (PAgP) automates the creation of Cisco Fast EtherChannel®

groups or Gigabit EtherChannel groups to link to another switch, router, or server.

● Link Aggregation Control Protocol (LACP) allows the creation of Ethernet channeling with

devices that conform to IEEE 802.3ad. This feature is similar to Cisco EtherChannel

technology and PAgP.

● Automatic media-dependent interface crossover (MDIX) automatically adjusts transmit and

receive pairs if an incorrect cable type (crossover or straight-through) is installed.

● Unidirectional Link Detection Protocol (UDLD) and Aggressive UDLD allow unidirectional

links caused by incorrect fiber-optic wiring or port faults to be detected and disabled on

fiber-optic interfaces.

High Availability

The Cisco Catalyst 3750-E Series increases availability for stackable switches. Each switch can

operate both as master controller and as forwarding processor. Each switch in the stack can serve

as a master, creating a 1:N availability scheme for network control. In the unlikely event of a single

unit failure, all other units continue to forward traffic and maintain operation.

Other high-availability features include but are not limited to:

● Cross-Stack EtherChannel provides the ability to configure Cisco EtherChannel technology

across different members of the stack for high resiliency.

● Flexlink provides link redundancy with convergence time less than 100 ms.

● IEEE 802.1s/w Rapid Spanning Tree Protocol (RSTP) and Multiple Spanning Tree Protocol

(MSTP) provide rapid spanning-tree convergence independent of spanning-tree timers and

also offers the benefit of Layer 2 load balancing and distributed processing. Stacked units

behave as a single spanning-tree node.

● Per-VLAN Rapid Spanning Tree (PVRST+) allows rapid spanning-tree reconvergence on a

per-VLAN spanning-tree basis, without requiring the implementation of spanning-tree

instances.

● Cisco Hot Standby Router Protocol (HSRP) is supported to create redundant, failsafe

routing topologies.

● Switch-port autorecovery (Errdisable) automatically attempts to reactivate a link that is

disabled because of a network error.

Data Sheet


High-Performance IP Routing

Cisco Express Forwarding hardware routing architecture delivers extremely high-performance IP

routing in the Cisco Catalyst 3750-E Series Switches.

● IP unicast routing protocols (Static, Routing Information Protocol Version 1 [RIPv1], and

RIPv2, RIPng, EIGRP stub) are supported for small-network routing applications.

● Advanced IP unicast routing protocols (OSPF, EIGRP, BGPv4 and IS-ISv4) are supported

for load balancing and constructing scalable LANs. IPv6 routing (OSPFv3, EIGRPv6) is

supported in hardware for maximum performance. The IP Services feature set is required.

● Equal-cost routing facilitates Layer 3 load balancing and redundancy across the stack.

● Policy-based routing (PBR) allows superior control by facilitating flow redirection regardless

of the routing protocol configured. The IP Services feature set is required.

● HSRP provides dynamic load balancing and failover for routed links, up to 32 HSRP links

supported per unit or stack.

● Protocol Independent Multicast (PIM) for IP multicast routing is supported, including PIM

sparse mode (PIM-SM), PIM dense mode (PIM-DM), PIM sparse-dense mode and Source

Specific Multicast (SSM). The IP Services feature set is required.

Superior Quality of Service

The Cisco Catalyst 3750-E Series offers Gigabit Ethernet speed with intelligent services that keep

everything flowing smoothly, even at 10 times the normal network speed. Industry-leading

mechanisms for marking, classification, and scheduling deliver superior performance for data,

voice, and video traffic, all at wire speed.

Following are some of the QoS features supported in the Cisco Catalyst 3750-E Series Switches:

● Cross-stack QoS allows QoS to be configured across the entire stack.

● 802.1p class of service (CoS) and differentiated services code point (DSCP) field

classification is provided, using marking and reclassification on a per-packet basis by

source and destination IP address, MAC address, or Layer 4 TCP/UDP port number.

● Cisco control-plane and data-plane QoS ACLs on all ports help ensure proper marking on a

per-packet basis.

● Four egress queues per port help enable differentiated management of up to four traffic

types across the stack.

● Shaped Round Robin (SRR) scheduling helps ensure differential prioritization of packet

flows by intelligently servicing the ingress queues and egress queues.

● Weighted Tail Drop (WTD) provides congestion avoidance at the ingress and egress

queues before a disruption occurs.

● Strict priority queuing helps ensure that the highest-priority packets are serviced ahead of

all other traffic.

● The Cisco committed information rate (CIR) function provides bandwidth in increments as

low as 8 Kbps.

● Rate limiting is provided based on source and destination IP address, source and

destination MAC address, Layer 4 TCP/UDP information, or any combination of these

fields, using QoS ACLs (IP ACLs or MAC ACLs), class maps, and policy maps.

Data Sheet


● Up to 64 aggregate or individual policers are available per Fast Ethernet or Gigabit

Ethernet port.

Advanced Security

The Cisco Catalyst 3750-E Series supports a comprehensive set of security features for

connectivity and access control, including ACLs, authentication, port-level security, and identity-

based network services with 802.1x and extensions. This set of comprehensive features not only

helps prevent external attacks, but defends the network against “man-in-the-middle” attacks, a

primary concern in today’s business environment. The switch also supports the Network

Admission Control (NAC) security framework.

● Dynamic ARP Inspection (DAI) helps ensure user integrity by preventing malicious users

from exploiting the insecure nature of the ARP protocol.

● DHCP Snooping prevents malicious users from spoofing a DHCP server and sending out

bogus addresses. This feature is used by other primary security features to prevent a

number of other attacks such as ARP poisoning.

● IP source guard prevents a malicious user from spoofing or taking over another user’s IP

address by creating a binding table between the client’s IP and MAC address, port, and

VLAN.

● Private VLANs restrict traffic between hosts in a common segment by segregating traffic at

Layer 2, turning a broadcast segment into a nonbroadcast multi-access-like segment.

● Private VLAN Edge provides security and isolation between switch ports, which helps

ensure that users cannot snoop on other users’ traffic.

● Unicast RPF feature helps mitigate problems caused by the introduction of malformed or

forged (spoofed) IP source addresses into a network by discarding IP packets that lack a

verifiable IP source address.

● IEEE 802.1x allows dynamic, port-based security, providing user authentication.

● IEEE 802.1x with VLAN assignment allows a dynamic VLAN assignment for a specific user

regardless of where the user is connected.

● IEEE 802.1x with voice VLAN permits an IP phone to access the voice VLAN irrespective of

the authorized or unauthorized state of the port.

● IEEE 802.1x and port security are provided to authenticate the port and manage network

access for all MAC addresses, including that of the client.

● IEEE 802.1x with an ACL assignment allows for specific identity-based security policies

regardless of where the user is connected.

● IEEE 802.1x with guest VLAN allows guests without 802.1x clients to have limited network

access on the guest VLAN.

● Web authentication for non-802.1x clients allows non-802.1x clients to use an SSL-based

browser for authentication.

● Multi-Domain Authentication allows an IP phone and a PC to authenticate on the same

switch port while placing them on appropriate Voice and Data VLAN.

● MAC Auth Bypass (MAB) for voice allows third-party IP phones without an 802.1x

supplicant to get authenticated using the MAC address.

● Cisco security VLAN ACLs on all VLANs prevents unauthorized data flows from being

bridged within VLANs.

Data Sheet


● Cisco standard and extended IP security router ACLs define security policies on routed

interfaces for control-plane and data-plane traffic. IPv6 ACLs can be applied to filter

IPv6 traffic.

● Port-based ACLs for Layer 2 interfaces allow security policies to be applied on individual

switch ports.

● Secure Shell (SSH) Protocol, Kerberos, and Simple Network Management Protocol Version

3 (SNMPv3) provide network security by encrypting administrator traffic during Telnet and

SNMP sessions. SSH Protocol, Kerberos, and the cryptographic version of SNMPv3 require

a special cryptographic software image because of U.S. export restrictions.

● Bidirectional data support on the Switched Port Analyzer (SPAN) port allows Cisco Intrusion

Detection System (IDS) to take action when an intruder is detected.

● TACACS+ and RADIUS authentication facilitates centralized control of the switch and

restricts unauthorized users from altering the configuration.

● MAC Address Notification allows administrators to be notified of users added to or removed

from the network.

● Port Security secures the access to an access or trunk port based on MAC address.

● Multilevel security on console access prevents unauthorized users from altering the switch

configuration.

● Bridge protocol data unit (BPDU) Guard shuts down Spanning Tree PortFast-enabled

interfaces when BPDUs are received to avoid accidental topology loops.

● Spanning Tree Root Guard (STRG) prevents edge devices not in the network

administrator’s control from becoming Spanning Tree Protocol root nodes.

● IGMP filtering provides multicast authentication by filtering out nonsubscribers and limits

the number of concurrent multicast streams available per port.

● Dynamic VLAN assignment is supported through implementation of VLAN Membership

Policy Server client capability to provide flexibility in assigning ports to VLANs. Dynamic

VLAN facilitates the fast assignment of IP addresses.

Intelligent Power over Ethernet (PoE) Management

The Cisco Catalyst 3750-E PoE models support Cisco IP phones and Cisco Aironet WLAN access

points, as well as any IEEE 802.3af-compliant end device. The Cisco Catalyst 3750-E-48PD can

support 48 simultaneous full-powered PoE ports at 15.4W with the 1150W power supply.

● Cisco Discovery Protocol version 2 (CDPv2) allows the Cisco Catalyst 3750-E Series

Switch to negotiate a more granular power setting when connecting to a Cisco powered

device such as IP phones or access points than what is provided by IEEE classification.

● Per Port power consumption command allows customers to specify maximum power setting

on an individual port.

● Per Port PoE Power Sensing measures actual power being drawn, enabling more intelligent

control of powered devices.

● The PoE MIB provides proactive visibility into power usage and allows customers to set

different power level thresholds

Data Sheet


Management and Control Features

Each Cisco Catalyst 3750-E Series stack is managed as a single object and has a single

IP address. The primary management and control features in the Cisco Catalyst 3750-E

Switches include:

● Cisco IOS Software CLI support provides common user interface and command set with all

Cisco routers and Cisco Catalyst desktop switches.

● Switching Database Manager Templates for access, routing, and VLAN deployment allow

the administrator to easily maximize memory allocation to the desired features based on

deployment-specific requirements.

● Generic On-Line Diagnostic (GOLD) checks the health of hardware components and

verifies proper operation of the system data and control plane at run time and boot time.

● Virtual routing and forwarding (VRF)-Lite enables a service provider to support two or more

VPNs, with overlapping IP addresses.

● Local Proxy Address Resolution Protocol (ARP) works in conjunction with Private VLAN

Edge to minimize broadcasts and maximize available bandwidth.

● VLAN1 minimization allows VLAN1 to be disabled on any individual VLAN trunk.

● Smart Multicast, with Cisco StackWise Plus technology, allows the Cisco Catalyst 3750-E

Series to offer greater efficiency and support for more multicast data streams such as video

by putting each data packet onto the backplane only once.

● Internet Group Management Protocol (IGMP) Snooping for IPv4 and IPv6 MLD v1 and v2

Snooping provide fast client joins and leaves of multicast streams and limit bandwidth-

intensive video traffic to only the requestors.

● Multicast VLAN Registration (MVR) continuously sends multicast streams in a multicast

VLAN while isolating the streams from subscriber VLANs for bandwidth and security

reasons.

● Per-port broadcast, multicast, and unicast storm control prevents faulty end stations from

degrading overall systems performance.

● Voice VLAN simplifies telephony installations by keeping voice traffic on a separate VLAN

for easier administration and troubleshooting.

● Cisco VLAN Trunking Protocol (VTP) supports dynamic VLANs and dynamic trunk

configuration across all switches.

● Remote Switch Port Analyzer (RSPAN) allows administrators to remotely monitor ports in a

Layer 2 switch network from any other switch in the same network.

● For enhanced traffic management, monitoring, and analysis, the Embedded Remote

Monitoring (RMON) software agent supports four RMON groups (history, statistics, alarms,

and events).

● Layer 2 traceroute eases troubleshooting by identifying the physical path that a packet

takes from source to destination.

● Trivial File Transfer Protocol (TFTP) reduces the cost of administering software upgrades

by downloading from a centralized location.

● Network Timing Protocol (NTP) provides an accurate and consistent timestamp to all

intranet switches.

Data Sheet


● Multifunction LEDs per port for port status; half-duplex and full-duplex mode; and 10BASE-

T, 100BASE-TX, and 1000BASE-T indication as well as switch-level status LEDs for

system, redundant-power supply, and bandwidth utilization provide a comprehensive and

convenient visual management system.

● Jumbo frames (9216 bytes) are available on the 10/100/1000 configurations for advanced

data and video applications requiring very large frames.

Network Management Tools

The Cisco Catalyst 3750-E Series offers both a superior CLI for detailed configuration and Cisco

Network Assistant Software, a PC-based tool for quick configuration based on preset templates. In

addition, CiscoWorks LAN Management Solution (LMS) supports the Cisco Catalyst 3750-E Series

for networkwide management.

Cisco Network Assistant

A PC-based network management application designed for small and medium-sized business

(SMB) networks with up to 250 users, Cisco Network Assistant offers centralized network

management and configuration capabilities. Cisco Network Assistant uses Cisco Smartports

technology to simplify both initial deployment and ongoing maintenance. This application also

features an intuitive GUI where users can easily apply common services across Cisco switches,

routers, and access points, such as:

● Configuration management

● Troubleshooting advice

● Inventory reports

● Event notification

● Network security settings

● Password synchronization

● Drag-and-drop Cisco IOS Software upgrades

● Secure wireless

For detailed information about Cisco Network Assistant, visit http://www.cisco.com/go/cna.

CiscoWorks LAN Management Solution (LMS)

CiscoWorks LMS is a suite of powerful management tools that simplify the configuration,

administration, monitoring and troubleshooting of Cisco networks. It integrates these capabilities

into a world-class solution for improving the accuracy and efficiency of your operations staff, while

increasing the overall availability of your network. LMS supports over 400 different device types

including the 3750-E and 3560-E series switches and it provides:

● Network discovery, topology views, end-station tracking and VLAN management

● Real-time network fault analysis with easy-to-deploy device specific best-practice templates

● Hardware and software inventory management, centralized configuration tools, and Syslog

monitoring

● Network response time and availability monitoring and tracking

● Real-time device, link, and port traffic management, analysis, and reporting

For detailed information about CiscoWorks LMS, go to

http://www.cisco.com/en/US/products/sw/cscowork/ps2425/index.html

http://www.cisco.com/go/cna

http://www.cisco.com/en/US/products/sw/cscowork/ps2425/index.html

Data Sheet


Product Specifications

Table 2 lists product specifications for the Cisco Catalyst 3750-E Series.

Table 2. Descriptions and Specifications

Description Specification

Performance ● 160-Gbps switching fabric capacity

● Stack-forwarding rate of 95 Mpps for 64-byte packets

● Forwarding rate: ◦ 3750E-24TD—65.5 Mpps ◦ 3750E-24PD—65.5 Mpps ◦ 3750E-48TD—101.2 Mpps ◦ 3750E-48PD—101.2 Mpps ◦ 3750E-48PD-F—101.2 Mpps

● Memory: ◦ 256 MB DRAM and 64 MB FLASH

● Feature resources: ◦ 1005 VLANs ◦ 4K VLAN IDs ◦ 1000 switched virtual interfaces (SVIs) ◦ 468 routed ports per stack ◦ 9216 byte jumbo frames

MAC, routing, security, and QoS scalability numbers depend on the type template used in the switch :

Default Access VLAN Routing

MAC address 6K 4K 12K 3K

IGMP groups and multicast routes

1K 1K 1K 1K

Total unicast routes 8K 6K 0 11K

Directly connected hosts 6K 4K 0 3K

Indirect routes 2K 2K 0 8K

Security ACEs 1K 2K 1K 1K

QoS ACEs 0.5K 0.5K 0.5K 0.5K

PBR ACEs 0 0.5K 0 0.5K

Connectors and Cabling ● 1000BASE-T ports: RJ-45 connectors, 2-pair Cat-5E UTP cabling

● 1000BASE-T SFP-based ports: RJ-45 connectors, 2-pair Cat-5E UTP cabling

● 100BASE-FX, 1000BASE-SX, -LX/LH, -ZX, -BX10, and CWDM SFP-based ports: LC fiber connectors (single-mode or multimode fiber)

● 10GBASE-SR, LR, ER, LX4, CX4 X2-based ports: SC fiber connectors (single-mode or multimode fiber)

● Cisco StackWise stacking ports: copper-based Cisco StackWise cabling

● Ethernet Management port: RJ-45 connectors, 2-pair Cat-5 UTP cabling

● Management console port: RJ-45-to-DB9 cable for PC connections

Power Connectors ● Customers can provide power to a switch by using either the internal power supply or the Cisco RPS 2300. The connectors are located at the back of the switch.

● Internal power supply connector: The internal power supply is an autoranging unit. The internal power supply supports input voltages between 100 and 240VAC. Use the supplied AC power cord to connect the AC power connector to an AC power outlet.

● Cisco RPS connector: The connector offers connection for an optional Cisco RPS 2300 that uses AC input and supplies DC output to the switch.

● Only the Cisco RPS 2300 (model PWR2300-AC-RPS-N1=) should be attached to the redundant-power-supply receptacle.

Indicators ● Per-port status LEDs: link integrity, disabled, activity, speed, and full-duplex indications

● System-status LEDs: system, RPS, and bandwidth-utilization indications

Data Sheet


Inches Centimeters

3750E-24TD 1.75 x 17.5 x 18.1 4.45 x 44.5 x 46.0

3750E-24PD 1.75 x 17.5 x 18.1 4.45 x 44.5 x 46.0

3750E-48TD 1.75 x 17.5 x 18.1 4.45 x 44.5 x 46.0

3750E-48PD 1.75 x 17.5 x 18.1 4.45 x 44.5 x 46.0

Dimensions (H x W x D)

3750E-48PD-F 1.75 x 17.5 x 21.7 4.45 x 44.5 x 55.2

Pounds Kilograms

3750E-24TD 17.9 8.1

3750E-24PD 18.3 8.3

3750E-48TD 18.8 8.6

3750E-48PD 19.2 8.75

Weight

3750E-48PD-F 20.9 9.5

Environmental Ranges ● Operating temperature: 32 to 113ºF (0 to 45ºC)

● Storage temperature: –13 to 158ºF (–25 to 70ºC)

● Relative humidity operating: 10 to 85% (noncondensing)

● Relative humidity nonoperating: 0 to 95% (noncondensing)

● Operating altitude: up to 10,000 ft (3049 m)

● Storage altitude: up to 15,000 ft (4573 m)

International Organization for Standardization (ISO) 7779: bystander position operating to an ambient temperature of 30ºC

3750E-24TD 45 dB

3750E-24PD 45 dB

3750E-48TD 45 dB

3750E-48PD 45 dB

Acoustic Noise

3750E-48PD-F 48 dB

3750E-24TD 177,975 hours

3750E-24PD 167,107 hours

33750E-48TD 166,369 hours

3750E-48PD 153,265 hours

Mean Time Between Failure (MTBF)

3750E-48PD-F 149,667 hours

Data Sheet


Table 3 lists the management and standards support for the Cisco Catalyst 3750-E Series.

Table 3. Management and Standards Support for Cisco Catalyst 3750-E Series Switch


Management ● BRIDGE-MIB

● CISCO-CDP-MIB

● CISCO-CLUSTER-MIB

● CISCO-CONFIG-MAN-MIB

● CISCO-ENTITY-FRU-CONTROL-MIB

● CISCO-ENVMON-MIB

● CISCO-FLASH-MIB

● CISCO-FTP-CLIENT-MIB

● CISCO-HSRP-MIB

● CISCO-HSRP-EXT-MIB

● CISCO-IGMP-FILTER-MIB

● CISCO-IMAGE-MIB

● CISCO-IP-STAT-MIB

● CISCO-L2L3-INTERFACE-CONFIG-MIB

● CISCO-POE-EXTENSIONS-MIB

● CISCO-MAC-NOTIFICATION-MIB

● CISCO-MEMORY-POOL-MIB

● CISCO-PAGP-MIB

● CISCO-PING-MIB

● CISCO-PROCESS-MIB

● CISCO-RTTMON-MIB

● CISCO-STP-EXTENSIONS-MIB

● CISCO-SYSLOG-MIB

● CISCO-TCP-MIB

● CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB

● CISCO-VLAN-MEMBERSHIP-MIB

● CISCO-VTP-MIB

● ENTITY-MIB

● ETHERLIKE-MIB

● IF-MIB

● IGMP-MIB

● IPMROUTE-MIB

● OLD-CISCO-CHASSIS-MIB

● OLD-CISCO-FLASH-MIB

● OLD-CISCO-INTERFACES-MIB

● OLD-CISCO-IP-MIB

● OLD-CISCO-SYS-MIB

● OLD-CISCO-TCP-MIB

● OLD-CISCO-TS-MIB

● OSPF-MIB (RFC 1253)

● PIM-MIB

● RFC1213-MIB

● RFC1253-MIB

● RMON-MIB

● RMON2-MIB

● SNMP-FRAMEWORK-MIB

● SNMP-MPD-MIB

● SNMP-NOTIFICATION-MIB

● SNMP-TARGET-MIB

● SNMPv2-MIB

● TCP-MIB

● UDP-MIB

Standards ● IEEE 802.1s

● IEEE 802.1w

● IEEE 802.1x

● IEEE 802.3ad

● IEEE 802.3af

● IEEE 802.3x full duplex on 10BASE-T, 100BASE-TX, and 1000BASE-T ports

● IEEE 802.1D Spanning Tree Protocol

● IEEE 802.1p CoS Prioritization

● IEEE 802.1Q VLAN

● IEEE 802.3 10BASE-T specification

● IEEE 802.3u 100BASE-TX specification

● IEEE 802.3ab 1000BASE-T specification

● IEEE 802.3z 1000BASE-X specification

● 100BASE-FX

● 1000BASE-T

● 1000BASE-SX

● 1000BASE-LX/LH

● 1000BASE-BX10-U

● 1000BASE-BX10-D

● 1000BASE-ZX

● 1000BASE-CWDM SFP 1470 nm








● 10GBASE-SR

● 10GBASE-LR

● 10GBASE-ER

● RMON I and II standards

● SNMPv1, SNMPv2c, and SNMPv3

Data Sheet


Table 4 lists the power supply compatibility matrix for all different models of Cisco Catalyst 3750-E

Series Switches.

Table 4. Power Supply Compatibility Matrix

Cisco Catalyst 3750-E Series Switch Type

Power Supply

C3K-PWR-1150WAC

C3K-PWR-750WAC

C3K-PWR-265WAC

C3K-PWR-265WDC

48-Port PoE Switch X X

24-Port PoE Switch X X

48-Port Switch X X X X

24-Port Switch X X X X

RPS 2300 X X

Table 5 lists the power specifications for the Cisco Catalyst 3750-E Series based on the kind of

power supply used.

Table 5. Power Specifications


C3K-PWR-1150WAC

C3K-PWR-750WAC

C3K-PWR-265WAC

C3K-PWR-265WDC

Power Supply Rated Maximum 1150W 750W 265W 265W

Total Output BTU (Note: 1000 BTU/hr = 293W)

3939 BTU/hr, 1150W

2568 BTU/hr, 765W

907BTU/hr, 265W

907BTU/hr, 265W

Input-Voltage Range and Frequency

115–240VAC,

50–60 Hz

100–240VAC,

50–60 Hz

100–240VAC,

50–60 Hz

-36VDC to -72VDC

Input Current 12–6A 10–5A 5–2.5A <5A@-72VDC

<10A@-36VDC

Output Ratings 12V@25A

–[email protected]

12V@25A

–[email protected]

12V@22A 12V@22A

Output Holdup Time 20 ms minimum 20 ms minimum 20 ms minimum > 2ms@-48VDC

Power-Supply Input Receptacles

IEC 320-C13

(IEC60320-C19)

IEC 320-C13

(IEC60320-C13)

IEC 320-C13

(IEC60320-C13)

Power Cord Rating 15A 15A 15A 12A@-100VDC

Description Specifications

WS-C3750E-48PD-SF

WS-C3750E-24PD-S

WS-C3750E-48PD-S

WS-C3750E-24TD-S

WS-C3750E-48TD-S

C3K-PWR-1150WAC

C3K-PWR-750WAC

C3K-PWR-750WAC

C3K-PWR-265WAC

C3K-PWR-265WAC

100% Throughput

Measured Power Consumption

152W 101W 131W 99W 149W

Measured Output BTU/hr

516 344 445 338 506

5% Throughput


142W 97W 124W 96W 140W


482 331 420 326 475

Data Sheet


5% Throughput (with 50% PoE loads)


Switch Power: 564W

PoE Power: 386W

Switch Power: 304W

PoE Power: 195W

Switch Power: 333W

PoE Power: 196W

N/A N/A


At the Switch: 608 At the Switch: 372 At the Switch: 468 N/A N/A

100% Throughput (with maximum possible PoE loads)


Switch Power: 978W

PoE Power: 744W

Switch Power: 509W

PoE Power: 375W

Switch Power: 540W

PoE Power: 375W

N/A N/A


At the Switch: 796 At the Switch: 456 At the Switch: 562 N/A N/A

Note:

Disclaimer: All power consumption numbers were measured under controlled laboratory conditions

and are provided as an estimate.

The wattage rating on the power supply does not represent actual power draw. It indicates the

maximum power draw possible by the power supply. This rating can be used for facility capacity

planning. For PoE switches, cooling requirements are smaller than the actual power consumption

as a significant portion of PoE loads are dissipated in the endpoints.

Non-PoE Power Consumption

100 Percent Throughput Switch Power Consumption

The numbers indicate the power consumed by a typical switch under normal conditions. Normal

conditions signify a temperature of 25 degrees Celsius, atmospheric pressure in the range of 860

to 1060 mbar, and relative humidity from 30 to 75 percent. Typically such power draws are only

seen when encountering a 100 percent traffic load made up entirely of 64-byte packets on the

switch and the uplinks.

5 Percent Throughput Switch Power Consumption



to 1060 mbar, and relative humidity from 30 to 75 percent. The numbers below indicate a 5

percent traffic load on the switch and its uplinks.

PoE Power Consumption

100 Percent Throughput Switch Power Consumption (no PoE loads)



to 1060 mbar, and relative humidity from 30 to 75 percent. Typically such power draws are only

seen when encountering a 100 percent traffic load made up entirely of 64-byte packets with no

PoE loads on the switch and uplinks.

Measured 5 Percent Throughput Switch Power Consumption (no PoE loads)



to 1060 mbar and relative humidity from 30 to 75 percent. The numbers below indicate a 5 percent

traffic load on the switch and its uplinks

Data Sheet


100 Percent Throughput Switch Power Consumption (with maximum PoE loads)

The numbers indicate the power consumed by a typical system (the switch and the corresponding

PoE loads) under normal conditions. Normal conditions signify a temperature of 25 degrees

Celsius, atmospheric pressure in the range of 860 to 1060 mbar and relative humidity from 30 to

75 percent. Typically this power draw is realized when a switch is running 100 percent traffic load

of 64 byte sized packets on all its ports and uplinks and also drawing 100 percent PoE load .

5 Percent Throughput Switch Power Consumption (with 50 percent PoE loads).

The numbers indicate the power consumed by a typical system (the switch and the corresponding

PoE loads) under normal conditions. Normal conditions signify a temperature of 25 degrees

Celsius, atmospheric pressure in the range of 860 to 1060 mbar and relative humidity from 30 to

75 percent. The numbers below indicate a 5 percent traffic load and 50 percent PoE load on the

switch and its uplinks.

Table 6 lists the specifications of all the power supplies supported in Cisco Catalyst 3750-E Series

Switches.

Table 6. Power Supply Specifications

Product Specifications Power Supply

C3K-PWR-1150WAC

C3K-PWR-750WAC

C3K-PWR-265WAC

C3K-PWR-265WDC

Physical Specifications (H x W x D): 1.65 X 6.0 X 14.90 in

Weight: 5.6 lb (2.6 kg)

(H x W x D): 1.65 X 6.0 X 11.4 in


(H x W x D): 1.65 X 6.0 X 11.4 in


(H x W x D): 1.65 X 6.0 X 11.4 in


Operating Temperature 23 to 113°F (–5 to 45°C)

Storage Temperature –40 to 158°F (–40 to 70°C)

Relative Humidity Operating, Noncondensing

10 to 85% noncondensing

Relative Humidity Nonoperating, Noncondensing

0 to 95% noncondensing

Altitude 10,000 ft. (3000 meters), up to 45°C

MTBF Calculated MTBF must be greater than 300,000 using Telcordia SR-332, Method 1, Case 3. Demonstrated MTBF is 500,000 hr (with 90% confidence level).

EMI and EMC Compliance ● FCC Part 15 (CFR 47) Class A

● ICES-003 Class A

● EN 55022 Class A

● CISPR 22 Class A

● AS/NZS 3548 Class A

● VCCI Class A

● EN 55024

● EN300 386

● EN 50082-1

● EN 61000-3-2

● EN 61000-3-3

● EN 61000-6-1

Safety Compliance ● UL 60950-1 1st Edition

● CAN/CSA-C22.2 No. 60950-1 1st Edition

● EN 60950-1 1st Edition

● IEC 60950-1 1st Edition

LED Indicators “AC OK”: Input power to the power supply is OK.

“PS OK”: Output power from the power supply is OK.

Data Sheet


Table 7 lists the safety and compliance information for the Cisco Catalyst 3750-E Series.

Table 7. Safety and Compliance


Safety Certifications ● UL60950-1 ● C-UL to CAN/CSA 22.2 No.60950-1 ● TUV/GS to EN 60950-1 ● CB to IEC 60950-1 with all country deviations ● AS/NZS 60950-1 ● CE Marking ● CCC for PS FRU ● NOM (through partners and distributors) ● GOST (Russia Safety Mark)

Electromagnetic Emissions Certifications

● FCC Part 15 Class A ● EN 55022B Class A (CISPR22 Class A) ● VCCI Class A ● AS/NZS 3548 Class A or AS/NZS CISPR22 Class A ● MIC ● CE Marking ● GOST (Russian mark—Post FCS thru partners) ● CCC for PS FRU

Environmental Reduction of Hazardous Substances (ROHS) 5

Noise Specifications Office Product Spec: 48dBA at 30°C (refer to ISO 7779)

Telco CLEI code

Warranty Standard 90 Day Limited Hardware and Software Warranty

Hardware Warranty

Cisco Catalyst 3750-E Series Switches come with the Standard Cisco 90-day Limited Warranty for

hardware and software, as described at

http://www.cisco.com/en/US/products/prod_warranties_item09186a00805f005b.html

Cisco Services for Access Switching

Cisco and our partners can help you create a robust, dependable Cisco Access Switching solution.

The Cisco lifecycle approach to services defines the requisite activities at each phase of the

solution lifecycle. Assessments help align your solution to business goals and gauge readiness to

support new technology. Effective planning and design expedite solution adoption. Award-winning

technical support increases operational efficiency and optimization improves performance,

resiliency, stability, and predictability and prepares your network and teams for change. For more

information, visit http://www.cisco.com/go/services.

http://www.cisco.com/en/US/products/prod_warranties_item09186a00805f005b.html

http://www.cisco.com/go/services

Data Sheet


Ordering Information

Table 8 lists ordering information for the Cisco Catalyst 3750-E Series. To place an order, visit the

Cisco Ordering homepage at

http://www.cisco.com/en/US/ordering/or13/or8/order_customer_help_how_to_order_listing.html

Table 8. Cisco Catalyst 3750-E Series Ordering Info

Product Number Product Description

Catalyst 3750-E Series

WS-C3750E-24TD-S ● 24 10/100/1000 ports + 2 X2-based 10 Gigabit Ethernet ports ● 64-Gbps, high-speed StackWise Plus stacking

● 160-Gbps wire rate, nonblocking switching fabric capacity

● Field-replaceable 265WAC power supply and fan tray ● 1 rack unit (RU) stackable multilayer switch ● IPv6 ● IP Base software feature set (IPB)

WS-C3750E-24TD-E ● 24 10/100/1000 ports + 2 X2-based 10 Gigabit Ethernet ports ● 64-Gbps, high-speed StackWise Plus stacking


● Field-replaceable 265WAC power supply and fan tray ● 1 rack unit (RU) stackable multilayer switch ● IPv6

● IP Services software feature set (IPS)

● Provides full IPv6 dynamic routing

WS-C3750E-48TD-S ● 48 10/100/1000 ports + 2 X2-based 10 Gigabit Ethernet ports ● 64-Gbps, high-speed StackWise Plus stacking ● 160-Gbps wire rate, nonblocking switching fabric capacity


● IP Base software feature set (IPB)

WS-C3750E-48TD-E ● 48 10/100/1000 ports + 2 X2-based 10 Gigabit Ethernet ports ● 64-Gbps, high-speed StackWise Plus stacking





WS-C3750E-24PD-S ● 24 10/100/1000 PoE ports + 2 X2-based 10 Gigabit Ethernet ports ● 64-Gbps, high-speed StackWise Plus stacking


● Field-replaceable 750WAC power supply and fan tray ● 420W available for Cisco Enhanced PoE, allowing > 15.4W to all 24

ports ● 1 rack unit (RU) stackable multilayer switch ● IPv6


WS-C3750E-24PD-E ● 24 10/100/1000 PoE ports + 2 X2-based 10 Gigabit Ethernet ports ● 64-Gbps, high-speed StackWise Plus stacking





http://www.cisco.com/en/US/ordering/or13/or8/order_customer_help_how_to_order_listing.html

Data Sheet



WS-C3750E-48PD-S ● 48 10/100/1000 PoE ports + 2 X2-based 10 Gigabit Ethernet ports ● 64-Gbps, high-speed StackWise Plus stacking


● Field-replaceable 750WAC power supply and fan tray ● 420W available for Cisco Enhanced PoE allowing > 15.4W for up to 24

ports

● 1 rack unit (RU) stackable multilayer switch ● IPv6


WS-C3750E-48PD-E ● 48 10/100/1000 PoE ports + 2 X2-based 10 Gigabit Ethernet ports ● 64-Gbps, high-speed StackWise Plus stacking


● Field-replaceable 750WAC power supply and fan tray ● 420W available for Cisco Enhanced PoE allowing > 15.4W for up to 24

ports




WS-C3750E-48PD-SF ● 48 10/100/1000 PoE ports + 2 X2-based 10 Gigabit Ethernet ports ● 64-Gbps, high-speed StackWise Plus stacking





WS-C3750E-48PD-EF ● 48 10/100/1000 PoE ports + 2 X2-based 10 Gigabit Ethernet ports ● 64-Gbps, high-speed StackWise Plus stacking



ports




Catalyst 3750-E Series Product Activation Keys

3750E-LIC=

Catalyst 3750-E Series Product Activation Keys

3750E-IPSLCB-QTY IP Services for 3750-E 24 ports, upgrade from IP Base

3750E48-IPSLCB-QTY IP Services for 3750-E 48 ports, upgrade from IP Base

Power Supplies for the Catalyst 3750-E Series

C3K-PWR-265WAC= Catalyst 3750-E/3560-E 265WAC power supply

C3K-PWR-265WDC= Catalyst 3750-E/3560-E 265WDC power supply

C3K-PWR-750WAC= Catalyst 3750-E/3560-E/RPS 2300 750WAC power supply


Data Sheet


C3K-BLWR-60CFM= Fan Module for the Catalyst 3750-E/3560-E

Redundant Power System for the Catalyst 3750-E Seri es

PWR-RPS2300 RPS 2300

ACC-RPS2300= Spare Accessory Kit

BLNK-RPS2300= Spare Bay Insert

CAB-RPS2300= Spare RPS Cable for Cisco Redundant Power System 2300

CAB-RPS2300-E= Spare RPS 2300 cable

PWR-RPS2300= Spare RPS Cable RPS 2300 Cat 3750E/3560E Switches

BLWR-RPS2300= Spare RPS 2300 Blower



TwinGig Converter Module for the Catalyst 3750-E Se ries

CVR-X2-SFP TwinGig Converter Module

CVR-X2-SFP= TwinGig Converter Module

SFPs for the Catalyst 3750-E Series

GLC-GE-100FX= 100FX SFP on GE SFP ports for DSBU switches

GLC-LH-SM= GE SFP, LC connector LX/LH transceiver

GLC-SX-MM= GE SFP, LC connector SX transceiver

GLC-T= 1000BASE-T SFP

GLC-ZX-SM= 1000BASE-ZX SFP

GLC-BX-D= 1000BASE-BX SFP, 1490NM

GLC-BX-U= 1000BASE-BX SFP, 1310NM

CWDM-SFP-1470= CWDM 1470 NM SFP Gigabit Ethernet and 1G/2G FC








DWDM-SFP-3033= DWDM SFP 1530.33 nm SFP (100 GHz ITU grid)
















Data Sheet


X2 for Catalyst 3750-E Series

X2-10GB-ER= 10GBASE-ER X2 Module

X2-10GB-LR= 10GBASE-LR X2 Module

X2-10GB-SR= 10GBASE-SR X2 Module

X2-10GB-CX4= 10GBASE-CX4 X2 Module

X2-10GB-LX4= 10GBASE-LX4 X2 Module

X2-10GB-LRM= 10GBASE-LRM X2 Module

LC to SC Cables for the Catalyst 3750-E Series

CSS5-CABLX-LCSC= CSS11500 10-Meter Fiber Single Mode LX LC-to-SC Connectors

CSS5-CABSX-LC= CSS11500 10-Meter Fiber Multimode SX LC Connectors

CSS5-CABSX-LCSC= CSS11500 10-Meter Fiber Multimode SX LC-to-SC Connectors

StackWise Cables

CAB-STACK-50CM= Cisco StackWise 50CM Stacking Cable

CAB-STACK-1M= Cisco StackWise 1M Stacking Cable

CAB-STACK-3M= Cisco StackWise 3M Stacking Cable

CAB-STACK-50CM-NH= Cisco StackWise 50CM Non-Halogen Lead Free Stacking Cable

CAB-STACK-1M-NH= Cisco StackWise 1M Non-Halogen Lead Free Stacking Cable

CAB-STACK-3M-NH= Cisco StackWise 3M Non-Halogen Lead Free Stacking Cable

Power Cords for the Catalyst 3750-E Series

CAB-AC Power Cord, 110V

CAB-AC= Power Cord, 110V

CAB-16AWG-AC AC Power cord, 16AWG

CAB-16AWG-AC= AC Power cord, 16AWG

CAB-ACA Plug, Power Cord, Australian, 10A

CAB-ACA= Plug, Power Cord, Australian, 10A

CAB-ACE Power Cord Europe

CAB-ACE= Power Cord Europe

CAB-ACI Power Cord-Italian

CAB-ACI= Power Cord-Italian

CAB-ACR Power Cord Argentina

CAB-ACR= Power Cord Argentina

CAB-ACS Power Cord for Switzerland

CAB-ACS= Power Cord for Switzerland

CAB-ACU Power Cord UK

CAB-ACU= Power Cord UK

CAB-JPN Power Cord-Japan

CAB-JPN= Power Cord-Japan

CAB-IND Power Cord India

CAB-IND= Power Cord India

CAB-C13-C14-AC Power Cord with C14 connector

Spare Rack Mount Kits for the 3750-E Series

RCKMNT-E-1RU= Rack Mount Kit (1RU) for Catalyst 3750-E and 3560-E

Catalyst 3750-E Relicensing for Used Equipment

LL-3750E-IPB= IP Base SW Feature set license for Catalyst 3750-E Series

LL-3750E-IPS= IP Services SW Feature set license for Catalyst 3750-E Series

Data Sheet


For More Information

For more information about the Cisco Catalyst 3750-E Series Switches, visit

http://www.cisco.com/en/US/products/hw/switches/index.html or contact your local account

representative.

Printed in USA C78-377653-07 01/09

http://www.cisco.com/en/US/products/hw/switches/index.html

Documents

Cisco Catalyst 3750-E Series Switches · 2017-08-18 · Cisco TwinGig converter module for migrating uplinks from Gigabit Ethernet to 10 Gigabit ... the Cisco Catalyst 3750-E Series