CL10 (MAY 2012)

7/27/2019 CL10 (MAY 2012)

1/22

PROJECT: Infrastructure buildings of the residential complex (phase 2)

of ITCC complex - RIYADH

REVISED BOQ FOR PARKING CLUSTERS (CL10)

AMOUNT

SR

Soil investigation

The contractor shall implemented of exploratory drilling and Notemechanical test in all types of soil with on site testing and theissuance of the final report which contain the test results andrecommendations of the foundation work.

01 Research and treatment for cavities

Implementation through a perforating exploratory(cavity probing) In 1 M3

all types of rock to determined the horizontal and vertical

elongation of cavities, the contractor will be responsible for

treatment all cavities By injection and treatment for all cavities and

voids of rock with all necessary work accordance with the

technical specifications and instructions of the Supervising

engineer

EXTERNAL WORKS

The bidder is advised to visit the site before quoting the rates in

order to get himself familiarized with the present site conditions

SITE GRADING

Bulk excavate over site on unclassified ground including all hard Note

and rock layers to reduced levels generally in cutting profiles the

work shall include clear away to approved disposals.

All additional excavation required for temporary works and spaces, Note

shoring, dewatering, removal of surplus excavated materials,

support, temporary spoil heaps and general compaction

EXCAVATION AND EARTHWORK

Necessary moving or transportation about the site excavation

material including handling to temporary stockpile or ultimate

disposal off site is to be included in the unit rate of excavation

SITE PREPARATION AND GRADING

02 Excavation oversite on unclassified ground including all hard and 1760 M3

rock layers (if any) to reduced levels generally in cutting profiles

and forming depressions, falls and the like and clear away to

approved disposal tip.

03 Fill oversite with approved imported fill material according to site 7800 M3

soil report recommendation including compaction in making up

levels to required formations, embankments, contouring and the

like as per drawings and spec.

To Collection SR

ITEM D E S C R I P T I O N QTY UNIT RATE

Project No. J10-13300

ZUHAIR FAYEZ PARTNERSHIP

1 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

2/22




AMOUNT

SRITEM D E S C R I P T I O N QTY UNIT RATE

PAVING AND SURFACING

01 Supply and install precast concrete shotblasted pavers with 250 M2photocatalytic titamium dioxide coating (beige color) size

400x400x60mm thk. including 100mm thick cast-in-place concrete

slab with A193-WWF mesh reinforcement, 20mm thick cement

mortar setting bed, moisture barrier on compacted subgrade as per

detail no. A1 on drawing CL10-XL301

02 Supply and install precast concrete shotblasted pavers with 665 M2

photocatalytic titamium dioxide coating (brown and light beige

color) size 400x400x40mm thk. with precast concrete band (light

grey color) size 200x200x40mm including 100mm thick

cast-in-place concrete slab with A193-WWF mesh reinforcement,

20mm thick cement mortar setting bed, moisture barrier,compacted subgrade as per detail no. B12 on drawing CL10-XL301

03 Supply and install precast concrete shotblasted pavers with 1120 M2

photocatolytic titamium dioxide coating ( light beige color) size

400x400x40mm thk. with precast concrete band (light grey color)

size 200x200x40mm including 100mm thick cast-in-place concrete

slab with A193-WWF mesh reinforcement, 20mm thick cement

mortar setting bed, moisture barrier, compacted subgrade as per

detail no. B3 on drawing CL10-XL301

04 Supply and install cast in place concrete with brick band 60mm 200 M2

thick including A193WWF mesh reinforcement, setting mortar bedfor brick, moisture barrier, compacted subgrade as per detail no.

D5 on drawing CL10-XL301

05 Supply and install rubber pavement 50mm thick with various 54 M2

colors, including adhesive mixture, cast in place concrete base with

A193 W.W.F. reinforcement mesh , moisture barrier on compacted

subgrade as per detail no. E6 on drawing CL10-XL-301

06 Supply and install polished granite pavers light beige color size

400x400x30mm including 20mm thick setting mortar bed, 100mm

thick cast in place concrete base with A193WWF reinforcementmesh moisture barrier on compacted subgrad as per detail no. C11 95 M2

on drawing CL10-XL301

To Collection SR



2 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

3/22




AMOUNT


PAVING AND SURFACING

01 Supply and install polished granite paving (brown color) size 718 M2400x400x30mm with granite band (light beige color) size

400x400x30mm including 20mm thick setting mortar bed, cast in

place concrete base with A193WWF reinforcement mesh,

moisture barrier, on compacted subgrade as per detail no. F4 on

drawing CL10-XL-301

02 Supply and install polished granite paving (brown and light 715 M2

beige color) size 400x400x30mm with granite band (grey color)

size 200x200x30 mm, including 20mm thick setting

mortar bed, cast in place concrete base with A193WWF

reinforcement mesh, moisture barrier, on compacted subgrade as

per detail no. F7 on drawing CL10-XL-301

03 Supply and install polished granite paving light beige color size 685 M2

400x400x30mm with polished granite edge paving brown color size

400x400x30mm thick including 20mm thick setting mortar bed,

100mm thick cast in place concrete base with A193WWF

reinforcement mesh, moisture barrier on compacted subgrade as

per detail no. F8 on drawing CL10-XL-301

04 Supply and install polished granite paving light brown and light 745 M2

beige colors size 400x400x30mm with granite band grey color size

200x200x30mm including 20mm thick setting mortar bed, 100mm

thick cast in place concrete base with A193WWF reinforcementmesh, moisture barrier on compacted subgrade as per detail no.

F9 on drawing CL10-XL-301

05 Supply and install polished granite paving beige color size 470 M2

400x400x30mm with granite band grey color size 600x600x30mm

including 20mm thick setting mortar bed, 100mm thick cast in place

concrete base with A193WWF reinforcement mesh, moisture

barrier on compacted subgrade as per detail no. F10 on drawing

CL10-XL-301

06 Supply and install asphalt paving including 80mm bituminous 1955 M2

wearing course, bituminous prime coat, granular base course, oncompacted subgrade as per detail no. G on drawing CL10-XL-301

To Collection SR



3 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

4/22




AMOUNT


CURBS AND EDGING

01 Supply and install Precast concrete curb, size 300X500X150 mm 905 Mwith exposed aggregate finish including bedding, haunching, cast

in place concrete base and concrete grout behind curb, 20mm

thick cement mortar setting bed, on compacted subgrade, as per

detail no.1 on drawing CL10-XL302

02 Supply and install Precast concrete mowing edge, size

200X100X65 mm including concrete base, 20mm thick cement

mortar setting bed, cast in place concrete base on compacted

subgrade, as per detail no. 2 on drawing CL10-XL302 40 M

SUNDRIES

Precast concrete wheel stopper including dowels, grouting

and accessories for complete installation as per detail no. 9

on drawing CL10-XL302 and specification

03 Precast concrete wheel stopper including fixings 16 No.

Wooden Seating

04 Supply and install wooden seating comprising 50x75 mm interior

wood rails, steel sheets, steel straps, including concrete footings,

earthworks, insulation, finishing, fixing, and all required to

complete the work as per detail no.4 on drawing CL10- XL302 3 No.

WOODEN BENCH

05 Supply and install concrete raised planter with wooden bench,

50x75 mm interior wooden rails,comprising concrete walls,

reinforced concrete slab with A 193 W.W.F reinforcement mesh

smooth finished, (Softscape and planting soil mix are measured

elsewhere), drainage layer, filter membrane, water proofing

membrane, protection board, sealant and all required to complete

and finish the work as per detail no.6 on drawing CL010- XL302 to

suit required locations as shown on drawing CL10- XL101 16 M2

To Collection SR



4 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

5/22




AMOUNT


SUNDRIES

Raised Planter

Supply and install concrete raised planter with granite

cladding, including soil mix, drainage layer, filter ,

membrane, sealant and all required to compleet and finish

the work as per detail no. 5 on drawing CL10-Xl302

01 Raised planter, overall area 190 m2 on plan to suit required

locations as shown on drawing CL10- XL101 1 Item

Tent Structure

02 Supply and install tent staructure comprising columns, tent fabric,foundation, earthwork, and all required to compleet and fix the work

as per manufacturer's recommendations and subject to engineer's

approoval to cover an area of 60 m2 as per detail no. 7 on drawing

XL-302 Contractor shall submitt shop drawings for approval before 1 No.

supply

Earth Mount

03 Supply and formation of 6500-1500 mm height earth mount

including compacted sub base layer, 100 mmm thick layer of sand

and gravel mix, and all required to complete and finish te work as

shown on drawing CL10- XL101 and as per detail no. 11 ondrawing CL10- Xl302 1 Item

Softscape and planting soil mix are measured lsewhere Note

To Collection SR



5 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

6/22




AMOUNT


SUNDRIES

WATER FEATURES

Water fountain comprising reinforced concrete wall and

base, ceramic tiles finish, cement mortar setting bed, 30 mm

thick coping, water proofing & mositure barrier, subgrade

compaction, fountain kit, supply and drainage pipework,

fountain pump, electrical power and lighting, installation,

ventilation and exhaust system and all associated works

including builder's work and service installation as per deatil

no.3 on drawing CL10- XL302

01 Water fountain, overall area 46 m2

area on plan, shape as shown

on drawing CL10-XL101. 1 Item


area on plan, shape as shown 1 Item

on drawing CL10-XL101.


area on plan, shape as shown 1 Item

on drawing CL10-XL101.

To Collection SR



6 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

7/22




AMOUNT


SUNDRIES

Manufacturer's standard outdoor sings, letters and plaquesincluding fixings, finishes, accessories complete as per

details on drawing CL10-XL602 and as per specifications

01 Ref. type 1 (DIRECTIONAL SIGN) 2 No.

02 Ref. type 2 (COMMERCIAL CENTER ) 2 No.

03 Ref. type 3 (ADVERTISING PANEL) 6 No.

Manufacturer's standard outdoor sings, letters and plaques

including fixings, finishes, accessories complete as per

details on drawing CL10-XC-05 and as per specifications

04 Ref. type I1 (PARKING) 1 No.

05 Ref. type I2 (ENTRY ) 2 No.

06 Ref. type R2-1 (GIVE WAY ) 1 No.

07 Ref. type R5-1 ( ENTRY PROHIBTED ) 2 No.

08 Ref. type W11-1 ( PEDESTRAIN CROSSING ) 2 No.

Manufacturer's standard outdoor sings, letters and plaquesincluding fixings, finishes, accessories complete as per

details on drawing CL10-XC-04 and as per specifications

09 White stop line 7 M

10 Pedestrain crossing 13 M

11 White edge line 860 M

12 Through traffic arrow 18 M

13 Lane marking205 M

14 Speed control hump including cut & removal of existing wearing 7 M

(0.05m) course & add a new course, tack coat and 0.10m of

bituminous wearing course, ref. 10 detail G

To Collection SR



7 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

8/22




AMOUNT


LANDSCAPING

Trees/palms including pit excavation, stakes and ties, soilplanting mix, mulching, filter membrane and drainage

layer all as details and planting schedule as per detail P1,

on drawing CL10-XL-401

01 P/Wf 12 No.

Trees/palms including pit excavation, stakes and ties, soil

planting mix, mulching, filter membrane and drainage

layer all as details and planting schedule as per detail

P2 on drawing CL10-XL-401

02 T/Af 14 No.

03 T/Bv 9 No.

04 T/Fm 7 No.

05 T/Po 2 No.

Shrubs and ground cover including planting, site excavation

as required, soil planting mix, mulching, filter membrane

and drainage layer all as per details and planting schedule

as per detail P3, on drawing CL10-XL-401

06 S/Iha 56 No.

07 S/Io 13 No.

08 S/Ob 34 No.

09 S/Pav 26 No.

To Collection SR



8 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

9/22




AMOUNT


LANDSCAPING

Shrubs and ground cover including planting, site excavationas required, soil planting mix, mulching, filter membrane

and drainage layer all as per details and planting schedule

as per detail P3, on drawing CL10-XL-401

01 G/Ggp 1088 No.

02 G/Cm ( O ) 747 No.

03 G/Cm (W) 1469 No.

Lawn planting, including soil planting mix, filter membrane

and drainage layer all as per details and planting scheduleas per detail P4, on drawing CL10-XL-401

04 L/Cd 1497 M2

To Collection SR



9 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

10/22




AMOUNT


DIVISION 14 - CONVEYING SYSTEMS

PIPE WORK

Supply and installation of Automated waste collection

system piping. Item shall include the earth works, insulation,

,concentric reducer, puddle flanges ,inspection covers and

all required materials and equipments to complete the

transport pipe line from DV rooms , outdoor load stations and

full vacuum load stations to waste plant.

01 508mm under/above ground transport pipe 75 M

RC MANHOLE

Supply and install cast insitu or precast reinforced concrete

manhole ,the item shall include excavation, backfill

insulation ,inspection cover and all required to complete the

work.

02 RC manhole to suit required location in sitesas shown on drawings 3 No.

STM - ITCCP2 - TD 001 to 016

To Collection SR



10 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

11/22




AMOUNT


DIVISION 15 - MECHANICAL

PLUMBING INSTALLATION

WASTE AND DRAINAGE INSTALLATION

Supply, install and testing pipework, UPVC schedule 40, the

work shall include but not limited to fittings, supports, cast

iron pipes on roof for vent with caps, installation, all

associate works and all materials and equipments required

to complete and finish the work according to drawings,

specification and code of practices

01 50 mm dia. 30 M

02 75 mm dia. 29 M

03 100 mm dia. 115 M

04 150 mm dia. 290 M

05 200 mm dia. 42 M

Accesssories

06 Ground cleanout 50 mm dia, ref. GCO 1 No




10 Grease interceptor 1 No

Construction work for briks inspection chamber, the work

shall include bit not limited to earth work, plain concrete

for foundation BED, concrete channel at chamber DED with

standard cast iron manhole frame and double cover and all

materials and equipments required to complete and finish

the work according to specifications, drawings and code of

practice

11 Inspection chamber, ref. (IC&STIC) 600x600mm 11 No

12 Slow down chamber, ref. (IC&STIC) 600x600mm 2 No

To Collection SR



11 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

12/22




AMOUNT



MANHOLE AND COVERS

Supply , install, testing and commissioning precast

concrete sewer manholes with standard traffic (heavy duty)

type cast iron manhole covers and frames, access ladders,

concrete channel at manhole bed, foundation bed, drop

pipe to manhole where required, all associated earthworks,

damp proofing, and all materals, equipments required to

complete and finish. the work according to specifications

section 02605, 02730, drawings and code of practices

01 Sewer manhole, ref. (SMH) 5 No.

POTABLE WATER INSTALLATION

Supply, install and testing pipework, UPVC Schedule 80 for

potable water the work shall include but not limited to

fittings, supports, all associate works and all materials and

equipments required to complete and finish the work

according to drawings, specification and code of practices

02 25 mm dia. 90 M

03 32 mm dia. 25 M

04 40 mm dia. 20 M

05 50 mm dia. 88 M

06 75 mm dia. 2 M

07 100 mm dia. 90 M

NOT POTABLE WATER INSTALLATION


not-potable water the work shall include but not limited to




08 40 mm dia. 58 M

09 50 mm dia. 84 M

10 63 mm dia. 2 M

To Collection SR



12 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

13/22




AMOUNT



Accessories

01 Water meter assembly 100 mm dia., ref. WMA 1 No

02 Gate valve, 40 mm dia., ref. GV 1 No

03 Gate valve, 100 mm dia., ref. GV 1 No

04 Back flow preventer assembly, 100mm dia., ref. BFPA 1 No

Drainage installation to the external drainage network

Construction work for briks inspection chamber, the work

shall include bit not limited to earth work, plain concrete for

foundation BED, concrete channel at chamber DED withstandard cast iron manhole frame and double cover, UPVC

pipework schedule 40 to nearest main sewer manhole and

all materials and equipments required to complete and

finish the work according to specifications, drawings and

code of practice

05 Slow down chamber 1 No

To Collection SR



13 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

14/22




AMOUNT



IRRIGATION WATER INSTALLATION


Irrigataion water the work shall include but not limited to




01 25 mm dia. 80 M

02 32 mm dia. 87 M

03 40 mm dia. 195 M

04 50 mm dia. 220 M

Accessories

05 Supply and installation irrigation controller as detailed on drwings 1 No.

and as per specifications

06 Supply and installation bubbler for shrubs, ground cover and 569 No.

succulents

07 Supply and installation bubbler for trees and palm tree 188 No.

08 Supply and installation spray lawn sprinkler 46 No.

09 Gate valve W/valve box 32 mm dia., 2 No.



To Collection SR



14 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

15/22




AMOUNT



IRRIGATION WATER INSTALLATION

Supply and installation remote control valve assembly

including piping complete with valve box, Y-strainer,

accessories and all associated works as detail on drawing

and as per specifications section 02810

01 Ref. RCV 25mm dia. 1 No.




DIESEL FUEL STORAGE TANK INSTALLATION

Allow for underground fiberglass diesel fuel storage tank

with required capacity including concrete anti-flotation

pad, heavy duty traffic type manhole ring and cover,

pipework, valves duplex diesel fuel transfer pumps, steel

ladder, pea gravel bed, earthworks, fixings and accessories

all as detailed on drawings

05 Proprietary tank units 1 Item

To Collection SR



15 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

16/22




AMOUNT


DIVISION 16 - ELECTRICAL

MEDIUM VOLTAGE CABLES

Supply , install and test medium voltage Cables

XLPE/STA/PVC 15KVcopper Between RMU unit and

transformers as required to suit the following extensions as

shown on drawings and drawings and as described in

specifications drawings and by making arrangiement with

supervising engineer to achieve the work to the best

possible specifications

01 Medium voltage cable comprising 3 core 70 mm CU / XLPE /STA/ 10 M

PVC, cables route from RMU up to transformers

supply and install Electrical concrete ATTIC including

trenching and backfilling for duct banks, conduits for M.V

cables in duct banks, tapes, all as required to suit locations

as shown on drawings XE-201and as per specifications

section 16180 and by making arrangement with supervising

engineer to achieve the work to the best possible

specifications

02 Electrical concrete ATTIC 32 M

MAIN AND SUB-MAIN POWER

supply and install reinforced concrete Man / Holes connected

via duct banks, complete with man / hand hole bolted type

metal cover, drain pipe outlet, including trenching and

backfilling for duct banks, conduits for M.V cables in duct

banks, tapes, all as required to suit locations as shown on

drawings drawings E201--E220and as all accessories and

coordination & integration with other systems shall be

conducted during work execution as per technical

specificationssection 16180 and by making arrangement with

supervising engineer to achieve the work to the best

possible specifications

Site work

03 Power Hand Holes (900900900) Ref. HH including UPVC conduit 2 No

To Collection SR



16 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

17/22




AMOUNT



POWER CABLES FOR PUMP ROOMS

supply , install, testing and commissioning multicore copper

cable ( XLPE/PVC -1000/600V) in direct buiried including

junction boxes, connection for feeders and various power

loads as shown on drawings E-701 and as per specification

section 16126 and by making arrangement with supervisingengineer to achieve the work to the best possiblespecifications

01 (4 C-16 mm ) + 16 mm G /direct buiried 340 M

PANEL BOARDS FOR PUMP ROOMS

Supply , install , testing and commissioning of panel boards

including grounding, circuit breakers, grounding, fixings,

markers and , other functional units and all associated works

as required and shown on drawings E 701, XE-201

and coordination & integration with other systems shall be

conducted during work execution as per technical

specificationssection 16442,16410,16415 and by makingarrangement with supervising engineer to achieve the workto the best possible specifications

02 Ref. EPP (IP54) 1 No.

03 Ref. PP1(IP 54) 1 No.

04 Ref. PP2(IP 54) 1 No.

To Collection SR



17 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

18/22




AMOUNT



Supply , install, testing and commissioning of power andsockets accessories including all necessary boxes,

faces(according to the engineer approvement ) comprising

cables, conduits, fittings, connections, from the outlets to

Panelboards feeder associated works as required to suit the

locations shown on drawings XE-201and Coordination with

other disciplines shall be conducted during work execution

as per technical specifications, section 16050and by making

arrangiement with supervising engineer to achieve the work

to the best possible specifications

01 Junction box , Floor mounted 10 No.

02 Disconnect switch,non fused and with pilot light16A, 1P, 230V 2 No.,weatherproof for waste collection

03 Disconnect switch,non fused and with pilot light 20A, 1P, 230V 2 No.,weatherproof for feul pumsp

PUMP ROOMS

04 Disconnect switch,non fused and with pilot light 20A, 3P, 400V 1 No.

,weatherproof for fountain pump(FP3)& potable water pump

05 Disconnect switch,non fused and with pilot light 20A, 1P, 230V 5 No.

,weatherproof for submersible pump fountain pump(FP2)&(SP2)

06 Disconnect switch, non fused, 400A, 3P, 400V 1 No.,weatherproof for fire jocky pumps

07 Duplex socket outlet, 13A, 230V, grounding type, weatherproof 3 No

08 Single pole one-way ,one gang switch (13A), weatherproof 1 No.

To Collection SR



18 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

19/22




AMOUNT



LIGHTING INSTALLATION

Supply, install , testing and commissioning of lighting

fixture outlets and including conduits, wires and all boxes

belong to Lighting Panelboards and associated works as

required to suit the locations shown on drawings XE-201

.Coordination with other disciplines shall be conducted

during work execution as per technical specifications,

section 16050 and by making arrangiement with supervising


specifications

PUMP ROOMS

01 Lighting fixer outlet 8 No.

LIGHTING INSTALLATION

Supply ,install, testing and commissioning of lighting

fixture (furnishe with lamp and electronic blast, accessories

and internal wires) mounting accessories.(according to the

engineer approval ) associated works as required to suit the

locations shown on drawings XE-201 ,GE-E01,GE-E01 and

Coordination with other disciplines shall be conducted

during work execution as per technical specifications,section 16500 and by making arrangiement with supervising


specifications

PUMP ROOMS

02 Type F1 4 No.

03 Type F1E 4 No.

To Collection SR



19 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

20/22




AMOUNT



GROUNDING SYSTEM FOR PUMP ROOMS

Supply, installation , test and commissioning of a grounding

system comprising bare copper conductor to bond the

building's distribution boards and HVACand plumping

equipments to the main ear thing grid of the building.

Including necessary earthwork, buried galvanized steel

foundations strips surrounding the building phosphor bronze

test joints & triangular counter poise and all associated

works to suit grounding resistivity required as shown on

drawings XE201 and as described in

specifications16452,16453 by making arrangiement with

supervising engineer to achieve the work to the bestpossible specifications

01 Complete building grounding system network to suit ground 1 Item

resistivity as shown on drawings and specification

To Collection SR



20 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

21/22




AMOUNT



TELECOMMUNICATION SYSTEM

Supply, installation, testing and commissioning of

telecommunication system commporising of

telecommunication outlets including cable / wires and

conduits as shown on drawings E- 501-and as described in

specification section 16715,16720 and by making



To suit system network equipped with:

01Wall mounted telecommunication outlet 1 port (1data ) , ref. (T0)

11No.

weatherproof

FIRE ALARM SYSTEM FOR PUMP ROOMS

Supply, installation, testing and commissioning of Optical

smoke detectors including associated cable wires and

conduiting, interfacing as shown on drawings XE201and as

described in specifications 16721 and by making



To suit system network equipped with:

02 Optical smoke detector Ceiling mounted 3 No.

To Collection SR



21 / 22

REVISED PAGE

Date: MAY 2012

7/27/2019 CL10 (MAY 2012)

22/22




AMOUNT


Collection

Sheet - 1

Sheet - 2

Sheet - 3

Sheet - 4

Sheet - 5

Sheet - 6

Sheet - 7

Sheet - 8

Sheet - 9

Sheet - 10

Sheet - 11

Sheet - 12

Sheet - 13

Sheet - 14

Sheet - 15

Sheet - 16

Sheet - 17

Sheet - 18

Sheet - 19

Sheet - 20

Sheet - 21

To Bill Summary SR

Documents

CL10 (MAY 2012)