807 User Manual

1. PRECAUTIONS

1. Do not expose the camera to moisture, dust, dirt or sandy conditions. Exposing the camera or the lens to these conditions can damage the camera and its components.

2. Do not expose the camera to high temperatures.The normal operating temperature of the camera is 0 to 40 (32F to 104F).℃ ℃High temperatures can shorten the life span of electronic devices, and extremely high temperatures will shorten the battery life and/or degrade the plastic components. Note extreme temperatures can be achieved in parked cars in direct sunlight. Exposing the dash camera to strong sunlight when using Motion Detection mode may cause the camera to malfunction or become damaged as the temperature can be too high in your car in summer or during high temperature conditions.

3. Do not expose the camera to cold environments.Extremely low temperatures can damage electronic components; if there is water or moisture in cold environments, freezing water can cause damage, as thawing. Do not attempt to dismantle or open the casing. Doing so may result in electrical shock and will most likely result in irreparable damage to the camera.

4. Do not mistreat the camera, dropping, sudden impact, and vibration can cause damage to the camera.

5. Do not clean the camera with chemicals, cleaning solution or detergents. Only a damp cloth should be used.

6. Before using the camera, please format the memory cards in the camera or computer to avoid potential camera or card malfunction. Memory cards also need to be formatted regularly to avoid potential camera or card malfunctioning.

7. There may be a layer of plastic film on the LCD screen and the lens, this is intended to prevent any scratching during transportation. Please remove the protective film from the lens before using. Removing the protective film from the screen is optional for the user.

8. The camera uses a built-in super capacitor to get power from the car, due to this the start up time may be a little longer (about 10 seconds). On the first occasion when connected to a computer. The camera may not connect with the computer or the computer may not detect a USB flash. This is normal in the first time instance. If this occurs please remove the plug and then re-plug USB cable to the computer. This will

resolve the issue.

9. The camera will start to record automatically once the car engine is started. The camera is not able to record when the ACC power is on.

2. ACCESSORIES

Before using this product, please make sure that your camera package consists of all the following items. Please contact the distributor in case of any missing components.

Name Quantity Name QuantityCamera 1 piece Car Charger OptionalUSB cable 1 piece 3M Adhesive Label 4 piecesCable Clip 1 bag (6 pieces) User Manual 1 pieceClear Film 2 pieces Lens Cleaning Cloth 1 pieceCPL Filter optional GPS (inside mount) optionalGPU (mount) optional Gift box 1 pieceOBD II cable optional

CPL Filter (optional): Will reduce the reflection from shiny surface like dashboard, sweaty skin, water surface, glass, road, and also let the natural color come through at the same time. Some of the light coming from the sky is also polarized to give a more dramatic sky and high contrast clouds, rendering outdoor scenes crisper with deeper color tones. Align the white line on CPL with the dot on camera to bring the best reflection reducing effect.

Methods of pasting the FILM:1. Spray a small amount of water on the place on your windscreen where the FILM will

be pasted, then use a dry towel to clean it;2. Tear off the FILM, and then paste it to the correct position.3. After you have adjusted the location well, you can use a scratch board or a similar flat

item to stick the film in place and squeeze the water inside out until there is no bubbles or water between the film and the glass.

4. Then place the 3M adhesive label onto the film, then if you need to remove the bracket, it is easy, just remove the FILM.

3. MAIN FEATURES

A: Small and delicate design, easily installed behind the rear view mirror, that will not block your sight, will not affect the safety of driving. If the user wants to check the videos or connect with a computer to check the files, they can remove the camera from the windscreen at any time.

B: This camera uses the best Ambarella A7 DSP chip-set, providing the best high definition video images in low bit rate.

C: We use the most excellent sensor manufacturer, Sony’s latest IMX 322 sensor, best 6G IR lens, to achieve the most perfect effect of low illumination image at night.

D: The user can choose the option to get power from OBD via OBD II cable, to utilize real Parking Guard function.

E: We use a super capacitor for backup power when the vehicle engine is stopped, no battery is inside the camera and provides increased safety over the use of a lithium battery.

F: The camera is equipped with ADAS, (LDWS) Lane departure warning system, (FCW) Forward Collision Warning and (FCMD) Forward collision motion detection, an auxiliary warning system for driving, an additional consideration service for safe driving.

G: CPL filter is optional.

H: Provides real loop recording between two Micro SD cards, support up to 2 x 128GB high speed cards.

I: One button to mute audio and one button to protect video functions. Use the thumb-wheel switch button to control Menu and Playback, both convenient and elegant.

J: Electrostatic Film or 3M glue installation method options are very easy and safe. Users will not need to be concerned with the sticker installation method blocking the driver’s

view or the camera easily dropping off the windscreen and injuring the driver.

Many more surprises in store, please study the user manual to find them.

4. SPECIFICATIONS

CMOS Sensor SONY (1920*1080)Chip Ambarella A7 Display 1.5inchFormat Video:H.264 / Voice:ACC / File:MOVVideo Resolution 1920*1080 30P 16:9 / 1280*720 60P 16:9 / 1280*720 30P 16:9HDMI support

Micro SD card and Formatting warning

Support dual cards, up to 256GB in total, support FAT32 and exfat format, user can choose loop recording. If a card is in use for a long period of time in this camera and has not been formatted, the camera will warn the user to format the card once it is switched on.

GPS track record and playback

GPS Player is built into the camera, supports Baidu and Google maps at the same time.

G-sensor collision video protected

The current video will extend 15 seconds recording when a violent collision occurs, this video will be auto-saved and locked. If the current video time is less than 10 seconds before a violent collision occurs, the previous video will be locked automatically. A maximum of 20 files will be locked. G-sensor data is not to be recorded.

Audio Built-in microphone/ speaker

Loop recording and segment

Segment time: 1min / 3min / 5min / OFF, the card will keep 500MB space free to ensure loop recording will not be interrupted. If the protected files exceed 20 segments, the earliest protected file will be unlocked automatically.

ADAS

LDWS (Land Departure Warning System)FCW (Forward Collision Warning)FCMD (Forward Car Motion Detection)

Recording time If the camera is powered via a car charger, it will always save

after car engine has stopped

the video and turn off immediately, no prolonged video. If the camera is powered by car battery via OBD II cable, default video is 10 seconds, the user can adjust it in the MENU.

When a violent collision occurs, recording time in parking guard mode

If camera is powered by car battery via OBD II cable, default recording time is 15 seconds when violent collision happened. The user can adjust it.

Maximum power consumption 3WParking Guard mode power consumption 1.5WStandby current 12V <6mABattery No battery inside, Camera uses a super capacitor.

5. APPEARANCE

Remarks:1. Thumb wheel SwitchThis switch includes three functions: UP / DOWN / OK

A. UP button: pull thumb-wheel switch upwards1) When camera is in standby, long press UP button for 2 seconds to enter the Menu, long press UP button for 2 seconds again to exit the Menu.2) When in the Playback mode, short press UP button again to enter the sub-menu of Playback; short press UP button again to Playback mode.

3) When camera is recording, short press UP button to turn MIC on or off (mute video). 4) UP button to choose the sub-menu.

B. DOWN button: pull thumb-wheel switch downwards1) When camera is in standby or recording, long press DOWN button for 2 seconds to enter the Video Playback.2) Long press DOWN button again to enter the Photo Playback.3) Long press DOWN button thirdly to exit the Playback.4) DOWN button to choose sub-menu.

C. OK button: push thumb-wheel switch to middle1) When camera is in standby, short press OK button to start recording, short press again to stop recording.2) When camera is in standby or recording, long press OK button to take a photo, screen show “ capture”.3) In the Menu mode or Playback mode, short press OK button to confirm your choice of sub-menu.

2. SOS buttonWhen camera is in standby or recording, long press SOS button to control mute video. When camera is recording, short press SOS button to protect the current video; short press again to unprotected the video. There will be a yellow lock in the screen, and the red lock will blink three times in the screen.

3. Screen buttonWhen camera is standby or recording, you can short press Screen button to turn off the screen, short press again to turn on the screen.Or you can set the power off screen time in the Menu.

4. The other holes are cooling vents.

5. Camera Mounting BracketGPS logger and parking guard board are inside the camera mounting bracket.Place the 3M sticker here and then stick to the vehicle front window.If no GPS and no parking guard option, it is a mounting bracket only, but also can connect car charger with micro USB port 2 to get power from the car.

6. OPERATION

Read this chapter to learn how to operate the camera.

6.1 Turn on /off cameraThis camera does not have an internal battery, it utilizes a super capacitor, so it must be continually connected with the power supply when using.When connected with the power source, the camera will automatically turn on. If no power source, camera will automatically turn off.When the camera is recording or in standby, if the user cuts off the power suddenly, screen will display in red wording “do not power off”.

6.2 Recording Video & Take PhotoWhen the camera is in standby, short press OK button to start video recording;When the camera is recording, short press OK button to cancel video recording.The camera is also pre-configured to auto start recording once it receives power, i.e. when the car engine is started.The camera is also pre-configured to auto stop recording and turn off once it loses power, i.e. when the car engine is stopped.Please notice short press SOS button to protect video when recording.When camera is in standby or recording, long press OK button to take a photo.

6.3 Storage card preparationThe camera supports dual micro SD cards, 2 * 128GB maximum.The files can be stored in card A or card B. The user can insert one micro SD card into the camera or two micro SD cards into camera at the same time, providing more space to store videos, images or other files. Please use high-speed micro SD card meeting the specification of TFHC. (Class 6 is ideal .Class10 may cause some problem because the speed of card is too fast, it is better not use Class10 card)

6.4 Copy function for backup videoVideo clips can be copied manually between card A and card B, then you will have backup after you need to hand over one card to police or the court.1. Please choose card in Playback. 2. When camera is in standby, long press DOWN button to enter video playback or photos playback. Then long press UP button to enter playback sub-menu, you can see COPY FILE TO ANOTHER CARD, options are YES/NO.

3. If you press OK button to choose YES, the OKed video or photo will be copied from this card to another card.4. Please note the user can copy only one video or one photo to another card each time, not all the files.

6.5 Loop recording 1. The camera supports automatic loop recording when the card is full. Here you can set the segment length according to your requirement. If you need continuous video without any segmentation, please set it to OFF but be aware that the maximum video file size is 4GB.2. The camera also supports loop recording between card A and card B, Here you must choose AUTO in choose card (MENU); if choose card A or card B, the videos will be not loop recording between 2 cards, only one card is recording.If user want loop recording between card A and card B, please must make sure the menu as below:A: choose 1MIN / 3MIN / 5MIN of Recycle in Menu, do not choose OFFB: choose Auto of Choose Card in Menu

6.6 Recording Mute Video When the camera is in either standby or recording, you can short press UP button to mute the microphone inside camera at any time; short press UP button again to cancel mute status.When the camera is in either standby or recording, you can long press SOS button to mute the microphone inside camera at any time; long press SOS button again to cancel mute status.

6.7 SOS Manual Protect VideoThe camera supports automatic loop recording which means the oldest video will be over-written by new video when the card is almost full unless the video is protected (read only file attribute).The camera can auto protect videos if the G-sensor data exceeds the configured threshold.You can also manually protect the videos by short press SOS button when recording; short press SOS button again to cancel protected status.If any impact is detected when recording, the current video will be locked automatically.You can also manually protect the video and picture in playback mode.

6.8 Power off ScreenWhen camera is in standby or recording, you can short press SCREEN button to turn off the screen to save power at any time, short press SCREEN button again to turn on the screen.Or you can set it in the MENU.

6.9 Videos and photos playback1. Playback on cameraWhen camera is in standby, long press DOWN button for 2 seconds to enter videos playback; long press DOWN button again for 2 seconds to enter photos playback; long press DOWN button thirdly for 2 seconds to return to standby.When camera is in playback, press UP and DOWN buttons to highlight the video or photo you want to review, and then press OK to view.When the camera is in playback, you can press UP or DOWN buttons to highlight the video or photo you want to edit it, then long press UP button to active the sub-menu. Press UP or DOWN buttons to choose and then OK button to perform the action.

Sub-menu:1. FILE PROTECT OPERATION (protect current file / protect all files / unprotected current file)2. AUTO PLAY (video play one / video play all / video repeat one / video repeat all)3. DELETE FILE (cancel / delete this file / delete all files), protected files can’t be deleted here.4. COPY FILE TO ANOTHER CARD5. CHOOSE CARD If you want to playback videos/photos in card A, please choose card A; if you want to playback videos/photos in card B, choose card B.2. Playback on TV When the camera is connected to a TV via a HDMI cable, the camera screen will be turned off and transfer the display to the TV. The operation will be the same as when using playback on the camera.TV playback is for videos and photos playback only, User cannot make any changes on the sub-menu.(Please make sure camera is connected with the power supply when playback on TV)

3. Playback on computerWhen you wish to review the videos or photos on computer, a micro SD card reader can be used, or you can connect the camera to your computer with the supplied USB cable.GPS PLAYER PROGRAM is placed in the PLAYER folder when a micro SD card is formatted by the camera, which can playback the video recording with GPS traces. You can also use a compatible media player to playback the MOV. video files directly, without the GPS trace.If you connect the camera to your computer with the supplied USB cable. The camera will be recognized as a mass storage device. You can then use the camera as micro SD card readers for two separate micro SD cards for playback.Please notice you need to connect USB cable with Micro USB port 1 in camera when playback on computer, don’t use the Micro USB port 2 in mount.

6.10 Light Indicator

Blue blinking: the camera is in parking mode with low frame rate recording.Red blinking with Blue: the camera is in normal recording mode with MIC on.Red blinking: when in normal recording mode, MIC off; When in parking mode, this means a shock triggered recording.

6.11 Red Light in BracketCar engine is started

6.12 ResetIf the camera is not functioning or frozen, long press the RESET button to reset it.

6.13 ResolutionHere you can choose the video resolution you want to use; higher resolution videos will use more storage space.Options: 1920*1080 30P 16:9 1280*720 60P 16:9 1280*720 30P 16:9

6.14 Quality Here you can adjust the video quality; the quality will affect video grain, sharpness and contrast. Better quality videos will result in higher bit rate and use more storage space.Options: Normal / S.Fine (super fine) / Fine

6.15 AE Meter ModeHere you can set the measuring area for Auto Exposure; this setting will affect the video brightness and quality. CENTER is recommended if there is no special requirement.Options: Center / Average / Spot

6.16 WDR (Wide Dynamic Range)Options: ON / OFF

6.17 ADAS Detect / ADAS Calibration ADAS: LDWS (Land Departure Warning System) FCW (Forward Collision Warning) FCMD (Forward Car Motion Detection) Options: ON / OFF

6.18 FlickerHere you can set the sensor flicker frequency to fit your AC power frequency and reduce the effect of flickering lamps. Please leave in AUTO if you are not sure which frequency is in use in your country.Options: Auto / 60hz / 50hz

6.19 White Balance

Here you can set the image white balance mode to improve color balance in videos / images for different weather and lighting conditions. Auto is recommended to fit most conditions.Options: Auto / Sunny / Cloudy / Tungsten / Fluorescent

6.20 Exposure Values (EV)Here you can manually adjust the Exposure Values (EV) to improve the image brightness.Options: 0 / +0.3 / +0.7 / +1.0 / +1.3 / +1.7 / +2.0 / -2.0 / -1.7 / -1.3 / -1.0 / -0.7 / -0.3

6.21 RecycleThis camera supports automatic loop recording when the card is full. Here you can set the segment length according to your requirement. If you need continuous video without any segmentation, please set it to OFF, however be aware that the maximum video file size is 4GB and the camera will stop recording once the card is full.Options: 1 MIN / 3 MIN / 5 MIN / OFFPlease notice if user want to make loop recording between card A and card B, here can ’t choose OFF, otherwise, only one card is recording, the other card will never start to record video even you choose AUTO of Choose Card in Menu.

6.22 Motion Detect Motion detection is used to reduce the amount of storage space used. When there is no obvious motion detected the camera will switch to standby. Once motion is detected above the threshold value, the camera will start recording and continue for 15 seconds after the motion stops. Options: OFF / ON

6.23 Time SetupHere you can set the Time Zone, system date and time manually. The date/time information will be automatically updated if GPS satellites are connected. 00 2015 / 01 / 01 12:12 Time zone Date TimeThe time zone, corrected for daylight saving time, will need to be set before the GPS signal can correctly update the time.

6.24 Power off ScreenWhen camera is in standby or recording, you can short press SCREEN button to turn off the screen to save power at any time, short press SCREEN button again to turn on the screen.Or you can set it here, options are OFF / 10 sec / 20 sec / 30 sec.

6.25 StampHere you can stamp information on video.

Options: OFF / Date Time / Driver Number Stamp

6.26 Drive NumberHere you can define the driver number or your customized information to stamp on the video (9 characters or numbers).

6.27 GPS StampThe camera can record your driving track and stamp the GPS data on video.Here you can define the GPS data stamping method. Please note there maybe electronic interference on GPS signal from camera, radar detector, wireless transmitter, hardwire kit, car charger, or other devices; which will delay the GPS connecting or create errors in the GPS data. An external GPS antenna will help to enhance the reliability.Options: OFF / ON

6.28 Speed StampHere you can set the Speed stamp.Options: OFF / ON

6.29 G-sensor SensitiveThe G-sensor is used to detect the 3-axis impacting forces. If any impact over the threshold value is detected. The current recording file will be locked / protected to avoid being over-written. Here you can define the sensitivity threshold value.Options: CLOSE / LOW / MEDIUM / HIGH

6.30 GPS (see 6.40)Options: ON / OFF

6.31 Speed UnitOptions: Km/H / MpH

6.32 Parking Guard Mode (see 6.41)Options: Low frame mode / normal mode / OFF / Pre-record mode

6.33 Senior Setting

6.34 Beep SoundHere you can set the beep sound.Options: ON/OFF

6.35 LanguageHere you can set the language you prefer.Options: English / 简体中文 / 繁體中文 / Русский

6.36 Default Setting

Here you can restore all the settings to the factory default settings.Default setting in Menu, options: NO / YES

6.37 FormatBefore using, please format the cards in the camera or computer to avoid any unnecessary issues. Please check the card icon shown (card A or card B) on screen or choose card (card A or card B) in the Menu carefully before formatting, all files will be lost once you start the formatting process. After a period of time, we suggest users format the cards regularly.(If you are using micro SD card larger than 32GB, please format the cards on a computer to be FAT32 format)Options: NO/YES

6.38 Choose CardHere you can choose the card which you want to store the videos and photos on.Options: Auto / CARD A / CARD BIf there is only one card in camera body, this card will store videos and photos by default.If there are two cards in camera body, 1. Here choose Auto, loop recording between card A and card B. Please make sure you do not set Recycle of Menu to OFF, otherwise once the recording card is full, the other card will not start to record.2. If CARD A or CARD B is chosen, only CARD A or CARD B will store videos and photos, there will be no loop recording between two cards. There is another choice in card sub-menu in playback, not the same as here.

6.39 Firmware versionHere you can find the current version of the firmware in your camera.You may need this information when you are trying to upgrade the camera to a later firmware. Firmware update process:1. Copy firmware (bin) file into Micro SD card.2. Insert Micro SD card into camera and turn on the power, please make sure camera is connected with the power during the process.3. Wait for several seconds, “firmware update”? YES, NO” to appear on the screen, Then choose YES to update it. The camera will automatically update the firmware, the complete process will takes approximately 1 minute.

6.40 GPS GPS trackerThe camera can record your driving track and stamp the GPS data on video. You can define the GPS data stamping method. Options: OFF/ONIf you want to use GPS function, please make sure car charger connected with the micro

USB slot 2 in the GPS (bracket), not the micro USB slot 1 in the camera body.Please note there maybe electronic interference on GPS signal from camera, radar detector, wireless transmitter, hard wire kit, car charger, or other devices; which will delay the GPS connecting or create errors in GPS data, GPS signal will be very weak under the bad weather conditions.

GPS playerBefore playing the GPS tracker, user needs to download GPS player QTPLAYER application onto your computer, directions are as per below:1. Insert your micro SD card into camera; the camera system will copy the GPS player

to your SD card automatically.2. Connect your camera to computer, find [Player] file, double-click the

to start the player. At the same time, it will jump out a window

as below, please choose YES to download the Quicktime. You will need to install the driver (named Quicktime) before using. (You can also visit Quicktime website to download it directly: http://www.apple.com/quicktime/download/)

Please click the red arrow words: 1. Previous Versions of QuickTime for Mac and Windows2. QuickTime 7.7.6 for Windows3. Download

3. After download, find the Quicktime driver , double-click

to install. 4. After installing the Quick time onto your computer, now you can go back to the micro

SD card and use the GPS player now.

5. click to import files from camera, use or to check for more files.

Player Icon:

Open the video file form here

Remarks: If user uses to play the video directly, it will not display GPS track.

So we suggest user copy all PLAYER file from micro SD card to computer, and play the

videos on , this way, all of the GPS information will be displayed.

6.41 Parking Guard (optional)(OBD power supply and how to use parking guard function)

1) When using Parking Guard Function , only use the OBD II cable to get power from the car battery. connect the OBD II cable with the OBD hole in mount and plug it into the vehicles OBD port for use. It is very easy and convenient.

Please note that you cannot use car charger for parking guard function. Remove the Micro USB cable from GPS box bracket when using parking guard function.

2) In the OBD power supply mode, built-in CPU will auto-detect whether the car engine is started. If the car engine is detected, the camera will start recording.

3）if the car engine is stopped, the camera will be in Parking Guard modes, there are 4 modes in this status, user can choose one of them. (choose it in camera menu, the default is B):

A: Normal mode: camera will not record after parking, like using car charge .

B: Low Frame mode: When parking, camera will start loop recording in lowFps status (1fps/second). Once unexpected shocks or collision is detected, camera will auto start to record a normal fps  emergency video immediately, and this video file will be locked automatically. camera will go back to low fps recording if the crisis is resolved. (advantage: under this mode, the whole course will be recorded when parking).Parking guard function with Time Lapse for monitor your car perfectly when parking under low FPS monitor mode.                               

C: Prerecord mode: No low frame record ,Once unexpected shock or collision is detected, the camera will save and lock one video, The video is  before and after violence collision.(advantage: under this mode, Car owner know what happen before and after shock or collision happened . One more is the Micro SD card’s life will be extended )                               D: OFF: like NORMAL mode.

4) When the voltage of car battery falls below safe starting voltage, camera power will be cut off power automatically, enter the standby mode, under this mode, camera uses almost no power. User can set the safe voltage in the senior setting, default setting is 11.5V.

5) Parking Guard and other settings:

A: Firstly, connect car charger to charge the camera, turn on it, long press UP key to enter MENU, set Parking Guard mode, save and exit MENU.

B：Use OBD II cable connect camera to parking guard hole in GPS bracket and remove the car charger from micro USB port. The camera will automatically turn on once the car engine is started. Please press OK key to stop recording, under standby mode.

6）Parking Guarding parameter setting as below：

Items FunctionsDefault Settings

Function Descriptions

1 Parking Guard ModeNormal Mode

As above

2Collision detection sensitivity when the car engine is stopped

Middle

3Recording times after violent collision occurs

15 seconds

4Recording times after car engine is stopped

15 seconds

5Collision detection sensitivity when the car engine is starting

Middle

6Voltage of car battery when car engine was started

13.3V

When the car engine is started, automotive alternator charge to car battery voltage is 13.3V. If the car battery voltage more than 13.3V, it means the car is start and camera will be in recording mode. Different cars, different battery ageing situation, then different voltages, 13.3V is the most common voltage. In Parking Guard mode, start the car engine, if the camera doesn’t record, maybe the voltage is a little higher than the actual value; if the camera does not stop recording automatically after car engine stop, maybe this voltage is a little lower than the actual value, user may need to make adjustment.

7 The lowest voltage of car engine starting

11.5v If car battery voltage falls below 11.5V, camera cannot receive power from the OBD,

camera will be turned off automatically, Parking Guard function will not work at the same time, too ensure the car engine will start will normally.

7. POWER SOURCE

The camera can be powered by power lead for cigar lighter socket (standard accessory), or OBD II cable (optional accessory).

1. Power lead for cigar lighter socket is an easy and fast connecting method for camera, user only needs to plug the power lead into the cigar socket in the car. The camera will be powered once the engine is started. The disadvantage of power lead for cigar lighter socket is it will occupy your cigar lighter socket and may create alignment difficulty for the long cable.

2. Please connect the car battery with the round hole in GPS (bracket) via OBD II cable.

When using parking guard function, camera must use OBD II to get power from car, do not use the car charger.

8. MOUNTING

The camera is designed for easy & quick mounting to your windshield with the VHB sticker pad.

1st, mount the camera to the mounting bracket with power cable plugged into either the mount or camera body;

2nd, simulate the unit on your windshield with the camera powered on, rotate the camera vertically to find the best mounting location;

3rd, clean and dry your windshield, put the film on it. Stick the VHB sticker pad to the mount bracket or wedges, and attach it to the film to your windshield, hold the mount for

a few seconds to ensure good adhesion;

4th, power on the camera and check the camera display again.

When you want to demount the camera, just slide the camera out from the mounting bracket; no need to take the mounting bracket down.

If you want to change the location, just remove the film, take the camera and bracket down, it is very convenient.

Please don’t break off the mount bracket from windshield with a rigid crowbar, this may damage the mount bracket or your windshield.

The recommended mounting location for camera is at the center of the windshield, just behind the rear view mirror. That is the most invisible location to hide the camera, and will not interrupt you when driving.

9. PC SYSTEM REQUIREMENTSWindows XP or later operating system, MAC 10.1Intel Pentium 4 2.8Ghz CPU or above (recommended 3GHz)At least 2GB RAM or above (recommended 4GB）Internet connection (for GPS log playback)

10. UI ICON and STATEMENT

11. TROUBLESHOOTING

● Cannot record video or take picturePlease check that there is enough storage space on the micro SD card. Or if you have Loop Recording on that the files are not all protected (read only attribute).

● camera stops recording occasionallyBecause the data stream of high-definition video is huge, please use a high-speed Class 6 or Class 10 micro SD card that compatible with SDHC.

● “File Error” prompt while playback the video or imageCorrupt data storage results the file error, please use the “FORMAT CARD” menu to format the micro SD card. (Please format the card on a computer to be FAT32 format if it is bigger than 32GB).

● No image display on TV screenPlease confirm the HDMI cable is connected correctly, and the TV is set to the correct HDMI mode.

● Image is blurredMaybe the lens or windshield is not clean; please check if there is dust, fingerprint, or something else on the leans. Use leans cleaner to clean the leans before using. Please remember to remove the lens protecting film before first use.

● Image has horizontal stripes interferenceThis is due to the wrong setting of “Flicker”, please adjust it depending the local power supply frequency, and reset the Flicker: 50Hz / 60Hz.

● Camera doesn’t auto start recording when the car engine is started.Please make sure the Movie Clip Time is 1 / 3 / 5 minutes, not OFF, it will not auto start recording when Movie Clip Time is OFF; Additionally, please check if the micro SD card is full; if yes then please try to format the micro SD card.

● The camera continues automatic recording and won’t stopMaybe the camera is working on Motion Detect mode; you can check whether there is an icon on the screen. When the Motion Detection is ON, it will auto start recording when a moving object appears within the range of camera. When the motion ceases, the recording will stop automatically until a moving object appears again. It is not

easy to turn Motion Detection function off with the camera in hands.

● Auto Power Off setting doesn’t workPlease ensure that motion detection is turned off. If the motion detection is on, the camera will always be in standby mode (it will start recording when it sees a moving object), the camera will not automatically shut down until the power goes off.

● If the camera has locked up and will not respond to button presses?Remove the camera from the mount or turn off the power, then press the RESET button to reset it.

● The camera is suddenly turned offTurn on again the camera, connect with the power.

● Memory card cannot be usedRemove the memory card.Or format the memory card, before formatting; make sure to backup files first.

● Power indicator doesn’t workPlease check the power line OK or not.

For more questions, please contact seller.

About the Manual We have tried to ensure that what is in this manual is correct and up to date. However, we cannot guarantee that all content is correct without any errors. If there is a variance between the manual and camera, please accept the camera standard as correct. We reserve the right to change content or technical regulations without informing you prior to making any changes. In addition, the manufacturer reserves the right to change technical specification without informing you prior to making any changes.If the accessories listed differ from the ones included with the actual product, please accept the actual product as standard and correct.