Upload
phamkhuong
View
214
Download
0
Embed Size (px)
Citation preview
COLOR DOME TYPE CAMERA
680TVL /WDR
MANUAL
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with limits for a
Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform
to all local codes
3
1. Features --------------------------------- 4
2. Precautions --------------------------------- 5
3. Cable Connection & OSD Control --------------------------------- 6
4. Camera Operation --------------------------------- 7
5. Troubleshooting --------------------------------- 15
6. Dimensions & OSD Board --------------------------------- 16
7. Specifications --------------------------------- 18
■ Contents
4
■ 1/3" 520K/610K Sony Double Scan CCD II
Minimum Resolution 0.1 Lux (F1.2, 50 IRE), S/N Ratio 52dB
■ High Resolution 680 TV Lines
This camera has realized high resolution of 680 TV lines using the top-notch full digital
image processing, 12 Bit A/D serial signal processing and special algorithm technologies.
■ DNR (Digital Noise Reduction, 2D+3D)
The DNR technology eliminates noise thus generating a distinct and clear image.
■ DAY&NIGHT (Output the Filter changing signal)
This camera has the Day/Night function which outputs the filter changing signal with
detecting the illumination condition.
Day/Night operation feature is an ‘auto’ mode which switches between day and night mode
automatically based upon the level of illumination on the scene.
EXT mode changes between day and night operation upon triggering from an external
Source (Optional). And also, the COLOR mode operates in daytime conditions to provide
optimum colors, and B/W mode operates in night-time conditions to enhance the definition
of the image.
■ OSD (On Screen Display)
This camera supports the OSD function which is used with multi languages. And so, the
camera can be controlled by selecting text displayed on the monitor screen.
■ WDR (Wide Dynamic Range)
This camera function is to produce a clear and balanced image by capturing both the
bright and dark areas of the camera view. In essence, it can process a wide range of light
by minimizing saturation from areas of direct sunlight and enhancing darker indoor areas.
■ SENS-UP
This camera automatically detects the ambient level of darkness in the dark or low contrast
scene to extend the accumulated time, keeping the image bright and sharp.
IN CASE OF IR CAMERA
☺Smart IR
If IR indicator turns on, this camera switches to IR mode for preventing an object from
being too bright, which helps you identity the object in near distance.
☺Visibility: 30m
In B/W mode , the IR indicator turns on with the effective visibility of 30m at 0 Lux
1. Features
5
Only use the camera under conditions
where temperatures are between
-10°C and +50°C. Be especially
careful to provide ventilation when
operating under high temperatures.
It can cause the image quality to be
poor.
Severe lighting change or flicker can
cause the camera to work improperly.
It is one of the most important parts of
the camera. Be careful not to be stained
by fingerprint.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that
corrode the electronic components.
If it is exposed to radioactivity,
For heated CCD, it will be out of order.
It can damage the CCD.
It can cause malfunctions to occur.
2. Precautions
6
1) Cable Connection
2) OSD Control
- SETUP button : Used for the menu display. This button can be used to confirm
settings after changing the value of the selected function or current conditions.
- UP & DOWN buttons : Used for selecting items by moving the cursor up or down on
the menu screen.
- LEFT & RIGHT buttons : Used when changing item values, by moving the cursor to
the left or right on the menu screen
3. Cable Connection and OSD Control
7
Please press the SETUP button, Settings can now be made. The SETUP menu is
displayed on the monitor. Please select any function you wish to activate by using the UP
and DOWN buttons. The arrow can be moved up or down by using the UP and DOWN
buttons. Please position the arrow to point to the function you wish to operate.
■ LENS
The function is used to set the mechanical iris of
the lens.
▶AUTO / MANUAL
■ EXPOSURE
The function is used to adjust camera Exposure.
▶BRIGHTNESS (0~255)
Set the screen brightness
▶SHUTTER
(1/60(1/50),1/100(1/120),1/250,1/500,1/1K,1/2K,
1/4K,1/10K)
Set the shutter speed
▶FLICKERLESS (ON/OFF)
Sets the screen flickerless
▶AGC (0~255)
Set the AGC value
▶SENS-UP (OFF,x2,x4,x8,x16,x32,x64,x128,x256,x512)
Set the screen Sens-up
4. Camera Operation
4. Setup Menu Operation
SETUP MENU 1/2
LENS AUTO
EXPOSURE
PICT ADJUST
WHITE BAL ATW
WDR OFF
HLC/BLC
DNR
EXIT SAVE
EXPOSURE
BRIGHTNESS 024
SHUTTER 1/50
FLICKERLESS OFF
AGC 008
SENS-UP AUTO X4
SPEED 063
RETURN
8
■ PICT ADJUST
The function is used to set the image adjustment
terms.
MIRROR
(OFF/V-FLIP/H-FLIP/HV-FLIP)
Set the horizontal flip for display output.
CONTRAST (000 – 255)
Set the screen contrast.
SHARPNESS (000 – 255)
Set the screen sharpness.
■ WHITE BAL
This function is used to set the white balance operation mode.
▶ATW
Auto tracking white balance
SPEED (0~255): Adjust the pull-in speed ATW
DELAY CNT (0~255): Set the time-based
hysteresis of ATW
ATW FRAME (x0.5, x1.00, x1.50, x2.00): Set the
pull-in frame magnification
ENVIROMENT (Indoor, Outdoor): Set the pull-in
frame of ATW.
▶PUSH: All pull-in
PICT ADJUST
MIRROR OFF
CONTRAST 032
SHARPNESS 010
HUE
GAIN
RETURN
GAIN
AREA 1
RYGAIN 141
VYGAIN 192
RETURN
HUE
AREA 1
RYHUE 212
VYHUE 054
RETURN
GAIN
Adjust the gain. AREA(1~4),
RYHUE(0~255), BYHUE(0~255)
HUE
Adjust the hue.
AREA(1~4), RYHUE(0~255),
BYHUE(0~255)
ATW SETUP
SPEED 245
DELAY CNT 003
ATW FRAME x2.0
EVVIRONMENT INDOOR
RETURN
9
▶USER1
Outdoor fixed gain
B-GAIN: Used for operating the Blue gain in the
WB fixed gain mode.
R-GAIN: Used for operating the Red gain in the
WB fixed gain mode.
▶USER2
Fluorescent light fixed gain
B-GAIN: Used for operating the Blue gain in the
WB fixed gain mode.
R-GAIN: Used for operating the Red gain in the
WB fixed gain mode.
▶ANTI CR: Color rolling suppression
▶MANUAL
Manual white balance
Set the B and R gain values for manual WB
▶PUSH LOCK: Hold
■ WDR
This function is used to set Wide Dynamic Range compensation.
▶OFF: WDR compensation OFF
▶ON: WDR compensation ON
LEVEL: LOW/MID/HIGH
■ HLC/BLC
The function is used to set the High Light compensation and Back light compensation.
USER1 WB
B-GAIN 029
R-GAIN 050
RETURN
USER2 WB
B-GAIN 045
R-GAIN 038
RETURN
USER2 WB
LEVEL 019
RETURN
10
HLC: ON/OFF
CLIP LEVEL (0~255)
SCALE (0~255)
BLC: ON/OFF
※ When the WDR is ON, the BLC is not
working and when the BLC is ON, the HLC is
not available.
■ DNR
The function is used to set the Digital Noise
Reduction.
LEVEL:
OFF/LOW/MIDLOW/MID/MIDHIGH/HIGH
Set the DNR strength.
■ DAY/NIGHT
The function is used to set the Day/Night
function.
▶AUTO: Day or Night is automatic
DELAY CNT (000 – 255): Set the Night/Day
identification transfer time
DAY ---> NIGHT( 000 – 255): Set the threshold
for identifying the Night status from the Day
status.
NIGHT --> DAY(000 – 255):Set the threshold for
identifying the Day status from the Night status.
SMART IR (OFF/ON)
When the SMART IR is ON, the MODE and
LEVEL should be set.
LEVEL: Set sensitivity of the IR
MODE: The AUTO will be work automatically
and the CENTER must be set SMART IR AREA
by user as follows.
HLC/BLC
HLC OFF
CLIP LEVEL 010
SCALE 012
BLC OFF
RETURN
DNR
LEVEL MIDLOW
RETURN
DAY/NIGHT SETUP
DELAY CNT 005
DAY→NIGHT 005
NIGHT→DAY 075
SMART IR OFF
RETURN
SMART IR
MODE CENTER
LEVEL 015
RETURN
11
SMART IR AREA
TOP (1~136), BOTTOM (1~144)
LEFT (1~223), RIGHT (1~239)
▶COLOR: Color only
▶B/W: Only b/w
BURST (OFF): Burst signal OFF
BURST (ON): Burst signal ON
SMART IR (OFF): SMART IR OFF
SMART IR (ON): SMART IR ON
▶EXT1: External Input1
▶EXT2: External Input2
▶CDS: External CDS Input
DELAY CNT (000 – 255): Set the Night/Day
identification transfer time
DAY ---> NIGHT (000 – 255): Set the threshold
for identifying the Night status from the Day
status.
NIGHT --> DAY (000 – 255): Set the threshold for
identifying the Day status from the Night status.
SMART IR (OFF/ON): Set the threshold for
detecting IR lighting.
SMART IR AREA
TOP 037
BOTTOM 106
LEFT 064
RIGHT 176
RETURN
B/W
BURST OFF
SMART IR OFF
RETURN
CDS
DELAY 000
DAY→NIGHT 000
NIGHT→DAY 000
SMART IR OFF
RETURN
12
■ DZOOM / DIS
The function is used to set the digital zoom factor and position.
Digital Image Stabilization will set the anti-shake
compensation.
▶DZOOM(DIGITAL ZOOM)
RATIO (000 – 255): Enlarge the screen with
DIGITAL ZOOM.
PAN (000 – 255): Move the screen left and right
in D-ZOOM setting
TILT (000 – 255): Move the screen up and down
in D-ZOOM setting
▶DIS(DIGITAL IMAGE STABILZATION)
ON/OFF
■ PRIVACY
The function is used to set up to eight privacy
masks.
AREA SEL:
1/15,2/15,3/15,4/15,5/15,6/15,7/15,
8/15,9/15,10/15,11/15,12/15,13/15,
14/15,15/15.
Select the mask frame to be adjusted
MODE
Set the privacy zone to ON or OFF
POSITION
Set the mask frame selected by the AREA SEL parameter.
COLOR
BLACK, RED, GREEN, BLUE, YELL, OW, CYAN, MAGENTA, WHITE.
Set the colors of the mask frames
TRANSP (0.00, 0.50, 0.75, 1.00)
Set the transparency ratio of the mask frames.
MOSAIC (OFF/ ON)
Set the mask frame mosaic to ON or OFF
DZOOM/DIS
RATIO 000
PAN 512
TILT 256
RETURN
PRIVACY
AREA SEL 1/15
MODE OFF
POSITION
COLOR
TRANSP
MOSAIC
RETURN
13
■ MOTION ON
The function is used to set the motion detection
operation.
DETECT SENSE (000 – 127): Set the motion
detection sensitivity
BLOCK DISP: Control the ON/OFF status of the
motion detection block display
DETECT AREA: Set the motion detection area
MONITOR AREA: Set the Monitoring frame
AREA SEL
1/4(Monitoring frame 1), 2/4(Monitoring frame 2)
3/4(Monitoring frame 3), 4/4(Monitoring frame 4)
MODE (OFF/ON )
Control the ON/OFF status of the motion
detection block display
TOP (000 – 015)
Set the top side of the monitoring frame selected
by the AREA SEL parameter.
BOTTOM (000 – 015)
Set the bottom side of the monitoring frame
selected by the AREA SEL parameter.
LEFT (000 – 023)
Set the left side of the monitoring frame selected by the AREA SEL parameter.
RIGHT (000 – 023)
Set the right side of the monitoring frame selected by the AREA SEL parameter.
MOTION
DETECT SENSE 111
BLACK DISP OFF
DETECT
MONITOR AREA
RETURN
MOTION AREA
AREA SEL 1/4
MODE OFF
TOP 002
BOTTOM 006
LEFT 003
RIGHT 009
RETURN
14
■ CAMERA SET
The function is used to set the camera Title and
communication.
TITLE (OFF/ON)
Camera TITLE display ON/OFF
SYNC
INT The current synchronization mode
VERSION
Camera VERSION displays.
■ LANGUAGE (Multi Language)
The function is used to select the language in which to display the internal OSD menu.
■ EXIT
SAVE "◀" "▶" All the settings of the internal OSD menu are saved
NOT SAVE "◀" "▶" All the settings of the internal OSD menu are not saved
CAMERA RESET "◀" "▶" All the internal OSD menu settings are initialized
CAMERA SET
TITLE OFF
SYNC INT
VERSION
RETURN
15
If there are problems in operation, please refer to the items below. If the problem persists,
please contact the agent you purchased this product from.
Problems Troubleshooting
Nothing appears on the screen.
• Please check the power connection.
• Please check the video signal line connection.
• Please check and make sure that the auto lens switch is
set to DC (VIDEO) when using a VIDEO(DC) lens.
The video image is not clear.
• Please check if the lens is clean.
Please clean the lens with a clean cloth or brush.
• Please adjust the contrast feature of the monitor.
• Please readjust the back focus of the camera.
The screen is dark.
• Please adjust the contrast feature of the monitor.
• If you have an intermediate device, set the 75 / Hi-z
properly, and check the terminals.
• Please check if an auto iris lens is being used and adjust
the brightness level.
There is a problem with the
camera operation.
• Please check if an appropriate power source to the
camera complies with the manufacturer's
standard requirement, or if the voltage keeps changing.
The MOTION DETECTION function
is not working.
• Please check if 'MOTION DETECTION' mode is turned
on.
• Please check if the MD LEVEL is too low.
• Please check the setting of the MD AREA.
Colors are not quite right. • Please check the 'WHITE BAL' setting
The screen is flickering.
• Please check if the camera is facing directly into sunlight
or fluorescent light.
• Please check if an auto iris lens is being used.
• Please check the connection of the lens connector cable.
COLOR mode is not working. • Please check if the AGC menu is set to the OFF
position.
SENS-UP function is not
working.
• Please check if the AGC menu is set to the OFF
position.
• Please check if the SHUTTER menu is set to
MANUAL mode.
5. Troubleshooting
16
DOME CAMERA
N1
N2
N3
6. Dimensions & OSD Board Configurations
17
N4
VANDAL DOME CAMERA
N5
N6
18
IR VANDAL DOME CAMERA
N7
19
▪ GENERAL
MODEL WDR CAMERA
Signal system NTSC PAL
Image Sensor 1/3” 960H double Scan Sony CCD∥
Total Pixels 1028(H)X508(V) 1028(H)X596(V)
Effective Pixels 976(H)X494(V) 976(H)X582(V)
Resolution Max. 680 TV lines (B/W 750 TV Lines with ICR)
Scanning Frequency 15.734KHz(H), 60Hz(V) 15.625KHz(H), 50Hz(V)
Shutter Speed 1/60~1/10,000 sec 1/50~1/10,000 sec
Min. Illumination Color: 0.1Lux(50IRE) / B/W:0.00003Lux (Sens-up 512x)
Day & Night Day / Night / Auto / EXT (Option: True Day & Night with ICR)
OSD English/Japaness/German/French/Russian/Portuguese/Spanish/Chinese
ATW 1800~10500K
AGC Level setting
BackLight BLC / WDR (60dB)/ HLC
White Balance ATW/PUSH/USER1/USER2/ANTICR/MANUAL/PUSH LOCK
DNR Off / 3D(Y 0-15)
Privacy Zone / Motion 15 Areas / 4 Areas
Camera ID OFF/ON
S/N Ratio More than 52dB
Video Output Composite video output 75 ohm terminated
Lens
3.6 mm Fixed Lens
2.8~12mm Auto Iris Lens ( TDN: Option )
9~22mm Auto Iris Lens
4~9mm Auto Iris Lens
mm
Sync. System Internal
Operating Humidity 30 % ~ 90 % RH
Operating Temp. - 10°C to 50°C
Dimension 61(W) X 55(H) X 104.7(D)mm
Power Consumption Max 1.8W
Power Supply DC 12 V(10.2V~14.5 V), Dual Voltage(Option) : AC24V / DC12V
7. Specifications
20
Dome type
Vandal dome type IR Vandal Dome
Number 1 2 3 4
Install Type Indoor Indoor Indoor Indoor
Dimension(mm) 100x76.5(H) 120x95(H) 100x103(H) 81x87(H)
3 Axis 2 Axis 2 Axis 3Axis 3Axis
Material Plastic Body &
Bubble
Plastic Body &
Bubble
PC Bubble &
Plastic Body
PC Bubble &
Plastic Body
Weight 300g 560g 600g 300g
Power
Consumption Max 1.8W Max 2.5W Max 2.5W Max 2.5W
Power
Supply
DC12V
(10.2V~14.5 V)
DC 12 V 500mA(10.2V~14.5 V)
Dual Voltage(Option) : AC24V / DC12V
Number 5 6 7
LED x x 30LEDs(750nm)
Visibility Range x x 30m
Install Type Outdoor/Indoor Outdoor/Indoor Outdoor/Indoor
Dimension(mm) 100 x 145(H) 100 x 144.4(H) 100 x 144.4(H)
3 Axis 3 Axis 3Axis 3 Axis
Material Aluminum Body
& PC Bubble
Aluminum Body
& PC Bubble
Aluminum Body
& PC Bubble
Weight 560g 600g 650g
Power
Consumption Max 2.5W Max 2.5W Max3.5W
Power Supply DC 12 V (10.2V~14.5 V)
Dual Voltage(Option) : AC24V / DC12V
21