Upload
others
View
7
Download
0
Embed Size (px)
Citation preview
Computer SMART III FAST
REGULADOR DE ENERGÍA REACTIVAREACTIVE ENERGY REGULATOR
GUÍA DE PROGRAMACIÓNPROGRAMATION GUIDE
Los reguladores Computer SMART III FAST 6 / SMART III FAST 12, miden el cosφ de red y regulan la conexión y desconexión de
condensadores para corregirlo. Además, calculan y visualizan los
principales parámetros eléctricos en redes monofásicas, trifásicas
equilibradas o desequilibradas.
Este manual es una guía de programación y puesta en servicio
del Computer SMART III FAST. Para más información, se puede
descargar el manual completo en la página web de CIRCUTOR:
www.circutor.com
The Computer Smart III FAST 6 / Smart III FAST 12 regulator
measures the power grid cosine and controls capacitor connection
and disconnection in order to correct it. It also calculates and
displays the main electrical parameters of balanced or unbalanced
single-phase and three-phase networks.
This manual is a Computer SMART III FAST programation guide.
For further information, please download the full manual from the
CIRCUTOR web site:
www.circutor.com
Status of thecapacitors
Status of theunit
Data area
Analogue bar
CPU
Fan
Alarm
Key pressed
Relación CT/CT Ratio
(Ip / Is)
Potencia en kvar del primer escalón a 400 V Power of the smallest stage at 400 V (kvar)
2.5 5.0 7.5 10.0 12.5 15.0 20.0 25.0 30.0 40.0 50.0 60.0 75.0 80.0
150/5 0.12 0.24 0.36 0.48 0.60 0.72 0.96
200/5 0.09 0.18 0.27 0.36 0.45 0.54 0.72 0.90
250/5 0.07 0.14 0.22 0.29 0.36 0.43 0.58 0.72 0.87
300/5 0.06 0.12 0.18 0.24 0.30 0.36 0.48 0.60 0.72 0.96
400/5 0.05 0.09 0.14 0.18 0.23 0.24 0.36 0.48 0.58 0.72 0.87
500/5 0.07 0.11 0.14 0.18 0.22 0.29 0.36 0.45 0.54 0.72 0.87
600/5 0.06 0.09 0.12 0.15 0.18 0.24 0.30 0.36 0.48 0.60 0.72 0.90 0.96
800/5 0.07 0.09 0.11 0.14 0.18 0.23 0.27 0.36 0.45 0.54 0.68 0.72
1000/5 0.05 0.07 0.09 0.11 0.14 0.18 0.22 0.29 0.36 0.43 0.54 0.57
1500/5 0.05 0.06 0.07 0.10 0.12 0.14 0.19 0.24 0.29 0.36 0.38
2000/5 0.05 0.07 0.09 0.11 0.14 0.18 0.22 0.27 0.28
2500/5 0.06 0.07 0.09 0.12 0.14 0.17 0.22 0.23
3000/5 0.05 0.06 0.07 0.10 0.12 0.14 0.18 0.19
4000/5 0.05 0.07 0.09 0.11 0.14 0.14
Funciones del teclado / Keyboard functions
Indicadores en pantalla / Display Indicators
Cálculo del Factor C/K / Calculating the C/K Factor
Para tensiones diferentes de 400 V, el resultado de la tabla debe multiplicarse por 400/V, o calcular el parámetro C/K siguiendo las expresiones mostradas.For other voltages or conditions not included in the table, the value of C/K can be obtained by means of a simple calculation.
Tecla / Key Pulsación corta / Short keystroke Pulsación larga / Long keystroke (3s)
Pantalla anterior / Previous screen -
Pantalla siguiente / Next screen. -
Visualización valor mínimo Display of minimum value
Borrado del valor mínimo Erase of minimum value
Visualización valor máximo Display of maximum value
Borrado del valor máximo Erase of maximum value
Parámetro siguiente
Next parameterMenú de programación
Setup menu
Pulsación muy larga (10 s) / Very Long keystroke (10 s):
Entra en las pantalla de Test / Enter Test screens
Tecla / Key Pulsación corta / Short keystroke Pulsación larga / Long keystroke (3s)
Pantalla anterior / Previous screenTest: Conexión manual del con-densador seleccionado / Manual
connects the displayed transformer
Pantalla siguiente / Next screen.Test: Desconexión manual del con-
densador seleccionado / Manual disconnects the displayed transformer
Visualización valor mínimo Display of minimum value -
Visualización valor máximo Display of maximum value -
Parámetro siguiente
Next parameterTest: Anular el proceso de AutoTest
Cancel the AutoTest
Pulsación muy larga (10 s) / Very Long keystroke (10 s):
Entra en las pantalla de Test / Enter Test screens
Tecla / Key Pulsación corta / Short keystroke
Incrementa el valor o muestra la siguiente opción Increases the digit value or shows the next option
Disminuye el valor o muestra la opción anterior Reduces the digit value or shows the previous option
Parámetro de configuración siguiente / Skips to the next digit
Parámetro de configuración anterior / Skips to the previous digit
Entrada/Salida del modo edición / Enter/ Output edit mode
Pantallas de configuración y test, modo consulta Displays configuration and testing, check mode
Pantallas de configuración y test, modo edición Displays configuration and testing, edit mode
Pantallas de medida / Measuring displays
Tabla C/K / Table C/K Factor
Tecla / KeyEl equipo se encuentra en modo de medida y regulación
The unit is in measurement and regulation modeEl equipo no mide ni regula
The unit does not measure or regulate Indica que se está dentro del menú de configuración
Indicates that you are in the setup menu
Indica que se está dentro del menú de test Indicates that you are in the test menu.
Indica que dentro del menú de configuración se está en modo edición Indicates that, within the setup menu, you are in edit mode
Cálculo del C/K
Relación del transformador de corriente (TC)
It= Intensidad de primario de TC.
K=It
5Ic= Intensidad del primer condensador
V.Q
CI3
=
Cálculo C/K
VKQ
KIKC C
⋅⋅==
3/
Ejemplo: Relación del TC= 500/5
1er condensador: 60 kvar; 400V
1. 1005/500 ==K
2. AIC 6,864003
60000=
⋅=
3. C/K = = 0,86786,7100
Calculating the C/K factor
Relation of the current transformer (CT)
It= CT primary current
Ic= The smallest transformer current
V.Q
CI3
=
K=It
5
Calculating the C/K
VKQ
KIKC C
⋅⋅==
3/
Example: Relation of the TC= 500/5
1st transformer: 60 kvar; 400V
1. 1005/500 ==K
2. AIC 6,864003
60000=
⋅=
3. C/K = = 0,86786,7100
CIRCUTOR SAT: 902 449 459 (SPAIN) / (+34) 937 452 919 (out of Spain)Vial Sant Jordi, s/n08232 - Viladecavalls (Barcelona)Tel: (+34) 937 452 900 - Fax: (+34) 937 452 914e-mail : [email protected]
Servicio técnico / Technical service
M02
1H01
-20-
21A
Validar(pulsación corta)
Pantalla de medida
Secuencia Password
Plug&Play
Relación de transformación de corriente
Cos ϕ obje�vo
Tiempo de conexión y de reconexión
Tipo de conexión
Nº escalones
Programa
Factor C/K
Conexión de fase
(pulsación larga 3 s)
(pulsaciones cortas)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
Cualquier pantalla de configuración
Datos simulación
(pulsación larga 3 s)
(pulsación larga 3 s)
Inicio regulación
(o si no tocamos ninguna tecla durante 5 minutos)
Ayuda a configurar automá�camente en el equipo los parámetros básicos para su regulación.Estos parámetros se pueden ajustar manualmente en las siguientes pantallas de configuración.
Configurar el valor de primario y secundario del transformador de corriente
Ver Ajuste de valores
Configurar 1er cos ϕ obje�vo . Consultar el manual completo para activar el
resto de cos ϕ mediante las entradas digitales (opcional).
Configurar los �empos de actuación del equipo en segundos
Seleccionar el �po de conexión de la instalación
Seleccionar la correcta secuencia de fase
Seleccionar el número de escalones, es decir el número de salidas de relé que tendrá el equipo
Determinar la secuencia de escalones con dis�ntas potencias .
Ajustar según la corriente reac�va aportada por el escalón más pequeño, medida en el
secundario del transformador de corriente
“t.on” es el �empo mínimo entre la conexión o la desconexión entre dos escalones.
“t.rec” es el �empo mínimo entre la desconexión y la conexión de un mismo escalón.
Recomendación*: t.on = 10 t.rec = 50(“t.rec” debe ser 5 veces mayor que “t.on”)
Ver sección de cálculo del factor C/K, en esta guía
(o si no tocamos ninguna tecla durante 5 minutos)
Valor entre 0.5 y 1* Recomendación : cos ϕ = 1
3U3C, 3 tensiones (con o sin neutro) y 3 corrientes. - 3U1C, 3 tensiones (con o sin neutro) y 1 corriente.
- 2U1C, 2 tensiones (entre fases) y 1 corriente.
Ejemplo: Programa 1.1.1.1, todos los escalones �enen la misma potencia que el primero.
Programa 1.2.4.4, el 2º escalón �ene potencia doble y los sucesivos cuádruple que el primero
Podemos configurar 6, 12 o 14 salidas según modelo.
Primario valor máximo: 9999. Primario valor mínimo: 1.
Secundario valores posibles: 1 ó 5
Acceso al menú de configuración Acceso a las pantallas de medida
Si se ha seleccionado la conexión con 1 corriente (3U1C ó 2U1C) se puede seleccionar una de las 6 posibles fases que se indican en
el manual completo .Si se ha seleccionado la conexión con 3 corrientes ( 3u3C) se asocia cada corriente con su tensión y se indica el sen�do de la corriente
d : directa. i : inversa.
OFF START
(pulsación corta)
Ajuste de valores y opciones en las pantallas de configuración
:
(Password correcto)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
(pulsación corta)
Validar(pulsación corta)
Validar(pulsación corta)
Validar(pulsación corta)
Validar( pulsación corta)
Validar(pulsación corta)
Validar(pulsación corta)
Validar(pulsación corta)
Validar(pulsación corta)
Pantalla que muestra:- Medida del cos ϕ- Potencia reac�va trifásica- Pasos a conectar
Efectua la conexión de los pasos indicados previamente en la pantalla de simulación.
Pantallas de configuración:
.
Ver Ajuste de valores
Ver Ajuste de valores
Ver Ajuste de valores
Ver Ajuste de valores
Ver Ajuste de valores
Ver Ajuste de valores
Ver Ajuste de valores
Setup AvanzadoAcceder a pantallas de configuración avanzadas, a con�nuación de las pantallas de configuración
básicas. Para el setup avanzado consultar el manual completo
(pulsación corta)
(pulsación corta)Validar(pulsación corta)
Ver Ajuste de valores
* Valores recomendados por CIRCUTOR, revisar particularidades de la instalación, legislacio-nes y reglamentos particulares de cada país.
(”t.on” debe ser ≥ a “t.off”)
Validate( )
Measuring display
Password Secuency
Plug&Play
Current tranforma�on ra�o
Cos ϕ Target
Conec�on and reclosingn �me
Conec�on type
Num. stages
Program
C/K factor
Advanced Setup
Phase conec�on
Long keystroke (3s)
( short keystrokes )
( )
( )
( )
( )
( )
( )
( )
( )
( )
Any configura�ondisplay
Simula�on data
Start regula�on
(
Help to automa�cally configure the basic parameters for regula�on.These parameters can be set manually in the setup displays.
Set the value of primary and secondarycurrent transformer . See Setting of values.
Set 1st cos ϕ target. Check the full manual to activate
rest of cos ϕ via digital inputs(optional).
Set the �me in seconds of device ac�ons.
Select the connec�on type of installa�on.
Select the correct phase sequence.
Select the number of stages, number of relay outputs .
Set the steps sequency with different powers
Access advanced configura�on displays following basic configura�on displays
,
“t.on” is the minimal �me between the conec�on or disconec�on of two steps .
“t..
Recomendation*: t.on = 10 t.rec = 50(“t.rec” must be 5 times greater than “t.on”)
For advanced setup check the manual .
(or if we don’t play any key for 5 mins)
Value between 0.5 * Recomendation: cos ϕ = 1
- 3U3C, 3 voltages ( with or without neutral) and 3 currents. - 3U1C, 3 voltages ( ) and1 current.
- 2U1C, 2 voltages(between phases)
Example: Programe 1.1.1.1, all the stepshave the same power as the first .Programe 1.2.4.4, the 2nd step have doble po-wer and the rest, four �mes more that 1st .
We can set up 6, 12 or 14 outputs according to model
Primary maximum value: 9999. Primary minimum value: 1.
Secundary posibles values : 1 ó 5
Access the setup menu Access Measuring display
- If you select the connec�on with 1 current(3U1C ó 2U1C) youcan select one of the 6 posibles phases shown in the manual.
- If you select the connec�on with 3 currents ( 3u3C ) each current is associated with the voltage and current direc�on indicated.
d : direct. i : invers.
OFF START
( )
Setting of values and options in the configuration displays
:
( correct password )
(short keystroke)
( )
( )
( )
( )
( )
( )
( )
( )
( )
Validate( )
Validate( )
Validate( )
Validate( )
Validate( )
Validate( )
Validate( )
Validate( )
Validate( )
Display showing:- Measurement of cos ϕ- Reac�ve power phase- Steps to connect
Makes the connec�on of the previously men�oned steps in the simula�on display
Configura�ondisplay:
.
short keystroke
short keystroke
short keystroke
short keystrokeshort keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
short keystroke
Long keystroke (3s)
Long keystroke (3s) or if we don’t play any key for 5 mins)
See sec�on for calcula�ng C/K Factor
rec” is the minimal �me between the conec�on or disconec�on of same step
with or without neutraland1 curent.
See Setting of values
See Setting of values
See Setting of values
See Setting of values
See Setting of values
See Setting of values
See Setting of values
The C/K factor is adjusted according to the reac�ve current provided by the smallest stage,
measured in the secondary of the current transformer. See Setting of values
(”t.on” must be ≥ that “t.off”)
and 1
* Recommended values by CIRCUTOR, check the particularity of the own instalation, legislations and regulations in each country
Increases the digit value or shows the next option
Reduces the digit value or shows the next option
Skips to the next digit
Skips to the previous digit
Enter/ Output edit mode
Key Short keystroke