CONCRETE/CMU APPLICATION DETAIL Page 2...detail #: awb –30 . the above detail isfor illustrationpurposesonly.it intended asa guideline to assist momentive product users developing

GE ELEMAX™ 2600 AIR and WATER-RESISTIVE BARRIER SYSTEM

CONCRETE/CMU APPLICATION DETAIL......................................................................................... Page 2CONCRETE/CMU PARAPET TIE IN – METHOD A............................................................................ Page 3CONCRETE/CMU PARAPET TIE IN – METHOD B............................................................................ Page 4STATIC JOINTS>1/2", EXPANSION & DRIFT JOINTS....................................................................... Page 5PENETRATIONS – METHOD A: GE ELEMAX 5000 LIQUID FLASHING............................................. Page 6PENETRATIONS – METHOD B: GE RF100 REINFORCING FABRIC................................................... Page 7INSIDE/OUTSIDE CORNERS – GE ELEMAX 5000 LIQUID FLASHING............................................... Page 8INSIDE/OUTSIDE CORNERS – GE RF100 REINFORCING FABRIC.................................................... Page 9TERMINATION AT GRADE – FLUSH WITH FOUNDATION.............................................................. Page 10TERMINATION AT GRADE – CMU/CONCRETE OVERLAPPING FOUNDATION............................... Page 11TERMINATION AT FOUNDATION – THROUGH WALL FLASHING AT BASE.................................... Page 12BRICK/SHELF ANGLE...................................................................................................................... Page 13ROUGH OPENING – METHOD A: GE ELEMAX LIQUID FLASHING.................................................. Page 14ROUGH OPENING – METHOD B: GE RF100 REINFORCING FABRIC............................................... Page 15ROUGH OPENING – METHOD C: GE ELEMAX SS FLASHING.......................................................... Page 16

SCALE: N.T.S.

DATE: 2017 - 03 - 27

DETAIL #: AWB – 26

THE ABOVE DETAIL IS FOR ILLUSTRATION PURPOSES ONLY. IT IS INTENDED AS A GUIDELINE TO ASSIST MOMENTIVE PRODUCT USERS IN DEVELOPING PROJECT SPECIFIC DETAILS. CONSULT APPROPRIATE SPECIFICATION DOCUMENTS, DATA SHEET, BUILDING CODES AND ANY OTHER INFORMATION DEEMED NECESSARY FOR SPECIFIC REQUIREMENTS. MOMENTIVE PRODUCT USERS ARE RESPONSIBLE FOR DETERMINING THE SUITABILITY OF MOMENTIVE PRODUCTS FOR THE PARTICULAR APPLICATION AND ALL RELATED PROJECT DETAILS. MOMENTIVE MAKES NO WARRANTY, EXPRESS OR IMPLIED, WITH RESPECT TO THE PERFORMANCE SUITABILITY OR FITNESS FOR INTENDED USE OF ITS PRODUCTS IN ANY USER’S APPLICATION. ANY SALE OF PRODUCTS OR DELIVERY OF CUSTOMER SUPPORT AND ADVICE BY MOMENTIVE PERFORMANCE MATERIALS INC. AND/OR ANY OF ITS AFFILIATES. (“MOMENTIVE”) IS MADE EXCLUSIVELY UNDER MOMENTIVES STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE AT WWW.GESILICONES.COM. *GE IS A TRADEMARK OF GENERAL ELECTRIC COMPANY. USED UNDER TRADEMARK LICENSE. MOMENTIVE IS THE EXCLUSIVE PARTNER LICENSED BY GENERAL ELECTRIC COMPANY TO DEVELOP AND MANUFACTURE GE SILICONES COATINGS AND SEALANTS. COPYRIGHT 2021 MOMENTIVE PERFORMANCE MATERIALS INC. ALL RIGHTS RESERVED.

CMU APPLICATION DETAILGE ELEMAX 2600 AIR AND WATER-RESITIVE BARRIER SYSTEM

Page 2

CMU CONSTRUCTION

CRACK, CONTROL JOINT OR COLD JOINT

GE ELEMAX 5000 LIQUID FLASHING 20-40 MILS (508-1016 µ) THICK

GE ELEMAX 2600 AWB

• ENSURE SURFACE IS DRY, CLEAN AND FREE OF DIRT, DEBRIS AND CONTAMINANTS.• CLEAN LOOSE MORTAR AND OTHER CONTAMINATIONS WHERE NECESSARY BY WIRE BRUSH OR SIMILAR ABRASION TO PROVIDE A STABLE CLEAN SURFACE FOR APPLICATION.• MASONRY JOINTS SHALL BE STRUCK FLUSH.• CRACKS OR VOIDS AT JOINTS GREATER THAN 1/16" [2 MM) AND UP TO 1/2" [13 MM) SHALL BE FILLED [ROUTED AND FILLED WHERE NECESSARY) WITH A TROWEL APPLICATION OF GE ELEMAX 5000 LIQUID

FLASHING PRIOR TO APPLICATION OF GE ELEMAX 2600 AWB. REPAIR LARGER CRACKS OR VOIDS WITH NON-SHRINKING GROUT OR OTHER APPROPRIATE PATCHING MATERIAL.• WHEN SPRAY APPLYING OVER CMU, BACK ROLLING WILL BE REQUIRED TO ENSURE A PIN HOLE FREE APPLICATION.

• SEE GE ELEMAX 2600 AWB DATA SHEET FOR LIST OF ADDITIONAL ACCEPTABLE GE SEALANTS/LIQUID FLASHING.

NOTES:

marnimcniff

Rectangle

SCALE: N.T.S.

DATE: 2020 – 11 – 16



CONCRETE/CMU PARAPET TIE-IN – METHOD AGE ELEMAX 2600 AIR AND WATER-RESITIVE BARRIER SYSTEM

GE ENDURIS™ / ROOF MEMBRANE, BY OTHERS

NOTES:• ENSURE PARAPET IS DRY, CLEAN AND FREE OF DIRT, DEBRIS, AND

CONTAMINENTS.• GE ELEMAX 5000 LIQUID FLASHING MAY BE INSTALLED BEFORE OR AFTER

THE APPLICATION OF GE ELEMA 2600 AWB.• ENSURE GE ELEMAX 2600 AWB IS DRY TO THE TOUCH PRIOR TO THE

APPLICATION OF GE ELEMAX 5000 LIQUID FLASHING.• SPREAD/TROWEL GE ELEMAX 5000 LIQUID FLASHING TO A MINIMUM OF 3”

OVERLAP ONTO THE TOP AND BOTH SIDES OF THE PARAPET. LIQUID FLASHING SHOULD BE CONTINUOUS AND SMOOTH WHILE FREE OF POCKETS, VOIDS, AND/OR PINHOLES.

• GE RF100 REINFORCING FABRIC EMBEDDED IN GE ELEMAX 2600 AWB OR GE ULTRASPAN™ UST2200 SILICONE TRANSITION SHEET EMBEDDED IN GE ELEMAX 5000 LIQUID FLASHING MAY ALSO BE UTILIZED TO TREAT PARAPET.


• CONFRIM ADHESION AND COMPATIBILTY TO ROOF MEMBRANE BY OTHERS.

GE ELEMAX 2600 AWB

GE ELEMAX 5000 LIQUID FLASHING (20-40 MILS THICK)

Page 3

SCALE: N.T.S.

DATE: 2020 – 11 – 16



CONCRETE/CMU PARAPET TIE-IN – METHOD BGE ELEMAX 2600 AIR AND WATER-RESITIVE BARRIER SYSTEM

GE ENDURIS / ROOF MEMBRANE, BY OTHERS

NOTES:• ENSURE PARAPET IS DRY, CLEAN AND FREE OF DIRT, DEBRIS, AND

CONTAMINENTS.• GE ELEMAX SS FLASHING SHOULD BE INSTALLED BEFORE THE APPLICATION

OF GE ELEMAX 2600 AWB.• IF THE ELEMAX 2600 AWB HAS ALREADY BEEN APPLIED, EMBED ELEMAX SS

FLASHING IN ELEMAX 5000 LIQUID FLASHING.• ENSURE GE ELEMAX SS FLASHING IS APPLIED A MINIMUM OF 3” OVERLAP

ONTO THE TOP AND BOTH SIDES OF THE PARAPET. SS FLASHING SHOULD BE CONTINUOUS AND SMOOTH WHILE FREE OF WRINKLES, VOIDS, AND/OR FISHMOUTHS.

• GE RF100 REINFORCING FABRIC EMBEDDED IN GE ELEMAX 2600 AWB OR GE ULTRASPAN UST2200 SILICONE TRANSITION SHEET EMBEDDED IN GE ELEMAX 5000 LIQUID FLASHING MAY ALSO BE UTILIZED TO TREAT PARAPET.


• CONFRIM ADHESION AND COMPATIBILTY TO ROOF MEMBRANE BY OTHERS.

GE ELEMAX 2600 AWB

GE ELEMAX SS FLASHING

Page 4

SCALE: N.T.S.

DATE: 2020 – 11 – 16



STATIC JOINTS>1/2”, EXPANSION & DRIFT JOINTS GE ELEMAX 2600 AIR AND WATER-RESITIVE BARRIER SYSTEM

ADHERE GE ULTRASPAN UST2200 SILICONE TRANSITION SHEET OVER CENTER OF JOINT UTILIZING GE ELEMAX 5000 LIQUID FLASHING OR GE ELEMAX 2600 AWB AS AN ADHESIVE

GE ELEMAX 2600 AWB

NOTES:• GE ULTRASPAN UST2200 SILICONE TRANSITION SHEET MAY BE APPLIED

EITHER BEFORE OR AFTER APPLICAION OF GE ELEMAX 2600 AWB.• WHEN UTILIZING GE ELEMAX 5000 LIQUID FLASHING AS AN ADHESIVE,

SPREAD/TROWEL SMOOTH TO 20-40 MILS THICK. ADHERE GE ULTRASPAN UST2200 SILICONE TRANSITION SHEET AND ENSURE EDGES ARE FULLY EMBEDDED IN GE ELEMAX 5000 LIQUID FLASHING.

• WHEN UTILIZING GE ELEMAX 2600 AWB AS AN ADHESIVE, APPLY FIRST COAT (MIN. 10 MILS) BY ROLLER IN SUFFICIENT WIDTH TO ACCOMMODATE GE ULTRASPAN UST2200 SILICONE TRANSITION SHEET. WAIT UNTIL COATING BECOMES TACKY AND PRESS GE ULTRASPAN UST2200 SILICONE TRANSITION SHEET INTO THE COATING. APPLY A SECOND COAT OF GE ELEMAX 2600 AWB (MIN. 10 MILS) IMMEDIATELY OVER THE GE ULTRASPAN UST2200 SILICONE TRANSITION SHEET.

• SEE GE ELEMAX 2600 DATA SHEET FOR LIST OF ADDITIONAL ACCEPTABLE GE SEALANTS/LIQUID FLASHING.

Page 5

SCALE: N.T.S.

DATE: 2020 – 11 – 16



PENETRATIONS – METHOD A: GE ELEMAX 5000 LIQUID FLASHING GE ELEMAX 2600 AIR AND WATER-RESITIVE BARRIER SYSTEM

OPTION 1 (COATING FIRST) OPTION 2 (SEALANT FIRST)

GE ELEMAX 5000 LIQUID FLASHING

GE ELEMAX 2600 AWB

GE ELEMAX 2600 AWB


NOTES:• ENSURE AREAS AT PENETRATION ARE DRY, CLEAN, AND FREE OF ANY DIRT, DEBRIS, OR CONTAMINENTS.• PENETRATIONS MAY BE TREATED BEFORE OR AFTER THE APPLICATION OF GE ELEMAX 2600 AWB.• OPTION 1: APPLY A CONTINUOUS APPLICATION OF GE ELEMAX 2600 AWB OVER ENTIRE FACE OF CMU/

CONCRETE AND AROUND PERIMETER OF PENETRATION. ALLOW GE ELEMAX 2600 AWB TO CURE SUFFICIENTLY PRIOR TO SEALING THE PENETRATION WITH GE ELEMAX 5000 LIQUID FLASHING. USE BACKER ROD OR POLYURETHANE SPRAY FOAM WHERE NECESSARY. TRIM SPRAY FOAM FLUSH PRIOR TO DETAILING.

• OPTION 2: SEAL PERIMETER WITH GE ELEMAX 5000 LIQUID FLASHING. USE BACKER ROD ORPOLYURETHANE SPRAY FOAM WHERE NECESSARY. TRIM SPRAY FOAM FLUSH PRIOR TO DETAILING. APPLY A CONTINUOUS APPLICATION OF GE ELEMAX 2600 AWB OVER ENTIRE FACE OF CMU/CONCRETE, OVERLAPPING THE SEALANT BEAD AT THE PENETRATION PERIMETER.

• SEE GE ELEMAX 2600 AWB DATA SHEET FOR LIST OF ADDITIONAL ACCEPTABLE GE SEALANTS/LIQUIDFLASHING.

Page 6

SCALE: N.T.S.

DATE: 2020 – 11 – 16



PENETRATIONS – METHOD B: GE RF100 REINFORCING FABRIC GE ELEMAX 2600 AIR AND WATER-RESITIVE BARRIER SYSTEM

GE ELEMAX 2600 AWB

GE RF100 REINFORCING FABRIC

NOTES:• CUT A SQUARE PIECE OF GE RF100 REINFORCING FABRIC LARGE ENOUGH

TO EXTEND PAST THE PENETRATION BY 2” IN ALL DIRECTIONS.• AT THE CENTER OF THE SQUARE PIECE OF GE RF100 REINFORCING FABRIC,

CUT A SMALL HOLE WITH A RAZOR BLADE OR SCISSORS.• CUT AN “X” USING THE SMALL HOLE PREVIOUSLY CUT AS YOUR STARTING

POINT. ROTATE THE SQUARE ABOUT 45° AND CUT ANOTHER “X”.• APPLY CUT GE RF100 REINFORCING FABRIC OVER THE PENETRATION

PROPERLY EMBEDDED IN GE ELEMAX 2600 AWB WITH A MINIMUM OF 2” ON EACH SIDE WITH THE CUT TABS POINTED OUTWARD. PRESS GE RF100 REINFORCING FABRIC FLUSH WITH CMU/CONCRETE, SEE STEP 1.

• EMBED THE GE RF100 REINFORCING FABRIC IN GE ELEMAX 2600 AWBAND COAT THE TABS AROUND THE PIPE, SEE STEP 2.

• WRAP A 1” STRIP OF GE RF100 REINFORCING FABRIC EMBEDDED IN GE ELEMAX 2600 AWB AROUND THE TABS.


Page 7

SCALE: N.T.S.

DATE: 2020 – 11 – 16



INSIDE/OUTSIDE CORNERS – METHOD A: GE ELEMAX 5000 LIQUID FLASHING GE ELEMAX 2600 AIR AND WATER-RESITIVE BARRIER SYSTEM

NOTES:• GE ELEMAX 5000 LIQUID FLASHING MAY BE INSTALLED BEFORE OR AFTER

THE APPLICATION OF GE ELEMAX 2600 AWB. • ENSURE GE ELEMAX 2600 AWB IS DRY TO THE TOUCH PRIOR TO THE

APPLICATION OF GE ELEMAX 5000 LIQUID FLASHING. • INSIDE CORNER: A PROPERLY CONFIGURED FILLET BEAD OF GE ELEMAX

5000 LIQUID FLASHING MAY BE UTILIZED TO TREAT CHANGE IN SUBSTRATE AT INSIDE CORNERS WITH GAPS < 1/2”. THE USE OF BACKER ROD MAY BE REQUIRED. ENSURE A MINIMUM 1/4” – 3/8” ADHESIVE CONTACT TO BOTH SIDES.

• OUTSIDE CORNER: APPLY GE ELEMAX 5000 LIQUID FLASHING TO THE OUTSIDE CORNER AT A NOMINAL 20-40 MILS THICKNESS. SPREAD/TROWEL GE ELEMAX 5000 LIQUID FLASHING TO A MINIMUM OF 3” ONTO EACH SIDE OF WALL.




GE ELEMA 2600 AWB

Page 8

SCALE: N.T.S.

DATE: 2020 – 11 – 16



INSIDE/OUTSIDE CORNERS – METHOD B: GE RF100 REINFORCING FABRIC GE ELEMAX 2600 AIR AND WATER-RESITIVE BARRIER SYSTEM

NOTES:• INSIDE/OUTSIDE CORNERS MAY BE INSTALLED BEFORE OR AFTER THE

APPLICATION OF GE ELEMAX 2600 AWB. • APPLY A LIBERAL COAT (MIN. 10 MILS) OF GE ELEMAX 2600 AWB IN

SUFFICIENT WIDTH TO ACCOMMODATE GE RF100 REINFORCING FABRIC. WHILE STILL WET, SET 6” GE RF100 REINFORCING FABRIC INTO THE GE ELEMAX 2600 AWB AND CENTER ON INSIDE/OUTSIDE CORNER. APPLY ASECOND COAT (MIN. 10 MILS) OF GE ELEMAX 2600 AWB IMMEDIATELY OVER THE GE RF100 REINFORCING FABRIC, ENSURING A PINHOLE FREE APPLICATION IS ACHIEVED.

• GE ULTRASPAN UST2200 SILICONE TRANSITION SHEET EMBEDDED IN GE ELEMAX 5000 LIQUID FLASHING MAY ALSO BE UTILIZED TO TREAT INSIDE/OUTSIDE CORNERS.




GE ELEMAX 2600 AWB

Page 9

SCALE: N.T.S.

DATE: 2020 – 11 – 16



TERMINATION AT GRADE – FLUSH WITH FOUNDATIONGE ELEMAX 2600 AIR AND WATER-RESITIVE BARRIER SYSTEM

NOTES:• IT IS RECOMMENDED TO CHECK THE ADHESION AND COMPATIBILITY OF

GE PRODUCTS TO FLASHINGS AND BELOW GRADE WATERPROOFING.• ENSURE BELOW GRADE WATERPROOFING IS INSTALLED PRIOR TO THE

APPLICATION OF GE PRODUCTS. CONTACT MOMENTIVE TECHNICAL SERVICES FOR TRANSITIONING TO FLUID APPLIED ASPHALTIC OR BITUMINOUS BASED BELOW GRADE WATERPROOFING.

• ENSURE GE ELEMAX 5000 LIQUID FLASHING IS INSTALLED A MINIMUM 2” ONTO ABOVE GRADE WALL AND A MINIMUM OF 2” ONTO BELOW GRADE WATERPROOFING.

• GE RF100 REINFORCING FABRIC EMBEDDED IN GE ELEMAX 2600 AWB, GE ELEMAX SS FLASHING OR GE ULTRASPAN UST2200 SILICONE TRANSITION SHEET EMBEDDED IN GE ELEMAX 5000 LIQUID FLASHING MAY ALSO BE UTILIZED TO TREAT FLASHING AND FOUNDATION TERMINATION.


GE ELEMAX 2600 AWB


BELOW GRADE WATERPROOFING, BY OTHERS

Page 10

SCALE: N.T.S.

DATE: 2020 – 11 – 16



TERMINATION AT GRADE – CMU/CONCRETE OVERLAPPING FOUNDATION GE ELEMAX 2600 AIR AND WATER-RESITIVE BARRIER SYSTEM

GE ELEMAX 2600 AWB


BELOW GRADE WATERPROOFING, BY OTHERS

NOTES:• IT IS RECOMMENDED TO CHECK THE ADHESION AND COMPATIBILITY OF

GE PRODUCTS TO FLASHINGS AND BELOW GRADE WATERPROOFING.• ENSURE BELOW GRADE WATERPROOFING IS INSTALLED PRIOR TO THE

APPLICATION OF GE PRODUCTS. CONTACT MOMENTIVE TECHNICAL SERVICES FOR TRANSITIONING TO FLUID APPLIED ASPHALTIC OR BITUMINOUS BASED BELOW GRADE WATERPROOFING.

• ENSURE GE ELEMAX 5000 LIQUID FLASHING IS INSTALLED A MINIMUM 2” ONTO ABOVE GRADE WALL AND A MINIMUM OF 2” ONTO BELOW GRADE WATERPROOFING.

• GE RF100 REINFORCING FABRIC EMBEDDED IN GE ELEMAX 2600 AWB, GE ELEMAX SS FLASHING OR GE ULTRASPAN UST2200 SILICONE TRANSITION SHEET EMBEDDED IN GE ELEMAX 5000 LIQUID FLASHING MAY ALSO BE UTILIZED TO TREAT FLASHING AND FOUNDATION TERMINATION.


Page 11

SCALE: N.T.S.

DATE: 2020 – 11 – 16



TERMINATION AT FOUNDATION – THROUGH WALL FLASHING AT BASE GE ELEMAX 2600 AIR AND WATER-RESITIVE BARRIER SYSTEM

GE ELEMAX 2600 AWB

FOUNDATION


SEAL TOP OF TERMINATION BAR WITH A CONTINUOUS 1/4” X 1/4” BEAD OF GE ELEMAX™ 5000 LIQUID FLASHING

NOTES:• IN LIEU OF UTILIZING A TERMINATION BAR, THE TOP EDGE OF GE ELEMAX SS

FLASHING CAN BE SET IN A LAYER OF UNCURED GE ELEMAX 5000 LIQUID FLASHING TROWELED SMOOTH AT A MINIMUM OF 30 MILS THICK BY 1” WIDE.

• IF FULL SURFACE ADHESION OF THROUGH WALL FLASHING (TWF) TO SUBSTRATE IS DESIRED, INSTALL GE ELEMAX SS FLASHING PRIOR TO THE APPLICAITION OF GE ELEMAX 2600 AWB AND GE ELEMAX 5000 LIQUID FLASHING. ENSURE TOP EDGE OF FLASHING IS SEALED WIT GE ELEMAX 5000 LIQUID FLASHING.

• A PROPERLY CONFIGURED FILLET BEAD OF GE ELEMAX 5000 LIQUID FLASHING SHOULD BE INSTALLED AT BASE OF WALL A MINIMUM 1/4” – 3/8” ADHESIVE CONTACT TO BOTH SIDES.

• CONTACT MOMENTIVE TECHNICAL SERVICES FOR ALTERNATE TWF TRANSITIONING OPTIONS.

• IT IS RECOMMENDED TO CHECK ADHESION AND COMPATIBILITY OF GE PRODUCTS TO TWF AND ASSOCIATED COMPONENTS PRIOR TO USE. GE SS80PRIMER CAN BE USED IF NEEDED.


MASONRY VENEER


Page 12

SCALE: N.T.S.

DATE: 2020 – 11 – 16



BRICK/SHELF ANGLE GE ELEMAX 2600 AIR AND WATER-RESITIVE BARRIER SYSTEM

MASONRY VENEER

WEEP VENT INSERTS

GE ELEMAX 2600 AWB

SEAL TOP EDGE OF ANGLE WITH GE ELEMAX 5000 LIQUID FLASHING

DRIP EDGE

NOTES:• IN LIEU OF UTILIZING A TERMINATION BAR, THE TOP EDGE OF GE ELEMAX SS

FLASHING CAN BE SET IS A LAYER OF UNCURED GE ELEMAX 5000 LIQUID FLASHING TROWELED SMOOTH AT A MINIMUM OF 30 MILS THICK BY 1” WIDE.

•

•

IF FULL SURFACE ADHESION OF THROUGH WALL FLASHING (TWF) TO SUBSTRATE IS DESIRED, INSTALL GE ELEMAX SS FLASHING PRIOR TO THE APPLICAITION OF GE ELEMAX 2600 AWB AND GE ELEMAX 5000 LIQUID FLASHING. ENSURE TOP EDGE OF FLASHING IS SEALED WIT GE ELEMAX 5000LIQUID FLASHING. CONTACT MOMENTIVE TECHNICAL SERVICES FOR ALTERNATE TWF TRANSITIONING OPTIONS.

• IT IS RECOMMENDED TO CHECK ADHESION AND COMPATIBILITY OF GE PRODUCTS TO TWF AND ASSOCIATED COMPONENTS PRIOR TO USE. GE SS80PRIMER CAN BE USED IF NEEDED.



Page 13

SCALE: N.T.S.

DATE: 2020 – 11 – 16

DETAIL #: AWB - 38


ROUGH OPENING – METHOD A: ELEMAX 5000 LIQUID FLASHING GE ELEMAX 2600 AIR AND WATER-RESITIVE BARRIER SYSTEM

GE ELEMAX 2600 AWBGE ELEMAX 5000 LIQUID FLASHING (20-40 MILS THICK)

APPLY GE ELEMAX 5000 LIQUID FLASHING TO THE ROUGH OPENING AT A NOMINAL 20-40 MILS THICKNESS. SPREAD/TROWEL THE GE ELEMAX 5000 LIQUID FLASHING TO A MINIMUM OF 3” ONTO WALL AND 3” INTO ROUGH OPENING. LIQUID FLASHING SHOULD BE CONTINUOUS AND SMOOTH WHILE FREE OF POCKETS, VOIDS AND/OR PINHOLES.

APPLY/TOOL GE ELEMAX 5000 LIQUID FLASHING TO INSIDE CORNERS OF ROUGH OPENING TO ENSURE SEAMLESS COVERAGE.

NOTES:• ENSURE ROUGH OPENINGS ARE DRY, CLEAN AND FREE OF DIRT, DEBRIS AND

CONTAMINANTS. • GE ELEMAX 5000 LIQUID FLASHING MAY BE INSTALLED BEFORE OR AFTER THE

APPLICATION OF GE ELEMAX 2600 AWB. • ENSURE GE ELEMAX 2600 AWB IS DRY TO THE TOUCH PRIOR TO THE

APPLICATION OF GE ELEMAX 5000 LIQUID FLASHING. • THE USE OF USM ULTRASPAN PRE-CURED SILICONE MOLDED CORNERS MAY

ALSO BE UTILIZED. ENSURE GE ELEMAX 5000 LIQUID FLASHING EXTENDS A MIN. 2” OVER USM ULTRASPAN PRE-CURED SILICONE MOLDED CORNERS PROPERLY EMBEDDED IN GE ELEMAX 5000 LIQUID FLASHING.


Page 14

SCALE: N.T.S.

DATE: 2020 – 11 – 17



ROUGH OPENING – METHOD B: GE RF100 REINFORCING FABRIC GE ELEMAX 2600 AIR AND WATER-RESITIVE BARRIER SYSTEM

GE ELEMAX 2600 AWB




CONTAMINENTS. • ROUGH OPENING MAY BE TREATED BEFORE OR AFTER THE APPLICATION

OF GE ELEMAX 2600 AWB OVER WALL AREAS. AN ADDITIONAL COAT OF GE ELEMAX 2600 AWB OVER AREAS TREATED WITH GE RF100 REINFORCING FABRIC MAY BE REQUIRED TO ENSURE A PINHOLE FREE APPLICATION IS ACHIEVED.

• APPLY GE ELEMAX 5000 LIQUID FLASHING TO INSIDE CORNERS TO ENSURE SEAMLESS COVERAGE.

• GE RF100 REINFORCING FABRIC SHOULD BE INSTALLED IN MANAGEABLE SEGMENTS. ENSURE GE RF100 REINFORCING FABRIC SEGMENTS OVERLAP BY AMINIMUM OF 2”.

• THE USE OF USM ULTRASPAN PRE-CURED SILICONE MOLDED CORNERS MAY ALSO BE UTILIZED. ENSURE GE ELEMAX 5000 LIQUID FLASHING EXTENDS A MIN. 2” OVER USM ULTRASPAN PRE-CURED SILICONE MOLDED CORNERS PROPERLY EMBEDDED IN GE ELEMAX 5000 LIQUID FLASHING.



CUT MINIMUM 6” GE RF100 REINFORCING FABRIC TO APPROPRIATE LENGTH AND SHAPE. APPLY A LIBERAL FIRST COAT (MIN. 10 MILS) OF GE ELEMAX 2600 AWB SUFFICIENT TO SATURATE GE RF100 REINFORCING FABRIC AND EXTEND AT LEAST 1” BEYOND GE RF100 REINFORCING FABRIC WIDTH. WHILE STILL WET, PLACE GE RF100 REINFORCING FABRIC IN GE ELEMAX 2600 AWB AND EMBED BY APPLYING A SECOND COAT (MIN. 10 MILS) BY ROLLER OF GE ELEMAX 2600 AWB, ENSURING A PINHOLE FREE APPLICATION IS ACHIEVED. GE RF100 REINFORCING FABRIC MUST EXTEND A MINIMUM OF 3” ONTO THE WALL AND MINIMUM 3” INTO THE ROUGH OPENING (OR PAST PRIMARY SEAL OF WINDOW) IN THE FOLLOWING ORDER: APPLY GE RF100 REINFORCING FIRST TO THE SILL, THEN THE JAMBS, FINISHING WITH THE HEAD OF THE ROUGH OPENING TO ENSURE PROPER LAP SEQUENCE.

Page 15

SCALE: N.T.S.

DATE: 2020 – 11 – 17



ROUGH OPENING – METHOD C: GE ELEMAX SS FLASHINGGE ELEMAX 2600 AIR AND WATER-RESITIVE BARRIER SYSTEM

GE ELEMAX 2600 AWB



CUT MINIMUM 6” GE ELEMAX SS FLASHING TO APPROPRIATE LENGTH AND SHAPE. GE ELEMAX SS FLASHING MUST EXTEND A MINIMUM OF 3” ONTO THE WALL AND MINIMUM 3” INTO THE ROUGH OPENING (OR PAST PRIMARY SEAL OF WINDOW) IN THE FOLLOWING ORDER: INSTALL GE ELEMAX SS FLASHING FIRST TO THE SILL, THEN THE JAMBS, FINISHING WITH THE HEAD OF THE ROUGH OPENING TO ENSURE PROPER LAP SEQUENCE.


ENSURE GE ELEMAX 2600 AWB EXTENDS A MINIMUM OF 2” ONTO GE ELEMAX SS FLASHING. GE ELEMAX 5000 LIQUID FLASHING MAY ALSO BE UTILIZED TO SEAL EDGE OF GE ELEMAX SS FLASHING.


CONTAMINENTS. • GE ELEMAX SS FLASHING SHOULD BE INSTALLED BEFORE THE APPLICATION OF

GE ELEMAX 2600 AWB OVER WALL SUBSTRATE AND GE ELEMAX 5000 LIQUID FLASHING DETAIL SEALANT.

• APPLY GE ELEMAX 5000 LIQUID FLASHING TO INSIDE CORNERS TO ENSURE SEAMLESS COVERAGE.

• GE ELEMAX SS FLASHING SHOULD BE INSTALLED IN MANAGEABLE SEGMENTS. ENSURE GE ELEMAX SS FLASHING SEGMENTS OVERLAP BY AMINIMUM OF 2”.

• THE USE OF USM ULTRASPAN PRE-CURED SILICONE MOLDED CORNERS MAY ALSO BE UTILIZED. ENSURE GE ELEMAX 5000 LIQUID FLASHING EXTENDS A MIN. 2” OVER USM ULTRASPAN PRE-CURED SILICONE MOLDED CORNERS PROPERLY EMBEDDED IN GE ELEMAX 5000 LIQUID FLASHING.


Page 16

Documents

CONCRETE/CMU APPLICATION DETAIL Page 2...detail #: awb –30 . the above detail isfor illustrationpurposesonly.it intended asa guideline to assist momentive product users developing