Contractor Directorvnit.ac.in/stores/wp-content/uploads/2020/02/schedule-B.pdf · Excavation for foundation in earth, soil of all types, sand, graveland soft murum, including removing

Sr. No. Description Amount

A Amount of Civil Work

B Amount of Furniture Work

C Amount of Electrification Work

Total Cost A+B+CPlus GST as applicable

Contractor Director

SUMMARY

Name of Work :- CONSTRUCTION OF RESIDENTIAL QUARTER'S FOR FACULTY AT VNIT, NAGPUR.(2nd call)

A) CIVIL WORK

(in figure) (in words)

1

Excavation for foundation in earth, soil of all types,sand, gravel and soft murum, including removing theexcavated material up to a distance of 50 m. beyondthe building area and stacking and spreading asdirected, dewatering, preparing the bed for thefoundation and necessary back filling, ramming,watering including shoring and strutting etc.complete. (Lift upto 1.5 m.) Bd.A.1 Page No. 259

1200 Cu.m.

2

Excavation for foundation in earth, soil of all types,sand, gravel and soft murum, including removing theexcavated material up to a distance of 50 m. beyondthe building area and stacking and spreading asdirected, dewatering, preparing the bed for thefoundation and necessary back filling, ramming,watering including shoring and strutting etc.complete. (Lift from1.5 m.to 3.0 m) Bd.A.1 PageNo. 259

550 Cu.m.

3

Filling in plinth and floors with approved excavatedmaterial in 15cm. to 20cm. layers including wateringand compacting etc. complete. Bd.A.10 Page No.262

250 Cu.m.

Estimated Quantity Unit Rate in Rs. Amount

VISVESVARAYA NATIONAL INSTITUTE OF TECHNOLOGY, NAGPUR.

S C H E D U L E -B

Name of work :- CONSTRUCTION OF RESIDENTIAL QUARTER'S FOR FACULTY AT VNIT, NAGPUR.

Item no. Items of work

(2nd call)

(in figure) (in words) Estimated

Quantity Unit Rate in Rs. AmountItem no. Items of work

4

Providing and Filling in plinth and foundation withmurrum/stonedust i. e. contractors material/broughtfrom outside and approved by Engineer incharge inlayers of 15 cm to 20 cm including watering andcompaction etc. complete.

225 Cu.m.

Bd-E : PLAIN CEMENT CONCRETE

5

Providing and laying Cast in situ/Ready Mix cementconcrete in M15 of trap/ granite/quartzite/gneissmetal for bed blocks, foundation blocks and suchother items including bailing out water, plywood/steelformwork, laying/ pumping, compacting, rougheningthem if special finish is to be provided, finishinguneven and honeycombed surface and curing etc.complete. The Cement Mortar 1:3 plaster isconsidered for rendering uneven and honeycombedsurface only. Newly laid concrete shall be covered bygunny bag, plastic, tarpaulin etc. (Wooden centeringwill not be allowed.), with fully automatic microprocessor based PLC with SCADA enabledreversible Drum Type mixer/ concrete Batch mixplant (Pan mixer) etc. complete. With naturalsand/V.S.I. quality Artificial Sand Bd.E.4 Page No.289 and B-7, Page No.38

75 Cu.m.

6

Providing and placing in position Polythene of 50microns below plinth slab of approved quality andmake or as directed by Engineer-in-charge. 600 Sq.M

Bd - F : REINFORCED CEMENT CONCRETE



7

Providing and laying in situ/Ready Mix cementconcrete M-25 of trap / granite /quartzite/ gneissmetal for R.C.C. work in foundations like raft, stripfoundations, grillage and footings of R.C.C. columnsand steel stanchions etc. including bailing out water,formwork, laying/pumping cover blocks, compactionand curing roughening the surface if special finish isto be provided (Excluding reinforcement andstructural steel) etc. complete, with fully automaticmicro processor based PLC with SCADA enabledreversible Drum Type mixer/ concrete Batch mixplant (Pan mixer) etc. complete. With fineaggrgate,natural sand/crushed sand V.S.I. gradefinely washed etc. Bd.F.3 Page No. 298and B.7, Page No.38

140 Cu.m.



8

Providing and laying Cast in situ/Ready Mix cementconcrete M-25 of trap / granite /quartzite/ gneissmetal for R.C.C. columns as per detailed designsand drawing or as directed including centering,formwork, cover blocks, laying/pumping, compactionfinishing the formed surfaces with cement mortar 1:3of sufficient minimum thickness to give a smooth andeven surface or roughening if special finish is to beprovided and curing etc. complete,(Excludingreinforcement and structural steel).with fullyautomatic micro processor based PLC with SCADAenabled reversible Drum Type mixer/ concrete Batchmix plant (Pan mixer) etc. complete. With fineaggrgate,natural sand/crushed sand V.S.I. gradefinely washed etc. Bd.F.5 Page No. 300and B.7, Page.No. 38

125 Cu.m.



9

Providing and laying Cast in situ/Ready Mix cementconcrete M-25 of trap / granite /quartzite/ gneissmetal for R.C.C. beams and lintels ( includingsloping beams ) as per detailed designs anddrawings or as directed including centering,formwork, cover blocks, laying/pumping,compactionand roughening the surface if specialfinish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel). withfully automatic micro processor based PLC withSCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete.With fine aggrgate,natural sand/crushed sand V.S.I.grade finely washed etc.

Bd.F.6 Page No. 300 andB.7, Page No.38

260 Cu.m.

10

Providing and casting in situ, cement concrete M-15grade of trap/granite/quartzite/gneiss metal for plinthslab, Coping to plinth or parapet as per detaileddesign and drawings including steel centering,plywood/steel formwork steel props, compaction,finishing uneven and honeycombed surface with C.M1:3 of sufficient minimum thickness to give a smoothand even surface or roughening the surface only.Newly laid concrete shall be covered by gunny bagplastic, tarpaulin etc. (Wooden centering will be notallowed). Spec No. Bd.F. 3/Page No. 288/I.S.456(2000)

85 Cu.m.



11

Providing and laying Cast in situ/Ready Mix cementconcrete M-25 of trap/ granite / quartzite/ gneissmetal for R.C.C. slabs and landings (includingsloping slab) as per detailed designs and drawingsincluding centering, formwork, cover blocks,compaction, finishing the formed surfaces withcement mortar 1:3 of sufficient minimum thickness togive a smooth and even surface or roughening ifspecial finish is to be provided and curing etc.complete.(Excluding reinforcement and structuralsteel).with fully automatic micro processor basedPLC with SCADA enabled reversible Drum Typemixer/ concrete Batch mix plant (Pan mixer) etc.complete. With fine aggrgate,natural sand/crushedsand V.S.I. grade finely washed etc.Bd.F.8 Page No. 302 and B.7, Page No.38

300 Cu.m.



12

Providing and laying Cast in situ/Ready Mix cementconcrete in M-25 of trap / quartzite /granite /gneissmetal for R.C.C. Waist slab, and steps of staircasesas per detailed design and drawings or as directedincluding steel centering, plywood/ steel formwork,steel props, laying/pumping, compaction, finishinguneven and honeycombed surface with C.M. 1:3 ofsufficient minimum thickness to give a smooth andeven surface or roughening the surface if specialfinish is to be provided and curing etc. complete.(Excluding einforcement, including coverblock).(Newly laid concrete shall be covered bygunny bag, plastic, tarpaulin etc.) with fully automaticmicro processor based PLC with SCADA enabledreversible Drum Type mixer/ concrete Batch mixplant (Pan mixer) etc. complete. With fineaggrgate,natural sand/crushed sand V.S.I. gradefinely washed etc. Bd.F.13 Page No.305 / I.S.456 (2000)

11 Cu.m.



13

Providing and laying Cast in situ/Ready Mix cementconcrete in M-25 of trap/ granite/ quartzite/ gneissmetal for R.C.C. pardi / wall of required thicknessincluding centering, formwork, cover blocks,laying/pumping, compacting and roughening them ifspecial finish is to be provided and curingcomplete.(Excluding reinforcement and structuralsteel).with fully automatic micro processor basedPLC with SCADA enabled reversible Drum Typemixer/ concrete Batch mix plant (Pan mixer) etc.complete. With fine aggrgate,natural sand/crushedsand V.S.I. grade finely washed etc.Bd.F.11 Page No. 304 and B7, page no. 38

43 Cu.m.

14

Providing and casting in situ, cement concrete M-25grade of trap/granite/quartzite/gneiss metal forR.C.C. Chajja as per detailed design and drawingsincluding steel centering plywood/steel formworksteel props, compaction, finishing uneven andhoneycombed surface with C.M 1:3 of sufficientminimum thickness to give a smooth and evensurface or roughening the surface if special finish isto be provided and curing etc. complete. ( Excludingreinforcement ) The cement Mortar 1:3 plaster isconsidered for rendering uneven and honeycombedsurface only. Newly laid concrete shall be covered bygunny bag plastic, tarpaulin etc. (Wooden centeringwill be not allowed). Spec No. Bd.F. 9/Page No.303/I.S. 456(2000)

5 Cu.m.



15

Providing and fixing in position TMT - FE - 500 barreinforcement of various diameters for R.C.C. pilecaps, footings, foundations, slabs, beams columns,canopies, staircase, newels, chajjas, lintels pardis,copings, fins, arches etc. as per detailed designs,drawings and schedules. including cutting, bending,hooking the bars, binding with wires or tack weldingand supporting as required complete.Bd.F.17, Page No. 306

115 M.T.

Bd - G : BRICK WORK

16

Providing fly ash brick masonry with conventional /I.S. type fly ash bricks in C.M. 1:6 in foundation andplinth including bailing out water manually strikingjoints, racking out joints watering and scaffolding etc.complete.

Spec. No. : As directed byEngineer-in-charge and BDG - 2 and 5

32 Cu.m.

17

Providing fly ash brick masonry with conventional /I.S. type fly ash bricks in C.M. 1:6 insuperstructureincluding striking joints, racking out joints wateringand scaffolding etc. complete.

Spec. No. : As directed by Engineer-in-chargeand BDG - 2 and 5

430 Cu.m



18

Providing Second class fly ash brick masonry withconventional / I.S. type bricks in cement mortar 1:4 inhalf brick thick wall including mild steel longitudinalreinforcement of two bars of 6 mm diameter / twohoop iron strips 25 mm x 1.60 mm at every thirdcourse, properly bent and bounded at endsscaffolding raking out joints and watering etc.complete. Spec. No. : BDG - 7 page 316

815 Sq.M

Bd - J : WATER PROOFING

19

Providing water proofing in w.c. and bath includingBB coba in all position consisting of specialisedapproved water proofing compound and material asper manufacturers specification and covering 10years guarantee on court fee stamp paper of Rs.100/- including all lead, lift and ponding test etc.complete. Spec. No. : As directed by Engineer-in-charge.

53 Cu.m.

20

Providing water proof bedding for flooring of Bath and WC 25 mm thick in C.M. 1:3 including using approved water proofing compound inspecified proportion as per manufacturers specifications for per bag of cement including leveling, curing and covering 10 years guarantee oncourt fee stamp paper of Rs.500/- including ponding test etc. complete. (As directed by Engineer in Charge)

212 Sq.m.



21

Providing waterprooffing treatment to newly laid fullycured concrete slab of terrace by applying first coatof polymer modified semi viscous paste prepared bymixing polymer of approved make (such as Masterseal 550/brush bond / roffsupercrete / webercrete /monobond / perma shield / hypercrate / master creteM 81) and cement 1:2 proportion (1 litre polymer:2Kg. cement) or Rohnex water proofing system in twocoats (1kg powder, 700 ml water and polymer jellyfor first coat & 1kg powder, 500 ml water andpolymer jelly for second coat) to a neatly cleanedand dust free concrete surface and upto 300mmover parapet wall prepared by removing loose anddeposited material with brush and water laying glassfibre mesh of 10x10 specification of approved makeover tacky surface of first coat of polymer followedby second coat in transverse direction sprinklingcoarse sand over it, followed by protectivemechanical cover of 40 mm to 75 mm. thick cementconcrete of 1:2:3

575 Sq.m.



proportion using coarse aggregate of 10 MSA andwater proofing compound of approved make andpolypropylene fibres @ 125 gm per bag of cementwithin it conforming to IS, in pannels of 3m/4m or asper site condition and filling the joints with polysulphide sealant (0.08 kg per sq.mt.) after curingincluding providing holler with drip moulds at thejunction and finishing the concrete surface with neatcement slurry, polypropylene fibres @ 125 gm perbag of cement within it confirming to IS in pannels of3m/4m or as per site condition and filling the jointswith poly sulphide sealant (0.08 kg per sq.mt.) aftercuring including providing holler with drip moulds atthe junction and finishing the concrete surface withneat cement slurry including curing as directed andponding the surfaces as directed etc. completecovering 10 years guarantee against leakproofnesson court fee stamp paper of RS. 100/- (Note: forslanting length upto 5.0 m) Spec No. As directed byEngineer-in-charge.

22

Providing and applying water proofing treatmentto bottom surface of tank and vertical surface ofbrick wall and RCC wall , elevated and overheadtank RCC / brick water tank and sump wall etc. in alldirections by using standard acrylic copolymercoating of Roof Hyguars, monopol 456 or equivalentin two coats including cleaning the surface by wirebrush, washing and drying including coveringguarantee of 10 yrs on court stamp paper of Rs. 100/-and as directed by engineer in charge. etc. complete

175 Sq.m.



Bd- L: PLASTERING AND POINTING

23

Providing internal cement plaster 6 mm thick in asingle coat in cement mortar 1:3 without neeru finishto concrete surface in all positions includingscaffolding and curing etc. complete. Bd. L.1 PageNo. 367

2765 Sq.m.

24

Providing internal cement plaster 12mm thick insingle coat in cement mortar 1:5 without neeru finishto concrete or brick surfaces, in all positionsincluding scaffolding and curing etc. complete. Bd. L.2 Page No. 368

5790 Sq.m.

25

Providing fine cement finish 1.5 mm thick over greenplaster surface including scaffolding curing etc.complete. Spec. No. : Asdirected by Engineer-in-charge.

90 Sq.m.

26

Providing external/internal cement plaster 20mmthick in a single coat in cement mortar 1:4 withoutneeru finish to concrete, brick surfaces in allpositions including scaffolding and curing. Providinggroove at joint of B.B. Masonry and concretemembers complete.

2740 Sq.m.

27

Providing groove to required size at specifiedlocation as directed by Engineer, at junction of brickmasonry wall and R.C.C. beams or column, atjunction of composite masonry, includingscaffolding, finishing, curing etc. complete. SpecNo. As directed by Engineer-in-charge

770 Rmt.



28

Providing and fixing chicken mesh / fiber mesh of 22gauge, with about 30 cm. width at the junction ofR.C.C members and brick work, of approved qualityincluding fixing mesh in position by necessary drillingin concrete /B.B.masonry and or tying by bindingwire etc. complete. Spec. No. : Asdirected by Engineer-in-charge.

3700 Rmt.

Bd - M : PAVING, FLOORING & DADO

29

Providing and laying best quality white marble slabsflooring or equivalent of size 60 cm x 45 cm and 18to 20 mm thick of approved quality vein and colourwith machine polished surface for flooring in requiredpattern on bed of C.M. 1:6 including neat white /coloured slurry, curing, polishing, cleaning complete. Spec No. Bd. M. 16/Page No. 387

100 Sq.m.

30

Providing and laying Vitrified mirror/glossy finish tiles having decorative type of size 590 millimeter to 605 millimeter x 590 millimeter to 605 millimeter of 8 to10 millimeter thickness and confirming to IS15622-2006 (Group Bla )of approved make shade and pattern for flooring n required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints curing and cleaning etc. complete.Spec No. Bd. M. 3/Page No. 380

1100 Sq.m.



31

Providing and laying Vitrified mirror/glossy finish tiles having decorative type of size 590 millimeter to 605 millimeter x 590 millimeter to 605 millimeter of 8 to10 millimeter thickness and confirming to IS15622-2006 (Group Bla )of approved make shade and pattern for dado & skirting in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints curing and cleaning etc. complete.

110 Sq.m.

32

Providing and fixing ceramic tiles of approvedquality, required size and 5.5 mm thickness for dadoand skirting in required position with ready madeadhesive mortar of approved quality in requiredposition after making the wall portion in level inplaster of C.M. 1:4 including joint filling withwhite/colour cement slurry cleaning curing complete.

560 Sq.m.

33

Providing sills / jambs / revels of granite slabs orequivalent 18 to 20 mm thick of approved qualityvein and colour with machine polished surface on abed of CM 1:4 including neat cement float fillingjoints with neat cement slurry to match the colour ofthe slabs curing,, polishing and rounding edgescleaning etc. complete. Spec No. BDM 31/p-392

80 Sq.m.

34

Providing moulding to granite / marble / kota stoneincluding polishing, rounding edges as requiredcleaning etc. complete. Spec No. : As directed byEngineer-in-charge

Half Moulding 1400 RmtFull Moulding 1100 Rmt



35

Providing and fixing ceramic tiles of approvedquality 30 cm x 30 cm x 5.5 mm thickness forflooring in required position laid on bed of C.M. 1:4including cement float, including filling joint withwhite / colour cement slurry, cleaning, curingcomplete. Spec No. : As directed by Engineer-in-charge

145 Sq.m.

36

Providing and laying in position flooring of telephoneblack / Amba White / Cat bary brown / Ruby red /Ocean Brown granite stone of approved shade andsize 18 mm to 20 mm thick on bed 1:6 cementmortar including cement floats striking joints, pointingin C.M. 1:3 curing and cleaning etc. complete.Spec. No. Bd. M. 3B / Page No.380

580 Sq.m.

37

Providing and laying flooring of 25mm. thick precastpolished chequered coloured cement tiles of size25 cm x 25 cm and 25 mm thick on bed of 1:4cement mortar including neat cement float filling,joint with neat cement slurry with approved shadesof pigment to match the colour of tiles, curing, andcleaning without border/with border / with patterncement tiles. Spec No. : Bd. M. 33 (b) /Page No. 392

510 Sq.m.



38

Providing and fixing heavy duty RUBBERMOULDED GLOSSY Coloured inter locking concrete

paving blocks of 60 mm thickness of having astrength of 300 kg/Sq.cm. of approved quality andshape on a bed of crushed sand of 25 to 30 mmthick including skirting joints and cleaning etc.complete. As directed by Engineer incharge

880 Sq.m.

Bd- P: COLOUR/WHITE WASHING

39

Providing and applying putty to new plasteredsurfaces in two coats to receive approved paint in allpositions including all materials,labour scaffoldingand curing etc. complete. As directed by Engineer in charge.

8300 Sq.m.

40

Providing and applying WHITE WASH in two coaton old and new plastered or masonry surfaces andasbestos sheet including scaffolding and preparingthe surface by brushing and brooming downcomplete. Spec No. : As directed by Engineer-in-charge

300 Sq.m.

41

Providing and applying plastic emulsion paint ofapproved quality, colour and shade to new surfacein three coats including scaffolding, preparing thesurface. (excluding primer coat) etc. complete.

BDP 6 Page No. 414 Asdirected by Engineer in charge.

8300 Sq.m.



42

Providing and applying granular textured finish1.5mm thick to old and new surfaces in decorativefinish in approved colour and shade as directed byengineer-in-charge including Two layers of base coat(spectrum or equivalent), scrapping, preparing thesurface scaffolding etc. complete.

5500 Sq.m.

Bd-T: DOORS AND WINDOWS

43

Providing and fixing country teak wood frame 60mm x100mm for second class doors with/withoutventilators windows and windows fans light andclear storey windows including all mouldings,chamfering, rounding and abauting holdfast andfinishing with one coat of primer etc. complete.Spec.No.: Bd.T.2/Page No.478

3 Cu.m.

44

Providing and fixing solid core flush door shutter insingle / double leaf 32 mm thick decorative type ofexterior grade as per detailed drawings, approvedface teak veeners 3 mm thick on both faces or asdirected, all necessary beads, mouldings and lipping,wrought iron hold fast,stainless steel fixtures andfastenings and handles on both sides and finishingwith french polish etc. complete. BD-T-36Page No. 500 and As directed by Engineer incharge.

235 Sq.m.



45

Providing and fixing M40 grade thick vibrated pullcast or similar type concrete frame with chamferconforming to I.S. 65241983 having 6 mm dia bars 3Nos. And strips @250 mm c/c and fixing in wall with6 Nos. of hold fast of 12 mm dia bars 500 mm longincluding primer and oil painting etc, complete) frame size 60 mm x 125 mm / 100 mm Asdirected by Engineer in charge.

570 Rmt.



46

Providing and Fixing 30 MM thick BOTH SIDEPRELAMINATED SOLID PANEL PVC DOOR SHUTTERconsisting of frame made out of M.S tubes of 19 guagethickness and, size 19 x 19 mm for styles and 15 x15 mmfor the top and bottom rails, M.S frame shall have a coatof metel primer of approved make and manufacture. M.Sframe shall be covered with heat mouled PVC 'C' channelmade from 5 mm (+/0.25) thick prelaminated sheet ofdensity 600 kg/cbm ,of size 30mm thickness 70mm widthout of which 50mm shall be flat and 20mm shall betapered in 45? angle on either side forming stiles ; and 5mm thick ,95 mm wide PVC sheet out of which 75 mmshall be falt and 20 mm shall be tapered in 45 on the inner side to form top and bottom rail and 115 mm wide PVCsheet out of which 75 mm shall be falt and 20 mm shallbe tapered on both sides to form lock rail.Top,bottom andlock rail shall be provided either side of the panel. Anadditional 5 mm (+/0.25) thick PVC strip of 20 mm width isto be stuck on the bottom side of the ' c ' channelprelaminated paneling of 5 mm (+/0.25) thick PVC sheetto be fitted inside the M.S. frame welded/ sealed to thestyles and rails with 5 mm (+/0.25) x 30 mm PVC sheetbeading on either side and joined together with solventcement adhesive etc ,10 mm thickness (5 mm (+/0.25) x 2 nos ) 20 mm wide cross PVC sheet as gap insert for therail and bottom rail. Door to be fixed to frames with 3 nosM.S.powder coated but hinges of size 100 mm x 25MM x2mm using 32 mm long steel screws drilled suitable topass through both the walls of the M.S tube. Otherhardwares should be fixed with 19 x 6 mm size steelscrews including fixture fasting. Complete as per directionof engineer in charge.

45 Sq.m.

47

Providing and fixing mild steel grill work for windows,ventilators etc. 20 kg/sqm as per drawing includingfixtures, necessary welding and painting with onecoats of anticorrosive paint and two coats of oilpainting complete. BD-U-1 Page No. 537

190 Sq.m.



48

Providing and fixing in position (as per 1868 / 1982)Aluminium sliding window of three tracks withrectangular pipe 95 x 38.10 x 0.90 mm at weight0.637 kg/Rmt. with window frame bottom tracksection 92 x 31.75 x 1.30 mm at weight 1.070kg/Rmt.. Top and side track section 92 x 31.75 x1.30 mm at weight 0.933 kg/Rmt. The shutter shouldbe of bearing bottom 40 x 18 x 1.25 mm at weight0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10mm at weight 0.469 kg/Rmt. and handle and topsection 40 x 18 x 1.25 mm at weight o.417 kg/Rmt.As per detailed drawings and as directed byEngineerincharge with all necessary Aluminiumsections fixtures and fastenings such as rollerbearing in nylon casting and self locking catch fittedin vertical section of shutter including 5 mm thickplain glass and aluminium mosquito net shutter withstainless steel jail with all required screws and nutsetc, complete. With powder coating with box. Asdirected by Engineer in charge.

175 Sq.m.



49

Providing and Fixing mat finish stainless steel (of302 grade ) railing with top pipe of 50 mm dia. andvertical pipe of 38 mm dia at 0.60 m c/c or asrequired and horizontal pipes of 25 mm dia in threerows, all pipes of 2 mm thick includingbuffing,fabricating fixtures and fastening includingpipe base of appropriate diameter and ball base of75 mm dia above newel post of 75 mm diameter etc.complete (Prior approval of sample and brand byEx.Engineer is necessary before use) As directedby Engineer in charge.

155 Sq.m.

50

Providing, Supplying and fixing in position anodisedextruded aluminium section of size 83 x 38 mm oras required for aluminium composite panellingincluding sheet of thickness 4 mm and of approvedshade and colour and all necessary fixtures,fastners, labours, scaffolding ,etc. complete Spec.No. As directed by Engineer In-Charge.

65 Sq.m.

ANTI-TERMITE AND PEST CONTROL

51

Providing preconstructional antitermite treatment asper I.S. 6313 (Part-II) by treating the bottom surfaceand sides of excavation at the rate of 5 litres ofemulsion concentrate of 1.0 percent ofchlorophyrifos per square meter of surface areacovering 10 years guarantee on bond paper. As directed by Engineer in charge

1030 Sq.m.



52

Providing preconstructional antitermite treatment asper I.S. 6313 (Part-II) by treating the top surface ofplinth filling at the rate of 5 litres of emulsionconcentrate at 1.0 percent of clorophyrifos persquare metre of surface area covering ten yearsguarantee on bond paper. As directed byEngineer in charge

555 Sq.m.

B) WATER SUPPLY AND SANITARY FITTINGS

53

Providing and fixing Steel Sink of size 600 mm x510 mm x 200 mm ( 1 mm thick) UPVC waste pipeupto outside face of wall or upto nahani trap coldwater chromium plated screw down bib tap, rubberplug and brass chain, making good the damagessurface, etc. complete (Prior approval of sample andbrand by Engineer is necessary before use.)

12 No

54

Providing and fixing on walls/ceiling/floors, mediumgrade G.I. Pipe(type) having embossed ISI mark onit, of required diameter with screwed sockets, joints,necessary galvanised iron fittings such as sockets,back nuts, elbow, bends, tees, reducers, enlargers,plugs, clamps etc. including necessary drilling holesin walls, slabs etc. and remarking good thedemolished portion to restore the same in originalcondition neatly and providing and applyinganticorrosive primer oil paint and two coats of oilpainting testing etc. complete. (Prior approval ofsample by Ex. Engineer is necessary before use)Spec No. : Bd. V. 5/Page No. 551

15 mm dia. 400 Mtr25 mm dia. 400 Mtr



40 mm dia. 400 Mtr

55

Providing and lying in trenches medium grade G.I.Pipe(type) having embossed ISI mark on it, ofrequired diameter with screwed sockets, joints,necessary galvanised iron fittings such as sockets,back nuts, elbow, bends, tees, reducers, enlargers,plugs, clamps etc. including necessary drilling holesin walls, slabs etc. and remarking good thedemolished portion to restore the same in originalcondition neatly and providing and applyinganticorrosive primer oil paint and two coats of oilpainting testing etc. complete. (Prior approval ofsample by Ex. Engineer is necessary before use)Spec No. : Bd. V. 5/Page No. 551

15 mm dia. 120 Mtr25 mm dia. 120 Mtr40 mm dia. 120 Mtr

56

Providing and fixing 15 mm dia. Screw down bibcock of C.P. Long body type including necessarysockets, union nut, testing etc. complete. (Priorapproval of sample by Ex. Engineer is necessarybefore use) Spec No. : Bd. V. 8/Page No. 554

72 No

57

Providing and fixing 15 mm dia. C.P. Sink cockwith raised "J" Shaped swinging casted spout ofapproved make including necessary sockets, unionnut, testing etc. complete. (Prior approval of sampleby Ex. Engineer is necessary before use) Spec No. :Bd. V. 8/Page No. 554

24 No



58

Providing and fixing screw down required dia. wheeled stop tap of brass including necessarysockets, union nut, testing etc. complete. (Priorapproval of sample & brand by Ex. Engineer isnecessary before use) Spec No. : Bd. V. 9/Page No.555

25 mm dia 12 No40 mm dia. 16 No

59

Providing and fixing Concealed C.P. angular stopcock/two way bib cock including necessarysockets, union nut, testing etc. complete. (Priorapproval of sample & brand by Ex. Engineer isnecessary before use) Spec No. : As directed byEngineer-in-charge

72 No

60

Providing and fixing UPVC SOIL / VENT / WASTESWR PIPE of required diameter conforming to I.S.13592 and I.S.-4985 to withstand continuous internalhydraulic pressure of 4 kg/cm2 including necessaryfixture and fitting such as bends, tees, single junctiondouble junction and joining with rubber ring andlubricant on wall by means of clips or in groundincluding necessary excavation, lying refilling trenchtesting etc. complete. Spec No. : As directed byEngineer-in-charge

75 mm dia. Pipe 360 Rmt110 mm dia. Pipe 360 Rmt



61

Providing and fixing 1st class white glazedearthenware "Orissa type" W.C. Pan 625 x 450 mmsize including 'P' or 'S' trap CCI soil and vent pipeupto the outside face of the wall, including 100 mmdia. CCI plug bend and exposed pipes, cutting andmaking good to the walls and floors, testing and 10liters PVC flushing cistern including necessarysocket, testing and necessary pipe connections, bedconcrete (C.C 1:2:4 ) 100 mm thick with BB cobaetc., complete. (Prior approval of sample byEngineer In-charge is necessary before use)

12 No

62

Providing and fixing European type white / Colourglazed earthenware water closet pan with UPVCseat and lid with chromium plated brass hinges andrubber buffers including UPVC and vent pipe up tothe outside face of wall 10 liter enameled low levelflushing cistern with fittings pipe stop tap brackets forfixing cistern 32 mm dia. UPVC flush pipe withfittings and clamps ,20 mm dia.UPVC overflow pipe,mosquito proof couplings G.I. chain and pulley,withc.p. health fosset / water Jet and fitting includingcutting and making good to the walls and floorstesting etc. complete.( prior approval of sample andbrand by Ex. Engineer is necessary before use)As directed by Engineer in charge.

12 No



63

Providing and fixing white glazed earthenware washHand basin of 55 cm x 40 cm size including coldwater piller tap, bracket rubber plugs and brasschain, stop tap, chromium plated bottle trap andnecessary pipe connections including UPVC wastepipe and trap upto the out side face of the wall,making good the damaged surface, testing etc.complete. (Prior approval of sample by Ex. Engineeris necessary before use) Spec No. : Bd. V. 30/PageNo. 565

24 No

64

Providing and fixing 10cm C.I. Nahani Trap includingC.I. grating bend and piece of C.I. pipe upto theoutside face of the wall complete. BDv 32Page No. 567

84 No

65

Providing and fixing 15cm x 10cm salt glazedstoneware gully trap in cement concrete 1:4:8outside the building including cast iron grating in thesink, connecting glazed stoneware pipe, brickmasonry chamber with cast iron lid and cast irongrating for the gully trap. BDv38 Page No. 572

68 No

66

Providing and fixing chromium plated towel rod16mm dia and 75cm in length including allaccessories complete. (Prior approval of sample andbrand by Ex. Engineer is necessary before use.)Spec No. : As directed by Engineer-in-charge

24 No



67

Providing and fixing 75 mm. Diameter centrifugally(Spun) C.I. soil/vent/waste pipe with necessaryfixtures and fittings such as bends, tees, singlejunctions, double junctions, slotted vent offsets onwall or in the ground including excavation, laying,refilling the trench and painting the exposed pipewith oil paint complete. Spec No. : Bd.V. 35/PageNo. 571

240 Rmt

68

Providing and fixing 450mm x 550mm size superiortype Belgium mirror with 16mm dia. nickel platedtowel rod etc. complete. As directedby Engineer in charge

24 No

69

Providing and fixing 100 mm. Diametercentrifugally (Spun) C.I. soil/vent/waste pipe withnecessary fixtures and fittings such as bends, tees,single junctions, double junctions, slotted ventoffsets on wall or in the ground including fittings,joints with length taken C.M. 1:2or lead with red leadoil paint, base coat and two coat of anticorrosivepaint including fixing the pipe on walls by means ofnail clamps. Spec No. : Bd.V. 36/Page No. 571

180 Rmt



70

Providing and fixing P.V.C. Rain water pipes of110mm outer diameter and having wall thickness of2.2 to 2.7 mm confirming to I.S. 13592-1992including proper rainwater receiving recess withP.V.C. plug, bend, necessary fittings, such as,offsets, shoes, inluding fixing the pipe on wall usingapproved wooden cleats projecting 25mm to 40mmfrom face of wall a fixing with clips of approvedquality and number ,filing the joint using rubbergasket with solvent cement and properly resting theshoe of pipes on C.C. or masonry blocks, includingnecessary scaffolding and maintenance for 3 yrs forany leakages or dislocations of pipes. All the P.V.C.fittings and additional 2 piece socket clips shall begot approved from engineer in charge etc. complete.(The contractor shall give 3 yrs guarantee bond forpayment) As directed by Engineer in charge.

180 Rmt

71

Providing and fixing100 mm dia. Chromium platedWall mixer cock of heavy duty without washer withchromium plated showers with/with telephonicarrangement including necessary supply pipes 15mmdia.and fittings like socket union, nuts, bends, valves,reducers, including necessary drilling holes in walls,slabs etc and remaking good the demolished portionto restore the same in original condition neatly andcleaning the site after completion of work, testingetc. complete. Spec No. :As directed by Engineer -in - charge.

24 No



72

Providing and constructing Brick Masonry InspectionChamber 60cm x 45cm x 90cm including 1:4:8cement concrete foundation 1:2:4 cement concretechannels half round G.S.W. pipes, Brick Masonry,plastering from inside and with frame fixed in cementconcrete with R.C.C. Cover medium duty 140 kg withframe etc complete. BDv43 Page No. 574

18 No

73

Providing and constructing Brick Masonry InspectionChamber 90cm x 45cm x 90cm including 1:4:8cement concrete foundation 1:2:4 cement concretechannels half round G.S.W. pipes, Brick Masonry,plastering from inside and with frame fixed in cementconcrete with R.C.C. Cover medium duty 140 kg withframe etc complete. BDv43 Page No. 574

15 No

74

Providing and laying Polished Shahabad StoneFlooring 20mm to 25mm thick and of required widthin plane / diamond pattern with black polishedkaddappa slab for border or any other design onabed of C.m. 1:6 including cement slurry, curingpolishing and cleaning complete.

100 Sq.m

75

Providing and fixing in required position skirting ordado of polished Shahabad stone slab 20mm to25mm thick and required width on after making thewall portion to required level with C.m. 1:4 andfixing tiles with ready made adhesive includingcement slurry, curing rubbing polishing and cleaningcomplete.

70 Sq.m



76

Cleaning of site including cutting of bushes, trees ofall girths, removing of roots of soil from the soil,Spreading of soil, Surface dressing, dismantling ofexisting structure if any (Dismantling of existing qtrbuildings), including stacking the serviceablematerial at store, and transportation of excessexcavated earth/soils from site to any other place onthe VNIT campus and including the temporarilyG.I./A.C. sheet partition for the protection duringconstruction with all framework (Cordening off thesite area) as directed etc. complete. Spec. No. Asdirected by Engineer-in-charge.

1 Job

Rain water harvesting



77

Shallow Percolation Pit providing, constructing 2.0mdeep shallow depth percolation pit comprising of1.0m diapre-cast RCC rings, 300mm thicks fillingaround outside of RCC rings (annular space )with40mm size boulders including filling of percolation pitupto 0.5m depth (from bottom up) with 25-75mmclean washed gravels followed by 0.5m depth of 10-25mm of clean washed stones followed by 0.5m ofwashed river fine aggregate (naturals and /crushedsand VSIgrade finely washed etc.) including netlonmesh between each gravel/fine aggregate(naturals and /crusheds and VSIgrade finelywashedetc.) media layer including covering with RCCslab,manhole frame & cover, PVCrungs etc.including arrangement for inlet & outlet pipe,excavation & backfilling as shown in the drawing.Therate shall be inclusive of all labour, material,wastage, scaffolding, transportation, taxes, includingall leads, lifts at all levels .All material should be ofapproved make .All works complete as per thedrawing ,technical specification and direction of theEngineer in charge

1 Nos

Contractor Director

Total Amount in Rs.

B) FURNITURE WORK

(in figure) (in words)

1

Item: Providing, making and fixing in position Modular Kitchen of size (Main Platform of 2.75m.X0.675m. & side platform of 0.60m.X0.60m) with baskets of stainless steel of Evershine NEXT or equivalent make, otta platform structure to be made up of aluminium pipe of 50mmX25mmX1.5mm of TATA, Jindal or equivalent make including fixing wooden battens inside the aluminium pipe and making the structure as per detailed drawing or as directed with 15 mm thick cement bonded partical board of Byson or equivalent make for supporting of granite, 25mm thick waterproof ply (19+6) to be used for making traulie panels and shutters duly laminated with 0.80 mm th. laminate from inside and 1 mm th. laminate of approved shade and pattern from outside. The size & no. of traulies should be as per detailed drawing, The Telescopic chanels used for traulies should be of Hettich or equivalent make, Auto closing hinges for shutters of Hettich or equivalent make, all hardware and fittings like handles etc. should be of brass with S.S. finish of approved size and pattern. The edges of traulie panels and shutters to be covered with first class C.P. beedings duly polished with melamine polish to match with the shade of laminate.

24.00 Nos

AmountItem no. Items of work Estimated

Quantity Unit Rate in Rs.

(in figure) (in words) AmountItem no. Items of work Estimated


2

Providing, making and fixing at site Wall Cabinet unit as per the detailed drawing or as directed, madeup of 18 mm commercial plywood for structure with8mm back ply support and shutters of 25mm thickply or block board, all edges of ply should becovered with 1st class C.P. beedings and laminatedwith 1MM thick Laminate on all exposed faces and0.80 mm laminate on all internal portion includingGlass work, all necessary fixtures, fittings hardware,and accessories like handles, locking arrangementas per the detailed drawing or as directed with alllead, lift etc. complete. Sample and brand of plywoodand Laminate should be approved by the engineer-in-charge before use. The exposed wooden beedingsshould be polished to match the laminate. (Frontelevational area to be measured)

30.00 Sqm.

(in figure) (in words) AmountItem no. Items of work Estimated


3

Providing, making and fixing in position WardrobeUnit with Dressing made up of 18mm commercialply for structure, 8 mm back ply for support, 25mmthick shutters of Block board, 18mm ply shelves, theinside of wardrobe to be laminated with 0.8 mm thicklaminate and 1 mm thcik laminate of approvedshade and of approved manufacture from outsidethe wardrobe as per the detailed drawing or asdirected. The edges of ply should be covered withfirst class C.P. teak wood beedings duly polishedwith melamine polish to match with the shade oflaminate. The all hardware and fittings like telescopicchannels, Auto closing hinges etc. should be ofHettich or equivalent make, handles of Brass withS.S. finish of approved design, pattern and ofrequired size, Cupboard & drawer lockes of Godrej,Europa or equivalent make, stainless steel ovalshape hanger rod, 5mm mirror glass of approvedmake to be used for dressing, shelves of 8 to 12 mmas required duly polished on edges etc. complete asper the detailed drawing or as directed by Engineer-in-charge.

300.00 Sqm.

Contractor Director

Total Amount in Rs.

C) Electrification Work

Item No. Description Estimated Quantity Unit Amount in Rs.

(In Figure) (In words)

1Supplying & erecting H.M.S. P.V.C. conduit 20 mm. dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

1728.00 Meter

2Supplying & erecting HMS P.V.C. conduit 25 mm. dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

2772.00 Meter

3

Point wiring for light/fan/bell concealed type in min 20 mm ISI marked HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLS grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/CW

360.00 Point

4

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 1 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background..

24.00 Nos

5

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

24.00 Nos

6


264.00 Nos

7

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 4 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background

12.00 Nos

8


24.00 Nos

9


24.00 Nos

Rate in Rs.

A. Internal Electrification Work

Page 1 of 10



Rate in Rs.

10


12.00 Nos

11

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 16 / 18 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

12.00 Nos

12

Supplying & erecting CRCA sheet metal one way enclosures suitable for D.P.M.C.B. /T.P. M.C.B. /F.P M.C.B. complete erected on angle iron/ G.I. frame. 36.00 Nos

13Supplying, erecting & marking DPMCB 6A to 32A, C- series (for motor/ power) in provided distribution board as per specification No. SW- SWR/MCB

36.00 Nos

14

Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/flush mounted with 2 ways forb incoming and 16 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB

12.00 Nos

15Supplying erecting and marking SPMCB 6A to 32 A C series in provided distribution board as per specifacation no SW SWR/MCB

192.00 Nos

16

Providing, erecting and commissioning 2 pole RCCB only of electromagnetic type with 30 mA sensitivity and having capacity of 63A complete as per specification no. SWRCCB/ RCCB

12.00 Nos

17Supplying & erecting mains with 3x4 sq.mm. FRLSH copper wire, in 16gauge 20 mm dia. rigid steel conduit, with continuous GI earth wire of 2.5sq.mm. as per specification No: WG-MA/MC.

1596.00 Meter

18Supplying & erecting mains with 3x10 sq.mm. FRLSH copper wire, in 16gauge 25 mm dia. rigid steel conduit, with continuous GI earth wire of 6sq.mm. as per specification No: WG-MA/MC.

408.00 Meter

Page 2 of 10



Rate in Rs.

19

Supplying and erecting fan hook box of 10 mm M.S. round bar bounded to the R.C.C. bars upto 50 mm length each side and pierced through a 16 S.W.G. thick aluminium/M.S. Bowl 100 mm dia.or equivalent square size and having depth upto 75 mm complete erected with duly painted by one coat of red oxide paint and two coats of paint erected in position and without any leakage of slurry of cement concrete on either side of the box and positioned to the bottom level of the slab.

72.00 nos

20Supplying and erecting ISI mark modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete.

72.00 Nos

21

Wiring for modular plug on board with Switch socket concealed type, copper wiring and earthing and with modular accessories as per specification No: WG-PW/CW 192.00 Nos

22Supplying and erecting ISI mark modular type switch 16 / 20 A with indicator, duly erected on provided plate and box with wiring connections complete.

84.00 Nos

23Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

84.00 Nos

24

Supplying and erecting luminous / modular type call bell indicator with plastic body, heavy duty coil and indicator lamp working on 230V A.C. supply with resetting arrangement complete erected on.

12.00 Nos

25Supplying and erecting regular/ standard model ceiling fan of 1400mm. sweep complete erected in position as per specification no. FG-FN/CF

72.00 Nos

26Supplying and erecting exhaust fan heavy duty 230 V A.C. 50 cycles 375/380 mm. 1400 RPM complete erected in position as per specification no. FG-FN/EXF

48.00 Nos

27 Supplying & installing co-axial copper cable low voltage grade RG-6 as per specification No. WG-TW 264.00 Meter

28Supplying & erecting telephone copper cable 2 pair with 0.5 mm dia. laid in provided PVC casing capping/ conduit as per specification No. WG-TW

264.00 Meter

29Supplying and erecting ISI mark modular type T.V. socket single outlet, duly erected on provided plate and box with wiring connections complete.

36.00 Nos

Page 3 of 10



Rate in Rs.

30Supplying and erecting ISI marked modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete.

12.00 Nos

31 Supplying & erecting decorative pre-wired box type fitting/batten suitable for 4' T8 LED tube light (Excluding tubelight). 276.00 Nos

32 Supplying & erecting UPVC gland/ adaptor suitable for 25/32 mm dia pvc pipe. 120.00 Nos

33 Supplying and erecting crimping type copper lugs for cable upto 16 Sq mm complete as per sepecification No. CB-CL/CU. 840.00 Nos

34Supplying and erecting UPVC reinforced flexible conduit 25mm in dia. conforming to I.S. with required number ofcouplings, PVC bushes, check nuts etc. complete

60.00 Meter

35Supplying and erecting UPVC reinforced flexible conduit31/32 mm in dia. conforming to I.S. with required number ofcouplings, PVC bushes, check nuts etc. complete.

60.00 Meter

36 Supplying & erecting 18W/20W, 230V integral type LED fitting 4' T8 LED tube light batten suitable. 276.00 Nos

-



3


23.00 Point

4Supplying and erecting ISI mark modular type Two way switch 6A / 10A (2 Module), duly erected on provided plate and box with wiring connections complete.

12.00 Nos

Sub-Total (A)

B. External Electrification Work

Page 4 of 10



Rate in Rs.

5

Supplying and erecting Iron work consisting of various section of MS and Plates Rods Bars ,MS pipes etc. for panel board or any other purposes complete with bending ,cutting , drilling and welding complete at the position with neceessary materials.

50.00 Kg

6Supplying and erecting plywood 12 mm thick fixed to wall or on provided panel board with necessary materials such as screws, wall fasteners supports, nuts bolts etc. complete

4.00 Sq.m

7

Supplying and erecting of (25x4.0,mm) size electrolyte copper patti or bar in bus bar chamber / in panel or any other purpose, 500 V with require capacity with 99.9% copper purity with fixing arrangement (like lug or bottle type lug) to both the end with high grade polyolefin insulation sleeve complete as per specification no. BCP-BB

10.00 kg

8Supplying and erecting pin type LT medium insulator 100 mm x 62 mm dia. with suitable G.I. spindle, nut, bolts complete erected.

9.00 Nos

9

Supplying and erecting Powdr coated sheet 1.6 mm (16 SWG) to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint.

6.00 Sq.mm

10

Supplying and erecting static energy meter with 240V 50 Hz. AC supply 5 to 30 A, ISI mark, accuracy class 1.0 with backlit LCD display, (measuring and display kWh, V, I, kW six month history of energy and MD in kVA ) with transparent hinge type box complete erected on polished teak wood board duly wired with required size of weather proof PVC wires duly tested by electric supply company.

28.00 Nos

11Providing pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.l. Rod complete with all materials as per specification no. EAEP

4.00 Nos

12

Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no EA-EP.

60.00 Kg

13Supplying & erecting mains with 3x4 sq.mm. FRLSH copper wire, in 16gauge 20 mm dia. rigid steel conduit, with continuous GI earth wire of 2.5sq.mm. as per specification No: WG-MA/MC.

72.00 Meter

Page 5 of 10



Rate in Rs.

14

SITC of Electric Traction Passenger Lift with• Rated capacity :- 8 Passenger/544Kg• Floors :- G+3 floor (4 Stops)• Travel :- 3 to 4.2 Meters• Location of Lift Machine:-MRL• Rated speed :- 1.0mps VS• Doors type :- COPO/TOPO Doors with frame having clear opening of 800 mm wide x 2000 mm high made from SS 304 grade sheet of 1.5mm, thick in hairline finish for car and all landing doors with SS door architraves/frames• Lift car enclosure made from SS 304 grade sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe GuardApron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc.• COP with SS face plate having metallic push buttons with Braille Code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with/without attendant key switch,OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor• Clear Car size of ......mm wide x ......mm deep x ......mm high• LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having

1.00 Nos

15

Supplying, erecting & terminating XPLE armoured cable 4 core 16 m sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no.CB-LT/AL

30.00 Meter

16

Supplying and erecting single pole and neutral distribution board (SPNDB) surface/flush mounted with 2 ways for incoming and 6 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB

1.00 Nos

17

Supplying, erecting & terminating XLPE armoured cable 3½ core 70 sq. mm. aluminium conductor with continuous 12.97 sq. mm. (8 SWG) G.I. earth wire complete erected with glands & lugs,on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

300.00 Meter

18Supplying erecting and marking SPMCB 6A to 32 A C series in provided distribution board as per specifacation no SW SWR/MCB

12.00 Nos

Page 6 of 10



Rate in Rs.

-

1

Supplying , erecting & terminating 3 x 150 sq. mm. aluminium 11 kV(E), XLPE armoured cable on wall/ceiling or laid in provided trench / pipe in an approved manner as per specification no. CBHT

520.00 Meter

2Providing and erecting Heat shrinkable indoor termination kit for 11 kV ( E ) XLPE HT cable 3x120 to 185 sq. mm. with necessary material as per specification no. CB-JT/HT

4.00 Nos

3

Making trench of suitable width and depth in soft soil for laying provided LT/HT cable of 16 sq. mm & above and covered with half round hume pipe complete as per specification no. CW-EXNCTR

260.00 Meter

4

Making trench of suitable width and depth in hard murum / tar road for laying provided LT /HTcable of 16 sq. mm & above and covered with half round hume pipe complete as per specification no. CW-EXN-CTR

40.00 Meter

5

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 120 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete

40.00 Meter

6

Supplying & laying (including excavation) 25 cm Dia half round RCC Hume pipe of standard thickness at required depth up to 90 cms. below road / ground surface, for enclosing provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet).

60.00 Meter

7

Supplying , erecting, testing & commissioning 11kV, 630A, 21 kA / 3sec, 3 way outdoor, extensible motorised SCADA compatible RMU as per electric supply company specification consisting of 2 nos. feeder with load break switch and 1 no. feeder with VCB as per specification no. SW-HTS / RMU SCADA (2LBS +1VCB)

2.00 Nos

8

Supplying, installing, testing & commissioning 3 phase, 11/0.433 kV, 50 Hz., 500 kVA, oil immersed and naturally cooled outdoor type, copper wound transformer, delta/star connected additional neutral brought out on load side, temperature rise should not exceed 40oC by thermometer in oil and 45oC by the resistance in winding at full load rating, with HV tapping (with off load tap changer) off load +5 to -10 in steps of 2.5%, with standard accessories complete with test certificate with losses below 1860 Watts at 50% load, 5300 Watts at 100% load as per IS:1180 - 2014 energy efficiency level II with necessary permissions of Electrical Inspector, as per specification no SS- TR.

1.00 Nos

Sub-Total (B)C. Transformer HT ,LT Cabling & ESS Work

Page 7 of 10



Rate in Rs.

9

Making transformer plinth (1.5 x 1.5 x 1.5) m in size with necessary excavation in ground with 150 mm. thick M- 10 PCC at the bottom and top and 250 mm. thick, burnt brick wall constructed at periphery and remaining hollow portion shall be filled with 40mm hard broken aggregate. External surface duly plastered by 12 mm thick including watering etc complete.

1.00 Nos

10

Supplying, erecting & terminating XLPE armoured cable 3½core 240 sq. mm. aluminium conductor with continuous 12.97 sq. mm. (8 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

60.00 Meter

11

Providing & erecting floor mounting, Electrical panel 14 SWG, CRCA sheet powder coated with door suitable for Four pole incoming 800A ACB , 12 ways Four pole outgoing up to 400 A MCCB-4 Nos , 200A MCCB-4 Nos,250A MCCB-2 Nos & 100A MCCB-2 Nos on iron frame in compliance of IEC 61439, as per specification no SW-SWR/MCCBPB. (Including ACB,MCCB with spreader links, 1200A power bus-bar and control busbar,800A Distribution Bus-Bar and control wiring etc. required to commissing the panel and as per IEC 61439, Digital multifunction meter ,indicators and push buttons etc.)

1.00 Nos

12

Supplying and erecting 150 kVAr, 440 V 3 phase, 50 Hz., thyrister switched micro APFC passive filter with panel (14 SWG Powder coated MS sheet) , consisting of suitable steps of APP type capacitor units with harmonic filter reactors, as per specification no CP-ED/APFC

1.00 Nos

13

Providing earthing with copper earth plate size 60 x 60 x 0.315 cmwith funnel with a wire mesh for watering and brick masonry blockC.l. cover with minimum 25 kg Carbon based environment friendly back fill Ground Enhancing compound complete with all materials,testing & recording the results as per specification no ESE -LA

4.00 Nos

14

Supply, Installation, Testing and commissioning of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete. Specification no. EA-MOBI

6.00 Nos

Page 8 of 10



Rate in Rs.

15

Supplying and erecting copper strip of required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no. EA-EP.

20.00 Kg

16

Supplying and erecting aluminium strip of required sizes used for earthing on wall and/or any other purpose with necessary aluminium clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no EAEP.

65.00 Kg

17


28.00 Point

18


5.00 Nos

19Supplying and erecting ISI mark modular type switch 16 / 20 A with indicator, duly erected on provided plate and box with wiring connections complete.

20.00 Nos

Page 9 of 10



Rate in Rs.

20Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

20.00 Nos



23Supplying and erecting regular/ standard model ceiling fan of 1400mm. sweep complete erected in position as per specification no. FG-FN/CF

7.00 Nos

24Supplying and erecting exhaust fan heavy duty 230 V A.C. 50 cycles 375/380 mm. 1400 RPM complete erected in position as per specification no. FG-FN/EXF

5.00 Nos

25


12.00 Nos

Contractor DirectorVNIT, Nagpur

GST as applicable

Sub-Total (C)

Page 10 of 10

Documents

Contractor Directorvnit.ac.in/stores/wp-content/uploads/2020/02/schedule-B.pdf · Excavation for foundation in earth, soil of all types, sand, graveland soft murum, including removing