Upload
duongdang
View
231
Download
2
Embed Size (px)
Citation preview
GERARD DANIEL WORLDWIDE
www.gerarddaniel.com
Information may change without notice. Contact your sales representativeAll information presented is subject to copyright © 2009 Gerard Daniel Worldwide
Conversion FactorsUsing Conversion Factors to Suit Your Application
Corrosion Resistance of Common Metals
Chemical Brass Copper Inconel Monel Nickel Nichrome Stainless Steel SteelAlcoholAlkalisAmmoniaAmmonia SaltsBrineCyanideHydrochloricHydrofluoricNitricSulfuric
Ratings: E = Excellent | G = Good | F = Fair | X = Not Recommended
EFXXGXFXXF
EXXXGXXFXF
EEEEEGFGGF
FEGFEXGEXG
GEFFFFFFXF
GGEEGEEFEE
GEGFXEXXEX
GEGFGGXXXX
Density of Common Metals
Metal DensitySteel (including stainless)CopperHigh Brass (70/30)Brass (80/20)Commercial Bronze (90/10)PhosphorMonelNickelAluminum (50/56)
0.2830.3220.3080.3130.3180.3180.3180.3190.096
Standard Weights on Stainless Steel Wire Cloth.
Metal FactorsHigh Brass (70/30)Commercial Bronze (90/10)Phosphor BronzePlain SteelPure NickelAluminum
107.67111.16112.00
99.03111.75
33.84
Stainless SteelThe weight in pounds of any size wire per linear foot should be determined by the following formula:Weight per linear foot = D2 x 12 x 0.7854 x 0.2830 (D) Diameter in inches; (12) Length in inches; (0.7854) Conversion factor of the area of circles; (0.2830) Density of steel in pounds per cubic inch
Alloy or Nonferrous WireThe weight in pounds should be determined by the above formula, substituting the densities asindicated below:
Width Of OpeningThe width of opening of industrial wire cloth should be determined by the following formula:Width of opening = (1-DM/M) (D) Wire diameter (M) Mesh
Open AreaThe percentage of open area of industrial wire cloth, except space cloth (indicated below), should bedetermined by the following formula:Percentage of open area = (OM)2 x 100 (O) Size of opening (M) Mesh
Open Area; Space ClothThe percentage of open area for space cloth shouldbe determined by the following formula:Percentage of open area = [O/ (O + D)]2 x 100 (O) Size of opening (D) Diameter
Special AlloysStandard weights of wire cloth in any of the followingmetals will be found to be percentages, as noted, of the standard weights on Stainless Steel wire cloth.
GERARD DANIEL WORLDWIDE
Decimal DiametersComparative Decimal Diameters for Wire Cloth
Industrial Wire Cloth Standards
Standard Wire Sizes Nearest Equivalent* Steel Gauge**
0.307”
0.283”0.263”
0.250”
0.225”0.207”0.192”0.177”0.162”
0.148”0.135”
0.120”
0.105”0.092”
0.080”0.072”0.063”
0.054”
0.047”0.041”0.035”
0.032”
0.028”
0.025”0.023”
0.3065”0.2830”
0.2625”
0.2437”0.2253”
0.2070”0.1920”0.1770”0.1620”0.1483”
0.1350”0.1205”
0.1055”
0.0915”0.0800”0.0720”
0.0625”0.0540”0.0475”
0.0410”
0.0348”
0.0317”0.0286”
0.0258”
0.0230”
01
2
34
56789
1011
12
131415
161718
19
20
2122
23
24
Standard Wire Sizes Nearest Equivalent* Steel Gauge**
0.020”
0.018”
0.017”
0.016”0.015”0.014”0.0135”
0.013”
0.012”
0.011”
0.010”0.0095”0.009”0.0085”0.0080”0.0075”0.007”
0.0065”
0.006”
0.0055”
0.005”
0.0045”
0.004”0.0035”0.003”
0.0204”
0.0181”
0.0173”
0.0162”
0.0150”0.0140”
0.0132”
0.0128”
0.0118”
0.0104”
0.0095“0.0090”0.0085“0.0080”0.0075“0.0070”0.0066“
0.0062”0.0060“0.0058”0.0055“0.0052”0.0050“0.0048”0.0046“
0.0044”
25
26
27
28
2930
31
32
33
34
35363738394041
4243444546474849
50
www.gerarddaniel.com
Information may change without notice. Contact your sales representativeAll information presented is subject to copyright © 2009 Gerard Daniel Worldwide
* Nearest Equivalent Steel Gauge (W & M Sizes) (inches)
** Steel Gauge (W & M Sizes)
Conversion Factors1 micron = 0.0000394”25.4 mm = 1”