1 | P a g e

Converting PDMS/E3D for PlantSight

2020-08-25

2 | P a g e

Contents

1. Introduction ...................................................................................................................................... 3

2. Software to download ...................................................................................................................... 3

2.1. PlantSight E3D Bridge Extractor .................................................................................................... 3

2.2. PlantSight Open 3D Model Bridge ................................................................................................ 3

3. Smart 3D and PDMS sample data ..................................................................................................... 4

4. Set Logon as a Service ....................................................................................................................... 4

5. Software Installation and configuration ........................................................................................... 8

5.1. Installation of PlantSight E3D Bridge Extractor ............................................................................. 8

5.1.1. Configure Licensing ................................................................................................................... 8

5.2. Installation of Open 3D Model Bridge ........................................................................................ 17

6. Configure PlantSight E3D Bridge Extractor ..................................................................................... 17

7. Configure the PlantSight Open 3D Model Controller ..................................................................... 21

8. Importing 3D model into PlantSight ............................................................................................... 28

3 | P a g e

1. Introduction

This document outlines the steps required to setup software required for using setup and use the

PlantSight E3D Bridge Extractor and the PlantSight Open 3D Model Bridge with PlantSight.

2. Software to download

2.1. PlantSight E3D Bridge Extractor Navigate to:

https://softwaredownloads.bentley.com/en/ProductDetails/2360

2.2. PlantSight Open 3D Model Bridge Navigate to:

https://softwaredownloads.bentley.com/en/ProductDetails/2736

4 | P a g e

3. Smart 3D and PDMS sample data

A copy of data exported from the PDMS Sample project can be found on the Teams site:

stabilizer.pdmx.xml.7z

4. Set Logon as a Service

Before installing PlantSight E3D Bridge Extractor, you must enable logon as a service for the current

user. This is required as these programs are required to run as a service.

Open Administrative Tools, select Local Security Policy and open it

5 | P a g e

Go to Local Policies and User Rights Assignment, then select Log on as a service

6 | P a g e

7 | P a g e

Add the user name and click OK

8 | P a g e

5. Software Installation and configuration

5.1. Installation of PlantSight E3D Bridge Extractor

Install e3d10080008en.exe.

5.1.1. Configure Licensing

When the install finishes, you should configure the licensing. The licensing for PlantSight E3D Bridge

Extractor now uses SES licensing.

Clicking finish will bring up the Bentley Login Client. Enter the credentials you normally use for the

CONNECTION Client.

9 | P a g e

After entering your credentials, you should get this:

10 | P a g e

Closing this window will bring up the activation wizard where you will add the licensed products you will

be using.

11 | P a g e

Select a country:

12 | P a g e

And click Next.

Now you will need to add the products that will be used. Note that when using server based licensing,

all products used on this machine will have the usage against this user.

13 | P a g e

Click “+ Add Product”

Type in “PlantSight E3D Bridge Extractor”. Make sure the selection is in the text box and then click the

check mark at the right.

14 | P a g e

You should then have this:

15 | P a g e

Click the “+ Add Product” again and this time add “PlantSight Open 3D Model Bridge”. After adding this

product, the wizard should look like this:

16 | P a g e

Click Next. You should see that the status for both products is labeled with a green checkmark.

17 | P a g e

Press close and the install of the PlantSight E3D Bridge Extractor should be complete.

5.2. Installation of Open 3D Model Bridge

Install o3db10080008en.exe.

6. Configure PlantSight E3D Bridge Extractor To configure E3D data, run “PlantSight E3D Bridge Extractor”

Ensure that the “Convert to OpenPlant EC Schema” checkbox is enabled.

If the Convert to OpenPlant EC Schema option is not selected, select and hit apply. You will be

asked to restart the service and you should accept this.

Click on “Manage Projects”

18 | P a g e

Then Click on New…

Name it “Stabilizer”

19 | P a g e

Click OK

Change the units to Metric

Click OK.

We do not need to configure this project to connect to E3D as we will use models that have

already been exported from E3D.

20 | P a g e

Click Project Folder and Windows Explorer will open up to the Stabilizer project folder.

Go into the Stabilizer folder and then the Export Files folder.

21 | P a g e

Copy stabilizer.pdmx.xml to this folder

Close the Project Repository Manager, then click OK to close the PDMx Admin. You may get this

message:

If so, click Yes.

7. Configure the PlantSight Open 3D Model Controller From the start menu find the “PlantSight Open 3D Controller”

22 | P a g e

Since it was just installed, it may be at the top of the start menu, otherwise you should be able to find it

under Bentley in the start menu.

Run the application, and the first time you run the application, it will need to authenticate you.

23 | P a g e

Part of this is to give the application permission:

24 | P a g e

At the bottom of this window is a green button labeled “Yes, Allow”. Click this button to continue.

The main window for the controller will be displayed.

25 | P a g e

Click Register and select PDMx/S3D

Select the PlantSight project that you have created:

26 | P a g e

Then click Associate.

This brings up the Create Controller window.

Give the Controller a name and use “local host” for the server site since the E3D Extractor is running on

the same machine as the controller. If this is not the case, then you can use the IP Address or the

machine name instead of local host.

You also need to set the port number. The default value is set to 32767, which is the default value for

the Smart 3D Extractor. Set the value used for the E3D Extractor, this can be confirmed by running the

PlantSight E3D Extractor Admin application.

27 | P a g e

You can see that the default value is 32770.

Once you finish updating the fields for the controller it should look something like this:

Then click Add.

28 | P a g e

You will see now that you have added a controller to the PlantSight_Project.

This means that anyone who accesses the “PlantSight_Project” and then goes to import a 3D Model will

see that they can import PDMS or E3D data from this machine.

8. Importing 3D model into PlantSight

Go to https://plantsight.bentley.com/ and enter your project.

29 | P a g e

Then click on Acquisition, once that appears, click New Import and select 3D.

30 | P a g e

Fill in the required fields. The names for the Controller and Project should match what you have added

in previous steps.

Once these fields have been filled in, click Start Import.

The portal will update to show that the job was started.

31 | P a g e

To view more detailed progress of the conversion, you can go back to the controller and switch to the

jobs monitor. If the job has already started, you should see something similar:

32 | P a g e

You can also see progress of the data conversion from the E3D Extractor by going to the Session Monitor

of the PlantSight E3D Bridge Extractor Admin application:

When a conversion from E3D is started the following steps should happen:

33 | P a g e

1) If connected directly to the E3D project, the selected location in the project hierarchy will be

exported to a pdmx.xml file.

2) A pdmx.xml file will be converted using the E3D Bridge Extractor, this file will either have come

from the previous step, or if exports have already been made from the file stored in the E3D

Extractor project.

3) The PlantSight Open 3D Model Bridge will convert the output from the previous step into the

PlantSight project.