©Copyright Lotronic 2014 LAS1000RGB-5IN1 1 · output power. Always set up and install all laser effects so that all laser light is at least 3 meters (9.8 feet) above the f loor

LLAASSEERR SSHHOOWW SSYYSSTTEEMM

EEFFFFEETT LLAASSEERR RRVVBB

RRGGBB LLAASSEERREEFFFFEEKKTT

EEFFEECCTT LLAASSEERR RRGGBB

SSIISSTTEEMMAA LLAASSEERR

RReeff..:: LLAASS11000000RRGGBB--55IINN11 ((1155--11116688))

UUSSEERR’’SS MMAANNUUAALL

MMAANNUUEELL DD’’UUTTIILLIISSAATTIIOONN

BBEEDDIIEENNUUNNGGSSAANNLLEEIITTUUNNGG

HHAANNDDLLEEIIDDIINNGG

NNAAVVOODDIILLAA ZZAA UUPPOORRAABBOO

MMAANNUUAALL DDEE UUTTIILLIIZZAARREE

MMAANNUUAALL DDEE IINNSSTTRRUUÇÇÕÕEESS

©Copyright Lotronic 2014 LAS1000RGB-5IN1 1

GB - This LASER effect is built for PROFESSIONAL use only. It must be used and controlled by a professional in sufficiently large premises because of its high output power. Always set up and install all laser effects so that all laser light is at least 3 meters (9.8 feet) above the floor. Never create a fixed point.

F - Cet effet LASER est un appareil conçu uniquement pour un usage PROFESSIONNEL. Il doit utilisé et installé par un professionnel à une hauteur minimale de 3m dans des salles suffisamment grandes en raison de sa puissance importante. Toujours installer et configurer le laser de sorte que tous les effets du laser sont au moins à 3 mètres au-dessus du sol. Ne jamais créer de point fixe. D – Dieser LASER Effekt ist nur für GEWERBLICHEN Gebrauch. Aufgrund seiner hohen Ausgangsleistung darf das Gerät nur von einem Fachmann in ausreichend großen Räumen installiert und betrieben werden. Es muss in mindesten 3m Bodenhöhe angebracht werden. Der Strahl darf auf keinen Fall auf einen festen Punkt gerichtet sein. NL - Dit LASER effect is alleen voor professioneel gebruik. Door zijn hoge vermogen mag het apparaat alleen van een specialist in voldoende grote ruimten worden geïnstalleerd en bediend. Het moet worden aangebracht in tenminste 3m vloerhoogte. In geen geval de beam op een vast punt richten. PT - Este efeito LASER foi desenhado apenas para uso PROFISSIONAL. Deve ser usado e controlado por um profissional em locais grandes devido à sua elevada potência de saída. Configurar sempre e instalar todos os efeitos laser de modo a que a luz do laser esteja a pelo menos 3 metros (9,8 pés) do chão. Nunca crie um ponto fixo. RO - Acest efect LASER este construit numai pentru uz PROFESIONAL. Acesta trebuie utilizat si controlat de catre un profesionist in spatii suficient de mari, din cauza puterii sale mari de iesire. Intotdeauna setati si instalati toate efectele laser, astfel incat toate luminile laser sa fie la cel putin 3 metri deasupra podelei. Nu creati un punct fix.

GB-LASER RADIATION !

DANGEROUS EXPOSURE TO LASER RADIATION CLASS 3B LASER

F-RAYONNEMENT LASER ! EXPOSITION AU FAISCEAU DANGEREUSE APPAREIL À LASER DE CLASSE 3B

D-LASERSTRAHLEN ! GEFÄHRLICHE AUSSETZUNG AN LASERSTRAHLEN LASERKLASSE 3B

NL-LASERSTRALEN! GEVAARLIJKE BLOOTSTELLING AAN LASERLICHT LASER CLASSE 3B

PT-RADIAÇÃO LASER! EXPOSIÇÃO PERIGOSA A RADIAÇÃO LASER LASER DE CLASSE 3B RO-RADIATII LASER! EXPUNERE PERICULOASA LA RADIATII LASER LASER CLASA 3B


Thank you for purchasing this product. Please read user guide for safety and operations information before using the product. Keep this manual for future reference. This product can create perfect laser programs and effects since it has passed a series of strictly tests before delivery. Please check the attachments listed on the page after opening the carton. In the event of carton damage or attachment missing in transit, please contact your dealer or our after sales service department. Technical specifications 1. Voltage: AC100-240V, 50Hz/60Hz, Fuse: 2A/250V 2. Rated Power: 100W 3. Laser diode: DPSS, green 532nm 100mW, red 650nm 300mW, blue 450nm 800mW 4. Laser power: 1000mW 5. Scanner: 20K high speed scanner 6. Control mode: sound control/auto/DMX/ ILDA 7. DMX channel: 19 channels 8. Dimensions: 340mm x 250mm x 150mm 9. Net weight: 4.5kg 10. Gross weight: 5.5kg

Warning Do not expose the human eye direct to laser beam. Do not turn on and off the unit frequently. Before using this unit make sure the power supply is grounded. This unit is intended for indoor use only and should be prevented from water, moisture and shakes. The

working temperature of this unit is 18-30°C, do not use this continuously over 4 hours, otherwise it shortens the lifetime of the unit.

Use cleaning tissue to remove the dust absorbed on the external lenses periodically to optimize light output. Do not remove or break the warranty label, otherwise it void the warranty. Always replace with the exact same type fuse, replacement with anything other than the specified fuse can

cause fire or electric shock and damage your unit, and will void your manufactures warranty. Function setting When laser is powered on, LCD monitor on rear panel shows the current operating stand-alone mode or DMX address of DMX mode. It is very easy to set and change the operating mode of the laser via the LCD control panel. After every reset and saving, the new mode information will be shown on LCD monitor at next power on.

Mode Option, to choose the operating mode of laser Confirmation, to store the current menu of confirm the current function

UP/DOWN, to change operating mode, parameter or DMX address

GB


OPERATION

MODE LCD DISPLAY DESCRIPTION

STAND ALONE MODE PREPROGRAMMED EFFECT

MODE:AUTO Mixed 5 effect Auto Show with Mixed 5 effect

MODE:AUTO Laser 3D Laser 3D Effect Auto Show

MODE:AUTO Scanned Beam Scanned Beam Effect Auto Show

MODE:AUTO Laser Lumia Laser Lumia Effect Auto Show

MODE:AUTO Burst Grating Burst Grating Effect Auto Show

MODE:AUTO Laser Universal Laser Universal Effect Auto Show

MODE:SOUND Mixed 5 effect Sound Show with Mixed 5 effect

MODE:SOUND Laser 3D Laser 3D Effect Sound Show

MODE:SOUND Scanned Beam Scanned Beam Effect Sound Show

MODE:SOUND Laser Lumia Laser Lumia Effect Sound Show

MODE:SOUND Burst Grating Burst Grating Effect Sound Show

MODE:SOUND Laser Universal Laser Universal Effect Sound Show

SOUND MODE:SENSITIVITY ▐▐▐▐▐▐▐▐▐▐ Set microphone sensitivity

DMX MODE: signal 001 The laser is working in DMX MODE.

SLAVE MODE: signal SLAVE The laser is working in SLAVE MODE

MIRROR MODE:MIRROR SY:Y SX:Y The laser scanned world

Attention In preprogrammed standalone SOUND SHOW mode, the laser beam will be blank-out in 10 seconds

without AUDIO/MIC activated signal.


SOUND ACTIVATED MODE: Sensitivity Setting Press FUNC until S 6 is displayed Press UP/DOWN to set the microphone sensitivity. S 0 is no sound activation, from S 1 to S 9, the sensitivity level is

getting more sensitive. Press ENTER to confirm and save the setting. DMX Control Press FUNC to enter MODE selection Press until the LCD panel shows 001 Press ENTER to confirm setting The laser is working in DMX MODE. Set the DMX address via the UP and DOWN buttons Slave Operation Press FUNC to enter MODE selection Press until the LCD panel shows SLAVE Press ENTER to confirm setting The laser is working in SLAVE MODE. Connect MASTER laser to several SLAVE lasers via a DMX cable, SLAVE lasers are doing exactly the same laser show as MASTER laser. Please check below for DMX cable connection for reference. DMX512 1. Install the units in a suitable position (laying or appending). 2. Use standard XLR microphone cable chain your units together via the XLR connector on the rear of the units. For longer cable runs we suggest a terminator at the last fixture. 3. Assign a DMX address to each the unit using dipswitches; see the "DMX Address Quick Reference Char». (All units set to #1 and #10 on will be OK) 4. Turn on all units' power, the units begins reset, then the unit begins working. 5. Use DMX console to control your units.

PATTERN MIRROR REVERSE SETTING Press FUNC to enter MODE selection Till to below LCD display is shown in LCD panel and the laser will show pattern right side. Press ENTER to confirm the setting. With help of UP button, the laser scanned world in x direction could be reversed, as the graphic as below. With help of DOWN button, the laser scanned world in y direction could be reversed, as the graphic as below.

Please note: Besides the LCD programmed mirror reverse setting, the laser scanned world could be set by ILDA control panel.

ILDA Control Mode This unit has an ILDA DB25 port that allows the unit to be PC-controlled. When a 25-pin lead is connected, the

laser will be PC controlled. When the lead is disconnected, the laser will return to the last operating mode.


DMX Channels Chart DMX Channels Chart When ILDA is connected

CHANNEL VALUE DESCRIPTION

CH1 Grating Rotation

000-004 No grating rotating

005-127 Clockwise grating rotating


134-255 Anticlockwise grating rotating

CH2 Grating Effect

000-031 Laser 3D Effect

032-063 Scanned Beam Effect (Pattern Effect)

064-095 Laser Lumia Effect


128-159 Burst Grating Effect


192-223 Laser Universal Effect

224-255 Scanned Beam Effect (Pattern Effect) DMX Channels Chart When ILDA is NOT connected

CHANNEL VALUE FUNCTION

CH 1 MODE

000-018 Laser OFF

019-036 AUT Auto Show with Mixed 5 effect

037-054 A3D Laser 3D Effect Auto Show

055-072 AUB Scanned Beam Effect Auto Show

073-090 AUL Laser Lumia Effect Auto Show

091-108 AUN Burst Grating Effect Auto Show

109-126 AUO Laser Universal Effect Auto Show

127-144 SOU Sound Show with Mixed 5 Effect

145-162 S3D Sound show with LASER 3D

163-180 SOB Sound show with Scanned Beam

181-198 SOL Sound show with LASER LUMIA

199-216 SON Sound show with Burst Grating

217-234 SOO Sound show with Laser Universal

235-255 DMX MODE


CH 2 GROUP

000-051 1 Group Patterns.

052-103 2 Group Patterns




CH 3 PATTERN 000-255 Every 16 for 1 Group, total 16 patterns.

CH 4 COLOR

000-007 Original

008-015 Red

016-023 Green

024-031 Yellow

032-039 Blue

040-047 Purple

048-055 Light Blue

056-063 White

064-111 Color Rolling

112-159 Color Jumping

160-127 Color Moving

208-255 Strobing

CH 5 CLIPING

000 Full pattern without clipping

001-127 0%~99% fixed pattern clipped

128-255 Clipping Speed

CH 6 ZOOMING

000-127 100%-5% fixed pattern zoomed

128-169 Zooming IN

170-209 Zooming OUT

210-255 Alternately Zooming

CH 7 ZOOM SPEED 000-255 Fast to Slow

CH 8 Y AXIS ROLLING

000-127 0 -359 degree fixed Y axis rolled

128-191 Clockwise rolling

192-255 Anticlockwise rolling

CH 9 ROLL SPEED 0-255 Fast to Slow

CH 10 X AXIS ROLLING

000-127 0 -359 degree fixed X axis rolled





CH 12 Z AXIS ROLLING

000-127 0 -359 degree fixed Z axis rolled







CH 14 Y AXIS MOVING

000-127 128 different fixed position on X axis

128-191 Clockwise moving

192-255 Anticlockwise moving

CH 15 MOVE SPEED 0-255 Fast to Slow

CH 16 X AXIS MOVING

000-127 128 different fixed position on Y axis









CH19 Different effect










PATTERN LIST

DMX 1 2 3 4 5

000-015

016-031

032-047

048-063

064-079

080-095

096-111

112-127

128-143

144-159

160-175

176-191

192-207

208-223

224-239

240-255

Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your dealer about the way to proceed.


MANUEL D’UTILISATION Lire attentivement le manuel avant la première mise en service et le conserver pour référence ultérieur. Cet appareil a quitté l’usine en parfait état après avoir passé une série de contrôles de qualité très stricts. Vérifiez le contenu à l’ouverture de l’emballage CARACTERISTIQUES TECHNIQUES 1. Alimentation: 110/220V, 50/60Hz, Fusible : 2A/250V 2. Consommation : 100W 3. Diode laser: DPSS, vert 532nm 100mW, rouge 650nm 300mW, bleu 450nm 800mW 4. Puissance du laser : 1000mW 5. Moteur : Scanner haute vitesse 20 kpps 6. Modes de fonctionnement: Activation audio, automatique, DMX, ILDA 7. Canaux DMX : 19 8. Dimensions : 340 x250 x 150mm 9. Poids net : 4,5kg 10. Poids brut : 5,5kg

AVERTISSEMENTS o Ne pas exposer l’œil humain au rayon laser. o Ne mettre fréquemment l’appareil sous et hors tension. o Cet appareil doit être relié à la masse. o Uniquement pour utilisation à l’intérieur. Tenir à l’abri de l’eau, de l’humidité et de secousses. La température

de fonctionnement est de 18-30°C. Ne pas utiliser l’appareil plus de 4 jour en continue sous peine de diminuer sa durée de vie.

o Nettoyez régulièrement la lentille extérieure avec un chiffon propre pour retirer la poussière accumulée et optimiser la puissance lumineuse.

o Ne pas retirer l’étiquette de garantie sous peine d’invalider la garantie. o Remplacez le fusible uniquement par un neuf en tous points identique au fusible d’origine. Un autre fusible

peut provoquer un incendie ou un choc électrique et endommager l’appareil. Réglage des fonctions When laser is powered on, LCD monitor on rear panel shows the current operating stand-alone mode or DMX address of DMX mode. It is very easy to set and change the operating mode of the laser via the LCD control panel. After every reset and saving, the new mode information will be shown on LCD monitor at next power on.

Mode Option, to choose the operating mode of laser Confirmation, to store the current menu of confirm the current function

UP/DOWN, to change operating mode, parameter or DMX address

F


OPERATION

MODE LCD DISPLAY DESCRIPTION

STAND ALONE MODE PREPROGRAMMED EFFECT













SOUND MODE:SENSITIVITY ▐▐▐▐▐▐▐▐▐▐ Set microphone sensitivity

DMX MODE: signal 001 The laser is working in DMX MODE.

SLAVE MODE: signal SLAVE The laser is working in SLAVE MODE

MIRROR MODE:MIRROR SY:Y SX:Y The laser scanned world

Attention In preprogrammed standalone SOUND SHOW mode, the laser beam will be blank-out in 10 seconds

without AUDIO/MIC activated signal.


SOUND ACTIVATED MODE: Sensitivity Setting Press FUNC until S 6 is displayed Press UP/DOWN to set the microphone sensitivity. S 0 is no sound activation, from S 1 to S 9, the sensitivity level is

getting more sensitive. Press ENTER to confirm and save the setting. DMX Control Press FUNC to enter MODE selection Press until the LCD panel shows 001 Press ENTER to confirm setting The laser is working in DMX MODE. Set the DMX address via the UP and DOWN buttons Slave Operation Press FUNC to enter MODE selection Press until the LCD panel shows SLAVE Press ENTER to confirm setting The laser is working in SLAVE MODE. Connect MASTER laser to several SLAVE lasers via a DMX cable, SLAVE lasers are doing exactly the same laser show as MASTER laser. Please check below for DMX cable connection for reference. Fonctionnement DMX Ce mode vous permet de commander l’effet par le biais d’une console DMX512. 1. Installez les appareils dans une position appropriée (couché ou suspendu). 2. Reliez les appareils ensemble au moyen d’un cordon microphone XLR standard à l’arrière des appareils.

Lorsque plusieurs appareils sont connectés en série, nous recommandons de poser une résistance de fin de ligne sur la sortie du dernier appareil.

3. Affectez une adresse DMX à chaque appareil au moyen des commutateurs DIP. Voir charte des adresses DMX. Réglez les commutateurs DIP n° 1 et n° 10 sur ON.

4. Mettez tous les appareils sous tension. Ils commencent à exécuter une remise à zéro et commencent ensuite à fonctionner.

5. Commandez les appareils à l’aide d’une console DMX.

PATTERN MIRROR REVERSE SETTING Press FUNC to enter MODE selection Till to below LCD display is shown in LCD panel and the laser will show pattern right side. Press ENTER to confirm the setting. With help of UP button, the laser scanned world in x direction could be reversed, as the graphic as below. With help of DOWN button, the laser scanned world in y direction could be reversed, as the graphic as below.

Please note: Besides the LCD programmed mirror reverse setting, the laser scanned world could be set by ILDA control panel.

ILDA Control Mode This unit has an ILDA DB25 port that allows the unit to be PC-controlled. When a 25-pin lead is connected, the

laser will be PC controlled. When the lead is disconnected, the laser will return to the last operating mode.


DMX Channels Chart DMX Channels Chart When ILDA is connected

CHANNEL VALUE DESCRIPTION






CH2 Grating Effect








224-255 Scanned Beam Effect (Pattern Effect) DMX Channels Chart When ILDA is NOT connected

CHANNEL VALUE FUNCTION

CH 1 MODE

000-018 Laser OFF














235-255 DMX MODE

CH 2 GROUP







CH 4 COLOR

000-007 Original

008-015 Red

016-023 Green

024-031 Yellow

032-039 Blue

040-047 Purple

048-055 Light Blue

056-063 White




208-255 Strobing

CH 5 CLIPING




CH 6 ZOOMING


128-169 Zooming IN

170-209 Zooming OUT



CH 8 Y AXIS ROLLING



















CH 14 Y AXIS MOVING





CH 16 X AXIS MOVING




















PATTERN LIST

DMX 1 2 3 4 5

000-015

016-031

032-047

048-063

064-079

080-095

096-111

112-127

128-143

144-159

160-175

176-191

192-207

208-223

224-239

240-255

NOTE IMPORTANTE : Les produits électriques ne doivent pas être mis au rebut avec les ordures ménagères. Veuillez les faire recycler là où il existe des centres pour cela. Consultez les autorités locales ou votre revendeur sur la façon de les recycler.


ANLEITUNG Vor der ersten Inbetriebnahme die Anleitung durchlesen, um das Gerät sicher und richtig zu bedienen. Alle Anweisungen und Hinweise müssen genau befolgt werden. Das Gerät wurde zahlreichen strengen Qualitätskontrollen unterworfen und hat unser Werk in einwandfreiem Betriebszustand verlassen. Packen Sie das Gerät aus und untersuchen Sie es auf eventuelle Transportschäden. Die Verpackung muss folgende Teile enthalten: Warnhinweise 1. Nicht in den Laserstrahl blicken. 2. Das Gerät nicht kurz hintereinander ein- und ausschalten. 3. Das Gerät muss geerdet sein. 4. Nur für Innengebrauch. Vor Wasser, Feuchtigkeit und Erschütterungen schützen. Die Betriebstemperatur

beträgt 18-30°C. Nicht länger als 4 Stunden ununterbrochen benutzen, da sich sonst die Lebensdauer erheblich verkürzt.

5. Die Linse regelmäßig mit einem sauberen Tuch abwischen, um den angesammelten Staub zu entfernen und die Leuchtkraft zu erhalten.

6. Nicht das Garantieschild entfernen, da sonst der Garantieanspruch erlischt. 7. Die Sicherung nur durch eine identische ersetzen, da sonst Brand- und Stromschlaggefahr besteht.

Technische Daten 1. Versorgung: AC110/220V, 50/60Hz 2. Verbrauch: 100W 3. Laserdiode: DPSS, grün 532nm 100mW, rot 650nm 300mW, blau 450nm 8000mW 4. Laserleistung: 1000mW 5. Motor: 20Kpps Hochgeschwindigkeitsscanner 6. Betriebsart: Audio/Automatik/DMX/ILDA 7. 19 DMX Kanäle 8. Abmessungen: 340 x250 x 150mm 9. Nettogewicht: 4,5kg 10. Bruttogewicht: 5.5kg Einstellung der Funktionen Beim Einschalten des Geräts erscheinen auf dem LCD auf der Rückseite die aktuelle Betriebsart oder die DMX Adresse, wenn sich der Laser im DMX Betrieb befand. Die Betriebsarten und Einstellungen können schnell und einfach über das Bedienfeld vorgenommen werden. Die neuen Informationen erscheinen beim nächsten Einschalten auf dem Display.

Einstellung der Betriebsarten. Bestätigung und Speicherung der Einstellungen

UP/DOWN: Wahl der Werte, Parameter bzw. Einstellung der DMX Adresse

D


BEDIENUNG

BETRIEBSART LCD DISPLAY BESCHREIBUNG

AUTOMATISCHER BETRIEB, VORPROGRAMMIERTE EFFEKTE













KLANGAKTIVIERT MODE:EMPFINDLICHKEIT ▐▐▐▐▐▐▐▐▐▐ Einstellung der Mikrofonempfindlichkeit

DMX MODE: Signal 001 Der Laser arbeitet im DMX Betrieb.

SLAVE MODE: Signal SLAVE Der Laser arbeitet im SLAVE Betrieb

SPIEGEL MODE:MIRROR SY:Y SX:Y LASER SCANNED WORLD

Hinweis: Im vorprogrammierten, automatischen SOUND Betrieb schaltet sich der Laser nach 10 Sekunden aus,

wenn kein AUDIO/ MIKROFON Signal anliegt.


MUSIKAKTVIERTER BETRIEB: Einstellung der Empfindlichkeit FUNC Taste drücken, bis S 6 erscheint Mit den UP/DOWN Tasten die Mikrofonempfindlichkeit einstellen.. S 0 bedeutet keine Klangaktivierung. Von S 1 bis S 9

erhöht sich die Empfindlichkeit. Mit ENTER die Einstellung bestätigen und speichern. DMX Steuerung Auf FUNC drücken, um die Betriebsart (MODE) zu wählen Drücken bis 001 auf dem Display erscheint Mit ENTER die Einstellung bestätigen Der Laser arbeitet nun im DMX Betrieb. Mit den UP und DOWN Tasten die DMX Adresse einstellen. Slave Betrieb Auf FUNC drücken, um die Betriebsart (MODE) zu wählen Drücken bis SLAVE auf dem Display erscheint Mit ENTER die Einstellung bestätigen Der Laser arbeitet nun im Slave-Betrieb. Den MASTER Laser an mehrere SLAVE Laser über ein DMX Kabel anschließen. Die SLAVE Laser folgen dem Master und tun genau dasselbe. S; nachstehend wie die Geräte angeschlossen werden müssen. Universaler DMX Betrieb In dieser Betriebsart wird das Gerät von einer DMX512 Konsole gesteuert. 1. Installieren Sie das Gerät in einer geeigneten Stellung (liegend oder hängend). 2. Mit einem Standard XLR Mikrofonkabel die Geräte über die XLR Buchse auf der Rückseite miteinander

verbinden. Wenn mehrere Geräte benutzt werden, muss ein Endwiderstand an die XLR Ausgangsbuchse des letzten Geräts angebracht werden.

3. Geben Sie jedem Gerät mittels der DIP Schalter eine DMX Adresse (s. DMX Tabelle). Stellen Sie alle DIP Schalter Nr. 1 und Nr. 10 auf ON.

4. Schalten Sie alle Geräte ein. Nach dem Reset sind sie einsatzbereit. 5. Mit der DMX Konsole die Geräte steuern.

SPIEGELVERKEHRTE MUSTER Auf FUNC drücken, um die Betriebsart (MODE) zu wählen Drücken bis die nachstehende Zeichnung auf dem Display erscheint. Der Laser zeigt die rechte Seite des

Musters. Mit ENTER die Einstellung bestätigen. Mit der UP Taste das Muster um die X-Achse drehen. Mit der DOWN Taste das Muster um die Y-Achse drehen.

Hinweis: Außer der über das Display programmierten Spiegelung kann die Laser Scanned World auch über ILDA eingestellt werden.

ILDA Steuerung Das Gerät besitzt einen ILDA Sub-D25 Verbinder, über den der Laser PC-gesteuert werden kann. Wenn ein

25-pol. Verbinder angeschlossen ist, wird der Laser über den PC gesteuert. Wenn kein Sub-D25 Verbinder angeschlossen ist, arbeitet der Laser in der zuletzt eingestellten Betriebsart.


DMX Kanaltabelle DMX Kanaltabelle, wenn der ILDA Verbinder angeschlossen ist:

KANAL WERT BESCHREIBUNG






CH2 Grating Effect








224-255 Scanned Beam Effect (Pattern Effect) DMX Kanaltabelle, wenn kein Sub-D25 Verbinder angeschlossen ist:

KANAL WERT BESCHREIBUNG

CH 1 MODE

000-018 Laser OFF













235-255 DMX MODE


CH 2 GROUP







CH 4 COLOR

000-007 Original

008-015 Red

016-023 Green

024-031 Yellow

032-039 Blue

040-047 Purple

048-055 Light Blue

056-063 White




208-255 Strobing

CH 5 CLIPING




CH 6 ZOOMING


128-169 Zooming IN

170-209 Zooming OUT



CH 8 Y AXIS ROLLING



















CH 14 Y AXIS MOVING





CH 16 X AXIS MOVING




















PATTERN LIST

DMX 1 2 3 4 5

000-015

016-031

032-047

048-063

064-079

080-095

096-111

112-127

128-143

144-159

160-175

176-191

192-207

208-223

224-239

240-255

WICHTIGER HINWEIS: Elektrogeräte gehören nicht in den Hausmüll. Sie müssen in speziellen Betrieben recycelt werden. Bringen Sie sie zu einer speziellen Entsorgungsstelle für Elektrokleingeräte (Wertstoffhof)!


HANDLEIDING Bedankt voor de aankoop van onze product. Lees deze handleiding aandachtig door alvorens U het product gebruikt. Bewaar de handleiding op. Dit product creëert perfecte laser programma’s en effecten en heeft een rij van strikte tests doorgelopen.. Specificaties 1. Voeding: AC100-240V, 50Hz/60Hz, Zekering: 2A/250V 2. Opgenomen vermogen: 100W 3. Laser diode: DPSS, groen 532nm 100mW, rood 650nm 300mW, blauw 450nm 800mW 4. Laser vermogen: 1000mW 5. Scanner: 20K high speed scanner 6. Werkingsmodi: muziek bestuurd/auto/DMX/ ILDA 7. DMX kanalen: 19 kanalen 8. Afmetingen: 340mm x 250mm x 150mm 9. Nettogewicht: 4.5kg 10. Brutogewicht: 5.5kg

Waarschuwingen 1. Nooit in de laserstraal kijken. 2. Nooit het toestel kort achtereenvolgens aan en uit schakelen. 3. Alleen op een stopcontact met randaarde aansluiten. 4. Alleen voor binnen gebruik. Tegen water, vochtigheid en trillingen beschermen. De werkingstemperatuur is

18-30°C. Na 10 minuten gebruik 30 minuten pauze maken. 5. Reinig de lens regelmatig d.m.v. een zuivere doek om vuil te verwijderen en het lichtvermogen te bewaren. 6. De zekering alleen door een identieke vervangen om vuur en elektrische schokken te vermijden. 7. Voor reparaties en onderhoudswerken het toestel van het lichtnet ontkoppelen. Alle reparaties alleen door een

vakman doorvoeren laten. Nooit het toestel zelfs repareren. Het toestel omvat geen van de gebruiker vervangbare onderdelen.

8. Nooit het toestel gebruiken wanneer het net kabel beschadigd is. Een beschadigde stroomkabel onmiddellijk van een vakman vervangen laten.

Functie instelling Wanneer de laser wordt ingeschakeld, toont de LCD op de achterzijde de huidige operationele stand-alone modus of DMX-adres in DMX modus. Het is heel eenvoudig de modus van de laser via het LCD-bedieningspaneel in te stellen of te veranderen. Na elke reset en opslaan, wordt de nieuwe modus informatie op het LCD weergegeven.

Drukken om de werkingsmodi van de laser te kiezen Bevestiging van de instellingen

UP/DOWN: Verandering van de werkingsmodi, instelling of DMX adres

NL


WERKING

MODUS LCD DISPLAY OMSCHRIJVING

AUTOMATISCHE WERKING MET VOOR- GEPROGRAMMEERDE EFFECTEN













MUZIEKBESTURING MODE:SENSITIVITY ▐▐▐▐▐▐▐▐▐▐ Instelling van de microfoon gevoeligheid

DMX MODE: signal 001 De laser werkt in DMX MODE.

SLAVE MODE: signal SLAVE De laser werkt in SLAVE MODE

SPIEGEL MODE:MIRROR SY:Y SX:Y LASER SCANNED WORLD

Let op: In voorgeprogrammeerde standalone SOUND modus schakelt de laser na 10 seconden uit indien geen

geluid/microfoonsignaal aanwezig is.


GELUIDGEACTIVEERDE MODUS: Instelling van de gevoeligheid Druk op FUNC totdat S 6 verschijnt Stel de microfoongevoeligheid d.m.v. de UP/DOWN toetsen in. S 0 bedoelt geen geluidactivering, van S 1 tot S 9, wordt de

microfoon gevoeliger. Instellingen met ENTER bevestigen en opslaan. DMX Controle Druk op FUNC om de MODE te kiezen Druk totdat 001 op de display verschijnt. Druk ENTER om de instelling te bevestigen De laser werkt nu in DMX modus. Stel de DMX adres d.m.v. de UP en DOWN toetsen in. Slave modus DMX Controle Druk op FUNC om de MODE te kiezen Druk totdat SLAVE op de display verschijnt. Druk ENTER om de instelling te bevestigen De laser werkt nu in SLAVE modus. Sluit een MASTER laser op meerdere SLAVE lasers d.m.v. een DMX kabel aan. De slaves doen hetzelfde als de master. Zie kabelaansluiting beneden. DMX modus 1. Installeer het toestel in een geschikte positie. 2. Verbind de toestellen d.m.v. een standard XLR microfoon kabel via de XLR contra op de achterkant. Indien U

meerdere toestellen aan elkaar aansluit, installeer een aardweerstand op de laatste XLR uitgang. 3. Geef elk toestel een DMX adres (zie tabel). 4. Schakel alle toestellen aan. Na de reset zijn ze klaar voor gebruik. 5. Bestuur de toestellen via de DMX controller.

INSTELLING VAN DE PATROONSPIEGELING Druk op FUNC om de MODE te kiezen Druk totdat de rechterkant van een patroon op de display verschijnt. Druk ENTER om de instelling te bevestigen Druk op UP om de LASER SCANNED WORLD om de x-as te draaien. Druk up DOWN om de LASER SCANNED WORLD om de y-as te draaien.

Let op: De spiegeling van de LASER SCANNED WORLD kan ook via ILDA gedaan worden.

ILDA Besturing Dit apparaat heft een D25 port zodat het via een PC gestuurd worden kan. Als een 25-pin kabel aangesloten is,

wordt de laser via PC bestuurd. Als geenkabel aangesloten is, werkt het in de laatste opgeslagen modus.


DMX Kanaaltabel DMX kanaaltabel met ILDA

KANAAL WAARDE OMSCHRIJVING






CH2 Grating Effect








224-255 Scanned Beam Effect (Pattern Effect) DMX kanaaltabel zonder ILDA

KANAAL WAARDE FUNCTIE

CH 1 MODE

000-018 Laser UIT













235-255 DMX MODE


CH 2 GROUP







CH 4 COLOR

000-007 Original

008-015 Red

016-023 Green

024-031 Yellow

032-039 Blue

040-047 Purple

048-055 Light Blue

056-063 White




208-255 Strobing

CH 5 CLIPING




CH 6 ZOOMING


128-169 Zooming IN

170-209 Zooming OUT


CH 7 ZOOM SPEED 000-255 Snel naar langzaam

CH 8 Y AXIS ROLLING




CH 9 ROLL SPEED 0-255 Snel naar langzaam















CH 14 Y AXIS MOVING




CH 15 MOVE SPEED 0-255 Snel naar langzaam

CH 16 X AXIS MOVING




CH 17 MOVE SPEED 0-255 Snel naar langzaam
















PATRONENLIJST

DMX 1 2 3 4 5

000-015

016-031

032-047

048-063

064-079

080-095

096-111

112-127

128-143

144-159

160-175

176-191

192-207

208-223

224-239

240-255

BELANGRIJK: De elektrische producten mogen niet bij het huisvuil gegooid worden. Gelieve deze te laten recycleren daar waar er centra’s hiervoor voorzien is. Raadpleeg de plaatselijke autoriteiten of uw verkoper ivm de manier van recycleren


MANUAL DE INSTRUÇÕES De modo a poder operar e usar o equipamento correctamente e com segurança, leia este manual antes de o usar. Guarde este manual para referência futura. Especificações: 1. Voltagem: AC100-240V, 50Hz/60Hz, Fusível: 2A/250V 2. Potência: 100W 3. Laser: DPSS, DPSS, verde 532nm 100mW, vermelho 600nm 500mW, azul 455nm 800mW 4. Potência de Laser: 1000mW 5. Motor: scanners de alta velocidade 20Kpps 6. Modo de controlo: Controlo de som auto/DMX/ILDA 7. Canais DMX: 19 canais 8. Dimensões: 340 x250 x 150mm 9. Peso Liquido: 4,5kg 10. Peso Bruto: 5.5Kg

Aviso

Não exponha os seus olhos à luz directa do Laser Não desligue e ligue a unidade com frequência Esta unidade é para ser usada em espaços fechados. A temperatura de funcionamento é de 18-30ºC. Não

a utilize por mais de 4 horas ou poderá encurtar a vida do equipamento. Limpe a lente externa do equipamento com um pano limpo para remover o pó e ter o máximo

desempenho. Não remova o selo de garantia. Substitua pelo fusível com amperagem correcta. Ao usar este aparelho o efeito irá mudar conforme a música. Se mudar o som e ritmo a máquina vai

mudar a direcção e velocidade. Configuração de Funções Quando a laser é ligado, o monitor LCD no painel traseiro mostra o modo stand-alone operacional ou o endereço DMX do modo DMX. É muito fácil ajustar e alterar o modo de funcionamento do laser através do painel de controlo do LCD. Após cada reinicialização e armazenamento, o novo modo de informação será mostrada no monitor LCD na próxima vez que ligar o equipamento.

Modo Opção, para escolher o modo de operação do laser Confirmação, para armazenar o actual menu para confirmar a função

UP/DOWN, para alterar o modo de operação, parâmetros ou endereço DMX

P


OPERAÇÃO

MODO LCD DISPLAY DESCRIÇÃO

MODO STAND ALONE EFEITO PRÉ-PROGRAMADO

MODE:AUTO Mixed 5 Auto Show com 5 efeitos misturados

MODE:AUTO Laser 3D Efeito Laser 3D Effect Auto Show

MODE:AUTO Scanned Beam Efeito Scanned Beam Auto Show

MODE:AUTO Laser Lumia Efeito Laser Lumia Auto Show

MODE:AUTO Burst Grating Efeito Burst Grating Auto Show

MODE:AUTO Laser Universal Efeito Laser Universal Auto Show

MODE:SOUND Mixed 5 Sound Show com 5 efeitos misturados

MODE:SOUND Laser 3D Efeito Laser 3D Sound Show

MODE:SOUND Scanned Beam Efeito Scanned Beam Sound Show

MODE:SOUND Laser Lumia Efeito Laser Lumia Sound Show

MODE:SOUND Burst Grating Efeito Burst Grating Sound Show

MODE:SOUND Laser Universal Efeito Laser Universal Sound Show

SOM MODE:SENSITIVITY ▐▐▐▐▐▐▐▐▐▐ Configura a sensibilidade de microfone

DMX MODE: sinal 001 O laser funciona em DMX MODE.

SLAVE MODE: sinal SLAVE O laser funciona em SLAVE MODE

MIRROR MODE:MIRROR SY:Y SX:Y O laser funciona em modo espelho

Atenção No modo pré-programado standalone SOUND SHOW, o feixe laser irá desligar durante 10 segundos

sem o sinal activado pelo AUDIO/MIC.


MODO DE ACTIVAÇÃO SONORA: CONFIGURAÇÃO DE SENSIBILIDADE Pressione FUNC até que mostre S 6 Pressione UP/DOWN para configurar a sensibilidade de microfone. S 0 é para sem activação sonora, de S 1 para S 9, o

nível de sensibilidade vai ficando mais sensível. Pressione ENTER para confirmar e guardar a configuração. CONTROLO DMX Pressione FUNC entrar na selecção de MODE Pressione até que o painel LCD mostre 001 Pressione ENTER para confirmar a configuração O laser funciona em modo DMX. Configure o endereço DMX através dos botões UP e DOWN OPERAÇÂO SLAVE Pressione FUNC para entrar na selecção de MODE Pressione até que o painel LCD mostre SLAVE Pressione ENTER para confirmar a configuração O laser está funcionando no modo SLAVE. Ligue o laser MASTER a vários lasers SLAVE através de um cabo DMX e os lasers SLAVE irão fazer exactamente o mesmo que o laser MASTER. Consulte abaixo para a ligação DMX. DMX512 1. Instale as unidades numa posição adequada (fixa ou anexar). 2. Use cabos de microfone XLR em rede com as unidades em conjunto através da tomada XLR na parte traseira das unidades. Para mais cabo sugerimos um terminal na última ligação. 3. Atribua um endereço DMX para cada unidade usando dipswitches; Consulte a secção "DMX Address Quick Reference Char». (Todas as unidades definidas para # 1 e # 10 vão ficar OK) 4. Ligue a alimentação de todas as unidades, as unidades começam a reconfigurar, e em seguida, a unidade começa a trabalhar. 5. Use a consola DMX para controlar as unidades.

CONFIGURAÇÃO DE PADRÃO ESPELHO INVERSO Pressione FUNC para entrar na selecção de MODE Desça até que o que a função seja mostrada no painel LCD e o laser irá mostrar o padrão do lado direito. Pressione ENTER para confirmar a configuração. Com a ajuda do botão UP, o campo de scanner na direcção x pode ser invertido, como mostra o gráfico abaixo. Com a ajuda do botão DOWN, o campo de scanner na direcção y pode ser invertido, como mostra o gráfico

abaixo.

Nota: Alem da configuração de espelho programada no LCD, o laser pode também ser configurado através do painel de controlo ILDA.

MODO DE CONTROLO ILDA Esta unidade possui uma porta ILDA DB25 que permite o controlo através de PC. Quando o cabo de 25 pinos

esta ligado, o laser será controlado por PC. Quando o cabo é desligado, o laser irá voltar ao último modo de operação.


Mapa de Canais DMX Mapa da de Canais DMX quando em ligação ILDA

CANAL VALOR DESCRIÇÃO

CH1 Rotação

000-004 Sem rotação

005-127 Rotação esquerda para a direita

128-133 Sem rotação

134-255 Rotação direita para a esquerda

CH2 Efeito rotação

000-031 Laser 3D

032-063 Efeito Scanned Beam (Efeito padrão)

064-095 Efeito Laser Lumia


128-159 Efeito Burst Grating


192-223 Efeito Laser Universal

224-255 Efeito Scanned Beam (Efeito padrão) Mapa de Canais DMX quando não está em ligação ILDA

CANAL VALOR FUNÇÃO

MODO CH 1

000-018 Laser OFF

019-036 AUT Auto Show com 5 efeitos misturados

037-054 Efeito A3D Laser 3D Auto Show

055-072 Efeito AUB Scanned Beam Auto Show

073-090 Efeito AUL Laser Lumia Auto Show

091-108 Efeito AUN Burst Grating Auto Show

109-126 Efeito AUO Laser Universal Auto Show

127-144 SOU Sound Show com 5 efeitos misturados

145-162 S3D Sound show com LASER 3D

163-180 SOB Sound show com Scanned Beam

181-198 SOL Sound show com LASER LUMIA

199-216 SON Sound show com Burst Grating

217-234 SOO Sound show com Laser Universal

235-255 Modo DMX


GRUPO CH 2

000-051 1 Grupo padrão.

052-103 2 Grupo padrão




PADRÂO CH 3 000-255 Cada 16 para 1 grupo, total de 16 padrões.

CH 4 COLOR

000-007 Original

008-015 vermelho

016-023 verde

024-031 amarelo

032-039 azul

040-047 roxo

048-055 Azul claro

056-063 branco

064-111 Rolling Color

112-159 Jumping Color

160-127 Moving Color

208-255 Strobing

CH 5 CLIPPING

000 Padrão complete com clipping

001-127 0%~99% padrão fixo cortado

128-255 Velocidade de corte

CH 6 ZOOM

000-127 100%-5% zoom de padrão fixo

128-169 Zooming IN

170-209 Zooming OUT

210-255 Zoom alternativo

CH 7 ZOOM SPEED 000-255 Rápido para lento

CH 8 ROTAÇÃO NO EIXO Y

000-127 0 -359 graus fixos no eixo Y

128-191 Rotação da direita para a esquerda

192-255 Rotação da esquerda para a direita

CH 9 ROLL SPEED 0-255 Rápido para lento

CH 10 ROTAÇÃO NO EIXO X

000-127 0 -359 graus fixos no eixo x





CH 12 ROTAÇÃO NO EIXO Z

000-127 0 -359 graus fixos no eixo z


CH 12 ROTAÇÃO NO EIXO Z

000-127 0 -359 graus fixos no eixo z



CH 13 VELOCIDADE 0-255 Rápido para lento

CH 14 MOVIMENTO NO EIXO Y

000-127 128 Posições diferentes fixas no eixo X

128-191 Movimento da direita para a esquerda

192-255 Movimento da esquerda para a direita

CH 15 VELOCIDADE MOVIMENTO

0-255 Rápido para lento

CH 16 MOVIMENTO NO EIXO X

000-127 128 Posições diferentes fixas no eixo Y

128-191 Movimento da direita para a esquerda

192-255 Movimento da esquerda para a direita

CH 17 VELOCIDADE DE

MOVIMENTO 0-255 Rápido para lento

CH18 ROTAÇÃO GRADUAL

000-004 Sem rotação gradual


128-133 Sem rotação gradual


CH19 EFEITOS DIFERENTES



064-095 Efeito Laser Lumia

096-127 Scanned Beam Effect (Efeito padrão)

128-159 Efeito Burst Grating

160-191 Scanned Beam (Efeito padrão)

192-223 Efeito Laser Universal

224-255 Scanned Beam (Efeito padrão)


LISTA DE PADRÕES

DMX 1 2 3 4 5

000-015

016-031

032-047

048-063

064-079

080-095

096-111

112-127

128-143

144-159

160-175

176-191

192-207

208-223

224-239

240-255

Produtos eléctricos não deverão ser postos em contentores de lixo caseiros. Por favor, deposite-os em contentores para reciclagem. Questione as autoridades locais ou onde adquiriu o produto sobre como deverá proceder.


Zahvaljujemo se vam za nakup tega izdelka. Prosimo, preberite navodilo za varnost in del informacij pred uporabo izdelka. Shranite ta priročnik za poznejšo uporabo. S tem laserjem lahko ustvarite popolne laserske programe in efekte, saj je opravil vrsto strogih testov strogo pred dostavo. Prosimo, preverite priloge, navedene na strani, ko se odprete škatlo. V primeru poškodb na škatli ali če so priloge izgubljene pri tarnsportu, se obrnite na prodajalca ali na naš poprodajno servisni oddelek. Tehnični podatki 1. Napajanje: AC100-240V, 50Hz/60Hz, Varovalka: 2A/250V 2. Nazivna moč: 100W 3. Laserske diode: DPSS, zelena 532nm 100mW, rdeča 650nm 300mW, modra 450nm 800mW 4. Moč laserja: 1000mW 5. Motor: 20K visoko precizni motor 6. Načini kontrole: Zvočna aktivacija/Samodejno/DMX/ ILDA 7. DMX kanali: 19 kanalov 8. Dimenzije: 340 x 250 x 150 mm 9. Neto teža: 4.5 kg 10. Bruto teža: 5.5 kg

Opozorilo Ne izpostavljajte človeško oko direktno laserskim žarkom. Ne vklapajte in izklapajte naprave pogosto. Pred uporabo te naprave se prepričajte če je napajalnik ozemljen. Ta enota je namenjena le za uporabo v zaprtih prostorih in jo ne izpostavljajte, vlagi, vodi, tresljajem. Delovna

temperatura v napravi je 18-30 ° C, ne uporablajte jo neprekinjeno več kot 4 ure, sicer boste skrajšali življenjsko dobo naprave.

Odstranite prah z leč z krpo za optimalno svetilnost. Ne odstranjujte garancijsko nalepko, sicer boste izničili garancijo. Varovalko vedno zamenjajte s točno enakim tipom varovalke, zamenjavo s čimerkoli, razen določene

varovalke lahko povzroči požar ali električni udar in poškoduje enoto in izniči garancijo proizvajalca. Nastavitev funkcij Ko je laser vklopljen, LCD monitor na zadnji plošči prikazuje trenutno delovanje v samostojnem načinu ali DMX adreso v DMX načinu. To je zelo enostavno za vzpostavitev in spremembo načina delovanja laserja preko LCD nadzorne plošče. Po vsakem resetiranju in shranjevanju, se bodo novi podatki prikazali na LCD zaslonu pri LCD pri naslednjem vklopu.

Opcije načinov, da izbere način delovanja laserja Potrditev, za shranjevanje trenutnega menija potrdite trenutno funkcijo

UP/DOWN, za spremembo načina delovanja, parametrov ali DMX adrese

SLO


DELOVANJE

NAČIN LCD ZASLON OPIS

SAMOSTOJNI NAČIN PREDPROGRAMIRANI EFEKTI

NAČIN:SAMODEJNO Mix 5 efektov Samodejni Show z Mixom 5 efektov

NAČIN: SAMODEJNO Laser 3D Laser 3D Efekt Samodejni Show

NAČIN: SAMODEJNO Scanned Beam Scanned Beam Efekt Samodejni Show

NAČIN: SAMODEJNO Laser Lumia Laser Lumia Efekt Samodejni Show

NAČIN: SAMODEJNO Burst Grating Burst Grating Efekt Samodejni Show

NAČIN: SAMODEJNO Laser Universal Laser Universal Efekt Samodejni Show

NAČIN:ZVOK Mix 5 efektov Zvočni Show z Mixom 5 efektov

NAČIN: ZVOK Laser 3D Laser 3D Efekt Zvočni Show

NAČIN: ZVOK Scanned Beam Scanned Beam Efekt Zvočni Show

NAČIN: ZVOK Laser Lumia Laser Lumia Efekt Zvočni Show

NAČIN: ZVOK Burst Grating Burst Grating Efekt Zvočni Show

NAČIN: ZVOK Laser Universal Laser Universal Efekt Zvočni Show

ZVOK NAČIN:OBČUTLJIVOST ▐▐▐▐▐▐▐▐▐▐ Nastavitev občutljivosti mikrofona

DMX NAČIN: signal 001 Laser dela v DMX NAČINU.

SLAVE NAČIN: signal SLAVE Laser dela v SLAVE NAČINU

OGLEDALA NAČIN:OGLEDALA SY:Y SX:Y Laser scanned world

Pozor: V predprogramiranem samostojnem načinu ZVOČNI SHOW, bo laserski žarek black-out v 10 sekundah

brez AUDIO/MIC aktivacijskega signala.


ZVOČNA AKTIVACIJA: Nastavitev občutljivosti Pritisnite FUNC dokler se ne prikaže S 6 Pritisnite UP/DOWN za nastavitev občutljivosti mikrofona. S 0 je brez zvočne aktivacije, za S 1 do S 9, nivo občutljivosti je

vse bolj občutljiv. Pritisnite ENTER da potrdite in shranite nastavitve. DMX Kontrola Pritisnite FUNC za vstop v MODE izbor Pritisnite dokler se na LCD ne prikaže 001 Pritisnite ENTER za potrditev nastavitve Laser deluje v DMX NAČINU. Nastavite DMX adreso preko gumbov UP in DOWN Slave Delovanje Pritisnite FUNC za vstop v MODE izbor Pritisnite dokler se na LCD ne prikaže SLAVE Pritisnite ENTER za potrditev nastavitve Laser deluje v SLAVE NAČINU. Povežite MASTER laser za več SLAVE laserjev prek kabla DMX, SLAVE laserji delajo točno isti laser show kot MASTER laser. Prosimo, preverite spodaj DMX kabla za sklicevanje. DMX512 1. Enote namestite v primernim položaju. 2. Uporabljajte standardne XLR mikrofonske kable da povežete svoje enote v verigo preko XLR konektorja na zadnji strani enote. Za daljše kabelske linije priporočamo da priključite DMX terminator v zadnjo enoto. 3. Določite DMX adreso za vsako enoto preko DIP stikal: glejte "DMX adrese hitri referenčni graf". (Vse enote nastavite na #1 in #10 na ON in bo OK) 4. Vklopite vse enote, enote se ponastavijo, potem začnejo delovati. 5. Uporabite DMX krmilnik za kontrolo enot.

NASTAVITEV OBRNJENIH LIKOV Pritisnite FUNC za vstop MODE izbiro Dokler se na LCD zaslonu ne prikaže pravi lik. Pritisnite ENTER, da potrdite nastavitev. S pomočjo gumba UP, lahko laserski motor kroži, v smeri x se obrne, kot grafika spodaj. S pomočjo gumba DOWN, lahko laserski motor kroži v y smeri se obrne, kot grafika spodaj.

Prosimo, upoštevajte: Poleg LCD programiranja ogledal obratno, lahko laserski motor kroži, kako določi ILDA nadzorna plošča.

ILDA Način Kontrole Ta enota ima vhod za ILDA DB25, ki omogoča, da se enota računalniško kontrolira. Ko je 25-pin kabel povezan,

bo laser računalniško kontroliran. Če se kabel odklopi, se laser vrne na zadnji način delovanja.


DMX Kanali DMX Kanali ko je ILDA priključena

KANAL VREDNOST OPIS






CH2 Grating Effect








224-255 Scanned Beam Effect (Pattern Effect) DMX Kanali ko ILDA ni priključena

KANAL VREDNOST FUNKCIJA

CH 1 MODE

000-018 Laser OFF













235-255 DMX MODE


CH 2 GROUP







CH 4 COLOR

000-007 Original

008-015 Red

016-023 Green

024-031 Yellow

032-039 Blue

040-047 Purple

048-055 Light Blue

056-063 White




208-255 Strobing

CH 5 CLIPING




CH 6 ZOOMING


128-169 Zooming IN

170-209 Zooming OUT



CH 8 Y AXIS ROLLING



















CH 14 Y AXIS MOVING





CH 16 X AXIS MOVING




















SEZNAM LIKOV

DMX 1 2 3 4 5

000-015

016-031

032-047

048-063

064-079

080-095

096-111

112-127

128-143

144-159

160-175

176-191

192-207

208-223

224-239

240-255

Električni izdelki ne smejo biti dana v gospodinjske odpadke. Prosimo, da jih pripeljete do reciklažnega centra. Vprašajte svoje lokalne oblasti ali svojega prodajalca o nadaljevanju.


Va multumim pentru achizitionarea acestui produs. Va rugam sa cititi manualul de utilizare inainte de utilizarea produsului. Pastrati acest manual pentru referinte viitoare. Acest produs poate crea programe si efecte laser deosebite si a trecut o serie de teste stricte inainte de livrare. Va rugam sa verificati accesoriile la deschiderea cutiei. In cazul in care cutia este deteriorata sau constatati lipsa accesoriilor in urma transportului, va rugam sa contactati distribuitorul. Specificatii tehnice 1. Tensiune de alimentare: 100-240 VAC, 50Hz/60Hz, siguranta: 2A/250V 2. Putere nominala: 100 W 3. Dioda laser: DPSS, verde 532nm 100mW, rosie 650nm 300mW, albastra 450nm 800mW 4. Putere laser: 1000mW 5. Scaner: 20K scanner de mare viteza 6. Moduri de functionare: activat de sunet/automat/DMX/ ILDA 7. Canale DMX: 19 canale 8. Dimensiuni (mm): 340 x 250 x 150 9. Greutate neta: 4.5 kg 10. Greutate bruta: 5.5 kg

Avertisment Feriti-va privirea de fasciculul laser. Nu porniti sau opriti aparatul in mod frecvent. Inainte de utilizarea aparatului asigurati-va ca sursa de alimentare are pamantare. Acest aparat este destinat numai utilizarii in interior trebuie sa fie ferit de apa si umiditate. Temperatura de

functionare a acestei unitati este de 18-30°C, nu utilizati in mod continuu mai mult de 4 ore, in caz contrar se reduce durata de functionare a aparatului.

Utilizati un servetel de hartie pentru a indepărta periodic praful depus pe lentilele externe pentru a optimiza fluxul de lumina.

Nu indepartati sau rupeti eticheta de garantie, in caz contrar acest lucru duce la pierderea garantiei. Inlocuiti intotdeauna cu acelasi tip de siguranta. Inlocuirea cu orice alt tip diferit de siguranta decat cea

specificata poate provoca incendii sau socuri electrice, deteriorarea unitatii si va anula garantia acordata produsului.

Setare functii Cand laserul este pornit, monitorul LCD de pe panoul din spate va afisa modul autonom de operare sau adresa DMX a modului DMX. Este foarte usor de configurat si de schimbat modul de functionare a laserului, prin intermediul panoului de control LCD. Dupa fiecare resetare si salvare,modul informatiilor noi va fi afisat pe monitorul LCD la urmatoarea pornire.

Optiune Mod, pentru alegerea modului de functionare a laserului Confirmare, pentru memorarea meniului curent

SUS/JOS, pentru schimbarea modului de functionare, al parametrilor sau al adresei DMX

RO

PERICOL! FASCICOL LASER! NU PRIVITI DIRECT CATRE RAZA LASER! LASER CLASA 3B


FUNCTIONARE

MOD AFISAJ LCD DESCRIERE

MOD AUTONOM EFECT PRE-PROGRAMAT

MOD:AUTO 5 efecte combinate Auto Show cu 5 efecte combinate

MOD:AUTO Laser 3D Laser 3D Effect Auto Show

MOD:AUTO Fascicul de lumina Efect fascicul de lumina Auto Show

MODE:AUTO Laser Lumia Efect Laser Lumia Auto Show

MOD:AUTO Burst Grating Efect Burst Grating Auto Show

MOD:AUTO Laser Universal Efect Laser Universal Auto Show

MOD:SUNET Mixed 5 effect Spectacol de sunet cu 5 efecte combinate

MOD:SUNET Laser 3D Spectacol de sunet Efect Laser 3D

MOD:SUNET Fascicul de lumina scanat

Spectacol de sunet efect fascicul de lumina scanat

MOD:SUNET Laser Lumia Spectacol de sunet efect Laser Lumia

MOD:SUNET Burst Grating Spectacol de sunet efect Burst Grating

MOD:SUNET Laser Universal Spectacol de sunet efect Laser Universal

SUNET MOD:SENSIBILITATE ▐▐▐▐▐▐▐▐▐▐ Setare sensibilitate microfon

DMX MOD: semnal 001

Dispozitivul laser functioneaza pe MODUL DMX.

SLAVE MOD: semnal SLAVE

Dispozitivul laser functioneaza pe MODUL SLAVE

MIRROR MOD:MIRROR SY:Y SX:Y The laser scanned world

Atentie Pe modul autonom preprogramat SOUND SHOW (SPECTACOL DE SUNET), fasciculul luminos se va

intrerupe dupa 10 secunde daca nu exista semnal AUDIO/MIC.


MOD SUNET ACTIVAT: Setare Sensibilitate Apasati tasta FUNC pana cand S 6 va fi afisat Apasati tasta UP/DOWN pentru a seta sensibilitate microfonului. S 0 indica faptul ca sunetul nu este activ. De la S 1 la S 9,

nivelul de sensibilitate creste. Apasati tasta ENTER pentru a confirma si salva setarea. Control DMX Apasati tasta FUNC pentru a accesa selectarea MODULUI. Apasati pana cand pe panoul LCD apare 001 Apasati tasta ENTER pentru a confirma setarea Dispozitivul laser functioneaza pe MODUL DMX . Setati adresa DMX cu ajutorul butoanelor UP si DOWN. Functionare Slave Apasati tasta FUNC pentru a accesa selectarea MODULUI. Apasati pana cand pe panoul LCD apare SLAVE Apasati tasta ENTER pentru a confirma setarea Laserul functioneaza pe MODUL SLAVE. Conectati laserul MASTER la mai multe lasere SLAVE prin intermediul unui cablu DMX. Laserele SLAVE vor oferi exact acelasi spectacol de lumini ca si laserul MASTER. Va rugam sa verificati mai jos pentru conexiunea prin cablu DMX. DMX512 1. Instalati aparatul intr-o pozitie convenabila. 2. Utilizati cabluri de microfon XLR standard pentru a conecta aparatele intre ele. Pentru ultimul cablu utilizati un terminator de linie. 3. Atribuiti o adresa DMX fiecarei unitati cu ajutorul comutatoarelor dip; vezi “Tabelul cu adrese DMX” (Toate unitatile setate pe #1 si #10 vor fi OK) . 4. Porniti toate aparatele. 5. Utilizati consola DMX pentru controlul instalatiei.

SETARE MODEL MIRROR REVERSE

• Apasati tasta FUNC pentru a accesa MODUL de selectare. • Apasati tasta ENTER pentru a confirma setarea. • Cu ajutorul butonului UP, laserul pe directia x ar putea fi inversat, ca si graficul de mai jos. • Cu ajutorul butonului DOWN, laserul pe directia y ar putea fi inversat, ca si graficul de mai jos.

Imaginile vor fi setate de catre panoul de control ILDA.

Mod de control ILDA Acest aparat are un port ILDA DB25 care permite unitatii sa fie controlate de catre calculator. Atunci cand un

cablu cu 25-pini este conectat la portul unitatii, laserul va fi controlat de calculator. In cazul in care cablul este deconectat, laserul va reveni la ultimul mod de operare.


Tabel canale DMX Tabel Canale DMX cand dispozitivul ILDA este conectat

CANAL VALOARE DESCRIERE

CH1 Rotatie Grilaj

000-004 Fara rotire grilaj

005-127 Rotatie grilaj in sensul acelor de ceasornic


134-255 Rotatie grilaj in sens invers acelor de ceasornic

CH2 Efect Grilaj

000-031 Laser efect 3D

032-063 Efect fascicul luminos scanat (efect tipar/model)

064-095 Efect Laser Lumia


128-159 Efect Burst Grating


192-223 Efect laser universal

224-255 Efect fascicul luminos scanat (efect tipar/model) Tabel Canale DMX cand dispozitivul ILDA NU este conectat

CANAL VALOARE FUNCTII

MOD CH 1

000-018 Laser OPRT

019-036 AUT Auto Show cu 5 efecte combinate

037-054 A3D Laser efect 3D Auto Show

055-072 AUB Efect Fascicul luminos scanat Auto Show

073-090 AUL Efect Laser Lumia Auto Show

091-108 AUN Efect Burst Grating Auto Show

109-126 AUO Efect Laser Universal Auto Show

127-144 SOU Spectacol de sunet cu 5 efecte combinate

145-162 S3D Spectacol de sunet cu LASER 3D

163-180 SOB Spectacol de sunet cu fascicul luminos scanat

181-198 SOL Spectacol de sunet cu LASER LUMIA

199-216 SON Spectacol de sunet cu Burst Grating

217-234 SOO Spectacol de sunet cu laser universal

235-255 MOD DMX


GRUP CH 2

000-051 Tipare Grupa 1





TIPAR CH 3 000-255 Fiecare 16 pentru Grupa 1, total 16 tipare.

CULOARE CH 4

000-007 Original 008-015 Rosu 016-023 Verde 024-031 Galben 032-039 Albastru 040-047 Mov 048-055 Abastru deschis 056-063 Alb 064-111 Rulare culoare 112-159 Omitere culoare 160-127 Miscare culoare 208-255 Strobing

CH 5 CLIPING

000 Tipar complet fara perforare 001-127 0%~99% tipar fix perforat 128-255 Viteza perforare

CH 6 TRANSFOCARE

000-127 100%-5% tipar fix transfocat

128-169 Marire

170-209 Micsorare

210-255 Zoom alternativ

CH 7 VITEZA ZOOM 000-255 De la rapid la lent

CH 8 ROTIRE AXA Y

000-127 Rotire axa fixa Y la 0 -359° 128-191 Rotire in sensul acelor de ceasornic 192-255 Rotire in sens invers acelor de ceasornic

CH 9 VITEZA ROTIRE 0-255 De la rapid la lent

CH 10 ROTIRE AXA X

000-127 Rotire axa fixa X la 0 -359°

128-191 Rotire in sensul acelor de ceasornic

192-255 Rotire in sens invers acelor de ceasornic



CH 12 ROTIRE AXA Z

000-127 Rotire axa fixa Z la 0 -359° 128-191 Rotire in sensul acelor de ceasornic

CH 12 ROTIRE AXA Z

000-127 Rotire axa fixa Z la 0 -359° 128-191 Rotire in sensul acelor de ceasornic 192-255 Rotire in sens invers acelor de ceasornic


CH 14 MISCARE AXA Y

000-127 128 pozitii fixe diferite pe axa X

128-191 Miscare in sensul acelor de ceasornic

192-255 Miscare in sens invers acelor de ceasornic

CH 15 VITEZA MISCARE 0-255 De la rapid la lent

CH 16 MISCARE AXA X

000-127 128 pozitii fixe diferite pe axa Y

128-191 Miscare in sensul acelor de ceasornic

192-255 Miscare in sens invers acelor de ceasornic

CH 17 VITEZA MISCARE 0-255 De la rapid la lent

CH18 Rotire grilaj


005-127 Rotire grilaj in sensul acelor de ceasornic


134-255 Rotire grilaj in sens invers acelor de ceasornic

CH19 Efect diferit

000-031 Efect Laser 3D

032-063 Efect fascicul luminos scanat (Efect tipar/model)

064-095 Efect Laser Lumia


128-159 Efect Burst Grating


192-223 Efect Laser Universal



LISTA TIPARE

DMX 1 2 3 4 5

000-015

016-031

032-047

048-063

064-079

080-095

096-111

112-127

128-143

144-159

160-175

176-191

192-207

208-223

224-239

240-255

Deseurile electrice si electronice nu trebuie anmestecate cu gunoiul menajer. Pentru dezafectarea acestora, prezentati-le la centrele de colectare special amenajate in acest scop. Interesati-va la autoritatile locale cu privire la informatii despre procedura de dezafectare selectiva a deseurilor provenind din aparatura electrica si electronica.

Imported from China by:

LOTRONIC SA Avenue Zénobe Gramme 11

B - 1480 SAINTES


Documents

©Copyright Lotronic 2014 LAS1000RGB-5IN1 1 · output power. Always set up and install all laser effects so that all laser light is at least 3 meters (9.8 feet) above the f loor