Crompton ED 3

7/25/2019 Crompton ED 3

http://slidepdf.com/reader/full/crompton-ed-3 1/7

fold

fold

fold

fold

fold

fold

1

2

3456

7

891011

12

13 14

1516

17 18

19 20 21 22

Sheet of 3

2a

2a



2324

26

27

28

25

26a

Sheet 2 of 3



29

30

31

32

33

34

35

36

37

38

39

40 41

top

top

42 43

44

Sheet 3 of 3



2

2

2

2

2.1 - Start glueing the rear face of #2 at the upper sides.Make sure the two corners are aligned.Finish one side, then the other.

The hull is in three main pieces. Start with #1 (outer-lower hull) and #2 (inner hull)

Note that tabs go on the INSIDE

Inside of rear face. Note tabs on the inside.There are two small plain pieces (#2a) to fillthe area where the air grills (#23 and #24) will go

2a

(not shown)

1 23 4

4.2 - Attach #1 to #2. Apply glue sparingly.4.2.1 - Start at the rear bottom edge4.2.2 - glue front bottom edge.4.2.3 - glue sides only where shown

4.2.1

4.2.2

4.1 - Check #1 and #2 carefully for fit. Adjust #2 as necessary.

4.2.3



5 6

7 8

1

2

6.1 - assemble engine pieces.Note that #4 is wrapped around #39, (a 4-ply blank piece) then trimmed

4

39

6

7

5

3

40

41

NOTE: do NOT assemble the entire engine yet

right engine pieces are assembled as shown.left engine is similar

43

42

7.1 - attach #43 (chain)7.2 - add #3, #4, #5, #6in that order

6

54 3

11

1210

9

8

39

8910

11

12

42

39

2324

left engine pieces

engine color in final model is alighter shade of gray

radiator grills



interior complete, ready to add outer shell

9 10

23

24

13

14

15

16

1718

21

19

22

20

25

26

attach #25 to theunderside of #26. Glue only around the4 edges.

1

2

11 - attach #26 to #1/#211.1 - apply glue only alongthe edges shown on one side11.2 - apply glue to the otherside, the same way

glue tabs on both sides

11.3 - glue #26rear side tabsto rear of #2

11.4 - glue #26rear panel to#2 rear panel

11.5 - glue #26 bottom to #1 bottomNote: glue only at the front

12.1 - glue top tabs to inside front panels

12.2 - add #26a fillers between tabs

12.3 - glue #26 outside front panels to #2 inside front panels

13 - assemble track units. arrows point toward front.

11

12 13



14 15

16 17

14.1 - Wrap outer tracks (#31, #32) around track frames (#29,#30)

14.2 - add spacers ( to track units (exact placement is not important)

3135

3629

3334

30

32

37

37

38

38

27

28

4.5-inch Howitzer:Model shown here iscomplete with wheelswhich will be omittedwhen mounted insidethe vehicle.

Whitemodel of 4.5-inch howitzer without wheels, inside the ED3.Small tabs beneath the short axle were added as adhoc supports -the model includes a long axle that does not need the tabs.

Documents

Crompton ED 3