Upload
evgeniykras-sound
View
9
Download
0
Embed Size (px)
Citation preview
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2009 American Honda Motor Co., Inc. – All Rights Re
AII 41964
REMOTE CONTROL ENGINE STARTERserved. AII 41964 (0911
2010 ACCORD CROSSTOUR
) 0
Issue Date
NOV 2009
PARTS LISTRemote Engine Starter Unit KitP/N 08E91-E22-101ATransmitter
Control unit
Antenna
Key ring
Protective tape
Caution label
Fuse label
Accessory User’s Information Manual
Quick start guide
Remote Control Engine Starter Attachment KitP/N 08E92-TA0-101Engine starter harness
Control unit bracket
Template
3 Relays
Ground bolt
Flange nut
1 of 238E92-TP6-1000-91
20 Wire ties
2 Long wire ties
8 Urethane tapes
A-Pillar clip
TOOLS AND SUPPLIES REQUIREDFlat-tip screwdriverPhillips screwdriverSmall flat-tip screwdriverRatchet10 mm Socket10 mm Combination wrenchIsopropyl alcoholShop towelTape measureClip removerScissorsSmall rubber malletHonda Diagnostic System (HDS)Masking tape2 Pairs of needle nose pliersDiagonal cuttersUtility knifePlastic Trim Tool (T/N SILTRIMTL10)
2 of 23 AII 41964
Illustration of the Remote Control Engine Starter Installed on the Vehicle
INSTALLATION
1. Make sure you have the anti-theft codes for the audio and navigation system (if equipped), then write down the radio station presets.
2. Disconnect the negative cable from the battery.
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
711102AY
40A FUSES
ENGINE STARTER HARNESS
ANTENNA
3A FUSE
CONTROL UNIT
(0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
Setting the Control Unit3. Using a small flat-tip screwdriver, adjust the switches
on the (accessory) control unit to the locations shown.
NOTE:• The switches must be adjusted before the
control unit is plugged in.• If the switch settings are not correct, the remote
engine starter will not operate correctly.• If adjusting the switches with the control unit
installed in the vehicle, touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity.
• If you change the switch settings with the unit connected, you must disconnect the unit then reconnect it before the settings change.
932501AS
CONTROL UNIT
SMALL FLAT-TIP SCREWDRIVER
Discharge any static electricity.
SET
SWITCHES
SWITCHES
SW:1 RR Junction unit --------------------> OFF
SW:2 Trunk or Tailgate --------------------> ON
SW:3 Smart Entry --------------------------- > OFF
SW:4 Horn or Buzzer Answerback ----> OFF
SW:5 Trunk Main SW----------------------- > OFF
SW:6 Reserve---------------------------------> ON
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 41964
4. Using isopropyl alcohol on a shop towel, clean the area where the protective tape will attach. Attach the protective tape to the control unit over the switches.
Removing the Vehicle Parts5. Using a plastic trim tool, disengage the eight
retaining tabs and remove the left and right lenses from the roof console.
772505AS
CONTROL UNIT
SWITCHESPROTECTIVE TAPE
BACKING
Clean with isopropyl alcohol.
931806AS
ROOF CONSOLE
LEFT LENS
4 RETAINING TABS
RIGHT LENS
4 RETAINING TABS
PLASTIC TRIM TOOL
(0911) 3 of 23
6. Open the sunglass holder. Remove the four screws (two black and two silver) and let the roof console drop down. Unplug the vehicle connectors and remove the roof console.
7. Turn the sunvisor holder 45° and remove the two sunvisor holders.
730202AB 2 BLACK SCREWS
ROOF CONSOLE
SUNGLASS HOLDER(Open.)
VEHICLE CONNECTORS
2 SILVER SCREWS
6D1806BY
SUNVISOR HOLDER
Turn.
SUNVISOR HOLDER
4 of 23 AII 41964
8. Pull away the door seal from the left A-pillar trim.
9. Using a small rubber mallet and a shop towel, gently tap the left A-pillar trim at the position shown to release the clip.
10. Pull away the remaining door seal from the left A-pillar trim, and remove the left A-pillar trim (two clips).
711110BY
CLIP
A-PILLAR TRIM
A-PILLAR
PIN
STRIKE POINTSHOP TOWEL
SMALL RUBBER MALLET
LEFT A-PILLAR TRIM
CLIP
DOOR SEAL
Strike perpendicularly to the vehicle.
TRIANGLE MARK
Pull.
6D18070Y
2 CLIPS
DOOR SEAL
LEFT A-PILLAR TRIM
(0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
11. Remove and discard the clip from the left A-pillar trim, and install a new A-pillar clip (supplied) onto the left A-pillar trim.
12. Remove the driver’s dashboard lower cover (eight clips, two hooks, and vehicle connector).
6D18080Y
CLIP (Discard.)
LEFT A-PILLAR TRIM
NEW A-PILLAR CLIP
6D1803AY
8 CLIPS
DRIVER’S DASHBOARD LOWER COVER
2 HOOKS
VEHICLE CONNECTOR
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 41964
13. Remove the driver’s dashboard under cover (three clips and one pin).
14. Raise the front side of the left front door sill trim, and remove the left front door sill trim (four clips and one retaining tab).
6D18040Y
3 CLIPS
DRIVER’S DASHBOARD UNDER COVER
PIN
932502AS
FRONT
RETAINING TAB
LEFT FRONT DOOR SILL TRIM
4 CLIPS
(0911) 5 of 23
15. Pull away the door seal, and remove the left kick panel (two clips).
16. Pull away the door seal, and remove the driver’s dashboard side lid (three clips, four tabs, and three hooks).
932503AS
2 CLIPS
DOOR SEAL
LEFT KICK PANEL
6D1805BY
DRIVER’S DASHBOARD SIDE LID
3 CLIPS
3 HOOKS
DOOR SEAL
4 TABS
6 of 23 AII 41964
17. Lower the tilt lever and pull the steering wheel out.
18. Remove the upper steering column cover:• Insert a flat-tip screwdriver along the column
guide inside the lower steering column cover, and gently pry out the retaining tab of the upper steering column cover.
• Push the lower steering column cover in at the areas shown to release the two retaining tabs, and pull up the upper steering column cover to release the two hooks and one retaining tab.
7215010K
LOWER STEERING COLUMN COVERRETAINING
TAB
TILT LEVER
COLUMN GUIDE
FLAT-TIP SCREWDRIVER
2 HOOKS
2 RETAINING TABS
Push.
RETAINING TAB
UPPER STEERING COLUMN COVER
(0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
19. Remove the lower steering column cover (three screws). The upper screws are self-tapping screws.
20. If equipped, remove the vehicle unit (two bolts and vehicle 28-pin connector).
7111090Y
LOWER STEERING COLUMN COVER
SELF-TAPPING SCREWSCREW
732903BY
BOLT
VEHICLE 28-PIN CONNECTOR
VEHICLE UNIT(If equipped)
BOLT
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 41964
21. Remove the bolt, and remove the vehicle unit from the vehicle bracket.
Routing the Engine Starter Harness22. Using isopropyl alcohol on a shop towel, clean the
areas where the fuse labels will attach.
23. Attach the two 40A fuse labels to the engine starter fuse block.
24. Attach the 3A fuse label to the engine starter relay block.
932518AS VEHICLE BRACKET
BOLT
VEHICLE UNIT
STEERING SHAFT
732821BY
ENGINE STARTER HARNESS
FUSE BLOCK(Clean with isopropyl alcohol.)
3A FUSE LABEL
40A FUSE LABELS
RELAY BLOCK(Clean with isopropyl alcohol.)
(0911) 7 of 23
25. Install the three relays to the engine starter relay blocks.
26. Route the 12-pin/8-pin/5-pin connector end of the engine starter harness over the vehicle bracket towards the center of the vehicle.
6D1802BY
ENGINE STARTER HARNESS
RELAY BLOCKS
3 RELAYS
932520AS
ENGINE STARTER HARNESS
12-PIN/8-PIN/5-PIN CONNECTOR
STEERING SHAFT VEHICLE
BRACKET
8 of 23 AII 41964
27. Route the 12-pin/8-pin/5-pin connector end of the engine starter harness to the ignition switch.
28. Unplug the vehicle 5-pin connector from the ignition switch, and plug the engine starter harness 5-pin connector into the ignition switch.
NOTICE: Check that the engine starter harness 5-pin connector is plugged to the ignition switch and it is locked securely. A loose connector can cause the engine to stall.
6D1812DY
12-PIN/8-PIN/5-PIN CONNECTOR
IGNITION SWITCH
ENGINE STARTER HARNESS
5-PIN CONNECTOR
Unlock connector Lock connector
Push.
VEHICLE 5-PIN CONNECTOR
Push.Pull.12
3 1
2
Unplug. Plug.
(0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
29. Wrap one urethane tape around the vehicle 5-pin connector, and tuck it into the area shown.
30. Unplug the vehicle 12-pin connector and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the combination light switch.
6D1813AY
URETHANE TAPE
VEHICLE 5-PIN CONNECTOR
VEHICLE 5-PIN CONNECTOR
VEHICLE BRACKETPush.
Push.
Locked connector1
2
6D18141Y
12-PIN CONNECTORS
VEHICLE 12-PIN CONNECTOR
ENGINE STARTER HARNESS
COMBINATION LIGHT SWITCH
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 41964
31. Unplug the vehicle 8-pin connector and plug it into the engine starter harness 8-pin connector. Plug the remaining engine starter harness 8-pin connector into the wiper switch.
32. Using two wire ties, secure the engine starter harness to the vehicle harness. Do not secure to the SRS harness.
6D18151Y
VEHICLE 8-PIN CONNECTOR
ENGINE STARTER HARNESS
8-PIN CONNECTORS
WIPER SWITCH
6D1816BY
VEHICLE HARNESS
ENGINE STARTER HARNESS
2 WIRE TIES
(0911) 9 of 23
33. Using two wire ties, secure the engine starter harness to the vehicle harness in the areas shown.
34. Unplug the vehicle 20-pin connector from the vehicle unit removed in step 21, and plug it into the engine starter harness 20-pin connector. Plug the remaining engine starter harness 20-pin connector into the vehicle unit.
6D1817BY
VEHICLE HARNESS
VEHICLE CLIP
ENGINE STARTER HARNESS
WIRE TIE
WIRE TIE VEHICLE HARNESS ENGINE
STARTER HARNESS
Inside.
932504AS
VEHICLE 20-PIN CONNECTOR
20-PIN CONNECTOR
VEHICLE UNIT
VEHICLE 20-PIN CONNECTOR
20-PIN CONNECTOR
ENGINE STARTER HARNESS
10 of 23 AII 41964
35. Align the green tape on the engine starter harness with the clip on the vehicle harness, and secure the engine starter harness to the vehicle harness using one wire tie.
36. Near the connector, secure the engine starter harness to the vehicle harness using one wire tie.
37. Using two long wire ties, secure the engine starter harness to the vehicle harness at the locations shown.
6D1811AY
VEHICLE HARNESS
ENGINE STARTER HARNESS
WIRE TIE
VEHICLE CLIP
GREEN TAPE
932505BS ENGINE STARTER HARNESS
VEHICLE HARNESSWIRE TIE
VEHICLE HARNESS
LONG WIRE TIE
CONNECTOR
(0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
38. Reinstall the vehicle unit to the vehicle bracket using the bolt removed in step 21.
39. Route the engine starter harness along the vehicle harness to the front of the fuse box.
40. Using one wire tie, loosely secure the engine starter harness to the vehicle harness.
932519AS
VEHICLE BRACKET
VEHICLE UNIT
BOLT(removed in step 21)
6D1820AY
WIRE TIE (Loosely secure.)FUSE BOX
ENGINE STARTER HARNESS
VEHICLE HARNESS
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 41964
41. Unplug the vehicle 5-pin connector from the fuse box. Plug the engine starter harness 5-pin connector into the fuse box 5-pin connector. Wrap one urethane tape around the vehicle 5-pin connector.
NOTICE: Check that the engine starter harness 5-pin connector is plugged to the fuse box 5-pin connector and it is locked securely. A loose connector can cause the engine to stall.
6D1823DY
FUSE BOX
VEHICLE 5-PIN CONNECTOR
5-PIN CONNECTOR
Unlock connector
VEHICLE 5-PIN CONNECTOR
Push.Pull.
Push.
ENGINE STARTER HARNESS
URETHANE TAPE
Lock connector
Push.
Lock connector
Push.
122
1
2
3 1Unplug. Plug.
(0911) 11 of 23
42. Plug the engine starter harness 12-pin connector into the fuse box 12-pin connector.
NOTE: If another accessory 12-pin connector is already plugged into the fuse box: Unplug the 12-pin connector from the fuse box, then plug the engine starter harness 12-pin connector into the fuse box. Remove and discard the dummy connector from the engine starter harness, and plug the other accessory 12-pin connector into the engine starter harness 12-pin connector.
6D1821BY
FUSE BOX 12-PIN CONNECTOR
FUSE BOX
ENGINE STARTER HARNESS 12-PIN CONNECTOR
6D1822BY
FUSE BOX 12-PIN CONNECTOR
12-PIN CONNECTOR
12-PIN CONNECTOR
DUMMY CONNECTOR(Discard.)
FUSE BOX
ANOTHER ACCESSORY 12-PIN CONNECTOR
ENGINE STARTER HARNESS
12 of 23 AII 41964
43. Using one wire tie, loosely secure the engine starter harness to the vehicle harness.
44. Unplug the vehicle 20-pin connector (blue), and plug it into the engine starter harness 20-pin connector. Plug the engine starter harness 20-pin connector (white) into the vehicle 20-pin connector.
6D1824AY
VEHICLE HARNESS
ENGINE STARTER HARNESS
WIRE TIE (Loosely secure.)
6D1825AY
FUSE BOX
VEHICLE 20-PIN CONNECTOR
20-PIN CONNECTOR (White)
ENGINE STARTER HARNESS
20-PIN CONNECTOR VEHICLE 20-PIN
CONNECTOR (Blue)
(0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
45. Attach the engine starter harness 20-pin connector to the vehicle connector as shown.
46. Remove and discard the hood opener bolt. Install the ground bolt with the engine starter harness ground terminal attached.
932506AS
HOOD OPENERVEHICLE
CONNECTOR
ENGINE STARTER HARNESS 20-PIN CONNECTOR
ENGINE STARTER HARNESS 20-PIN CONNECTOR
932507BS
BOLT (Discard.)
HOOD OPENER
VEHICLE PANEL
GROUND BOLT
ENGINE STARTER HARNESS GROUND TERMINAL
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 41964
47. Using one wire tie, secure the engine starter harness to the vehicle harness.
48. Using two wire ties, loosely secure the engine starter harness to the vehicle harness.
932508BS
WIRE TIE
ENGINE STARTER HARNESS
VEHICLE HARNESS
6D18290Y
VEHICLE HARNESS
ENGINE STARTER HARNESS
2 WIRE TIES (Loosely secure.)
VEHICLE HARNESS
(0911) 13 of 23
Installing the Antenna49. Using scissors, cut out the appropriate template.
932509BS
TEMPLATE(Cut out.)
14 of 23 AII 41964
50. Using scissors, trim the template.EX model:
EX–L model:
932510AS
TEMPLATE
Cut out.
Cut out.
932511AS
TEMPLATE
Cut out.
(0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
51. Attach the template to the windshield.EX model:
EX–L model:
932513AS
TEMPLATE
CENTER
BLACK CERAMIC
WINDSHIELDBLACK CERAMIC OF MIRROR BASE
MASKING TAPES
932514AS
TEMPLATE
CENTER WINDSHIELD
BLACK CERAMIC
MASKING TAPES
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 41964
52. Using two pair of needle nose pliers, bend the antenna plate according to the full scale drawing shown.
721509BY
ANTENNA
PLATE
10 mm(0.4 in.)
SCALE
2 PAIRS OF NEEDLE NOSE PLIERS
10 mm(0.4 in.)
(0911) 15 of 23
53. Starting near the antenna end of the cable, wrap three urethane tapes around the antenna cable at the measurements shown.
54. Cut one urethane tape in half. Wrap the two cut pieces around the antenna cable at the measurements shown.
7111110Y
390 mm(15.3 in.)
20 mm(0.8 in.)
620 mm(24.4 in.)
ANTENNA CABLE
3 URETHANE TAPES
Cut in half.
ANTENNA CABLE
URETHANE TAPE Cut pieces of urethane tape
20 mm(0.8 in.)
16 of 23 AII 41964
55. Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach.
56. Remove the backing from the antenna. Insert the antenna plate over the headliner, and attach the antenna to the windshield aligning it with the template. Press the antenna firmly.NOTE: This antenna should only be installed if the ambient air temperature is 15°C (60°F) or above.
57. Remove the template.
58. Gently pull down the headliner, and tuck the antenna cable under the headliner. Be careful not to crease the headliner.
721510AY
TEMPLATE
HEADLINER
ANTENNAPress firmly.
PLATE
BACKING
Clean with isopropyl alcohol.
932522AS
VEHICLE HARNESS
ANTENNA CABLE
HEADLINER
HEADLINER
ANTENNA CABLE
(0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
59. Using isopropyl alcohol on a shop towel, clean the areas where the urethane tapes will attach.
60. Cut one urethane tape in half. Secure the antenna cable to the vehicle panel using the cut pieces of urethane tape.
61. Route the antenna cable down and under the dashboard through the A-pillar trim opening.
932515AS
ANTENNA CABLE
VEHICLE PANEL(Clean with isopropyl alcohol.)
Cut in half.
URETHANE TAPE
VEHICLE HARNESS
932523AS
ANTENNA CABLE
A-PILLAR TRIM OPENING
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 41964
62. Using four wire ties, secure the antenna cable to the vehicle harness.
63. Using one wire tie, secure the vehicle 5-pin connector unplugged in step 41 to the vehicle harness.
64. Using two wire ties, secure the antenna cable to the vehicle harness.
6D18430Y
ANTENNA CABLE
4 WIRE TIESVEHICLE CLIP
VEHICLE HARNESS
6D1844AY
WIRE TIE
ANTENNA CABLE
WIRE TIE
VEHICLE HARNESS
VEHICLE 5-PIN CONNECTOR(unplugged in step 41)
(0911) 17 of 23
65. Route the antenna cable along the engine starter harness as shown.
66. Secure the antenna cable using the three loosely secured wire ties.
Installation of the Control Unit67. Install the control unit bracket to the control unit.
6D1845BY
ANTENNA CABLE
ENGINE STARTER HARNESS
VEHICLE HARNESS
LOOSELY SECURED WIRE TIE(Secure.)
LOOSELY SECURED WIRE TIE(Do not secure yet.)
6D18461Y
CONTROL UNIT BRACKET
CONTROL UNIT
18 of 23 AII 41964
68. Plug the engine starter harness 28-pin connector into the control unit.
69. Install the clip on the engine starter harness to the control unit bracket.
70. Plug the antenna terminal into the control unit.
6D1847BY
CONTROL UNIT BRACKETCONTROL
UNIT
CLIP
28-PIN CONNECTOR
ENGINE STARTER HARNESS
6D18480Y
ANTENNA TERMINAL
CONTROL UNIT
(0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
71. Secure the control unit to the vehicle frame using the flange nut.
72. Wrap one urethane tape around the vehicle connector.
932524AS
VEHICLE FRAME
FLANGE NUT
CONTROL UNIT
932516AS
VEHICLE CONNECTOR
URETHANE TAPE
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 41964
73. Attach the engine starter harness relay block clip to the vehicle frame.
74. Bundle up the excess antenna cable and secure it to the engine starter harness and the vehicle harness using the loosely secured wire tie.
75. Using two wire ties, secure the antenna cable to the engine starter harness.
6D1860AY
ENGINE STARTER RELAY BLOCK
ENGINE STARTER HARNESS RELAY BLOCK CLIP
VEHICLE FRAME
6D18620Y
ANTENNA CABLE(Bundle up.)
ENGINE STARTER HARNESS
VEHICLE HARNESS
2 WIRE TIES
LOOSELY SECURED WIRE TIE(Secure.)
(0911) 19 of 23
76. Under the hood, locate the area where the caution label will attach. Using isopropyl alcohol on a shop towel, clean the hood where the caution label will attach.
77. Attach the caution label to the hood in the area shown.
78. Reinstall all removed parts. Check that all clips and other fasteners are installed securely. Take care not to pinch the airbag with the clip during reinstallation of the A-pillar trim. Do not push the A-pillar trim excessively.
79. Reconnect the negative cable to the battery.80. Enter the customer’s radio anti-theft code, and reset
the radio station presets.81. Reset the clock.82. Perform “REMOTE ENGINE STARTER
REGISTRATION” and “FUNCTION CHECK.”
932517AS
HOOD(Clean with isopropyl alcohol.)
CAUTION LABEL
BACKING
20 of 23 AII 41964
REMOTE ENGINE STARTER REGISTRATION1. Acquire the PCM Code from ISIS.
2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch on.
3. Start the HDS, and click the car icon.
4. Input the VIN and other requirements in accordance with the HDS, then click the check button.
792901AH
CAR ICON
752502AS
CHECK BUTTONInput the VIN and other requirements.
(0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
5. Select “Honda Systems,” then click the check button.
6. Select “R/C ENG STARTER,” and click the check button.
752503AS
CHECK BUTTONSelect “Honda Systems.”
752504AS
CHECK BUTTONSelect “R/C ENG STARTER.”
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 41964
7. Check that “REMARKS” is shown, then click the check button.
8. Select “REGISTER REMOTE CONTROL ENGINE STARTER UNIT,” then click the check button.
752505AS
CHECK BUTTON
Check that “REMARKS” is shown.
752506AS
CHECK BUTTONSelect “REGISTER REMOTE CONTROL ENGINE STARTER UNIT.”
(0911) 21 of 23
9. Check that “Obtain PCM-code (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the password. (USA)” is shown, then click the check button.
10. Input the PCM Code, then click the check button.NOTE: To ensure security, the PCM code (password) is changed everyday, so it is impossible to register the remote controlled engine starter if the date of the PCM code acquisition and registration are different. The date of the HDS tester should also be the same.
752507AS
CHECK BUTTON
Check that “Obtain PCM-code (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the password. (USA)” is shown.
752509AS
CHECK BUTTON
Input the PCM Code.
22 of 23 AII 41964
11. Check that “The registration of the Remote Control Engine Starter Unit has been completed” is shown, then click the check button.
12. Check that “Check that the engine can be started by the Transmitter” is shown, then click the check button.
13. Perform the function test on next the page then remove the HDS.
752510AS
CHECK BUTTON
Check that “The registration of the Remote Control Engine Starter Unit has been completed” is shown.
752511AS
CHECK BUTTON
Check that “Check that the engine can be started by the Transmitter” is shown.
(0911) © 2009 American Honda Motor Co., Inc. – All Rights Reserved.
FUNCTION CHECKOperating Conditions• Hood is closed• Shift lever in park• Parking brake is on• The key is out of the ignition• All doors and tailgate closed and locked
Inspection1. Within 1 second, press the command button, and then the start button on the transmitter.
The engine should start if all operating conditions are met.Does the engine start?
2. Press the command button on the transmitter, and within 1 second, press the stop button. The engine should stop.
Does the engine stop?
Yes - Operation is normal.
No:• Make sure all “Operating Conditions” are met.• Check the engine starter harness connections.• Connect the HDS and check for an indicated failure.
(Refer to the appropriate service manual for details.)
Yes - Operation is normal.
No - Check the engine starter harness connections.
3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions:
NOTE: After each test, the ignition key must be cycled, or the driver’s door must be opened and closed.• Move the shift lever out of the P position.• Unlock or open the doors or the tailgate.• Open the hood.• Insert the key in the ignition.• Press on the brake pedal.
Does the engine stop after each of these tests?
4. Check that the power window or the moon roof does not function when the engine is started with the transmitter.5. Press the command button on the transmitter two times and check the vehicle condition on the display.6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away, and in direct sight.
Yes - Operation is normal.
No - Check the engine starter harness connections.
© 2009 American Honda Motor Co., Inc. – All Rights Reserved. AII 4196
732904AY
DISPLAY
STOP BUTTON
COMMAND BUTTON
START BUTTON
TRANSMITTER
4 (0911) 23 of 23