Embed Size (px)
Citation preview
CROWN I N G5 H I ELD NO. 3285 M I L L I N G MACH I N E
The No. 328S Crowningshield Milling Machine is well designed and economically produced by a manufacturer with over 50 years experience.
This is a 2 H.P. machine, that is ideally suited where the emphasis is on tool room applications, and heavier work.
SPECIFICATIONS
Speeds
Arbor
100-2650 RPM
9" shoulder to nut
Table area ... . ......... . . .. . . . . . . . . . . . . . . ..... 227 sq. in.
Number of T slots 3
Size of T slots
Size of spindle tops
Hole through spindle
Table Size
Longitudinal Range
With Handscrew
With Power Feed
Crossfeed
Vertical Range
% "
No. 1 0 B & S
% "
28 % " x 8 % "
1 7 % "
14"
6 ',4 "
9"
No. 328S Milling Machine includes
Class 3 Timken adjustable precision tapered roller bearings on spindle and jack shafts, V Belts, feed dials graduated in .001" table stops, crank handles, Allen wrenches, 3 step motor pulley, 2%6" polished overarm and overarm support with oil impregnated bronze bearing. Less motor and switch .......................................... $1550.00
2 H.P. Motor, 220/440V - 60 Cycle, 3 Phase, 1800 R.P.M. mounted and wired to reversing switch.
. . . . . . . . . . . . . . . ......... . . . . . . . . . . . . . . ........... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $220.00
Magnetic Starter, 3 phase, 60 Cycle, mounted and wired. . ............................................. .............................. $50.00
Optional Equipment
No. 328PF Power Feed Attachment with a 1.4 H.P. independent motor drive and reversing switch - 14" Travel and with an infinite speed range from .72" per minute to 2.875" per minute. This unit operates through the lead screw, therefore, must be installed at the factory. ...................................................................... $395.00
l;4. HP vertical head attachment bored for 2%6" over-arm ..... .. .......... . . . . ............ _ .... .... ................................. . . $295.00
ACCESSORIES
Complete Oil Cutting Facilities, including builtin tank 1l0V-300 GPH Pump, flexible hose and fittings. . ....................................................................... $ 99.50
No. 328 Arbor, 1" Dia. No. 10 B & S. Taper 9" from shoulder to nut. .............................................. 62.50 Draw-in Rod for Arbor ............................................ 7.50
\ Extra Large Pulley and matching V Belt for spindle speeds of 100 RPM with 1800 RPM Motor .......................................................................... 25.00
W:c����e7/���d'
a:jt�w1:c���� .. ���: .. ��_�����.�= . . ��.� 15.00
Draw-in Attachment complete with draw bar, adapter and 1 round 1h " std. 2AB Collet .......... _ 75.00
Extra Collet for draw-in attachment, ;16" to %6" Dia. by ;16ths ............................................ Each 8.80-
No. 4 Swivel vise with hardened and ground steel jaws. Complete with wrench ........................ 60.00
Extra Collets for Vertical Head, ;16" to % " by 1h6ths .................................................................. Each 10.45
7" Rotary Table calibrated in 4-90° arcs .. . . . . . . . . . . 170.00
6" Dividing Head and tail stock with 2 indexing plates .......................................................................... 250.00 Draw-in bar for Dividing Head ............................ 18.50
Extra Collets for Dividing Head 1A6 to � by 16ths. Each ................................................................ 13.20
Cutter assortment covering all basic milling operations . .. _ . . ....................... . ...... . . . ...... ... . . ... ... . . . . . . ... 125.00
100 Brodhead-Garrett pays shipping charges on all orders over $25.00.
CROWN I NGSHI ELD N O. 3 MILLING MACH I N E
The No. 3 Milling Machine offers student instruction :n all basic milling machine procedures at a price to fit 3ll school budgets.
The Crowningshield Milling Machine is one of the !!lost versatile machines on the market today. It can be :lSed to demonstrate the type of production milling students will face after graduation. With proper accessories you can perform tool room milling applications and all round vertical milling operations.
GENERAL SPECIFICATIONS
Spindle Size of taper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . No. lOB&S Hole through spindle . . . . . . . . . . . . . . . . . . . . . . . .845B&S Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 through 2625 Longitudinal Power Feed Speeds . . 3 Table Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171.5 sq. in. Number of T-slots . . . . . . . . . . . . . . . . . . . . . . . 1 Width of T-slots . . . . . . . . . . . . . . . . . . . . . �8" R.P.M. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1800 Shipping Wt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 850 Lbs. Overarm Diameter . . . . . . . . . . . . 2-%6" Table Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24;2" x 7/1 Longitudinal Travel . . . . . . . . . . . . . . . . . . . . : . . . Cross Feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vertical Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The No. 3 Milling Machine Includes
14�2" 3 �2"
9"
Class 3 Timken adjustable precision tapered roller bearings on spindle and jack shafts, Vee Belts, feed dials graduated in .001" table stops, crank handles, Allen wrenches, 3 step motor pulley, 2-%6" polished overarm' and overarm support with oil impregnated bronze bearing. Without motor and switch ........ $995.00
Optional Equipment
No. 3 LS Longitudinal Lea� Screw Attachment, hand wheel with dial graduated in .001 ". May be attached or removed by operator in 5 minutes. Lever feed may not be used while Lead Screw Attachment is in place. Must be installed at fa<;tory ....... ..................................... $125.00
1 H.P. Motor 220 Volt, 60 Cycle, 3 Phase, 1750 R.P.M. mounted and wired to reversing switch .... $128.50
Magnetic Starter, � Phase, 60 Cycle, mounted and wired . .. . . . . ..................... . . . . . . . _ . . . . . . . . . . . . . . . . . . . . ... . . . . . . . . . . . .. . . . $ 50.00
No. 3PF Rack and Pinion Gear type power feed (operates independent of the lead screw. ) ........ $162.50
1,4 H.P. Vertical Head Attachment bored for 2-%6" overarm ...... .... . . . . . . . . ... . . . . . . _ . . .. .... . ... . . . . . . ...... . . . . . . . : ......... $295.00
Additional Accessories
Complete Oil Cutting Facilities, including built in tank, 110 Volt, 300 GPH Pump, flexible hose and fit-tings ............................................................................ $ 99.50
No. 3 Arbor, 1" Diameter No. 10 B&S Taper 5 % " shoulder to nut .......................................................... $ 35.00
Draw-in Rod for Arbor ............................................ 7.50
Extra Large Pulley and matching V-Belt for spindle speeds of 100 R.P.M. with 1800 R.P.M. Motor .... $ 25.00
Machine Lamp with flexible arm, non-glare reflector, 7' cord and switch ............................ ... ......................... $ 15.00
Draw-in Attachment complete with draw bar, adapter ....................................................... _ . . . . . . . . . . . . . . . . . . . . . . . . ..... . . $ 75.00
Extra Collets for draw-in attachment lh6 to %6" Dia. by lh6ths .................................................................. $8.80 Ea.
No. 4 Swivel vise with hardened and ground steel jaws. Complete with wrench-opens 2%. by 4 % by 1 %. ....... . ................ . . . .. . . .. . . . . . . . . . . . ...................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 60.00
Extra Collets for Vertical Head lh6 to %th by lh6ths ....... -. ........................................................... : ........... $ 10.45 Ea.
7" Rotary Table calibrated in 4-90° arcs ........ $170.00
6" Dividing Head and tail stock with 2 indexillg plates .......................................................................... $250.00
Draw-in bar for Dividing Head ............................ $ 18.50
Extra Collets for Dividing Head lh6 to %. by 16ths . .. .................................................... _ ......................... $13.20 Ea.
An assortment of cutters to perform most tool room cutting operations (28 cutters) ............................ $125.00
Brodhead-Garrett pays shipping charges on all orders over $25.00. 101
