STRTES 4 LroCS2000 Cable StripperOperating Instructions

SET-LP:- CS2000

The Model CS2000 requires partial assembly upon receipt.The following items will be included:-

Main Stripping UnitHandle Assembly (inc large washer & nut)Stripping Length Stop Assembly (inc rod and strip lengthstop with screw)Perspex Guard

.Blade Opening Lever2 Allen KeysI Set ofStripping Blades ofyour choice

First assemble the handle to the main unit. To do this, tumthe unit on its side. and screw the handle into the large threadedhole in the control block (drawg nos 43), making sure the nut andrvasher are fitted on first. Screw the handle until at least l5mm (thefurther the better) of the thread is engaged. Tighten the large locknut securely against the control block to hold the handle in place.

Set the unit on the bench with the handle to the right. Installthe strip length rod into the threaded hole on the left front oftheunit. Tighten the rod using the locknut making sure the flat alongthe length ofthe rod is in a vertical position. Slide the strip lengthstop onto the rod to the desired position and tighten using thervrench provided.

Install the Blade Opening Handle (Drawg nos 34) into theleft or right hand blade carrier using the smallest allen wrench.

Next install the blades. To do this remove the socket headscrews from the two blade carriers, using the wrench provided.Slide one blade into each carrier, with the countersink on the dieblades facing the cable grippers. Check that each blade is fullyseated on the bottom ofits blade carrier. Re-install the blade holderscrews but leave loose. Pull the handle back slightly until the bladesclose. Adjust the blades for the desired spacing. Die blades shouldcome together for the best stripping performance, but may beseparated to allow for variations in cable sizes. Centre the openingofthe die blades directly above the cable height adjuster (drawg nos30) Ifusing straight blades, centre the opening using the cableheight adjuster as a guide.

After all adjustments have been made, tighten the bladecarrier screws securely. Return the handle to its starting position,and note that the blades now open automatically at the end of eachstripping cycle. The blade opening lever is not required when theunit is used in the automatic mode, and it may be removed form theblade carriers using the smallest allen wrench. Ifdesired for precisestripping or operator preference, the unit may be set to a manualmode so that the blades remain permanently closed and are openedby the operator via the use of the blade opening lever.

To set the unit in the manual mode, tip it on its side, andrefering to the the exploded parts diagram, remove the plates andscrews shown as in numbers 65,38 and 39 on the drawing. The unitwill now function with the blades permanently closed, and theblades are now opened manually using the blade opening lever. Thelever may be mounted on either blade carrier and the angle adjustedfor operator comfort.

Bolt the unit securely to the bench with the handle to theright. Install the perspex guard by removing the two front and twomiddle screws on the sides of the slide plate. The guard should bepositioned with the angle over the blades. Re-install the screws andtighten. Place the two adjusting wrenches in the correspondin-e holesin the right front of the unit for convenience.

OPERATION: - CS2000Insert the wire or cable to be stripped, between the clamps

and blades up to the strip length stop. Ifthe unit is being used in theautomatic mode, the cable height adjuster may be used to helpcentre the wire or cable properly on the blades. Use the smallestallen wrench and insert it under each blade to loosen the two grubscrews holding the cable height adjuster (Drawg nos 30). Pull up onthe adjuster to the desired height and re-tighten the screws. Iftheunit is being used in the manual mode, the use of the cable heightadjuster is not necessary. Centre the wire or cables directly in theblades.

To strip, pull the handle back all the way and return it to thestart position. (Sometimes the faster the pull the cleaner the strip)If the desired strip length is longer than what can be achieved withone pull, simply cycle again until the slug is removed. NOTE: Theability to use multiple cycling to remove the slug is dependent onthe cable construction and strip length.

MAINTENA|ICE:- CS2000The CS2000 should be cleaned or dusted off DAILY to preventchalk build up, apart from that periodically and lightly lubricate allmoving parts with machine oil or a light grease. No other mainte-nance should be required.

TROIIBLE SHOOTING:- CS2000

PROBLEM: Wire/Cable does not sfrip.SOLUTIONS:l. Check that the blades are the correct size and type for the wire/

cable.2. Check that the blades are properly installed, see earlier.3. Check that the blade carrier screws are securely tightened.

PROBLEM: Handle becomes loose.SOLUTION:l. Securely tighten lock nut against control block.

PROBLEM: Strip length stop will not slide on rod.SOLUTION:l. Check rod for burrs, remove & clean if necessary.

PROBLEM: Cable Grippers leaye marks on cable.SOLUTION:l. Try shrinking down on grippers some heatshrink or fabric

emery cloth etc.

o7-2930.3 1 .32.33.34.36.37.38.39.40.41 .42.43.44.45.46.47.48.49,50.5 1 .52.53.54.55.56.62.63.64.65.oo.67 ,68.69.70.7 1 .72.73.74.75 .76.78.79.80.8 1 .82.83.84.85.86.E7,

UK7007/29 Blades (not shown)UK7030 - Cable Height AdjusterUK7031 -Cam BarUK7032 - Slide Plate ClampUK7033 - Shoulder BoltUK7034 - Blade Opening HandleUK7036 - Spring PostUK7037 - Cable GripperUK7038 - PlateUK7039 - BlockUK7040 - Drive PinUK7041 - GearUK7042 - Slide PlateUK7043 - Control BlockUK7044 - Main CastingUK7045 - Blade CarrierUK7046 - PostUK7047 - Spring PostZSSB1240 - Shoulder BoltUK7049 - HandleUK7050 - Roller CamUK705l - Length Stop Rod (N/S)UK7052 - Perspex Guard (N/S)UK7053 - Length Stop (N/S)ZSH0612 - Length Stop Lock Bolt (N/S)ZNF06 - Length Stop Locknut (N/S)

EXPLODBD VIEW OF PARTS FOR THB CS2OOO CABLE STRIPPER

SERIES 4 LTD, TOTTON, HANTS, SO40 3WXTcl:- (02380) 866377

WBC06 - Lenglh Stop Lock Bolt Cover (N/S)UK7062 - Post A!)UK7063 - Clamp Spring LeftUK7064 - Clamp Spring RightZSH0425 - ScrewZSPP0410 - ScrewZDU1 - BushZCET'I -CirclioUK7069 - NutZSG0304 - Grub ScrewZNF10 - NutZWFI0 - WasherZSPP0410 - ScrewZNF04 - NutZWF04 - WasherZRP01 . PinWSPEXOl - SpringWSPEXO2-SpringUK7080 - Handle GripZWF16 - WasherWAKSSO - Large Adjusting Wrench (N/S)WAKS15 - SmallAdjusting Wrench (N/S)ZSH0616 - Blade Clamp ScrewUK7085 - Serial Nos LabelUK7086 - Cable Gripper L. Hand SN 1 15+UK7087 - Cable Gripper R. Hand SN 115+(N/s)= -NotShown

-@

IFA l l-H,

l - z

['ax:- (02380) 866323

GS2000 Final Packins & Gheck List

1 x Ma in Body . . . r r . . . r . r , ! r r r r r r r . r

Check Paintwork...Check 2 x Blade holder screws in place... .Check 2 x Length height adj screwsCheck 2 x Blade opening grub screwsCheck Hole has been tapped for length stop

1x Length Stop rod f i t ted wi th M6 Nut . r r . . . . . r r r . ! ! . . r r ,

1 x Lgngth Stop with M6 thumb Scrgw.r . r . r . , , r . r , r . r . r . . . . .Note :- Check slide fit of this itemwith Length Stop Rod

1 x Pull handle with handle gripfitted with M16 washer & Nut in place

1xBladeOpeningHandlg . r r r . . . r . r r . . . r . . . . r r , . . t . r r r r r

I x A l lgn Key for b ladg scrgws . . , r r r r . . ! ! ! . . . . r r r r . . . . r r . . . . , .

1 x Opp Instructions & 12 Month Guarantee .