2012 NEW TOOLS

2460 DIE-CAST CAP-TYPE OIL FILTER WRENCH - 64MM X 14TOYOTA / LEXUS / SCION

Single-piece, die-cast aluminum design will withstand the high-est torque loads when removing aluminum Oil Filter HousingCaps found on many late model Toyota, Lexus and Scion vehi-cles. ½” sq. drive.

2481 HEAVY-DUTY CAP-TYPE OIL FILTER WRENCH - 76MM X 14FORD / MAZDA / MERCEDES

Built with higher torque specs to service stubborn Oil Filters & Housings Caps. Features extra-thick wall construction with 3/8” square & 7/8” hex drive.

2490 FUEL FILTER TOOL - FORD 7.3L Removes and installs Diesel Fuel Caps on ’95 – ’02 Ford 7.3L.Also works on other Diesel Filter systemsusing same design. Features combination 3/8” square and 7/8” hex drive.

2087 OIL DRAIN TOOL – VW / AUDIPrevents oil spillage during filter change. Screws into filterhousing to open one-way valve and drains oil. Features 20”(51cm) hose with plastic plug. Fits many VW & Audi vehiclesfrom ‘05 – ‘09.

DIFFERENTIAL PLUG EXTRACTORSFor removal of female style plugs with rounded off inserts.

No. Application 9035 5/16” plugs w/ 1/4” square hole 9037 1/2” plugs w/ 3/8” square hole9038 3/4” plugs w/ 1/2” square hole

7420 FORD TRANS FILLER ADAPTERTool is necessary to fill or add fluid to the 5R55W automatictransmission on ’03 & up Ford Explorers. For use with SuctionGun after removing fill plug.

7070 COOLING SYSTEM PRESSURETESTER KIT

Pinpoints external leaks caused by loose clamps or leakyhoses, connectors, water pumps or radiators. Diagnoses inter-nal leaks caused by a blown head gasket or damaged block orhead. Tests pressure on radiator and coolant bottle caps. Kitincludes hand pressure pump, 4 cooling system adapters & 2dual-function cap adapters. Services most US & Asian & someEuropean models..

66

2874 CAM CHAIN TENSIONER RETAINER – VW / AUDI

Holds the chain and tensioner in position during assembly and disassembly on many VW & Audi vehicles.

2865 TWIN CAMSHAFT HOLDER –VW / AUDI

Special bar locks camshafts relative to each other during timingbelt and tensioner service or when removing crank bolts. Use with CTA #2872 TDC Lock Pin Tool. Applications: VW/Audi V6 w/ 2 valves per cylinder.

2867 TWIN CAMSHAFT HOLDER –VW / AUDI

Special bar locks camshafts relative to each other during timingbelt and tensioner service or when removing crank bolts. Use with CTA #2872 TDCLock Pin Tool. Applications: VW/Audi V6 2.7L & 2.8L w/ 5 valves per cylinder.

2869 TWIN CAMSHAFT HOLDER –VW / AUDI

Special bar locks camshafts relative to each other during timingbelt and tensioner service or when removing crank bolts. Use with CTA #2872 TDC Lock Pin Tool. Applications: VW/Audi V8 w/ 5 valves per cylinder

2872 TDC LOCK PIN TOOL – VW / AUDIFor use with #2865, 2867 & 2869 Camshaft Holders to lock the crankshaft at TDC.

2870 CAM ADJUSTMENT GAUGE KIT -AUDI

Locks and holds camshafts when adjusting the left and rightcamshafts. Services Audi A4, A6, A8 2000 – 2007 w/ AVK engine.

2012 NEW TOOLS

67

2715 TENSION PULLEY SPANNER - MITSUBISHI / HYUNDAI / CHRYSLER

Adjusts timing belts having idler pulleys with pin holes. Pins in offset head of tool engage the pulley to rotate around the retaining bolt.

2062 OXYGEN SENSOR SOCKET –NARROW SLOT

22mm (7/8”) hex socket with narrow slot for strength.Combination 3/8” square drive and 1” hex drive. Nickel plated.

2047 IPR SOCKETServices the Injector Pressure Regulator (IPR) on Ford Diesels.Use with 3/8” drive tools.

8100 CRANKSHAFT BOLT REMOVERGenerates up to 600 ft. lbs. of force to service Timing Belts,Crankshaft Seals, Harmonic Balancers and Bell Housings.Saves time when working on vehicles with limited Crankshaft bolt access. Tool is bi-directional to both loosen and tighten bolts. Use with impact sockets. OAL: 24”/61cm

3355 FUEL INJECTION TEST KIT –UPDATE SET

Upgrades CTA #3300 kit to cover virtually any application.Includes the following packed in blow-mold case:Hyundai, Kia, Mitsubishi Style11mm Fuel Rail Adapter15mm Fuel Rail Adapter16mm Fuel Rail AdapterHair Pin Adapters1/4” (6mm) Honda/Ford5/16” (8mm) Toyota Prius 90ºSchrader Type Adapters.308 x 32 – 90º Ford/BMW 7/16 x 20 – 90º GM/Chrysler8mm Volvo

2012 NEW TOOLS

2367 FORD TRITON SPARK PLUG REPAIR KIT – 1.9, 3.8, 4.6, 5.4 & 6.8L(’96 – ’03)

Over-sized, alloy steel inserts provide new threads on blownspark plugs. Repairs other brand inserts that fail. (Supersedes CTA #98140)

2366 REPLACEMENT INSERT – 14MMFor use with #2367

2368 FORD TRITON 3-VALVE INSERTINSTALLATION KIT

Repairs damaged threads or blowouts. Services 5.4L & 6.8Lengines built before 10/9/07 and 4.6L engines built before11/30/07 found in many ’04 – ’08 Ford, Lincoln & Mercury vehicles.

2385 FORD TRITON SPARK PLUG SOCKET –9/16”

Removes and installs plugs found on Ford F-150 w/ Triton Engine.Features rubber insert to prevent breakage and extension w/3/8” square drive.

2112 VALVE SPRING COMPRESSOR KITReplaces valves springs and valve stem oil seals without theneed to remove the cylinder head. Applications include BMW,VW, Audi, Hyundai, Toyota, Ford, Renault, Opel, Seat and Clio.

3032 12V / 42V HYBRID CAR CIRCUIT TESTER

Tests 12 & 42V systems. Checks high volt diesel injector circuitsfound on Ford 6.0L, 6.4L and others. Safe for low current circuitsas tester only draws 3 milliamps at 12V. Automatic volt identifi-cation: Blue for 12V, Red for 42V. Features 2 bright LEDs, crystal clear handle for 360º visibility, 3 meter (10’) heavy-duty cable with hooded alligator clip andhigh-impact body with spring-strain relief.

3064 RELAY PLIERS – STRAIGHT JAWSFor safe installation and removal of relays. Nylon handles arespring loaded. Special-design jaws come in two angles, straightand 60º. Services Ford, Mazda, Chrysler, VW, Mercedes, Opel, Renault and Nissan.

3066 RELAY PLIERS – 60º JAWSFor safe installation and removal of relays. Nylon handles arespring loaded. Special-design jawscome in two angles, straight and 60º. Services Ford, Mazda, Chrysler,VW, Mercedes, Opel, Renault and Nissan.

4330 HUB REMOVAL TOOLThread onto the hub retention stud and strike tool to removehub from the back. Services Ford Super Duty and Dodge Ram2500. Features knurled handle and replaceable brass cap.

4008 STEERING KNUCKLE SPREADEREnables the removal and fitting of shock absorbers withoutdamaging the aluminum or cast iron knuckle. Tool adjusts forcentered or non-centered slot. Made of chrome-moly steel.Applications include Audi, BMW, VW, Ford, Seat, Renault,Peugeot and many Japanese vehicles.

68

©2012 CTA MANUFACTURING CORPORATION263 Veterans Boulevard, Carlstadt, NJ 07072Phone: (201) 896-1000 • Fax: 201-896-1378E-mail: info@ctatools.com • www.ctatools.com Catalog No. 0112

69

2012 NEW TOOLS

9258 HEAD BOLT REMOVER – FORD 6.0L Use with 3/4” drive tools to transmit high torque needed toloosen and tighten head bolts. Allows access to rear head boltsby eliminating the need to remove the cab from the chassis, pre-vents damage to rear heat shield and eliminates the need to remove the evaporator housing.

IN-LINE FLARING TOOL KITSAligns the adapters, cone & tube to make perfect flares. Low-profile allows use on the vehicle. Less risk of breakingadapters. Offers same results as hydraulic or vise-type tools ata fraction of the cost.No. Description 9212 SAE - 3/16”, 1/4”, 5/16” 9214 Metric - 4.75mm, 5mm, 6mm

8099 PUSH PULLERFor use with CTA and other brands of Bearing Splitters whenremoving and installing Gears, Bearings, Shafts, Pulleys andother press-fit parts.Capacity: 10 TonsSpread: 2-1/8" - 7-1/4"Screw Size: 3/4" - 16 x 12" Reach: 8-1/4"

8092 SLIDE HAMMER PULLERRemove bearings, gears, bushings, seals, etc. Features 5 lb.hammer and 3-Jaw assembly.

9990 FLOW-THRU PARTS BRUSH W/ TUBEFor parts washing sinks with circulating solvent systems. Features Trialoy ® double-duty filaments, heavy-duty grooved handleand 28” / 71cm long tube.

9992 PARTS WASH BRUSHFor hand use in a parts washing sink or solvent container.Features Trialoy® double-duty filaments and heavy-duty grooved handle. OAL: 9-1/2” (25cm)

9650 8 PC. EXTERNAL TORX® PLUS SOCKET SET New design services elliptical-shaped fasteners now found onmany vehicle applications. Standard Torx® or Ribe designs willnot fit these fasteners. Black finish and impact quality. Also available individually.No. Size Dr. No. Size Dr.9651 EP6 1/4” 9655 EP12 3/8”9652 EP7 1/4” 9656 EP14 3/8”9653 EP8 1/4” 9657 EP16 3/8”9654 EP10 3/8” 9658 EP18 1/2”

9350 5 PC. LONG SHAFT XZN TRIPLESQUARE BIT SOCKET SET

Highest quality, 2-pc. construction with extra-long shaft. Packedon socket rail. Also available individually.No. Size OAL Sq. Dr.9351 8mm 3-1/2” / 89mm 3/8”9352 10mm 4-1/8” / 105mm 1/2”9353 12mm 4-5/8” / 117mm 1/2”9354 14mm 4-7/8” / 124mm 1/2”9355 16mm 4-7/8” / 124mm 1/2”

8755 4 PC. CLUTCH-HEAD BITSOCKET SET

For servicing special fasteners found on older GM vehicles. 4 sizes to fit most applications. Sizes: 5/32”, 3/16”, 1/4”, 5/16”, all with 3/8” square drive.

TAP HOLDERSFor use with CTA Thread Reconditioning Taps. Holds tap forproper alignment in any direction and frees hand. 3/8” squaredrive and black finish.No. Description9660 Small - use with #18111, 18112, 18113, 181159665 Large - use with #18114, 18116

THREAD RE-CONDITIONING TAPSAlloy steel taps clean common oil pan threads. Also for TransferCase & Transmission Drain Plugs.No. Size Applications18111 12mm x 1.25 Infiniti, Lexus, Nissan, Toyota18112 12mm x 1.75 Ford, GM, GMC, Saturn18113 1/2” – 20 Dodge, Ford, GM, GMC, Jeep, Mitsubishi18114 14mm x 1.50 Ford, Honda, Hyundai, Kia, Mazda18115 12mm x 1.50 BMW, Mercedes Benz18116 14mm x 1.25 Jeep, Ford Truck18117 16mm x 1.50 Dodge, Jaguar18118 18mm x 1.50 Dodge Truck, Toyota, Volvo18119 22mm x 1.50 Dodge Truck, BMWNote: Use above #’s for clam-shell pack. For polybag pack, order with “B” suffix, i.e. 18111B