www.dtco.vdo.com
CTCII Compact Test Computer IIOperating Instructions
CTCIIOperating Instructions Imprint
CTC
II E
ditio
n 05
/201
1
The information contained in this documentation is subject to change without prior notice. In doing so, Continental Automotive GmbH do not enter into any obligation. The description is based on the information available at the time this documentation was printed. We reserve the right to change technical details in the descriptions, information and illustrations in this manual.
Continental Automotive GmbH shall accept no liability for incorrect information in the documentation or for any consequential damages arising from this.
CTCII, DTCO 1381, MTCO 1324, MTCO 1390, KTCO 1318, FTCO 1319, KITAS, KIPAS and Roller Interface Module are trademarks of the Continental Corporation. EFAS is a trademark of EFKON. SE2400, SE5000 and SE8400 are trademarks of Stonerigde Electronics. SmarTach is a trademark of ACTIA. The above mentioned trademarks are used to some extent in following document without special reference to their owners.
by Continental Automotive GmbH. All rights reserved.
Responsible for the content
Continental Automotive GmbHP.O. Box 16 4078006 Villingen-SchwenningenGermanyInternet www.dtco.vdo.comE-mail [email protected]
VDO A trademark of the Continental Corporation
A2C59512809 Continental Automotive GmbH 2
CTCIIOperating Instructions Preface
CTC
II E
ditio
n 05
/201
1
Dear User,
The Compact Test Computer CTCII is a compact, versatile and easy to use Service Diagnostic System by Continental Automotive GmbH.
Purpose of this document
These Operating Instructions describe the correct handling and use of the CTCII when commissioning, programming and checking the following tachographs:
Analogue tachographs
Modular tachograph MTCO 1324
Compact tachograph KTCO 1318**
Flat tachograph FTCO 1319**
Tachograph TCO 1314**
SE2400* (Stoneridge Electronics)
SE8400** (Stoneridge Electronics)
Digital tachographs
Digital tachograph DTCO 1381
EFAS (EFKON)
SE5000 (Stoneridge Electronics)
SmarTach (ACTIA)
* Firmware version 024.02 and higher** Only in conjunction with a CTCII 1318/1314, 1319
inspection licence.
A2C59512809 Continental Automotive GmbH 3
CTCIIOperating Instructions Table of Contents
CTC
II E
ditio
n 05
/201
1
Table of Contents
Chapter 1 For your safety........................................................................... 71.1 Personnel/ technical requirements ...................................................................71.2 General safety instructions ...............................................................................81.3 Conventions......................................................................................................91.4 Notes on operation ...........................................................................................91.5 Important notes on rolling road test stands ....................................................10
1.5.1 Danger when using rolling road test stands .............................................101.5.2 Notes on rolling road test stand operation ...............................................111.5.3 Safety notes on various vehicle types......................................................121.5.4 Guidelines for front-wheel drive vehicles .................................................13
1.6 Installation instructions ...................................................................................131.7 Preserving the test stand's value....................................................................14
Chapter 2 General description................................................................. 152.1 Performance characteristics of the CTCII.......................................................152.2 Product description.........................................................................................162.3 Available products and accessories ...............................................................17
2.3.1 Available products....................................................................................172.3.2 Accessories..............................................................................................17
2.4 Functional elements .......................................................................................182.5 Operating and display elements .....................................................................19
2.5.1 Key panel .................................................................................................192.5.2 Display and menu guidance.....................................................................202.5.3 Reset function .........................................................................................21
2.6 CTCII power supply ........................................................................................212.6.1 Roller Interface Module ............................................................................222.6.2 Battery operation......................................................................................232.6.3 Charging the battery.................................................................................242.6.4 Operation via the vehicle power supply ...................................................25
2.7 Connecting the CTCII to a tachograph ...........................................................262.8 Program overview (menu tree) .......................................................................27
Chapter 3 Settings .................................................................................... 31
Chapter 4 Entering a PIN for the workshop card ................................... 364.1 PIN via PIN DIRECT.......................................................................................364.2 PIN via USER SELECTION............................................................................37
4.2.1 Creating and deleting users .....................................................................384.2.2 Calling up a saved PIN.............................................................................39
A2C59512809 Continental Automotive GmbH 4
CTCIIOperating Instructions Table of Contents
CTC
II E
ditio
n 05
/201
1
Chapter 5 Preparing for measuring......................................................... 405.1 Automatic correction value .............................................................................415.2 Notes on correction value determination ........................................................425.3 Parameter sets for DTCO 1381 Rel. 1.4 ........................................................43
Chapter 6 TCO calibration........................................................................ 46
Chapter 7 Measurement and test procedures ........................................ 507.1 Road measurement ........................................................................................517.2 Rolling road test stand....................................................................................537.3 Measurement and test procedures SmarTach ..........................................56
7.3.1 General notes...........................................................................................567.3.2 SmarTach calibration ............................................................................57
Chapter 8 Device testing .......................................................................... 588.1 Speed test (analogue tachographs) ...............................................................608.2 Variable speed................................................................................................628.3 Odometer test.................................................................................................648.4 Creating a test chart (analogue tachographs) ................................................658.5 Clock test........................................................................................................67
Chapter 9 Activating KITAS ..................................................................... 68
Chapter 10 Tachograph programming.................................................... 6910.1 Programming ................................................................................................7010.2 Installation data ............................................................................................7110.3 TCO parameters...........................................................................................7210.4 Date and Time ..............................................................................................77
10.4.1 Time zones EU member states...........................................................7810.4.2 Start and end of daylight saving.............................................................7910.4.3 Programming CTCII ...............................................................................8010.4.4 Programming TCO.................................................................................81
10.5 Displaying manufacturing data .....................................................................8110.6 Distance driven.............................................................................................8210.7 Error memory...........................................................................
