CV/SVA-SERIES MODELS 900, 1000, 1300, 1400, …service.multiquip.com/pdfs/CV-SVA-SERIES-rev-0-manual.pdfCV/SVA-SERIES VIBRATOR HEADS — OPERATION AND PARTS MANUAL — REV. #0 (03/22/10)

OPERATION AND PARTS MANUAL

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

To find the latest revision of thispublication, visit our website at:

www.multiquip.com

CV/SVA-SERIESMODELS

900, 1000, 1300,1400, 1700, 2100, 2600

VIBRATOR HEADS

Revision #0 (03/22/10)

PN: 36858

PAGE 2 — CV/SVA-SERIES VIBRATOR HEADS — OPERATION AND PARTS MANUAL — REV. #0 (03/22/10)

Engine exhaust and some ofits constituents, and some dust created

of California to cause cancer, birthdefects and other reproductive harm.

by power sanding, sawing, grinding,drillingandotherconstructionactivitiescontains chemicals known to the State

Some examples of these chemicals are:

Leadfromlead-basedpaints.Crystallinesilicafrombricks.Cementandothermasonryproducts.Arsenicandchromiumfromchemicallytreatedlumber.

Your risk from these exposures varies,dependingonhowoftenyoudothistypeof work. To reduce your exposure tothese chemicals: work in aALWAYSwell ventilated area, and work withapproved safety equipment, such asdust masks that are specially designedto filter out microscopic particles.

PROPOSITION 65 WARNING

CV/SVA-SERIES VIBRATOR HEADS — OPERATION AND PARTS MANUAL — REV. #0 (03/22/10) — PAGE 3

Grinding/cutting/drilling of masonry, concrete, metal andother materials with silica in their composition may giveoff dust or mists containing crystalline silica. Silica is abasic component of sand, quartz, brick clay, granite andnumerous other minerals and rocks. Repeated and/orsubstantial inhalation of airborne crystalline silica cancause serious or fatal respiratory diseases, includingsilicosis. In addition, California and some otherauthorities have listed respirable crystalline silica as asubstance known to cause cancer. When cutting suchmaterials, always follow the respiratory precautionsmentioned above.

WARNING

Grinding/cutting/drilling of masonry, concrete, metal andother materials can generate dust, mists and fumescontaining chemicals known to cause serious or fatalinjury or illness, such as respiratory disease, cancer,birth defects or other reproductive harm. If you areunfamiliar with the risks associated with the particularprocess and/or material being cut or the composition ofthe tool being used, review the material safety datasheet and/or consult your employer, the materialmanufacturer/supplier, governmental agencies such asOSHA and NIOSH and other sources on hazardousmaterials. California and some other authorities, forinstance, have published lists of substances known tocause cancer, reproductive toxicity, or other harmfuleffects.

Control dust, mist and fumes at the source wherepossible. In this regard use good work practices andfollow the recommendations of the manufacturers orsuppliers, OSHA/NIOSH, and occupational and tradeassociations. Water should be used for dustsuppression when wet cutting is feasible. When thehazards from inhalation of dust, mists and fumes cannotbe eliminated, the operator and any bystanders shouldalways wear a respirator approved by NIOSH/MSHA forthe materials being used.

WARNING

SILICOSIS WARNING RESPIRATORY HAZARDS

SILICOSIS/RESPIRATORY WARNINGS


TABLE OF CONTENTS

Specifications and part numbers are subjectto change without notice.

CV/SVA-Series Vibrator HeadsProposition 65 Warning ........................................... 2Silicosis/Respiratory Warnings ................................ 3Table Of Contents ................................................... 4Parts Ordering Procedures ..................................... 5Safety Message Alert Symbols ............................... 6Rules For Safe Operation ....................................... 7Preparation and Operation ..................................... 8Maintenance ...................................................... 9-10Specifications ........................................................ 11Seal Installation ..................................................... 12Vibrator Head Assy. .......................................... 14-17

Terms And Conditions Of Sale .............................. 18


PARTS ORDERING PROCEDURES

ww

w.m

ultiq

uip

.com

Ordering parts has never been easier! Choose from three easy options:

WE ACCEPT ALL MAJOR CREDIT CARDS!

When ordering parts, please supply: Dealer Account Number Dealer Name and Address Shipping Address (if different than billing address) Return Fax Number Applicable Model Number Quantity, Part Number and Description of Each Part

Specify Preferred Method of Shipment:UPS/Fed Ex DHL

Priority One Truck Ground

Next Day Second/Third Day

If you have an MQ Account, to obtain a Username and Password, E-mail us at: [email protected].

To obtain an MQ Account, contact your District Sales Manager for more information.

Order via Internet (Dealers Only):Order parts on-line using Multiquip’s SmartEquip website! View Parts Diagrams Order Parts Print Specification Information

Note: Discounts Are Subject To Change

Goto www.multiquip.com and click on Order Parts to log in and save!

Use the internet and qualify for a 5% Discount on Standard orders for all orders which include complete part numbers.*

Order via Fax (Dealers Only):All customers are welcome to order parts via Fax.Domestic (US) Customers dial: 1-800-6-PARTS-7 (800-672-7877)

Fax your order in and qualify for a 2% Discount on Standard orders for all orders which include complete part numbers.*

Order via Phone: Domestic (US) Dealers Call: 1-800-427-1244

Best Deal!

International Customers should contact their local Multiquip Representatives for Parts Ordering information.

Non-Dealer Customers: Contact your local Multiquip Dealer for parts or call 800-427-1244 for help in locating a dealer near you.

Note: Discounts Are Subject To Change

Effective: January 1st, 2006

NOTICE

All orders are treated as Standard Orders and will ship the same day if received prior to 3PM PST.


SAFETY MESSAGE ALERT SYMBOLS

Safety precautions should be followed at all times when operatingthis equipment. Failure to read and understand the SafetyMessages and Operating Instructions could result in injury toyourself and others.

FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

This Owner's Manual has been developed to providecomplete instructions for the safe and efficient operationof the MULTIQUIP VIBRATOR HEADS.

Before using this equipment, ensure that theoperating individual has read and understands allinstructions in this manual.

NOTE

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform youabout potential hazards that could injure you or others. TheSafety Messages specifically address the level of exposure tothe operator, and are preceded by one of three words: DANGER,WARNING, or CAUTION.

DANGER: You WILL be KILLED orSERIOUSLY injured if you DO NOT followdirections.

WARNING: You CAN be KILLED orSERIOUSLY injured if you DO NOT followdirections.

CAUTION: You CAN be injured if youDO NOT follow directions.

Potential hazards associated with Multiquip VIBRATOR HEADSoperation will be referenced with "Hazard Symbols" whichappear throughout this manual, and will be referenced inconjunction with Safety "Message Alert Symbols".

Accidental Starting

ALWAYS place the motor ON/OFF switchin the OFF position, when the VibratorMotor is not in use.

ALWAYS wear approved eye and hearingprotection.

Sight and Hearing hazard

HAZARD SYMBOLS

Engine exhaust gases contain poisonouscarbon monoxide. This gas is colorless andodorless, and can cause death if inhaled.NEVER operate this equipment in a confinedarea or enclosed structure that does notprovide ample free flow air.

Gasoline is extremely flammable, and itsvapors can cause an explosion if ignited. DONOT start the engine near spilled fuel orcombustible fluids. DO NOT fill the fuel tankwhile the engine is running or hot. DO NOToverfill tank, since spilled fuel could ignite if itcomes into contact with hot engine parts orsparks from the ignition system. Store fuel inapproved containers, in well-ventilated areasand away from sparks and flames. NEVERuse fuel as a cleaning agent.

Burn Hazards

Rotating Parts

NEVER operate equipment with covers, orguards removed. Keep fingers, hands, hair andclothing away from all moving parts to preventinjury.

Explosive Fuel

High Temperatures – Unplug the machine andallow to cool before performing service andmaintenance functions. Contact with hot!components can cause serious burns.


■ ALWAYS use proper lifting techniques whenusing the the vibrator motor, flexible shaftand vibrator head assembly.

■ ALWAYS check to make sure that the operating area is clearbefore starting the vibrator motor or engine.

■ NEVER leave the machine unattended while running.

■ Keep the vibrator motor or engine in proper running condition.

■ Make sure that there is no buildup of concrete, grease, oil ordebris on the equipment.

■ Fix damage to the equipment immediately and always replacebroken parts.

■ This equipment should not be operated by persons under18 years of age.

■ ALWAYS check the equipment for loosened threads or boltsbefore starting.

■ NEVER use accessories or attachments, which are notrecommended by Multiquip for this equipment. Damage tothe equipment and/or injury to user may result.

WARNING:Failure to follow instructions in this manual maylead to serious injury or even death! Thisequipment is to be operated by trained andqualified personnel only! This equipment isfor industrial use only.

The following safety guidelines should always be used whenoperating this equipment.

SAFETY

■ DO NOT operate or service this equipmentbefore reading this entire manual.

RULES FOR SAFE OPERATION

■ NEVER operate this equipment without properprotective clothing, shatterproof glasses, steel-toed boots and other protective devices requiredby the job.

■ NEVER operate this equipment when not feelingwell due to fatigue, illness or taking medicine.

■ NEVER operate this equipment under theinfluence or drugs or alcohol.

EMERGENCIES

■ ALWAYS know the location ofthe nearest fire extinguisher.

■ ALWAYS know the location of thenearest and first aid kit.

■ In emergencys always know the location of thenearest phone or keep a phone on the job site.Also know the phone numbers of the nearestambulance, doctor and fire department. Thisinformation will be invaluable in the case of anemergency.


6. Immerse the head for 5 to 10 seconds, (until air stops rising),and then withdraw it slowly to let the concrete fill the voidleft by the head. The head should be completely below thesurface when vibrating to keep the head cool. Whenvibrating a thin horizontal slab, the head can be used in ahorizontal position.

Figure 2. Compaction Coveragewith 50% Radial Overlap

PREPARATION & OPERATION

This safety alert symbol is used to attract yourattention. Personal safety is involved. Whenyou see this symbol, become alert; heed itsmessage.

1. The vibrator motor, flexible shafting, and heads are shippedfrom the factory ready to use.

2. Use only the combination of flexible shafting and headsshown below in Table 1.

3. To connect the flexible shafting to the vibrator motor see(Figure 1). (382V Shafting shown)

Figure 1. Shafting to Motor Connection(382V Shafting Shown)

WARNING!WARNING!WARNING!WARNING!WARNING!MAKE CERTAIN the motor is disconnectedfrom the power source and the switch is in the"OFF" position.

4. When connecting the head to the casing, clean the matingthreads with an anaerobic sealant primer and allow it to airdry for several minutes. Apply a ring of anaerobic sealant(Loctite 271, Hernon 427 or equivalent), to the casingthreads and screw the head tightly to the casing. Wait forone hour before using.

CAUTION!CAUTION!CAUTION!CAUTION!CAUTION!If the shaft begins to helix (buckle) excessivelyduring operation, stop and investigate. This isan indication of an overload condition.

CAUTION!CAUTION!CAUTION!CAUTION!CAUTION!The vibrator head is cooled by the concrete.Operation of the vibrator head in air longerthan 2 minutes at a time will cause overheatingof the bearings which will result in prematurehead failure.

WARNING!WARNING!WARNING!WARNING!WARNING!DO NOT attempt to operate this vibrator headuntil the Safety and Operating Instructions forthe Electric Motor or Gasoline Power Unit andFlexible Shaft have been read and fullyunderstood. Failure to do so could result inserious bodily injury and/or property damage.

seziStfahS.1elbaT

LEDOM TFAHS EZISDAEH TFAHS.XAMHTGNEL

PH11ID,1-VS

RE57V413

00900010031

.TF12

PH22ID,2-VS

RE031V283

00410071 .TF82

0012 .TF12

PH33ID,3-VS

RE002V283

0041007100120062

.TF53

5. See Compaction Coverage Chart, (Figure 2).

egarevoCnoitcapmoC.2elbaT

daeH 009 0001 0031 0041 0071 0012 0062

noisnemiD-P "4 "2/1-5 "8 "8 "21 "41 "81


MAINTENANCE

Figure 3. Head Parts

MAINTENANCE

The vibrator heads should be inspected and lubricated afterevery 100 hours of use. Refer to (Figure 3).

CAUTION!CAUTION!CAUTION!CAUTION!CAUTION!DO NOT allow the vibrator head to wear belowthe following dimensions: See GeneralSpecifications - page11.

To Disassemble a Vibrator Head:1. Remove the flexible shaft from the head. Heat should be

applied to the threads to break down the anaerobic sealant.This will help prevent possible damage to the threads.Threads are left-hand.

2. Remove the casing adapter from the housing. Head shouldbe applied to the threads to break down the anaerobicsealant. Threads are right-hand. (Ref. 9)

3. Remove the hardened tip from the housing. Heat shouldbe applied to the threads to break down the anaerobicsealant. Threads are right-hand. (Ref. 1,12)

Reference

Number Description1 ....................... Housing

2 ....................... Nut or Screw

3 ....................... Bearing

4 ....................... Spindle

5 ....................... Seal

6 ....................... Spacer

8 ....................... Fitting Adapter

9 ....................... Casing Adapter

10 ..................... Shim

11 ..................... Flat Washer

12 ..................... Tip


MAINTENANCE

Assemble the Head to the Casing:

11. Clean the casing threads and the mating threads on thehead with an anaerobic sealant primer and allow to dry.

12. Apply a ring of anaerobic high strength sealand to the casingthreads. Screw the casing into the head and tighten.

13. Allow to set one hour before use.

To Reassemble a Vibrator Head:

1. Bearing Installation: Bearing installation should takeplace under the cleanest possible conditions. Inspect thespindle bearing seat diameter for nicks and burrs. If anyare found, carefully remove using a stone or fine file. Wipethe bearing seat diameter with head oil to help preventgalling while the bearing is being pressed on. Whileinstalling the bearing, the installation force should alwaysbe applied squarely and evenly to the inner race of thebearing. (Ref. 3)

2. Seal Installation: Remove any nicks or burrs that willinterfere with the installation of the seal. Make sure theseal is facing the right direction and that it is properlypositioned so that it will seat squarely without damage.See illustration on page 12. Use an installation tool thatwill apply the force evenly around the outer edge of theseal.

3. Insert the spindle with upper bearings assembled on it,into the housing. Using a light push fit, seat the bearingsinto the housing. (Ref. 4)

4. Insert the seals into the casing adapter per the sealinstallation instructions. (See page 12)

5. Clean the casing adapter external threads and the matinginternal threads on the housing with anaerobic primer andlet dry. (Ref. 1,9)

CAUTION!CAUTION!CAUTION!CAUTION!CAUTION!DO NOT use more than the specified amountof lubricant in the vibrator head. Over-fillingwill cause the head to overheat and lead topremature failure.

8. Assemble the lower bearings to the spindle. (Ref. 3)

9. Clean the tip threads and the mating threads on the housingwith anaerobic sealant primer. Allow to dry. (Ref. 1,12)

10. Apply a high strength anaerobic sealant to the tip threadsand screw the tip into the housing. Threads are right-hand.(Ref. 1,12)

4. Remove the cap screw or hex nut that holds the lowerbearings in place. (Ref. 2)

5. Remove the spindle with the upper bearings still attached.The lower bearings (tip-end) can now be removed fromthe housing.(Ref. 4)

6. Remove and discard the oil seals. Note the way the sealsface so that the new seals will be installed correctly. (Ref. 5)

7. Thoroughly clean all parts with a degreasing solvent andblow dry with air. Compressed air is not recommended forcleaning and drying solvents out of the bearings. Bearingsshould never be spun at high speed using compressed air.(Ref. 3)

8. After cleaning, inspect all parts for wear. The bearingsshould be checked by applying a light thrust load againstone bearing ring, while slowly rotating the other ring. Dothis in both directions. If any roughness or excessivelooseness is felt, the bearing should be replaced. Anyother parts that show heavy wear should also be replacedat this time. (Ref. 3)

6. Apply a high strength anaerobic sealant to the externalthreads of the casing adapter. Screw the adapter into thehousing and tighten. Threads are left-hand. (Ref. 1,9)

7. Tip head over and pour in the required amount of Lube P/N 12000-301. Refer to General Specifications Table onpage 11.


SPECIFICATIONS

SPECIFICATIONS

SNOITACIFICEPSLARENEG.3ELBAT

ledoM 009 0001 0031 0041 0071 0012 0062

thgieW .bl1.zo11

.bl2.zo6

.sbl4.zo11

.sbl4.zo01

.sbl6.zo4

.sbl8.zo11

.sbl21.zo01

htgneL "51 "41 "51 "51 "41 "31 "31

retemaiDgnirutcafunaM 8/7 61/1-1 8/3-1 8/3-1 61/11-1 8/1-2 8/5-2

retemaiDraeWmuminiM 61/31 1 4/1-1 4/1-1 61/9-1 8/7-1 4/1-2

yticapaCebuLdaeH .zo2/1 .zo2/1 .zo2/1 .zo2/1 .zo4/3 .zo1 .zo2/1-1


SEAL INSTALLATION

SEAL INSTALLATION

Figure 4. Seal Installation

HEAD ENDSHAFT END

1. Seal lip to face vibrator shaft end.2. Seal lip to face vibrator head end.

Improper seal installation may causepremature head failure.

CAUTION!CAUTION!CAUTION!CAUTION!CAUTION!

■ Seal outer case to face outer case of first seal pressed intocasing adapter.

■ Depending on vibrator head model, casing adapter may notappear exactly as shown.


NOTES


VIBRATOR HEAD ASSY.

VIBRATOR HEAD ASSY.


VIBRATOR HEAD ASSY.

.ONMETI .ONTRAP NOITPIRCSED 009 0001 0031 0041 0071 0012 0062

- 505-20371 009LEDOM X

- 105-96361 0001LEDOM X

- 105-71361 0031LEDOM X

- 105-61361 0041LEDOM X

- 505-99651 0071LEDOM X

- 105-10361 0012LEDOM X

- 105-47261 0062LEDOM X

1 200-30371 GNISUOH 1

1 100-17361 GNISUOH 1

1 100-02361 GNISUOH 1 1

1 100-00751 GNISUOH 1

1 100-50361 GNISUOH 1

1 100-97261 GNISUOH 1

2 400-33280 02-4/1OCPIRGTUN 1

2 500-33280 81-61/5OCPIRGTUN 1

2 600-79280 42-8/3OCPIRGTUN 1 1

2 500-11560 8/5x42-8/3SCHH 1 1

2 600-31560 4/3x02-2/1SCHH 1

3 200-98190 GNIRAEB 4

3 104-39001 GNIRAEB 4

3 400-39391 GNIRAEB 4 4

3 300-39391 GNIRAEB 4

3 100-39391 GNIRAEB 4

3 200-39391 GNIRAEB 4

4 200-99111 ELDNIPS 1

4 100-48491 ELDNIPS 1

4 100-17881 ELDNIPS 1 1

4 100-00962 ELDNIPS 1

4 100-58781 ELDNIPS 1

4 100-90881 ELDNIPS 1

VIBRATOR HEAD ASSY.


VIBRATOR HEAD ASSY.

VIBRATOR HEAD ASSY.


VIBRATOR HEAD ASSY.

.ONMETI .ONTRAP NOITPIRCSED 009 0001 0031 0041 0071 0012 0062

5 650-10070 LAES 2

5 120-10070 LAES 2

5 920-10070 LAES 2 2

5 640-10070 LAES 2

5 750-10070 LAES 2

5 910-10070 LAES 2

6 100-55062 RECAPS 1

8 100-05062 RETPADAGNITTIF 1




9 100-94062 RETPADAGNISAC 1







01 520-60911 MIHS 2 2

01 210-60911 MIHS 2 2

01 510-60911 MIHS 2 2

01 020-60911 MIHS 2

11 600-03070 8/3REHSAWTALF 1 1

11 800-03070 2/1REHSAWTALF 1

21 100-40211 PIT 1

21 100-86361 PIT 1

21 100-81361 PIT 1 1

21 100-50751 PIT 1

21 100-20361 PIT 1

21 100-77261 PIT 1

VIBRATOR HEAD ASSY.


Effective: July 1, 2000 TERMS AND CONDITIONS OF SALE

PAYMENT TERMSTerms of payment for parts are net 30 days.

FREIGHT POLICYAll parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin. Multiquip’s responsibility ceases when a signed manifest has been obtained from the carrier, and any claim for shortage or damage must be settled between the consignee and the carrier.

MINIMUM ORDERThe minimum charge for orders from Multiquip is $15.00 net. Customers will be asked for instructions regarding handling of orders not meeting this requirement.

RETURNED GOODS POLICYReturn shipments will be accepted and credit will be allowed, subject to the following provisions:

A Returned Material Authorization 1. must be approved by Multiquip prior to shipment.

To obtain a Return Material Authorization, 2. a list must be provided to Multiquip Parts Sales that defines item numbers, quantities, and descriptions of the items to be returned.

The parts numbers and descriptions a. must match the current parts price list.

The list must be typed or computer b. generated.

The list must state the reason(s) c. for the return.

The list must reference the sales d. order (s) or invoice (s) under which the items were originally purchased.

The list must include the name e. and phone number of the person requesting the RMA.

A copy of the Return Material Authorization 3. must accompany the return shipment.

Freight is at the sender’s expense. All 4. parts must be returned freight prepaid to Multiquip’s designated receiving point.

Parts must be in new and resalable 5. condition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked.

The following items are not returnable:6.

Obsolete parts. (If an item is in the a. price book and shows as being replaced by another item, it is obsolete.)

Any parts with a limited shelf life b. (such as gaskets, seals, “O” rings, and other rubber parts) that were purchased more than six months prior to the return date.

Any line item with an extended c. dealer net price of less than $5.00.

Special order items.d.

Electrical components.e.

Paint, chemicals, and lubricants.f.

Decals and paper products.g.

Items purchased in kits.h.

The sender will be notified of any material 7. received that is not acceptable.

Such material will be held for five 8. working days from notification, pending instructions. If a reply is not received within five days, the material will be returned to the sender at his expense.

Credit on returned parts will be issued 9. at dealer net price at time of the original purchase, less a 15% restocking charge.

In cases where an item is accepted, for 10. which the original purchase document can not be determined, the price will be based on the list price that was effective twelve months prior to the RMA date.

Credit issued will be applied to future 11. purchases only.

PRICING AND REBATESPrices are subject to change without prior notice. Price changes are effective on a specific date and all orders received on or after that date will be billed at the revised price. Rebates for price declines and added charges for price increases will not be made for stock on hand at the time of any price change.

Multiquip reserves the right to quote and sell direct to Government agencies, and toOriginal Equipment Manufacturer accounts who use our products as integral parts of their own products.

SPECIAL EXPEDITING SERVICEA $35.00 surcharge will be added to the invoice for special handling including busshipments, insured parcel post or in cases where Multiquip must personally deliver the parts to the carrier.

LIMITATIONS OF SELLER’S LIABILITYMultiquip shall not be liable hereunder fordamages in excess of the purchase price of the item with respect to which damages are claimed, and in no event shall Multiquip be liable for loss of profit or good will or for any other special, consequential or incidental damages.

LIMITATION OF WARRANTIESNo warranties, express or implied, are made in connection with the sale of parts or trade accessories nor as to any engine not manufactured by Multiquip. Such warranties made in connection with the sale of new, complete units are made exclusively by a statement of warranty packaged with such units, and Multiquip neither assumes nor authorizes any person to assume for it any other obligation or liability whatever in connection with the sale of its products. Apart from such written statement of warranty, there are no warranties, express, implied or statutory, which extend beyond the description of the products on the face hereof.

Effective: February 22, 2006


NOTES

OPERATION AND PARTS MANUAL

Your Local Dealer is:

HERE’S HOW TO GET HELPPLEASE HAVE THE MODEL AND SERIAL

NUMBER ON-HAND WHEN CALLING

© COPYRIGHT 2010, MULTIQUIP INC.

Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.

This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.

The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained inthis manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any obligations.

UNITED STATESMultiquip Corporate Office MQ Parts Department

18910 Wilmington Ave.Carson, CA 90746 Contact: [email protected]

Tel. (800) 421-1244Fax (800) 537-3927

800-427-1244310-537-3700

Fax: 800-672-7877Fax: 310-637-3284

Mayco Parts Warranty Department

800-306-2926310-537-3700

Fax: 800-672-7877Fax: 310-637-3284

800-421-1244, Ext. 279310-537-3700, Ext. 279

Fax: 310-537-1173

Service Department Technical Assistance

800-421-1244310-537-3700

Fax: 310-537-4259 800-478-1244 Fax: 310-631-5032

MEXICO UNITED KINGDOM

MQ Cipsa Multiquip (UK) Limited Head Office

Carr. Fed. Mexico-Puebla KM 126.5Momoxpan, Cholula, Puebla 72760 MexicoContact: [email protected]

Tel: (52) 222-225-9900Fax: (52) 222-285-0420

Unit 2, Northpoint Industrial Estate, Global Lane,Dukinfield, Cheshire SK16 4UJContact: [email protected]

Tel: 0161 339 2223 Fax: 0161 339 3226

CANADA

Multiquip

4110 Industriel Boul.Laval, Quebec, Canada H7L 6V3Contact: [email protected]

Tel: (450) 625-2244Tel: (877) 963-4411 Fax: (450) 625-8664

Documents

CV/SVA-SERIES MODELS 900, 1000, 1300, 1400, …service.multiquip.com/pdfs/CV-SVA-SERIES-rev-0-manual.pdfCV/SVA-SERIES VIBRATOR HEADS — OPERATION AND PARTS MANUAL — REV. #0 (03/22/10)