Cw 2015 Build Info

8/9/2019 Cw 2015 Build Info

1/13

1 | P a g e

Resolved CPRs

CAMWorks 2015SP0.1

* Please refer to Whats New PDF document for details regarding enhancements in CAMWorks 2015.

Sr.No.

CPRNumber

Help DeskID

Area Description

1.CW-49400

CW-48814

11-3494

11-3237License

The CAMWorks License Manager would stop working on a client

machine whenever the user clicked on Ok after providing the server

name and port details.

2. CW-48719 11-3191 UI

In the Italian version of CAMWorks 2015 Beta version, in the UI

displayed for interactively inserting a Multi Surface Feature, the icons

for the Face Select Option are overlapping and the selection menu is

unstable.

3. CW-48714 11-3184 System

While installing CAMWorks 2015 SP0, user encounters an error

message which states that the supported version of SOLIDWORKS or

CAMWorks Solids was not found installed. This error message is

displayed despite supported version of SOLIDWORKS and CAMWorksSolids having been installed. The installation however gets completed

successfully.

4. CW-48698 11-3145 License

The license borrowed on the client machine for one or more modules

of CAMWorks fails to initialize when it is disconnected from the

network. Instead, CAMWorks starts in Demonstration mode.

5. CW-48628 11-3107 System

If user installs CAMWorks 2015 SP0 on a system with SOLIDWORKS

2015 on which no CAMWorks version was previously installed, then

CAMWorks fails to generate toolpaths for any part.

6. CW-48615 11-3085 TechDB

In Mill machines with rotary axis, the mode for rotary axis should be

set to 'Fixed' for all features except wrapped features. Currently this is

being controlled by the settings made in TechDB and the user cannot

change them in CAMWorks.

7. CW-48582 ---- Toolpath

For the specific part, toolpaths were generated successfully in

CAMWorks 2014 version. In the CAMWorks2015 Beta version, the

application crashes when user tries to generate the same toolpaths.

8. CW-48248 11-2906 Operation

In CAMWorks 2014 SP 2.3 and CAMWorks 2015 SP0, when user tries to

save the operation plan of Face Feature for the specific part, it causes

SOLIDWORKS to crash.

9. CW-47475 11-2472 Support

Users are unable to utilize the Help option to check for Service Pack

updates. When they click on the Check button, they receive the errormessage that they are unable to connect to the Service Pack Server -

even though there is an internet connection.


2/13

2 | P a g e

CAMWorks 2015SP0

Sr.

No.

CPR

NumberCAMWorks

2015 VersionHelp

Desk IDArea Description

1. CW-47786 SP0 11-2638 Post

For a turn operation, if the user inserts a new feed rate byediting the tool path, then upon posting the newly added

feed rate is not reflected in the posted output. This was

working correctly in CAMWorks 2013.

2. CW-47748 SP0 ---- UI

In the Japanese language version of CAMWorks, for

Threading operations in Turn mode, the order of the two

options displayed in the Program point dropdown list in

Thread tab is reverse to the order displayed in the English

version of CAMWorks.

3. CW-47650 SP0 11-2423 PostThe post variable TOOL_PROTRUSION posts values only

for Mill operations but not for Turn operations.

4. CW-47617 SP0 11-2545 Rebuild

In CAMWorks 2014, the yellow exclamation mark displayed

on the feature which is not in sync with the SOLIDWORKS

part is not removed even after the user manually doing a

full rebuild and the feature is also not updated as per the

SOLIDWORKS part. This behavior is seen with MS Hole

features.

5. CW-47534 SP0 11-2477 Rebuild

For the specific Wire EDM part for which features and

operations have been generated, if the dimension of one

of the sketches is updated and Full Rebuild subsequently

done, the yellow exclamation mark is still visible over the

feature icons indicating that the feature is out of sync with

the part model.

6. CW-47518 SP0Beta2015-

USFeatures

While interactively inserting an open profile feature, the

direction of cut specified by the user is not assigned to the

feature for the first time. The user will have to edit the

feature again and reassign the direction of cut. Only then

the user assigned direction of cut is applied to the feature.

7. CW-47511 SP0 11-2354 Post

For the specific Mill-Turn part, the posted NC code for the

Pattern type toolpaths of Wrapped Open Profile feature

outputs wrong Angular values between instances.

8. CW-47471 PR2 11-2470 API

When executing the API macro

"Post_Setup_Name_Full_Name.swp", if a post operation isthe first operation in the mill part setup then, upon

executing the command 'setup.PostProcess', the output

file generated is empty.

9. CW-47391 SP0Beta2015-

USToolpath

For a VoluMill Roughing toolpath, if an Avoid area is

defined using a sketch then, is not considered for

avoidance in the generated toolpath.


3/13

3 | P a g e

Sr.

No.

CPR

NumberCAMWorks

2015 VersionHelp


10. CW-47384 PR2Beta2015-

USUI

For a turn part, when the stock type is changed to bar

stock from the SOLIDWORKS part type, then the stock

display is reset to wireframe in the display area. Also, if the

stock type is again reset to SOLIDWORKS part and the

current part is selected for stock, the available

configuration list becomes empty.

11. CW-47382 SP0Beta2015-

USUI

For defining the X Axis machining direction, an entity can

be selected. However, after closing the dialog box and

reopening, the entity that was selected does not get

highlighted in the graphics area. Due to this, user cannot

recognize which entity he has selected earlier.

12. CW-47325 PR2 11-2430 Post

For Turn operations, the Post variable

TOOL_CORNER_RADIUS is getting populated with Turn Drill

and Center Drill Diameter values.

13. CW-47278 SP0Beta2015-

EMEAAPI

Add new APIs which would let the user know, if a

CAMWorks feature has failed during the rebuild routine

and whether tool paths can be generated for the

operations in CAMWorks operation tree.

14.CW-47197

CW-45025SP0 11-1346 Setup Sheets

The parameter of "Define Coolant by Tool" is not present

in the Access based Setup Sheet or XML based Setup

Sheet.

15. CW-47187 PR2 11-2343 Help

In the Help documentation for TechDB, there is no

documentation provided on how to delete Tool Cribs

within the TechDB.

16. CW-47051 PR1 11-2308 Toolpath

For the specific Turn part with OD feature, the Roughing

Toolpath gouges the stock when Final Cut Amount is set as

0mm.

17. CW-47020 SP0 11-2282 Simulation

Contour Milling Toolpaths with helical moves are not being

simulated correctly in CAMWorks 2014 version. It worked

correctly in CAMWorks 2012 version.

18. CW-47016 PR211-2273

11-2420Features

If a part created in CAMWorks 2013 containing multiple

circular pockets with tapers is opened in CAMWorks 2014,

the user is prompted for rebuild. Even after selecting

"Light" rebuild, the earlier defined circular pockets get

deleted. Also, the user will not be able to define the same

features again by choosing multiple in 2.5 axis feature

wizard.

19. CW-46979 SP0 11-2248 Toolpath

For the specific Turn part, the ID Bore Rough toolpath

gouges the part when it is generated using the Variable

Allowanceoption enabled (with Radial and Axial

allowance having different values). Toolpath is correct if

Radial and Axial allowance values are equal.


4/13

4 | P a g e

Sr.

No.

CPR

NumberCAMWorks

2015 VersionHelp


20. CW-46942 PR2 11-2233 Features

In CAMWorks 2014 SP2, the Face feature recognized using

Automatic Feature Recognition (AFR) in Turn module

includes the undercut features available on the part, which

is incorrect. This was working correctly in CAMWorks 2012.

21. CW-46887 SP0 11-2194 SupportThe email address given on the Enhancement Request

Form needs to be corrected to [email protected].

22. CW-46886 SP0Beta2015-

EMEAToolpath

For the specific pat, the Leadin and Leadout for Contour

Mill Operation is defined at the center of the segment.

However, the toolpath generated is not as per the assigned

Leadin and Leadout values.

23. CW-46845 PR2 Beta2015 UI

In the Operation Parameters dialog box, on the Lead

In/Out tab, when the Leadout type is selected as Same as

Leadin, then the preview panel does not display updated

images to correspond with the image for Leadin type.

24. CW-46844 PR2Beta2015-

EMEAUI

The icon provided for New Feature command does not

visually correspond to other icons on the Command

Manager. The icon needs to be modified in order to

visually sync it with other icons.

25. CW-46831 Beta 2Beta2015-

EMEAOperation

For Multiaxis operations, if parameters are modified on the

Gouge Checking tab of the Operations Parameters dialog

box, then CAMWorks doesnt prompt a Toolpath

Regeneration message on closing the dialog box.

26.CW-46804CW-46781

CW-46753

CW-46740

Beta 2 Beta2015 ConfigurationIn CAMWorks 2015 Beta1, for Mill Parts, when stock isdefined by using another configuration of the part being

machined, then SOLIDWORKS crashes. This is not observed

is Turn module.

27. CW-46803 Beta 2Beta2015-

EMEAFeature

Whenever a Hole group feature defined using a sketch is

deleted and restored, then the hole features are restored

as individual features. Upon doing edit definition of such

restored features, only a single hole feature is displayed in

the graphics area although the selected entities list shows

the name of the sketch used to define the group feature.

28. CW-46802 PR1 Beta2015-EMEA

Toolpath

If a corner round tool is used to machine the top fillet of a

feature and the output through option is set to 'Tip', thenthe resultant toolpath gouges the feature. The gouge is not

seen when the output option is set as 'Tangent'.

29. CW-46801 PR1Beta2015-

EMEASystem

CAMWorks Configurations are not supported for 2.5X

Limited License module type. It should be supported for

this License module also.


5/13

5 | P a g e

Sr.

No.

CPR

NumberCAMWorks

2015 VersionHelp


30. CW-46799 PR1Beta2015-

EMEAToolpath

For the specific Mill part, the VoluMill roughing operation

ignores islands created using sketches.

31. CW-46797 Beta2015-EMEA

Toolpath

In CAMWorks 2015 Beta, for the specific part, the VoluMill

toolpath generated for the Roughing operation gouges 3

circular islands.

32. CW-46795 Beta 2Beta2015-

EMEAFeature

While interactively inserting a 2.5 Axis Mill feature with

islands, when user attempts to define Side Taper for the

Island Entities, the error message An unsupported

operation was attempted is displayed and the 2.5 Axis

Feature Wizard dialog box closes.

33. CW-46793 PR2Beta2015-

EMEAUI

While interactively inserting a 2.5 Axis feature, the End

condition is reset to default values if the user proceeds to

the next dialog in the Wizard and then returns back to the

end condition dialog box.

34. CW-46788 Beta 2Beta2015-

EMEAOperation

While creating a new turn operation, the user can select

tools from the new operation user interface. The available

tool list doesnt get updated when the user changes the

operation type by using the Back button.

35. CW-46771 Beta 2Beta2015-

EMEAAssembly

For the specific assembly file, when user edits the machine

definition, CAMWorks displays an error message Rotary

and Tilt axis cannot be parallel even though these axis are

not parallel. This error message was not observed in

CAMWorks 2014 version.

36. CW-46761 Beta 2 11-2096 Toolpath

For the specific 2.5 Axis Mill Part the Rough Mill toolpath

generated with a stepover of 40% or above and withpattern of pocket out, does not machine the feature

completely.

37. CW-46750 PR2 11-2161 Operation

For Engrave operations, Spline Deviations defined at global

level gets applied. The ability to override this global value

by defining Spline Deviation at operation level is disabled.

In specific cases, it can lead to the engrave toolpath to be

broken into too many segments.

38. CW-46720 SP0 11-2123 Assembly

In assembly mode, if the origin of the Mill par Setup is set

as Top Center and a Coordinate System is selected in the

Machine Definition, then for operations listed under the

Mill Part Setup, the min and Max values of X should ideallybe with respect to the Top Center of the Mill Part Setup.

Instead, these values are derived based on the Coordinate

System in Machine Definition.


6/13

6 | P a g e

Sr.

No.

CPR

NumberCAMWorks

2015 VersionHelp


39. CW-46718 PR2 11-2124 Operation

If user switches to an alternate Tool Crib after a part has

been programmed and selects the Prompt option, then

CAMWorks displays a dialog to assign tools to the

operations from the new tool crib. However, no tools are

listed to choose from.

40. CW-46649 SP0 11-2126 Toolpath

For Mill parts having taper features needing external

threading, the toolpath passes of the thread milling cut the

feature in the reverse method i.e. the resultant toolpath

cuts the final pass of the thread in the beginning. This

behavior is not seen with thread milling done for features

having no taper.

41. CW-46631 Beta 2 11-2116 Post

When a multi axis mill operation with number of axis set to

3, is post processed, the values of clearance plane do not

get posted correctly. The user defined values for clearance

plane are not considered.

42. CW-46610 PR1 11-2111 Features

In mill parts, when Extract Machinable Features is done the

pockets with chamfer on top are detected as tapered

feature. The taper angle is shown as 90 degrees. However,

the user will not be able to use the option of 'Toolpath

center with or without compensation' for such features.

But the option will be available for interactively inserted

features.

43. CW-46609 Beta 2 11-2110 Features

When chamfer is present on a Mill parts edges, then the

Automatic Feature Recognition doesn't recognize the face

feature.

44. CW-46599 PR2 11-2079 Features

For the specific part, when user tries to generate Turn

features using Automatic Feature Recognition with

Revolved Section option, the features generated using a

Mill-Turn machine and Turn machine are different. Results

in both cases are unsatisfactory.

45. CW-46540 SP0 11-2055 ToolpathFor the specific part, the Contour Mill toolpath defined for

the Curve Feature is not following the curve definition.

46. CW-46497 PR2 11-2037 VoluMillFor the specific part, VoluMill does not avoid islands

defined using a sketch.

47. CW-46491 SP0 11-1982 Assembly

For the specific Assembly file, if user updates the Tool Crib

and tries to save the part, then user is unable to save the

CAMWorks data and CAMWorks crashes.

48. CW-46466 PR1 11-2023 Toolpath

For the specific turn part, the Groove finish toolpath is

generated in Turn mode but cannot be generated in Mill-

Turn mode.


7/13

7 | P a g e

Sr.

No.

CPR

NumberCAMWorks

2015 VersionHelp


49. CW-46457 Beta 2 11-2014 TechDB

Within the TechDB, in the Tapping- Rolling Taps database,

for some tap conditions, the values of the Tap drill

diameter is larger than the Major diameter (D1) of tap.

Also, for some tapping conditions, no operations have

been defined in mill mode.

50. CW-46410 SP0 11-1986 Features

For the specific part, when a Mill Part Setup is inserted and

Recognize Features command executed, features are

correctly recognized. However, on inserting another Mill

Part Setup in the opposite direction and executing the

Recognize Features command, the features in the earlier

setup indicate a potential rebuild failure.

51. CW-46365 Beta 2 11-1971 Operation

If the user selects Cancel button in the operation

parameters dialog box after selecting a new tool from the

tool crib, then the changes made to the tool should not be

retained. The older tool and its dimensions should be

retained.

52. CW-46321 Beta 1 11-1955 UI

Add the parameter of body length of the corner round tool

in the preview window. At present the parameter is seen in

the UI of the tool tab as L5.

53. CW-46314 Beta 1 11-1954 Configuration

When renaming SOLIDWORKS Configurations, when user

switches to another Configuration, the configuration that

was renamed reverts back to the original name.

54. CW-46308 Beta 2 11-1949 Toolpath

In CAMWorks 2014 SP 2.1, the Contour Mill toolpath for

rest machining ends up machining the whole feature. This

functionality is working correctly in CAMWorks 2014 SP1.

55. CW-46269 SP0 11-1929 SimulationFor specific mill part, large arc moves are seen during stepthrough simulation. However, the posted NC code is

satisfactory as per the feature geometry.

56. CW-46247 Beta 1 11-1918 Feature

If the dimension of the fillet is less than 0.0026 Inch, then

user cannot pick the fillet entity for interactively defining

an Open Profile feature.

57. CW-46161 Beta 1 11-1608 Post

Change the error message which is shown when posting is

done using a Mill Turn post supporting X positive co-

ordinates only to Error: Exceeded X Minus Limit of X0. Post

may still output the X coordinates.

58. CW-46089 Beta 1 11-1807 Feature

In Mill Assembly Mode, when creating 2.5 Axis Features

interactively using assembly sketches, if the user proceeds

with interactive insertion of the next feature without

closing the New 2.5 Axis Feature dialog box, then the

orientation and placement of the resultant feature is

incorrect.


8/13

8 | P a g e

Sr.

No.

CPR

NumberCAMWorks

2015 VersionHelp


59. CW-46085 Beta 1 11-1826 TechDB

When Additional Amount for Leadin is defined in TechDB

and Generate Operation Plan is done then, the set values

for additional amounts are not reflected in CAMWorks.

60. CW-46026 Beta 1 11-1775 Toolpath

For the specific part machined using CAMWorks 2014

version, the multiaxis toolpath is gouging the part. This

toolpath didnt gouge the part in CAMWorks 2012 version.

61. CW-45992 SP0 11-1774 Translation

In Turn module, for Thread parameter, the choice of

"Program point" -"Tool nose Center" & "Tool nose tip" is

different for Japanese version of CAMWorks when

compared to English Language version.

62. CW-45977 Beta 1 11-1768 Feature

In CAMWorks 2014 SP2.1 version, when a 2.5 Axis Open

Profile feature with the side wall taper is interactively

inserted then, the resultant feature is incorrect.

63. CW-45823 Beta 1 11-1715 UI

In the Post Processor tab of the Machine node dialog box,

the width of the Post Processor selection box needs to be

increased.

64. CW-45679 Beta 2 ---- Toolpaths

The Entry Hole and Entry Drill toolpaths defined for a 2.5

axis operation shouldnt be modified when generate

toolpath command is executed on the 2.5 axis operations

without changing any parameter.

65. CW-45653 Beta 1 11-1629 Post

The post operations do not get post processed when

selected with other operations and posted. But when thepost processing is done for all the operations from

CAMWorks toolbar, they get prost processed.

66. CW-45652 Beta 1 11-1628 UI

When a turn feature is being inserted using Revolved

Section method then, the Turn Section Plane Angle field

should be disabled as it is applicable only to Plane Section

method.

67. CW-45543 Beta 2 11-1552 TechDBFor the Drill Tool with TechDB ID 435, the incorrect tool

description is given. It should be updated to 5/64.

68. CW-45539 Beta 1 11-1549 TechDBIn the Setup tab of the Turn and Mill-Turn MachineDefinition Forms, the 'Global Rotary Retract Plane' field

needs to be removed as it serves no purpose.

69. CW-45456 Beta 1 11-1512 UI

For Contour Mill operations, Additional Amt. fields for

Leadin/Leadout should be disabled when in Units mode.

They should be active only in percentage mode.


9/13

9 | P a g e

Sr.

No.

CPR

NumberCAMWorks

2015 VersionHelp


70. CW-45397 Beta 2 11-1467 Toolpath

For the specific Mill Part, toolpath is not generated for a

Pattern Project operation with pattern type set to

Flowline.

71. CW-44978 PR1 11-1308 PostPost Flags ID and OD do not work, when Canned Cycle

Output is used for turn roughing operations.

72. CW-44930 Beta 2 11-1261 Feature

For the specific Mill-Turn part file, when coordinate system

is selected from the Machine Definition and the Extract

machinable Features command is executed, then

SOLIDWORKS crashes.

73. CW-44920 PR2 11-1237 UI

The Error message indicating potential tool collision

toolpath gouging needs to be updated to indicate which

parameters/settings are invoking this message.

74. CW-44914 Beta 1 11-1216 OperationIn the tool database of thread mill conditions, duplicatethread conditions are observed. This is seen when the user

tries to add a thread condition to the hole feature.

75. CW-44861 Beta 2 11-1174 Feature

In turning, when full rebuild is done, then the join

segments added by the user after modifying a feature

which was recognized earlier by Automatic Feature

Recognition are lost. After rebuild, the user defined join

segments are deleted and the earlier deleted segments of

the feature are added again.

76. CW-44726 PR2 11-1039 TechDB

Thread Mill Condition definitions for spindle type set to

"Sub spindle "within TechDB need to be updated and thethread type set for the Imperial threads in the Metric

database is incorrect and needs to be corrected.

77. CW-44661 SP0 11-0923 FeaturesFor the specific Mill part, toolpaths cannot be generated

for the Part PerimeterBoss feature.

78. CW-44586 Beta 2 11-0986 Post Help

In the Help documentation for Universal Post Generator, it

should be mentioned that the variable OPR_Z_DEPTH is

available only for Drilling cycles and not for Milling cycles.


For a Multiaxis operation, if user sets the Rotate Toolpath

option to xinstances in the Advanced tab of operationParameters dialog box, then user is unable to revert and

turn it off so as to get only one instance of the toolpath.

80. CW-43390 PR2 11-0580 Toolpath

The corner machining option under the side parameters of

a contour mill operation to machine the corners of

features is not working in CAMWorks 2014.


10/13

10 | P a g e

Sr.

No.

CPR

NumberCAMWorks

2015 VersionHelp


81. CW-42854 PR1 10-9349 UI

Whenever a multi surface feature or a turn feature is

inserted by the user, then the user will not get any

information regarding the successful insertion of the

feature. Display a bubble message after the successful

insertion of the feature, when the insert multi surfacefeature wizard and turn feature wizard are in pinned state.


In CAMWorks 2014 SP1 version, in the operation

parameters whenever a tool station number is changed to

an already used tool station number, then the comments

of the tool get overwritten with the comments of another

tool.

83. CW-42641 Beta 1 11-0362 Toolpath

When ignore air segments option is selected for contour

mill operations for slot features and if the avoid area

options are set to "Feed Around" or "Rapid Over", the tool

path gets corrupted.

84. CW-42481 Beta 1 11-0293 Toolpath

For the specific Mill part, when the Pattern type for the

Area Clearance toolpath is set to VoluMill, the resultant

toolpath does not machine most of the large areas.

85. CW-42477 SP0 11-0267 TechDBThe 'Edge Margin' parameter for the Multiaxis Mill

operation should be made available in TechDB.

86. CW-42455 Beta 2 11-0278 System

Provide an ability to define a description for every strategy

in TechDB and in CAMWorks UI. The description should be

user defined in TechDB and for reference purpose in

CAMWorks under the feature parameters dialog box.

87. CW-42250 PR2 11-0179 Assembly

The Mill Part Setup allow the user to define the X axis

direction using an alternate co-ordinate system apart from

the one used to define the Fixture Co-ordinate System on

the machine node.

88. CW-42215 Beta 1 11-0027 Toolpath

In the specific part when a pocket feature is machined

using rough mill operation with 'Stay at Depth' option set

to On, the resultant toolpath leaves wedges.


For the specific Mill part, when user tries to machine the

Corner slot feature after replacing the default tool

assigned with the tool of larger diameter, CAMWorks

crashes.

90. CW-41142 Beta 1 10-9683 Feature

For the specific Mill part, when user tries to interactively

insert irregular pocket features using face entities, then

the feature cannot be inserted. The same feature gets

inserted if a sketch is used to define the base entity.


11/13

11 | P a g e

Sr.

No.

CPR

NumberCAMWorks

2015 VersionHelp


91. CW-41062 SP0 10-9624 Feature

For the specific Mill part, the Roughing and contour Mill

toolpaths generated for Irregular slot features recognized

using AFR end up gouging the part.

92. CW-40815 Beta 1 ---- Turn

In turning when a part is machined using two spindles and

with sub spindle operations then, in step through display,

the sub spindle appears to be moving to home position

after grabbing the part. The correct way is that the main

spindle should return to home position and not the sub

spindle.

93.CW-40544

CW-35284Beta 1

10-9413

10-6824Toolpath

For the specific Mill part, when the Pattern type for the

Area Clearance toolpath is set to VoluMill, the resultant

toolpath gouges the part.

94. CW-40447 Beta 1 10-9028 Rebuild

The feature length for threading operations in turning

doesnt update as per the changes done in the part. The

user will have to manually change the value.

95. CW-40406 Beta 2 10-9335 Features

For the specific Turn part, on executing the Extract

Machinable Features command, the resultant OD Feature

ignores some of the line and arc segments of the part.

96. CW-40344 Beta 2 10-9303 Features

For the specific Mill Part file, Contour Mill toolpaths are

not generated for pocket feature defined through

Automatic Feature Recognition or Interactive Feature

Recognition.

97. CW-40299 Beta 2 10-9264 Features

Simplify the automatic recognition of features which have

intersecting hole features. The user should get the hole

feature separately along with a slot or pocket feature.

98. CW-40115 SP0 10-9203 Features

When 'Extract Machinable Features' is done in assembly,

then the hole thread call outs for features having threads

are not recognized. Instead the hole feature with thread is

recognized as a simple hole feature.

99. CW-39974 Beta 1 10-9145 UI

Whenever an invalid character is entered in the first cut

amount field of rough mill and contour mill operations,CAMWorks displays the error message for 30 times. It

should be displayed only once and shouldnt repeat after

the user closes the error message dialog box.


12/13

12 | P a g e

Sr.

No.

CPR

NumberCAMWorks

2015 VersionHelp


100. CW-39783 Beta 1 10-9050 Rebuild

CAMWorks is not acknowledging model changes for all

CAMWorks configurations. Only the active Configuration is

Rebuilt. No prompt for Rebuilding is displayed for the

other Configurations.

101. CW-39689 SP0 10-9624 Rebuild

For Mill parts, the toolpath for one of the feature instances

within a group feature is not deleted when its feature is

deleted and the part is Rebuilt.

102. CW-39621 Beta 2 10-8955 Toolpath

For the specific Mill part, VoluMill toolpath generated for

the slot feature does not consider the circular islands

which were recognized automatically or interactively.

103. CW-39431 Beta 1 10-8862 TechDB

When user interactively insert a Multi Surface Feature and

sets the strategy to either Area Clearance and ConstantStepover or Constant Stepover, for the resultant

Constant Stepover operation generated, the Offset Curve

strategy in the Pass Options section of the Constant

Stepover tab doesnt match with the corresponding entry

in TechDB.

104. CW-39156 Beta 1 10-8734 ToolpathWhen rough milling is done using the VoluMill pattern, the

islands in the feature get ignored.

105. CW-38791 Beta 1 ---- Toolpath

For the specific mill Part, when VoluMill pattern is applied,

the resultant Rough Mill toolpath ignores the large bossfeature at the center and machines through it.

106. CW-38583 Beta 2 10-8548 TechDB

In CAMWorks 2013, two new material types HP Drilland

U DRILL were added to the TechDB but were arent

added to the Feeds/Speed Library. Consequently, the Feed

and Speed values for these material type is zero. To avoid

this error, these materials should be removed from

TechDB.


For the specific part with Irregular Pocket Feature, when

user executes the Save Operation Plan command and saves

it as a New Feature Condition, CAMWorks crashes.

108. CW-36694 Beta 1 --- ToolpathFor the specific part, the rough mill toolpath with pattern

type set to VoluMill results in a gouge.

109. CW-36531 Beta 1 10-7493 Toolpath

For the specific part, the Roughing toolpath for the

Perimeter-Open Pocket feature doesnt get generated

when the pattern Type is set to VoluMill.


13/13

13 | P a g e

Sr.

No.

CPR

NumberCAMWorks

2015 VersionHelp


110. CW-36478 PR1 ---- Toolpath

In Mill features having islands with height more than the

feature the rough mill toolpath with pattern type set to

VoluMill gouges the feature.

111. CW-32574 Beta 1 10-5846 Toolpath

In the specific part for a perimeter feature of the type

open pocket, rough mill toolpath with pattern set to

VoluMill cannot be generated.

112. CW-31949 Beta 1 10-5408 Toolpath

In Mill assembly mode, when user selects VoluMill as the

Pattern type, the resultant toolpaths do not take into

account the fixtures to be avoided.

113. CW-31692 PR1 10-5204 Toolpath

In mill features if the islands have one or more edges

collinear with the feature edge, then the rough mill

toolpath generated with pattern type set to Volumill

gouges the feature by ignoring the islands.

114. CW-26033 Beta 1 10-1331 Toolpath

When rough mill toolpath is generated with pattern type

set to VoluMill for an open pocket feature having islands

with multiple steps then, the island geometry is not

considered correctly and the resultant toolpath gouges the

islands.

Documents

Cw 2015 Build Info