20' (6.1 m) screen installation for the WM220 dual system

March 2016 2

March 2016 3

#8 ½" screws4 x for the touch module bracket12 x for the L-brackets

6 x L-brackets 8 x 10-32 nuts 2 x frame mounting bracket

4 x #4 ½" screws

4 x #4 nuts

Phillips screwdriver Rubber mallet Level Measuring tape ⅜" open wrenchor socket driver

2 x seam braces

2 x 28" wall brackets

NOTE: At least four people are required to assemble the 20' (6.1 m) screen. To maintain optimal projected image geometry and screen alignment, aflat and straight wall free from obstructions and angular distortions should be used.

Choose a clean work area for assembly using padded material or other soft, clean materials. The work area should be larger than the overall screen size and directly in front of the location where the screen is to be installed.

Preparation

Tools required for assembly

Hardware provided

2 x 44" wall brackets

March 2016 4

2. .

Find (1) seam brace and remove the release liner from both strips of adhesive tape.

Ensuring the panels are still in alignment, line up the seam brace with one of the panel seams with the adhesive side facing down. Do not press the adhesive into the panels yet. Maintain at least a small gap between the adhesive and the panel.

Use a ⅜" open wrench or socket driver and 4 x 10-32 nuts to attach the seam brace onto the studs on the top and bottom of the screen frame at the panel seam. Tighten all four nuts once they are attached to the frame (Figure 1b).

NOTE: For optimal seam alignment, hold the panels together tightly while the seam brace is being adhered and the lock-nuts are being tightened.

Press the adhesive into the panels. Apply steady pressure along the length of the seam brace to attach firmly.

ASSEMBLY INSTRUCTIONS FOR A DUAL SYSTEM Carefully unpack unit and place all panels on top of a cleanwork area. The viewing surface of each panel must face down.

Slide all three panels together, aligning both the top andbottom frames (Figure 1a).

1.

2

3.

4.

5.

6.

Figure 1a

7.

6.

Repeat steps 3-6 to attach the other seam brace.

March 2016 5

PROVIDED WITH WM210

2 xTouch module with cover2 x Touch module bracket4 x Machine screws to attachtouch modules to brackets

Attach the touch module bracket to the frame mounting bracket using the #4 screws and nuts provided (Figure 2a).

Remove the cover from the touch module. Attach the touch module to the touch module bracket using the machine screws provided(Figure 2b). Repeat with the second bracket.

With the screen facing the way it will be when mounted on the wall, use two of the #8 1/2" screws to attach the mounting brackets with the touch modules to the channel in the frame. Ensure that the screws are turned tight enough to securely lock the bracket into place (Figure 2c).

Attach the left touch module 62 3/4" (159 cm) from the left side of the screen to the left mounting hole of the bracket.

Attach the right touch module 63" (160 cm) from the right side of the screen to the left mounting hole of the bracket.

Once attached, the left bracket should be both flush and square withthe frame.

1.

2.

3.

Figure 2a Figure 2b

Figure 2c

Attach the touch module bracket to the frame

March 2016 6

Mount the screen on the wall

1.

2.

NOTE: Use appropriate mounting hardware for the wall type and to accommodate the screen’s total hanging weight of 175 lb. (79.4 kg).

Secure the two center panel wall brackets to wall studs with the appropriate mounting hardware. The outside edge of each wall bracket must be no greater than 5"(13 cm) away from the clef or right panel seams. Ensure the brackets are 77 ¾" (197 cm) from the floor to the mounting holes and 18 ¾" (48 cm) from the top of the projector mounting bracket (with the cover removed) to the mounting holes (Figure 3).

Secure the two side panel wall brackets to wall studs at the height selected in step 1. Each side panel wall brack- et should be centered between the seam brace and left or right outside edge of the frame when mounted to the wall (Figure 3).

Ensure your brackets are level, before securing them. If your brackets are not level a gap may appear between the panels once they are mounted.

3.

Figure 3

To install the (2) center panel L-brackets, you must measure the overall height of the screen frame and subtract 1 1/8"(3 cm). Using that dimension, measure down from the top edge of each of the center wall brackets and mark the wallfor two screw holes. The outside edge of each center panelL-bracket must be no greater than 5" (13 cm) away from theleft or right panel seams (Figure 3).

Secure the two center panel L-brackets to the wall at the marked locations. The longest side of the two center panelL-brackets should be pointing upward when secured to hide the L-brackets behind the screen frame once the screen is installed (Figure 3).

Repeat steps 3-4 to install the (4) remaining L-brackets for the side panels.

4.

March 2016 7

Tap the bottom of the L-brackets with the rubber mallet untilthey make contact with the frame. Secure the L-brackets to the frame with the remaining #8 x 1/2" screws (Figure 4).

5.

Mount the screen on the wall (continued)

Using four people, carefully and in a smooth motion lift thescreen to hang it on the wall brackets. There is a lip on the back of the frame that wedges itself into the four wall brackets once full installed. Ensure that the screen clears the L-brackets and that the screen weight is on the wall brackets, not the L-brackets.

NOTE: Any bend between the three panels at the seamsmay damage the screen or result in a permanent gapbetween the seams. When lifting the screen off of the clean work area to the wall and then onto the wall, it is crucial that the screen remain coplanar and does not bend at the seams.

6.

Figure 4

March 2016 8

10' (3.1 m) screen installation for the WM210 single system

March 2016 9

#8 ½" screws2 x for the touch module bracket8 x for the L-brackets

4 x L-brackets 4 x 10-32 Nuts 1 x Frame mounting bracket

2 x #4 ½" screws

2 x #4 nuts

Phillips screwdriver Rubber mallet Level Measuring tape ⅜” open wrenchor socket driver

1 x seam brace

4 x 28" wall brackets

NOTE: At least three people are required to assemble the 10' (3.1 m) screen. To maintain optimal projected image geometry and screen alignment, a flat and straight wall free from obstructions and angular distortions should be used.

Choose a clean work area for assembly using padded material or other soft, clean materials. The work area should be larger than the overall screen size and directly in front of the location where the screen is to be installed.

Preparation

Tools required for assembly

Hardware provided

March 2016 10

March 2016 11

2. .

Remove the release liner from the adhesive tape on the seam brace.

Ensuring the panels are still in alignment, line up the seam brace to the panel seam with adhesive side facing down. Do not press the adhesive into the panels yet. Maintain at least a small gap between the adhesive and the panel.

Use a ⅜" open wrench or socket driver and 4 x 10-32 nuts to attach the seam brace onto the studs on the top and bottomof screen frame at the panel seam. Tighten all four nuts onceattached to the frame (Figure 1b).

NOTE: For optimal seam alignment, hold the panels together tightly while the seam brace is being adhered and the lock-nuts are being tightened.

Press the adhesive into the panels. Apply steady pressure along the length of the seam brace to attach firmly.

ASSEMBLY INSTRUCTIONS FOR A SINGLE SYSTEM Carefully unpack unit and place all panels on top of the cleanwork area. The viewing surface of each panel must face down.

Figure 1a

Figure 1b

Slide the two panels together, aligning the both the top andbottom frames (Figure 1a).

1.

2

3.

4.

5.

6.

March 2016 12

PROVIDED WITH WM210

1 x Touch module with cover1 x Touch module bracket2 x Machine screws to attachtouch module to bracket

Attach the touch module bracket to the frame

Attach the touch module bracket to the frame mounting bracket using the #4 screws and nuts provided (Figure 2a).

Remove the cover from the touch module. Attach the touch module to the touch module bracket using the machinescrews provided (Figure 2b).

With the screen facing the way it will be when mounted on the wall, attach the touch module bracket to the channelin the frame 60 ¼" from the left side of the frame to the left hole in the mounting bracket.

Use two of the #8 ½" screws to attach the mounting bracket to the channel in the frame. Ensure that the screws are turned tight enough to securely lock the bracket into place (Figure 2c).

1.

2.

3.

Figure 2a Figure 2b

Figure 2c

March 2016 13

Mount the screen on the wall

1.

2.

your brackets are not level a gap may appear between the panels once they are mounted.

NOTE: Use appropriate mounting hardware for the wall type and to accommodate the screen’s total hanging weight of 85 lb. (38.5 kg).

The four wall mounting brackets are hung with 2 ⅛" (15 cm) between each one.

Find the system centerline and make a mark 1 1/6" (3cm) on one side of the centerline. Line up the edge of one of the brackets with the mark, ensure it is level, then mark the bracket mounting holes.

Before securing the bracket to the wall, use the marksto ensure the bracket is 77 ¾" (197 cm) from the floor to the mounting holes, and 18 ¾" (48 cm) from the top of the projector mounting bracket (with the cover removed)to the mounting holes.

Secure that bracket to the wall with the appropriate mounting hardware.

Secure the remaining four brackets 2 ⅛" apart. Ensure your brackets are level before securing them (Figure 3). If

3.

To install the 4 L-brackets, you must measure theoverall height of the screen frame and subtract 1 1/8" (3cm).Using that dimension, measure down from the top edge of each of the wall brackets and mark the wall for twoscrew holes. The outside edge of L-bracket must be nogreater than 5" (13 cm) away from outside edges of the screen.

Secure the L-brackets to the wall at the marked locations. The longest side of the L-brackets should be pointing

upwards when secured in order to hide the L-brackets behind the screen frame once the screen is installed (Figure 3).

Figure 3

March 2016 14

Tap the bottom of the L-brackets with the rubber mallet until they make contact with the frame. Secure the L-brackets to the frame with the remaining #8 1/2" screws (Figure 4).

5.

Mount the screen on the wall (continued)

Using three people, carefully and in a smooth motion lift thescreen to hang it on the four installed wall brackets. There is a lip on the back of the frame that wedges itself into the four wall brackets once full installed. Ensure that the screen clears the four L-brackets and that the screen weight is on the four wall brackets, not the L-brackets.

NOTE: Any bend between the two panels at the seammay damage the screen or result in a permanent gapbetween the seam. When lifting the screen off of the clean work area to the wall and then onto the wall, it is crucial that the screen remain coplanar and does not bend at the seams.

6.

Figure 4

March 2016 15

Cleaning

Everyday Cleaning: The supplied foam eraser can be used to clean marks on the screen surface made by everyday dry erase marker

usage. Do not use spray cleaner in combination with the foam eraser.

Thorough Cleaning: For periodic full screen cleaning or to clean persistent marks from dry erase markers, use the supplied Da-Lite

spray cleaner and cleaning cloth. Use clean or dry sections of the microfiber cloth when erasing the screen. This is important to prevent

smearing on the screen while cleaning. To clean permanent markers and other unintentional marks on the surface, use the supplied

foam eraser or the Da-Lite spray cleaner and cleaning cloth.

March 2016 16

LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS

Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in

materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly

operated according to Da-Lite’s instructions and are not damaged due to improper handling or treatment after shipment from the

factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered

with or repaired by a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.

Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,

transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.

To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of fitness for use,

or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives

you specific legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED

BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION

OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Customer Care Specialists at

3100 North Detroit Street, Warsaw, IN 46582, (574) 267-8101, (800) 622-3737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS

WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

28408

A Milestone AV Technologies Brand

3100 North Detroit Street

Warsaw, Indiana 46582

P: 574.267.8101 or 800.622.3737

F: 574.267.7804 or 877.325.4832

E: info@da-lite.com

www.da-lite.com

DL–0489 (Rev. 5) 08.15

© 2015 Milestone AV Technologies LLC. Printed in U.S.A.March 2016 17