The Measurable Difference

DATA SHEETMXR Analog

Temposonics®

Magnetostrictive Linear Position Sensors

– External mounting for new or retrofit designs

– Rugged, up to 100 g shock and 15 g vibration levels

– Flexible, capability to measure a range from 100 to 600 mm

Data sheetMXR Sensor

I 2 I

Technical data

The MH-Series Model MXR sensor is available in two versions. The MXRC and the MXRS. Although the two versions are similar in both appear-ance and performance, there are unique features distinguishing the two sensors from one another. The MXRC is available in four discrete stroke lengths up to 250 mm, while the MXRS is available in stroke lengths up to 600 mm (50 mm ordering increments). The MXRC works with a 5 VDC operating voltage, and provides a voltage output that is ratiometric to the operating voltage. The MXRS can work with an operating voltage of either 12 or 24 VDC, and has multiple analog output options available.

Product overview

MXRS MXRC

Input

Measured value Linear Position measurement Linear Position measurement

Stroke length 100…500 mm 109.5 mm, 148.0 mm, 217.3 mm, and 250.1 mm

Output

Voltage 0.25…4.75 VDC, 0.5…4.5 VDC 0.1…4.9 VDC at +5 VDC supply, ratiometric with V supply

Current 4…20 mA –

Accuracy

Resolution ±0.10 mm ±0.10 mm

Linearity < ±0.04 % F.S. ±0.3 mm

Repeatability < ±0.1 mm < ±0.1 mm

Hysteresis ±0.1 mm ±0.1 mm

Operating conditions

Operating temperature −40…+105 °C −40…+75 °C

Storage temperature −30…+105 °C −20…+85 °C

Humidity 90% relative humidity, no condensation 90% relative humidity, no condensation

Ingress protection IP69K with M12 approved connector IP69K with M12 approved connector

Shock test* 100 g (single hit) / IEC standard 68-2-27 (survivability)

5 g (single hit) / IEC standard 68-2-27 (survivability)

Vibration test* 15 g / 10…2000 Hz / IEC standard 68-2-6 1 g / 10…150 Hz / IEC standard 68-2-6

EMC test ISO 14982 100 V/m (radiated immunity) Emmissions: EN61000-6-4Immunity: EN61000-6-2

Design/Material

Sensor electronics housing Stainless steel 1.4305 / AISI 303 Stainless steel 1.4305 / AISI 303

Sensor rod with flange Stainless steel 1.4306 / AISI 304L Stainless steel 1.4306 / AISI 304L

Installation

Mounting Threaded M10×1.5 studOptional Ball Joint or Spherical Rod End

Threaded M10×1.5 studOptional Ball Joint or Spherical Rod End

Electrical connection

Connection type M12 connector (male) M12 connector (male)

Electrical isolation 500 VDC (DC ground to machine ground) 500 VDC (DC ground to machine ground)

Operating voltage 12/24 VDC (8…32 VDC) 5 VDC (4.75…5.5 VDC)

Current consumption Typical < 80 mA (12 VDC);Typical < 40 mA (24 VDC) Typical < 40 mA (5 VDC)

Polarity protection Up to −36 VDC VDC to GND

Overvoltage protection Up to 36 VDC Up to 20 VDC

* The vibration and shock rating is stated for a fully retracted sensor. The rating for full or partially extended sensor depends on the application

Data sheetMXR Sensor

I 3 I

Model MXR (rod retracted)

Figure 1. MH-Series Model MXR sensor dimension reference (Model MXRS shown)

Model MXR sensor dimension references

Drawing is for reference only, contact applications engineering for tolerance specific information.

Model MXR (rod extended)

Drawing is for reference only, contact applications engineering for tolerance specific information.

Figure 2. MH-Series Model MXR sensor dimension reference (Model MXRC shown)

Electric ‘pin to pin’ = (electric stroke (es)×2 + 153.2)

MXRC (ES +4.4)MXRS (ES +10.7)

21.415.8M10×1.5 - 6 g

20.0Electric ‘pin to pin’ = (electric stroke (es) + 153.2)

MXRC (4.4)MXRS (10.7) M10×1.5 - 6 g

Ø28.0

19.82.0

M12×1 - 6 g

Connections and wiring

Connection Type The Temposonics® M12 integrated connector (shown in Figure 3), meets the most stringent protection requirements important for the difficult environmental conditions of mobile hydraulics applications. Protection type IP69K makes the robust metal housing not only completely dust and waterproof, even the harshest cleaning measures cannot damage the sensor.

Table 1. PIN assignmentsFigure 3. M12×1 connector key orientation

Connector PIN Assignment Reference

34

21

Integrated connector (male) as viewed

when looking at the sensor

Standard Integrated connector

Pin assisgnment and function

N_E 4-pin M12×1 2-3-4; Power, ground, output

N_G 4-pin M12×1 1-3-4; Power, ground, output

N_H 4-pin M12×1 1-3-2; Power, ground, output

M12×1 key orientation

1

5

2

6

Data sheetMXR Sensor

I 4 I

SENSOR MODEL M X R 1-3MXR = Externally mounted sensor with self-contained housing

SENSOR STYLES = S 4S = Version S Electronics

STROKE LENGTH (ORDER LENGTH) M 5-8

— — — M = Millimeters100…500 mm in 50 mm increments

CONNECTION TYPE N 9-11

N _ _ = Integrated:

Key orientations (See Figure 3) (90° M12 connector plugged):

MOUNTING HARDWARE = 12A = No Additional Hardware

B = 2 × Ball Joint Ends with 2 × M10 Hex Nuts

C = 2 × Spherical Ball Ends with 2 × M10 Hex Nuts

INPUT VOLTAGE = 3 133 = +12/24 VDC

OUTPUT 14-16

Voltage:

V11 = 0.25…4.75 VDC

V12 = 0.5…4.5 VDCCurrent:

A01 = 4…20 mA

M X R

1 32

S

4

M

5 76 8

N

9 1110 12 13 14 1615

3

=

=

1 Connector key at 0°2 Connector key at 45°

5 Connector key at 180°6 Connector key at 225°

N _ EN _ GN _ H

M12×1, IP69K, 4 pin (pin assignment 2-3-4)M12×1, IP69K, 4 pin (pin assignment 1-3-4)M12×1, IP69K, 4 pin (pin assignment 1-3-2)

=

=

Model MXRS ordering informationUse the table below to configure your sensor part number.

==

==

===

Termination type and pin assignment (See Table 1):

N = Integrated M12×1 connector

Data sheetMXR Sensor

I 5 I

SENSOR MODEL M X R 1-3MXR = Externally mounted sensor with self-contained housing

SENSOR STYLES = C 4C = Version C Electronics

STROKE LENGTH (ORDER LENGTH) M 5-8

— — — M = Millimeters

CONNECTION TYPE N 9-11

N _ _ = Integrated:

Key orientations (See Figure 3) (90° M12 connector plugged):

MOUNTING HARDWARE = 12A = No Additional Hardware

B = 2 × Ball Joint Ends with 2 × M10 Hex Nuts

C = 2 × Spherical Ball Ends with 2 × M10 Hex Nuts

INPUT VOLTAGE = 5 135 = +5 VDC

OUTPUT 14-16

Voltage:

VC1 = 0.1…4.9 VDC at +5 VDC supply, output ratiometric with V supply

M X R

1 32

C

4

M

5 76 8

N

9 1110 12 13 14 1615

5

=

=

1 Connector key at 0°2 Connector key at 45°

5 Connector key at 180°6 Connector key at 225°

N _ EN _ GN _ H

M12×1, IP69K, 4 pin (pin assignment 2-3-4)M12×1, IP69K, 4 pin (pin assignment 1-3-4)M12×1, IP69K, 4 pin (pin assignment 1-3-2)

=

=

109 109.5 mm stroke148 148.0 mm stroke

217 217.3 mm stroke250 250.1 mm stroke

==

==

Model MXRC ordering informationUse the table below to configure your sensor part number.

==

==

===

N = Integrated M12×1 connector

Termination type and pin assignment (See Table 1):

V C 1

V C 1

Data sheetMXR Sensor

I 6 I

Accessory selections

Mounting accessories available for the Model MXR sensor.

Spherical Rod End Dimension reference Part number

43 mm

20 mm

19 mm

28 mm

ThreadM10×1.50

17.1 mm

50 º ConeMin.

12.4 mm

13.9 mm

14.3 mm

9.9 mm

dia.

Spherical Rod End500035

Spherical Rod End Kit(includes 2 rod ends

and 2 hex nuts)201947

Ball Joint End Dimension reference Part number

17.5 mm

22.2 mm

19 mm

16 mm

ThreadM10×1.50

Housing ThreadM10×1.50

35 º

34.9 mm

13 mmHex

7.8 mm

42.9 mm Ball Joint End500036

Ball Joint End Kit(includes 2 Ball Joints

and 2 Hex Nuts)201948

M10 Hex Nut Dimension reference Part number

17 mm

M10×1.5 Thread

8 mm 561788

Data sheetMXR Sensor

I 7 I

Accessory selections (Cont.)

Optional accessories available for the Model MXR sensor.

MH-Series Analog/PWM Tester, part no.: 280618

MH-Series Analog/PWM Tester Part number

The MH-Series Tester includes:• MH-Series analog / PWM Tester• 12 VDC battery charger with (adapter main plug

North America, adapter main plug EU or adapter main plug UK)

• Cable with M12×1 connector • Cable with pigtailed wires• Carrying case• CD-Rom with user’s guide

280 618

Document Part Number: 551601 Revision A (EN.EU) 04/2014

MTS and Temposonics® are registered trademarks of MTS Systems Corporation. All other trademarks are the property of their respective owners. Printed in Germany. Copyright © 2014 MTS Sensor Technologie GmbH & Co. KG. Alterations reserved. All rights reserved in all media. No license of any intellectual property rights is granted. The information is subject to change without notice and replaces all data sheets previously supplied. The availability of components on the market is subject to considerable fluctuation and to accelerated technical progress. Therefore we reserve the right to alter certain components of our products depending on their availability. In the event that product approbations or other circumstances related to your application do not allow a change in components, a continuous supply with unaltered components must be agreed by specific contract.

LOCA

TION

S

LEGA

L NO

TICE

SGERMANYMTS Sensor TechnologieGmbH & Co. KGAuf dem Schüffel 958513 Lüdenscheid, GermanyTel. + 49 2351 9587-0Fax + 49 2351 56491info.de@mtssensors.comwww.mtssensor.de

USAMTS Systems CorporationSensors Division3001 Sheldon DriveCary, N.C. 27513, USATel. +1 919 677-0100Fax +1 919 677-0200info.us@mtssensors.comwww.mtssensors.com

JAPANMTS Sensors Technology Corp.737 Aihara-machi, Machida-shi, Tokyo 194-0211, JapanTel. + 81 42 775-3838Fax + 81 42 775- 5512info.jp@mtssensors.comwww.mtssensor.co.jp

FRANCEMTS Systems SASZone EUROPARC Bâtiment EXA 16 16/18, rue Eugène Dupuis94046 Creteil, FranceTel. + 33 1 58 4390-28Fax + 33 1 58 4390-03info.fr@mtssensors.comwww.mtssensor.com

ITALYMTS Systems Srl.Sensor Division Via Camillo Golgi, 5/725064 Gussago (BS), Italy Tel. + 39 030 988 3819Fax + 39 030 982 3359info.it@mtssensors.comwww.mtssensor.com

CHINAMTS Sensors Room 504, Huajing Commercial Center, No. 188, North Qinzhou Road 200233 Shanghai, ChinaTel. +86 21 6485 5800 Fax +86 21 6495 6329info.cn@mtssensors.comwww.mtssensors.cn