Upload
jlnavarro
View
223
Download
0
Embed Size (px)
Citation preview
7/26/2019 Datalogic DS 4600 A
1/59
DS4600A
Reference Manual
7/26/2019 Datalogic DS 4600 A
2/59
7/26/2019 Datalogic DS 4600 A
3/59
DS4600A
INSTALLATION MANUAL
7/26/2019 Datalogic DS 4600 A
4/59
DATALOGIC S.p.A.Via Candini 240012 Lippo di Calderara di Reno
Bologna - Italy
DS4600A Reference Manual
Ed.: 06/2003
7/26/2019 Datalogic DS 4600 A
5/59
CONTENTS
GUIDE TO INSTALLATION ...........................................
GENERAL VIEW ............................................................
SAFETY PRECAUTIONS...............................................Laser Safety...................................................................Power Supply.................................................................
1 GENERAL FEATURES ..................................................1.1 Introduction ....................................................................1.2 Description.....................................................................
1.3 Available Models............................................................1.4 Accessories....................................................................
2 INSTALLATION..............................................................2.1 Package Contents...........................................................2.2 Mechanical Installation...................................................2.3 Electrical Connections ...................................................
2.3.1 Power Supply.................................................................2.3.2 Main Serial Interface ......................................................
RS232 Interface ..............................................................RS485 Full-Duplex Interface...........................................RS485 Half-Duplex Interface ..........................................20 mA Current Loop (INT-24 Accessory Only)................
2.3.3 Auxiliary RS232 Interface................................................
2.3.4 Inputs .............................................................................2.3.5 Outputs ..........................................................................2.4 Positioning .....................................................................2.5 Typical Layouts ..............................................................2.5.1 Point-to-Point .................................................................2 5 2 Pass Through
7/26/2019 Datalogic DS 4600 A
6/59
3 READING FEATURES
3.3 Performance ..................................................................3.4 Reading Diagrams .........................................................
4 MAINTENANCE..............................................................4.1 Cleaning..........................................................................
5 TECHNICAL FEATURES ...............................................
7/26/2019 Datalogic DS 4600 A
7/59
GUIDE TO INSTALLATION
The following can be used as a checklist to verify all of the complete installation of the DS4600A scanner.
1) Read all information in the section "Safety Precautions" at manual.
2) Correctly position and mount the scanner for barcode readinformation in paragraphs 2.2, 2.4 and 3.4.
3) Provide correct system cabling according to the signals application (see the applicable sub-paragraphs under 2.3).
4) Install the WinHost Configuration program from the CD.Upon successful completion of the installation, the readme fdetails about how to get started configuring your scanner.See also the Guide to Rapid Configuration link in the Help OnSpecific parameter details are also available in the Help On L
NOTE
Fine tuning of the scanner position for barcodeaccomplished using the Test Mode as described in
The installation is now complete.
7/26/2019 Datalogic DS 4600 A
8/59
GENERAL VIEW
DS4600A
DS4600A - 2XXX Models
DS4600A - 3
Figure A
1
4
5
6
7
89
10
11
7/26/2019 Datalogic DS 4600 A
9/59
SAFETY PRECAUTIONS
LASER SAFETY
The following information is provided to comply with the international authorities and refers to the correct use of the DS46
Standard Regulations
This scanner utilizes a low-power laser diode. Although staringbeam momentarily causes no known biological damage, avoid stone would with any very strong light source, such as the sun.
beam hits the eye of an observer, even through reflective surfaetc.
This product conforms to the applicable requirements of both EN21 CFR 1040 at the date of manufacture. The scanner is classifieproduct according to EN 60825-1 regulations and as a Claaccording to CDRH regulations.
There is a safety device which allows the laser to be switched orotating above the threshold for its correct scanning speed.
The laser beam can be switched off through a software comWinHost Help On Line).
WARNING
Use of controls or adjustments or performance ofthan those specified herein may result in exposvisible laser light.
7/26/2019 Datalogic DS 4600 A
10/59
The laser light is visible to the human eye and is emitted from the
of the scanner (Figure A, 2).Warning labels indicating exposure to laser light and the deviapplied onto the body of the scanner (Figure A, 4 and 10).
DATALOGIC S.p.A. Via Candini, 240012 LIPPO DI CALDERARA (BO) ITALY
Model No. Serial No.
Volt Amp.
Manufactured
This product conforms to the applicable req21CFR1040 at the date of manufacture.
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCTMAXIMUM OUTPUT RADIATION 1 m
EMITTED WAVE LENGTH 630~680 n
TO IEC 825-1 (1993)
Warning and device class labels
For installation, use and maintenance it is not necessary to open
The laser diode used in this device is classified as a class 3B lasto EN 60825-1 regulations and as a Class IIIb laser product regulations. As it is not possible to apply a classification label on in this device, the following label is reproduced here:
LASER LIGHT
AVOID EXPOSURE TO BEAM
CLASS 3B LASER PRODUCT
7/26/2019 Datalogic DS 4600 A
11/59
POWER SUPPLY
- This product is intended to be installed by Qualified Perso
- Model DS4600A-XXX0:This device is intended to be supplied by a UL Listed DirUnit marked "Class 2", rated 10-30 V, minimum 0.60 A.
This device may also be supplied by a UL Listed Power Un
LPS power source which supplies power directly to the scconnector.
- Model DS4600A-2XX5:This device is intended to be supplied by a UL Listed DirUnit marked "Class 2", rated 24 V, minimum 0.50 A.
This device may also be supplied by a UL Listed Power Un
LPS power source which supplies power directly to the scconnector.
See par. 2.3.1 for correct power supply connections.
7/26/2019 Datalogic DS 4600 A
12/59
7/26/2019 Datalogic DS 4600 A
13/59
GENERAL FEATURES
1 GENERAL FEATURES
1.1 INTRODUCTION
The DS4600A is a compact laser scanner complete with decproduced to be a flexible and affordable solution for all medihandling applications.
Standard Application Program
A Standard Application Program is factory-loaded onto the DS4controls barcode reading, serial port interfacing, data formattoperating and control parameters.
It is completely user configurable from a host computer using thutility program provided on CD with the scanner or usinprogramming procedure, by ESC sequences via the serial interfa
There are four different programmable operating modes to sreading system requirements. Included in these is a test mode features and exact positioning of the scanner without using exter
Programmability
If your requirements are not met by the Standard ApplicatioApplication Programs can be developed by your local Datalogic d
7/26/2019 Datalogic DS 4600 A
14/59
1
1.2 DESCRIPTION
Some of the main features of this scanner are given below:
long-range reading
scanning speed 800 scans/sec
completely configurable from host computer
2 serial communication interfaces
reads most popular codes
supply voltage from 10 to 30 Vdc
test mode to verify the reading features and exact positiowithout the need for external tools
configurable in different operating modes to suit the most varsystem requirements
code verifier
possibility to detect the position of the label in the scan line
The DS4600A scanner uses a solid state laser diode as a ligemitted has a wavelength between 630 and 680 nm. Refer toPrecautions" at the beginning of this manual for information on la
The reader is contained in a rugged aluminum housing; the meare 101 x 83.5 x 42 mm and it weighs about 615 g.
The protection class of the enclosure is IP65, therefore the rsuitable for industrial environments where high protection agconditions is required.
7/26/2019 Datalogic DS 4600 A
15/59
GENERAL FEATURES
Electrical connection is provided through a cable on the side of t
is terminated with a 25-pin connector (see Figure A, 1).The laser beam output window is on the right hand side of the sc
A security system allows the laser to activate only once the mocorrect rotational speed; consequently the laser beam is gendelay from the power on of the scanner.
The four LEDs on the left hand side of the scanner indicate the fo
READY (red), indicates the reader is connected to the pstartup was successful. If the startup is not sblinks. (Figure A, 9).
GOOD READ (red), is used to signal successful barcode dec
in Test mode to signal the decoding percentagthe WinHost Help On Line). (Figure A, 8).
EXT TRIG (yellow), indicates external trigger activity par. 2.3.4. (Figure A, 7).
TX DATA (green), indicates data transmission on the ma
(Figure A, 6).
The screw holes on the body of the reader are for mechanical the screw holes shown in Figure A, 3 are to attach accessories 90 mirror.
7/26/2019 Datalogic DS 4600 A
16/59
1
1.3 AVAILABLE MODELS
The DS4600A scanner is available in versions that differ in regcharacteristics:
Decoding Mode Special Features
Reading Range Linear or Raster read
The following models are therefore available:
DS4600A - XXXX
Decoding Mode
2 = Standard w/ Display
3 = Advanced Code Reconstruction
Reading Range
0 = Medium Range
1 = Long Range
2 = Short Range
Special F
0 = Standa5 = Integra
Linear/Ra
0 = Linea
1 = Raste
2 = Raste
1.4 ACCESSORIES
The following accessories are available on request for the DS460 Connection Box C-Box 1
Connection Box Profibus C-Box 3
90 deflection mirror GFC 41
7/26/2019 Datalogic DS 4600 A
17/59
INSTALLATION
2 INSTALLATION
2.1 PACKAGE CONTENTS
Verify that the DS4600A reader and all the parts supplied withpresent and intact when opening the packaging; the list of parts i
DS4600A reader with cable
Quick Reference Guide
Barcode Test Chart
WinHost CD
Mounting kit: - Mounting screws and washers (4 ea.)- Mounting bracket (1)
7/26/2019 Datalogic DS 4600 A
18/59
2
2.2 MECHANICAL INSTALLATION
DS4600A can be installed to operate in different positions. T(M4 x 5) on the body of the reader are for mechanical fixture (Fig
The diagram below gives the overall dimensions of the scanner its installation.
Refer to paragraph 2.4 for correct positioning.
100.39
41.8
1.64
M4 N 4
371.47
50.2
11.
8
0.
46
8
1
3.19
8.
25
0.3
2
87.
9
3.4
6
M4 N2
58
2.
28
32.
5
1.
28
3.750.15
421.65
20
0.
79
83.53.29
10
1
3.9
8
18
0.
70
0.9023
DS
37
20.2
1.4
6
22*
0.86
0.8
14.80.58
39.
4
1.5
5
* The quote refers to the scanMounting hole depth M4 X 5
Figure 2 - Overall Dimensions for 2XXX Models
100.39
41.81.64
81
3.1
9
8.
25
0.
32
87.9
3.
46
M4 N2
58
2.
28
37
20.2
1.4
6
18*
0.71
0.814.80.58
39.
4
1.5
5
101
3.98
20
0.
79
3.2983.5
7/26/2019 Datalogic DS 4600 A
19/59
INSTALLATION
5.5
0.
22
115
4.
53
57.3
2.26
5.5
0.2210
5
39
1.
54
5.
5
0.
22
3
0.
12
5.5
0.22
35
0.20
Figure 4 - Mounting Bracket Dimensions
7/26/2019 Datalogic DS 4600 A
20/59
2
2.3 ELECTRICAL CONNECTIONS
DS4600A is equipped with a cable terminated by a 25-pin connection to the power supply and input/output signals. The detpins are indicated in the following table:
CAUTION
Do not connect GND and SGND to different references. GND and SGND are internally co
filtering circuitry which can be permanently damagvoltage drops over 0.8 Vdc.
Figure 3 - 25-pin D-sub Connector
25-pin D-sub connector pinout
Pin Name Function
13 VS Power supply input voltage +
25 GND Power supply input voltage -1 CHASSIS Chassis Ground9 VS External Trigger supply voltage +
18 EXT TRIG+ External Trigger +19 EXT TRIG- External Trigger -6 IN1 + Input 1 +
10 IN1 - Input 1 -14 IN2 + Input 2 +
15 IN2 - Input 2 -8 OUT1 + Output 1 +22 OUT1 - Output 1 -11 OUT2 + Output 2 +12 OUT2 - Output 2 -20 RXAUX Auxiliary RS232 input
7/26/2019 Datalogic DS 4600 A
21/59
INSTALLATION
2.3.1 Power Supply
Power can be supplied to the scanner through the pins proconnector used for communication with the host (Figure 4):
DS4600A
13
25
VS
GND
1CHASSIS
Earth Ground
USER INT
CHAS
GND
V+ (1
Figure 4 - Power Supply Connections
or through the jack connector on the side of the 25-pin connectorUL Listed Direct Plug-in Power Unit (Figure 5). If the jack inppower to the DS4600A, pin 13 is automatically disconnected; th
the external trigger remains on pin 9. The plug connector is nDS4600A.
V+ (10 - 30 Vdc)
Jack Plug
GND
7/26/2019 Datalogic DS 4600 A
22/59
2
2.3.2 Main Serial Interface
The signals relative to the following serial interface types ainput/output connector:
RS232
RS485 FULL DUPLEX
RS485 HALF DUPLEX
An active 20-mA Current Loop interface is available if the optionis installed. This accessory interface replaces the RS232/RS485
The main serial interface type and its relative parameters (betc.) are selected via software either using the WinHost utiliMode programming. For more details refer to the section "Min the WinHost Help On Line.
Details regarding the connections and use of the main interface sthe next paragraphs.
RS232 Interface
The serial interface is used in this case for point-to-point concommunication with the host computer and allows both transmand the configuration of the scanner. This is the default interface
The following pins of the 25-pin connector are used for RS232 in
Pin Name Function
2 TX232 transmitted data3 RX232 received data4 RTS232 t t d
7/26/2019 Datalogic DS 4600 A
23/59
INSTALLATION
RTS/CTS HARDWARE HANDSHAKING ENABLED
DS4600A USER INTE
7 SGND MainSGND
RTS2324DCD
CTS2325DTR
RX2323TXD
TX2322RXD
EarthGround
Figure 6 - RS232 Main Interface Connections
The RTS232 and CTS232 signals control data transmission aconnected devices.
7/26/2019 Datalogic DS 4600 A
24/59
2
RS485 Full-Duplex Interface
The RS485 full-duplex (5 wires + shield) interface is ucommunication protocols in point-to-point connections over lon1200 m / 3940 ft) than those acceptable for RS232 communicatnoisy environments.
The following pins of the 25-pin connector are used forcommunications:
Pin Name Function
2 TX485+ RS485 transmitted data4 TX485- RS485 transmitted data3 RX485+ RS485 received data +5 RX485- RS485 received data -
7 SGND Main signal ground main inte
DS4600A USER INTE
7 SGND Main
TX485+2
TX485-4
RX485+3
RX485-5
RX485
TX485
RS485REF
EarthGroun
Figure 8 - RS485 Full-Duplex Connections
7/26/2019 Datalogic DS 4600 A
25/59
INSTALLATION
RS485 Half-Duplex Interface
The RS485 half-duplex (3 wires + shield) interface is used for pprotocols.
It can be used for Multidrop connections in a master/slave layouMultiplexer, (see par. 2.5.4 and 2.5.5).
The following pins of the 25-pin connector are used for communications:
Pin Name Function
2 RTX485+ RS485 transmitted/received4 RTX485- RS485 transmitted/received7 SGND Main signal ground main interface
DS4600A MULTIPLE
RTX485+2
RTX485-4
RTX485+
RTX485-
7 SGND Main RS485R
Figure 9 - RS485 Half-Duplex Connections
7/26/2019 Datalogic DS 4600 A
26/59
2
The figure below shows a multidrop configuration with DS4600A to a Multiplexer.
1
1CHASSIS
# 1
RTX485+
RTX485-
SGND Main# 0
three wires+ shield
7
4
2
7
4
2
120 Ohm
MULTIPLEXER
RTX485+
RTX485-
RS485REF
SHIELD
1
120 Ohm
DS4600A
(up to 31)
# x
max. 2 m.
7
4
2
DS4600A
DS4600A
7/26/2019 Datalogic DS 4600 A
27/59
INSTALLATION
20 mA Current Loop (INT-24 Accessory Only)
When the INT-24 accessory board is installed, the DS4600A20 mA active current loop interface.
The following pins of the 25-pin connector are used for the connec
Pin Name Function
4 CLOUT- current loop output5 CLIN- current loop input7 SGND Main signal ground main inte
DS4600A USER INTERF
MAX. 300 METERS
4 C.L. OUT -
7 SGND Main GND
I = 20 mA
5 C.L. IN -
I = 20 mA
+
+
Figure 11 - 20 mA Active C.L. Connections
For 20 mA passive current loop interface connections, contact representative.
7/26/2019 Datalogic DS 4600 A
28/59
2
2.3.3 Auxiliary RS232 Interface
The auxiliary serial interface is used exclusively for Rconnections.
The parameters relative to the auxiliary interface (baud rate, dataparticular communication modes such as Local Echo can beWinHost utility program or Host Mode programming. For mparagraph 2.5 and to the section "Auxiliary Interface Menu" in thLine.
The following pins of the 25-pin connector are used to connectinterface:
Pin Name Function
20 RXAUX auxiliary RS232 received d21 TXAUX auxiliary RS232 transmitte23 SGND Aux signal ground auxiliary inte
SGND
DS4600A USER INTE
TXD
RXAUX20
RXDTXAUX21
SGND Aux23
Figure 12 - RS232 Auxiliary Interface Connection
When the auxiliary interface is permanently connected as part oit is recommended to connect the cable shield to earth ground.
INSTALLATION
7/26/2019 Datalogic DS 4600 A
29/59
INSTALLATION
2.3.4 Inputs
There is an input available on the DS4600A scanner relative to th
There are also 2 general purpose inputs:
IN1 can be used to store the code verifier (see "Store verifier Help On Line).
IN2 can be used as the Reading Field Control signal which d
Code Reading Condition or the Code Resolution parameter for Refer to the WinHost Help On Line.
The pinouts are indicated below:
Pin Name Function
18 EXT TRIG+ external trigger +19 EXT TRIG- external trigger -6 IN1+ input 1 +
10 IN1- input 1 -14 IN2+ input 2 +15 IN2- input 2 -
The EXT TRIG inputs are used in the On-Line Operating mode ato scan for a code. The active state of this input is selected in sWinHost Help On Line. The yellow led, (Figure A, 7), is on whensignals the active reading phase.
These inputs are optocoupled and can be driven by both ancommand. The connections are indicated in the following diagram
18/6/14 +
USER INDS4600A
+ 5V
V
30 Vdc max.Vext
7/26/2019 Datalogic DS 4600 A
30/59
2
18/6/14 +
19/10/15 -
USER INTEDS4600A
+ 5V
VS9
25 GNDGround
V
Figure 14 - Input NPN Command Using DS4600A P
18/6/14 +
19/10/15 -
+ 5V
DS4600A USER IN
V
Grou
30 Vdc max.Vext
Figure 15 - Input PNP Command Using External Po
18/6/14 +
USER INTEDS4600A
VS9 V
+ 5V
INSTALLATION
7/26/2019 Datalogic DS 4600 A
31/59
INSTALLATION
The electrical features of the inputs are:
Maximum voltage = 30 VdcMaximum current = 25 mA.
An anti-disturbance hardware filter is implemented on the Externmilliseconds delay).
An additional 15 ms (typical) delay can be implemented through parameter (refer to WinHost Help On Line).
2.3.5 Outputs
The following pins are present on the 25-pin connector of the sca
Pin Name Function
8 OUT1+ output 1 +22 OUT1- output 1 -11 OUT2+ output 2 +12 OUT2- output 2 -
The meaning of the two outputs OUT1 and OUT2 can be defiRead, Right or Wrong). Refer to WinHost Help On Line.
By default, OUT1 is associated with the No Read event, whichcode signaled by the External Trigger is not decoded. OUT2 isRight event, which activates when the code is decoded correctly.
DS4600A USER INT
Vext
7/26/2019 Datalogic DS 4600 A
32/59
2
2.4 POSITIONING
The DS4600A scanner is able to decode moving barcode laangles, however significant angular distortion may degrade readi
When mounting the DS4600A take into consideration these threangles:Pitch 0, Skew 15 to 30 and Tilt 0.
Follow the suggestions below for the best orientation:
The Pitchangle is represented by the value P in Figure 18. Porder to minimizethe Pitchangle.
Figure 18 - Pitch Angle
The Skewangle is represented by the value S in Figure 19. Passure at least 15 for the Skewangle. This avoids the direct rlight emitted by the DS4600A.
For raster models, this angle refers to the most inclined or externall other raster lines assure more than 10 Skew.
P
INSTALLATION
7/26/2019 Datalogic DS 4600 A
33/59
INSTALLATION
The Tiltangle is represented by the value Tin Figure 20. Positioto minimizethe Tiltangle.
Figure 20 - Tilt Angle
2.5 TYPICAL LAYOUTS
The following typical layouts refer to system hardware configurathe figures refer to optional hardware configurations within the pa
These layouts also require the correct setup of the sofparameters. Complete software configuration procedures can beTo Rapid Configurationin the WinHost Help On Line.
T
2
7/26/2019 Datalogic DS 4600 A
34/59
2
2.5.1 Point-to-Point
In this layout the data is transmitted to the Host on the main sMode programming can be accomplished either through the mauxiliary interface.
The possible main interface types for the scanner are RS232 or(20 mA C.L. can also be used if the INT-24 accessory is installed
In Local Echo communication mode, data is transmitted on interface independently from the main interface selection.
When On-Line Operating mode is used, the scanner is activaTrigger (photoelectric sensor) when the object enters its reading
Main Serial InterfaceAuxiliary Serial Interface (Local Echo) (RExternal Trigger (for On-Line Mode)
Figure 21 - Point-to-Point Layout
INSTALLATION
7/26/2019 Datalogic DS 4600 A
35/59
2.5.2 Pass Through
Pass through mode allows two or more devices to be connectedserial interface.
Each DS4600A transmits the messages received by the auxiliamain interface. All messages will be passed through this chain to
When On-Line Operating mode is used, the scanner is activa
Trigger (photoelectric sensor) when the object enters its reading
The main and auxiliary ports are connected as shown in the figur
Main Serial Interface (RS232)Auxiliary Serial Interface (RS232)External Trigger (for On-Line Mode)
Figure 22 - Pass Through Layout
2
7/26/2019 Datalogic DS 4600 A
36/59
2
2.5.3 RS232 Master/Slave
The RS232 master/slave connection is used to collect data frombuild a multi-sided reading system; there can be one master connected together.
The slave scanners are connected to the main and auxiliary seslave DS4600A transmits the messages received by the auxiliamain interface. All messages will be passed through this chain to
The master scanner is connected to the Host on the main spossible main interface types for the Master scanner are RSDuplex. (20 mA C.L. can also be used if the INT-24 accessory is
Either On-Line or Serial On-Line Operating modes can be used in
When On-Line Operating mode is used, the external trigger sigsystem however it is not necessary to bring the external triggescanners.
The main and auxiliary ports are connected as shown in the figur
INSTALLATION
7/26/2019 Datalogic DS 4600 A
37/59
2.5.4 RS485 Master/Slave
The RS485 master/slave connection is used to collect data frombuild a multi-sided reading system; there can be one master connected together.
The slave scanners are connected together using RS485 halfserial interface. Every slave scanner must have a multidrop addre
The master scanner is also connected to the Host on the RS
interface.The External Trigger signal is unique to the system; there is a sand a single message from the master scanner to the Host comp
It is necessary to bring the External Trigger signal to all the scann
The main and auxiliary ports are connected as shown in the figur
A ili S i l I t f (RS232)
2
7/26/2019 Datalogic DS 4600 A
38/59
2
2.5.5 Multiplexer
Each scanner is connected to an MX4000 with the RS485 half main interface.
Main Serial Interface (RS485 Half-DupleAuxiliary Serial Interface (Local Echo) (R
External Trigger (for On-Line Mode)Figure 25 - Multiplexer Layout
The auxiliary serial interface of the slave scanners can be communication mode to control any single scanner (visualize configure it using the WinHost utility or Host Mode Programming
When On-Line Operating mode is used, the scanner is activaTrigger (photoelectric sensor) when the object enters its reading
INSTALLATION
7/26/2019 Datalogic DS 4600 A
39/59
2.6 USER INTERFACE
RS232 PC-side connections
1 5
96
9-pin male connector
14
1
25-pin male c
Pin Name Pin
2 RX 33 TX 25 GND 77 RTS 4
8 CTS 5
How To Build A Simple Interface Test Cable:
The following wiring diagrams show a simple test cable includ(push-button) trigger and PC RS232 COM port connections.
25-pin D-sub male
7
20
SGND
RXAUX
TXAUX21
DS4600A 25
13
GND
VS
9-pin
2
3
5
18
9
EXT TRIG+
VS
3
7/26/2019 Datalogic DS 4600 A
40/59
3 READING FEATURES
3.1 ADVANCED CODE RECONSTRUCTION
The traditional way of barcode reading could be called "Linear Rthe laser beam crosses the barcode symbol from its beginning toFigure 26.
Laser B
Figure 26 - Linear reading
In Advanced Code Reconstruction mode, it is no longer necbeam to cross the label from the start to the end. With just a sethe label (obtained using the motion of the label itself), the D"reconstruct" the barcode. A typical set of partial scans is shown
Code Direction
Figure 27 - Partial scans
READING FEATURES
7/26/2019 Datalogic DS 4600 A
41/59
3.1.1 Tilt Angle for Advanced Code Reconstruc
The most important parameter in Advanced Code Reconstructiomaximum tilt angle (maximum) under which the code reconstrpossible.
We define the Tilt angle as the angle () between the laser beato the barcode label, as shown in Figure 28.
Laser Beam
= tilt ang
0 to m
Figure 28 - Tilt angle
The formulas to calculate maximum depend on various paramheight, number of scans per second, code motion speed, etc. Tfor your application, please contact your Datalogic representative
You must remember that the decoder will be able to read the lbetween + max and - max as shown in Figure 29 (the shadeREAD zones).
- +
0
3
7/26/2019 Datalogic DS 4600 A
42/59
3.2 DECODING CAPACITY IN LINEAR MODE
When in Linear Reading mode, the number of reads performed btherefore the decoding capacity, is influenced by the following pa
number of scans per second
code motion speed
label dimensions
scan direction with respect to code motion
At least 5 scans during the code passage should be allowed to read.
3.2.1 Step Ladder Mode
Direction of cmovement at
Laser
DS4600A LH
READING FEATURES
7/26/2019 Datalogic DS 4600 A
43/59
If scanning is perpendicular to the direction of the code movemnumber of effective scans performed by the reader is given by th
SN = [(LH/LS) *SS] - 2
These symbols signify:
SN = number of effective scansLH = label height (in mm)LS = label movement speed (in mm/s)
SS = number of scans per second
For example, the DS4600A (800 scans/sec.), for a 25 mm high cmm/s performs:
[(25/1250) *800] - 2 = 14 effective scans.
3.2.2 Picket Fence Mode
Direction of comovement at
LaDS4600A
FW
LW
3
7/26/2019 Datalogic DS 4600 A
44/59
If scanning is parallel to the code movement (Figure 31) the scans is given by:
SN = [((FW-LW)/LS) *SS] - 2
These symbols signify:
SN = number of effective scansFW = reading field width (in mm)LW = label width (in mm)
LS = label movement speed (in mm/s)SS = scans per second
For example, for a 100 mm wide code moving in a point where200 mm wide at a 2000 mm/s speed, the DS4600A (800 scans p
[((200-100)/2000) *800] - 2 = 38 scans
3.3 PERFORMANCE
The DS4600A scanner is available in different versions accoperformance.
Version Max Code Resolution Speed
mm (mils) scans/s
21XX / 31XX 0.50 (20) 800
20XX / 30XX 0.25 (10) 800
220X / 32XX 0.20 (8) 800
Version Reading Distance
READING FEATURES
7/26/2019 Datalogic DS 4600 A
45/59
The reading characteristics for the raster versions are given in distance between the top and bottom scan lines is given
distances measured from the laser beam output window.
Reading Distance
Version 150 mm
(5.9 in)
500 mm
(20 in)
2X1X (R1) 7.5 mm
(0.30 in)
24 mm
(0.94 in)
2X2X (R2) 16 mm
(0.62 in)
45 mm
(1.77 in)
Refer to the diagrams given in paragraph 3.4 for further defeatures. These diagrams are taken on various resolution sampambient temperature, depending on the conditions in the notes u
If standard devices do not satisfy specific requirements, coDatalogic distributor, supplying code samples, to obtain comple
reading possibilities.
3
7/26/2019 Datalogic DS 4600 A
46/59
3.4 READING DIAGRAMS
The following diagrams show the reading distance for barcdensities.
DS4600A-210X (Long Range)
4
4
12
12
16
(in)
0 4 20128 16
0 100 200 300 400 500 600 700 800 900
400
300
200
100
0
100
200
300
400
(mm)
24 28 32 36
16
8
8
0.50 mm (20 mils)0.60 mm (24 mils)0.80 mm (31 mils)1.00 mm (40 mils)
NOTE: (0,0) is the center of the laser beam output window
CONDITIONS:
READING FEATURES
7/26/2019 Datalogic DS 4600 A
47/59
DS4600A-200X (Medium Range)
4
2
0
2
10
8
6
4
6
(in)
0 2 64 128 10 14 16 18
0 50 100 150 200 250 300 350 400 450 50
250
200
150
100
50
0
50
100
150
200
250
(mm)
2
0.25 mm(10 mils)
0.30 mm(12 mils)
8
10
NOTE: (0,0) is the center of the laser beam output window
CONDITIONS:
Test Codes used = Interleaved 2/5 and Code 39
3
7/26/2019 Datalogic DS 4600 A
48/59
DS4600A-22XX (Short Range)
2
1
0
1
5
4
3
2
3
4
5
(in)
0 1 32 64 5 7 8 9
0 20 40 60 80 100 120 140 160 180 200 220 2
120
100
80
60
40
20
0
20
40
60
80
100
120
(mm)
0.20 mm(8 mils)
0.30 m(12 mi
NOTE: (0,0) is the center of the laser beam output window
CONDITIONS
Code = Interleaved 2/5 or Code 39
READING FEATURES
7/26/2019 Datalogic DS 4600 A
49/59
DS4600A-22XX (Short Range)
4
2
0
2
10
8
6
4
6
8
10
(in)
0 2 64 128 10 14 16
0 40 80 120 160 200 240 280 320 360 400 44
240
200
160
120
80
40
0
40
80
120
160
200
240
(mm)
0.50 mm(20 mils)
NOTE: (0,0) is the center of the laser beam output window
CONDITIONS
Test Codes used = Interleaved 2/5 and Code 39
3
7/26/2019 Datalogic DS 4600 A
50/59
DS4600A-2X1X (Raster R1)
4
2
0
2
10
8
6
4
6
(in)
0 2 64 128 10 14 16 18
0 50 100 150 200 250 300 350 400 450 50
250
200
150
100
50
0
50
100
150
200
250
(mm)
20
0.25 mm(10 mils)
0.30 mm(12 mils)
8
10
NOTE: (0,0) is the center of the laser beam output window
CONDITIONS:
Test Codes used = Interleaved 2/5 and Code 39
"Pitch" angle = 0
"Sk " l 18
READING FEATURES
7/26/2019 Datalogic DS 4600 A
51/59
DS4600A-2X2X (Raster R2)
4
2
0
2
10
8
6
4
6
(in)
0 2 64 128 10 14 16 18
0 50 100 150 200 250 300 350 400 450 50
250
200
150
100
50
0
50
100
150
200
250
(mm)
20
0.25 mm(10 mils)
0.30 mm(12 mils)
8
10
NOTE: (0,0) is the center of the laser beam output window
CONDITIONS:
Test Codes used = Interleaved 2/5 and Code 39
"Pitch" angle = 0
"Sk " l 18
3
7/26/2019 Datalogic DS 4600 A
52/59
DS4600A-31XX (Long Range)
4
4
12
12
16
(in)
0 4 20128 16
0 100 200 300 400 500 600 700 800 900
400
300
200
100
0
100
200
300
400
(mm)
24 28 32 36
16
8
8
0.50 mm (20 mils)0.60 mm (24 mils)0.80 mm (31 mils)
1.00 mm (40 mils)
NOTE: (0,0) is the center of the laser beam output window
CONDITIONS:
Test Codes used = Interleaved 2/5 and Code 39"Pitch" angle = 0
"Skew" angle = 15
"Tilt" angle = 0
READING FEATURES
7/26/2019 Datalogic DS 4600 A
53/59
DS4600A-30XX(Medium Range)
4
2
0
2
10
8
6
4
6
(in)
0 2 64 128 10 14 16 18
0 50 100 150 200 250 300 350 400 450 50
250
200
150
100
50
0
50
100
150
200
250
(mm)
2
0.25 mm(10 mils)
0.30 mm(12 mils)
8
10
NOTE: (0,0) is the center of the laser beam output window
CONDITIONS:
Test Codes used = Interleaved 2/5 and Code 39
3
7/26/2019 Datalogic DS 4600 A
54/59
DS4600A-32XX (Short Range)
4
2
0
2
10
8
6
4
6
8
10
(in)
0 2 64 128 10 14 16
0 40 80 120 160 200 240 280 320 360 400 44
240
200
160
120
80
40
0
40
80
120
160
200
240
(mm)
0.20 mm(8 mils)
NOTE: (0,0) is the center of the laser beam output window
CONDITIONS
Test Codes used = Interleaved 2/5 and Code 39
MAINTENANCE
7/26/2019 Datalogic DS 4600 A
55/59
4 MAINTENANCE
4.1 CLEANING
Clean the laser beam output window periodically for continued the reader.
Dust, dirt, etc. on the window may alter the reading performance
Repeat the operation frequently in particularly dirty environments
Use soft material and alcohol to clean the window and substances.
WARNING
Clean the window of the DS4600A when the scaor, at least when the laser beam is deactivated.
5
7/26/2019 Datalogic DS 4600 A
56/59
5 TECHNICAL FEATURES
ELECTRICAL FEATURES DS4600A-XXX0
Power
Supply Voltage 10 to 30 Vdc
Power Consumption max. 6 W
Serial InterfacesMain RS232, RS485 full-duplex, R
(20 mA C.L. only with INT
Auxiliary RS232
Baudrates 1200 to 1152
Inputs External Trigger, I
(optocoupled NPN Voltage max. 30 Vdc
Input Current max. 25 mA
Outputs User-defined OUT1 a(optocoupled open emitter
VCE max. 40 Vdc
Collector Current max. 40 mA continuous; 130VCEsaturation 1V at 10 mA m
Power Dissipation max. 90 mW at 40 C (Amb
OPTICAL FEATURES
Light Source Semiconductor las
Wavelength (Note 1) 630 ~ 680 nSafety Class Class 2 EN60825-
READING FEATURES (Note 2) 200X / 300X 210X / 310X
Aperture Angle 66 70
TECHNICAL FEATURES
7/26/2019 Datalogic DS 4600 A
57/59
SOFTWARE FEATURES
READABLE CODE SYMBOLOGIES
EAN/UPC Code 93
2/5 Interleaved Code 128
Code 39 EAN 128
Codabar Pharmacode
Code Selection up to six codes during one
Decoding Safety can enable multiple good Headers and Terminators up to four headers and fou
Operating Modes ON LINE, AUTOMATIC, SERIA
Configuration Modes through menus using W
receiving commands fports (HOST MODE)
Parameter Storage Non-volatile internal mem
ENVIRONMENTAL FEATURES DS4600A-2XX0
Operating temperature (Note 3) 0 to 40 C
(32 to 104 F)
Storage temperature -20 to 70 C (-4
Humidity max. 90% non conVibration resistance IEC 68-2-6 test
10 to 55 Hz; 2 hour
Shock resistance IEC 68-2-27 tes
11 ms; 3 shocks o
Protection class IP65
PHYSICAL FEATURESMechanical dimensions 101 x 83.5 x 42 mm (3.97
Weight about 615 g. (22 oz.)
7/26/2019 Datalogic DS 4600 A
58/59
DATALOGIC S.p.A.,
Via Candini, 240012 - Lippo di Calderara
Bologna - Italy
dichiara chedeclares that thedclare que lebescheinigt, da das Gertdeclare que el
DS4600A-XXXX Laser Scanner e tutti i suoi modelli
and all its modelset tous ses modlesund seine modelley todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:are in conformity with the requirements of the European Council Directives listed below:sont conformes aux spcifications des Directives de l'Union Europenne ci-dessous:der nachstehend angefhrten Direktiven des Europischen Rats:cumple con los requisitos de las Directivas del Consejo Europeo, segn la lista siguiente:
89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti suand further amendmeet ses successifs aund spteren Abndey succesivas enmi
Basate sulle legislazioni degli Stati membri in relazione alla compatibilit elettromagnetica ed allaOn the approximation of the laws of Member States relating to electromagnetic compatibility and Base sur la lgislation des Etates membres relative la compatibilit lectromagntique et la ber die Annherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Vertrentsprechen.
Basado en la aproximacin de las leyes de los Pases Miembros respecto a la compatibilidad ede seguridad relativas al producto.
Questa dichiarazione basata sulla conformit dei prodotti alle norme seguenti:This declaration is based upon compliance of the products to the following standards:Cette dclaration repose sur la conformit des produits aux normes suivantes:Diese Erklrung basiert darauf, da das Produkt den folgenden Normen entspricht:Esta declaracin se basa en el cumplimiento de los productos con las siguientes normas:
EN 55022, August 1994: LIMITS AND METHODS OF MEASUREMENTS OF RADIO DISTINFORMATION TECHNOLOGY EQUIPMENT (ITE)
EN 61000-6-2, April 1999: ELECTROMAGNETIC COMPATIBILITY (EMC).PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRI
7/26/2019 Datalogic DS 4600 A
59/59