Embed Size (px)
Citation preview
DEPARTMENT OF MECHANICAL ENIGINEERING,
UNIVERSITY OF ENGINEERING & TECHNOLOGY LAHORE (KSK CAMPUS).
Lab Incharge
1. Capt. (R) I A Hashmi
2. Mr. Rizwan Awan
Coordination Staff:
Mr.Mohsin Awan (Lab Attendant)
Apparatuses Detail
1. 4 STROKE DIESEL ENGINE MODEL
2. Experimental Impulse Turbine
3. Experimental Reaction Turbine
4. Two Stage Compressor Test Unit
5. Nozzle Pressure Distribution Unit
6. Transparent combustion Engine
7. Combustion Laboratory Unit
8. 4 Stroke Diesel Engine
9. 4 Stroke Petrol Engine
10. Electric Dynamometer and Generator
11. Dead weight Calibrator
12. 4 Stroke Petrol Engine Model
13. ABS Braking System
14. Disc Baking System
15. Power Steering
16. Fuel Injection Pump
17. Door
18. Door
19. White Board
20. Notice Board
21. Chairs
22. Teacher Table
23. Black Board
1. 4 SROKE DIESEL ENGINE DEMONSTRATION UNIT
2. EXPERIMENTAL REACTION TURBINE
Objectives:-
1. To Study and Identification of
the different parts.
2. To observe How Diesel Engine
Woks.
3. To Study of fuel cycling and
combustion process.
Objectives:-
1. To Investigate of torque/ speed
and power /speed
characteristics of a single stage
reaction turbine.
2. To Observe the first law of
Thermodynamics to a simple open
system under going a steady flow
process.
3. ToDetermine of the isentropic
efficiency of a turbine.
4. construction of retardation
curve and from this the
determination of the effect of
resistances due to mechanical and
fluid friction.
Objectives
1.To Study and Identify
the different parts.
2. To Observe the Working
of Diesel engine.
3. To Demonstrate the fuel
cycling and combustion
process.
Objectives
1. To Investigate the
torque/ speed and power
/speed
Characteristics of a single
stage reaction turbine.
2. To observe the first law
of Thermodynamics to a
simple open system
undergoing a steady flow
process.
3. To Determine of the
isentropic efficiency of a
turbine.
4. The construction of
retardation curve and
from this the
determination of the
effect of resistances due to
mechanical and fluid
friction.
3. EXPERIMENTAL IMPULSE TURBINE
4. 2 STAGE AIR COMPRESSOR
Objectives
1. To Investigate the torque/
speed and power /speed
Characteristics of a single stage
reaction turbine.
2. To observe the first law of
Thermodynamics to a simple open
system under going a steady flow
process.
3. To Determine the isentropic
efficiency of a turbine.
4. The construction of retardation
curve and from this the
determination of the effect of
resistances due to mechanical and
fluid friction.
Objectives
1. To Investigate the variation in
air flow rate, with compressor
pressure ratio:- With and without
intercooling
2. To Investigate the variation in
volumetric efficiency with
compressor pressure ratio:- With
and without intercooling
3. To Investigate the variation of
isothermal efficiency with
compressor pressure ratio:- With
and without intercooling
4. To Investigate the compressor
performance relative to electrical
power:- With and without
intercooling
5. To study the operation of the
compressor of as a single stage
device.
5. NOZZLE PRESSURE DISTRIBUTION UNIT
Objective
Analysis Nozzle pressure
distribution.
8. 4-STROKE DIESEL ENGINE(1600CC)
9. 4-STROKE PETROL ENGINE(1600CC)
Objectives:-
Prove that
Pressure = Force / Area
Objectives:-
1. To Study and Identification of
the different parts of engine.
2. To observe the Working of the
engine.
3. To observe the fuel cycling and
combustion process in Engine.
[Type sidebar content. A sidebar is
a standalone supplement to the
main document. It is often aligned
on the left or right of the page, or
located at the top or bottom. Use
the Text Box Tools tab to change
the formatting of the sidebar text
box.
Type sidebar content. A sidebar is
a standalone supplement to the
main document. It is often aligned
on the left or right of the page, or
located at the top or bottom. Use
the Text Box Tools tab to change
the formatting of the sidebar text
box.]
Objectives:-
1. To Identify the parts and
manual operation of the
Megatech Mark III engine.
2.To Examine the 4 strokes of the
Megatech Mark III Engine.
3. To Operate the Engine with
Variable Timing.
4. To Observe the working of
Carburetor and Fuel Controls.
5. To Operate the Megatech Mark
III Engine with Different Fuels.
Objectives:-
1. To Investigate of turndown
ratio and firing rate
2. To Investigate of air/fuel ratio
and stoichiometeric condition
3. To Compare the practical and
theoratical flue gas analysis
4. To Compare the two liquid fuels
5. To Compare the two gaseous
fuels
6. Heat Balance
7. Energy Balance
8. Temperature Measurment
Experiments
Objectives
1. To Study and identify
the different parts.
2. To Observe the Working
of demonstration of
engine.
3. To Demonstrate of fuel
cycling and combustion
process.
Objective
1.To Study and Identify
the different parts.
2. To Observe the Working
of demonstration of
engine.
3. To Demonstrate of fuel
cycling and combustion
process.
11. DEAD WEIGHT CALLIBRATOR
12. 4-STROKE PETROL ENGINE DEMONTRATION UNIT
[Type sidebar content. A sidebar is
a standalone supplement to the
main document. It is often aligned
on the left or right of the page, or
located at the top or bottom. Use
the Text Box Tools tab to change
the formatting of the sidebar text
box.
Type sidebar content. A sidebar is
a standalone supplement to the
main document. It is often aligned
on the left or right of the page, or
located at the top or bottom. Use
the Text Box Tools tab to change
the formatting of the sidebar text
box.]
Objective
To observe the
measurement of pressure
with externally applied
force.
To study the working
processes of a four stroke
petrol engine
13. ABS BRAKING SYSTEM
14. HAND BRAKE
Objectives:-
To Study of ABS(Automatic
Braking System) and Its
Working
Objectives:-
To Study of Disc Operating
System and Its Working
15. POWER STEERING
16. FUEL INJECTION PUMP
Objectives:-
To Study Power Steering
Objectives:-
To Study the working of
fuel injection pump
