Digital Menu Board Ceiling Mount Installation Instructions · 2019. 9. 12. · Digital Menu Board 4249 Ceiling Mount Installation Manual Page 11 ... The Monitor Security Locks (Part

www.microndisplaysolutions.com

Digital Menu Board Ceiling Mount

Installation Instructions

M2T4249C M3T4249C

Digital Menu Board 4249 Ceiling Mount Installation Manual Page 2 Rev. 04/19

Table of Contents

Important Safety Instructions............................................................................................................................. 3

Models and Specifications .................................................................................................................................. 4

Configuration and Drawings .............................................................................................................................. 5

Package Contents .............................................................................................................................................. 6

Step 1 – Using a Two (2) Wide or Three (3) Wide Mount Only ....................................................................... 7

Step 2A – Joining 2W and 3W Menu Board Mounts to make a 4W or Greater Mount (42” & 43”) .................. 8

Step 2B – Joining 2W and 3W Menu Board Mounts to make a 5W or Greater Mount (46”+) .......................... 9

Step 3 – Mounting to Ceiling ......................................................................................................................... 10

Step 4 – Tilt Mechanism Adjustment ............................................................................................................ 10

Step 5 – Attaching End Caps .......................................................................................................................... 10

Step 6 – Attaching VESA Panel Brackets & Mounting Monitors .................................................................... 11

Step 7 – Installing Monitor Security Locks (Optional Item) ........................................................................... 12

Step 8 – Installing Cable Tie Clamps (Optional Item) ..................................................................................... 12

Warranty ........................................................................................................................................................... 13


Important Safety Instructions

Use the following safety guidelines to help protect you during the installation, especially with installing the video panels to mount and when access to panels is required to ensure your own personal safety.

• Read all the installation instructions before installing the mounting solution.

• Read and follow all important safety instructions.

• Depending on size of mount, two (2) persons may be required for installation.

• Please ensure all safety precautions are followed when working with heights.

CAUTION: Before you begin any of the installation procedures read and follow the warnings and important safety instructions within the manual.

WARNING!

FAILURE TO FOLLOW INSTRUCTIONS ON ACCESSING BEHIND PANELS AND SERVICING PANELS MAY RESULT IN POSSIBLE PERSONAL INJURY AND DAMAGE TO VIDEO PANELS DUE FROM FALLING!

BEFORE INSTALLING THE MOUNT, ENSURE THE CEILING IS STRUCTUALLY SOUND AND ABLE TO PROPERLY SUPPORT THE COMBINED WEIGHT OF MOUNT AND VIDEO PANELS!

Cat No. M2T4249C and M3T4249C

Tested and Evaluated to CSA Model Code SPE-1000, Clause 6.2.8. Testé et évalué selon le code de modèle CSA SPE-1000, article 6.2.8

Warning: Maximum hanging load 100 Kg for M2T4249C and 120 Kg for M3T4249C. Attention: Charge maximale suspendue 100 Kg pour M2T4249C et 120 Kg pour M3T4249C.


Models and Specifications

Product M2T4249C M3T4249C

Type 2 Wide Tilt Menu Board 3 Wide Tilt Menu Board

Screen Sizes 42” to 49”

Tilt 0 to 15 Degrees

Vesa 200 to 400

Security Locks Included

Weight Load 100 kg 120 kg

Dimensions (WxHxD)

With 00 Tilt 1800 x 240 x 100mm 2750 x 240 x 100

Dimensions (WxHxD)

With 150 Tilt 1800 x 240 x 150mm 2750 x 240 x 150mm

Note:

• For 42” to 43” screens sizes, the use of Joiner Rail Assembly not required.

• For greater than 43” screen sizes when joining Digital Menu Board mounts together to make overall 4 wide or larger mount please add 400mm at each joining point to arrive at overall length.


Configuration

M2T4249C

M3T4249C


Package Contents Description Model Qty Picture

Preassembled Mount P/N# MD4249CF 2T4249C 1

Part A

Preassembled Mount P/N# MD4249CL (Left) P/N# MD4249CR (Right)

3T4249C 2

Part A

Joiner Rail Assembly – Small (provided if 2 more mounts ordered) P/N# MD4517JR

2T4249C 3T4249C 2

Part JRS

Joiner Rail Assembly – Large (provided if 2 or more mounts ordered) P/N# MD4590JR

2T4249C 3T4249C 1

Part JRL

Panel VESA Bracket P/N# VBM4249

2T4249C 4

Part B

3T4249C 6

End Cap – Small (May be already installed) P/N# MD1044

2T4249C 3T4249C 4

Part ECS

End Cap – Large (May be already installed) P/N# MD1009

2T4249C 3T4249C 2

Part ECL

Hardware P/N# MD4249H

2T4249C 2

Part H 3T4249C 3

Cable Tie Clamp P/N# MD1006

2T4249C 3

Part CC 3T4249C 3

Security Lock P/N# MD1026

2T4249C 2

Part SL

3T4249C 3


Step 1 – Using a 2 Wide or 3 Wide Mount Only Instructions Diagrams For a two (2) wide mount proceed to Step 3.

Fig. 1A

For a three (3) wide mount the left and right sections need to be joined together using the four (4) joiner bars supplied. See figure 1B. Once they are joined together, tighten screws using 4mm hex wrench. See figure 1C, and 1D.

Fig. 1B

Fig. 1C Fig. 1D


Step 2A – Joining 2W & 3W Mounts to make a 4W or > (For 42” & 43”) Mount Type Instructions Diagrams For configurations requiring 4W or 6W. • Join a 2W+2W menu

board mount by using the Joiner Bars removed from Joiner Rail Assemblies provided (Part JRS and JRL). See fig.2A, 2B.

• Place Joiner Bars as shown in fig. 2C.

• Tighten screws using 4mm hex wrench once they are in place. See fig. 2D and 2E.

• If required, reposition pipe flanges to desired position.

Fig. 2A Fig. 2B

Fig. 2C

Fig. 2D Fig. 2E

For configurations requiring 5W. • Join a 2W+3W menu


• Place Joiner Bars as shown in fig. 2F.

• Tighten screws using 4mm hex wrench once they are in place. See fig. 2D, and 2E.

• If required, reposition pipe flanges.

Fig. 2F

For configurations requiring 6W. • Join a 3W+3W menu


• Place Joiner Bars as shown in fig. 2G.



Fig. 2G


Step 2B – Joining 2W & 3W Mounts to make a 4W or > (46”+) Mount Type Instructions Diagrams For configurations requiring 4 wide or 6 wide menu boards. • Join a 2W+2W menu

board mount using both Joiner Rail Assemblies provided (Part JRS and JRL). See fig.2A, 2B, 2C.

• Tighten screws using 4mm hex wrench once they are in place. See fig. 2D and 2E.

• If required, reposition pipe flanges to desired position.

Fig. 2A Fig. 2B

Fig. 2C

Fig. 2D Fig. 2E

For configurations requiring 5 wide menu boards. • Join a 2W+3W menu

board mount using both Joiner Rail Assemblies provided (Part JRS and JRL). See fig.2A, 2B, and 2F.



Fig. 2F

For configurations requiring 6 wide menu boards. • Join a 3W+3W menu

board mount using both Joiner Rail Assemblies provided (Part JRS and JRL). See fig.2A, 2B, and 2G.



Fig. 2G


Step 3 –Mounting to Ceiling Instructions Diagrams Attach menu board mount to ceiling structure using threaded pipe.

Step 4 –Tilt Mechanism Adjustment

Instructions Diagrams For a 2 wide mount there is a tilt adjustment mechanism at each end. For a 3 wide mount there are four (4) tilt adjustment mechanisms. The maximum tilt angle is 15 Degrees. • To set desired tilt angle, loosen the tilt

adjustment screws using a 4mm Allen wrench.

• Once you have the desired tilt angle

tighten the tilt adjustment screws.

Fig. 4A

Step 5 – Attaching End Caps Instructions Diagrams • Install the small Black End Caps (if not

already installed) on both ends of mount. See figure 5A, and 5B.

• Use clear silicone (optional) to affix End

Caps.

• Install large End Caps (if not already installed) on both ends as shown in fig. 5A, and 5C by tapping into place.

Fig. 5A Fig. 5B Fig. 5C

Tilt adjustment screw

Tilt safety screw.

DO NOT ADJUST

Small End Cap

Large End Cap


Step 6 –Attaching VESA Panel Brackets & Mounting Monitors Instructions Diagrams • Remove monitors to be installed from

their cartons and attach the Panel VESA Brackets (Part B) to back of monitors at the VESA mounts as shown in figure 6A. Mounting hardware is provided (Part F).

• The mounting hardware consists of

various lengths of M6 and M8 screws to accommodate different manufacturer specifications.

• If M6 size screws are required, you will

need to use the white M8 reducer sleeves provided. See figure 6B and 6C.

IMPORTANT The video connections and placement of AC plug will vary by model and brand. In the event any of the cabling is in line with the Panel VESA Bracket and interferes, the use of shims/plastic spacers will be required to extend VESA Panel Bracket outwards.

Fig. 6A

Fig. 6B Fig. 6C

• Lift each monitor and position so the upper and lower clamps on each VESA Panel Bracket slide into the t-slot of the frame assembly. See figure 6D.

• Gently slide monitor into desired

position along frame assembly.

• Repeat for each monitor.

Fig. 6D

If you still need assistance with the installation, we are a phone call away at (905)-828-1662.


Step 7 – Installing Monitor Security Locks (Optional Item) Instructions Diagrams The Monitor Security Locks (Part SL) are used to secure monitor to Top Rail. • Place one (1) Monitor Security Lock on

either the left or right Top Panel Clamp for each monitor. See Figure 7A.

• Once the Monitor Security Lock has

been positioned directly on top of panel clamp, secure the lock by tightening the two (2) screws. See Figure 7B.

Fig. 7A

Fig. 7B

Step 8 – Installing Cable Tie Clamps (Optional Item)

Instructions Diagrams The Cable Tie Clamps are used for cable management and/or to fasten media player to frame assembly, etc. • Insert Cable Tie Clamps where desired

into t-slot and then rotate the Cable Tie Clamp 900 to secure in place.

• Thread cable tie thru the Cable Tie

Clamp as required.

Fig. 8A Fig. 8B


Warranty Micron Display Solutions (“MICRON”) warrants to the first purchaser for this product (“Product”), when shipped in its original container and sold or distributed in Canada by Micron or by an authorized Micron dealer, and Product was not sold “as is” or “sales final” that the Product will be free from defects in material and workmanship for a period of three (3) years and will within the warranty period, either repair the defective Product or provide the purchaser a replacement of the defective Product.

This warranty does not apply to any appearance items of the product nor to the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, which has been altered or modified in design or construction, or if the serial number or model number affixed to Product has been removed, defaced, changed, altered or tampered with.

Micron Display Solutions 2679 Bristol Circle, Unit 6

Oakville, Ontario L6H 6Z8

(905)-828-1662 www.microndisplaysolutions.com

http://www.microndisplaysolutions.com/

Documents

Digital Menu Board Ceiling Mount Installation Instructions · 2019. 9. 12. · Digital Menu Board 4249 Ceiling Mount Installation Manual Page 11 ... The Monitor Security Locks (Part