DIGI*TRACModel 2 ControllerIdentiv DIGI*TRAC controllers are “standalone” access control systems that support:— ScramblePad and ScrambleProx secure keypads

® ®

— MATCH intelligent reader interfaces™

— High-security alarm monitoring— Relay control outputsWhen connected locally by a LAN or by telephonelines to an Identiv Host PC or server, DIGI*TRAC controllers provide a high-integrity enterprise-wide access control and security management solution.

FeaturesControls two fully-supervised doors and two unsupervised doors– Both Entry and Exit – Keypads and/or ReadersModular: Uses Expansion BoardsStandalone or Networked– Microprocessor Based– High Security Supervised Alarm

Inputs (2% Supervision)– Door Relay Outputs– General Purpose Relay Outputs– Dedicated Alarm Relay Output– Digital Keypad/Reader ChannelDigital Transmission– Long Wiring Runs– Multi-drop Connections– LAN Interface Options– Modem OptionsEncryption Algorithm– High-Security TransmissionLocal or Remote Programming – ScramblePad, ScrambleProx

or PC

extensive local �rmware for controlsequences as basic as “who goeswhere and when” to sophisticated functions like two-person rule, occupancycounting, individual user tagging, doorinterlocking, and anti-passback.

Access may be restricted based on:Time of Day, Day of Week, andDoor. Access may be granted whenthe user presents the correct code,card, or both. The user may be grant-ed “temporary” access based on: Use Count Limits, Temporary Day Limits,and Absentee Rule Limits, with Auto-Disable or Auto-Delete on expirationof Temporary Users.

Additional functions include:Unlock/Relock, Alarm Mask/Unmask,and Lock Down/Lock Down Release.

The associated door may be monitoredfor: Door Forced Open and Door OpenToo Long, while providing Auto Re-Lock control.

Downloadable Firmware– Flash MemoryPrinter PortMultiple Reader TechnologiesResident Application LibraryUL Listed: 294, 1076, Grade AA

DescriptionAll DIGI*TRAC controllers have thesame �rmware functionality. A rangeof models and expansion options pro-vides a variety of access control, high-security alarm monitoring, relay con-trol outputs, and programmable logiccon�gurations to �t most applica-tions. Each unit can be a completestandalone system or a distributedcontroller in a larger, multi-site enter-prise system. This modular designand scalable architecture allows asystem to start small and grow large.

Access Control SystemAs an access control system, theDIGI*TRAC controller includes

™

DATA SHEET

DATA SHEET

Readers supported include ScramblePad,ScrambleProx and, via the MATCHintelligent reader interface, these tech-nologies: Magnetic Stripe, Proximity,Wiegand, Bar Code, Smart Card, RF, IR,and Biometric. Technologies may becombined on the same controller or thesame door in any combination.

High Security Reader ChannelThe DIGI*TRAC controller supportselectrically isolated terminal blocks thatprovide communications and power tothe ScramblePad, ScrambleProx andMATCH interfaces. The communicationpath allows multi-drop connections forentrance and exit keypads and dual tech-nology applications.

User codes are digitized for transmissionbetween a Identiv ScramblePad,ScrambleProx or MATCH and theDIGI*TRAC controller. Digital trans-mission allows longer wiring runs thanare normally available with conventionalaccess control reader technologies.

High Security Alarm MonitoringIdentiv uses very stable digitallyprocessed analog inputs with 2% linesupervision for high security alarmmonitoring. A line supervision module(DTLM, MELM, or SBMS) is locatedat the door contact, alarm sensor,

request to exit (RQE), or similar deviceto establish this supervision.

In lieu of “shunting”, which turns offsupervision, Identiv uses alarm maskingfor full-time supervision and reportingof line status — even during hours ofauthorized access. Conditions reportedinclude: Alarm, Secure, RQE, Mask,Tamper Alarm, Tamper Secure, Short,Open, Noisy, and Input Out-of-Spec.

Relay Control SystemRelay outputs on DIGI*TRAC con-trollers can be used for: electric doorlocks and strikes, arming/disarmingsecurity systems, alarm annunciation,elevator �oor control, HVAC control,lighting control, storage locker control,and many other equipment control appli-cations. These relays may be activatedby codes (via ScramblePad), cards (via MATCH and reader), time zones,alarms, or logic sequences linked toother relays.

When used with a ScramblePadDIGI*TRAC controllers are ideal forafter-hours tenant override systems. Ahistory of who issued the override com-mand is available for tenant billing oraudit trails. The same ScramblePadused for access control can be used fortenant override and remote operatorcommand functions.

Programmer’s TerminalDIGI*TRAC controllers can be pro-grammed by either a ScramblePad or aPC using Identiv Host software. ThePC can be local or connected by LANor modem. A ScramblePad used foraccess control can also be used as apassword protected programmer’s ter-minal. Programming functions sup-ported include: add and delete useraccess codes, assign unlock/relockcodes, assign alarm codes, and assignelevator control codes.

SCRAMBLE*NET™

DIGI*TRAC controllers communicatewith an Identiv Host PC using SCRAM-BLE*NET protocol which uses anencryption algorithm for high security.The SCRAMBLE*NET command/packet structure is ideal for LAN andhardwired paths, including RS-485multi-drop and RS-232 via direct con-nect or dial-up modem.

Reliability By DesignDIGI*TRAC controllers are designed for“high availability” as complete systemssolutions for global markets. Standby batteries for both memory and system operation are standard. The controller ships with an internal internationalpower supply. All door relays are socketed.

SNIB

MEB

AEB8

REB8

MEMORYBATTERYBACKUP

EXPANSIONBOARD(S)

MEDECOLOCK

KEYPAD CIRCUITFUSES

FUSEDPOWERSUPPLY

COMMANDCONTROLMODULE (CCM)

STANDBYBATTERY

TYPICAL DOORTERMINAL BLOCK

HEAVY DUTYDOOR RELAYS

RELAY STATUSLEDS

DEDICATEDALARM RELAY

DIAGNOSTICLEDS

PARALLELPRINTER PORT

TAMPERSWITCH

DATA SHEET

All Keypad/Reader terminals and power circuits are fused. Each unit iscon�gured in a heavy duty, NEMA-styleenclosure, with a high security lock andtamper alarm.

Speci�cationsCommunications

Serial Interface Ports:– SCRAMBLE*NET: Requires SNIB

Encrypted message structure – RS-485 multi-drop or RS-232

protocol– Optically isolated serial port– Baud Rate: 9600 or 19,200– RS-485: 4000 ft (1220 m) with 22

gauge; two pair, stranded, twisted, overall shield or 19,200

– RS232: 50 ft (15 m) at 9600 baud

Parallel Printer Port: StandardKeypad/Reader Port:16 device address– Address 1-4 for door relay 1-4

entry; addresses 9-12 for door relay 1-4 exit; any address for command and programming

– Wiring: 750 ft (160 m) with 22 gauge, 1800 ft (550 m) with 18 gauge; two pair, stranded, twisted, overall shield

FirmwareCommand and Control Module (CCM):– Removable and Upgradable– Time Zones: 150– Access Zones: 128– Control Zones: 256– Holidays: Four 366 Day x 2 years– Daylight Savings Time AdjustmentDial-Up to Remote Host:– Phone Numbers: four with roll-over– User selectable retry attempts– Call-back mode for security– Initiation by alarm, buffer

% full, and/or time

MemoryBuffers: 1500 events, 1500 alarms standard–20,000 events, 2,000 alarms withMEB/BE

– 20,000 events, 2,000 alarms with MEB/CB (reduces users by 20%)

– Oldest discarded �rst, if fullUsers: 4000 standard– 8,000 with MEB/CE16– 20,000 with MEB/CE32– 68,000 with MEB/CB64– 132,000 with MEB/CB128Battery Backup: 30 day for code, setups, clock and buffer

ElectricalKeypad/Reader Power: two terminals– 1.0 Amp at 24VDC each, fused– 1.05 Amp at 24VDC total– Powers ScramblePad, ScrambleProx

and MATCHPrimary and Standby Power:– 90-130VAC, 50/60 Hz, fused– 180-260VAC, 50/60 Hz, fusedUninterruptible Power SupplyStandby Batteries: 1.3 AH IncludedDoor Relays: 10 Amp, Form C Control Relays: 2 Amp, Form C (requires REB8)Alarm Relays: 2 Amp, Form C LEDs:– Individual Relay Status– Battery (OK, Low, Fail)– AC (OK, Fail) – System (OK, Fail)– Keypad/MATCH (Poll, Response)– SCRAMBLE*NET (Poll, Response)– Test Mode– Alarm Events in Buffer– Box Tamper Alarm

PhysicalDoor Tamper SwitchMedeco High Security Key LockEnclosure: NEMA-type, with conduitknockouts and removable doorDimensions: 18 x 15.25 x 5.5 in (45.7 x 38.7 x 14 cm)Expansion Boards: 6 x 4.25 x .75 in(15.2 x 10.8 x 1.9 cm)Shipping Weight: 30 lbs (13.6 kg)Expansion Boards: 1 lb (0.5 kg)Operating Temperature Range: 32° to 140° F (0° to 60° C)Relative Humidity: 0 to 90%, non-condensing

Listings and ApprovalsUL 294 Access Control Systems UnitsUL 1076 Proprietary Burglar Alarm Systems, Grade AACE

DTLM2

EXIT

MOV

SCRAMBLEPAD SCRAMBLEPROX

OR MATCH

PSLED

FUSE

SOCKETEDDOOR RELAY

TYPICAL DOORTERMINAL BLOCK

G + A B S

G+ABS

NO C NC HI LO S

DIG

I*TR

AC

Typical Controller-to-Door Wiring Diagram

DATA SHEET

Ordering Information –– Controller

M2N DIGI*TRAC MODEL 2N - 2 Door - 115VAC

Controls two supervised doors and two unsupervised doors. 4000 users.Includes four door relays, two alarm inputs (requires line modules)enclosure, power supply, battery, tamper switch, Medeco lock,and SNIB. Supports expansion boards. UL Listed. CE. 115 VAC.

AEB8

REB8

MEB/BE

MEB/CE16

MEB/CB64

MEB/CB128

DM9600A-DL

Alarm Expansion Board - 8 Inputs

Relay Expansion Board - 8 Relays

Memory Expansion Board - BufferExpansion

Memory Expansion Board - CODEExpansion 4,000/16,000

Memory Expansion Board - CODEExpansion of 64,000 with BufferOption

Memory Expansion Board - CODEExpansion of 128,000 with BufferOption

DIGI*TRAC 9600 BAUD MODEMASSEMBLY (Factory Set: Dial-UpLine)

Adds eight additional high security alarm inputs. SNAP, SAM andMOMENTUM support up to two boards in M2, M8, MSP or M64.Velocity supports up to four boards in M2, M8, MSP, M64 and up totwo boards in M16. Each input requires appropriate line module.Features removable connectors. UL Listed. CE.

Adds eight additional 2 Amp Form C relays to an M2, M8, M16 orMSP-8R. May not be installed in an M64. A total of �ve (four if networked) REB8 boards can be installed in all other DIGI*TRAC controllers. Removable connectors and status LEDs. UL Listed. CE.

Expands standard buffer from 1500 events and 1500 alarms to20,000 events and 2,000 alarms with CCM 7.X. Expands standardbuffer from 37 events and 37 alarms (700 events and 700 alarmswith CE boards) to 20,000 events and 2,000 alarms with CCM 6.6.Protected from data loss during power failures for up to 30 days bycontroller memory battery. UL Listed. CE.

Expands CODE Memory from 4,000 to 8,000 on Velocity andMOMENTUM with CCM 7.X. Not recognized by SNAP or SAMwith CCM 7.X. Expands CODE Memory from 1,000 to 16,000maximum with CCM6.X. Protected from data loss during power fail-ures for up to 30 days by controller memory battery. UL Listed. CE.

Expands CODE Memory by 64,000 (from 4,000 to 68,000) withCCM 7.X on Velocity and MOMENTUM. Not recognized byCCM 6.6 or earlier. A portion of the Code Memory may be allo-cated to alarm and event Buffers on Velocity only. Protected fromdata loss during power failures for up to 30 days by controllermemory battery. CE. UL Listed.

Expands CODE Memory by 128,000 (from 4000 to 132,000) withCCM 7.X on Velocity and MOMENTUM. Not recognized byCCM 6.6 or earlier. A portion of the Code Memory may be allo-cated to alarm and event Buffers on Velocity only. Protected fromdata loss during power failures for up to 30 days by controllermemory battery. CE. UL Listed.

A miniature 9600 Baud Modem Assembly that can be poweredfrom and installed internally in the M1, M2, M8, M16 or MSP for remotesite management via dial-up network. Includes cables, adaptor, andpower supply harness. Do not use at Host PC or NET*MUX4 out port.

Ordering Information –– Expansion Boards and Modem

Note: The DIGI*TRAC M2 controller can accommodate up to �ve expansion boards. Only one MEB/CE or MEB/CB is supported per controller.A maximum of four AEB8 expansion boards are supported per controller.

Note: Add “-230” to model number for 230 VAC.

identiv.comRevision/Date of Release: 2015-08

Identiv (NASDQ: INVE) is a global security technology company that establishes trust in the connected world, including premises, information, and everyday items. CIOs, CSOs and product departments rely upon Identiv’s trust solutions to reduce risk, achieve compliance, and protect brand identity. Identiv’s trust solutions are implemented using standards-drivenproducts and technology, such as digital certi�cates, strong authentication, mobility, and cloud services.

Technical data is subject to change without notice.

Copyright © 2015 Identiv, Inc. | All rights reserved. This document is Identiv public information.

Identiv has of�ces worldwide. Addresses and phone numbers are listed at identiv.com/contact. For more information, visit identiv.com or email sales@identiv.com.

DescriptionModel Comments

DescriptionModel Comments