Upload
dotuyen
View
214
Download
0
Embed Size (px)
Citation preview
Copper (Cu), Copper-Aluminium (CuAl) terminal lug installation 140G-I, 140G-JTerminali per cavi (Cu, CuAl)
(Cu, CuAl)Anschlüsse für KabelPrises pour câbles (Cu, CuAl)Terminales para cables (Cu, CuAl)
Bul. 140G/140MG
DIR 1000100R3810 Version 02
WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants. (Follow NFPA70E requirements).AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti. (Seguire i requisiti NFPA70E).WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen Sie die Anforderungen nach NFPA70E).AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée. Protéger le produit contre les environnements agressifs. (Vous devez respecter la norme NFPA70E).ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada. Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes. (Cumpra as exigências da norma NFPA70E).
Installation - Installazione - Instalación Instalação - -
DIR 1000100R3810 Version 02140G-I-TLA13, 140G-I-TLA14, 140G-I-TLA1A3, 140G-I-TLA1A4, 140G-J-TLA13, 140G-J-TLA14, 140G-J-TLC1B3, 140G-J-TLC1B4
140G-I 4p
x3 x4
140G-I 140G-J
警告:感電事故防止のため、取付けまたは修理の際は電源から取り外してください。適切なケース内に取付けてください。また、汚染物質がないことを確認してください。(NFPA70Eの要件に従ってください)
警告:为了防止触电,在安装或维修之前必须先切断电源。安装在合适的设备箱内。防止接触污染 。符合NFPA70E要求)物
Lug
Lug
Screw
CH 6
CH 5
LENGTH M1 0 mm (0.39") M 8
End cap kit
140G-J 3p 4p 3p
End cap kit
x3 x4
x3 x4 x3 x4
x3 x4 - -
- - x3 x4
x3 x4 x3* x4*
x3 x4 x3* x4*
Lug
CH 6
- - x3 x4
* = Not present on 140G-J-TLA1B3 and 140-J-TLA1B4
(Cu)
1
23,
3 m
m0,
13"
12
3
9 Nm80 lb-in
5,6 Nm
50 lb-in
140G-I-TLA133p example:
CH 5
LENGTH M1 0 mm (0.39") M 8
2,5…50 34140G-J-TLA14
140G-J-TLA13140G-I-TLA14
Stranded Flexible
Metric Wire Range (mm2)
34
Catalog No No of Poles Screw Head Type Wire Type AWG Wire Range
140G-I-TLA13
Slotted Cu/Al 14…1/0
Up to 100A
Up to 225A
140G-I-TLA1A3
22,6 Nm200 lb-in
9 Nm80 lb-in
12
3
3p example:
CH 6
CH 5
LENGTH M1 0 mm (0.39") M 8
(2)DIR 1000100R3810 Version 02
min
15.
5 m
mm
in 0
.61”
min
20
mm
min
0.7
9”
25…150 34140G-J-TLA1A4
140G-J-TLA1A3140G-I-TLA1A4
Stranded Flexible
Metric Wire Range (mm2)
34
Catalog No No of Poles Screw Head Type Wire Type AWG Wire Range
140G-I-TLA1A3
Hex Cu/Al 4 AWG…300 kcmil
3
DIR 1000100R3810 Version 02 (L8721) - B0736 Copyright © 2016 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 140G-IN122C-MU-P - March 2016
Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page
Up to 250A
42
1
25 Nm221 lb-in
CH 6
min
24
mm
min
0.9
4”
Stranded Flexible
Metric Wire Range (mm2)
3
Catalog No No of Poles Screw Head Type Wire Type kcmil Wire Range
140G-I-TLC1B3Hex Cu 250…350 120…185
4140G-J-TLC1B4
CONFIDENTIAL AND PROPRIETARY INFORMATION. THIS DOCUMENT CONTAINS CONFIDENTIAL AND PROPRIETARY INFORMATION OF
ROCKWELL AUTOMATION, INC. AND MAY NOT BE USED, COPIED OR DISCLOSED TO OTHERS, EXCEPT WITH THE AUTHORIZED WRITTEN
PERMISSION OF ROCKWELL AUTOMATION, INC.
Sheet
Size Ver
Of 11
A 0110000028320Dr. DateG. USHAKOW 8-23-13
MATERIALSIZE
FOLD
TO BE DETERMINEDBY STRATEGIC PARTNER
TO BE DETERMINEDBY STRATEGIC PARTNER
TO BE DETERMINEDBY STRATEGIC PARTNER
FLAT
SPECIFICATIONS FORINSTRUCTION SHEET CREATED BY STRATEGIC PARTNER
This Instruction Sheet is Being Printed by Strategic Partner
Note: After folding---Printed in (Country where printed*), part number(s) and barcode (when used) should be visible.
* The printing vendor may change the instruction sheet files to show the correct country.