Upload
buidien
View
243
Download
0
Embed Size (px)
Citation preview
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data
Technical Information:Prime Paint Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-002Colorstyle Paint Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-003
Frame, Door Opening Sizes and Hardware Provisions:1-3/8” Door - Single and Double . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-101Hardware Locations - Standard 1-3/8” Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-1021-3/4” Door - Single and Double . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-103Hardware Locations - Standard 1-3/4” Door 6-8, 7-0, 7-2 High, 4-1/2” or 5” High Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-104 7-10, 8-0, 9-0, 10-0 High, 4-1/2” or 5” High Hinge . . . . . . . . . . . . . . . . . . . . . . . .11-104A 5-0 Thru 10-0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-104B, 11-104C 6-8, 7-0, 7-2, 8-0 High, Dutch, 4-1/2” or 5” High Hinge . . . . . . . . . . . . . . . . . . . .11-104DHardware Locations - Optional (NAAMM), 1-3/4“ Door 6-8, 7-0, 7-2 High, 4-1/2” High Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-105 7-10, 8-0, 9-0 High, 4-1/2” High Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-105A 6-8, 7-0, 7-2 High, 5” High Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-106 7-10, 8-0, 9-0 High, 5” High Hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-106A1-3/8” Door Frames, Hinge and Strike Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-2011-3/4” Door Frames, 4-1/2” and 5” Hinge Preparations . . . . . . . . . . . . . . . . . . . . . . . . . .11-2021-3/4” Door Frames, ANSI (4-7/8”) Strike Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2031-3/4” Cylindrical Strike Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-204Series SQW Weatherstrip Kerf Frame Hinge Preparation. . . . . . . . . . . . . . . . . . . . . . . . . 11-205Series SQW Weatherstrip Kerf Frame Strike Preparation. . . . . . . . . . . . . . . . . . . . . . . . . 11-206Full Depth Hinge Reinforcement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-207High Frequency Hinge Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-2081-3/8” and 1-3/4” Door Frame Mute Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-209Reversible Flush Bolt Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-210
Frame Construction:Double Rabbet Frames, Die-cut, Welded Corner Assembly T-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-301Double Rabbet Frames, Die-cut, Welded Corner Assembly T-2, T-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-302Double Rabbet Frames, Die-cut, Welded Corner Assembly V-1, V-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-303Double Rabbet Frames, Die-cut, Welded Corner Assembly V-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-304Double Rabbet Frames, Miter-sawed, Welded Corner Assembly V-4, V-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-305Double Rabbet Frames, Coped, Butted, Welded Corner Assembly V-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-306Double Rabbet Frames, Welded Junctions Assembly V-8, V-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-307
SECTION 11 - FRAMES, GENERAL
INDEX
11-001
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data
Hardware Reinforcements:Closer Reinforcements, Plate Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-401, 11-402Miscellaneous Hardware Reinforcements, Plate Type . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-403
Frame Anchors:Anchor Quantity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-500Floor Anchors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-501 thru 11-503Masonry Anchors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-504, 11-505Existing Opening Anchors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-505 thru 11-507Wood Stud Anchors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-508, 11-509Metal Stud Anchors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-510, 11-511Before Drywall Stud Anchor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-512Closure Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-512Frame Splines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-513
Special Information:Standard Frame Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-901, 11-902Frame Spreader Bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-903
SECTION 11 - FRAMES, GENERAL
INDEX
11-001A
COLORSTYLE PAINT DATA DOOR FRAMES
Process Data
Factory-applied Colorstyle finish is a two-part, urethane top-coat that is electrostatically applied over the standard primer. The paint is then oven cured.
The chemically reactive cure provides a top quality, abrasion resistant finish with excellent weathering characteristics. This finish is environmentally friendly in that it does not contain heavy metal pigments.
60˚ Gardner Gloss: 15 to 20.Colors: Standard color selectors available upon request.
Performance Data
Colorstyle, factory applied finish paint process has been subjected to the following tests: Salt Spray Humidity Accelerated Weathering Impact Film Adhesion Abrasion
Factory applied Colorstyle finish paint meets the performance requirements and acceptance criteria as stated in ANSI Standard A250.3, “Test Procedure and Acceptance Criteria for Factory Applied Finish Painted Steel Surfaces...”.
11-003
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data
NOMINAL SIZES
NOMINAL DOOROPENING WIDTH
NO
MIN
AL
DO
OR
OPE
NIN
G H
EIG
HT
NOMINAL DOOR OPENING WIDTH
NO
MIN
AL
DO
OR
OPE
NIN
G H
EIG
HT
SINGLE FRAME
FLOORFINISH
DOUBLE FRAME
WIDTH WIDTH
2-8
2-10
3-0
2-4
2-6
2-0
5-4
6-0
5-8
4-8
5-0
4-0
OPENING HEIGHT
SINGLE PAIR
6-8 7-0 7-2
STANDARD DOOR OPENING SIZES
FRAMES ON THIS PAGE ARE FOR USE WITH 1-3/8" THICK DOORS.
1-3/8” DOOR FRAME
11-101
7-2 7-0 6-8 6-8
7-2 7-0 6-8
10.37"
9.75"
10.37"
9.75"
LC
STRIKEHEIGHT
STRIKEHEIGHT
*
LC
LC
LC
LC
LC
LC
LC
LC
32.9
3"32
.93"
31.9
3"
29.9
3"
31.9
3"
29.9
3"
59.8
7"
26.1
8"
24.1
8"
20.1
8"
19.5
"20
.18" 33.62"
40.31"
HIN
GE
SPA
CIN
G
HIN
GE
SPA
CIN
G
1640( )5"
810( )3"
9( )3"4
32 ()
1615"
15"
16(31
)
15"
16(29
)
15"
16(32
)
15"
16(31
)
15"
16(29
)
59 (7")
8
( 4 )3"9
26 (3" 16)
24 (16
)3"
20 (16
)3"
19 (1")
2(20
163")
10( )83"
( )833 5"
DUTCH DOOR FRAME
STANDARD FRAME
FRAME HEIGHTS
FRAME HEIGHTS
Labeled 6-8 frames require3 hinges.
2 hinges standard for non-labeled6-8 frames
3 hinges optional for non-labeled 6-8 frames
*
11-102
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data1-3/8” DOOR FRAMES HINGE AND STRIKE LOCATIONS
NOMINAL SIZES
1-3/4” DOOR FRAME SIZES
11-103
FLOORFINISH
NOMINAL DOOROPENING WIDTH
NO
MIN
AL
DO
OR
OPE
NIN
G H
EIG
HT
NOMINAL DOOR OPENING WIDTH
NO
MIN
AL
DO
OR
OPE
NIN
G H
EIG
HT
SINGLE FRAME DOUBLE FRAME
8-0
3-10
4-0
3-8
8-0
7-8
7-4
WIDTH WIDTH
2-8
2-10
3-6
3-4
3-0
2-4
2-6
2-0
5-4
7-0
6-8
6-0
5-8
4-8
5-0
4-0
OPENING HEIGHT
SINGLE PAIR
6-8 7-0 7-107-2 10-09-0
5-0 10-0
STANDARD DOOR OPENING SIZES
These hardware locations are Ceco Door Productsstandard and will be furnished unless
otherwise agreed to.
STANDARD HARDWARE LOCATIONS 1-3/4"DOOR FRAMES: 6-8, 7-0 & 7-2 HEIGHTS
4-1/2" OR 5" HIGH HINGES
11-104 12/1/04
9"
9"
DOOR OPENING HEIGHTS
6-87-07-2
34"
34"
33"
33"
31"
31"
STRIKEHEIGHT
CL
CL
CL
CL
41.81"
HIN
GE
SPA
CIN
G
13"1641( )
11-104
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataSTANDARD HARDWARE LOCATIONS 1-3/4”DOOR FRAMES: 6-8, 7-0 & 7-2 HEIGHTS4-1/2” OR 5” HIGH HINGES
These hardware locations are Ceco Door Productsstandard and will be furnished unless
otherwise agreed to.
approximation to .33".21/64" represents a measurable*
NOMINAL SIZES
STANDARD HARDWARE LOCATIONS FOR1-3/4” DOOR FRAMES:7-10, 8-0, 9-0, AND 10-0 HEIGHTS
11-104A
26"
34"
34"
26"
25.3
3"
26"
34"
41.81"
STRIKEHEIGHT
9"
9"
7-108-010-0
DOOR OPENING HEIGHTS
9-0
30"
30"
30"
CL
CL
CL
CL
CL
HIN
GE
SPA
CIN
G
13"1641( )
21"
64(25
)*
64(
)25
.33"
2521
"*
64(
)25
.33"
2521
"*
NOMINAL SIZES
FACTORY STANDARD HARDWARELOCATIONS: HEIGHTS 5’-0” THRU 10’-0”
11-104C
5'-1" 3 2 @ 21.5"
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
5'-2" 2 @ 22"
5'-3" 2 @ 22.5"
5'-4" 2 @ 23"
5'-5" 2 @ 23.5"
5'-6" 2 @ 24"
5'-7" 2 @ 24.5"
5'-8" 2 @ 25"
5'-9" 2 @ 25.5"
5'-10" 2 @ 26"
5'-11" 2 @ 26.5"
6'-0" 2 @ 27"
6'-1" 2 @ 27.5"
6'-2" 2 @ 28"
6'-3" 2 @ 28.5"
6'-4" 2 @ 29"
6'-5" 2 @ 29.5"
6'-6" 2 @ 30"
6'-7" 2 @ 30.5"
6'-8" 2 @ 31"
6'-9" 2 @ 31.5"
6'-10" 2 @ 32"
6'-11" 2 @ 32.5"
7'-0" 2 @ 33"
7'-1" 2 @ 33.5"
7'-2" 2 @ 34"
7'-3" 2 @ 34.5"
7'-4" 2 @ 35"
7'-5" 2 @ 35.5"
7'-6" 2 @ 36"
9'-9"
10'-0"
9'-11"
9'-10"
9'-2"
9'-8"
9'-7"
9'-6"
9'-5"
9'-4"
9'-3"
9'-1"
9'-0"
8'-11"
8'-10"
8'-9"
8'-8"
8'-1"
8'-7"
8'-6"
8'-5"
8'-4"
8'-3"
8'-2"
8'-0"
7'-11"
7'-10"
7'-9"
7'-8"
7'-7" 4 3 @ 24.33"4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
3 @ 24.66"
3 @ 25"
3 @ 25.33"
3 @ 25.66"
3 @ 26"
3 @ 26.33"
3 @ 26.66"
3 @ 27"
3 @ 27.33"
3 @ 27.66"
3 @ 28"
3 @ 28.33"
3 @ 28.66"
3 @ 29"
3 @ 29.33"
3 @ 29.66"
3 @ 30"
3 @ 30.33"
3 @ 30.66"
3 @ 31"
3 @ 31.33"
3 @ 31.66"
3 @ 32"
3 @ 32.33"
3 @ 32.66"
3 @ 33"
3 @ 33.33"
3 @ 33.66"
3 @ 34"
5'-0" 2 42"
OPENING HEIGHT NUMBER OF HINGES DIM "A"
OPENING HEIGHT NUMBER OF HINGES DIM "A"
OPENING HEIGHT NUMBER OF HINGES DIM "A"
LC
9"
DOOR OPENING HEIGHTS
7-2 7-0 6-8
HEIGHTSTRIKE
8-0
33.62"
9"
CL
LC
LC
LC
38.3
1"
28.3
1"
26.3
1"
22.3
1"
17.3
7"H
ING
E SP
AC
ING
16(
5"38
)
5"(
)16
28
5"(
)16
26
5"(
)16
22
22.3
1"(
16)
225"
17 (3")
8
33( 5")8
otherwise agreed to.standard and will be furnished unless
These hardware locations are Ceco Door Products
11-104D
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataSTANDARD HARDWARE LOCATIONS, 1-3/4”DUTCH FRAMES: 6-8, 7-0, 7-2 & 8-0HEIGHTS - 4-1/2” OR 5” HIGH HINGES
HARDWARE LOCATIONS SHOWN BELOW ARE BASEDON THE FOLLOWING:
5" from head to top of upper hinge.10" from bottom of jamb to bottom of lower
Equal spacing between intermediate hinges.
The above hardware locations will befurnished only when agreed to.
Strike Height On Frame IsDependent On Knob OrCrossbar Height. Refer ToDoor Hardware Locations(p. 01-403) And Manufacturer'sLock Template To DetermineRelationship Between Lock And Strike.
hinge.
NOMINAL SIZES
NAAMM ALTERNATE HDWE LOCATIONS, 1-3/4”DOOR FRAMES: 6-8, 7-0 & 7-2 HEIGHTS4-1/2” HIGH HINGES
11-105
LC
LC
12.25"
7-2
DOOR OPENING HEIGHTS
LC7.25"
6-87-0
33.2
5"
32.2
5"
30.2
5"H
ING
E SP
ACI
NG
33.2
5"
32.2
5"
30.2
5"
7( 1" )4
33 (1"
)4
)4
(321"
)4
(301"
)4
(331"
(4
)32
1"
30 (4
)1"
( 4 )12 1"
The above hardware locations will befurnished only when agreed to.
hinge.10" from bottom of jamb to bottom of lower5" from head to top of upper hinge.
ON THE FOLLOWING:HARDWARE LOCATIONS SHOWN BELOW ARE BASED
Equal spacing between intermediate hinges.
approximation to .83".53/64" represents a measurable*
(p. 01-403a) And Manufacturer'sLock Template To DetermineRelationship Between Lock
Strike Height On Frame Is
Crossbar Height. Refer ToDoor Hardware Locations
Dependent On Knob Or
And Strike.
NOMINAL SIZES
NAAMM HDWE LOCATIONS, 1-3/4” DOORFRAMES: 7-10, 8-0, 9-0, AND 10-0HEIGHTS - 4-1/2” HIGH HINGES
11-105A
L
12.25"LC
CL
DOOR OPENING HEIGHTS
10-0 9-0
7.25"
7-108-0
C
CL
HIN
GE
SPA
CIN
G24
.83"
7( )1"4
( )412 1"
33.5
"2
()
1"33
29.5
"2
()
1"29
25.5
"2
()
1"25
53"
64(24
)*
24.8
3"24 (
* )53
"64
24.8
3"24 (
* )53
"64
)(
233
.5"
331"
29.5
"29
)(
1" 2 1")
(25
.5"
252
)(
233
.5"
331"
29.5
"29
)(
1" 2 1")
(25
.5"
252
The above hardware locations will befurnished only when agreed to.
HARDWARE LOCATIONS SHOWN BELOW ARE BASED ON THE FOLLOWING:
5" from head to top of upper hinge.10" from bottom of jamb to bottomof lower hinge.Equal spacing between intermediatehinges.
(p. 01-404) And Manufacturer'sLock Template To DetermineRelationship Between Lock
Strike Height On Frame Is
Crossbar Height. Refer ToDoor Hardware Locations
Dependent On Knob Or
And Strike.
33"
LC
LC
12.5"
32"
30"
7-2
DOOR OPENING HEIGHTS
33"
LC
32"
30"
7.5"
6-87-0
HIN
GE
SPA
CIN
G
7( 1" )2
12( 1" )2
11-106
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataNAAMM ALTERNATE HDWE LOCATIONS, 1-3/4”DOOR FRAMES: 6-8, 7-0 & 7-2 HEIGHTS5” HIGH HINGES
The above hardware locations will befurnished only when agreed to.
hinge.10" from bottom of jamb to bottom of lower5" from head to top of upper hinge.
ON THE FOLLOWING:HARDWARE LOCATIONS SHOWN BELOW ARE BASED
Equal spacing between intermediate hinges.
approximation to .33".21/64" represents a measurable*
21/32" represents a measurableapproximation to .66".
*
(p. 01-404a) And Manufacturer'sLock Template To DetermineRelationship Between Lock
Strike Height On Frame Is
Crossbar Height. Refer ToDoor Hardware Locations
Dependent On Knob Or
And Strike.
L
LC
CL
DOOR OPENING HEIGHTS
10-0 9-0
7.5"
7-108-0
C
CL
12.5"
33.3
3"
29.3
3"
25.3
3"
24.6
6"H
ING
E SP
ACI
NG
7( 1" )2
33.3
3"
29.3
3"
25.3
3"
24.6
6"
33.3
3"
29.3
3"
25.3
3"
24.6
6"
12( 1" )2
21"
32(24
)
21"
64(25
)
21"
64(29
)
21"
64(33
))
(6421
"33 29
)(
21"
64
)(
21"
6425
3221"
24 ()
)(
6421"
33 29)
(21
"64
)(
21"
6425
3221"
24 ()
* * * *
****
* * * *
11-106A
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataNAAMM ALTERNATE HDWE LOCATIONS1-3/4” DOOR FRAMES: 7-10, 8-0, 9-0AND 10-0 HEIGHTS - 5” HIGH HINGES
IS WELDED TO JAMBAFTER HINGE REINF.SNAPPED-IN PLACEPLASTER GUARD IS26 GAGE STEEL
GUARDPLASTER
PER FRAME GAGEFACE NOTCH VARIES
HINGE PREPARATION
TAPPED HOLES FOR #10-24 MS(3) PLACES
FOR USE WITH 3-1/2" HIGHTEMPLATE HINGES (ANSI A156.7)
STEEL STRIKE REINF.PROJECTION WELDED(2) PLACES EACH END
16 GAGE FORMED
16 GAGE STRIKEREINFORCEMENT
PLASTER GUARDFORMED AS PARTOF STRIKE REINF.
STRIKE REINFORCEMENTUSE WITH CYLINDRICAL LOCKS ONLY
(1-1/8" x 2-3/4" "T" STRIKE)
PIERCE, DRAW ANDTAP FOR #8-32 MSTO PROVIDE A MIN.1/8" THREAD DEPTH
12 GA. HINGE REINF.PROJECTION WELDEDTO FRAME (3) PLACESEACH END
5/16"(NOM.)BACKSET
1-1/4"
8"
1-9/16"
3-1/2"
1-25/64"
1-25/64"
23/64"
23/64"
3/8"
21/64"
BACKSET
1-9/16"
1-5/32"
FACE NOTCH VARIESPER FRAME GAGE
3/16"(NOM.)
7/32"
2-25/32"
2-1/8"
1-17/32"
21/64"
21/64"
(NOM.)1-1/4"
NOMINAL SIZES
1-3/8” DOOR FRAMESTRIKE AND HINGE PREPS
11-201
11-202
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data1-3/4” DOOR FRAME4-1/2” & 5” HINGE PREPS
16 GAGE FORMED STEEL STRIKEREINFORCEMENT PROJECTIONWELDED (2) PLACES EACH END
PIERCE, DRAW AND TAP FOR#8-32 MS TO PROVIDE AMINIMUM 1/8" THREAD DEPTH
PLASTER GUARD FORMEDAS PART OF STRIKEREINFORCEMENT
2 1"8
1 17"32
2 25"32
13"32
1 5"32
21"64
21"64
1 15"16
CUTOUT
(NOM.)BACKSET
3"8
11-204
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data1-3/4” DOOR FRAME CYLINDRICAL STRIKE PREPARATION
2
NOMINAL SIZES
SERIES SQW WEATHERSTRIPKERF FRAME HINGE PREPARATION
11-205
FACE NOTCH VARIES
5/16"
5/8"
1/2"
1-1/4"
9"
PER FRAME GAGE
2-1/8"
AND HINGE WEIGHT
4-1/2"
1/2"(NOM.)
1-1/8"
1-1/8"
1-1/4"
1/2"
(N0M.)1-5/8"
BACKSET
2-1/8"
BACKSET1/2"(NOM.)
1-1/2"
1-1/4"
FACE NOTCH VARIESPER FRAME GAGEAND HINGE WEIGHT
1/2"
5"
1-1/4"
1/2"
(N0M.)1-5/8"
5/16"
5/8"
9"
1-1/4"
FIT FOAM FILLEDWEATHERSTRIP
TO FRAMEAFTER FINISH
PAINTING
PLASTERGUARD
2
PLASTER GUARD ISSNAPPED-IN PLACE.HINGE REINFORCEMENT
26 GAGE STEEL
IS WELDED TO JAMB.
4-1/2" HINGE PREP
(ANSI A156.7)TEMPLATE HINGESFOR USE WITH 5" HIGH
5" HINGE PREP
FOR USE WITH 4-1/2" HIGH
PLASTER GUARD ISSNAPPED-IN PLACE.HINGE REINFORCEMENTIS WELDED TO JAMB.
TEMPLATE HINGES(ANSI A156.7)
26 GAGE STEEL
PLACES EACH END
(4) PLACESFOR #12-24 MS
TAPPED HOLE
7 GAGE HINGEREINFORCEMENTPROJECTION WELDED (4)
(4) PLACES.180 HINGESREMOVED FORBUT MUST BEFOR .134 HINGESREMAIN INTACT ELEVATED PIPS
TAPPED HOLE FOR
PLASTER
7 GAGE HINGE REINFORCEMENTPROJECTION WELDED TO FRAME(4) PLACES EACH END
#12-24 M.S.(4) PLACES
GUARD
11-206 12/1/04
4 1"8
2 1"8
BACKSET (NOM.)
CUTOUT
1"2
11"32
1 9"32
3 13"32
4 29"32
1"2 8
1 17"32
2 1"8
2 25"32
9"16
1 5"32
13"32
BACKSET (NOM.)
CUTOUT
FACE NOTCH VARIESPER FRAME GAGE
25"64
25"64
6421"
21"64
16 GAGE FORMEDSTEEL STRIKE REINF.PROJECTION WELDED(2) PLACES EACH END
PIERCE, DRAW AND TAP FOR #8-32 MSTO PROVIDE A MIN.1/8" THREAD DEPTH
12 GAGE STEEL STRIKE REINF.PLATE - PROJECTIONWELDED TO FRAME (6) PLACES
PUNCH AND TAPFOR 12-24 MS(2) PLACES
16 GAGE STRIKE REINFORCEMENT
PLASTER GUARDFORMED AS PARTOF STRIKE REINF.
FIT FOAM FILLEDWEATHERSTRIP TOFRAME AFTER FINISHPAINTING
26 GAGE STEELSNAP-IN PLASTERGUARD
11-206
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataSERIES CF PROFILE WKWEATHERSTRIP - KERF FRAME STRIKE PREPARATION
NOMINAL SIZES
1-3/4” DOOR FRAME, FULL DEPTHHINGE REINFORCEMENT
11-207
TAPPED HOLEFOR #12-24 MS(4) PLACES
1 1"4
4 1"2
1"2
1"2
81"1
1"1 8
1 15"16
1 5"8
5" (NOM)16
(NOM.)
BACKSET
12"
5"16
5"8
7 GAGE HINGE REINFORCEMENT WELDED TO FRAME
AVAILABLE FOR FRAME DEPTHS5-1/2" THRU 10-5/8"
4-1/2" HIGH HINGEAPPLICATION SHOWN
FRAME WIDTHLESS 1/2"
XXX
X
XXX
X
XXX
X
XXXX
"
"18
34
5/8" STOP
1"
2"
1/4" LONG ARC WELDS(3) PLACES PER STRAP
HINGE REINFORCEMENT ANDPLASTER GUARD APPLIEDPER PAGE #11-202
STEEL STRAP
11-208
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataDOOR FRAME HIGH FREQUENCYHINGE REINFORCEMENT STRAP
NOMINAL SIZES
DOOR FRAME MUTES
11-209
9 3/4" MAX.
C OF
STRIKEL
M M
6" ON CENTERM
12" MAX.
12" MAX.
M
M
INSERT BLUNT END OF 3/32" DIAMETER WIREOR TOOL IN HOLE IN CENTER OF MUTE.
MOISTEN CONE PORTION AND INSERT IN HOLE INSTOP OF FRAME, PUSHING SLOWLY WITH CIRCULARMOTION TO ELONGATE MUTE SUFFICIENTLY TOSET IN PLACE.
REMOVE WIRE
1.
2.
3.
DOOR MUTES (SILENCERS) MAINTAIN PROPERSPACE (1/16") BETWEEN DOOR AND FRAMESTOP AND CUSHION DOOR CLOSING. INSERTMUTES INTO FRAME BEFORE FRAME IS INSTALLED INTO WALL TO PREVENT GROUT,PLASTER, ETC. FROM FILLING HOLES.
SINGLE SWING DOUBLE SWING
STANDARD LOCATION OF DOOR MUTES
SINGLE SWING DOOR FRAMES - 3 MUTES DOUBLE SWING DOOR FRAMES - 2 MUTES DUTCH DOOR FRAMES - 4 MUTES
M = MUTE
Fed. Spec. Type 1337A
Note 1Pips are provided forprojection welding. Ifother welding is used,flip Part A over.
A. (12 ga. galv. steel)
B. (16 ga. galv. steel, prime paint)
D. #8-32 x 1/2" UCFHMS (2)
STRIKE FILLER
STRIKE
REINFORCEMENT
PLASTER GUARD
Part B
Tackweld Part E on back ofreinforcement as necessary.
Note 1
RRA/LA shownFlip flop Part Bfor LRA/RA
Center of cutoutand door
Center line of Door Opening Widthand Cutout
HEAD
Part C
Part B
Part A
Tapped for#8-32 MS
Weld Part Ato Head at each side
Part A
Part D
E. Plaster guard (Included on SU and SQ frames only)
RFB AssemblyParts A,B, and D as listedbelow:
C. (16 ga. galv. steel, prime paint)
15/16"
11-210
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataREVERSIBLE FLUSH BOLT PREPARATION
WELDING TYPE T-1 "STITCH WELD at SOFFIT ONLY"Standard KD frame components from stock with corner reinforcements.NO SAWING REQUIRED.
WELDING TYPET-1
(1-1/2" wide and up)
jamb soffit seam.end of the head andwelds located at eachTwo 1/2" long stitch
located in the centerlength stitch weld,One 1/2" (minimum)
WIDE STOP
Wide Stop:
(up to 1-1/2" wide)NARROW STOP
of the soffit.
Narrow Stop
Reference: This corner has a full and continuousbackbend at the head and jambs. It can be usedon frames that cap the wall.
FACE-MITER SEAMIS VISIBLE
STANDARD KD JAMB
STANDARD KD HEAD
1. Assemble frame: Bend tabs after assuring that face-miter seam is "closed" and "tight". Bend corner reinforcement tabs toward inside (toward throat) of frame. Bend rabbet tabs towards outside (toward jamb backbends).
2. Place weld bead as required at the joint of the head and jamb soffits from the backside.
2a. If weld penetration occurs, file smooth.
2b. Spot paint
NOMINAL SIZES
DIE-CUT, DOUBLE-RABBET FRAMEWELDED CORNER ASSEMBLY
11-301
Reference: This corner has a fulland continuous backbend at the headand jambs. It can be used on framesthat cap the wall.WELDING TYPE T-2 "OUTSIDE FACE WELD ONLY"
Standard KD frame components from stock with corner reinforcements.NO SAW CUTTING REQUIRED.
Reference: This corner has a fulland continuous backbend at the headand jambs. It can be used on framesthat cap the wall.
3. Grind an dress smooth bothface-miter seams after welding.
head and jamb, from the outside (Both faces).
11-302
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataDIE-CUT, DOUBLE-RABBET FRAMEWELDED CORNER ASSEMBLY
2. Weld the entire face-miter seam, between
COMPLETELY INVISIBLEFACE-MITER SEAM IS
STANDARD KD HEAD
STANDARD KD JAMB
Standard KD frame components from stock with corner reinforcements.NO SAW CUTTING REQUIRED.
WELDING TYPE T-2 "OUTSIDE FACE WELD and FULL WEB WELD"
4. Weld the entire web seam(including the seams betweenhead and jamb rabbets, stopsand soffits) from the backside,
4a. If weld penetration occurs, file smooth.
5. Spot paint
1. Assemble frame: Bend tabs after assuring that face-miter seam is "closed" and "tight" Bend corner reinforcement tabs toward inside (toward throat) of frame. Bend rabbet tabs toward outside(toward jamb backbends) of
2. Weld the entire face-miter seam, between head and jamb, from the outside (both faces).
3. Grind and dress smooth both face-miter seams after welding.
3a. Spot paint
frame.
2
STANDARD KDHEAD
STANDARD KDJAMB
FACE-MITER SEAMIS COMPLETELYINVISBLE
T-3
toward outside(toward jamb backbends) of (toward throat) of frame. Bend rabbet tabs Bend corner reinforcement tabs toward inside that face-miter seam is "closed" and "tight"1. Assemble frame: Bend tabs after assuring
frame.
with a continuous weld bead.
T-2
NOMINAL SIZES
DIE-CUT, DOUBLE-RABBET FRAMEWELDED CORNER ASSEMBLY
11-303
Reference: This corner has a fulland continuous backbend at the headand jambs. It can be used on framesthat cap the wall.
COMPLETELY INVISIBLEFACE-MITER SEAM IS
DIE-CUT HEAD
DIE-CUT JAMB
V-2
Die-cut frame components - VOID OF CORNER REINFORCEMENTSNO SAW CUTTING REQUIRED
WELDING TYPE V-2 " INSIDE FACE WELD ONLY"
2. Weld the entire face-miter seam from the inside.Weld is to penetrate to exterior.
2a. Grind the exterior face and fill as necessary.
rabbet tabs toward outside (toward jamb backbends) face-miter seam is "closed" and "tight". Bend
1. Assemble frame: Bend tabs after assuring that
of frame.
11-304
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataDIE-CUT, DOUBLE RABBET FRAMEWELDED CORNER ASSEMBLY
Reference: This corner has a fulland continuous backbend at the headand jambs. It can be used on framesthat cap the wall.
FACE-MITER SEAM ISCOMPLETELY INVISIBLE
DIE-CUT HEAD
DIE-CUT JAMB
Die-cut frame components - VOID OF CORNER REINFORCEMENTSNO SAW CUTTING REQUIRED.
WELDING TYPE V-3 "INSIDE FACE WELD and FULL WEB WELD"
1. Assemble frame: Bend tabs after assuring that face-miter seam is "closed" and tight. Bend rabbet tabs toward outside (toward jamb backbends) of frame.
2. Weld the entire face-miter seam from the inside. Weld is to penetrate to exterior.
2a. Grind the exterior face and fill as necessary.
3. Dress reworked areas.
4. Weld the entire web seam (including the seams between head and jamb rabbets, stops, and soffits) from the backside with a continuous weld bead.
4a. If weld penetration occurs, file smooth.
5. Spot weld.
V-3
42
1a. Clamp the head and jamb at 90˚.
2. Clamp head and jamb at 90˚.
frame sections is 90˚.
11-308
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech Data4” & 6” HOSTPITAL STOPS
CLOSER MOUNTINGREGULAR ARM
JAMBHINGE
RABBETDOOR(1) 1" LONG (APPROX)
STITCH WELD AT EACHEND OF PLATE END OF PLATE
STITCH WELD AT EACH(1) 1" LONG (APPROX)
HINGEJAMB
HEAD
PARALLEL ARMCLOSER MOUNTING
REINFORCEMENT PLATE:14 GAGE MIN. STEEL x 1/3/4" x 14" (1)REINFORCEMENT PLATE: REINFORCEMENT PLATE:
14 GAGE MIN. STEEL x 1/3/4" x 14" (1)Note: If 1-3/4" dimension is too bigto fit stop ..decrease size to suit.
LOCATION OFOPTIONALPLATE, SEE11-402
REINFORCEMENT PLATE:14 GAGE MIN. STEEL x 1/3/4" x 14" (1)REINFORCEMENT PLATE:
END OF PLATESTITCH WELD AT EACH(1) 1" LONG (APPROX) DOOR
RABBET
HINGEJAMB
TOP JAMBCLOSER MOUNTING
to fit stop ...decrease size to suit.Note: If 1-3/4" dimension is too big
14 GAGE MIN. STEEL x 1/3/4" x 14" (2)REINFORCEMENT PLATE:
CLOSER MOUNTINGCORNER BRACKET
JAMBHINGE RABBET
DOOR
(1) 1" LONG (APPROX)STITCH WELD AT EACHEND OF EACH PLATE
14"
STOP
PLACE FLAT AGAINSTINSIDE OF FACE ANDBUTT AGAINST INSIDEOF DOOR RABBET.
AND BUTT AGAINST INSIDEINSIDE OF DOOR SOFFITPLACE FLAT AGAINST
DOORRABBET
OF DOOR STOP
OF DOOR STOP
PLACE FLAT AGAINSTINSIDE OF DOOR SOFFITAND BUTT AGAINST INSIDE
OF HEAD BACKBEND.BUTT AGAINST INSIDEINSIDE OF FACE ANDPLACE FLAT AGAINST
Note: Verify against manufacturer's templatethat size and position of plate satisfyhardware needs.
Note: Do not use withstandard DW plumbanchor . Not recom-mended when dooropening height isless than 7'-'0".
Note: If 1-3/4" dimension is too bigto fit face ...decrease size to suit.
Note: If 1-3/4" dimension is too bigto fit face ...decrease size to suit.
NOMINAL SIZES
CLOSER REINFORCEMENTPLATE TYPE
11-401
14"4" 2" 14"
2" 14"14"
HEAD
HEADHEAD
END OF PLATESTITCH WELD AT EACH(1) 1" LONG (APPROX)
OUTSWING DOOR: SURFACE BOLTSAND REMOVABLE MULLIONS
REINFORCEMENT PLATE:14 GAGE MIN. STEEL x 1/3/4" x 14" (1)
Note: If 1-3/4" dimension is too bigto fit stop ..decrease size to suit.
AND BUTT AGAINST INSIDEINSIDE OF DOOR SOFFITPLACE FLAT AGAINST
DOORRABBET
OF DOOR STOP
Note: Verify against manufacturer's templatethat size and position of plate satisfyhardware needs.hardware needs.
that size and position of plate satisfyNote: Verify against manufacturer's template
INSIDE OF DOOR FACE
RABBETDOOR
PLACE FLAT AGAINST IN-SIDE OF RABBET OPPOSITEDOOR AND BUTT AGAINST
11-401PLATE, SEEOPTIONALLOCATION OF
to fit face ..decrease size to suit.Note: If 1-3/4" dimension is too big
14 GAGE MIN. STEEL x 1/3/4" x 14" (1)REINFORCEMENT PLATE:
CLOSER MOUNTINGPARALLEL ARM
JAMBHINGE
(1) 1" LONG (APPROX)STITCH WELD AT EACHEND OF PLATE
hardware needs.that size and position of plate satisfyNote: Verify against manufacturer's template
OF DOOR RABBET
RABBETDOOR
PLACE FLAT AGAINSTINSIDE OF FACE ANDBUTT AGAINST INSIDE
to fit face ..decrease size to suit.Note: If 1-3/4" dimension is too big
14 GAGE MIN. STEEL x 1/3/4" x 14" (1)REINFORCEMENT PLATE:
INSWING DOOR: SURFACE BOLTS
(1) 1" LONG (APPROX)STITCH WELD AT EACHEND OF PLATE
JAMBBOTTOM OF STRIKE
RABBETDOOR
END OF PLATESTITCH WELD AT EACH(1) 1" LONG (APPROX)
REINFORCEMENT PLATE:14 GAGE MIN. STEEL x 1/3/4" x 14" (1)
Note: If 1-3/4" dimension is too bigto fit stop ..decrease size to suit.
PLACE FLAT AGAINSTINSIDE OF DOOR SOFFITAND BUTT AGAINST INSIDEOF DOOR STOP
RIM TYPE PANICDEVICE MOUNTING
14"
14"2" 7"
33-5/16"
40-5/16"
14"
7"
cL
HEADHEAD
CL of opening
L of openingC
HEAD
7"
14"
11-402
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataCLOSER REINFORCEMENTPLATE TYPE
SECTIONFRAME HEAD
1-15/16"RABBET
DOORSIDE
HEAD
CR/HALF
SPOT OR TACKWELDED IN PLACE.
(2) WELDS PER END
REGULAR & PARALLELARM CLOSER MOUNTING
14GA. GALV. STL.
NOMINAL SIZES
HALF-CLOSER REINFORCEMENT
11-403
1-5/8"
5/8"
1-1/2"
1-31/32"
13-7/8"
2" MIN.FACE
4" 13-7/8"
HINGEJAMB
NOMINAL SIZES
JAMB ANCHOR QUANTITIESFOR STANDARD HEIGHT FRAMES
11-500
* Floor anchors may be omitted and replaced with two additional jamb anchors.
Unless otherwise indicated, jamb anchors are normally located on the same center line as the hinge preparations except where interference would occur with hardware reinforcements. Where interference would occur, anchors should be positioned above or below hinge reinforcements and directly opposite on the strike jamb.
For sizes other than listed above, the following guidelines are followed (unless otherwise indicated)...For heights to 6-0: Two jamb anchors per jamb; For heights greater than 6-0 thru 7-6: Three jamb anchors per jamb; For heights greater than 7-6 thru 10-0: Four jamb anchors per jamb; and for each additional 2 feet of height or fraction thereof: One additional jamb anchor per jamb.
ANCHOR TYPE
NEW MASONRY 6 8
8 10 OMIT
2
2 *
6 8 2WOOD STUD
METAL STUD
SOLID PLASTER
LAMINATEDDRYWALL
EXISTING OPENING
QUANTITY
6-8 THRU 7-2 7-10 THRU 10-0
FLOOR ANCHORSPER FRAME
JAMB ANCHORS PER FRAME
*
6 8
2 *6 8
2 *6 8
NOMINAL SIZES
WELDED FLOOR ANCHOR
11-501
3-1/8
1-23/32
1-7/16
1/2
1/21/2
5/16 DIA.HOLES
1-1/2
1-1/2
1/2
DIM A
1" CTCSPACES
5/16 DIA.HOLES
11/16 11/16
DIM A FRAME DEPTH HOLES
3-1/25
6-1/28
4-1/2 to 5-1/45-3/8 to 6-3/46-7/8 to 8-1/48-3/4 to 9-3/4
3568
ONE PIECE ANCHOR SELECTION CHART
All dimensions are in inches. For SI conversion: 1" = 25.4 mm.Anchors for depths outside the above range are made to order.
TWO PIECE ANCHOR
(16 GA. GALV.)(16 GA. COLD ROLLED)
CENTER OF JAMBAND ANCHOR
16 GAGEGALV STEEL
WELDWELD
TWO PIECE APPLICATION ONE PIECE APPLICATION
11-502
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataADJUSTABLE FLOOR ANCHOR
4" TRAVEL
2-1/8"
5/16" DIA.2-1/8"
O.A.
HAT:4-1/4" WIDE x 3/4" LEGSx 5/8" OFFSET @ 3-1/4"LONG
ANGLE:1-1/2" x 6-3/4" @ 2-3/4"LONG
SCREW:#10 x 3/4" THSMS
FLUSH WITHJAMB BOTTOM
Dim A = Depth (-) 1-3/16"(assuming 1/2" backbends)
Dim A
Dim A
Dim A = Depth (-) 3/16"
FLOOR
FLOOR
IMPOST
IMPOST
Note: Anchor is attached to floor attwo places. Mullion or sill is slippedover anchor (fastening is optional).
12 GAGESTEEL
(2) 9/32"DIA. HOLES
Note: Position sill anchorto avoid possible interferencewith sill bracing strap ifpresent.
SILL BRACINGSTRAP
FOR VERTICAL MULLIONS
FOR BASE SILLS
NOMINAL SIZES
SIDELITE FLOOR ANCHOR
11-503
11-504
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataANCHORS FOR NEW MASONRY
1-13/16"
8-1/4"
2"
8"
R 1-1/4"
2-5/16"9-3/8"
2"
MASONRY "T" ANCHOR
WIRE MASONRY ANCHOR
SPOTWELDED
16 GAGEGALV STEEL
DEPTH
6-3/4
7-3/4
8-3/4
4-3/4
5-3/4
DEPTH
5-1/4
4-1/4
4-1/44-3/4 3-3/4
3-3/4
MFGFIELD MODIFIED DEPTH
THROAT RANGE
2 THRU 8-3/4
All dimensions are in inches; forSI conversion, 1" = 25.4 mm.
7 GAGE GALV.STEEL WIRE
- -
44
34
3
44
3
54
1
1
34
4
4 1
334
4
NOMINAL SIZES
MASONRY ANCHORS CONT.EXISTING OPENING ANCHOR
11-505
Available on specialorder only
order onlyAvailable on special
WELDED
YOKE AND STRAP MASONRY ANCHOR
EXISTING OPENING ANCHOR
FOR ALLFRAME DEPTHS
11-506
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataEXISTING OPENINGSTANDARD JAMB ANCHOR
NOMINAL SIZES
EXISTING OPENING ANCHORFOR SPECIAL FACES
11-507
All dimensions are in inches. For SI conversion: 1" = 25.4mm.Dimension A assumes a 5/8 frame stop height.Suggested Rough-opening clearance: 1/4" @ head and jambs.See page 11-506 for jamb punching, spacing, fastener, and floor anchor notes.
EXISTING OPENING/NARROW ANCHOR SIZE CHART
FACE 1 1-1/4 1-1/2 1-3/4 2 2-1/2
DIM A 1-9/16 1-13/16 2-1/16 2-5/16 2-9/16 3-1/16
EXISTING OPENING/NARROW
1
1-1/2
3-1/4
DIM A
1
1-1/4
1/8
11-508
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataWELDED WOOD STUD ANCHOR
5/8
JAMB DEPTHEQUALS WALL
THICKNESSPLUS 1-1/8
3/16
*DIM "X"
MSZ1 ANCHORSPOT WELDEDTO JAMB
SPOT WELDED TOMSZ1 ANCHOR
5/32 DIA. HOLES(2) PLACESEACH STRAP
JAMB
WALL SECTIONWood blocking bycontractor asnecessary.
to stud bycontractor
TOSUITWALL
The wood stud anchor depicted below is shop attached. Unless otherwise designated, a stud anchor willbe attached at each sill in lieu of a floor anchor.
18 GAGESTEEL
WOOD STUD ANCHOR SELECTION CHART
STUD SIZE
2 x 4
2 x 6
DIM "X"
3-1/2
5-1/2
INSTALLATION SEQUENCE1. WALL FRAMING2. DOOR FRAME3. WALL SURFACE MATERIAL
* Or to suit other stud sizes.For stud sizes other than shownbelow: actual stud dimension shouldbe noted. Also, wall board thicknessesshould be shown so that straps canbe properly positioned.
PORTION OF JAMBREMOVED FOR CLARITY
Straps are nailed
STRAP ANCHOR
All dimensions are in inches, forSI conversion, 1" = 25.4 mm.
NOMINAL SIZES
ADJUSTABLE JAMB ANCHORFOR STUD WALLS
11-509
ASSEMBLY DETAIL(END VIEW)
Anchors are adjustable in 1/8"increments within given ranges.
Metal stud similarWood stud shown
FRAMEHOLLOW METAL
FRAME ANCHOR
WALL BOARD
WALL STUD
NAILS OR SCREWS
TYPICAL APPLICATION
FRAME DEPTH: 3-3/4" thru 6-1/4" FRAME DEPTH: 6-1/4" thru 8-3/4"
87
4
5
6
6 14
8
11-510
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataWELDED METAL STUD ANCHOR RECESSED TYPE
5/8
DIM "A"
EQUAL
EQUAL
JAMB
WALL SECTION
The metal stud anchor depicted below is shop attached. Unless otherwise designated, a stud anchor willbe provided for each sill.
18 GAGESTEEL
Stud isscrewedto anchor
If second studis used, attachit after jambis fastened.
2. WALL FRAMING1. DOOR FRAMEINSTALLATION SEQUENCE
3. WALL SURFACE MATERIAL
3-1/2 4-1/2 THRU 5-1/4
8-3/8 THRU 9-3/4
5-3/8 THRU 6-3/4
6-7/8 THRU 8-1/46-1/2
8
5
DEPTH RANGEDIM"A"
FRAME
ZEE ANCHOR (1x1-1/4x1 @ Dim "A" long)SPOT WELDED TO JAMB
MSZ anchor andstop as necessary
clip is welded tox 1 long steel "zee"a 3/4 x 5/8 x 3/4depths over 4 inches,For single rabbet
All dimensions are in inches, forSI conversion, 1" = 25.4 mm.
NOMINAL SIZES
WELDED METAL STUD ANCHORFLUSH TYPE
11-511
DIM "C"DIM "A"
DIM "B"
DIM "B"
Allow 3/16" clearancebetween studand jamb
The metal stud anchor depicted below is shop attached. at sill.
For single rabbetdepths over 4 inches,a 3/4 x 5/8 x 3/4x 1 long steel "zee"clip is welded toMSZ anchor andstop as necessary
Stud isscrewed to anchor
Series BQ shouldbe considered
If second studis used, attachit after jambis fastened.
4-5/85-7/8
7-1/2 2-1/8
1-7/16
13/16
3-1/43
3 5-3/8 THRU 66-1/8 THRU 7-5/8
7-3/4 THRU 9-1/4
DIM"A" "B"
DIM"C"DIM FRAME
DEPTH RANGE
Anchor is normally positioned in the center ofthroat to accommodate equal thicknesses ofwallboard at each side of stud. If wall is notsymmetrical, drawings showing condition shouldbe provided.
INSTALLATION SEQUENCE
1. WALL FRAMING2. DOOR FRAME3. WALL SURFACE MATERIAL
16 GAGESTEEL
Shim
All dimensions are in inches, forSI conversion, 1" = 25.4 mm.
Designate if floor anchor or jamb anchor is desired
5-5/8
3/4
CL
CL
1-1/16
STUDSIZE
9/16
7/32 R.
3/41-5/16
4
1/2" BACKBENDS
BEND HERE FOR ONELAYER OF 1/2" > 5/8"
BEND HERE FOR TWOLAYERS OF 1/2" > 5/8"
FOR 2"FACE
18 GAGEGALV STEEL
NOTEFRAME IS SET-UP
AND JAMBS ANCHOREDBEFORE WALLBOARD IS
INSTALLED.
ANCHORS ARE BENT INFIELD TO THICKNESSOF WALLBOARD. IFWALL FRAME WORK ISSET UP BEFORE DOORFRAME, USE ANADDITIONAL JAMB ANCHORAT SILL INSTEAD OFSILL ANCHOR.
STUD
PLACE
BEND
WALLBOARD
WALLBOARD
TAP-IN
WELD TOJAMB
SILL CLIP ATEACH END AND24" O.C.
JAMB
16 GAGESTEEL
2
FACE
Contractorsnaps closureinto placeafter frame isinstalled.
BEFORE DRYWALLSTUD ANCHOR
CLOSURE CLIP
All dimensions are in inches, forSI conversion, 1" = 25.4 mm.
11-512
Ceco Door Products DISTRIBUTOR TECH DATADistributor Tech DataBEFOR DRYWALL STUD ANCHORAND CLOSURE CLIP
1"
3/32"
NOMINAL SIZES
FRAME SPLINES
11-513
SPLINE APPLICATION
8"
Stitchweld
16 Ga. steel
DEPTH FSPAREWORK
3-7/8" or OVER 334
4-3/4" or OVER 434
5-3/4" or OVER 534
6-3/4" or OVER 634
Frame components should have open ends.Mitered corners prevent spline installationwithout modification of backbend.Allot one spline for every 2 feet of impostheight. Drive spline in from ends, locateapprox. equal distance from one another.
For shipping via common carrier,frame size should not exceed8'-0" in more than one dimension.
SPLINE APPLICATION(For Custom Depths)
NOMINAL SIZES
FRAME INSTALLATIONMASONRY AND STUD WALLS
11-901
DOOR OPG AT HEAD
FRA
ME
DEP
TH
JOBSITE STORAGE: Store frames off the ground on wood runners or skids. Do not storedirectly on the ground. Cover frames with tarpaulin or plastic but do insure that adequate
When frames are to be fully grouted and when plaster or mortar contain "anti-freeze" agents,the inside of the frames should be coated with a bituminous, water-resistant paint by theinstallation contractor.
ventilation is provided to eliminate moisture condensation.
Typical wood spreader must be square and madefrom lumber at least 1" thick. Length of spreaderequals door opening width at the head. Cut clear-ance notches for frame stops as shown. Spreadermust be nearly as wide as frame depth for properinstallation.
The installer should use wood spreaders (asdescribed at right), a carpenters level (thelonger the better), and a carpenters square(the bigger the better). Set the frame inthe desired location. Level head and plumbjambs. Shim under jambs if necessary.
SLOTS FORCORNER TABS
CORNER TABS BEND CORNER TABSTOWARD INSIDE OFFRAME
SLOTS FORJAMB TABS
BEND JAMB TABSTOWARD OUTSIDEOF FRAME
JAMB TABS
HEAD JAMB
CORNERASSEMBLY
Install rubber silencers beforeframe is setup to avoid groutplugging holes.
ASSEMBLY of FRAME
SQUARING THE FRAME SPREADER
PLUMBING FRAME
90˚
NOMINAL SIZES
FRAME SPREADER BARS
11-903
This bar is not to be used for installation. A wood spreader is to be used for maintainingproper spacing between jambs. (See the DHI publication "The Installation of CommercialSteel Doors and Steel Frames", "Insulated Steel Doors in Wood Frames", and "Builder'sHardware").
3. SPREADER BAR QUANTITY AND LOCATION
A. All single rabbet frames and double rabbet, single swing frames with depth not exceeding 6 inches: attach (1) spreader bar to the door rabbet. (See Fig. #1)
B. All double rabbet, double swing frames or double rabbet, single swing frames with depth exceeding 6 inches: attach one (1) spreader bar to each frame rabbet (two total).
(see Fig. #2)
4. SPREADER BAR ATTACHMENT
Verify spreader bar length by checking to see that said length is equivalent to the door opening width dimension at head. Place the spreader bar at the bottom of the door opening and tack weld in place. Strength of welds should be such that spreader bar remains in place during transit and also be such that the spreader bar can be removed when required (by means of a sharp hammer blow) without incurring frame damage.
1. SPREADER BAR PROFILE 2. SPREADER BAR LENGTH
Length of spreader bar is equivalent to door opening width dimension.
Fig. #1
DOOR RABBET
SPREADER
JAMB
JAMBSPREADERS
BOTH RABBETS
Fig. #2
X X
X X X
XXX X X
XXXX
X