Embed Size (px)
Citation preview
Doc. No. MK600
SUBJECT: EarlySense User Guide – USA (FDA) version
REV. REVISION DESCRIPTION ECO
NO.
DATE NAME
7
8
Added the need that cable of sensor to be
connected from back of the bed. – for
safety purposes
Changed pictured and changed labels,
class A EMC
ECO-11-12
Feb. 2, 2011
April 2011
Dalia Argaman
Dalia
9 Software ver. 3.0.13 ECO-11-21 June 2011 Shiraz
10 Clarifying “children” definition, updated
cleaning and disinfection procedure and
changing “EverOn” to “EarlySense
System”
ECO-12-01 Dec 2011 Shiraz / Dalia / Aya
11 Change name of device to EarlySense
(Labels with the new “EarlySense” logo)
ECO-12-13 April 2012 Shiraz
NAME DATE SIGNATURE
Written by: Shiraz Levkovich
Appr. Marketing Maayan Wenderow
Appr. Product
manager
Roman Karasik
Appr. Clinic., Regul. Dalia Argaman
Appr. QA Asaf Grosgold
EarlySense Ltd.
12 Tzvi St., Ramat Gan, Israel
Proprietary and Confidential
CONFIDENTIALITY NOTICE
This document contains valuable trade secrets and confidential information of EarlySense Ltd.
Nothing herein may be copied, reproduced or distributed in any form or any medium, or
disclosed to any third party in any manner, without prior written authorization of EarlySense.
The EarlySense System
(EarlySense Model 1.0 - Equivalent to model EverOn 1.0)
User Guide
i
EarlySense Ltd.
EarlySense 1.0
User Guide Revised April, 2012
SW Version: 3.0.13
Document Num. MK-600 Revision Ver. 11
COPYRIGHT 2011 EARLYSENSE LTD. ALL RIGHTS RESERVED WORLDWIDE THIS MANUAL IS
PROPRIETARY TO EARLYSENSE LTD. UNAUTHORIZED USE, DISCLOSURE OR REPRODUCTION IS
PROHIBITED
EARLYSENSE TECHNOLOGIES ASSUMES NO RESPONSIBILITY FOR ERRORS THAT MAY OCCUR IN
THIS MANUAL. EARLYSENSE LTD RESERVES THE RIGHT TO MAKE CHANGES WITHOUT NOTICE
TO THIS EVERON MANUAL, ALSO REFERRED TO AS “THE EARLYSENSE SYSTEM”,AND THE
PRODUCTS DESCRIBED HEREIN.
Contact EarlySense at:
EarlySense Ltd.
European Representative MedNet GmbH Borkstrasse 10 48163 Münster, Germany Phone +49 251 322660 Fax +49 251 3226622
Israel
EarlySense Ltd.
12 Tzvi St.,
Ramat Gan 52504, Israel
Web-site: www.earlysense.com
USA EarlySense Inc. 135 Beaver Street,
Suite 211, Waltham, MA 02452
Phone: (781) 373 3228 E Mail: [email protected] Support Telephone:
East Coast - (617) 800-6668
West Coast - (818) 370-7748
Web-site: www.earlysense.com
ii
Table of Contents
1 Introduction ....................................................................................................................... 1
The EarlySense System Bedside Monitor ........................................................................................... 1
About This Manual ............................................................................................................................... 2
Manual Conventions ............................................................................................................................ 2
Menus Screens and dialog boxes ............................................................................................................. 2
Warnings, Cautions and Notes ................................................................................................................. 3
Terms ................................................................................................................................................... 3
2 Safety ................................................................................................................................. 4
General Safety Guidelines ................................................................................................................... 4
General Hazards .................................................................................................................................. 4
Electrical Shock ........................................................................................................................................ 5
Defibrillation .............................................................................................................................................. 5
Electric Magnetic Interference .................................................................................................................. 5
WiFi Communication ................................................................................................................................. 5
Electrical Fire ............................................................................................................................................ 5
Classification ........................................................................................................................................ 5
Intended Use ........................................................................................................................................ 6
Contraindications for Use ..................................................................................................................... 6
Warnings and Cautions ........................................................................................................................ 6
System Labels...................................................................................................................................... 9
Bedside Unit Label.................................................................................................................................... 9
Sensing Unit Label.................................................................................................................................. 10
System Packaging Label ........................................................................................................................ 10
Explanation of System Labels ................................................................................................................ 11
Compliance with Standards ............................................................................................................... 12
How the Bedside Unit is supplied ...................................................................................................... 12
3 System Description ........................................................................................................ 13
System Components .......................................................................................................................... 13
Sensor .................................................................................................................................................... 13
Sensor Extension Cable ......................................................................................................................... 13
Bedside Unit Controls and Indicators ...................................................................................................... 14
Battery ............................................................................................................................................. 16
The EarlySense System’s User Interface and Screens ..................................................................... 17
User Interface ......................................................................................................................................... 17
System Messages and Alerts ........................................................................................................... 18
Screens .................................................................................................................................................. 18
Setting the volume level of the bedside unit (page 32).............................................................................. 21
iii
4 System Operation ........................................................................................................... 22
Overview ............................................................................................................................................ 22
Positioning the Bedside and Sensing Units ....................................................................................... 23
Turning the System On/Off ................................................................................................................ 24
Electrical Failure................................................................................................................................. 24
After Electrical Power is Restored .......................................................................................................... 26
Patient Information (Admit/Discharge) ............................................................................................... 26
Admitting a Patient.................................................................................................................................. 26
Discharging a Patient / Ending a Patient Monitoring Session ("Discharge") ........................................... 31
Pausing a Patient Monitoring Session ............................................................................................... 32
Setting the General Volume ............................................................................................................... 33
Alerts .................................................................................................................................................. 34
Alerts Table ............................................................................................................................................ 35
Multiple Alerts ................................................................................................................................ 36
Alert Triggers .......................................................................................................................................... 37
Alerting Parameters......................................................................................................................... 37
Modifying Alert Thresholds ..................................................................................................................... 38
Audible and Visual Alert Notification ....................................................................................................... 39
Blue Alerts .............................................................................................................................................. 39
Suspending Red and Yellow Alerts......................................................................................................... 40
Disabling and Enabling Alerts ................................................................................................................. 40
Alerts Setup ............................................................................................................................................ 42
Setting Individual Alert Volume and Tone ..................................................................................... 42
Silencing Alerts ............................................................................................................................... 43
Bed Exit .............................................................................................................................................. 43
Configuring the Bed Exit Alert ................................................................................................................. 44
Setting Bed Exit Sensitivity ............................................................................................................ 44
Patient Turn ........................................................................................................................................ 45
Setting the Patient Turn Interval ............................................................................................................. 45
Starting the Patient Turn Counter ........................................................................................................... 45
Documenting Patient Turn and Resetting Counter ................................................................................. 46
Air Mattress ............................................................................................................................................ 47
Patient Movement .............................................................................................................................. 48
Low Patient Movement Alert ................................................................................................................... 48
Patient Motion Detection ......................................................................................................................... 49
Recording and Viewing Events .......................................................................................................... 50
Manually Recording an Event ................................................................................................................. 50
Trends ................................................................................................................................................ 51
Trends Graph ......................................................................................................................................... 51
Alert Symbols ................................................................................................................................. 54
Event Symbols ................................................................................................................................ 55
Setting the Time Scale .................................................................................................................... 56
Analysis .................................................................................................................................................. 56
iv
Settings .............................................................................................................................................. 57
Brightness ............................................................................................................................................... 57
Choosing a Language ............................................................................................................................. 57
Maintenance ........................................................................................................................................... 58
Reports ............................................................................................................................................... 59
Generating Reports (Data Retrieval) ...................................................................................................... 59
Downloading Patient Data and Reports .................................................................................................. 59
5 Specifications, Maintenance and Troubleshooting ...................................................... 63
Specifications ..................................................................................................................................... 63
Physical Characteristics .......................................................................................................................... 63
Performance ........................................................................................................................................... 64
Electrical ................................................................................................................................................. 64
Operating Conditions .............................................................................................................................. 64
Storage and Transportation Conditions .................................................................................................. 64
Maintenance and Cleaning ................................................................................................................ 65
Cleaning and Disinfection of the Bedside Unit ........................................................................................ 65
Cleaning and Disinfection of the Sensing Unit ........................................................................................ 65
Troubleshooting ................................................................................................................................. 66
6 European Representative and Contact Information ..................................................... 67
1
1 Introduction
The EarlySense System Bedside Monitor The EarlySense System (also known as EverOn) is designed for continuous and contact-
free measurement of respiration rate and heart rate when the patient is lying in bed. In
addition the system tracks body motion and monitors patient movement and can notify
users upon patient bed exit .The system displays numerical heart rate, respiration rate and
movement level and graphical data of trends of these parameters.
The system's design allows the operator to adjust the settings of the threshold parameters
and notifies the caregiver when heart or respiration rate averaged over time, passes above
or below predefined limits. The system also allows the health practitioner to document
the changes in the patient's position in bed by recording the event. The system then
verifies the change in position and logs the information. The system also provides an
option to notify the health care practitioner if a specific amount of time has passed since
the nurse last changed the patient's position. The users can decide to activate or deactivate
these notifications.
Providing contact-free, passive monitoring capabilities, with no need for patient
activation or involvement, the EarlySense System enables continuous monitoring of
patients in home, hospital or clinical settings. The data acquired by the System is
continuously logged in a Bedside Unit, thus, when using the System at home, the data
may be later presented, in a time stamped format, for off-line health care practitioner
analysis.
The system includes a Sensing Unit that is placed beneath the bed mattress or between
the mattress and a mattress pad or mattress cover, and a Bedside Unit which sets the
system options and displays the collected data. Monitoring of the patient begins
automatically as soon as the patient enters the bed. The data acquired by the system is
continuously logged in the Bedside unit, thus allowing the data to be presented, in a time
stamped format. The data provided by the system is intended to aid in the evaluation
process of a patient's clinical status and should be interpreted by a health care practitioner
only.
2
Note
The EarlySense System has not been studied on any specific patient
group, neither has it been studied as a diagnostic tool of any
specific disease or medical condition. It is meant as an adjunctive
tool only for measuring respiratory rate, heart rate and movement
rate.
About This Manual This manual provides the information necessary to operate the EarlySense system in a
safe and efficient manner. Please read the manual thoroughly and understand its contents
before operating the system. If any part of this manual is not clear, contact EarlySense
Customer Support for clarifications.
The manual is intended to serve as an accompanying document to the EarlySense system.
It is not intended to replace the users training course.
This manual should always accompany the unit, and all personnel operating the unit must
be aware of its location.
Manual Conventions The following manual conventions are used throughout the manual.
Menus Screens and dialog boxes
The names of menus, screens and dialog boxes are presented in bold
3
Warnings, Cautions and Notes
Warnings, Cautions and Notes are used throughout this manual:
Warning
A warning indicates precautions and instructions which, if not
followed may result in serious bodily injury or death
Caution
A caution indicates instructions, or cautionary notes which, if not
followed, may result in a damage to the equipment or to the quality
of measurements
Note
Notes contain helpful information and tips
Terms
HR Heart Rate
RR Respiratory Rate
4
2 Safety
General Safety Guidelines
Warning
US Federal Law restricts this device to sale by or on
the order of a physician.
The data acquired by the EarlySense System should
be interpreted by a health care professional only.
• Handle the Bedside Unit with care. Do not drop, knock, or shake the Bedside
Unit. Rough handling can damage the internal circuit boards.
• The System is intended for indoor operation only.
• A damaged system should not be disposed of as unsorted municipal waste.
Contact your local distributor for unit disposal.
• Changes or modifications not expressly approved by EarlySense Ltd. could affect
the safety or effectiveness of the EarlySense System and void the system's
warranty.
• The EarlySense Sensing Unit should be used only with the EarlySense Bedside
Unit, and the EarlySense Bedside Unit should be connected only to the
EarlySense Sensing Unit.
• The EarlySense Bedside Unit is continuously operated equipment with water-
proof splash sensor (IPX4).
General Hazards • Do not use a damaged System. Use of damaged components might result in
malfunctioning of the System.
• The EarlySense System should be installed and serviced only by qualified service
personnel, authorized by EarlySense Ltd.
5
Electrical Shock
The system contains no user serviceable parts. Do not open the system covers.
The Bedside Unit is not waterproof. Keep the Bedside Unit dry to avoid electrical shock
or malfunction.
Defibrillation
The system is Defibrillation proof Type BF applied part.
Electric Magnetic Interference
This equipment complies with IEC EN 60601-1-2:2001 for electromagnetic compatibility
for medical electrical equipment and/or systems. This standard is designed to provide
reasonable protection against harmful interference in a typical medical installation.
However, because of the proliferation of radio-frequency transmitting equipment and
other sources of electrical noise in healthcare and other environments, it is possible that
high levels of such interference due to close proximity or strength of a source might
disrupt the performance of this device. Medical electrical equipment needs special
precautions regarding EMC, and all equipment must be installed by qualified service
personnel.
WiFi Communication
The system incorporates an off-the-shelf certified Wifi communication card (complies
with FCC part 15)
Electrical Fire
Avoid placing liquids or food on any part of the System. Do not allow conductive fluids
to leak into the active circuit components of the System as this may cause a short circuit,
which could result in an electrical fire. In such an event, only fire extinguishers approved
for use on electrical fires should be used. The device is not intended for use in the
presence of flammable mixtures.
Classification Mode 1: The unit is classified as Class I
6
Mode 2: The unit is internally powered, continuously powered, ordinary portable
equipment with applied part (IPX4).
Only equipment specified in this manual and complying with requirements of EN60601
should be connected to the system
The system complies with IEC 60601-1, IEC 60601-1-2 and IEC60601-1-4 EMC class A
device.
Intended Use The EarlySense system is intended for continuous measurement of respiration rate, heart
rate and movement, in an automatic contact-less manner, at home, hospital or clinic
setting. The system is indicated for use in children, adolescents and adults. The operation
of the EarlySense System has been studied in children (weight ≥ 10 Kg) and adults
(weight ≤111 Kg) during sleep and resting condition.
Note
Definition of Age for Children: Children aged 2 and above
Contraindications for Use The EarlySense System is contraindicated for use in:
• Patients in whom proper positioning cannot be achieved or maintained.
• Patients who do not meet the weight limits tested or specified.
• Situations where a dry environment cannot be ensured.
• An MR environment
• An explosive atmosphere or in the presence of flammable anesthetics or gases
Warnings and Cautions • The EarlySense System should be installed and serviced only by qualified service
personnel, authorized by EarlySense Ltd.
• Mounting bed-side unit to the wall should be performed while exercising out-
most caution. DO NOT place the bed-side unit over patient’s head, to avoid
safety related conditions.
7
• Mounting of bed-side unit to the wall should be performed by mechanical experts
of the institution (e.g., Biomed/ engineering), to make sure safe attachment.
EarlySense is not responsible for any harm or damage related to wrongful
placement of the bed-side unit
• Implementation of the nurse call connector option provided in The EarlySense
Bedside Monitor requires coordination between the hospital and EarlySense. Do
not implement this option without consulting with, and receiving approval from,
the hospital administration.
• The data acquired by The EarlySense System should be interpreted only by a
health care practitioner.
• In the event that the EarlySense System does not operate properly, contact
EarlySense Ltd. customer support: (617) 800-6668 (for the east coast) or (818)
370-7748 (for the west coast).
• Never open the Bedside Unit housing as this may damage the System. Refer all
servicing to an authorized technician.
• Only equipment specified in this manual and complying with requirements of
EN60601 might be connected to the system.
• Measurements may be affected by cable lengths. Shorten or extend the lengths
only according to the manual’s direction.
• Changes or modifications not expressly approved by EarlySense Ltd. could affect
the safety or effectiveness of the EarlySense System and void the System's
warranty.
• The System should be operated within a temperature range of 10-35°C (50-95 °F)
for the Bedside Unit, and 5-40°C (41-104 °F) for the Sensing Unit, and within a
relative humidity of 30-80%, non condensing.
• Do not use a damaged System. Use of damaged components might result in
malfunctioning of the System.
• Avoid placing liquids or food on any part of the System. Do not allow conductive
fluids to leak into the active circuit components of the System as this may cause a
short circuit, which could result in an electrical fire. In this event, only fire
extinguishers approved for use on electrical fires should be used. Care should be
taken for patients with poor bladder functioning or control, including small
children, when an EarlySense sensor is placed under their mattress.
8
• Do not share the bed with another person or pet during EarlySense System
recording session. Sharing the bed could affect the effectiveness of the system
and the accuracy of the measurements.
• Avoid using heating blankets. Use of heating blankets could affect the safety or
effectiveness of the EarlySense System and void the System's warranty.
• Do not use the EarlySense System for patients who weigh more than 200 kg (440
Pounds). Usage of the System for such patients might result in malfunction of the
Sensing Unit.
• The patient should not have a direct contact with the Sensing Unit. A mattress,
mattress pad or mattress cover should be always placed as a barrier between the
Sensing Unit of the EarlySense System and the patient. Patients should be
frequently checked to insure direct contact does not occur.
• Careful oversight should be provided when the EarlySense System is used with
children.
• As with all medical equipment, carefully route cables and connections to reduce
the possibility of tripping, entanglement or strangulation.
• Do not create sharp bends in the cable, as this may tear or break the shielding.
Warning
The EarlySense System is not intended for monitoring high risk
situations where ECG monitoring is required. The most reliable
method of patient monitoring combines close personal surveillance
with correct operation of the monitoring equipment.
! Caution: US Federal Law restricts this device to sale by or on the order of a
physician.
9
System Labels
Bedside Unit Label
Figure 1: Bedside Unit Label
Incorporates WiFi module
FCC ID: PD9WM3B2200BG
10
Sensing Unit Label
Figure 2: Sensing Unit Label
System Packaging Label
Figure 3: Packaging Label
11
Explanation of System Labels
The following provides a description of the graphical symbols that appear on the
EarlySense System components and package.
!
Caution/Warning
Consult Accompanying documents
Defibrillation proof, type BF, IPX4 applied part
Fragile, handle with care
Keep dry
Indoor operation only
Sorted disposal
12
Compliance with Standards The EarlySense System was tested and found to be in compliance with the following
standards:
How the Bedside Unit is supplied The EarlySense System is shipped in a protective package containing the following
components:
• 1 Control Unit (Bedside unit)
• 1 Sensor
The System should be unpacked and installed only by an authorized EarlySense
technician.
STANDARD #
1. Medical electrical equipment- general requirements
for safety. Part 1: General Requirements for Safety IEC 60601-8
(2006)
2. Medical Electrical Equipment - Part 1: General
Requirements for Safety; Electromagnetic
Compatibility -- Requirements and Tests
EN/IEC 60601-1-2
(2005)
13
3 System Description
System Components The system consists of a Sensing Unit and a Bedside Unit connected by a cable.
1.Bedside Unit
2. Sensor
Figure 4: The EarlySense System Components
Sensor
The Sensor is placed under the mattress (See Positioning the Bedside and Sensing Unit,
page 23) and detects a signal generated by the patient's breathing, heartbeat and motion.
The sensor’s cable, which should be connected to the bedside unit, is three-meter long.
Sensor Extension Cable
Only if required, an optional two-meter extension cable for the sensor is available.
Note
Use only one extension cable per sensor.
1
2
14
Bedside Unit
The Bedside Unit shows system status, displays the heart rate, respiration rate, movement
level, patient turns and bed exit data, and allows system configuration.
1. Alert indicator key that can be
pressed as a response to an active
alert
2. On/Off
3. Suspend alerts for 15 minutes
4. Download reports
5. Speaker/ buzzer
Figure 5: Bedside Unit Indicators and Keys
Bedside Unit Controls and Indicators
The Bedside Unit contains the following controls and indicators:
1. Alert indicator key - the light will flash red in case of red alerts (e.g. heart rate,
respiration rate and bed exit), yellow in case of yellow alerts (movement and patient turn
reminder) and blue in case of technical alerts. While an alert is active, alert light key can
be pressed to respond to the alert.
2. ON-OFF button. Use the button to switch the bedside unit ON or OFF.
3. 15 min Suspend Key – Pressing it will disable the red and yellow alerts for 15 minutes.
No red or yellow alert will be given by the EarlySense System during the next 15
1
2
3
4
5
15
minutes after this action! Alert symbols on the screen will turn into a Timer (see Figure
6) to notify of this temporary suspension mode. Pressing the Suspend key button again
turns the alerts back on. Blue alerts cannot be suspended under any circumstances.
Figure 6: Suspension Timer
4. Download Reports Key – password will be required
1. USB Connector
2. Nurse Call Connector
3. Sensor Connector
4. Network Connector
Other connectors (for future use) are
clearly labeled as not in use.
Figure 7: Bedside Unit - Side View
1
2
3
4
16
Note
The nurse call in the EarlySense System is a UL1069 compliant
nurse call relay closure connector – Supplementary Device
The EarlySense bedside unit can interface with the existing nurse
call systems found in the hospital., though the actual connection to
the nurse call system requires the support of the Hospital
Biomedical Engineering department
Battery
The system is internally powered by a lithium polymer rechargeable battery that provides
power in case of a power failure (See Electrical Failure, page 24). The battery is not
intended to be replaced by the operator. In standard operating mode, the battery is
designed to allow approximately 30 minutes of operation while the unit is unplugged
from the Electrical Outlet, or in case of power failure.
The battery is automatically recharged by the system. In case the battery no longer
maintains the necessary charge, it must be replaced by an EarlySense authorized
technician. Contact EarlySense technical support.
Note
The system batteries will function when the system is unplugged. In
order to maintain the batteries adequately charged, make sure that
the system is always plugged in to the Electrical outlet during
routine operation.
Sorted Disposal
Do not discard this product. Contact your local authorized representative for additional information for collection and recovery programs available for this product and for appropriate facilities for recovery and recycling
17
The EarlySense System’s User Interface and Screens
User Interface
Interaction with the user interface is via touch screen. Touching some functions (Such as
the Discharge and Trends buttons) will open additional screens, while other buttons
will open additional adjustment functions in the Home screen (Such as Patient Turn q
and Bed Exit sensitivity level). For any interaction, the screen must be unlocked by
touching the lock image in the upper left corner of the Home screen. If the user attempts
to press the touch screen while the system is locked, the lock in the upper left corner will
show a red flash.
18
System Messages and Alerts
There are four types of system messages and alerts:
List of messages/alerts in this category Example
High/Low HR
High/Low RR
Patient Signal Lost
Bed Exit
Patient Out of Bed
Extremely High Motion
Patient Turn is OFF – Low Patient
Movement
Patient Turn is OFF – Air Mattress
Motion Detected
Turn Counter Exceeded
Technical Alert – indicates that there is a
technical problem with the system:
Check Sensor
No AC Power
Very Low Battery
System Malfunction
Functional Message - Informative
message.
Screens
The Home Screen displays the monitoring data and provides access to additional menus.
Choices are selected by touching the screen.
19
1. Lock/Unlock status
2. Nurses details ( Name, Ext.
Number and assigned color
3. Patient details (ID, Room and
Bed numbers)
4. Date/Time
5. Battery status/AC indicator
6. Pause
7. Admit /Discharge patient
8. Enable/Disable heart rate alerts
9. Settable "High" HR threshold
10. Current heart rate
11. Settable "Low" HR threshold
12. Enable/Disable RR alerts
13. Settable "High" RR threshold
14. Current respiratory rate
15.Settable "Low" RR threshold
16. Enable/Disable movement alerts
17. Current movement level (0, Low, Medium, High, Extremely High)
18. Enable/Disable out of bed alert
19. Bed Exit Settings
20. Enable/Disable Patient Turns Counter
21. Patient Turn Counter: Time passed since last turn documented by nurse
22. Patient Turn Protocol Settings (q# - the counter time setting: 1 Hour, 2 Hours, 4 Hours, 6
Hours) indicating the number of hours between each reminder.
20
23. Clock time of last self movement
24.Operational buttons - to open additional screens
Figure 8: Home Screen
The following menus are accessed from the bottom of the Home Screen.
Menu Use For
Adding an event (See Recording
and Viewing Events, page 50).
21
Viewing trends (See Trends,
page 51)
Setting or deactivating Alerts
(See Alerts, page 34).
Setting the volume level of the
bedside unit (page 32)
Access advanced functions
22
4 System Operation
Overview The EarlySense System is designed to display and log respiration rate, heart rate and
movement parameters in an automatic contact-free manner when the patient is lying in
bed. The System is indicated for use in indoor environments. Monitoring of the patient
begins automatically as soon as the patient gets into bed.
The system design allows the user to set high and low threshold parameters that will alert
the user if either heart or respiration rate have crossed predefined thresholds. The system
can alert the user if patient leaves the bed (bed-exit) and allows the healthcare practitioner
to document that s/he changed patients’ position in bed. The health-care practitioner can
insert the event of patient's change of position by documenting the event on the
EarlySense bedside screen. The system then verifies the change in position and logs the
information. The system also provides an option to notify the user if a certain amount of
time (as set by the user) has passed since last position changing (timer expired). The users
can decide to activate or deactivate these notifications
Data is continuously presented on the Bedside Unit main screen. The data obtained
during the monitoring period is recorded by the system in order to enable off-line
presentation and data printing.
The Sensing Unit should be placed under the mattress, underneath the patient’s chest area
and the system should be turned on. After approximately 60-120 sec of the patient lying
in bed in resting position, the system will begin displaying the monitored values on the
bedside Unit Home screen.
By entering the patient’s basic information (MRN, Initials) into the system the data will
be transferred to the Central Display Station (if being used). Heart and respiration rates
and patient movement level will be continuously displayed on screen. Heart and lung
icons will blink and the values will appear in white on the screen as long as
measurements of HR and RR are current.
23
If the system cannot detect (or measure) the momentary heart or respiration rate for more
than 1 minute, the last measured result of HR or RR will be displayed on screen in grey
and the blinking heart or lung icon will stop blinking.
Positioning the Bedside and Sensing Units The Bedside Unit should be mounted to the wall beside the patient’s bed. The power
cable should be connected to the power outlet and the short “telephone” cable should be
connected to the monitor from one side and to the sensor cable on the other side. Please
make sure the cable is not trailing on the floor.
Place the Sensing Unit under the patient’s mattress, and locate it underneath the chest
area, horizontally. Position the sensor so the top surface is facing upwards (as marked)
(See Figure 9). Position the cord that connects between the Sensor and the Bedside Unit
so that it comes out from under the mattress from the head of the bed, in order to not
interfere with the movement of the patient in and out of bed. If the sensor is placed on a
metal framework that does not allow solid support for the sensor, please consult your
authorized EarlySense representative.
Warning
If you mount the Monitor to the wall, ensure that the wall-mount is not
placed directly above the patient's bed.
!
Caution
The patient should not be in direct contact with the Sensing
Unit. A mattress, mattress pad or mattress cover should
always be placed as a barrier between the Sensing Unit of the
EarlySense System and the patient.
24
!
Caution
Handle the Bedside Unit with care.
Do not drop, bang or shake the Bedside Unit. Rough handling
can break the internal circuit boards.
Figure 9: Positioning the Sensor and Bedside Units
Turning the System On/Off Turn the EarlySense System "ON" by pressing the On/Off button on the front of the
Bedside Unit (See Figure 5). The Admit Window will automatically appear. After
admitting the patient, the Home Screen will be displayed.
To turn the system off, press the On/Off switch on the front of the Bedside Unit. You will
be asked if you are sure you want to turn the system off. Confirm turning off by hitting
Yes on the touch screen.
Electrical Failure In case of electrical failure, the internal system battery allows the system to function for
approximately 30 minutes.
Check that the problem is not with the system itself by verifying that the power cable is
not damaged and is connected both to the Electrical Outlet and to the Bedside Unit.
25
The battery icon displayed on the main screen indicates the status of the battery and if the
battery is being recharged.
Figure 10: No AC Power Warning
The battery icon displayed on the main screen indicates the status of the battery as
follows:
Green with a lightning
Battery is charged and
connected to a power outlet
Green
Battery is charged but
disconnected from a power
outlet
Orange
System is disconnected from
power outlet, battery is not
charged.
26
Red
Battery is almost empty.
System is about to shut
down.
The lightning symbol on the battery indicates that the battery is charging.
After Electrical Power is Restored
1. Make sure that the system is plugged into the Electrical Outlet.
2. Turn the System On by pressing the On/Off switch on the front of the Bedside Unit
(See Figure 5). The System automatically starts operating, as detailed above (see
Turning the System On/Off – page 24).
The internal battery automatically recharges when the electrical power is restored.
If System operation is not restored, contact EarlySense Ltd. customer support.
Patient Information (Admit/Discharge)
Admitting a Patient
The Admit Patient screen appears every time the system is switched on automatically
and can also be found by touching the Admit button in the upper right corner of the
Home screen.
Monitoring can take place without entering a patient ID / MRN; however it is advisable
to enter a new patient ID before starting the monitoring, otherwise the monitored
information will not be saved and the information will not be transferred to the main
nurses’ station.
1. Choose Admit in the Home Screen. The first Admit Patient screen will open (Figure
11).
Note
Only letters can be entered in the first and last name boxes and only
alphanumeric characters can be entered in the ID box.
27
Figure 11: Patient Admit Screen
2. Insert the patient's name (Letters only), MRN (ID) (Alphanumeric only), room
number (digits only) and bed number (Alphanumeric only). The MRN (medical
record number), Room No. and Bed No. must be entered for the patient to be
admitted. Choose a color to assign the patient to a nurse, in case you are using the
EarlySense Central Display Station (also referred to as “Patient Care Manager”)
3. To advance to the Patient Demographics screen (Figure 12) press Next.
4. To return to the Home screen without admitting the patient press Cancel or Home.
To admit the patient and return to the Home screen press Done. After pressing Done,
two questions regarding the required settings will show (Figure 14: Bed Exit Alert).
Note
The Patient Demographics screen will not open unless a patient
ID / MRN has been entered.
28
Figure 12: Patient Demographics Screen
The following additional fields can also be entered but are not mandatory:
Gender: Choose M or F.
Date of Birth: Enter the patient’s date of birth (Figure 13).
Figure 13: Date of Birth
29
Choose Done to finish admitting the patient, or Cancel to return to the Home screen
without admitting the patient. If after 10 minutes you have not pressed a button the
screen will close automatically without admitting the patient.
5. After pressing Done, you will be asked two setting questions. The first is whether
you want to set a Bed Exit alert for this patient (Figure 14). If you choose Yes, the
Bed Exit alert will be enabled automatically with the default setting of sensitivity
level. If you choose No, the Bed Exit alert will be disabled. After answering the first
question, you will be asked whether you want a Patient Turn reminder for this patient
(Figure 15). If you choose Yes, the Patient Turn Counter will be enabled
automatically with the default setting of a reminder every 2 hours, and if you choose
No, the Patient Turn Counter will be disabled. If after 1 minute you have not pressed
a button the screen will close automatically, the patient will be admitted and the Bed
Exit alert and the Patient Turn Reminder will remain disabled.
30
Figure 14: Bed Exit Alert
Figure 15: Patient Turn Reminder
31
Discharging a Patient / Ending a Patient Monitoring Session ("Discharge")
Warning
To avoid recording patient data under an erroneous
name you must perform the discharge procedure
before beginning monitoring of a new patient.
When the recording session is completed perform the "Discharge" procedure:
1. In the Home screen choose Discharge. The Confirm Discharge screen will open
(Figure 16)
2. Choose Yes.
Figure 16: Confirm Discharge Screen
3. You will be asked if you want to admit a new patient (Figure 17)
32
Figure 17: Admit Confirmation Screen
4. Touch Yes to admit a new patient and No to return to the Home screen without any
patient being admitted.
Pausing a Patient Monitoring Session The Pause button stops the recording session temporarily, while the patient’s
identification and trends are saved. At any time the patient’s recording can be resumed,
and all the previous trends will be displayed as usual. Pause should be used when the
sensor is temporarily disconnected from the bedside unit to avoid a blue ‘Check Sensor’
technical alert from sounding, this function should be used for example when the patient
needs to be transported with his/her bed and the sensor needs to be disconnected from the
Bedside unit.
To pause the recording session:
1. Press the Pause button at the Home screen (See Figure 8). A Pause screen will be
displayed (Figure 18).
33
Figure 18: Pause Screen
2. To continue the recording session, press Resume at the Pause Screen (Figure 18).
Setting the General Volume The General Volume sets the volume of all alert tones. In addition volumes and tones for
individual alerts can also be set (See Alerts Setup
Setting Individual Alert Volume and Tone, page 42). Note that the alert volumes are
determined by which of the two parameters (General or Alert) was set last and that the
default setting for the alerts in the bedside unit is mute. At startup and when admitting a
new patient following discharge, the system returns to default alert settings.
To set the General Volume:
1. Choose the Volume button from the Home screen. The General Volume box
opens (Figure 19)
Figure 19: General Volume Box
34
2. Push the Plus button to raise the volume or the Minus button to lower the volume.
3. Click OK to confirm
The Volume icon is marked with an X if the volume is set to zero.
Figure 20: Alerts Volume Off Status
Alerts Alerts are used to notify personnel of situations that may require attention. The
EarlySense System enables the user to define upper and lower thresholds for the heart
rate, respiration rate, time out of bed and patient turn. If any of the parameters, as set by
the user, cross these specified thresholds, an audible and visual alert notification is
triggered.
35
Alerts Table
The system uses the following alerts:
Message Color Description
High/Low Heart Rate:___ Red Heart Rate exceeds thresholds.
High/Low Resp. Rate:___ Red Respiration Rate exceeds thresholds.
Bed Exit
Sensitivity Settings:
1 (Low) – 6 (High)
Red Bed Exit
Patient Out of Bed
For ____ Min
Red System detected that patient is out of bed for a time
interval exceeding a preset threshold.
Patient Signal Lost Red System cannot detect patient’s signal.
Check patient and sensor location.
Extremely High Motion Yellow Patient Movement Level has been extremely high
during the last minute.
Patient Turn is OFF
Low Patient Movement
Yellow Patient Movement Level has been very low during
nighttime (00:00-6:00). Consider setting Patient Turn
reminder ON.
Patient Turn is OFF
Air Mattress Motion
Detected
Yellow Air Mattress was detected on the bed. Consider setting
Patient Turn reminder ON.
36
Turn Counter Exceeded
____ Hours
Yellow Threshold time interval for turning the patient expired.
Check Sensor
Reconnect/Replace Sensor
or Restart
Blue Technical alert indicating that the sensor connection is
malfunctioning.
Try to reconnect the sensor and if problem persists
replace the sensor (See Troubleshooting page 66).
No AC Power
Operating on Battery
Backup
Blue An alert indicating that the EarlySense Bedside unit is
disconnected from the electrical power outlet.
Reconnect the EarlySense bedside unit to the
electricity Mains – otherwise the bed-side will
shutdown (See Troubleshooting page 66).
Very Low Battery
System Shutting Down
Blue An alert indicating that the battery is low, and system
is about to shut down.
Reconnect the control unit to the electricity Mains (See
Troubleshooting page 66).
System Malfunction
Please Contact Service
Engineer
Blue
Technical alert indicating that the system is
malfunctioning. User should contact a service engineer
(See Troubleshooting page 66).
Multiple Alerts
Multiple alerts occur when more than one alert is triggered at the same time. For instance
if a blue system malfunction occurs while an elevated HR is in progress, this situation is
defined as a multiple alert.
There can only be one active alert at a time. If an additional alert occurs while an alert is
already active, the system will then determine which alert will be active according to the
following priority:
• Blue
• Red
37
• Yellow
A new alert will become active only if the currently active alert has a lower priority.
Alert Triggers
Default alert status is:
Alert Status
Heart Rate ON
Respiratory Rate ON
Movement ON
Patient Turn counter OFF
Bed Exit OFF
Default alert threshold values are:
Low limit threshold High limit threshold
Heart Rate 40 BPM 130 BPM
Respiratory Rate 8 Br/min 32 Br/min
Patient Turn counter
(default)
2 hours
Bed Exit (default) Immediate – sensitivity 3
Alerting Parameters
Low Heart Rate High Heart Rate
Time to alert for change
in HR
Max. 60 seconds Max 60 seconds
38
Low Respiration Rate High Respiration Rate
Time to alert for
change in RR
Max. 150 seconds Max. 120 seconds
Modifying Alert Thresholds
When beginning to monitor a new patient, it is advisable to set patient specific alert
thresholds. If relevant for a specific patient, Bed Exit alert sensitivity or duration and
Patient Turn interval should be set from the relevant section in the home screen next to
each function setting (see pages. 44 and 45). To change the default HR and RR
thresholds:
1. Touch the upper or lower thresholds in the HR or RR boxes in the Home screen
2. Touch the down-pointing arrow to lower the threshold or the up-pointing arrow
to raise the threshold (Figure 21)
3. When you reach the desired threshold touch the number displayed, or wait.
Figure 21: Adjusting the HR Upper Threshold
39
Thresholds can be set in the following ranges:
Lowest settable limit
threshold
Highest settable limit
threshold
Heart Rate 35 BPM 150 BPM
Respiratory Rate 8 Br/min 44 Br/min
Audible and Visual Alert Notification
When an alert is triggered an audible alert sounds and the corresponding alert parameter
on the monitor main screen will be shown with its background color corresponding to the
alert color, either red or yellow (Blue alerts are not connected to a specific monitoring
parameter). A message will appear on the bottom of the window detailing the nature of
the Alert (Figure 22) and the time passed since alert was raised
Figure 22: Alert Screen
Blue Alerts
Blue alerts are managed differently than yellow or red alerts. Blue alerts cannot be
suspended; their volume is set at maximum and is non-adjustable. Blue alerts appear only
40
with an “OK” button and remain active as long as the alert condition exists. They
disappear only after the technical issue is resolved. The rest of the information in this
section relates to red and yellow alerts only.
Suspending Red and Yellow Alerts
Press the “OK” button to close an active alert (Figure 22). Notice that as long as the alert
condition exists, the alert will show up again. To close an active alert and temporarily
disable for 15 minutes - all red and yellow alerts, press the 15 min Suspend Alert button
(Figure 22). To cancel the 15 min suspension, press twice on the external “Suspend alerts
for 15 min” button (See Figure 5).
Disabling and Enabling Alerts
When beginning to monitor a new patient, it is advisable to set the specific alerts that
should be enabled for this specific patient. By default all alerts apart from the Bed Exit
and Patient Turn alerts are enabled. Per each patient’s condition, the user is advised to
enable Bed Exit or Patient Turn alert as required.
To disable alerts for specific parameters touch the bell symbol next to the alert in either
the Home screen or the Alerts Setup screen. To enable alerts touch the bell symbol
again.
If an alert is disabled while the alert is active, the alert will remain active until it is
suspended by the user.
When the Bed Exit alert is being disabled, the question “Are you sure you want to set bed
exit alert off?”(Figure 23) To disable the alert, choose Yes.
41
Figure 23: Bed Exit Off
When the Patient Turn Counter alert is being disabled, the question “Are you sure you
want to set patient turn alert off?” (Figure 24) To disable the alert, choose Yes.
Figure 24: Patient Turn Off
In case the alerts are disabled for a specific parameter the bell icon for the corresponding
parameter in the main and alerts setup screens will be marked with an X as follows:
42
To suspend all red and yellow alerts for 15 minutes, press the hardware Suspend alerts for
15 min button (Figure 5). Press again the same button to enable alerts.
Alerts Setup
Setting Individual Alert Volume and Tone
Press the Alerts button on the bottom of the Home screen. The Alerts Setup screen will
open (Figure 25). When entering the Alerts Setup screen the current status of all alerts,
as shown in the following list, is displayed:
• Alert volume
• Tone
• Enabled/disabled
Figure 25: Alerts Setup Screen
• Click the plus or minus button to raise each alert volume
• Press buttons 1, 2 or 3 to choose a Tone.
43
• After setting up the alerts, touch Submit to activate these settings or Cancel
to preserve the existing settings.
Note
In addition to changing the individual alert volumes as described
above, you can also change the general volume (See page 32) or by
setting volume and tone of all in the alerts setup screen. The alert
volumes are determined by which of the two parameters (General
or Alert) was set last.
Note
When a patient is admitted or discharged all alert settings will
return to default.
Warning
The Audible alert in the EarlySense System is not intended for
monitoring high risk situations where ECG monitoring is required.
The most reliable method of patient monitoring combines close
personal surveillance with correct operation of the monitoring
equipment
Silencing Alerts
A green bell icon indicates that the alert is active.
Silence alerts volume by setting the alerts volume to zero in either the general alerts
volume icon in the Home screen or in the Alerts Setup screen.
In case the alerts are silenced for a specific parameter the bell icon for the corresponding
parameter in the main screen will be displayed with a mute sign as follows:
Bed Exit The EarlySense System tracks if there is a Bed Exit. This alert is disabled by default.
44
Note
If the patient is allowed to get out of bed without the nurse being
notified, you can disable the Bed Exit alert by touching the bell in
the In Bed section of the Home Screen.
Configuring the Bed Exit Alert
Bed Exit alert can be configured in terms of alert volume and tone (See Setting Individual
Alert Volume and Tone, page 42) and sensitivity.
Setting Bed Exit Sensitivity
Press the Bed Exit Settings button on the lower right of the Home screen. The Bed Exit
Settings Area will open (Figure 26).
Figure 26: the Bed Exit Settings Area
The Bed Exit Alert can be set either to provide an immediate alert when the patient exits
the bed (varying in 6 levels of bed exit sensitivity levels) or to provide an alert when the
patient has been out of bed for a period ranging from 3-20 minutes.
Use the arrows to choose the desired delay or sensitivity setting. After 3 sec the arrows
will disappear and the change will be applied.
• If you want an immediate alert when a patient exits the bed, click the arrows
to choose a sensitivity ranging from 1-6, with 1 being the least sensitive and
6 being the most sensitive. Note that sensitivities 5 and 6 are highly sensitive
and might be triggered due to excessive movements of a patient while in bed.
• If you want the system to alert after a period of time that the patient is out of
bed, choose the time duration you would like between when the patient
leaves the bed, and when the alert sounds. Use the same set of arrows that
you use to set the sensitivity to select the number of minutes for the delayed
Bed Exit alert.
The Bed Exit alert is disabled by default. Enable the Bed Exit alert by pressing the bell
icon.
45
The active mode of the Bed Exit alert is indicated by the bell icon at the Bed Exit section
of the Home screen (Figure 27).
Figure 27: Bed Exit Box
Patient Turn Patient Turn is used to document change of the patient’s positioning in bed and to
produce an alert if the interval set for changing the position has been exceeded (timer
expired). The Patient Turn alert is also disabled by default.
Setting the Patient Turn Interval
The turn interval is referred to as "q". For instance if you would like the system to
generate an alert as a reminder to turn the patient every 2 hours, set q to q2.
To change the time interval between the turn reminders touch the q button in the Patient
Turn box (Figure 28) in the Home screen (Figure 8). Using the arrows, choose the
relevant q number (number of hours). After 3 sec the arrows will disappear and the
change will be applied.
Figure 28: Setting Patient Turn Interval
Starting the Patient Turn Counter
To enable and disable Patient Turn counter touch the Bell Icon in the Patient Turn
section that is in the Home screen. The counter will become enabled (Figure 30). To
disable the counter press the Bell icon again (Figure 29).
46
Figure 29: Patient Turn Box – Disabled Counter
Figure 30: Patient Turn Box – Enabled Counter
Documenting Patient Turn and Resetting Counter
After turning the patient, press Patient Turned within 1 minute from the time that the
patient turn was performed. The system logs the event (Figure 31). In addition, the
system detects the corresponding change in body movement and verifies the event. The
verification will appear in the printed report of the same day (See Reports, page 59)
Figure 31: Recording Patient Turned Event
If the patient turn interval passes without the Patient Turned button being pressed by the
user, a Patient Turn alert will occur (Figure 32) indicating that the counter has exceeded
its time threshold. The alert message will disappear by pressing Ok or by documenting a
patient turn by pressing Patient Turned. If Ok was pressed, but the Patient Turned
button was not pressed within 15 minutes, the alert will go off again.
47
Figure 32: Patient Turn Alert Screen
Air Mattress
If the Patient Turn alert is turned off and the system detects an air mattress in operating
condition, the following alert will appear (Figure 33).
Figure 33: Air Mattress Alert
After you press “OK” you will be asked if you would like a patient turn reminder for the
patient (Figure 34Error! Reference source not found.).
Figure 34: Patient Turn Reminder
In addition, if an air mattress is not detected and a Turn Counter Exceeded alert is
generated, you will be suggested to consider using an air mattress.
48
Patient Movement Movement rates are determined in terms of percentage of movement time within a
defined period of time as described in the following table. The accuracy of the system in
displaying different rates is also presented below.
Rate Percentage of movement
during defined period
Accuracy of rates
displayed
(For adults)
Accuracy of rates
displayed (For children)
0 0 100% 100%
L Up to 40% 100% 100%
M 40-60% 81% 81%
H 60-80% 100% 86%
EH 80-100% 96% 94%
Patient movement over time can be viewed in Trends (See Trends, page 51).
Low Patient Movement Alert
Alerts for movement are displayed in cases of low and extremely high movement. An
alert for Low movement (Figure 35) may come up once a day at 6:00 AM if during the
night (00:00-6:00) the amount of patient movement or activity level was below a certain
threshold, which might imply the patient is in risk for developing pressure ulcers.
Following dismissing the alert of low movement, you will be asked if you want a Patient
Turn reminder for this patient (Figure 34).
49
Figure 35: Low Patient Movement Alert
Patient Motion Detection
In case that the Patient Turn Reminder is being used, and the system detects additional
patient movement during the night – following the first Turn Reminder in the morning
you will be suggested to consider re-evaluating Braden score (Figure 36).
50
Figure 36: Excess Patient Movement Detected
Recording and Viewing Events Occurring events can be noted by the user and entered into the system for documentation
purposes. These events will then appear in the Trends display.
Manually Recording an Event
1. To access the Events menu click Events in the Home Screen. The Events
menu appears (
2. Figure 37).
Figure 37: Events Menu
51
3. Touch one of the four primary events on the left or secondary events on
the right. The button changes color showing that it has been successfully
chosen. The following message appears: Recording Event: <Event
Name>
4. Touch the Home button to confirm your choice and close the screen or
Cancel to cancel your choice.
The following Events are available:
Primary:
• Emerg. Med. – Emergency medication given when patient is in distress
• CPAP/BPAP
• Intubation
• Patient Fall
Secondary:
• Continuous Med. – routine medication
• Pain Relief Med. – pain relief medication
• Patient Agitation
• Skin Breakdown – a situation that may lead to pressure ulcer development
• General Flag 1 – can be used in order to mark any desired event of type 1 which
is not included in the list of events
• General Flag 2 – can be used in order to mark any desired event of type 2 which
is not included in the list of events
Trends Trends are displayed in a graph format.
Trends Graph
To view the Trends Data click the “Trends” button in the lower section of the Home
Screen.
To advance or go back in the time frame press the forward or back arrows.
52
Figure 38: Trends Data Screen
Number Name Description
1 Current heart rate Current heart rate in beats per minute
2 Events Displays events that users have manually entered (for
documented) during the time displayed
3 Respiratory rate Current respiratory rate in breaths per minute
4 Heart rate trends Displays heart rate in beats (graphs) per minute during the
time displayed.
5 Respiration rate
trends
Displays respiration rate (graphs) in breaths per minute
during the time displayed.
53
6 Scroll back Touch here to scroll back.
7 Alerts Displays alerts that occurred during the time displayed
(See Alerts, page 34).
8 Time scale Time scale for data presented
9 Scroll forward Touch here to scroll forward.
10 Movement trends Shows patients movement level while in bed during the
timescale presented (See Patient Movement, page 48).
11 Out of bed Shows the time intervals when patient has been out of bed
(Bed Exit, page 43)
12 In bed Shows the time intervals patient spent in bed
13 Time period buttons
(10 min, 1 hour, 3
hours, 8 hours, 1 day)
Touch one of these buttons to change the time period
displayed in the graph.
14 Analysis screen Open the Analysis screen (Figure 39).
54
Alert Symbols
The following symbols are used in the Trends graph:
Icon Meaning
Blue Alerts —Technical Alerts: System Malfunction, Sensor Malfunction, Low
Battery.
High/Low Heart Rate – Red Alert
High/Low Respiration Rate – Red Alert
Movement Level High/Low – Yellow Alert
Patient Turn Counter – Yellow Alert
Out of Bed – Red Alert
Signal Lost – Red Alert
55
Event Symbols
When entered by the user, the following Event symbols are used in the Trends Graph:
Intubation
Patient Fall
Emergency Medication
Continuous Medication – Routine Medication
Pain Relief Medication
Patient Agitation
Skin Breakdown
General Flag 1 - Can be used in order to mark any desired event of type 1
which is not included in the list of events
General Flag 2 - Can be used in order to mark any desired event of type 2
which is not included in the list of events
Patient Turn – Inserted automatically if a staff member pressed the RESET
on patient turn counter and the system detected that patient turn occurred.
56
Setting the Time Scale
Upon entering the Trends screen, the default time scale displayed is 3 hours. You can
return to this time scale at any time by touching the Default button. Use the buttons
under the graph to determine the time scale displayed. If you choose a larger time scale
the current time that is in the center of the time scale will remain the center. If you choose
a shorter time scale you will be prompted to touch the screen to determine where you
would like to center the displayed timescale.
Analysis
The Analysis function allows you to see the average respiration, heart rate and movement
time percentage for a specified interval each day. Touch the Analysis in the trends screen
to open the Analysis screen (Figure 39).
Figure 39: Analysis Screen
Use the arrows to set the time slot you want, and then click Show Data. The data will
appear in the table.
57
Settings To access the settings click Settings in the Home Screen. The Settings screen has three
tabs: Brightness, Setup and Maintenance.
Brightness
In the Brightness tab (Figure 40) Press the “-” to darken the screen, and press the “+” to
brighten it.
Please note that if the brightness level is set to the lowest level, the screen might be seen
as black in daylight. Touching the screen while brightness is set to the lowest level will
change the brightness to a higher level, in order to be able seeing buttons and labels and
enabling adjustment of brightness to higher level manually.
Figure 40: Brightness
Choosing a Language
In the Setup tab (Figure 41) choose the desired language to be used in the system
interface and click Done.
58
Figure 41: Setup Tab
Maintenance
This mode should be used only by a technician authorized by EarlySense Ltd.
Entering the technician mode requires a password. To access the Technician mode, press
the Maintenance tab (Figure 42).
Figure 42: Maintenance Tab
59
Reports
Generating Reports (Data Retrieval)
Data analysis may be performed on-line during the monitoring session based on the
bedside unit display or reports.
Reports to be printed may be downloaded at the bedside unit or at the Central Display
Station (See EarlySense Central Display Station manual). To ensure the privacy of the
patient's medical data a PIN must be entered before reports can be downloaded.
The data can be downloaded as CSV file and as a complete report in Acrobat PDF
format. In case of CSV file the data can be viewed by the physician using standard
available software e.g., Microsoft Excel. The data is presented numerically; any other
desired graph can be generated by the physician, based on the data. The PDF report
includes both numerical and trend vs. time graph that can also be printed and includes
information about Heart and Respiratory rates as well as patient's movement, in/out of
bed status, alerts history and patient turns (See Figure 45 for an example).
Warning
The data acquired by the EarlySense System should be
interpreted by a healthcare practitioner only
Downloading Patient Data and Reports
1. Insert a flash drive with at least 0.5 GB of free space into the USB slot. (If the
flash drive is already inserted it must be removed and re-inserted before
commencing the data download procedure).
2. Press the Download Report button (See Figure 5) on the front panel.
3. You will be prompted to insert a PIN (Figure 43) and click Submit. A message
will appear on the bottom of the screen informing you that downloading has
commenced (Figure 44)
60
Figure 43: PIN Window
Figure 44: Downloading Message
4. The system will automatically download the data (CSV file) and the report for
(.PDF) file of the last 2 admitted patients.
5. A message is displayed when the download is completed.
61
62
Figure 45: Example of Printed Report (PDF File)
63
5 Specifications, Maintenance and Troubleshooting
Specifications
Physical Characteristics
Sensing Unit Bedside Unit
Dimensions
300 x 210 x 2.5 mm 250 x 260 x 110 mm
Weight
160 g 3.0 kg
Materials
ABS + Poly carbonate ABS + Poly carbonate
64
Performance
Respiration Rate Heart Rate Movement
Range 6 – 45 Br./min 30 - 170 BPM* 0, L, M, H, EH
Averaging Period
1 Min. 1 Min. 15 seconds
Accuracy
±4% or ±1.5 Br/min, whichever is
greater
±4% or ±5 BPM,
whichever is greater
• The System detects heart rate that is > 1.8 times the respiration rate
• Total system accuracy including undetected signals 90% for RR and for HR. The total system
accuracy was measured as +/- 10% of the predicate device
Alert Thresholds
Default: Low=8 Br./min ; High=32
Br./min
Default Alert: Low=40
BPM ; High=130 BPM
Default: Low = 0%
High = "Extremely-High"
movement > 1 minute
Min- Max settable Alert Thresholds
Low: 8 Br./min ;
High: 44 Br. / min
Low: 35BPM
High: 150 BPM
Electrical
Voltage Input Range 100-240 VAC, 50-60 Hz, 0.9A max Battery Rechargeable battery Fuses 2 x 1 Amp Isolation Medical grade isolation between the Bedside Unit and the power supply
Operating Conditions
Relative Humidity 30% - 80% non condensing Ambient Operating
Temperature Bedside Unit: 10- 35 °C (50-95 °F) Sensing Unit: 5- 40°C (41-104 °F)
Storage and Transportation Conditions
Temperature Range 0-50 °C (32-122 °F) Relative Humidity 10%-90% non condensing
65
Maintenance and Cleaning The EarlySense System is designed to provide a trouble-free and maintenance-free
operation. The only maintenance required is to keep the System clean and dry, and to
verify that there is no physical damage to the Bedside Unit and to the Sensing Unit.
The sensing unit should be replaced on an annual basis to ensure proper functionality of
the system.
Cleaning and Disinfection of the Bedside Unit
Gently wipe the exterior of the Bedside Unit using soft, slightly damp cloth / wipes
containing anti-septic substances. Wipes containing alcohols, Chlorohexidine, and bleach
material with concentration up to 5% can be used. Avoid excessive liquids.
Cleaning and Disinfection of the Sensing Unit
Gently wipe the Sensing Unit using a soft, slightly damp cloth / wipes containing anti-
septic substances. Wipes containing alcohols, Chlorohexidine, and bleach material with
concentration up to 5% can be used). Please ensure that the sensor is dry before re-use.
Avoid excessive liquids.
!
Caution
Avoid placing liquids or food on any part of the System. Do not allow
conductive fluids to leak into the active circuit components of the System
as this may cause a short circuit, which could result in an electrical fire. In
such an event, only fire extinguishers approved for use on electrical fires
should be used.
!
Caution
• Never open the Bedside Unit housing as this may damage the system.
• Handle the Bedside Unit with care. Do not drop, knock, or shake the
Bedside Unit. Rough handling can damage internal circuit boards.
66
Troubleshooting
Problem Possible Cause Solution
The system is
functioning but the AC
icon is not displayed on
the battery icon
System is unplugged
from the Electrical
Outlet
Reconnect the unit to the Electrical Outlet.
Screen is dark but LEDs
are on
The screen was set to
be darkened
or
Technical problem
Touch the screen once, it will become brighter. To
changes the brightness press the button Settings (see
page no. 57).
Turn off the system by pressing the On/Off switch for
10 seconds, and then turn the system back ON by
briefly pressing the On/Off switch. If problem is not
resolved call your service engineer
Blue Alert is On
"System Malfunction”
Message
System Malfunction Contact a service engineer.
Blue Alert is On
"Check Sensor"
Message
Bedside Unit has
detected that the
sensor is not
connected
• Check if the sensor is connected to bedside Unit.
Reconnect if necessary.
• If problem persists, replace sensor
• If problem persists, restart system
• If problem persists, call your service engineer
Blue Alert is On
"Low Battery” Message
System is unplugged
and battery is
discharging
• Reconnect Bedside Unit to the Electrical Outlet.
Bedside Unit is not
responding (ON /OFF is
not possible)
No electrical power
as system is
unplugged and
battery is discharged
or,
System error.
• Check connection to the electrical Power
• Reconnect if necessary.
• If problem persists, call the service engineer.
The Bedside Unit is
operating but no HR or
RR is displayed.
Difficulty in
detecting a signal
• Check sensor location. The sensor should be
placed under the mattress below the patient's chest
area, horizontally.
• Reposition the sensor if it moved from the
specified location. If the problem persists, replace
the sensor.
67
6 European Representative and Contact Information
Contact EarlySense at:
European Representative MedNet GmbH Borkstrasse 10 48163 Münster, Germany Phone +49 251 322660 Fax +49 251 3226622
Israel Headquarters EarlySense Ltd. 12 Tzvi St., Ramat Gan 52504, Israel Website: www.earlysense.com
USA Headquarters EarlySense Inc. 135 Beaver Street,
Suite 211, Waltham, MA 02452
Phone: (781) 373 3228 E Mail: [email protected] Support Telephone:
East Coast - (617) 800-6668
West Coast - (818) 370-7748
