Embed Size (px)
Citation preview
Schedule
SKIM AKREDITASI MAKMAL MALAYSIA (SAMM) LABORATORY ACCREDITATION SCHEME OF MALAYSIA
MS ISO/IEC 17025
Issue date: 22 August 2016 Valid until: 14 September 2019
NO: SAMM 372
Page: 1 of 3
The v
alid
scope o
f accre
ditation is in w
ww
.jsm
.gov.m
y/c
ab-d
irecto
ries.
LABORATORY LOCATION: (PERMANENT LABORATORY)
elab TESTING & RESEARCH CENTER DOSHIN RUBBER PRODUCTS (M) SDN BHD LOT PT 34252, JALAN SEKOLAH RANTAU PANJANG 42100 KLANG SELANGOR
This laboratory accredited under Skim Akreditasi Makmal Malaysia (SAMM) meets the requirements of MS ISO/IEC 17025:2005 ‘General requirements for competence of testing and calibration laboratories’. This Malaysian Standards is identical with ISO/IEC 17025:2005 published by the International Organization for Standardization (ISO). FIELD OF TESTING: MECHANICAL SCOPE OF ACCREDITATION:
Materials/ Products Tested
Type of Test/ Properties Measured/
Range of Measurement
Standard Test Methods/ Equipment/Techniques
Laminated Elastomeric Bearings, Elastomeric Bearing Pads and Strips
Compression Quality Assurance Test (Max. Vertical Load 50,000 kN) (Max. Horizontal Load 5000 kN)
AS 5100: Part 4 (2004) [Appendix D2]
BS 5400-1983 Section 9.2 Clause 7.2 (b) (i)
BS 6177: 1982 Clause 9.3
BS 6177: 1982 Clause 9.4
RMS B281 Clause 2.2.7 (April 2012)
BS EN 1337-3: 2005 (Annex H: Level 1)
Compression Stiffness (Max. Vertical Load 50,000 kN) (Max. Horizontal Load 5000 kN)
AS 5100: Part 4 (2004) [Appendix D3]
BS 5400-1983 Section 9.2 Clause 7.2 (b) (ii)
AASHTO Sec.18 (2003) clause 18.7.4.5.6
AASHTO Sec.18 (2003) clause 18.7.4.5.7
RMS B281 Clause 2.2.4 (April 2012)
RMS B281 Clause 2.2.6 (April 2012)
Schedule
SKIM AKREDITASI MAKMAL MALAYSIA (SAMM) LABORATORY ACCREDITATION SCHEME OF MALAYSIA
MS ISO/IEC 17025
Issue date: 22 August 2016 Valid until: 14 September 2019
NO: SAMM 372
Page: 2 of 3
The v
alid
scope o
f accre
ditation is in w
ww
.jsm
.gov.m
y/c
ab-d
irecto
ries.
FIELD OF TESTING: MECHANICAL SCOPE OF ACCREDITATION:
Materials/ Products Tested
Type of Test/ Properties Measured/
Range of Measurement
Standard Test Methods/ Equipment/Techniques
Laminated Elastomeric Bearings, Elastomeric Bearing Pads and Strips (continued)
Compression Stiffness (Max. Vertical Load 50,000 kN) (Max. Horizontal Load 5000 kN)
RTA B280 Clause 2.2.4 (2011)
BS EN 1337-3:2005 [Annex H: Level 2]
BS 6177:1982 Clause 9.6
Shear Stiffness (Max. Vertical Load 50,000 kN) (Max. Horizontal Load 5000 kN)
AS 5100: Part 4 (2004), [Appendix D4] BS 5400-1983 Section 9.2 Appendix A
BS EN 1337-3:2005 [Annex F.7.2]
BS 6177: 1982 Clause 9.5 (Single Shear Configuration)
BS 6177: 1982 Clause 9.5 (Double Shear Configuration)
RMS B281 Clause 2.2.5 (April 2012)
RTA B280 Clause 2.2.5 (2011)
AASHTO Sec. 18 (2003) Clause 18.7.4.5.8
Structural Bearings (Spherical Bearings and Mechanical Pot Bearings)
Compression Quality Assurance Test (Max. Vertical Load 50,000 kN) (Max. Horizontal Load 5000 kN)
BS EN 1337-5:2005 [Annex B]
AASHTO Sec. 18 (2003) Clause 18.7.2.5
AASHTO Sec. 18 (2003) Clause 18.7.2.6
BS 5400:1983 Sec. 9.2 Clause 7.2 (b)
Compression Stiffness (Max. Vertical Load 50,000 kN) (Max. Horizontal Load 5000 kN)
BS EN 1337-5:2005 [Annex B]
BS 5400:1983 Sec. 9.2 Clause 7.2 (b)
Vertical Load Test (Max. Vertical Load 50,000 kN) (Max. Horizontal Load 5000 kN)
AASHTO Sec. 18 (2003) Clause 18.7.2.5
AASHTO Sec. 18 (2003) Clause 18.7.2.6
Schedule
SKIM AKREDITASI MAKMAL MALAYSIA (SAMM) LABORATORY ACCREDITATION SCHEME OF MALAYSIA
MS ISO/IEC 17025
Issue date: 22 August 2016 Valid until: 14 September 2019
NO: SAMM 372
Page: 3 of 3
The v
alid
scope o
f accre
ditation is in w
ww
.jsm
.gov.m
y/c
ab-d
irecto
ries.
FIELD OF TESTING: MECHANICAL SCOPE OF ACCREDITATION:
Materials/ Products Tested
Type of Test/ Properties Measured/
Range of Measurement
Standard Test Methods/ Equipment/Techniques
Structural Bearings (Spherical Bearings and Mechanical Pot Bearings)
Horizontal Load Test (Max. Vertical Load 50,000 kN) (Max. Horizontal Load 5000 kN)
BS 5400:1983 Sec. 9.2 Clause 7.2 (b) AASHTO Sec. 18 (2003) Clause 18.7.2.9
Seismic Bearings (Structural Isolation, e.g. HDRB, LRB and Pendulum)
Compression Quality Assurance Test (Max. Vertical Load 50,000 kN) (Max. Horizontal Load 5000 kN)
BS EN 15129: 2009 Clause 8.2.1.2.6 Compression Under Zero Lateral Displacement
BS EN 15129: 2009 Clause 8.2.1.2.7
Compression Stiffness (Max. Vertical Load 50,000 kN) (Max. Horizontal Load 5000 kN)
BS EN 15129: 2009 Clause 8.2.1.2.8
Horizontal Capacity (Max. Vertical Load 50,000 kN) (Max. Horizontal Load 5000 kN)
BS EN 15129: 2009 Clause 8.2.1.2.5 Horizontal Characteristic on Repeated Cycling
Note: AASHTO: American Association of States Highway and Transportation Office. RTA: Roads and Traffic Authority. RMS: Roads and Maritime Services. HDRB: High Damping Rubber Bearing LRB: Lead Rubber Bearing
Signatories:
1. Or Tan Teng 2. Shamsul Faez Mohamad Yusop
