We provide custom double glazed design solutions for any residential building or commercial project creating the ideal barrier between hot and cold temperatures.

DOUBLE GLAZING

DOUBLE GLAZINGINSULCOOL

TM

InsulCool™ provides architects and designers with the flexibility and high performance of double glazing to meet heating and cooling requirements in commercial and residential applications.

InsulCool™ Double Glazed units (also known as DGU’s or IGU’s) consist of two layers of glass separated

by an air or argon filled gap.

The combination of multiple glass panels and airspace creates an additional barrier that decreases the air-

to-air temperature transfer, while reducing direct and radiant temperature transfer from outside or inside

the building.

InsulCool units are most effective when combined with Low-E performance glass and argon gas.

Where applicable, larger spacer widths are encouraged as this increases the performance of the unit.

Comprehensive performance data on available InsulCool glass types and make-ups can be downloaded at

www.coolingbros.com.au/downloads.

Hale House Premiers Office, Installer DGA Windows Australasia

HOW TO SPECIFY InsulCool is available in various combinations of glass, thickness, colours and shapes. For a InsulCool solution tailored to suit your requirements, please call us on (08) 6104 1777, and ask to speak with a glass consultant. INSULCOOL | 30DOUBLE GLAZING

Inner glass panel

Outer glass panel

Low-e coating

Air or Argon filled space

Spacer bar

Primary sealDesiccant

Secondary seal

REDUCE SOLAR HEAT

LOW-E COATING

EXTERNAL TEMPERATURE

The primary characteristic of a low-emissivity coating is to insulate, reducing heat loss or gain. This helps maintain indoor temperature and comfort.

A Low-Emissivity coating can save a considerable amount of energy. The hard coating is applied using high temperatures (almost 600 degrees celsius) and adheres to the surface of the glass becoming remarkably durable. It can be stored, manipulated, cut and assembled like ordinary glass. It has excellent light transmission and is highly resistant to chemicals and mechanical stress. It’s real strength lies in its remarkable thermal properties as it is designed to insulate the building and can result in substantial reductions in cooling or heating costs.

To improve thermal insulation performance Low-E coated glass assembled into a double glazed unit will further improve energy loss. To increase its impact and resistance to thermal stress it can be heat strengthened or toughened. Lamination will further improve the safety and performance of the glass.

LOW-E DOUBLE GLAZING

FEATURES

Extensive range of options available using Viridian, Guardian,

AGC and St Gobain glass types

Compatible with Low E and performance glass

Excellent solar and thermal control to reduce

air-conditioning and heating costs

Air or argon filled which aids in reducing outside noise

APPLICATIONS

Residential and commercial applications where heating and

cooling is a high priority

MAXIMUM SIZE SPACER THICKNESS

2500 x 4500mm 6mm to 32mm

SPACER TYPE

Aluminium, black or silver colour options

SECONDARY SEAL

Polysulphide or Structural Silicone

GLASS TYPES

Clear Tinted Low Iron Low E Acoustic

PRIMARY SEAL

Consists of hot melt butyl or PIB. The primary seal

creates the main barrier for preventing moisture

penetration.

SPACER

Aluminium InsulCool spacers are filled with

moisture absorbing desiccant to prevent

condensation.

SECONDARY SEAL

Available in polysulphide or structural silicone, the

secondary seal is the structural component of the

unit, and holds the panes of glass together.

TYPICAL INSULCOOL CONSTRUCTION

SOFT COAT DOUBLE GLAZINGULTRACOOL-E

TM

Thermal insulation performance is becoming more of a concern when designing for differences between internal and external temperatures.

As night becomes day and the seasons change around us, the process of heat travel between glass can be

slowed down and controlled using a high performance double glazed unit (DGU).

Cooling Brothers Ultra Cool-E is a soft coat DGU and will assist in maintaining a comfortable living environment

by reducing the loss of warmth in cold temperatures and reduce heat gain in the summer months, without

compromising your view.

In addition to the standard clear glass, Ultra Cool-E is also available in green, grey, bronze and dark grey offering

lower reflectance, reduced glare and improved solar control.

HOW TO SPECIFY Ultra Cool-E is available in various combinations of glass, thickness, colours and shapes. For a Ultra Cool-E solution tailored to suit your requirements, please call us on (08) 6104 1777, and ask to speak with a glass consultant. ULTRA COOL-E | 32DOUBLE GLAZING

Si3N4

ZnOAg

SnOTiO2

Si3N4Ag

SnO2ZnO

NiCrOx

NiCrOx

Soft coat (also known as sputter coat) consists of multiple layers of metal and oxides whose combined

thickness is only 1/1000th the thickness of a human hair.

Ultra-Cool E offers the best available performance in regards to high VLT (Visible Light Transmittance) and

low SHGC (Solar Heat Gain Coefficient). With a double silver coating the result is high neutral visible light,

insulation and superior solar control. Additionally, Ultra Cool E will reduce sound transmission to further

improve building comfort.

SOFT COATED GLASS LAYERS

The performance values shown above represent NOMINAL VALUES for the centre of glass with no spacer system or framing. Slight variations may occur due to manufacturing tolerances, point of manufacture, and type of instrumentation used to measure the optical properties. For configurations which include ceramic frit coating, the actual values may vary significantly based upon the thickness and composition of the frit. For configurations with coatings laminated facing the PVB, there may be a noticeable colour change.

Cooling Brothers recommends a full size mock-up to be approved. Calculations in this report are based on NFRC 2010

Please note that the THERMAL STRESS GUIDELINE is only a rough reference to the thermal safety of a glazing. Other factors such as the size of glass areas, shapes and patterns, glass thickness, glass damaged during shipping, handling or installation, orientation of the building, exterior shading, overhangs/fins that reduce wind speed, and areas with high daily temperature fluctuations can all increase the probability of thermal breakage. The results shown are not for any specific glazing installation and do not constitute a warranty against glass breakage.

Thickness Outside Glass Inside GlassVisible Solar U Value

SHGC SC

Trans. Refl. Out Refl. In Trans. Refl. Out Air Argon

4+12+4 Ultra Cool-E #2 Clear 70 14 15 30 49 1.62 1.34 0.32 0.37

4+12+4 Grey Ultra Cool-E #3 44 8 12 20 25 1.62 1.34 0.29 0.33

4+12+4 Bronze Ultra Cool-E #3 48 9 12 21 28 1.62 1.34 0.3 0.35

6+12+6 Ultra Cool-E #2 Clear 69 14 15 29 46 1.61 1.33 0.32 0.37

6+12+6 Green Ultra Cool-E #3 58 12 13 21 12 1.61 1.33 0.31 0.36

6+12+6 Grey Ultra Cool-E #3 34 7 12 15 17 1.61 1.33 0.25 0.29

6+12+6 Bronze Ultra Cool-E #3 35 7 12 15 19 1.61 1.33 0.25 0.29

6+12+6 Dark Grey Ultra Cool-E #3 6 4 11 3 4 1.61 1.33 0.11 0.12

8+12+8 Ultra Cool-E #2 Clear 68 13 15 28 42 1.60 1.32 0.32 0.37

10+12+10 Ultra Cool-E #2 Clear 67 13 15 27 39 1.59 1.31 0.32 0.37

ULTRA COOL-E DOUBLE GLAZED OPTIONS

Whether a new build or a renovation Cooling Brothers Ultra Light-E is the perfect double glazed option for any residential purpose.

A cost effective solution for any home Ultra Light-E provides superb energy efficiency to ensure the ideal

temperature year round. Creating a barrier to ensure conditions are always perfect no matter the season

Ultra Light-E provides ideal solutions for not only insulating your home but reducing and securing it as well as.

Available in a range of different colours it is easy to find the outcome you are looking for and with the ability to

span across large gaps you can now unlock views and open spaces like never before.

Two panels of glass either toughened or annealed are separated by a spacer filled with air or argon gas to make a

Cooling Brothers Ultra Light-E unit. The panels are specifically design with high light transmission in mind which

makes them ideal for residential use. The high light transmission allows a great deal of sunlight through without

the subsequent heat.

SOFT COAT DOUBLE GLAZINGULTRALIGHT-E

R

HOW TO SPECIFY Ultra Light-E is available in various combinations of glass, thickness, colours and shapes. For a Ultra Light-E solution tailored to suit your requirements, please call us on (08) 6104 1777, and ask to speak with a glass consultant. ULTRA LIGHT-E | 34DOUBLE GLAZING

Thickness Outside Glass Inside GlassVisible Solar U Value

SHGC SC

Trans. Refl. Out Refl. In Trans. Refl. Out Air Argon

4+12+4 Ultra Light-E #2 Clear 81 13 13 54 31 1.68 1.4 0.58 0.67

4+12+4 Grey Ultra Light-E #3 51 7 11 36 17 1.68 1.4 0.43 0.49

4+12+4 Green Ultra Light-E #3 72 11 13 37 12 1.68 1.4 0.44 0.50

4+12+4 Bronze Ultra Light-E #3 55 8 11 39 19 1.68 1.4 0.45 0.52

5+12+5 Ultra Light-E #2 Clear 80 13 13 53 30 1.67 1.39 0.57 0.66

5+12+5 Grey Ultra Light-E #3 45 7 11 32 14 1.67 1.39 0.39 0.45

5+12+5 Green Ultra Light-E #3 69 11 13 34 11 1.67 1.39 0.41 0.47

5+12+5 Bronze Ultra Light-E #3 49 7 11 35 16 1.67 1.39 0.42 0.48

6+12+6 Ultra Light-E #2 Clear 79 13 13 51 29 1.66 1.39 0.57 0.65

6+12+6 Grey Ultra Light-E #3 39 6 11 28 12 1.66 1.39 0.36 0.41

6+12+6 Green Ultra Light-E #3 67 10 12 31 9 1.66 1.39 0.39 0.44

6+12+6 Bronze Ultra Cool-E #3 44 7 11 31 14 1.66 1.38 0.39 0.44

The performance values shown above represent NOMINAL VALUES for the centre of glass with no spacer system or framing. Slight variations may occur due to manufacturing tolerances, point of manufacture, and type of instrumentation used to measure the optical properties. For configurations which include ceramic frit coating, the actual values may vary significantly based upon the thickness and composition of the frit. For configurations with coatings laminated facing the PVB, there may be a noticeable colour change.

Cooling Brothers recommends a full size mock-up to be approved. Calculations in this report are based on NFRC 2010

Please note that the THERMAL STRESS GUIDELINE is only a rough reference to the thermal safety of a glazing. Other factors such as the size of glass areas, shapes and patterns, glass thickness, glass damaged during shipping, handling or installation, orientation of the building, exterior shading, overhangs/fins that reduce wind speed, and areas with high daily temperature fluctuations can all increase the probability of thermal breakage. The results shown are not for any specific glazing installation and do not constitute a warranty against glass breakage.

ULTRA LIGHT-E DOUBLE GLAZED OPTIONS

FEATURES

Excellent solar and thermal control to reduce

air-conditioning and heating costs

Combine with tinted interlayers

Air or argon filled which aids in reducing outside noise

APPLICATIONS

Residential and commercial applications where heating

and cooling is a high priority

MAXIMUM SIZE SPACER THICKNESS

2500mm x 4500mm 6mm to 32mm

GLASS TYPES

Clear Tinted Low Iron Low E

Melbourne

4 Dream Haven Court, Epping, Victoria 3076

(03) 9408 3466

Brisbane

1300 040 799 . 0404 610 081

Perth

961 Abernethy Rd, High Wycombe, WA, 6057

(08) 6104 1777

Sydney

U8, 7-9 Jullian Cl, Banksmeadow, NSW, 2019

1300 040 799 . 0404 610 081 info@coolingbros.com.au . coolingbros.com.au