Upload
juliet-standard
View
263
Download
5
Embed Size (px)
Citation preview
DRILLINGENGINEERING
Vahid Salimi
Textbook
Applied Drilling Engineering,
by :Adam T. Bourgoyne Jr.,
Martin E. Chenevert,
Keith K. Millheim
F.S. Young Jr.,.
pore pressure and fracture pressuredrilling hydraulicscasing designunder balanced drillingdirectional drilling
Contents:
Chapter 1
pore pressure and fracture pressure
Hydrostatic Pressure
• Hydrostatic pressure is defined as the pressure exerted by a column of fluid.
• The pressure is a function of the average fluid density and the vertical height or depth of the fluid column.
• Mathematically, hydrostatic pressure is expressed as:
HP (psi) = 0.052 x ρf (ppg) x D (ft) where: HP = hydrostatic pressure ρf = average fluid density D = true vertical depth or height of the column
Hydrostatic Pressure(cont’d)
Hydrostatic pressures can easily be converted to equivalent mud weights and pressure gradients.
Hydrostatic pressure gradient is given by: HG = HP / D … (psi/ft)
ExampleCalculate the hydrostatic pressure for the
following wells:• a. mud weight = 9 ppg, hole depth = 10100 ft MD (measured
depth), 9900 ft TVD (true vertical depth)• b. mud gradient = 0.468 psi / ft, hole depth = 10100 ft MD
(measured depth), 9900 ft TVD (true vertical depth)
solutiona.
HP (psi) = 0.052 x ρf (ppg) x D (ft) = 0.052 x 9 x 9900 = 4632 psi
b. Hydrostatic pressure = fluid gradient (psi / ft) x depth (ft)..........psi
= 0.468 (psi /ft) x 9900(ft) = 4633 psi
Mud Weight (MW) should be kept heavy enough so that hydrostatic head of mud column is higher than formation pressure at any depth. Usually 150 psi
Need to know formation pressure in order to determine MW
Pf + 150 = 0.052 MW DPf Formation Pressure, psiMW Mud Weight, ppgD True Vertical Depth, ft150 Safety, psi
Example
You are drilling with 7.9 ppg oil base mud. If the formation pressure is predicted 5,000 psi at 9,000 ft true vertical depth, what is the required MW in order to have 150 psi overpressure ?
5,000 + 150 = 0.052 MW 9,000
MW = 11 ppg
OVERBURDEN PRESSURE
The overburden pressure is defined as the pressure exerted by the total weight of overlyingformations above the point of interest.
The total weight is the combined weight of both the formation solids (rock matrix) and formation fluids in the pore space.
The overburden pressure can therefore be expressed as the hydrostatic pressure exerted by all materials overlying the depth of interest:
σov = 0.052 x ρb x Dwhere σov = overburden pressure (psi) ρb = formation bulk density (ppg) D = true vertical depth (ft)
OVERBURDEN PRESSURE(cont’d)
Overburden gradient under field conditions of varying lithological and pore fluid density is given by:
σovg= 0.433[(1 – φ)ρma +(φxρf)]where
σovg= overburden gradient, psi/ft φ= porosity expressed as a fraction ρf= formation fluid density ρma= matrix density
matrix and fluid densities
Substance Density (gm/cc)Sandstone 2.65Limestone 2.71Dolomite 2.87Anhydrite 2.98Halite 2.03Gypsum 2.35Clay 2.7 - 2.8Freshwater 1.0Seawater 1.03 - 1.06Oil 0.6 - 0.7Gas 0.15
To convert densities from gm/cc to gradients in psi/ft use:Gradient (psi/ft) = 0.433 x (gm /cc)
To convert from psi/ft to ppg, use:Density (ppg) = gradient (psi/ft) / 0.052
Pore pressure The magnitude of pressure in the pore of formation known as the pore pressure
Pore pressure= formation pressure=formation fluid pressure=reservoir pressure
=pressure in fluid contained in the pore spaces of the rock
Example Determine the pore pressure of a
normally pressured formation in the Gulf of Mexico at 9,000’ depth.
Solution p = 0.465 psi/ft * 9,000 ft = 4,185 psig
Homework: Pore Pressure Profiles The following pore pressure information has been supplied
for the well you are about to drill.
a. Plot the following pore pressure/depth information on a P-Z diagram :
b. Calculate the pore pressure gradients in the formations from surface; to 8000ft; to 8500ft; and to 9500ft. Plot the overburden gradient (1 psi/ft) on the above plot.
Determine the mud weight required to drill the hole section: down to 8000ft; down to 8500ft; and down to 9500ft.
Assume that 200 psi overbalance on the formation pore pressure is required.
c. If the mudweight used to drill down to 8000ft were used to drill into the formation pressures at 8500ft what would be the over/underbalance on the formation pore pressure at this depth?
d. Assuming that the correct mudweight is used for drilling at 8500ft but that the fluid level in the annulus dropped to 500 ft below drillfloor, due to inadequate hole fill up during tripping. What would be the effect on bottom hole pressure at 8500ft ?
e. What type of fluid is contained in the formations below 8500ft.
Normal Pore Pressure Pressure of a column of water extending from the formation to the surface The magnitude of normal pore pressure varies with the concentration of
dissolved salts, type of fluid, gases present and temperature gradient.
=0.433 psi/ft for fresh water=0.465 psi/ft for seawater
Subnormal Formation Pressure Subnormal pore pressure is defined as any formation pressure that is
less than the corresponding fluid hydrostatic pressure at a given depth. Subnormal formation pressure can cause lost circulation of water as the
drilling fluid.
ABNORMAL PORE PRESSURE
Abnormal pore pressure is defined as any pore pressure that is greater than the hydrostatic pressure of the formation water occupying the pore space. Abnormal pressure is sometimes called overpressure or geopressure. Abnormal pressure can be thought of as being made up of a normal hydrostatic component plus an extra amount of pressure. This excess pressure is the reason why surface control equipment (e.g. BOPs) are required when drilling oil and gas wells.
ABNORMAL PORE PRESSURE(cont’d)
Abnormal formation pressure can cause a kick with water as the drilling fluid.
Abnormal Pressure Gradients
Normal Pressure Gradients West Texas: 0.433 psi/ft Gulf Coast: 0.465 psi/ft
Normal and Abnormal Pore Pressure
Pore Pressure, psig
Dep
th,
ft
10,000’
Pore Pressure vs. Depth
8 9 10 11 12 13 14 15 16Pore Pressure Equivalent, lb/gal
0
5,000
10,000
15,000
20,000
{ Density of mud required to control this pore pressure }
Dep
th,
ft
Normal
Abormal
0.433 psi/ft 8.33 lb/gal0.465 psi/ft 9.0 lb/gal
Pore Pressure Gradient
Fracture Gradient
Transition zoneThe upper portion of the region of abnormal pressure is called the transition zone
Causes Of Abnormal Pore Pressure
Compaction EffectsDiagenetic EffectsDifferentional Density EffectsFluid Migration Effects
Diagenetic Effects
With increasing pressure and temperature, sediments undergo a process of chemical and physical changes collectively known as diagenesis.
Diagenesis is the alteration of sediments and their constituent minerals during post depositional compaction.
Diagenetic processes include the formation of new minerals, recrystallisation and lithification.
Diagenesis may result in volume changes and water generation which if occurring in a seabed environment may lead to both abnormal or sub-normal pore pressure.
Clay Diagenesis
Clay Diagenesis (Conversion of Smectite to Illite) If the water released in this process cannot escape during compaction, then the
pore fluid will support an increased portion of the overburden and will thus be abnormally pressured.
Diagenesis of Sulphate Formations Anhydrite (CaSO4) is diagenetically formed from the dehydration of gypsum
(CaSO4.2H2O). During the process large volumes of water are released and this is accompanied by
a 30-40% reduction in formation volume
7. Abnormal Pressure 661. Drilling Engineering Slide 33
HIGH PRESSURE
NORMAL PRESSURE
Homework
661. Drilling Engineering7. Abnormal Pressure Slide 37
When crossing faults it is possible to go from normal pressure to abnormally high pressure in a short interval.
7. Abnormal Pressure 661. Drilling Engineering Slide 38Well “A” found only Normal Pressure ...
Methods of estimating pore pressureDirect measurementIt is possible only when the formation has been drilledIt is expensiveIndirect measurementThe main parameter is the variation of porosity with depth (porosity dependent parameter)If pore pressure is normal, porosity-dependent parameter (x) have an easily recognized trend because of the decreased porosity with increased depth of burial and compaction.A departure from the normal pressure trend signals a probable transition zone.Detection of the depth at which this departure occurs is critical because casing must be set in the well before excessively pressured permeable zones can be drilled safely.
7. Abnormal Pressure 661. Drilling Engineering Slide 40
Prediction and Detection of Abnormal Pressure Zones
1. Before drilling
4 Shallow seismic surveys
4 Deep seismic surveys
4 Comparison with nearby wells
7. Abnormal Pressure 661. Drilling Engineering Slide 41
Prediction and Detection of Abnormal Pressure Zones
2. While drilling
4 Drilling rate, gas in mud, etc. etc.
4 D - Exponent
4 DC - Exponent
4 MWD - LWD
4 Density of shale (cuttings)
7. Abnormal Pressure 661. Drilling Engineering Slide 42
Prediction and Detection of Abnormal Pressure Zones
3. After drilling
4 Resistivity log
4 Conductivity log
4 Sonic log
4 Density log
Compaction Theory of Abnormal Pressure
During deposition, sediments are compacted by the overburden load and are subjected to greater temperatures with increasing burial depth.Porosity is reduced as water is forced out.Hydrostatic equilibrium within the compacted layers is retained as long as the expelled water is free to escape If water cannot escape, abnormal pressures occur
Compaction Theory In Porous formation the overburden stress is supported by rock matrix
stress and pore pressure Bulk Density = ρm (1-Ф) + ρf Ф The average porosity in sediments ,generally decreases with increasing
depth - due to the increasing overburden This results in an increasing bulk density with increasing depth, and
increasing rock strength Average Porosity Ф = ρm - ρb / ρm – ρf Plot Ф Vs. Depth on similog graph.
Example
Calculate the overburden stress at a depth of 7,200 ft in the Santa Barbara Channel.
Assumeφo = 0.37ρma = 2.6 gm/cckφ = 0.0001609 ft-1ρf = 1.044 gm/cc
Solution
Homeworks
Homeworks (cont’d)
Homeworks (cont’d)
Pore pressure prediction methods
Measure the porosity indicator (e.g.density) in normally pressured, clean shales to establish a normal trend line.
When the indicator suggests porosity values that are higher than the trend, then abnormal pressures are suspected to be present.
The magnitude of the deviation from the normal trend line is used to quantify the abnormal pressure.
Equivalent Matrix Stress Method
Example Estimate the pore pressure at 10,200’ if the equivalent depth
is 9,100’. The normal pore pressure gradient is 0.433 psi/ft. The overburden gradient is 1.0 psi/ft.
ASSUME: At 9,100’, pne = 0.433 * 9,100 = 3,940 psig At 9,100’, σobe = 1.00 * 9,100 = 9,100 psig At 10,200’, σob = 1.00*10,200 = 10,200 psig
Solution
Approach 2: Empirical correlation More accurate Need numerous data Uses (Xo-Xn) or (Xo/Xn) to predict the
magnitude of the abnormal pressure
Prediction of pore pressure by seismic data
Homework
Pore pressure indications while drilling
Drilling rate (ROP) gas in mudPit levelFlowline temperature
Rate Of Penetration(ROP) Drill bits break the rock by a combination of several processes
including: Compression (weight-on-bit), shearing (rpm) and sometimes jetting action of the drilling fluid.
The speed of drilling is described as the rate of penetration (ROP) and is measured in ft/hr.
The rate of penetration is affected by numerous parameters namely:
Weight On Bit (WOB) Revolutions Per Minute (RPM) bit type bit wear hydraulic efficiency degree of overbalance drilling fluid properties hydrostatic pressure and hole size Formation properties
75
Note, that many factors can influence the drilling rate, and some of these factors are outside the control of the operator.
TABLE 2.8 -
76
Effect of bit weight and hydraulics on penetration rate
Inadequate hydraulics or excessive imbedding of the bit teeth in the rock
Drilling rate increases more or less linearly with increasing bit weight.
A significant deviation from this trend may be caused by poor bottom hole cleaning
0
77
Effect of Differential Pressure on Drilling Rate
Differential pressure is the difference between wellbore pressure and pore fluid pressure
Decrease can be due to:
• The chip hold down effect
• The effect of wellbore pressure on rock strength
If all parameters affecting ROP are held constant whilst drilling a uniform shale sequence then ROP should decrease with depth. This is due to the natural increased compaction with depth reflecting a decrease in porosity and increased shale density and increased shale (compressive) strength.
When entering an abnormally pressured shale, the drill bit sees a shale section which is undercompacted. The increased porosity and decreased density of the undercompacted section results in the formation becoming more ‘drillable’ as there is less rock matrix to remove. Consequently ROP increases, assuming all drilling parameters were kept constant.
79
Drilling underbalanced can further increase the drilling rate.
Drilling Rate as a Pore Pressure PredictorPenetration rate depends on a number of different parameters.
R = K(P1)a1 (P2)a2 (P3)a3… (Pn)an
81
Modified d-exponent
82
The D Exponent basically attempts to correct the ROP for changes in RPM, weight on bit and hole size.
The D exponent increases linearly with depth, reflecting increased rock strength with depth. For abnormally pressured shales, the D exponent deviates from the normal trend and actually decreases with depth.
Or, in its most used form:
in Diameter,Bit d
lbf ,Bit WeightW
exponentdd
rpmN
ft/hrR
10
12log
60log
b
6
bd
WN
R
d
83
dc-exponentMud weight also affects R
An adjustment to d may be made:
dc = d (rn /rc)
wheredc = exponent corrected for mud density
rn = normal pore pressure gradient
rc = effective mud density in use
84
d-exponent The d-exponent normalizes R for any
variations in W, db and N
Under normal compaction, R should decrease with depth. This would cause d to increase with depth.
Any deviation from the trend could be caused by abnormal pressure.
85
Example• While drilling in a Gulf Coast shale,
R = 50 ft/hr
W = 20,000 lbf
N = 100 RPM
ECD = 10.1 ppg (Equivalent Circulating Density)
db = 8.5 in
• Calculate d and dc
86
Solution
34.1d
554.1
079.2
5.8*10000,20*12
log
100*6050
logd
6
bdWN
R
d
61012
log
60log
c
nc dd
19.1d
1.10*052.0
465.034.1d
c
c
Example
solution
Ratio Method
The ratio method is much simpler and does not require values of overburden. To calculatepore pressure, use the following formula:
Homework • Using the Eaton Method, calculate the pore
pressure at depth 12000 ft given:
dcn (from normal trend) = 1.5 d-unitsdco (from new trend) = 1.1 d-unitsOverburden gradient = 19 ppgNormal pore pressure in area = 9 ppg
Fracture Pressure
Fracture Gradients 1.11- 101
Prediction of Fracture Gradients
4Well Planning4Theoretical Fracture Gradient Determination
4Hubbert & Willis4Matthews & Kelly4Ben Eaton4Comparison of Results
4Experimental Frac. Grad. Determination4Leak-off Tests
In-Situ Earth Stresses
Example
Fracture Gradients 1.11- 106
Fracture Gradient Determination
2. Matthews & Kelly:
where Ki = matrix stress coefficient
s = vertical matrix stress, psi
D
P
D
KF i
Fracture Gradients 1.11- 107
Example
A Texas Gulf Coast well has a pore pressure gradient of 0.735 psi/ft. Well depth = 11,000 ft.
Calculate the fracture gradient in units of lb/gal using Matthews & Kelly method
Summarize the results in tabular form, showing answers, in units of lb/gal and also in psi/ft.
Fracture Gradients 1.11- 108
2. Matthews & Kelly
In this case P and D are known, may be calculated, and is determined graphically.
(i) First, determine the pore pressure gradient.
D
K
D
PF i
iK
Example
)given(ft/psi735.0D
P
Fracture Gradients 1.11- 109
Example - Matthews and Kelly
(ii) Next, calculate the matrix stress.
ft ,depthD
psi ,pressure poreP
psi ,stress matrix
psi ,overburdenS
S = P + s
s = S - P = 1.00 * D - 0.735 * D = 0.265 * D = 0.265 * 11,000s = 2,915 psi
Example - Matthews and Kelly
(iii) Now determine the depth, , where, under normally pressured conditions, the rock matrix stress, s would be 2,915 psi.
iD
Sn = Pn + sn n = “normal”
1.00 * Di = 0.465 * Di + 2,915
Di * (1 - 0.465) = 2,915
ft449,5535.0
915,2Di
Fracture Gradients 1.11- 111
Example - Matthews and
Kelly
(iv) Find Ki from the plot on the right, for
For a south Texas Gulf Coast well,
Di = 5,449 ft
Ki = 0.685
Example - Matthews and Kelly
(v) Now calculate F:D
P
D
KF i
735.0000,11
915,2*685.0F
ft/psi9165.0
gal/lb63.17052.0
9165.0F
Leak off Test A test carried out to the point where the formation leaks off
Fracture Gradients 1.11- 114
Slide 115
Experimental Determination of Fracture Gradient
Example:In a leak-off test below the casing seat at 4,000 ft, leak-off was found to occur when the standpipe pressure was 1,000 psi.
MW = 9 lb/gal.
What is the fracture gradient?
Slide 116
Solution
Leak-off pressure = PS + DPHYD
= 1,000 + 0.052 * 9 * 4,000= 2,872 psi
Fracture gradient = 0.718 psi/ft
EMW = ?
ft
psi
000,4
872,2
D
P OFFLEAK
13.8 lb/gal
Homework While performing a leak off test the surface pressure at leak
off was 940 psi. The casing shoe was at a true vertical depth of 5010 ft and a mud weight of 10.2 ppg was used to conduct the test.
Calculate: the maximum allowable mud weight at this depth .
Homework A leakoff test was carried out just below a 13 3/8" casing shoe at 7000 ft.
TVD using 9.0 ppg mud. The results of the tests are shown below. What is the maximum allowable mud weight for the 12 1/4" hole section ?
BBLS PUMPED SURFACE PRESSURE
1 4001.5 6702 8802.5 11003 13503.5 16004 18004.5 19005 1920
(psi)
Equivalent Circulating Density (ECD) When the drilling fluid is circulating through the drillstring, the
borehole pressure at the bottom of the annulus will be greater than the hydrostatic pressure of the mud.
The extra pressure is due to the frictional pressure required to pump the fluid up the annulus. This frictional pressure must be added to the pressure due to the hydrostatic pressure from the column of mud to get a true representation of the pressure acting against the formation a the bottom of the well.
An equivalent circulating density (ECD) can then be calculated from the sum of the hydrostatic and frictional pressure divided by the true vertical depth of the well.
Homework
If the circulating pressure losses in the annulus of the above well is 300 psi when drilling at 7500ft with 9.5ppg mud, what would be the ECD of the mud at 7500ft.