DRPC-120-BTi Embedded System - ICP America · DRPC-120-BTi Embedded System Page i User Manual MODEL: DRPC-120-BTi Fanless Embedded System with Intel® Atom™ E3845 CPU, ... 36 4

DRPC-120-BTi Embedded System

Page i

User Manual

MODEL:

DRPC-120-BTi Fanless Embedded System with Intel Atom E3845 CPU,

DIN Rail Mounting Support, OLED Display or LED Indicators, Dual GbE, USB, DIO, Serial Ports,

9V~28V DC Power Input, RoHS Compliant

Rev. 1.00 November 20, 2014


Page ii

Revision Date Version Changes

November 20, 2014 1.00 Initial release


Page iii

Copyright COPYRIGHT NOTICE

The information in this document is subject to change without prior notice in order to

improve reliability, design and function and does not represent a commitment on the part

of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or

consequential damages arising out of the use or inability to use the product or

documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are

reserved. No part of this manual may be reproduced by any mechanical, electronic, or

other means in any form without prior written permission of the manufacturer.

TRADEMARKS

All registered trademarks and product names mentioned herein are used for identification

purposes only and may be trademarks and/or registered trademarks of their respective

owners.


Page iv

Table of Contents 1 INTRODUCTION.......................................................................................................... 1

1.1 OVERVIEW.................................................................................................................. 2 1.2 MODEL VARIATIONS ................................................................................................... 2 1.3 FEATURES................................................................................................................... 3 1.4 CONNECTOR PANEL.................................................................................................... 4

1.4.1 Front Panel ........................................................................................................ 4 1.4.2 Top Panel ........................................................................................................... 5

1.5 LED INDICATORS (DRPC-120-BTI-E5-LED ONLY).................................................. 6 1.6 PROGRAMMABLE OLED DISPLAY (DRPC-120-BTI-E5-OLED ONLY) ..................... 7 1.7 TECHNICAL SPECIFICATIONS ...................................................................................... 7 1.8 DIMENSIONS............................................................................................................. 10

2 UNPACKING ................................................................................................................11

2.1 ANTI-STATIC PRECAUTIONS...................................................................................... 12 2.2 UNPACKING PRECAUTIONS....................................................................................... 12 2.3 UNPACKING CHECKLIST ........................................................................................... 13

3 INSTALLATION ......................................................................................................... 16

3.1 INSTALLATION PRECAUTIONS ................................................................................... 17 3.1.1 High Surface Temperature ............................................................................... 17

3.2 INTERNAL ACCESS PANEL REMOVAL ........................................................................ 18 3.3 HDD INSTALLATION................................................................................................. 18 3.4 MSATA SSD INSTALLATION..................................................................................... 19 3.5 IPMI MODULE INSTALLATION (OPTIONAL).............................................................. 21 3.6 CLEAR CMOS.......................................................................................................... 23 3.7 AT/ATX MODE SELECTION...................................................................................... 24 3.8 MOUNTING THE SYSTEM .......................................................................................... 24 3.9 EXTERNAL PERIPHERAL INTERFACE CONNECTORS................................................... 26

3.9.1 Digital Input/Output Terminal Block ............................................................... 27 3.9.2 LAN Connectors............................................................................................... 27 3.9.3 Power Input, 3-pin Terminal Block.................................................................. 29


Page v

3.9.4 RS-232 Serial Port Connectors (COM1, COM2) ............................................ 30 3.9.5 RS-422/485 Serial Port Connectors (COM3, COM4) ..................................... 31 3.9.6 USB Connectors............................................................................................... 32 3.9.7 VGA Connector ................................................................................................ 33

3.10 IPMI SETUP PROCEDURE ....................................................................................... 33 3.10.1 Managed System Hardware Setup ................................................................. 34 3.10.2 Using the IEI iMAN Web GUI........................................................................ 34

3.11 DRIVER INSTALLATION ........................................................................................... 36

4 SYSTEM MAINTENANCE ....................................................................................... 37

4.1 SYSTEM MAINTENANCE INTRODUCTION .................................................................. 38 4.2 MOTHERBOARD REPLACEMENT ............................................................................... 38 4.3 SO-DIMM REPLACEMENT....................................................................................... 39

5 BIOS.............................................................................................................................. 41

5.1 INTRODUCTION......................................................................................................... 42 5.1.1 Starting Setup................................................................................................... 42 5.1.2 Using Setup ...................................................................................................... 42 5.1.3 Getting Help..................................................................................................... 43 5.1.4 Unable to Reboot after Configuration Changes .............................................. 43 5.1.5 BIOS Menu Bar................................................................................................ 43

5.2 MAIN........................................................................................................................ 44 5.3 ADVANCED ............................................................................................................... 46

5.3.1 ACPI Settings ................................................................................................... 47 5.3.2 Super IO Configuration ................................................................................... 48

5.3.2.1 Serial Port n Configuration ....................................................................... 49 5.3.3 iWDD H/W Monitor ......................................................................................... 54

5.3.3.1 Smart Fan Mode Configuration ................................................................ 55 5.3.4 RTC Wake Settings ........................................................................................... 57 5.3.5 Serial Port Console Redirection ...................................................................... 58 5.3.6 CPU Configuration .......................................................................................... 60 5.3.7 IDE Configuration ........................................................................................... 63 5.3.8 USB Configuration........................................................................................... 64

5.4 CHIPSET ................................................................................................................... 65 5.4.1 North Bridge .................................................................................................... 66


Page vi

5.4.2 South Bridge..................................................................................................... 66 5.4.2.1 PCI Express Configuration ....................................................................... 68

5.5 SECURITY................................................................................................................. 69 5.6 BOOT........................................................................................................................ 70 5.7 EXIT ......................................................................................................................... 72

6 PROGRAMMING OLED FOR DRPC-120-BTI-E5-OLED ................................... 74

6.1 OVERVIEW................................................................................................................ 75 6.2 OLED IMAGE EDITOR.............................................................................................. 75

6.2.1 OLED Image Editor Installation ..................................................................... 75 6.2.2 Launching the OLED Image Editor................................................................. 78 6.2.3 Function List .................................................................................................... 78 6.2.4 OLED Control.................................................................................................. 79 6.2.5 OLED Erase Page............................................................................................ 80

6.3 DRPC100 DEMO PROGRAM..................................................................................... 81 6.3.1 Dialog Menu .................................................................................................... 82 6.3.2 LCD Menu........................................................................................................ 83 6.3.3 DEMO Menu.................................................................................................... 84

7 INTERFACE CONNECTORS ................................................................................... 85

7.1 PERIPHERAL INTERFACE CONNECTORS..................................................................... 86 7.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 87

7.2.1 Audio Line-out Connector (LINE_OUT1) ....................................................... 88 7.2.2 Audio Mic-in Connector (MIC_IN1)................................................................ 88 7.2.3 Battery Connector (BAT1) ............................................................................... 88 7.2.4 Chassis Intrusion Connector (CHASSIE1) ...................................................... 88 7.2.5 CPU Fan Connector (CPU_FAN1).................................................................. 89 7.2.6 OLED/LED Signal Connector (OLED1) ......................................................... 89 7.2.7 PCIe Mini Card Slot Full Size (M_PCIE1) .................................................. 89 7.2.8 PCIe Mini Card Slot Half Size (MINI-PCIE1) ............................................. 90 7.2.9 SATA 3Gb/s Connector (SATA1) ...................................................................... 91 7.2.10 SATA Power Connector (SATA_PWR1) ......................................................... 92 7.2.11 SPI Flash Connector (JSPI1)......................................................................... 92 7.2.12 SPI Flash Connector - EC (JSPI2) ................................................................ 92 7.2.13 USB Connector (USB1) ................................................................................. 93


Page vii

7.3 EXTERNAL INTERFACE PANEL CONNECTORS ............................................................ 93 7.3.1 Digital I/O Terminal Block (J1) ....................................................................... 94 7.3.2 Power Input Terminal Block (DC_IN1) ........................................................... 94 7.3.3 RJ-45 LAN Connector (LAN1)......................................................................... 94 7.3.4 RJ-45 LAN Connector (LAN2)......................................................................... 95 7.3.5 RS-232 Serial Ports (COM1/2)........................................................................ 95 7.3.6 RS-422/485 Serial Ports (COM3/4)................................................................. 95 7.3.7 USB 2.0 Connectors (USB2)............................................................................ 96 7.3.8 USB 3.0 Connectors (USB1)............................................................................ 96 7.3.9 VGA Connector (VGA1)................................................................................... 96

A SAFETY PRECAUTIONS ......................................................................................... 98

A.1 SAFETY PRECAUTIONS ............................................................................................ 99 A.1.1 General Safety Precautions ............................................................................. 99 A.1.2 Anti-static Precautions .................................................................................. 100 A.1.3 Explanation of Graphical Symbols................................................................ 100 A.1.4 Product Disposal ........................................................................................... 101

A.2 MAINTENANCE AND CLEANING PRECAUTIONS...................................................... 101 A.2.1 Maintenance and Cleaning............................................................................ 101 A.2.2 Cleaning Tools ............................................................................................... 102

B DIGITAL I/O INTERFACE ..................................................................................... 103

B.1 INTRODUCTION...................................................................................................... 104 B.2 ASSEMBLY LANGUAGE SAMPLE 1.......................................................................... 105 B.3 ASSEMBLY LANGUAGE SAMPLE 2.......................................................................... 105

C HAZARDOUS MATERIALS DISCLOSURE ....................................................... 106

C.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ..................................... 107


Page viii

List of Figures Figure 1-1: DRPC-120-BTi Series ..................................................................................................2 Figure 1-2: DRPC-120-BTi-E5-LED Front Panel...........................................................................4 Figure 1-3: DRPC-120-BTi-E5-OLED Front Panel ........................................................................5 Figure 1-4: DRPC-120-BTi Top Panel............................................................................................6 Figure 1-5: LED Indicators of DRPC-120-BTi-E5-LED.................................................................6 Figure 1-6: Physical Dimensions (millimeters)..........................................................................10 Figure 3-1: Internal Access Panel Removal...............................................................................18 Figure 3-2: HDD Installation ........................................................................................................19 Figure 3-3: PCIe Mini Slot Location ............................................................................................20 Figure 3-4: Inserting the PCIe Mini Card into the Socket .........................................................20 Figure 3-5: Securing the PCIe Mini Card....................................................................................21 Figure 3-6: IPMI Module Slot Location .......................................................................................22 Figure 3-7: IPMI Module Installation ...........................................................................................22 Figure 3-8: Clear CMOS Button Location...................................................................................23 Figure 3-9: AT/ATX Switch Location...........................................................................................24 Figure 3-10: DIN Rail Mounting Bracket Installation.................................................................24 Figure 3-11: Attach the Mounting Bracket to the DIN Rail .......................................................25 Figure 3-12: Mounting the System..............................................................................................26 Figure 3-13: DIO Terminal Block Pinout Location.....................................................................27 Figure 3-14: RJ-45 Ethernet Connector......................................................................................28 Figure 3-15: 3-pin Power Terminal Block Pinout Location.......................................................29 Figure 3-16: RS-232 Serial Port Pinout Location.......................................................................30 Figure 3-17: RS-422/485 Serial Port Pinout Locations..............................................................31 Figure 3-18: VGA Connector .......................................................................................................33 Figure 3-19: IEI iMAN Web Address............................................................................................34 Figure 3-20: IEI iMAN Web GUI....................................................................................................35 Figure 4-1: SO-DIMM Module Location.......................................................................................39 Figure 4-2: SO-DIMM Module Installation...................................................................................40 Figure 6-1: OLED Image Editor Setup Wizard ...........................................................................76 Figure 6-2: Select Installation Folder..........................................................................................76


Page ix

Figure 6-3: Confirm Installation ..................................................................................................77 Figure 6-4: Installation Complete................................................................................................77 Figure 6-5: OLED Image Editor ...................................................................................................78 Figure 6-6: Function List..............................................................................................................78 Figure 6-7: OLED Control ............................................................................................................79 Figure 6-8: OLED Erase Page......................................................................................................80 Figure 6-9: DR100 Demo Program Main Menu ..........................................................................81 Figure 6-10: Dialog Menu.............................................................................................................82 Figure 6-11: LCD Menu ................................................................................................................83 Figure 6-12: DEMO Menu .............................................................................................................84 Figure 7-1: Main Board Layout Diagram (Front Side) ...............................................................86 Figure 7-2: Main Board Layout Diagram (Solder Side) .............................................................86


Page x

List of Tables Table 1-1: DRPC-120-BTi Model Variations .................................................................................2 Table 1-2: DRPC-120-BTi-E5-LED LED Definitions .....................................................................7 Table 1-3: Technical Specifications..............................................................................................9 Table 3-1: DIO Terminal Block Pinouts ......................................................................................27 Table 3-2: LAN1 Pinouts ..............................................................................................................28 Table 3-3: LAN2 Pinouts ..............................................................................................................28 Table 3-4: RJ-45 Ethernet Connector LEDs ...............................................................................28 Table 3-5: 3-pin Power Terminal Block Pinouts ........................................................................29 Table 3-6: RS-232 Serial Port Pinouts ........................................................................................30 Table 3-7: RS-422/485 Serial Port Pinouts .................................................................................31 Table 3-8: USB 2.0 Port (USB3/USB4) Pinouts ..........................................................................32 Table 3-9: USB 3.0 Port (USB1/USB2) Pinouts ..........................................................................32 Table 3-10: VGA Connector Pinouts...........................................................................................33 Table 5-1: BIOS Navigation Keys ................................................................................................43 Table 7-1: Peripheral Interface Connectors ...............................................................................87 Table 7-2: Audio Line-out Connector (LINE_OUT1) Pinouts....................................................88 Table 7-3: Audio Mic-in Connector (MIC_IN1) Pinouts .............................................................88 Table 7-4: Battery Connector (BAT1) Pinouts ...........................................................................88 Table 7-5: Chassis Intrusion Connector (CHASSIE1) Pinouts.................................................88 Table 7-6: CPU Fan Connector (CPU_FAN1) Pinouts ...............................................................89 Table 7-7: OLED/LED Signal Connector (OLED1) Pinouts.......................................................89 Table 7-8: PCIe Mini Card Slot Full Size (M_PCIE1) Pinouts.................................................90 Table 7-9: PCIe Mini Card Slot Half Size (MINI-PCIE1) Pinouts ............................................91 Table 7-10: SATA 3Gb/s Connector (SATA1) Pinouts ..............................................................91 Table 7-11: SATA Power Connector (SATA_PWR1) Pinouts ...................................................92 Table 7-12: SPI Flash Connector (JSPI1) Pinouts .....................................................................92 Table 7-13: SPI Flash Connector - EC (JSPI2) Pinouts.............................................................92 Table 7-14: USB Connector (USB1) Pinouts..............................................................................93 Table 7-15: Rear Panel Connectors ............................................................................................93 Table 7-16: Digital I/O Terminal Block (J1) Pinouts ..................................................................94


Page xi

Table 7-17: Power Input Terminal Block (DC_IN1) Pinouts......................................................94 Table 7-18: RJ-45 LAN Connector (LAN1) Pinouts ...................................................................94 Table 7-19: RJ-45 LAN Connector (LAN2) Pinouts ...................................................................95 Table 7-20: RS-232 Serial Port (COM1/2) Pinouts .....................................................................95 Table 7-21: RS-422/485 Serial Port (COM3/4) Pinouts ..............................................................95 Table 7-22: USB 2.0 Connectors (USB2) Pinouts......................................................................96 Table 7-23: USB 3.0 Connectors (USB1) Pinouts......................................................................96 Table 7-24: VGA Connector (VGA1) Pinouts .............................................................................97

DRPC-120-BTi


Page 1

Chapter

1

1 Introduction


Page 2

1.1 Overview

Figure 1-1: DRPC-120-BTi Series

The DRPC-120-BTi fanless embedded system is powered by the Intel Atom E3845

processor. It is designed for harsh environment applications, and supports DIN rail

mounting method.

The DRPC-120-BTi accepts a wide range of DC power input (9 V ~ 28 V), allowing it to be

powered anywhere. Two USB 3.0, two USB 2.0, two GbE, two RS-232, two RS-422/485,

and one 8-bit DIO provide rich I/O options for various applications.

1.2 Model Variations

The model variations of the DRPC-120-BTi are listed below.

Model No. Indicators

DRPC-120-BTi-E5-LED/2G LED

DRPC-120-BTi-E5-OLED/2G OLED

Table 1-1: DRPC-120-BTi Model Variations


Page 3

1.3 Features

The DRPC-120-BTi features are listed below:

1.91 GHz quad-core Intel Atom E3845 processor

Low power consumption

Fanless design

DIN rail mounting support

Preinstalled one 2 GB DDR3L SO-DIMM (system max. 8 GB)

Supports one mSATA and one 2.5 SATA HDD

Wide range DC power input (9 V ~ 28 V)

Extended temperature fanless design supports -20C ~ 60C (with SSD)

Two PCIe Mini card slots

Serial interfaces with isolation protection

8-bit digital IO (4-bit output, 4-bit input)

Supports two GbE, two USB 3.0, two USB 2.0, two RS-232 and two

RS-422/485

LED indicators (DRPC-120-BTi-E5-LED only)

Programmable OLED display (DRPC-120-BTi-E5-OLED only)

RoHS compliant


Page 4

1.4 Connector Panel

1.4.1 Front Panel

The DRPC-120-BTi front panel contains:

2 x RJ-45 Gigabit LAN ports

2 x RS-232 serial ports with isolation

2 x RS-422/485 serial ports with isolation

2 x USB 3.0 ports

2 x USB 2.0 ports

LED or OLED indicators

Function keys (DRPC-120-BTi-E5-OLED only)

The overview of the front panels of both model are shown in Figure 1-26 and Figure 1-3.

Figure 1-2: DRPC-120-BTi-E5-LED Front Panel


Page 5

Figure 1-3: DRPC-120-BTi-E5-OLED Front Panel

1.4.2 Top Panel

The DRPC-120-BTi top panel contains:

1 x 8-bit digital I/O (Phoenix terminal block, 4-bit input/4-bit output)

1 x 9 V ~ 28 V DC power terminal block

1 x AT/ATX power switch

1 x HDMI connector

1 x Power button

1 x Reset button

1 x VGA connector

An overview of the top panel is shown in 6Figure 1-4 below.


Page 6

Figure 1-4: DRPC-120-BTi Top Panel

1.5 LED Indicators (DRPC-120-BTi-E5-LED Only)

The LED indicators on the front panel of the DRPC-120-BTi-E5-LED are shown in

Figure 1-5.

Figure 1-5: LED Indicators of DRPC-120-BTi-E5-LED

All the LED definitions are listed in Table 1-2.

LED Color Status Description

On System power is on POWER Red

Off System power is off

HDD Green Blinking Storage device accessing


Page 7

Off Storage device not accessing

On COM port is transmitting data COM TX 1~4 Yellow

Off COM port is not transmitting data

On COM port is receiving data COM RX 1~4 Green

Off COM port is not receiving data

On Active DIO DI 1~4* Yellow

Off Inactive

On Active DIO DO 1~4* Green

Off Inactive

* When the DIO is set to pull-high, the DIO LED indicators always light up. When the DIO is set to pull-low, the DIO LED indicators are always off.

Table 1-2: DRPC-120-BTi-E5-LED LED Definitions

1.6 Programmable OLED Display (DRPC-120-BTi-E5-OLED Only)

For programming the OLED display on the front panel of the DRPC-120-BTi-E5-OLED,

refer to Chapter 6.

1.7 Technical Specifications

The DRPC-120-BTi technical specifications are listed in Table 1-3.

Specifications

System

CPU (SoC) 1.91 GHz quad-core Intel Atom E3845 processor

Memory One 2 GB 204-pin DDR3L SO-DIMM preinstalled

(system max. 8 GB)

Ethernet Controller One Intel I210 GbE controller

One Intel I211 GbE controller

Wireless 802.1b/g/n 1T1R (optional)

IPMI iRIS-2400 IPMI module (optional)

Supported OS Microsoft Windows 8,

Microsoft Windows Embedded Standard 7


Page 8

Specifications

Storage

HDD One 2.5 SATA 3Gb/s HDD/SSD bay

mSATA One PCIe Mini full-size card slot for mSATA module

(SATA 3Gb/s)

I/O and Indicators

Ethernet 2 x RJ-45 ports

RS-232 2 x DB-9 serial ports with 3KV isolation protection

RS-422/RS-485 2 x DB-9 serial ports with 3KV isolation protection

USB 2 x USB 3.0 ports

2 x USB 2.0 ports

Display Supports resolution up to 1920 x 1200

1 x VGA port

1 x HDMI port

Digital I/O 1 x Phoenix terminal block (8-bit, 4-bit input/4-bit output)

Interior Expansion 1 x PCIe Mini full-size card slot (co-lay mSATA)

1 x PCIe Mini half-size card slot (reserved for optional

Wi-Fi module)

Indicators LED (for DRPC-120-BTi-E5-LED)

OLED (for DRPC-120-BTi-E5-OLED)

Buttons Power button

Reset button

Power

Power Input 9 V ~ 28 V DC (3-pin terminal block)

Power Consumption [email protected] (1.91 GHz quad-core Intel Atom E3845

processor with 2 GB memory)

AT/ATX Mode AT/ATX switch

Environmental and Mechanical

Mounting DIN rail, desktop


Page 9

Specifications

Operating Temperature -20C~60C with air flow (with SSD)

Storage Temperature -30C~70C

Humidity 5%~95%, non-condensing

Chassis Construction Extruded aluminum alloy for fanless support

Color Blue C + Black C

Operating Shock Half-sine shock test 5G/11ms, 3 shocks per axis

Operating Vibration MIL-STD-810F 514.5 C-2 (SSD)

Safety CE/FCC

Weight (Net/Gross) 1.4 kg/2.5 kg

Physical Dimensions 74.8 mm x 140 mm x 171.5 mm (W x D x H)

Table 1-3: Technical Specifications


Page 10

1.8 Dimensions

The physical dimensions are shown below:

Figure 1-6: Physical Dimensions (millimeters)


Page 11

Chapter

2

2 Unpacking


Page 12

2.1 Anti-static Precautions

WARNING:

Failure to take ESD precautions during installation may result in

permanent damage to the DRPC-120-BTi and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the DRPC-120-BTi. Dry climates are especially susceptible to ESD. It is

therefore critical that whenever the DRPC-120-BTi or any other electrical component is

handled, the following anti-static precautions are strictly adhered to.

Wear an anti-static wristband: Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

Self-grounding: Before handling the board, touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.

Use an anti-static pad: When configuring the DRPC-120-BTi, place it on an

anti-static pad. This reduces the possibility of ESD damaging the

DRPC-120-BTi.

2.2 Unpacking Precautions

When the DRPC-120-BTi is unpacked, please do the following:

Follow the anti-static precautions outlined in Section 2.1.

Make sure the packing box is facing upwards so the DRPC-120-BTi does not

fall out of the box.

Make sure all the components shown in Section 2.3 are present.


Page 13

2.3 Unpacking Checklist

NOTE:

If some of the components listed in the checklist below are missing,

please do not proceed with the installation. Contact the IEI reseller or

vendor you purchased the DRPC-120-BTi from or contact an IEI sales

representative directly. To contact an IEI sales representative, please

send an email to [email protected]

The DRPC-120-BTi is shipped with the following components:

Quantity Item and Part Number Image

Standard

1 DRPC-120-BTi

or

1 3-pin terminal block

2 5-pin terminal block

1 SATA cable

(P/N: 32801-000702-100-RS)

1 SATA power cable

(P/N: 32102-010700-100-RS)

1 DIN rail mounting bracket

(50 mm x 45 mm x 8.7 mm)

mailto:[email protected]


Page 14

Quantity Item and Part Number Image

Standard

3 Mounting bracket screw

4 Screw (for securing an PCIe Mini card)

1 One Key Recovery CD

1 User manual and driver CD

The following table lists the optional items that can be purchased separately.

Optional

Power adapter

(P/N: 63000-FSP036RAB610-RS)

Power cord, European standard, 1830 mm

(P/N: 32000-000002-RS)

Power cord, American standard, 1830 mm

(P/N: 32000-000025-RS)

Power cable, DC jack (5.5x2.5) to 3-pin terminal

block, 200 mm

(P/N: 32102-026500-100-RS)


Page 15

Optional

Flash disk, mSATA, 2GB~32GB, 0C ~ 70C

(P/N: IPE-5200IM-xxx)

Flash disk, mSATA, 2GB~32GB, -40C ~ 85C

(P/N: IPE-5200VM-xxx)


Page 16

Chapter

3

3 Installation


Page 17

3.1 Installation Precautions

During installation, be aware of the precautions below:

Read the user manual: The user manual provides a complete description of

the DRPC-120-BTi, installation instructions and configuration options.

DANGER! Disconnect Power: Power to the DRPC-120-BTi must be

disconnected during the installation process. Failing to disconnect the power

may cause severe injury to the body and/or damage to the system.

Qualified Personnel: The DRPC-120-BTi must be installed and operated

only by trained and qualified personnel. Maintenance, upgrades, or repairs

may only be carried out by qualified personnel who are familiar with the

associated dangers.

Air Circulation: Make sure there is sufficient air circulation when installing the

DRPC-120-BTi. The DRPC-120-BTis cooling vents must not be obstructed by

any objects. Blocking the vents can cause overheating of the DRPC-120-BTi.

Leave at least 5 cm of clearance around the DRPC-120-BTi to prevent

overheating.

Grounding: The DRPC-120-BTi should be properly grounded. The voltage

feeds must not be overloaded. Adjust the cabling and provide external

overcharge protection per the electrical values indicated on the label attached

to the back of the DRPC-120-BTi.

3.1.1 High Surface Temperature

WARNING:

Some surfaces of the equipment may become hot during operation.

The surface temperature may be up to several tens of degrees hotter

than the ambient temperature. Under these circumstances, the

equipment needs to be protected against accidental contact.

The equipment is intended for installation in a RESTRICTED ACCESS LOCATION.


Page 18

Access can only be gained by SERVICE PERSONS or by USERS who have

been instructed about the reasons for the restrictions applied to the location

and about any precautions that shall be taken.

Access is through the use of a TOOL or lock and key, or other means of

security, and is controlled by the authority responsible for the location.

3.2 Internal Access Panel Removal

Before installing or maintaining the internal components, the internal access panel must

be removed from the DRPC-120-BTi. Follow the steps below to complete the task.

Step 1: Remove the three retention screws indicated in Figure 3-1.

Step 2: Slide the panel and gently lift the panel (Figure 3-1).

Figure 3-1: Internal Access Panel Removal

3.3 HDD Installation

The DRPC-120-BTi allows installation of one 2.5 HDD/SSD. To install a HDD into the

system, please follow the steps below.

Step 1: Remove the internal access panel from the DRPC-120-BTi. Please follow the

instruction described in Section 3.2.


Page 19

Step 2: Install the HDD into the bracket on the internal access panel, and secure the

HDD with four retention screws (Figure 3-2).

Step 3: Connect the SATA cable and the SATA power cable to the rear of the HDD

(Figure 3-2).

Step 4: Connect the SATA cable and the SATA power cable from the HDD to the SATA

connector and SATA power connector on the motherboard (Figure 3-2).

Figure 3-2: HDD Installation

Step 5: Replace and secure the internal access panel to the system.

3.4 mSATA SSD Installation

The DRPC-120-BTi has one full-size PCIe Mini slot on the motherboard for mSATA SSD

installation. To install the mSATA SSD, follow the instructions below.



Step 2: Locate the PCIe Mini slot on the motherboard (Figure 3-3).


Page 20

Figure 3-3: PCIe Mini Slot Location

Step 3: Insert into the socket at an angle. Line up the notch on the card with the notch

on the connector. Slide the PCIe Mini card into the socket at an angle of about

20 (Figure 3-4).

Figure 3-4: Inserting the PCIe Mini Card into the Socket

Step 4: Secure the PCIe Mini card. Secure the PCIe Mini card with the supplied

retention screws (Figure 3-5).


Page 21

Figure 3-5: Securing the PCIe Mini Card

Step 5: Replace and secure the internal access panel to the system. Step 0:

3.5 IPMI Module Installation (Optional)

NOTE:

The IPMI module slot is designed to install the IEI iRIS-2400 IPMI 2.0

module only. DO NOT install other modules into the IPMI module slot.

Doing so may cause damage to the DRPC-120-BTi.

Please follow the steps below to install the iRIS-2400 module, and refer to Section 3.10

for the setup procedure.



Step 2: Locate the IPMI module slot on the motherboard (Figure 3-3).


Page 22

Figure 3-6: IPMI Module Slot Location

Step 3: Align the iRIS-2400 module with the IPMI module slot. Align the notch on the

module with the notch on the IPMI module slot.

Step 4: Insert the iRIS-2400 module. Push the module in at a 20 angle (Figure 3-7).

Step 5: Seat the iRIS-2400 module. Gently push downwards and the arms clip into

place (Figure 3-7).

Figure 3-7: IPMI Module Installation

Step 6: Replace and secure the internal access panel to the system.


Page 23

3.6 Clear CMOS

If the DRPC-120-BTi fails to boot due to improper BIOS settings, the clear CMOS button

clears the CMOS data and resets the system BIOS information. To do this, push the clear

CMOS button for a few seconds.

If the CMOS Settings Wrong message is displayed during the boot up process, the fault

may be corrected by pressing the F1 to enter the CMOS Setup menu. Do one of the

following:

Enter the correct CMOS setting

Load Optimal Defaults

Load Failsafe Defaults.

After having done one of the above, save the changes and exit the CMOS Setup menu.

The clear CMOS button location is shown in 4Figure 3-8 below.

Figure 3-8: Clear CMOS Button Location


Page 24

3.7 AT/ATX Mode Selection

AT and ATX power modes can both be used on the DRPC-120-BTi. The selection is made

through an AT/ATX switch on the top panel as shown below (Figure 3-9).

Figure 3-9: AT/ATX Switch Location

3.8 Mounting the System

The DRPC-120-BTi embedded system can be mounted onto a DIN rail. Follow the steps

below to complete the task.

Step 1: Attach the supplied DIN rail mounting bracket to the rear panel of the embedded

system. Secure the bracket to the embedded system with three retention screws

(74Figure 3-10).

Figure 3-10: DIN Rail Mounting Bracket Installation


Page 25

NOTE:

In the diagrams below, the DIN rail is already installed on a surface or

on a chassis.

Step 2: Attach the upper edge of the mounting bracket to the DIN rail as shown in

Figure 3-11.

Figure 3-11: Attach the Mounting Bracket to the DIN Rail


Page 26

Step 3: Push the system toward the DIN rail until the mounting bracket clips into place

firmly (Figure 3-12).

Figure 3-12: Mounting the System

3.9 External Peripheral Interface Connectors

The DRPC-120-BTi has the following connectors. Detailed descriptions of the connectors

can be found in the subsections below.

8-bit DIO

Ethernet

Power input

RS-232

RS-422/485

USB

VGA

HDMI


Page 27

3.9.1 Digital Input/Output Terminal Block

CN Label: DIO

CN Type: Terminal block

CN Location: See Figure 1-4

CN Pinouts: See Table 3-1 and Figure 3-13

The digital I/O terminal block provides programmable input and output for external devices.

The digital I/O provides 4-bit output and 4-bit input. The pinouts for the digital I/O terminal

block are listed in the table below.

Pin Description Pin Description

1 DGI_0 2 DGO_0

3 DGI_1 4 DGO_1

5 DGI_2 6 DGO_2

7 DGI_3 8 DGO_3

9 Isolator GND 10 Isolator Vin

Table 3-1: DIO Terminal Block Pinouts

Figure 3-13: DIO Terminal Block Pinout Location

3.9.2 LAN Connectors

CN Type: RJ-45


CN Pinouts: See Table 3-2 and Table 3-3

The LAN connectors allow connection to an external network.


Page 28


20 LAN1_MDI0P 24 LAN1_MDI2P

21 LAN1_MDI0N 25 LAN1_MDI2N

22 LAN1_MDI1P 26 LAN1_MDI3P

23 LAN1_MDI1N 27 LAN1_MDI3N

Table 3-2: LAN1 Pinouts


P2 TRD2P0 P6 TRD2P2

P3 TRD2N0 P7 TRD2N2

P4 TRD2P1 P8 TRD2P3

P5 TRD2N1 P9 TRD2N3

Table 3-3: LAN2 Pinouts

Figure 3-14: RJ-45 Ethernet Connector

The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green

LED indicates activity on the port and the yellow LED indicates the port is linked. See

Table 3-4.

Activity/Link LED Speed LED

STATUS DESCRIPTION STATUS DESCRIPTION

Off No link Off 10 Mbps connection

Yellow Linked Green 100 Mbps connection

Blinking TX/RX activity Orange 1 Gbps connection

Table 3-4: RJ-45 Ethernet Connector LEDs


Page 29

3.9.3 Power Input, 3-pin Terminal Block

CN Type: 3-pin terminal block



Connect the leads of a 9 V ~ 28 V DC power supply into the terminal block. Make sure that

the power and ground wires are attached to the correct sockets of the connector.


1 9V~28V input 3 GND

2 9V~28V input

Table 3-5: 3-pin Power Terminal Block Pinouts

Figure 3-15: 3-pin Power Terminal Block Pinout Location


Page 30

3.9.4 RS-232 Serial Port Connectors (COM1, COM2)

CN Label: COM1 and COM2

CN Type: DB-9 connectors



RS-232 serial port devices can be attached to the DB-9 ports on the front panel.


1 DCD 6 DSR

2 RXD 7 RTS

3 TXD 8 CTS

4 DTR 9 RI

5 GND

Table 3-6: RS-232 Serial Port Pinouts

Figure 3-16: RS-232 Serial Port Pinout Location


Page 31

3.9.5 RS-422/485 Serial Port Connectors (COM3, COM4)

CN Label: COM3 and COM4

CN Type: DB-9 connectors



RS-422/485 serial port devices can be attached to the DB-9 ports on the front panel.

Pin RS-422 RS-485

1 RS-422TX- RS-485D-

2 RS-422TX+ RS-485D+

3 RS-422RX+ --

4 RS-422RX- --

5 GND --

6 -- --

7 -- --

8 -- --

9 -- --

Table 3-7: RS-422/485 Serial Port Pinouts

Figure 3-17: RS-422/485 Serial Port Pinout Locations


Page 32

3.9.6 USB Connectors

CN Type: USB port


CN Pinouts: See Table 3-8 and Table 3-9

The USB ports are for connecting USB peripheral devices to the system. The USB 2.0 and

USB 3.0 connector pinouts are listed below.


1 VCC 5 VCC

2 DATA- 6 DATA-

3 DATA+ 7 DATA+

4 GROUND 8 GROUND

Table 3-8: USB 2.0 Port (USB3/USB4) Pinouts


1 VCC 10 VCC

2 USB_DATA- 11 USB_DATA-

3 USB_DATA+ 12 USB_ DATA+

4 GND 13 GND

5 USB3_RX- 14 USB3_RX-

6 USB3_RX+ 15 USB3_ RX+

7 GND 16 GND

8 USB3_TX- 17 USB3_TX-

9 USB3_TX+ 18 USB3_TX+

Table 3-9: USB 3.0 Port (USB1/USB2) Pinouts


Page 33

3.9.7 VGA Connector

CN Label: VGA

CN Type: 15-pin Female


CN Pinouts: See Table 3-10

The VGA connector connects to a monitor that accepts VGA video input.


1 RED 2 GREEN

3 BLUE 4 NC

5 GND 6 GND

7 GND 8 GND

9 VCC 10 GND

11 NC 12 DDC DAT

13 HSYNC 14 VSYNC

15 DDCCLK

Table 3-10: VGA Connector Pinouts

Figure 3-18: VGA Connector

3.10 IPMI Setup Procedure

The DRPC-120-BTi features Intelligent Platform Management Interface (IPMI) that helps

lower the overall costs of server management by enabling users to maximize IT resource,

save time and manage multiple systems. The DRPC-120-BTi supports IPMI 2.0 through

the optional iRIS-2400 module. Follow the steps below to setup IPMI.


Page 34

3.10.1 Managed System Hardware Setup

The hardware configuration of the managed system (DRPC-120-BTi) is described below.

Step 1: Install an iRIS-2400 module to the IPMI module socket (refer to Section 3.5).

Step 2: Make sure at least one DDR3 SO-DIMM is installed in one of the SO-DIMM

sockets. If multiple SO-DIMMs are installed, all of the SO-DIMMs must be same

size, same speed and same brand to get the best performance.

Step 3: Connect an Ethernet cable to LAN2 RJ-45 connector (Figure 1-2).

3.10.2 Using the IEI iMAN Web GUI

To manage a client system from a remote console using IEI iMAN Web GUI, follow the

steps below.

Step 1: Obtain the IP address of the managed system. It is recommended to use the

IPMI Tool on the managed system to obtain the IP address. To use IPMI Tool to

obtain IP address, follow the steps below:

a. Copy the Ipmitool.exe file to a bootable USB flash drive.

b. Insert the USB flash drive to the DRPC-120-BTi.

c. The DRPC-120-BTi boots from the USB flash drive.

d. Enter the following command: ipmitool 20 30 02 01 03 00 00

(there is a space between each two-digit number).

e. A serial of number shows. The last four two-digit hexadecimal numbers are

the IP address. Convert the hexadecimal numbers to decimal numbers.

Step 2: On the remote management console, open a web browser. Enter the managed

system IP address in the web browser (Figure 3-19).

Figure 3-19: IEI iMAN Web Address

Step 3: The login page appears in the web browser.


Page 35

Step 4: Enter the user name and password to login the system. The default login

username and password are:

-Username: admin

-Password: admin

Step 5: Press the login button to login the system.

Step 6: The IEI iMAN Web Interface appears. Step 0:

Figure 3-20: IEI iMAN Web GUI

NOTE:

To understand how to use the IEI iMAN Web GUI, please refer to the

iRIS-2400 Web GUI user manual in the utility CD came with the

DRPC-120-BTi. The user manual describes each function in detail.


Page 36

3.11 Driver Installation

NOTE:

The content of the CD may vary throughout the life cycle of the product

and is subject to change without prior notice. Visit the IEI website or

contact technical support for the latest updates.

All the drivers for the DRPC-120-BTi are on the utility CD that came with the system. The

utility CD contains drivers for Windows 7 and Windows 8 operating systems. Please select

the corresponding drivers for the system.

The following drivers can be installed on the Windows 7 operating system:

Chipset

I/O driver

Graphics (Intel EMGD)

TXE

USB 3.0

LAN

Audio

The following drivers can be installed on the Windows 8 operating system:

Chipset

Serial I/O driver (64-bit only)

TXE

Graphics

LAN

Audio

The DRPC-120-BTi-E5-OLED also comes with two programmable OLED display utilities

that allow users to program their own APIs to show information on the OLED screen in

graphic and text formats. Please refer to Chapter 6 for detailed instruction.


Page 37

Chapter

4

4 System Maintenance


Page 38

4.1 System Maintenance Introduction

The following system components may require maintenance.

Motherboard

SO-DIMM module

If these components fail, they must be replaced. Please contact the system reseller or

vendor to purchase replacement parts. Replacement instructions for the above listed

components are described below.

WARNING!

Before accessing any DRPC-120-BTi internal components, make sure

all power to the system has been disconnected. Failing to do so may

cause severe damage to the DRPC-120-BTi and injury to the user.

WARNING!

Please take antistatic precautions when working with the internal

components. The interior of the DRPC-120-BTi contains very sensitive

electronic components. These components are easily damaged by

electrostatic discharge (ESD). Before working with the internal

components, make sure all anti-static precautions described earlier

have been observed.

4.2 Motherboard Replacement

A user cannot replace a motherboard. If the motherboard fails it must be shipped back to

IEI to be replaced. If the system motherboard has failed, please contact the system vendor,

reseller or an IEI sales person directly.


Page 39

4.3 SO-DIMM Replacement

To install/replace the SO-DIMM modules, please follow the steps below.



Step 2: Locate the SO-DIMM module on the motherboard.

Figure 4-1: SO-DIMM Module Location

Step 3: Release the SO-DIMM module by pulling both the spring retainer clips outward

from the socket.

Step 4: Grasp the SO-DIMM module by the edges and carefully pull it out of the socket.

Step 5: Install the new SO-DIMM module by pushing it into the socket at an angle

(Figure 4-2).

Step 6: Gently push the rear of the SO-DIMM module down (Figure 4-2). The spring

retainer clips clip into place and secure the SO-DIMM module in the socket.


Page 40

Figure 4-2: SO-DIMM Module Installation

Step 7: Push the new SO-DIMM module until it engages and the white plastic end clips

click into place. Make sure the end clips are fully secured after installation.Step 0:


Page 41

Chapter

5

5 BIOS


Page 42

5.1 Introduction

The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to

certain system settings. This chapter outlines the options that can be changed.

NOTE:

Some of the BIOS options may vary throughout the life cycle of the

product and are subject to change without prior notice.

5.1.1 Starting Setup

The UEFI BIOS is activated when the computer is turned on. The setup program can be

activated in one of two ways.

1. Press the DEL or F2 key as soon as the system is turned on or

2. Press the DEL or F2 key when the Press DEL or F2 to enter SETUP

message appears on the screen.

If the message disappears before the DEL or F2 key is pressed, restart the computer and

try again.

5.1.2 Using Setup

Use the arrow keys to highlight items, press ENTER to select, use the PageUp and

PageDown keys to change entries, press F1 for help and press ESC to quit. Navigation

keys are shown in Table 5-1.

Key Function

Up arrow Move to previous item

Down arrow Move to next item

Left arrow Move to the item on the left hand side

Right arrow Move to the item on the right hand side

+ Increase the numeric value or make changes


Page 43

Key Function

- Decrease the numeric value or make changes

Esc key Main Menu Quit and not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu --

Exit current page and return to Main Menu

F1 key General help, only for Status Page Setup Menu and Option

Page Setup Menu

F2 key Load previous values

F3 key Load optimized defaults

F4 key Save changes and exit BIOS

Table 5-1: BIOS Navigation Keys

5.1.3 Getting Help

When F1 is pressed a small help window describing the appropriate keys to use and the

possible selections for the highlighted item appears. To exit the Help Window press ESC or

the F1 key again.

5.1.4 Unable to Reboot after Configuration Changes

If the computer cannot boot after changes to the system configuration is made, CMOS

defaults. Use the clear CMOS button described in Chapter 3.

5.1.5 BIOS Menu Bar

The menu bar on top of the BIOS screen has the following main items:

Main Changes the basic system configuration.

Advanced Changes the advanced system settings.

Chipset Changes the chipset settings.

Security Sets User and Supervisor Passwords.

Boot Changes the system boot configuration.

Save & Exit Selects exit options and loads default settings


Page 44

The following sections completely describe the configuration options found in the menu

items at the top of the BIOS screen and listed above.

5.2 Main

The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered.

The Main menu gives an overview of the basic system information.

Aptio Setup Utility Copyright (C) 2013 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit

BIOS Information BIOS Vendor American Megatrends Core Version 5.009 Compliancy UEFI 2.3;PI1.2 Project Version E445AT13.ROM Build Date and Time 09/18/2014 10:57:55 iWDD Vendor iEi iWDD Version E445ET18.bin IPMI Module N/A CPU Configuration Microcode Patch 901 BayTrail SoC D0 Stepping Memory Information Total Memory 2048 MB (LPDDR3) GOP Information Intel(R) GOP Driver [N/A] TXE Information Sec RC Version 00.05.00.00 TXE FW Version 01.00.02.1060 System Date [Tue 01/02/2010] System Time [15:10:27]

Set the Date. Use Tab to switch between Data elements. ---------------------- : Select Screen : Select Item Enter Select + -: Change Opt. F1: General Help F2: Previous Values F3: Optimized DefaultsF4: Save & Exit ESC: Exit

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. BIOS Menu 1: Main

BIOS Information

The BIOS Information lists a brief summary of the BIOS. The fields in BIOS Information

cannot be changed. The items shown in the system overview include:

BIOS Vendor: Installed BIOS vendor


Page 45

Core Version: Current BIOS version

Compliancy: Current compliant version

Project Version: the board version

Build Date and Time: Date and time the current BIOS version was made

iWDD Vendor: Installed embedded controller vendor

iWDD Version: Current embedded controller version

IPMI Module

The IPMI Module lists the installed IPMI module information.

CPU Information

The CPU Information lists a brief summary of the CPU. The fields in CPU Information

cannot be changed. The items shown in the system overview include:

Microcode Patch: Installed microcode patch

BayTrail SoC: CPU stepping level

Memory Information

The Memory Information lists a brief summary of the system memory. The fields in

Memory Information cannot be changed. The items shown in the system overview

include:

Total Memory: Current total memory of the system

GOP Information

The GOP Information lists a brief summary of the Graphics Output Protocol (GOP). The

fields in GOP Information cannot be changed. The items shown in the system overview

include:

Intel GOP Driver: Installed Intel GOP driver


Page 46

TXE Information

The TXE Information lists a brief summary of Intel Trusted Execution Engine (TXE).

The fields in TXE Information cannot be changed. The items shown in the system

overview include:

Sec RC Version: Current sec reference code version

TXE FW Version: Current Intel TXE firmware version

The System Overview field has two user configurable fields:

System Date [xx/xx/xx]

Use the System Date option to set the system date. Manually enter the day, month and

year.

System Time [xx:xx:xx]

Use the System Time option to set the system time. Manually enter the hours, minutes

and seconds.

5.3 Advanced

Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices

through the following sub-menus:

WARNING!

Setting the wrong values in the sections below may cause the system

to malfunction. Make sure that the settings made are compatible with

the hardware.


Page 47

Aptio Setup Utility Copyright (C) 2013 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit

> ACPI Settings > Super IO Configuration > iWDD H/W Monitor > RTC Wake Settings > Serial Port Console Redirection > CPU Configuration > IDE Configuration > USB Configuration > ICP Board

System ACPI Parameters ---------------------- : Select Screen : Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized DefaultsF4 Save & Exit ESC Exit

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. BIOS Menu 2: Advanced

5.3.1 ACPI Settings

The ACPI Settings menu (BIOS Menu 3) configures the Advanced Configuration and

Power Interface (ACPI) options.

Aptio Setup Utility Copyright (C) 2013 American Megatrends, Inc. Advanced

ACPI Settings ACPI Sleep State [S3 (Suspend to RAM)]

Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed. ---------------------- : Select Screen : Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized DefaultsF4 Save & Exit ESC Exit

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. BIOS Menu 3: ACPI Configuration


Page 48

ACPI Sleep State [S3 (Suspend to RAM)]

Use the ACPI Sleep State option to specify the sleep state the system enters when it is

not being used.

S3 (Suspend to RAM)

DEFAULT The caches are flushed and the CPU is powered

off. Power to the RAM is maintained. The

computer returns slower to a working state, but

more power is saved.

5.3.2 Super IO Configuration

Use the Super IO Configuration menu (BIOS Menu 4) to set or change the

configurations for the serial ports.


F81866 Super IO Configuration F81866 Super IO Chip F81866 > Serial Port 1 Configuration > Serial Port 2 Configuration > Serial Port 3 Configuration > Serial Port 4 Configuration

Set Parameters of Serial Port 1 (COMA) --------------------- : Select Screen : Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized DefaultsF4 Save & Exit ESC Exit

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. BIOS Menu 4: Super IO Configuration


Page 49

5.3.2.1 Serial Port n Configuration

Use the Serial Port n Configuration menu (BIOS Menu 5) to configure the serial port n.


Serial Port n Configuration Serial Port [Enabled] Device Settings IO=3F8h;IRQ=4 Change Settings [Auto]

Enable or Disable Serial Port (COM) --------------------- : Select Screen : Select Item Enter Select = - Change Opt. F1 General Help F2 Previous Values F3 Optimized DefaultsF4 Save & Exit ESC Exit

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. BIOS Menu 5: Serial Port n Configuration Menu

5.3.2.1.1 Serial Port 1 Configuration

Serial Port [Enabled]

Use the Serial Port option to enable or disable the serial port.

Disabled Disable the serial port

Enabled DEFAULT Enable the serial port

Change Settings [Auto]

Use the Change Settings option to change the serial port IO port address and interrupt

address.

Auto DEFAULT The serial port IO port address and interrupt address are automatically detected.

IO=3F8h; IRQ=4

Serial Port I/O port address is 3F8h and the interrupt

address is IRQ4


Page 50

IO=3F8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

IO=2F8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

IO=3E8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12

Serial Port I/O port address is 3E8h and the interrupt

address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

IO=2E8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12








address.



Page 51

IO=2F8h; IRQ=3


address is IRQ3

IO=3F8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

IO=2F8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

IO=3E8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

IO=2E8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12








address.


Page 52


IO=3E8h; IRQ=7


address is IRQ7

IO=3F8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

IO=2F8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

IO=3E8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

IO=2E8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

IO=2F0h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

IO=2E0h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12


Page 53








address.


IO=2E8h; IRQ=7


address is IRQ7

IO=3F8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

IO=2F8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

IO=3E8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

IO=2E8h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12


Page 54

IO=2F0h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

IO=2E0h; IRQ=3, 4,

5, 6, 7, 9,

10, 11, 12


address is IRQ3, 4, 5, 6, 7, 9, 10, 11, 12

5.3.3 iWDD H/W Monitor

The iWDD H/W Monitor menu (BIOS Menu 6) contains the fan configuration submenus

and displays operating temperature and system voltages.


PC Health Status CPU temperature :+43 C System temperature :+39 C CPU_FAN1 Speed :N/A CPU_CORE :+0.886 V +5V :+4.968 V +V12 :+11.866 V +DDR :+1.342 V +5VSB :+4.953 V +3.3V :+3.291 V +3.3VSB :+3.271 V > Smart Fan Mode Configuration

Smart Fan Mode Select --------------------- : Select Screen : Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized DefaultsF4 Save & Exit ESC Exit

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. BIOS Menu 6: iWDD Hardware Monitor

PC Health Status

The following system parameters and values are shown. The system parameters that are

monitored are:


Page 55

System Temperatures:

o CPU Temperature o System Temperature

Fan Speed:

o CPU Fan Voltages:

o CPU_CORE o +5V o +V12 o +DDR o +5VSB o +3.3V o +3.3VSB

5.3.3.1 Smart Fan Mode Configuration

Use the Smart Fan Mode Configuration submenu (BIOS Menu 7) to configure smart fan

temperature and speed settings.


Smart Fan Mode Configuration CPU_FAN1 Smart Fan Control [Auto Mode] Auto mode fan start temperature 50 Auto mode fan off temperature 40 Auto mode fan start PWM 30 Auto mode fan slope PWM 1

Smart Fan Mode Select --------------------- : Select Screen : Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized DefaultsF4 Save & Exit ESC Exit

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. BIOS Menu 7: Smart Fan Function

CPU Smart Fan Control [Auto PWM Mode]

Use the CPU Smart Fan Control option to configure the CPU smart fan.


Page 56

Manual Mode The fan spins at the speed set in Manual Mode settings.

Auto Mode DEFAULT The fan adjusts its speed using Auto Mode settings.

Auto mode fan start temperature

Use the + or key to change the Auto mode fan start temperature value. Enter a

decimal number between 1 and 100.

Auto mode fan off temperature

Use the + or key to change the Auto mode fan off temperature value. Enter a decimal

number between 1 and 100.

Auto mode fan start PWM

Use the + or key to change the Auto mode fan start PWM value. Enter a decimal


Auto mode fan slope PWM

Use the + or key to change the Auto mode fan slope PWM value. Enter a decimal



Page 57

5.3.4 RTC Wake Settings

The RTC Wake Settings menu (BIOS Menu 8) configures RTC wake event.


Wake System with Fixed Time [Disabled]

Enables or Disables system wake on alarm event. When enabled, system will wake on the date: hr: min: sec specified. ---------------------- : Select Screen : Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized DefaultsF4 Save & Exit ESC Exit

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. BIOS Menu 8: RTC Wake Settings

Wake System with Fixed Time [Disabled]

Use the Wake System with Fixed Time option to specify the time the system should be

roused from a suspended state.

Disabled DEFAULT The real time clock (RTC) cannot generate a wake event


Page 58

Enabled If selected, the following appears with values that can be selected:

*Wake up every day

*Wake up date

*Wake up hour

*Wake up minute

*Wake up second

After setting the alarm, the computer turns itself on

from a suspend state when the alarm goes off.

5.3.5 Serial Port Console Redirection

The Serial Port Console Redirection menu (BIOS Menu 9) allows the console

redirection options to be configured. Console redirection allows users to maintain a

system remotely by re-directing keyboard input and text output through the serial port.


COM1 Console Redirection [Disabled]

> Console Redirection Settings COM2 Console Redirection [Disabled]



> Console Redirection Settings COM5 (BMC) Console Redirection [Disabled]

> Console Redirection Settings

Console Redirection Enable or Disable --------------------- : Select Screen : Select Item Enter Select +/-: Change Opt. F1 General Help F2 Previous Values F3 Optimized DefaultsF4 Save & Exit ESC Exit

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. BIOS Menu 9: Serial Port Console Redirection


Page 59

Console Redirection [Disabled]

Use Console Redirection option to enable or disable the console redirection function.

Disabled DEFAULT Disabled the console redirection function

Enabled Enabled the console redirection function

The following options are available in the Console Redirection Settings submenu when

the Console Redirection option is enabled.

Terminal Type [ANSI]

Use the Terminal Type option to specify the remote terminal type.

VT100 The target terminal type is VT100

VT100+ The target terminal type is VT100+

VT-UTF8 The target terminal type is VT-UTF8

ANSI DEFAULT The target terminal type is ANSI

Bits per second [115200]

Use the Bits per second option to specify the serial port transmission speed. The speed

must match the other side. Long or noisy lines may require lower speeds.

9600 Sets the serial port transmission speed at 9600.




115200 DEFAULT Sets the serial port transmission speed at 115200.

Data Bits [8]

Use the Data Bits option to specify the number of data bits.

7 Sets the data bits at 7.


Page 60

8 DEFAULT Sets the data bits at 8.

Parity [None]

Use the Parity option to specify the parity bit that can be sent with the data bits for

detecting the transmission errors.

None DEFAULT No parity bit is sent with the data bits.

Even The parity bit is 0 if the number of ones in the data bits is even.

Odd The parity bit is 0 if the number of ones in the data bits is odd.

Mark The parity bit is always 1. This option does not provide error detection.

Space The parity bit is always 0. This option does not provide error detection.

Stop Bits [1]

Use the Stop Bits option to specify the number of stop bits used to indicate the end of a

serial data packet. Communication with slow devices may require more than 1 stop bit.

1 DEFAULT Sets the number of stop bits at 1.

2 Sets the number of stop bits at 2.

5.3.6 CPU Configuration

Use the CPU Configuration BIOS menu (BIOS Menu 10) to view detailed CPU

specifications and configure the CPU.


Page 61


CPU Configuration Intel(R) Celeron(R) CPU E3845 @ 1.91GHz CPU Signature 30679 Microcode Patch 901 Max CPU Speed 1910 MHz Min CPU Speed 500 MHz Processor Cores 4 Intel HT Technology Not Supported Intel VT-x Technology Supported L1 Data Cache 24 kB x 4 L1 Code Cache 32 kB x 4 L2 Cache 1024 kB x 2 L3 Cache Not Present 64-bit Supported Intel Virtualization Technology [Enabled] EIST [Enabled]

Number enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology. ---------------------- : Select Screen : Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized DefaultsF4 Save & Exit ESC Exit

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. BIOS Menu 10: CPU Configuration

The CPU Configuration menu (BIOS Menu 10) lists the following CPU details:

CPU Signature: Lists the CPU signature value.

Microcode Patch: Lists the microcode patch being used.

Max CPU Speed: Lists the maximum CPU processing speed.

Min CPU Speed: Lists the minimum CPU processing speed.

Processor Cores: Lists the number of the processor core

Intel HT Technology: Indicates if Intel HT Technology is supported by the

CPU.

Intel VT-x Technology: Indicates if Intel VT-x Technology is supported by the

CPU.

L1 Data Cache: Lists the amount of data storage space on the L1 cache.

L1 Code Cache: Lists the amount of code storage space on the L1 cache.

L2 Cache: Lists the amount of storage space on the L2 cache.

L3 Cache: Lists the amount of storage space on the L3 cache.


Page 62

Intel Virtualization Technology [Enabled]

Use the Intel Virtualization Technology option to enable or disable virtualization on the

system. When combined with third party software, Intel Virtualization technology allows

several OSs to run on the same system at the same time.

Disabled Disables Intel Virtualization Technology.

Enabled DEFAULT Enables Intel Virtualization Technology.

EIST [Enabled]

Use the EIST option to enable or disable Enhanced Intel SpeedStep Technology (EIST).

Disabled Disables Enhanced Intel SpeedStep Technology.

Enabled DEFAULT Enables Enhanced Intel SpeedStep Technology.


Page 63

5.3.7 IDE Configuration

Use the IDE Configuration menu (BIOS Menu 11) to change and/or set the configuration

of the SATA devices installed in the system.


IDE Configuration Serial-ATA (SATA) [Enabled] SATA Mode [IDE Mode] SATA Port1 Not Present SATA Port2 Not Present

Select IDE / AHCI --------------------- : Select Screen : Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized DefaultsF4 Save & Exit ESC Exit

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. BIOS Menu 11: IDE Configuration

Serial-ATA (SATA) [Enabled]

Use the Serial-ATA (SATA) option to enable or disable the serial ATA port.

Enabled DEFAULT Enables the SATA port.

Disabled Disables the SATA port.

SATA Mode [IDE Mode]

Use the SATA Mode option to configure SATA devices as normal IDE devices.

IDE Mode DEFAULT Configures SATA devices as normal IDE device.

AHCI Mode Configures SATA devices as AHCI device.


Page 64

5.3.8 USB Configuration

Use the USB Configuration menu (BIOS Menu 12) to read USB configuration

information and configure the USB settings.


USB Configuration USB Devices: 1 Keyboard, 2 Hubs Legacy USB Support [Enabled]

Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications. --------------------- : Select Screen : Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized DefaultsF4 Save & Exit ESC Exit

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. BIOS Menu 12: USB Configuration

USB Devices

The USB Devices Enabled field lists the USB devices that are enabled on the system

Legacy USB Support [Enabled]

Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard

does not become available until a USB compatible operating system is fully booted with all

USB drivers loaded. When this option is enabled, any attached USB mouse or USB

keyboard can control the system even when there is no USB driver loaded onto the

system.

Enabled DEFAULT Legacy USB support enabled


Page 65

Disabled Legacy USB support disabled

Auto Legacy USB support disabled if no USB devices are connected

5.4 Chipset

Use the Chipset menu (BIOS Menu 13) to access the North Bridge and South Bridge

subsystem configuration menus.

WARNING!

Setting the wrong values for the Chipset BIOS selections in the Chipset

BIOS menu may cause the system to malfunction.

Aptio Setup Utility Copyright (C) 2013 American Megatrends, Inc.

Main Advanced Chipset Security Boot Save & Exit > North Bridge > South Bridge

North Bridge Parameters. --------------------- : Select Screen : Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized DefaultsF4 Save & Exit ESC Exit

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. BIOS Menu 13: Chipset


Page 66

5.4.1 North Bridge

Use the North Bridge menu (BIOS Menu 14) to configure the north bridge parameters.

Aptio Setup Utility Copyright (C) 2013 American Megatrends, Inc. Chipset

Memory Information Total Memory 2048 MB (LPDDR3) DIMM1 2048 MB (LPDDR3)

--------------------- : Select Screen : Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized DefaultsF4 Save & Exit ESC Exit

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. BIOS Menu 14: North Bridge

5.4.2 South Bridge

Use the South Bridge menu (BIOS Menu 15) to configure the south bridge parameters.


Auto Power Button Function [Disabled (ATX)] Restore AC Power Loss [Last State] > PCI Express Configuration Audio Configuration Audio Controller [Enabled] USB Configuration USB 2.0(EHCI) Support [Disabled] XHCI Mode [Smart Auto]

Select AC power state when power is re-applied after a power failure. --------------------- : Select Screen : Select Item Enter Select + - Change Opt. F1 General Help F2 Previous Values F3 Optimized DefaultsF4 Save & Exit ESC Exit

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. BIOS Menu 15: South Bridge


Page 67

Restore on AC Power Loss [Last State]

Use the Restore on AC Power Loss BIOS option to specify what state the system

returns to if there is a sudden loss of power to the system.

Power Off The system remains turned off

Power On The system turns on

Last State DEFAULT The system returns to its previous state. If it was on, it turns itself on. If it was off, it remains off.

Audio Controller [Enabled]

Use the Audio Controller BIOS option to enable or disable the High Definition Audio

controller.

Disabled The High Definition Audio controller is disabled.

Enabled DEFAULT The High Definition Audio controller is enabled.

XHCI Mode [Smart Auto]

Use the XHCI Mode BIOS option to configure the USB xHCI (USB 3.0) controller.

Enabled Enable the xHCI controller. USB 3.0 ports behave as USB 3.0 ports.

Smart Auto

DEFAULT Allow the use of USB 3.0 devices prior to OS boot.

USB 3.0 ports function as USB 3.0 ports even during a

reboot.


Page 68

5.4.2.1 PCI Express Configuration

Use the PCI Express Configuration submenu (BIOS Menu 16) to configure the PCI

Express slots.


PCI Express Configuration PCI Express Port 2 [Enabled] Speed [Auto]

Enable or Disable the PCI Express P

Documents

DRPC-120-BTi Embedded System - ICP America · DRPC-120-BTi Embedded System Page i User Manual MODEL: DRPC-120-BTi Fanless Embedded System with Intel® Atom™ E3845 CPU, ... 36 4