Issue November 27, 2006

PRIMERGY Zero Channel RAID Contr. MegaRAID SAS 8300XLP (LSI Logic Corp.) Pages 2

MegaRAID® SAS 8300XLP Zero Channel RAID Controller (ZCR). The PRIMERGY ZCR SAS RAID controller from LSI Logic Corporation (MegaRAID® SAS 8300XLP) offers powerful data throughput, extensive fault-tolerant capabilities, and easy-to-use management. Key features: • Industry proven MegaRAID® data protection • Flexibility for both SAS and SATA II • Advanced management and configuration suits • Supports RAID level 0, 1 5, 10 and 50 • 128 MB cache optional with BBU saved • Offers advanced MegaRAID functionality to onboard LSI

SAS Low-Cost, Powerful ZCR SAS RAID Solution The MegaRAID SAS 8300XLP zero-channel RAID (ZCR) adapter converts a motherboard’s own onboard Serial Attached SCSI (SAS) con-troller into a powerful RAID solution, allowing for an easy and low-cost upgrade path to SAS RAID. This low profile, intelligent PCI-X to SAS RAID adapter is ideal for 1U and 2U server environments. With 128MB integrated ECC SDRAM, optional battery backup support and the power of the Intel® IOP321 (400MHz) I/O processor, the MegaRAID SAS 8300XLP provides unmatched reliability and performance. Motherboard Compatibility The MegaRAID SAS 8300XLP adapter is designed to use a motherboard’s own on-board SAS ports using the LSI Logic LSI SAS1068 SAS initiator controller with appropriate interrupt routing circuitry. The PRIMERGY servers TX150 S5, TX200 S3 and RX200 S3 have the appropriate logic on the motherboard to support this controller

RAID performance The MegaRAID® SAS 8300XLP (ZCR SAS) offers maximum I/O performance and data throughput by leveraging a stable and proven RAID firmware. The MegaRAID® SAS 8300XLP benefits from a streamlined firmware level programming interface and advanced hardware designs for enhanced I/O efficiency and performance. Through support for 64-bit addressing, a robust RAID feature set, and advanced fault tolerance capabilities, the MegaRAID® SAS 8300XLP delivers high RAID performance and data availability. Powerful online management utilities (LSI based GAM and FSC's ServerView RAID) that are easy to use and quick to install allow administrators unequalled array flexibility and accessibility. Optional BBU Support The optional battery-backup module protects the integrity of the cached data on a MegaRAID controller by providing backup power if there is a complete AC power failure or a brief power outage. The battery backup units provide an inexpensive alternative to using an uninterruptible power supply (UPS)

Data Sheet ⏐ Issue: November 27, 2006⏐ PRIMERGY ZCR SAS RAID Controller (LSI) Page 2 / 2

All rights, including rights created by patent grant or registration of a utility model or design as well as rights of technical modifications are reserved. Delivery subject to availability. Designations may be trademarks, the use of which by third parties for their own purposes may violate the rights of the trademark owners.

Copyright © Fujitsu, 11/2006

Published by

Fujitsu http://ts.fujitsu.com/

Company stamp

Controller specifications Processor Intel® Xscale™ IOP80321 PCI PCI 2.2 and PCI-X 1.0

64 Bit, 100 MHz (ZCR-enabled slot only)

Cache 128 MB DDR SDRAM (with ECC)

Battery Backup Unit yes (optional BBU) Drives per controller n/a

Technical specifications PCI Card low profile, half length

(16.8cm x 6,5cm) Power Requirements 3.3 V, 5V, +12V, -12V Certification ISO 9001 SAS specification

Use a SAS chip on the motherboard Supports 8 port (SAS1068) LSI SAS chips. The controller contains no SAS interface connector.

The number of drives is depending to the system design. In all PRIMERGY designs each disk drive is connected to a dedicated SAS port. max. capacity per array:

greater than 2 TB max. capacity per LUN: 2 TB

RAID Fault Tolerant- and Flexibility-Features RAID levels 0, 1, 5, 10 and 50 supported Online Capacity Expansion (OCE)

(only supported with one logical drive per RAID array) Online RAID level migration (RLM) Variable Stripe Size for all logical drives Fast initialization for quick array setup Advanced error recognition of drives (Patrol Read) Background initialization for RAID 1, 5, 10 and 50 Several logical drives per RAID cluster possible Hot spare dives configurable Independent cache administration method per logical drive ° Write-back/Write-through ° Read-ahead: Disable / Enable / Adaptive ° Cached I/O / Direct I/O

up to 64 Logical drives per controller

Fault Tolerant COD – Configuration on disk and NVRAM Auto detection of failed drives Automatic rebuild of hot-plug drives Battery Backup cache memory Support for SAT-TE enclosure management S.M.A.R.T monitoring

Supported Operating Systems

Windows 2000, 2003 (Microsoft Linux (SuSE, Red Hat) VMware ESX 3.x

Compliance with Norm and Standards Product safety

Global IEC 60950 Europe EN 60950 USA / Canada CSA 60950 Europe CAN 60950

Electro magnetic compatibility

Europe EN55022, EN55024 Taiwan BSMI Class B Japan VCCI Korea RRL for MIC China CCC Australian C-tick USA / Canada FCC Part 15 Class B, ICES-003

Conformity process Europe (CE) EN Class B North America FCC Class B

Approvals Product safety

Global Europe CE Germany USA / Canada CSA

There is general compliance with the safety requirements of all European countries and North America. National approvals required in order to satisfy statutory regulations or for other reasons (e.g. for Canada and USA, East European countries, Norway), can be applied for on request.