DTV 742 - WEGENER · 2006-11-29 · DTV 742 User’s Manual 800057-01 Rev. C 2 1.2 DTV742 Overview The DTV 742 8VSB 4-Channel Multiplexer (Figure1.1) receives VHF/UHF broadcast HDTV

800057-02 Rev. C

DTV 742

8VSB 4-Channel Multiplexer

User’s Manual

DTV 742 User’s Manual

800057-01 Rev. C ii www.wegener.com

A proven world leader in digital video, audio & broadcast data systems, WEGENER’smanagement system is certified to ISO 9001:2000.

Data, drawings, and other material contained herein are proprietary to Wegener Com-munications, Inc., and may not be reproduced or duplicated in any form without theprior written permission of Wegener Communications, Inc.

The information contained herein is subject to change without notice. Revisions maybe issued to advise of such changes and/or additions.

2004 Wegener Communications, Inc. All rights reserved.

WEGENER, COMPEL CONTROL, and DTV 742 are trademarks of WEGENER Com-munications, Inc. All other trademarks are the property of their respective owners.

Correspondence regarding this publication,

800057-01 Revision CThird Edition: February 2005

should be forwarded to:

Wegener Communications, Inc.Technology Park/Johns Creek11350 Technology CircleDuluth, GA 30097-1502

Phone: 770-814-4000Fax: 770-497-0411

The Wegener DTV 742 is approved under FCC Part 15B Class A, UL 1950, and CSA.

DTV742 User’s Manual

www.wegener.com iii 800057-02 Rev. C

Table of Contents

Chapter 1 General Information1.1 Manual Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.2 DTV742 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.3 DTV742 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.4 Safety Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.5 Glossary of Terms and Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 2 Installation2.1 Unpacking and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Location and Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 DTV 742 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Terminal I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Chapter 3 Operation3.1 Operation Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.2 Ethernet/Web Browser Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Directly Connected PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

LAN Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.3 Web Browser Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Control and Status Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Stream Info Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Unit Configuration Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Config In Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Config Out (1, 2, 3, & 4) Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Q&A/Help Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.4 DTV 742 Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Liquid-Crystal Display(LCD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Push buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Front-Panel LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Rear-panel Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.5 Front-Panel Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Home Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24View Alarms/Warnings Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Clear Errored Seconds Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Input Setup Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Program Status Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27


800057-01 Rev. C iv www.wegener.com

Front Panel Help Timeout Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27IP Setup Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Reset Unit Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Unit Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

3.6 Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Software Code Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Initialization Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Initialization Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

3.7 Transport Stream Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30RF Signal Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Input to Output Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30PSIP Structure and Program Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

3.8 Alarm/Warning System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Alarm Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Warning Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

3.9 Software Upgrades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Items Required for Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Software Preparation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Disconnect the PC from the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Configure the File Transfer Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Set TFTPD32 Settings Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Verify TFTPD32 Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Connect PC to the DTV and Run the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . 34

After the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Chapter 4 Maintenance and Troubleshooting4.1 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

4.2 General Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

No Functions At All . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

4.3 Alarms and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Normal Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

ALARM: All inputs missing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38WARNING: Carrier level out of range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

4.4 Trouble with Browser Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Chapter 5 Customer Service5.1 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

5.2 Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39


www.wegener.com v 800057-02 Rev. C

LIST OF FIGURES

Figure 1.1: DTV 742 8VSB 4-Channel Multiplexer . . . . . . . . . . . . . . . . . . . . . . . . . 2

Figure 2.1: DTV 742 System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Figure 2.2: DTV 742 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Figure 3.1: Control & Status Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 3.2: Stream Info Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Figure 3.3: Unit Configuration Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Figure 3.4: Config In Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 3.5: Config Out 1 Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Figure 3.6: Q&A/Help Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Figure 3.7: DTV 742 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 3.8: Home Screen Example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 3.9: DTV 742 Push Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 3.10: DTV 742 LED Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Figure 3.11: TFTPD32 Top-Level Settings and DHCP Server Tab . . . . . . . . . . . . 32

Figure 3.12: TFTPD32 Settings Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Figure 3.13: Restart TFTPD32 Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Figure 3.14: Tftp Server Tab on TFTPD32 Screen with Progress Bar . . . . . . . . . . 35

LIST OF TABLES

Table 1.1: Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Table 1.2: Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Table 2.1: DTV 742 Connector Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Table 3.1: DTV 742 IP Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Table 3.2: PC IP Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Table 3.3: DTV 742 PID Group (Pidset) Addresses . . . . . . . . . . . . . . . . . . . . . . . 19

Table 3.4: LED Indicator Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23


800057-01 Rev. C vi www.wegener.com

This page intentionally left blank.


www.wegener.com 1 800057-02 Rev. C

Chapter 1 General Information

1.1 Manual OverviewThis manual provides instructions and reference information for the proper installation and operation of the Wegener Model DTV 742 8VSB 4-Channel Multiplexer, referred to throughout the manual as the DTV 742.

Note: User interface details in this manual are based on application software version 104.

The manual is divided into the following chapters:

1 General Information - a description of your DTV 742, its functions and specifica-tions, and a glossary of terms

2 Installation - procedures and information for the correct and safe installation of your DTV 742.

3 Operation - instructions on starting and operating your DTV 742

4 Maintenance and Troubleshooting - information on maintaining your DTV 742 and resolving possible operating difficulties

5 Customer Service - our warranty and information on obtaining help

Please send any suggestions or comments about this manual to [email protected]. If you prefer to post them through the mail, please send your comments to the address below. If you have substantial or complex changes to recommend, our preference is that you copy the page(s) in question, mark your changes on that copy, and fax or mail us the copy. We always appreciate constructive criticism.

Our Address:

Attn: ManualsWegener Communications, Inc.Technology Park / Johns Creek11350 Technology CircleDuluth, GA 30097-1502

Fax Number: (770) 497-0411


800057-01 Rev. C 2 www.wegener.com

1.2 DTV742 OverviewThe DTV 742 8VSB 4-Channel Multiplexer (Figure 1.1) receives VHF/UHF broadcast HDTV signals from four independent inputs and provides four output ASI streams for connection to cable-system QAM modulators or channel groomers. It accepts broadcast or CATV 8VSB or QAM signals on the tuner inputs and produces ASI MPEG transport stream outputs.

Physical Description

The DTV 742 is housed in a standard, rack-mountable chassis. Its front panel provides a user interface through an LCD, eight LEDs, and six push buttons. (See section ). Ports that allow connection to power, incoming signal, and peripheral devices are located on the rear panel.

Figure 1.1: DTV 742 8VSB 4-Channel Multiplexer

Features Your DTV 742 has the following features:

• Four ATSC 8VSB RF input ports (F connector),

• Four ASI MPEG transport stream outputs (BNC connector),

• Lock and tracking of PCR information for all program streams,

• One Ethernet TCP/IP control interface (RJ-45 connector),

• One asynchronous data input/output (DB-9 connector), and

• One expansion slot.

• SNMP control and monitoring

• Storage of ten user-defined configurations



1.3 DTV742 Specifications

Table 1. 1: Technical Specifications

Characteristic Specification

INPUT AC POWER

Voltage 90 to 132 Vac and 175 to 264 Vac auto-detect/selected

Frequency 50/60 Hz ± 2%

Power Consumption <43 Watt

RF

Input Frequency Range 53 to 810 MHz

Symbol Rate 10.76 Msps

Input Data Rate 19.393 Msps

Input Signal Level -80 to -20 dBm

Input Impedance <3.0:1 in 75Ω system

LO Leakage at Input -63 dBm maximum

SERIAL PORT

Standard RS-232

Handshaking None

Service Software download

Baud Rate 115.2 kbps

Formatting 8 data-bits, 1 start, 1 stop-bit, no parity

ETHERNET PORT

Physical Layer 10BaseT/100BaseT (twisted pair) on RJ-45 jack

Media Access and Link Layer Per IEEE 802.3 (Ethernet)

SNMP 2c MIB available (contact Customer Service, see page 49)

ALARM AND WARNING RELAYS

Alarm Function Contact closure for main power off, loss of input signals

Warning Function Contact closure for poor signal quality

Type Form C, NC, NO, and Common available on connector

Rating 30Vdc open circuit, 100 mA max current closed



1.4 Safety SummaryThe DTV 742 is designed for safe use with few special precautions required of the user. The following items are basic precautions to use when installing and working with your DTV 742:

Do not open the DTV 742’s chassis cover.

EXPANSION MODULE SLOT (for future use)

MECHANICAL

Height 1 std. RU (1.75 inches nominal) (44.5 mm)

Width EIA std. 19-inch mounting (482.6 mm)

Depth 13.5 inches (342.9 mm)

Weight 10.3 lb (4.67 kg)

Expansion Module Slots 1 each - 2.5"W x 1.375"H x 7"D on rear panel

ENVIROMENTAL

Use Indoor

Altitude Up to 2000 meters

Temperature Range 0° C to +50° C Operating

-20° C to +70° C Storage

Cooling Internal fan

Relative Humidity (max.) 80% for temperatures up to 31° C decreasing linearly to 50% relative humidity at 40° C.

Table 1. 1: Technical Specifications

Characteristic Specification



1.5 Glossary of Terms and Abbreviations

Table 2: Glossary of Terms

Term Definition

AC Alternating current

Alarm A condition or notification of a condition that prevents your DTV742 from performing properly

Application Software The main host software which sets up the unit hardware, runs the process of acquiring transport stream sources, sets up and monitors the demodulation and multiplexing processes, monitors unit operations, and provides interfaces with the network and local users

ASI (or DVB-ASI) An “asynchronous” bit-serial physical interface for Transport Streams; Transmitting and receiv-ing functions are designed such that the time relationships between all packets and their timing references are unchanged.

ATSC Advanced Television Systems Committee - sets standards for standard definition and high defi-nition television in the U.S. Sometimes used to mean the HDTV standards

Boot loader Software residing in non-writable zone of flash which executes at unit reset

Carrier An RF signal containing coded audio, video, and/or other data

DVB-ASI see ASI

EIA Electronic Industries Association

Ethernet The widely-used LAN technology specified by IEEE standard 802.3

Flash memory A memory dedicated to storing the unit’s software and an image of some hardware programming code

IEEE Institute of Electrical and Electronics Engineers

LAN Local area network; Your DTV742 may be connected to an Ethernet LAN.

LCD Liquid crystal display; The front-panel text screen on your DTV742 is a liquid crystal display.

LED Light-emitting diode; The front-panel indicator lights on your DTV742 are LEDs.

Mbps, kbps Megabits per second or kilobits per second - units of data transport rate

MIB Management Information Base - the database of object definitions

MPEG Moving Picture Experts Group - refers to the method of video compression established by this group

NVRAM Non-volatile memory; this memory is dedicated to storing the unit’s setup parameters. This memory retains its contents through power outages.

PAT Program Allocation Table - master table which identifies all the programs in the transport stream. This table associates Program numbers to the PIDs bearing the associated program’s PMT.

PCR Program Clock Reference - a time-base signal used to synchronize the DTV742's timing to the MPEG encoder for that program. Multiple programs may share a PCR, depending on the multi-plexer used to create the final transport stream.



PID Packet Identifier - the unique transport stream packet identifier assigned to each constituent data stream within the transport stream. Also, in this document, “PID” is used to designate the stream itself.

PMT Program Map Table - table for a given program identifying all the PIDs for its PCR, video, audio, and user data streams

Program In the MPEG hierarchy, a grouping of related audio, video, or generic data PIDs sharing a com-mon PCR time base and (usually) sharing a common schedule (see PMT)

PSI Tables Program-Specific Information Tables - a group of information-bearing tables, each borne by well-known PIDs, regularly transmitted in the transport stream (See also “PAT” and “PMT”. Also, ISO 13818-1 gives a thorough description of these and other tables.)

PSIP Program and System Information Protocol - a method for transporting digital television system information and electronic program guide data

RAM Random access memory - a general term for all memory volatile memory types out of which application software executes and into which its variables, state information, and messages are stored. RAM is also used to designate the volatile storage used by the transport demux and decompression devices.

RF Radio frequency

SNMP Simple Network Management Protocol - A network protocol used to manage TCP/IP networks. This protocol provides functions that enable access to data objects whose definitions are located in the MIB.

TMRA Maximum Recommended Ambient Temperature - the highest operating temperature for which the unit is rated

Transport Stream (or MPEG Transport Stream)

A multiplex of several data streams, each of which is borne in transport packets, 188byte blocks containing a sync word, header information (including a PID), and payload data. This multiplex includes PSI data tables, programs, padding in the form of null packets, and floating PIDs such as those used by COMPEL network control.

Table 2: Glossary of Terms

Term Definition



Chapter 2 Installation

This chapter provides instructions on unpacking, mounting, and connecting your DTV 742 as well as connector information including detailed pinouts.

2.1 Unpacking and InspectionNote: Carefully unpack the unit and its ac power cord and inspect for obvious signs of

physical damage that might have occurred during shipment. Any damage claims must be reported to the carrier immediately. Be sure to check the package contents carefully for important documents and materials.

Note: Please save the packing materials and original shipping containers in case you must later return the unit for repair. Packing these units in other containers in such a way that they are damaged will void your warranty.

2.2 Location and MountingThe DTV 742 should be located indoors and may be mounted in a standard, 19-inch equip-ment rack within one standard RU.

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference for which the user may need to take mitigating action.

DANGER

To avoid damage to the DTV 742 unit and other equipment, or personal injury, the following items should be strictly observed.

Elevated Ambient Operating Temperatures in Rack-Mounted Units

When equipment is installed in a closed or multi-unit rack assembly, the ambient operating temperature of the rack environment may be greater than the room’s ambient temperature. Therefore, consideration should be given to the ambient air temperature within the rack (not just inside the room) when deciding if the maximum recommended ambient operating temperature (TMRA) is met or exceeded.

Reduced Air Flow

Equipment should be installed such that the airflow required for safe operation of the equipment is not compromised. The DTV 742 may be arranged in a rack without empty spaces between units if heat buildup is prevented by ensuring that its side vents remain unblocked and that there is adequate clearance around the vent holes.

Mechanical Loading

Rack-mounted equipment should be installed in such a way that a hazardous condition is not produced by uneven loading. The DTV 742 unit is not very heavy, but total rack loading must be considered. Also, do not rest any unsupported equipment on a rack-mounted DTV 742 unit.



Circuit Overloading

Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits could have on overcurrent protection and supply wir-ing. Ensure that the total rack or breaker power consumption does not exceed the limits of the AC branch circuit. Appropriate consideration of equipment ratings should be used when addressing this concern.

Reliable Earthing

Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (use of power strips, chassis ground lugs, etc.).

Rack Mounting

Your DTV 742 is sized to fit in an EIA-standard, 19-inch-wide equipment rack.

a. First install angle brackets or cross-supports capable of supporting both the unit and its connecting cables. Screw or bolt the supports securely to the equipment rack.

b. Place the DTV 742 on its supports and use four anchor screws or bolts and nuts to secure the unit’s front brackets to the rack.

c. Connect the chassis grounding screw to an earth ground before connecting the power cord to the unit.

WARNING

The front brackets must be secured to the rack. If front brackets are left unsecured, the unit may shift forward and fall from the rack during installation or operation. Failure to secure the front brackets may result in personal injury and/or damage to the equipment.

WARNING

Locate the DTV742 and its cables to avoid impacts, spills, and pulling cables and to ensure sufficient air flow. Failure to locate the DTV 742 in a proper environment may result in damage to the equipment.



2.3 DTV 742 ConnectionsFigure 2.1 shows placement of the DTV 742 in a basic system setup. Multiple RF inputs may be split from a single antenna or separate antennas may be used. Although the figure shows only one antenna connection, each enabled RF input must be connected to an antenna or splitter.

Figure 2.1 : DTV 742 System Setup

Figure 2.2 illustrates details of the DTV 742’s rear panel.

Figure 2.2 : DTV742 Rear Panel

Before applying power, make the following connections to your DTV 742: (Refer to Table 2.1 for connector details.)

a. Connect the chassis grounding screw to an earth ground before connecting the power cord to the unit.

b. Connect the ATSC 8VSB signals from your antenna(s) to the DTV 742's RF IN ports(1, 2, 3, and 4).

c. Connect your downstream equipment to the ASI OUT 1, 2, 3, or 4 ports as desired.

d. Connect your LAN line to the DTV 742’s Ethernet port.

e. If desired, connect the Relays port to your equipment to provide contact closures during alarms and warnings.

f. Finally, connect the supplied ac power cord to the DTV742’s IEC receptacle and to a 90 to 132 Vac source.



Table 2.1: DTV 742 Connector Details

Designation Connector TypePin

NumberSignal Name

115/230 Vac Power Male IEC receptacle AC LINE IN

RF In 1 female F RF IN 1




ASI Out 1 female BNC J4 ASI OUT 1




Ethernet LAN female RJ-45 J7-1

J7-2

J7-3

J7-4

J7-5

J7-6

J7-7

J7-8

EN OUT +

EN OUT -

EN IN +

NC

NC

EN IN -

NC

NC

Terminal female DB-9 J1A-1

J1A-2

J1A-3

J1A-4

J1A-5

J1A-6

J1A-7

J1A-8

J1A-9

DCD (+5V, 4.7 kΩ)

RxD (output)

TxD (input)

NC

GND

DSR (+5V, 4.7 kΩ)

NC

CTS (+5V, 4.7 kΩ)

RI (+5V, 33 Ω)

Relays female DB-9 J1B-1

J1B-2

J1B-3

J1B-4

J1B-5

J1B-6

J1B-7

J1B-8

J1B-9

not used

not used

WARNING COM

ALARM COM

GND

WARNING NO

ALARM NO

WARNING NC

ALARM NC (closes on alarm condition or power failure)



Ethernet An Ethernet 10BaseT/100BaseT port is included and, along with an HTML browser, is the primary user interface. The unit has a URL which is assigned via the front panel. The “home” page can then be accessed via the Ethernet port and an attached computer by entering the unit’s URL (web address) in your browser’s address field. From this page, you can select desired channels and monitor unit status.

SNMP MIB is available. Contact Customer Service (see page 49) for assistance.

Terminal I/O The Terminal serial port is configured to 115.2k, N, 8, 1. The Terminal device is used forfactory testing and debugging of the DTV 742. This I/O is a basic, VT100-like emulation.User input text strings that are terminated in carriage-returns prompt all I/O. The terminalshould be set to local echo ON because the DTV 742 only echoes a carriage-return/line-feed and then a ‘>’ prompt after entry of a command-line terminated by a carriage-return.






Chapter 3 Operation

This chapter contains detailed operating instructions that will guide you in the efficient use of your DTV 742. The following sections address:

• Operation Overview

• Ethernet/Web Browser Setup

• DTV 742 Controls and Indicators

• Front-Panel Operation

• Initialization

• Transport Stream Processing

• Alarm/Warning System

• Software Upgrades

3.1 Operation OverviewThe DTV 742 contains four RF tuners and four multiplexers in a single chassis. Programs from the four tuners are selected for processing. Each ASI output has its own multiplexer which selects programs from any one or all of the tuners. A given program may be included in one or more of the output ASI streams.

The unit is controlled primarily through the Ethernet connector using a web browser. Lim-ited control is available from the front-panel LCD/keypad. All settings may be presumed to be retained through power cycling unless otherwise specified. This means that they are still in effect through resets, whether by power outage, commanded reset, or failure-recov-ery resets.

3.2 Ethernet/Web Browser SetupThe DTV 742’s primary user interface is from a web browser using the rear-panel Ethernet LAN connection. An HTML script interface allows a user to control and monitor the unit using a standard web browser. Each unit contains a user-defined quad URL address, sub-net mask, and gateway address that must be established from the front panel. (See Table 3.2: DTV 742 IP Setup.)

There are two basic methods of using the Ethernet connection:

• With a directly connected PC or

• With a PC connected through a LAN.

Directly Connected PC

For control from a local PC, attach the DTV 742’s Ethernet port to the Ethernet network connector on the PC using a crossover RJ-45 cable (8 pins).

Before using this Ethernet connection, the appropriate IP address, netmask, and gateway must be selected via the front-panel interface.

Perform the DTV 742 IP Setup and PC IP Setup as shown in Table 3.2 and Table 3.3. Addresses other than those listed may be used if they are compatible. Consult your net-work administrator if you have questions.



LAN Connection

For LAN connection, attach the DTV 742’s Ethernet port to the LAN using a normal RJ-45 cable (8 pins). Set the DTV 742 IP Address, Netmask, and Gateway as directed by your net-work administrator. Use any PC on the LAN to connect to the DTV 742 using the web browser instructions below.

Note: Each unit on the network must have a unique address.

3.3 Web Browser ControlGetting Started

To begin monitor and control functions from a PC or LAN connection:

a. Open the current internet browser of your choice from the local PC or computer on the LAN attached to your DTV 742.

b. Set the browser's address field to http://nnn.nnn.nnn.nnn where nnn.nnn.nnn.nnn is the IP address of the unit to be controlled (set from the DTV 742’s front-panel, IP Address screen).

Note: For IP addresses that include subfields with leading zeros, you must omit those zeros when entering the address in your browser. For example, IP address 128.092.050.004 must be entered as 128.92.50.4.

The DTV 742 Control and Status screen will appear. You may also select either the Stream Info, Unit Configuration, Config In, Config Out (1 through 4), or Q&A/Help pages at any time by clicking their respective tabs at the top of the screen. The following paragraphs detail the use of each of these pages:

Control and Status Page

The Control and Status Page (Figure 3.1) provides basic control of the unit and signal sta-tus displays. The left side of the screen is the control side and the right side provides sta-tus of the inputs.

Control

The first item on the Control side is the serial number of the DTV 742 unit and the version number of the installed application software. Below this are the Inputs, Outputs, and Control sections.

Table 3.2: DTV 742 IP Setup

Parameter Setting

IP Address 172.016.100.020

Netmask 255.255.000.000

Gateway 000.000.000.000

Table 3.3: PC IP Setup

Parameter Setting

IP Address 172.016.100.001

Subnet Mask 255.255.000.000



Figure 3.1: Control & Status Page

Under the Inputs heading, you may select the desired RF input video channels for each of the four RF tuners. Select the Broadcast radio button for off-air signals or the CATV radio button for cable television signals. Enter the channel number and click Tune.

Under Outputs, you may set the Output Rate, PSIP presence (Enabled or Disabled), and TSID for each ASI output. The Output Rate may be selected from the drop-down menu as 19.39 Mbps, 26.97 Mbps, 38.81 Mbps, or a custom rate from 2.5 Mbps to 100 Mbps in 1 kbps steps. To set a custom Output Rate, choose Custom (2.5 - 100) from the drop-down menu and enter the desired rate (in Mbps) in the box immediately below the menu.



Finally, under the Control heading, PID Display Mode allows selection of either a Deci-mal or Hexadecimal numbering system for display of the PID addresses on all screens. Time Source is used to select which RF Input to use for the STT signal to be included in the PSIP output of all four multiplexers.

Status

The Status section on the right side of the page provides the status of all input and output signals. The status information is periodically updated automatically. Received signal parameters are labeled RF Input 1 through RF Input 4. These reports include channel selected, frequency, modulation type, frame lock status (true or false), TSID, signal-to-noise ratio (SNR in dB), signal strength quality, and errored seconds. Any active alarms or warnings are displayed in red text beneath the status of the affected RF input.

ASI output information includes the output data rate, the TSID, and the occupied band-width of each of the four ASI outputs (ASI Output 1 through ASI Output 4).

Stream Info Page

The Stream Info page (Figure 3.2) displays complete data on each input and output stream. This page contains information only and does not provide any user control.

The left side lists the program streams contained in each RF input. The first item shown for each input is the short name and the major and minor channel numbers of the signal. Because a transport stream signal may contain more than one program, information on all programs in each RF input is given. The program number and the PID numbers of the PMT and PCR are shown for each program. This is followed by the PID numbers of all video, audio, and data PIDs in the stream. PIDs that are not included in the PMT are listed as "Ghost PIDs".

Note: Channel and program numbers are always shown in decimal notation, while PID numbers are shown either as decimal or hexadecimal depending on your selection on the Control & Status page. Decimal numbers are indicated as 123 while Hexadecimal numbers are indicated as 0x123.

The right side of the page shows the programs contained in each of the ASI output streams.

Acquiring Broadcast ATSC Signals

As with the traditional television broadcast, you will need a good-quality outdoor antenna pointed toward the transmitter. With the antenna correctly positioned and the cable connected to the DTV 742’s RF input, select the channel number on the front panel or via the web interface. Note that this is the ATSC RF channel number (not the broadcaster’s legacy analog channel).

Weak Signal - If you’re within reception range you should see an SNR between 20 dB and 35 dB with no errored seconds. An SNR less than 20 dB with accumulating errored seconds indicates a weak signal condition that results in impaired video and audio. Adjust antenna pointing for maximum signal (higher SNR). If this is not successful, you may need a line amplifier or a higher gain antenna.

Multipath - If you have video problems and the SNR shows wide fluctuations, you may be experiencing multipath reception which is the simultaneous reception of the direct signal plus a strong reflection. Rotating the antenna away from the interfering signal may solve this problem.



Figure 3.2: Stream Info Page

Unit Configuration Page

The Unit Configuration page (Figure 3.3) is used to save and load configurations. A con-figuration is the set of user-selectable items that make up the operating state of the unit. When all user-selectable items have been defined, these setting may be stored as a named configuration. Up to ten configurations may be stored for later use.

Figure 3.3: Unit Configuration Page



The Current Configuration at the top of the page gives the name of the configuration in use. After changing parameters, you may name the new configuration and store it in one of the ten configuration slots.

When a stored configuration is desired for use, select it from the Load Configuration drop-down menu and press the Load button. As soon as the Load button is pressed, the selected configuration is loaded and those settings immediately become the active output characteristics. This feature allows quick changes of multiplex characteristics between predefined settings.

Config In Page

The Config In page (Figure 3.4) is used to select programs from the inputs which will be used in one of the four ASI outputs. The left side of the screen simply presents for easy viewing the information on all programs detected on the four RF inputs. The user may eas-ily view these programs when selecting programs to be included in the multiplexers.

Figure 3.4: Config In Page



The right side of the screen is used for selection of the programs for inclusion in the multi-plexers. There are 32 PID groups available for selection. A PID group is a set of 16 PIDs which are used for all the PIDs associated with the selected program - video, audio, and user data. The PIDs assigned to each PID group are shown in Table 3.4. .

The PMT in a PID group is assigned to the first PID address (e.g., PID group 1, PMT is address 0x020) and is followed by the video, audio, and data PIDs.

Each PID group on the Config In page is followed by two boxes: The first is the Input box, which is used to select which of the four RF inputs will be used for obtaining the input pro-gram. The second (Program) box is used to select the program number to be used from that RF input.

Note: A program from a given RF input may only be placed in one PID group. An attempt to place the same RF input and program number in two PID groups will result in an error message. (Of course, Program 1 of RF Input 1 and Program 1 of RF Input 2 may be selected in two PID groups because they are not the same program.)

After all desired programs have been selected, click Submit to activate your selections.

After the Config In has been established, the output configurations for each of the four ASI outputs may be set up

Table 3.4: DTV 742 PID Group (Pidset) Addresses

PID Group PID Addresses PID Group PID Addresses

1 0x020 to 0x02f 17 0x120 to 0x12f

2 0x030 to 0x03f 18 0x130 to 0x13f

3 0x040 to 0x04f 19 0x140 to 0x14f

4 0x050 to 0x05f 20 0x150 to 0x15f

5 0x060 to 0x06f 21 0x160 to 0x16f

6 0x070 to 0x07f 22 0x170 to 0x17f

7 0x080 to 0x08f 23 0x180 to 0x18f

8 0x090 to 0x09f 24 0x190 to 0x19f

9 0x0a0 to 0x0af 25 0x1a0 to 0x1af

10 0x0b0 to 0x0bf 26 0x1b0 to 0x1bf

11 0x0c0 to 0x0cf 27 0x1c0 to 0x1cf

12 0x0d0 to 0x0df 28 0x1d0 to 0x1df

13 0x0e0 to 0x0ef 29 0x1e0 to 0x1ef

14 0x0f0 to 0x0ff 30 0x1f0 to 0x1ff

15 0x100 to 0x10f 31 0x200 to 0x20f

16 0x110 to 0x11f 32 0x210 to 0x21f



Config Out (1, 2, 3, & 4) Page

Each Config Out page (Figure 3.5) is associated with the ASI output of the same number (Config Out 1 for ASI 1, for example). Instructions given for Config Out 1 apply to the other three Config Out pages as well.

Figure 3.5: Config Out 1 Page



As with the Config In page, the left side of the screen lists all input programs for refer-ence. The right side of the screen is the location for selecting programs to be placed in the multilplexed output.

The first two columns show the RF input and program number for each Pidset (PID group) as set up on the Config In page. The remaining columns are used to configure the output.

The Enabled check box is used to select the programs to be used in the output. In the screen shown in the example above, RF Input 2, Program 3 and RF Input 2, Program 2 have been selected to be included in the output for ASI Output 1.

The Program box is used to renumber the program. if desired or necessary. In the exam-ple, Input Program 3 is changed to Output Program 1 and Input Program 2 is kept as Pro-gram 2.

Note: Even though a program’s number is unchanged, the number must be entered in the Program box.

To the right of the Program box column are Major Channel, Minor Channel, and Name boxes. These allow user selection of these items. The major and minor channel numbers may be selected from 1 to 999 and the name may be up to seven characters in length.

Finally Audio Mapping allows selection of AC-3 Only, MPEG Only, or both AC-3 and MPEG audio PIDs to be included in the output.

After all the desired selections have been made, click the Submit button at the bottom of the page to activate the output.

Set up the Config Out 2, Config Out 3, and Config Out 4 pages for the ASI 2, AS! 3, and ASI 4 outputs in the same manner. When complete, return to the Control & Status page to ver-ify that the outputs appear as desired and that no oversubscription condition exists (more data selected than the output data rate can handle). If there is an oversubscription alarm, you must either increase the data rate for the affected ASI output or remove one or more programs from the output.

Q&A/Help Page

A list of questions and answers about operating your DTV 742 is available on the Q&A/Help page (Figure 3.6). Click the Q&A/Help tab to display this page.

Figure 3.6: Q&A/Help Page



3.4 DTV 742 Controls and IndicatorsThere are three major parts of your DTV 742’s front-panel controls and indicators: the liq-uid-crystal display (LCD), the six push buttons, and the eight LED indicators. Essentially all control available through the terminal is also available through the front panel (Figure 3.7).

Figure 3.7: DTV 742 Front Panel

Liquid-Crystal Display(LCD)

The DTV 742’s 2-line by 20-character LCD indicates unit status and prompts for and reflects user input. Here, you will see the DTV 742’s "Home" screen (the default LCD screen, Figure 3.8) which rotates through data from each of the four RF inputs. The chan-nel number, modulation type (8VSB, 64QAM, or 256QAM), signal-to-noise ratio, and Errored Seconds are displayed for each input.

Figure 3.8: Home Screen Example

No matter which LCD screen is currently displayed, pressing the ESC button repeatedly returns the display to this Home screen. From the Home screen, press the ENT button to display the unit's serial number and the application software version number. Using the adjacent push buttons, you can navigate the DTV 742's various screens and edit its input fields. (See 3.5 Front-Panel Operation on page 24.)

Push buttons The six push buttons (shown in Figure 3.9) are your means of commanding the DTV 742 from the front panel.

Figure 3.9: DTV 742 Push Buttons

The four arrow buttons allow navigation through the menu screens and enable character selection when editing user-input fields. The Enter (ENT) button serves to select menu options (downward navigation), to open user-input fields, or to commit user input to the DTV 742. The Escape (ESC) button allows exit from user-input fields without saving the entry or selection. ESC also provides upward navigation through the menu structure to the home screen. The arrow buttons also provide navigation through user-input screens and switching between user-selectable options.

RF3 CHAN:20 8VSBSNR21.5 ErrSec:0002



Front-Panel LED Indicators

Figure 3.10 below shows the eight light-emitting diodes (LEDs) that provide status informa-tion about the DTV 742 and its processes.

Figure 3.10: DTV 742 LED Indicators

Table 3.4 below describes the meanings of the color and states of each LED.

Table 3.5: LED Indicator Descriptions

IndicatorLabel and Color

Indicator State

Indicator Meaning

RF 1 Constant RF input 1 locked

GREEN Off RF input 1 not locked

RF 2GREEN

Constant RF input 2 locked

Off RF input 2 not locked

RF 3GREEN



RF 4GREEN



WARNING Constant Warning condition(s) exists

YELLOW Off No Warning condition exists

ASI OUTPUT Constant ASI Output is active

GREEN Off ASI Output is inactive

ALARM Constant Alarm condition(s) exists

RED Off No Alarm condition exists

LAN ACTIVITYGREEN

Flash LAN activity present. Only lights when unit receives parameter-change commands. This is not a contin-uous monitor of LAN communications.

Off Not receiving parameter-change commands



Rear-panel Indicators

Two LED indicators on the rear panel give Ethernet status:

ACT – Amber LED: flashes to indicate LAN activity.

LAN – Green LED: ON for 100baseT, OFF for 10baseT.

3.5 Front-Panel OperationThe DTV 742 may be set up and controlled from the front panel as follows:

Note: From any screen, pressing the ESC key repeatedly will return you to the Home screen.

Home Screen The Home screen alternates between the screens shown below (four seconds per screen). The channel number, modulation type (8VSB, 64QAM, or 256QAM), signal-to-noise ratio, and errored seconds are displayed for each input.

For disabled RF inputs (RF 2 in the example below), the Home screen will appear as fol-lows:

Press the ENT key to view the unit's serial number and software version.Press the right arrow key ( ) to go to the View Alarms/Warning screen.Press the key to go to the Reset Unit screen.

Second-level Screen

(A)


(B)


(C)


(D)


RF2 Disabled

S/N: XXXXXXVER: YYY



View Alarms/Warnings Screen

Second-level Screen

Clear Errored Seconds Screen

Input Setup Screen

Where XXXXXX is the unit's six-digit serial number and YYY is the version number of the unit's currently installed application software.

Press the ESC key to return to the Home screen.

View Alarms/Warnings

Press the ENT key to view any active alarms or warnings on the second-level Alarms/Warn-ings Message screen.

Press the key to go to Clear Errored Seconds (if counter is non-zero) or Input Setup.Press the ESC key to go to the Home screen.

Alarms/Warnings Message Screen

No Alarms or Warning

Any active alarms or warnings are described here.

Press the key to view the next alarm or warning (if more than one).Press the ESC key to return to the View Alarms/Warnings screen.

Clear Errored SecsPress<ENT>

This screen only appears if the errored seconds counter is non-zero. Otherwise the next screen, Input Setup is displayed.Press the ENT key to clear the errored seconds counter (for all RF inputs).

Press the key to go to the Input Setup screen.

Press the key to go to View Alarms/Warnings screen.

Press the ESC key to go to the Home screen.

Input Setup...

Press the ENT key to go to the second-level RF Input screens.

Press the key to go to the Program Status screen.

Press the key to go to Clear Errored Seconds screen.Press the ESC key to go to the Home screen.



Second-level screens

Third-level screens

RF Input screen

RF Input 1

Press ENT to go to the three 3rd-level Input Setup screens: Tuner Enable (set to ON or OFF), Channel Number (set number), and RF Standard (set to Cable or Broadcast).Press the key to go to the next RF Input screen.Press the ESC key to return to the Input Setup screen.

Tuner Enable screen

Tuner Enable:ON

Press ENT to enable or disable the RF tuner by selecting ON or OFF with the or key.

Press the key to go to the Channel Number screen.Press the ESC key to return to the second-level Input Setup screen.

Channel Number screen

Channel Number:27

Press ENT to enter the edit mode and change the channel number using the or key.Press the ENT key to confirm your entry or ESC to cancel changes.

Press the key to go to the RF Standard screen.

Press the key to go to Tuner Enable screen.Press the ESC key to return to the second-level Input Setup screen.

RF Standard screen

RF Standard:Broadcast

Press the ENT key and then the or key to select Broadcast or Cable.Press the ENT key to confirm the selection or ESC to cancel changes.

Press the key to go to Channel Number screen.Press the ESC key to return to the second-level Input Setup screen.



Program Status Screen

Second-level Screens

Third-level Screens

Front Panel Help Timeout Screen

After a period of inactivity, some information on the LCD is replaced with help information on how to use the front-panel controls. This timeout period (elapsed time between the last front-panel activitiy and presentation of help information) may be changed using the Front Panel Help Timeout screen. For users familiar with front-panel operation, selecting No Tim-eout will prevent the help information from appearing. Other users may wish to set the tim-eout period from 3 to 60 seconds.

Program Status...

Press the ENT key to view the second-level program status screens.

Press the key to go to Panel Help Timeout.

Press the key to go to Program Setup.

Press the ESC key to go to the Home Screen.

Program Status screen

Input Number:1

Press the ENT key to view the third-level Program Status screen for this Input (1).

Press the key to go to the next input (2, 3, and 4).Press the ESC key to return to the Program Status screen.

Program Status screen

ProgIn XXXXX AAAAAAAOut:Y BBBBBBB

where XXXXX is the Input Program Number, AAAAAAA is the Service Descriptor (name) for the program, Y is the ASI Output Port(s), and BBBBBBB is the available audio on the input for the program (AC-3, MPEG, or MPG/AC3).

Press the key to see the status of any other programs from this input.Press the ESC key to return to the 2nd-level Program Status screen.

Panel Help Timeout10

Press the ENT key and then the or key to select the front-panel help message timeout. Values of 3, 5, 10, 30, or 60 seconds, or No Timeout may be selected.Press the ENT key to confirm the selection or ESC to cancel changes.

Press the key to go to the IP Setup screen.

Press the key to return to the Program Status screen.Press the ESC key to return to the Home screen.



IP Setup Screen

Second-level Screens

IP Setup...Select? Press<ENT>

Press the ENT key to go to the IP Address screen.

Press the key to go to the Reset Unit screen.

Press the key to return to the Front Panel Timeout screen.Press the ESC key to return to the Home screen.

IP Address Selection screen

IP Address:0.0.0.0

The current IP address is displayed.Press the ENT key and then use the arrow keys to change the IP address. Press the ENT key again to confirm the selection or ESC to cancel changes.

Press the key to go to the Netmask Selection screen.Press the ESC key to return to the IP Setup screen.

Netmask Selection screen

Netmask:255.255.0.0

The current netmask is displayed. The netmask is combined with the IP address to produce the network and unit address on the LAN.Press the ENT key and then use the arrow keys to change the netmask.Press the ENT key again to confirm the selection or ESC to cancel changes.

Press the key to go to the Gateway Selection screen.

Press the key to return to the IP Address screen.Press the ESC key to return the IP Setup screen.

Gateway Selection screen

Gateway:0.0.0.0

The current gateway address is displayed. This is the address the unit uses to connect to the Internet. If no Internet connection is desired, set the gateway address to 0.0.0.0.Press the ENT key and then press the arrow keys to change the gateway address. Press the ENT key to confirm the selection or ESC to cancel changes.

Press the key to retrun to the Netmask screen.Press the ESC key to return the IP Setup screen



Reset Unit Screen

Use this screen to reset the unit or to enter program upgrades. (See 3.9 Software Upgrades on page 31 for details on upgrading the application software.

If ENT is pressed at this time, the following screens appear:

Unit Shutdown

Simply remove power to the unit to shut down your DTV 742. No special procedure is required.

3.6 InitializationSoftware Code Structure

The DTV 742 Multiplexer contains the following unit software: A boot loader and one ver-sion of operating application software. Before power-up, these components are stored in non-volatile memory. The boot loader resides in a portion of the memory that may only be written at the factory while the application is stored in a portion of memory that can be over-written with down-loads of new software. The boot code has the responsibility of deciding if the resident application software image should be allowed to execute.

Initialization Sequence

At power up, the boot loader software executes first. It performs a test of RAM and then relocates itself for further execution from there. (See 3.9 Software Upgrades on page 31 for instructions on putting the DTV 742 into serial command mode.) During boot-up, the follow-ing screens appear in sequence on the LCD:

Reset Unit...

Press the ENT key to reset the unit and start the boot loader.

Press the key to return to the IP Setup screen.

Press the ESC key or to go to the Home Screen.

Command SuccessfulUnit Booting...

Hit Key to stop BootBooting in 3

Allow the unit to boot or press the key to stop the boot process for a software upgrade (3.9 Software Upgrades on page 31) and the following screen appears:

Press ENT to UpgradePress ESC to QUIT

Press ENT to enable a TFTP through Ethernet software upgrade.Press ESC to quit and continue booting.

FPCon v001 All front-panel LEDs light are OFF during the boot process.

Hit key to stop boot Booting in 2



Following normal boot-up, the "Home" screen will appear as described in section 3.5 Front-Panel Operation on page 24 and the LEDs will reflect the actual state of the unit.

Initialization Failure

When in Initialization Failure mode, the unit is essentially dead. There is no ASI output, the alarm relay is de-energized (alarm state), the ALARM LED is ON, the general-purpose relays are all open, and the unit does not attempt acquisition of input streams. If repeated power-up sequencing continues to indicate an initialization failure, call Wegener Customer Service for assistance.

3.7 Transport Stream ProcessingRefer to ISO 13818-1 for supporting details on the structure of MPEG Transport Streams.

RF Signal Reception

The channel number or carrier frequency must be supplied to the tuner in order for the DTV 742 unit to derive its Transport Stream from the RF input. This data is used to set up the tuner module. If carrier acquisition is successful, then the Transport Stream borne in the carrier will be passed to the ASI output.

Input to Output Processing

The DTV 742 has four RF ATSC inputs that the unit processes. Programs are passed through to the selected ASI output. A program or programs from one RF input may be routed to one or more ASI outputs. Each ASI output may receive signals from all RF inputs. However, an ASI output may also be set up to receive signals from only one RF input.

PSIP Structure and Program Selection

Within the transport stream are PIDs carrying tabular information on that stream. The PAT describes all the programs available. A program number identifies each program in the transport stream. When a source of data is acquired, the stream is passed to the internal transport demultiplexer. This circuit then extracts the PAT and PMT information and pro-vides this information to the user on the web interface.

3.8 Alarm/Warning SystemThe alarm and warning system is intended to provide indications to the local user of a crit-ical failure or imminent failure. See Table 3.5: LED Indicator Descriptions on page 23 for the visual indications.

Alarm Conditions

Generally, if the unit is unable (or presumed to be unable) to present output from a trans-port stream, then that is an alarm state. The following list defines all alarms during normal operation: (Also see Initialization Failure on page 30.)

1. All inputs missing - no RF input signal detected.

2. RF missing - no RF signal at one or more enabled inputs.

3. RF n PAT missing - PAT missing in a specific RF input stream (RF input port n).

Booting System...Bootloader Ver 103

Done BootingBootloader Ver 103



Warning Conditions

The DTV 742 presents the following warnings when an input transport stream is missing needed information.

1. PCR missing – An input transport stream does not include a PCR (program clock ref-erence).

2. PMT missing - An input transport stream does not include a PMT (program map table).

3.9 Software UpgradesYou may upload application software upgrades to the DTV 742 in the field using the Ether-net port.

Once the upgrade starts, the DTV 742 unit will not be processing the signals so it is best to take the unit off line while downloading the new software. From start to finish, the upgrade and re-booting of the unit should last about 1½ minutes, once everything is configured cor-rectly.

Items Required for Upgrade

To perform the upgrade, you will need the following:

• A PC (computer)

• A LAN Crossover Cable (RJ-45)

• The TFTPD32 FTP Server program,

• A utility program to un-zip the TFTPD32 program

• The DTV upgrade software.

Software Preparation Procedure

To obtain the upgrade software and prepare it for installation, do the following:

1. Create a new directory (folder) on your hard drive and name it DTV Software.

2. Use your internet browser to go to http://www.wegener.com/custservdownload.html .

3. Locate the latest upgrade file for the DTV 742 (with a filename like dtv742-xxx.cf), then download and save it in the DTV Software folder.

4. With your browser go to http://www.tftpd32.jounin.net/ .

5. Download the free FTP shareware program named TFTPD32.zip and save it in the DTV Software folder with the DTV 742 software upgrade file.

6. Use your Unzip utility to extract the TFTPD32.exe file from the TFTPD32.zip file that you downoladed.

Disconnect the PC from the Network

If the computer to be used on for the upgrade is on a network, we recommend that you disconnect the Network cable from the computer and restart the computer before connect-ing the PC to the DTV 742 unit to be upgraded. The upgrade may not start up correctly if you don’t reset the computer.



Configure the File Transfer Program

To set up the TFTPD32 file transfer program for upgrading the DTV 742 software, do the fol-lowing:

1. Start the TFTPD32.exe program on the PC (by double-clicking it in the directory, or use Run on the Start menu). Figure 3.11 below shows the top-level TFTPD32 window that displays when the program opens.

Figure 3.11: TFTPD32 Top-Level Settings and DHCP Server Tab

2. Set the Current Directory field to specify the file you created on the PC hard drive to hold the upgrade software: C:\DTVSoftware.

3. The Server interfaces field should display the PC’s IP Address. (The TFTPD32 program will automatically set this option equal too your computers IP address.)

4. On the DHCP server tab, set the IP pool starting address to the IP Address of the DTV 742 unit being updated.

5. Set the Size of pool field to 100.

6. In the Boot File field, enter the name of the DTV 742 software upgrade file that you downloaded: DTV742-xxx.cf.

Note: The xxx part of the DTV742-xxx.cf filename must match the upgrade file’s revision number.

7. Set (leave) the WINS/DNS Server address as 0.0.0.0.

8. Set (leave) the Default router address as 0.0.0.0.

Your PC’s IP address

IP address of DTV unit

DTV Software upgrade



9. The Mask address should match the first two sets of numbers of the DTV 742’s IP Address, followed by .0.0. For example, if the DTV IP address = 172.16.90.150, than set the Mask to 172.16.0.0.

10. Click the Save button in the middle of the screen to save these entries.

Set TFTPD32 Settings Options

Additional options must be set on TFTPD32 Settings screen:

1. Click the Settings button at the bottom center of the TFTPD32 screen to display the TFTPD32 Settings screen shown in Figure 3.12 below.

Figure 3.12: TFTPD32 Settings Screen

2. Under Global Settings, click the check boxes to select TFPT Server, Syslog Server, snd DHCP Server. (Leave the others blank.)

3. Under TFTP Security, click and select Standard.

4. Under Advanced TFTP Options, click Option negotiation and Show Progress bar.

5. Click the OK button at the bottom the screen when yo are finished.

6. The TFTPD32 dialog box shown in Figure 3-13 requires that you restart the Program to apply the new settings.



Figure 3.13: Restart TFTPD32 Dialog Box

7. Click the TFTPD32 button to restart the TFTPD32 program.

Verify TFTPD32 Settings

When the TFTPD32 program window reopens, verify that the Current Directory field dis-plays the file containing the DTV 742 upgrade software.

Connect PC to the DTV and Run the Upgrade

You are now ready to connect the PC to the DTV 742 and perform the software upgrade:

1. Connect the PC directly to the DTV 742 using an RJ-45 Ethernet crossover cable.

Note: Do not connect the DTV 742 to the PC over your network.

2. When you power up the DTV 742, the Front-panel LCD screen will display a message

that says Hit any key to stop boot. Press the or button to enter the upgrade mode,

Note: This screen is set to time out after 2 seconds; you have to be ready to push the button and stop the boot process..

3. After you interrupt the boot process, the LCD screen displays the the two lines: Press ENT to upgrade and Press ESC to quit. Press the ENT button to start the upgrade trans-fer, which will start immediately and only take about 3 seconds.

Note: If unit is powered-up and booting because you did not interrupt it fast enough, go to the Reset Unit menu, and press ENT to reset the unit, then immediately press

and hold the or button, then press ENT again to enter the upgrade mode as soon as the Press ENT to upgrade message appears.

4. Watch the progress of file transfer by selecting the Tftp server tab on the TFTPD32 screen, as shown in Figure 3.14.



Figure 3.14: Tftp Server Tab on TFTPD32 Screen with Progress Bar

After the Upgrade

The DTV 742 will automatically restart when the upgrade file transfer is completed and writ-ten to flash. After unit resets, verify that the correct code has been loaded by pressing the ENT button to view the unit's serial number and software version on the LCD screen,mak-ing sure that the version number matches the xxx in the DTV742-xxx.cf upgrade file.

Note: We recommend that once all the DTV 742 units have been upgraded, all the files and the folder used for this upgrade be deleted from your hard drive.

Progress bar showing file transfer.Note, it will only be on the screenfor about 3 seconds.






Chapter 4 Maintenance and Troubleshooting

4.1 MaintenanceMaintenance of the DTV 742 is limited to keeping the chassis clean and ensuring that cables remain firmly connected. Occasionally wipe the exterior with a soft, damp cloth to remove any accumulated dust and dirt and check that cables are securely attached.

The DTV 742 incorporates security labels over some of the screws. There are no user-ser-viceable components within the DTV 742. Tampering with the security labels or opening the unit will void your warranty. If you have any questions, contact Wegener’s Customer Ser-vice Department at the address or numbers listed under Customer Service.

4.2 General TroubleshootingThis section is not an intended as an exhaustive list of all possible situations. Please con-tact us as directed in Chapter 5 Customer Service on page 39, with any problems you can-not resolve independently.

If you are experiencing any difficulties, first check the LCD and LED indicators on the DTV 742 to determine if any warnings or alarms are active. See Table 3.5: LED Indicator Descriptions on page 23 for descriptions of LED states. If operating over the Ethernet interface, check the Control and Status tab on your browser for Warning messages.

No Functions At All

If the unit is not functioning at all and neither the LCD nor any LEDs are active, there may be a loss of ac power. Do the following:

a. Check that ac power cord is firmly connected at both ends.

b. Check that your ac power source is supplying ac power.

4.3 Alarms and Warnings

In the following sections, LEDs are illustrated as black (off) or white (on) to represent actual LED appearance.

Alarms and warnings may also be viewed on the front-panel LCD and through the web interface. (See sections 3.3 Web Browser Control and 3.5 Front-Panel Operation in Chapter 3 of this manual).



Normal Operation

RF Input and ASI Output Locked - The LEDs are shown here reflecting the DTV 742 in normal operation with no Alarms (more than one RF input may be locked at a given time):

ALARM: All inputs missing

Video is lost when incoming signal is lost. The ALARM LED lights if all RF inputs are miss-ing. When no RF LEDs are active (unlit as shown below), all RF input has been lost. Check the antenna and RF input connections.

WARNING: Carrier level out of range

Video may be garbled or lost when the RF carrier level is out of range. If the carrier level is too high or too low, the WARNING LED will be lit and the affected channel’s RF indicator will be off. In the illustration below, the carrier level is out of range on RF1, but the remain-ing RF inputs and ASI output are unaffected. Some means of amplifying or attenuating the signal should be attempted to bring the carrier level into range.

4.4 Trouble with Browser InterfaceIf the unit appears to be functioning normally with no alarm or warning conditions, but you cannot use the web browser interface, first check the LED on the rear panel next to the Ethernet connector. It will illuminate and blink as LAN data are detected. If this LED is Off, check the cabling to the LAN. If the LED remains off after verifying the LAN connection, contact Customer Service. If the Ethernet LED is illuminated, verify that you are using the correct IP address. (See Ethernet/Web Browser Setup on page 13.)

If the address is correct, but the interface still does not function, check your computer’s IP settings and consult your network administrator for additional help.



Chapter 5 Customer Service

5.1 WarrantyThe following warranty applies to all Wegener Communications products including the DTV 742 8VSB 4-Channel Multiplexer:

All Wegener Communications products are warranted against defective materials and workmanship for a period of one year after shipment to customer. Wegener Communications' obligation under this warranty is limited to repairing or, at Wegener Communications' option, replacing parts, subassemblies, or entire assemblies. Wegener Communications shall not be liable for any special, indirect, or consequential damages. This warranty does not cover parts or equipment which have been subject to misuse, negligence, or accident by the customer during use. All shipping costs for warranty repairs will be prepaid by the customer. There are no other warranties, express or implied, except as stated herein.

5.2 Technical SupportIn the event that the unit should fail to perform as described, or if you need help resolving problems with your DTV 742, contact:

Wegener Communications Customer Service

Phone: (770) 814-4057

FAX: (678) 624-0294, or

E-mail: [email protected].

To return a product for service:

a. Obtain a Return Material Authorization (RMA) number by completing and faxing a copy of the RMA Request Form to (678) 624-0294. You may E-mail the same information instead to: [email protected]

b. To help us identify and control returned units, plainly write the RMA number on the outside of the product-shipping container. This will help us return your unit to you as quickly as possible.

c. Return the product, freight prepaid, to the address below:

Service Department RMA# ________Wegener Communications, Inc.359 Curie DriveAlpharetta, GA 30005

Note: All returned material must be shipped freight prepaid. C.O.D. shipments will not be accepted.

Please contact Customer Service at the number above if you have any questions about obtaining service for your DTV 742.




Documents

DTV 742 - WEGENER · 2006-11-29 · DTV 742 User’s Manual 800057-01 Rev. C 2 1.2 DTV742 Overview The DTV 742 8VSB 4-Channel Multiplexer (Figure1.1) receives VHF/UHF broadcast HDTV