Upload
rahulkumarsingh
View
223
Download
1
Embed Size (px)
Citation preview
7/25/2019 Dynamic behavior of pile foundations under cyclic loading in liquefiable soils.pdf
1/13
Dynamic behavior of pile foundations under cyclic loading in liquefiable soils
Amin Rahmani , Ali Pak
Department of Civil Engineering, Sharif University of Technology, P.O. Box 11155-9313, Tehran, Iran
a r t i c l e i n f o
Article history:
Received 5 March 2011
Received in revised form 12 September
2011Accepted 13 September 2011
Available online 11 November 2011
Keywords:
Liquefaction
Pile foundations
Fully coupled three-dimensional dynamic
analysis
Dynamic behavior of pile
a b s t r a c t
In this paper, a fully coupled three-dimensional dynamic analysis is carried out to investigate the
dynamic behavior of pile foundations in liquefied ground. A critical state bounding surface plasticity
model is used to model soil skeleton, while a fully coupled (uP) formulation is employed to analyze soildisplacements and pore water pressures. Furthermore, in this study, variation of permeability coefficient
during liquefaction is taken into account; the permeability coefficient is related to excess pore water
pressure ratio. Results of a centrifuge test on pile foundations are used to demonstrate the capability
of the model for reliable analysis of piles under dynamic loading. Then, the verified model is used for a
parametric study. The parametric study is carried out by varying pile length, frequency of input motion,
fixity of the pile head, thickness of the liquefying soil layer and relative density of liquefying soil layer.
Three different soil profiles have been considered in this study. In general, parametric studies demon-
strate that fixity of the pile head, thickness of liquefying soil layer and frequency of input motion are
the most critical parameters which considerably affect piles performance in liquefied grounds.
Crown Copyright 2011 Published by Elsevier Ltd. All rights reserved.
1. Introduction
The behavior of pile foundations under earthquake loading is an
important issue that widely affects the performance of structures.
Design procedures have been developed for evaluating pile behav-
ior under earthquake loading; however, application of these proce-
dures to cases involving liquefiable ground is uncertain since the
performance of piles in liquefied soil layers is much more complex
than that of non-liquefying soil layer not only because the super-
structure and the surrounding soil exert different dynamic loads
on pile, but also because the stiffness and shear strength of the sur-
rounding soil diminishes over time due to non-linear behavior of
soil and also pore water pressure generation.
Liquefaction represents one of the biggest contributors to dam-
age of constructed facilities during earthquakes[1]. This phenom-
enon was reported as the main cause of damage to pilefoundations during the major earthquakes such as Alaska, 1964,
Loma-Prieta, 1989, Hyogoken-Nambu, 1995 [1]. Prediction of
seismic response of pile foundations in liquefying soil layers is
difficult, and there are many uncertainties in the mechanisms in-
volved in soilpile-superstructure interaction. However, in recent
decades, a wide range of centrifuge and shaking table tests and
also various numerical methods have been employed in order to
provide better insights into the dynamic behavior of pile founda-
tions in liquefiable soils. These researches can be divided into
three categories: field observations, laboratory tests, and numeri-
cal modeling.
1.1. Field observations
These studies mainly investigate the distribution of the failure
patterns, settlement and lateral displacement of piles. During
Niigata Earthquake, 1964, many pile foundations failed to support
structures due to the liquefaction of the surrounding soil. Accord-
ing to Hamada[2], the ground in the vicinity of a four-storey build-
ing moved approximately 1.1 m, and the maximum lateral
displacement of concrete piles with a diameter of 35 cm and length
of 69 m was around 70 cm. The large amount of lateral displace-
ment caused severe damage to the pile at the interface of the liq-
uefied and non-liquefied layers. Mori et al. [3] conducted an
excavation survey and internal inspection of the damaged pilesof a silo which suffered severe damage due to the Hokkaido Nan-
sei-Oki Earthquake, 1993. They concluded that damage usually oc-
curs at three different locations: at the pile head (for fixed-head
piles), at a depth of 13 m below the pile cap (for free-head piles)
and at the interface of the liquefied and non-liquefied layers. This
observation has been confirmed by others such as Tachikawa
et al.[4], Shamoto et al.[5], and Onishi et al.[6].
1.2. Laboratory tests
These studies include some dynamic centrifuge tests and
also shaking table tests of pile-supported structures in which
0266-352X/$ - see front matter Crown Copyright 2011 Published by Elsevier Ltd. All rights reserved.doi:10.1016/j.compgeo.2011.09.002
Corresponding author. Tel.: +98 21 6616 4225; fax: +98 21 6601 4828.
E-mail address:[email protected](A. Rahmani).
Computers and Geotechnics 40 (2012) 114126
Contents lists available at SciVerse ScienceDirect
Computers and Geotechnics
j o u r n a l h o m e p a g e : w w w . e l s e v i e r . c o m / l o c a t e / c o m p g e o
http://dx.doi.org/10.1016/j.compgeo.2011.09.002mailto:[email protected]://dx.doi.org/10.1016/j.compgeo.2011.09.002http://www.sciencedirect.com/science/journal/0266352Xhttp://www.elsevier.com/locate/compgeohttp://www.elsevier.com/locate/compgeohttp://www.sciencedirect.com/science/journal/0266352Xhttp://dx.doi.org/10.1016/j.compgeo.2011.09.002mailto:[email protected]://dx.doi.org/10.1016/j.compgeo.2011.09.0027/25/2019 Dynamic behavior of pile foundations under cyclic loading in liquefiable soils.pdf
2/13
seismic response of pile, soil and superstructure are investigated.
Wilson et al. [7]conducted a series of centrifuge tests on single
piles and pile groups located in liquefiable soils in order to ob-
serve the py behavior of piles embedded in liquefying sands.
The centrifuge tests results indicated that py curves were
highly time-dependent in liquefiable soils; lateral resistance on
the pile decreased by increasing pore water pressure, and there
was very little lateral resistance on the pile even under largerelative displacements. Furthermore, Yao et al. [8] used large
shaking table tests and concluded that the transient state prior
to soil liquefaction was important in the design of piles because
dynamic earth pressure showed peak response in this state.
Other researchers such as Abdoun and Dobry [9], Suzuki et al.
[10], Dungca et al. [11], Bhattacharya et al. [12], Tamura and
Tokimatsu [13] and Han et al. [14] also investigated dynamic
behavior of pile foundations in liquefiable soils using shaking
table tests.
1.3. Numerical modeling
The effectiveness of numerical simulation tools for analyzing
liquefaction problems have become more important and promi-
nent in the light of potential disadvantages of physical models
used in experimental simulation[15]. Since two and three dimen-
sional numerical modeling are computationally complex and
time-consuming, most of the researchers and designers prefer to
use one-dimensional Winkler method based on finite element or
finite difference methods for the seismic analysis of pile founda-
tions. Kagawa [16], Yao and Negami [17], Fujii et al. [18], and
Liyanapathriana and Poulos [19] developed this method so that
liquefaction of surrounding soil was taken into account during
analyzing process. Miwa et al. [20], Liyanapathirana and Poulos
[19,21], and Chang et al.[22]showed that one-dimensional meth-
od is approximately capable of predicting maximum lateral dis-
placement and maximum bending moment of pile foundations
in liquefied soils; however, it is obvious that Winkler modelsare not able to simulate the prototype model accurately because
it is difficult to estimate the accurate values for the springs and
dashpots coefficients which considerably change over time. Finn
and Fujita [23], Klar et al. [24], Oka et al. [25], Uzuoka et al.
[26], Cheng and Jeremic [15] Comodromos et al. [27] used
three-dimensional finite element method in order to simulate
piles in liquefying soil layers. Each of these models possesses
varying prediction accuracy and certainty. In some of these papers
fully-coupled formulation (uP or uPU formulation) has been
employed; while in others the uncoupled formulation, in which
soil skeleton displacements and pore water pressure generation
are computed separately, has been used. According to the studies,
three-dimensional models are able to simulate most of the phe-
nomena which have been observed in the field more accuratelythan that of one-dimensional models.
In general, considering previous studies on the performance of
pile foundations embedded in liquefiable grounds, one may come
to the conclusion that there is a significant lack of understanding
in involved mechanisms. Besides, it should be noted that in the
previous studies the variation of soil permeability during liquefac-
tion has not been considered in the modeling. However, it is com-
monly demonstrated that soil permeability considerably changes
during liquefaction. Therefore, in the present study, it is intended
to take permeability variation into account in the soilpile-super-
structure simulation. The work presented in this paper utilizes a
fully coupled three-dimensional dynamic analysis together with
a well-calibrated constitutive model and a verified numerical
methodology in order to simulate the behavior of piles embeddedin liquefiable soils more accurately.
2. Numerical formulation
In this study, auPfully coupled formulation, presented by Zie-
nkiewicz and Shiomi[28], is used for modeling of soil skeleton and
pore fluid. TheuPformulation captures the movements of the soil
skeleton (u) and the change of the pore pressure (P). This formula-
tion is applicable for dynamic problems in which high-frequency
oscillations are not important, such as soil deposit under earth-quake loading. Using the finite element method for spatial discret-
ization, theuPformulation is as follows[29]:
MU
ZV
BTr0dV QP fs
0 1
QT _U HP S _P fp
0 2
whereMis the mass matrix, Uis the solid displacement vector, B is
the straindisplacement matrix, r0 is the effective stress tensor, Q
indicates the discrete gradient operator coupling the motion and
flow equations, Pis the pore pressure vector, S is the compressibil-
ity matrix, andH is the permeability matrix. The vectors f(s) andf(p)
include the effects of body forces, external loads and fluid fluxes.
Numerical integration of the above-mentioned equations isdone using Newmark algorithm, and implementation of these pro-
cedures was performed using OpenSees[30]framework, which is
an object-oriented program for finite element analysis. The Open
System for Earthquake Engineering Simulation (OpenSees) is a
comprehensive and continually developing software that is used
in the simulation of seismic response of structural and geotechni-
cal systems. In this study, a number of elements and material mod-
els from UCD computational geomechanics toolset, available in this
software, are employed. The employed elements and material
models are discussed in the following sections.
3. Constitutive modeling of sand behavior
Material model is one of the most important parts of numericalsimulation of the dynamic behavior of liquefiable soils. Using a
comprehensive constitutive model which possesses the simulative
ability to model the behavior of drained or undrained saturated
sands under monotonic and cyclic loadings leads to accurate mod-
eling of problems where liquefaction is involved. Accordingly, in
this research a critical state two-surface plasticity model devel-
oped by Dafalias and Manzari[31]is used. The most striking fea-
ture of this model is its capability to utilize a single set of
material parameters for a wide range of void ratios and initial
stress states for the same soil. It should be noted that initial stress
states, void ratio and fabric evolve through all stages of loading
(see Ref.[29]for more details about the employed material model).
This model possesses 15 parameters divided into 6 categories
based on their functions. These parameters are calibrated for Neva-da sand by Shahir[32,33]using tests performed by Earth Technol-
ogy Corporation in the course of the VELACS project [34].The
calibrated parameters are listed inTable 1.
4. Variation of soil permeability during liquefaction
Many studies have demonstrated that permeability coefficient
significantly increases during liquefaction phenomenon due to
structural change in soil skeleton. At the onset of liquefaction, soil
particles lose full contact with each other, and this change creates
additional pathways for water. The creation of such new, larger
flow pathways reduces the pore shape factor and tortuosity
parameters, and consequently leads to a significant increase in per-
meability coefficient[32]. The amount of increase in permeabilitycoefficient during liquefaction has been reported in some
A. Rahmani, A. Pak / Computers and Geotechnics 40 (2012) 114126 115
7/25/2019 Dynamic behavior of pile foundations under cyclic loading in liquefiable soils.pdf
3/13
investigations. Arulanandan and Sybico [35], based on the mea-
surement of changes in the electrical resistance of saturated sand
deposit during liquefaction in the centrifuge tests, concluded that
in-flight permeability of saturated sand during liquefaction in-
creases up to 67 times greater than its initial value. Jafarzadeh
and Yanagisawa [36] by measurement of the volume of the ex-
pelled water from saturated sand columns in shaking table model
tests indicated that the average permeability coefficient during
excitation is 56 times greater than its static value. Manzari and
Arulanandan [37] used variable permeability in their numerical
simulation. In their study, predictions of excess pore pressure
and settlement were satisfactory, but lateral displacements were
not simulated reasonably well. Balakrishnan[38]employed a fac-
tor of 10 for increasing the permeability coefficient in numerical
model in order to adjust the results of the simulation with the cen-
trifuge test measurements for the soil settlement during liquefac-
tion. Also, according to Taiebat et al. [39] and Shahir and Pak
[40]using a constant value of permeability coefficient in numericalanalysis results in a much smaller value of soil settlement
compared to the measured value. Shahir and Pak[40]concluded
that incorporation of permeability variation in the numerical
model is necessary for capturing both pore pressure and settle-
ment responses of a liquefiable soil mass.
Therefore, in this study, variation of permeability coefficient has
been considered in numerical modeling of liquefiable layers using
a formulation suggested by Shahir and Pak[40]in which a direct
relationship between the permeability coefficient and excess pore
water pressure ratio (ru) was proposed. This relationship is as
follows:
kpki
1 a 1rb1u During PWP build up phaseru < 1
kpli
a During liquefied stateru 1
kpki
1 a 1rb2u During consolidation phaseru < 1
3
wherekiis initial permeability coefficient,kbis permeability coeffi-
cient during excitation,ruis defined as the ratio of the difference of
current pore pressure and hydrostatic pore pressure over the initial
effective vertical stress (ru Du=r0v0).a;b1; b2 are positive materialconstant. These parameters are 20, 1.0 and 8.9, respectively for Ne-
vada Sand[40]. This basically means that the permeability coeffi-
cient increases up to 20 times during the initial liquefaction. It is
to be noted that the proposed value fora is consistent with the re-ported value by Balakrishnan[38]because the peak value of 20 is
nearly equivalent with average value of 10. Validity and efficiency
of the proposed formulation can be found in Refs.[33]and [40].
5. Pilesoil model development
In this research, soil layers are modeled by cubic eight-node
elements with uP formulation (called EightNodeBrick_u_p ele-
ment in OpenSees framework) in which each node has four de-
grees of freedom: three for soil skeleton displacements and one
for pore water pressure. Pile is modeled by beam-column ele-
ments which have six degrees of freedom for each node: threefor displacements and three for rotations. A lumped mass on the
pile head represents the superstructure. The finite element mesh
is presented inFig. 1.
One of the important and difficult steps in numerical simulation
of pile foundations in the soil media is the connection of pile ele-
ments to the surrounding soil elements. In the present work, the
connection is provided by means of rigid beam-column elements
which possess the same physical properties of pile elements. As
shown in Fig. 2, these elements connect each pile node to sur-
rounding nodes of soil elements at an equal depth. At the connec-
tion point, soil element nodes slaved to the connection element
node for three translational DOFs, while the three rotational DOFs
of the connection element are left unconnected. Furthermore, slip-
page between pile elements and surrounding soil elements is fea-
sible in all directions by using zero-length interface elements,
which are defined by two nodes at the same location where the
connection beam-column element is connected to the surrounding
soil (as shown inFig. 2). An elastic-perfectly plastic material model
is used for the interface elements. Some static field tests and also a
centrifuge test, discussed later in this paper, were simulated in or-
der to obtain suitable mechanical properties of the interface ele-
ment. Based on these studies, Youngs modulus and yielding
strain of this material are selected to be 2000 kPa and 0.04, respec-
tively and are used throughout the main simulations of pile behav-
ior in liquefiable soil layer. It is to be noted that values considered
for these parameters lead to immediate yielding of interface ele-
ment i.e. slippage at soilpile interface can take place.
However, further studies and simulations revealed that the ef-
fect of interface elements was not that significant for the centrifugetest that has been simulated in this study. Comparing the numer-
ical results of the model with and without employing interface ele-
ments revealed a maximum difference of 5%. This can be specific to
the kind of the problem that is studied in this research where the
saturated liquefiable ground is horizontal and the soil is cohesion-
less. Nevertheless, the above mentioned interface element proper-
ties were employed to improve the quality of simulations and
match the numerical results with the experimental values as much
as possible.
Due to the symmetry of the model, the model is halved at the
line of symmetry along the center-line of the pile, and all applied
static loads are halved. Soil elements are coarser far from the pile
and finer around the pile (seeFig. 1).
Boundary conditions are set in the following way:
Base of the mesh is fully fixed in all directions.
At the side planes, parallel to the excitation direction, nodes are
restrained from movement in they direction, and at the ones,
perpendicular to the excitation direction, the nodes at equal
depths are constrained to have equal displacements in the x
direction to simulate free-field ground motion.
All other internal nodes are free to move in any direction.
Pore water pressures are free to develop for all nodes except the
ones at the level corresponding to the ground water table
elevation.
Simulations are carried out in three loading stages. In the first
stage of loading where pile elements are not installed, self-weight,
Table 1
Material parameters used for DafaliasManzari Model [32,33].
Parameter function Parameter index Value
Elasticity G0 150.0
m 0.05
Critical state M 1.14
c 0.78
kc 0.027
e0 0.83
n 0.45
Yield surface m 0.02
Plastic modulus h0 9.7
ch 1.02
nb 2.56
Dilatancy A0 0.81
nd 1.05
Fabric-dilatancy zmax 5.0
cz 800.0
116 A. Rahmani, A. Pak / Computers and Geotechnics 40 (2012) 114126
7/25/2019 Dynamic behavior of pile foundations under cyclic loading in liquefiable soils.pdf
4/13
including both the soil skeleton and the pore water weight, are ap-
plied on soil elements. In this stage the initial stress state, void ra-
tio and soil fabric evolve. These values are used as initial values for
the next stage of loadings. The second stage includes pile installa-
tion and application of its self-weight and the superstructure
weight. Then, at the final stage, an acceleration time history is ap-
plied to the model as an input motion, and dynamic analysis are
performed for the soilpile-superstructure system.
6. Verification and validation of the numerical model
Verification is meant to identify and remove errors in computercoding and verify numerical algorithms and is desirable in quanti-
fying numerical errors in computed solution [15]. Accordingly, in
this study, due to the sophisticated methodology used to develop
a pile in a soil deposit together with an advanced constitutive
model for soil skeleton and the applied three-dimensional uP
formulation, a detailed verification is done. In the first step, the
numerical model is verified against some closed form elastic solu-
tions and benchmark problems in which a single pile is modeled in
non-liquefying soil layers under static vertical or horizontal load-
ings, e.g. Poulos and Davis[41], Aristonous et al.[42], and Kuchuk-
arsalan[43]. Comparison of results demonstrated the capability of
the numerical model to predict the result by the maximum error of
4%. In the next step, results of a centrifuge test on pile foundations
are used to demonstrate the capability of the model for reliableanalysis of piles under dynamic loading. For this purpose, the
dynamic centrifuge test of pile-supported structure in liquefiable
sand performed by Wilson et al.[7] is simulated.
The soil profile consists of two horizontal layers of saturated,
fine and uniformly graded Nevada sand (D50 = 0.15 mm, Cu= 1.5).
The lower dense layer (Dr= 80%) is 11.4 m thick, and the upper
medium dense layer (Dr= 55%) is 9.1 m thick at the prototype scale
(seeFig. 3). Furthermore, the single pile is equivalent to a steel pipe
pile with a diameter of 0.67 m and wall thickness of 19 mm at the
prototype scale. The pile is extended 3.8 m above the ground level
and carries superstructure load of 480 kN; the embedded length of
pile is about 16.8 m. The container is filled with a hydroxyl-propylmetyl-cellulose and water mixture whose viscosity is about 10
times greater than pure water.
The soilpile-superstructure system was spun at a centrifugal
acceleration of 30 g, and the pile remained elastic during earth-
quake loading.
As shown inFig. 1, the finite element mesh consists of 896 cubic
eight-node soil elements and 16 beam-column elements, four ele-
ments are used to model the free-standing length of the pile and
the rest are within the soil strata. Also, the pile head is free to move
in all directions. Properties of Nevada Sand used in the numerical
model are presented inTable 2. According to the laws of centrifuge
modeling, permeability coefficient is three times greater than the
value at the prototype scale.
The Kobe 1995 acceleration record is scaled to 0.22 g and usedas an input motion to shake the model; the base input acceleration
42.4(m)
21.0(m)
X
Y
Z
ZP
x
z
y
X : 3@5(m)[email protected](m)[email protected](m)+
[email protected](m)[email protected](m)
Y : [email protected](m)+1 @0.5(m)[email protected](m)
Z : 5@2(m) [email protected](m)+5@1(m)
ZP: 3@1(m)[email protected](m)
21.0
42.4
17.0
3.8
4.0
x
z
u-P Elements
Lumped Mass
Beam-Column Element
Input Motion
Fig. 1. Finite element mesh.
Connection Elements
Pile Elements
Interface Elements
Surrounding Soil Elements
y
x
Fig. 2. Outline of Connections between pile elements and surrounding soil
elements.
Fig. 3. Layout of the model for centrifuge test by Wilson et al. [7].
A. Rahmani, A. Pak / Computers and Geotechnics 40 (2012) 114126 117
7/25/2019 Dynamic behavior of pile foundations under cyclic loading in liquefiable soils.pdf
5/13
is shown inFig. 4. Time history of the measured and computed ex-
cess pore water pressure ratio at three different depths in the free
field: 1, 4.5, 21 m, are presented in Fig. 5. It is important to note
that in this study, excess pore water pressure ratio (ru) is defined
as the ratio of the difference of current pore pressure and hydro-
static pore pressure over the initial effective vertical stress
ru Du=r0v0. The results indicate that there is generally a goodagreement between measured and computed pore water pressure.
Fig. 6shows the computed and measured acceleration time his-
tories of the superstructure. It is concluded that the applied meth-
od is also capable of predicting the acceleration values. It is
important to note that sharp acceleration spikes can be seen corre-
sponding to sharp excess pore pressure ratio decrease at the depthof 1 m. This is due to the temporary increase in stiffness of the soil
which results in large acceleration spikes transmission from the
ground to the superstructure.
Fig. 7 shows the measured and computed bending moment
time histories at two different depths; 1 and 2 m. It can be seen
that the results obtained from the numerical model agree reason-
ably well with the values recorded during the centrifuge test.
According to the computed and measured results, the maximum
bending moment at the depth of 1 m occurs at the timet= 3.5 s.
As depicted inFig. 5, this time corresponds to sudden increase of
pore water pressure which results in the softening of surrounding
soil; and also as shown inFig. 6, the timet= 3.5 s corresponds to
the peak value of superstructure acceleration which results in a
large amount of inertial forces induced to the pile shaft. Therefore,
it can be concluded that the maximum value of bending moment
recorded and computed att= 3.5 s is the consequence of the sur-
rounding soil softening and the large amount of inertial forces
developed at the pile head.
Finally, soil displacements are compared with those recorded
during the centrifuge test.Fig. 8shows the time history of ground
surface settlement at the distance of 3 m from the pile. It is ob-
served that there is a good agreement between the computed
and measured values.
7. Parametric study
In order to provide better insights into the dynamic behavior of
piles embedded in liquefiable soil layers, a parametric study hasbeen carried out on three different soil profiles by varying
Table 2
Material parameters for Nevada sand, Popescu and Prevost [44].
Parameter Unit Value for
Dr = 55%
Value for
Dr = 80%
Porosity (n) 0.409 0.377
Saturated unit weight kN/m3 19.87 20.41
Permeability coefficient m/s 6.05 105 3.7 105
Permeability coefficient
in the prototype scale
m/s 1.815 104 1.11 104
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0 2 4 6 8 10 12 14 16 18 20
Acceleration(g)
Time (sec)
Fig. 4. Input earthquake ground motion (Acceleration record of Kobe (1995)
earthquake scaled to 0.22 g)[7].
-0.2
0
0.2
0.4
0.6
0.8
1
1.2
0 5 10 15 20 25
ExcessPorePressure
Ratio
Time (sec)
Depth = 1 m
Centrifuge Test
Simulation
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
ExcessPorePressure
Ratio
Time (sec)
Depth = 4.5 m
Centrifuge Test
Simulation
-0.2
0
0.2
0.4
0.6
0.8
1
ExcessPoreP
ressure
Ratio
Time (sec)
Depth = 21 m
Centrifuge Test
Simulation
0 5 10 15 20 25
0 5 10 15 20 25
Fig. 5. Comparison of time histories of excess pore pressure ratio in the free field at
the depths of 1, 4.5, 21 m with the centrifuge test by Wilson et al.[7].
-1.5
-1
-0.5
0
0.5
1
1.5
0 5 10 15 20 25
Acceleration
(g)
Time (sec)
Centrifuge Test
Simulation
Fig. 6. Comparison of time histories of superstructure acceleration with the
centrifuge test by Wilson et al. [7].
-3
-2
-1
0
1
2
3
0 5 10 15 20 25
BendingMom
ent(MN.m)
Time (sec)
Depth Z = 1 m
Centrifuge Test
Simulation
-3
-2
-1
0
1
2
3
0 5 10 15 20 25
BendingMoment(MN.m)
Time (sec)
Depth Z = 2 m
Centrifuge Test
Simulation
Fig. 7. Comparison of time histories of bending moment with the centrifuge test byWilson et al.[7].
118 A. Rahmani, A. Pak / Computers and Geotechnics 40 (2012) 114126
7/25/2019 Dynamic behavior of pile foundations under cyclic loading in liquefiable soils.pdf
6/13
boundary condition of pile head, pile length (L), thickness of lique-
fying soil layer (HL), relative density of liquefying soil layer (Dr)
and frequency of input motion (f). In the first profile, the ground
consists of one homogenous and liquefiable soil layer. In the sec-
ond profile, the ground is two-layered: the upper layer is liquefi-
able while the lower layer is not, and in the third one, the
ground is two-layered: the upper layer is dry and the lower layeris saturated and liquefiable. In all cases, the ground is level, and lat-
eral spreading phenomenon is not plausible. Fig. 9 shows these
profiles. It is important to note that the amplitude of input acceler-
ation is larger for the third case due to the larger values of initial
effective stress at lower layer. Amplitude of the sinusoidal input
motion is 0.15 g for the first and second soil profiles and 0.5 g for
the third soil profile.
The finite element mesh used for simulation of the proposed
soil profiles is shown inFig. 10. It consists of 1024 cubic eight-node
soil elements. The concrete pile cross section is assumed to be
square with sides (B) of 50 cm, and it is also assumed to remain
elastic during the excitation. Two different boundary conditions
are assumed at pile head: free head boundary condition in which
pile head is free to move and rotate in any direction and fixed head
boundary condition in which pile head is free to move in any direc-tion but constrained against any rotation. The material properties
of the pile and Nevada sand are shown in Table 3. In all cases,
the superstructure is simulated by a single lumped mass with a
load of 1000 kN. The input acceleration record used for the analysis
is a sinusoidal acceleration time history with 10 s duration. The
analysis has been repeated for pile lengths of 15B, 25B and 40B,
and acceleration frequencies of 1, 3, 5 and 10 Hz. For the sake of
comparison, the fully fixed pile head (against displacement and
rotation both) has also been simulated, but the results will not
be demonstrated here. The interested reader may refer to[45].
Before going into the study of the effects of mentioned
parameters on piles dynamic behavior, it is important to study
the dynamic performance of piles in each soil profile.
7.1. Pile response
The analysis has been repeated for pile lengths of 15B, 25Band
40B.Fig. 11shows maximum lateral displacement of pile and max-
imum bending moment envelops for the 40Blength pile for cases I,
II and III, respectively (due to the similar results obtained for each
pile length, only the results of the pile length of 40Bare presented
-80
-60
-40
-20
0
20
0 5 10 15 20 25
Se
ttlement(mm)
Time (sec)
Centrifuge Test
Simulation
Fig. 8. Comparison of time histories of settlement at the distance of 3 m from the
pile.
25 m
Case I Case II Case III
Liquefiable Soil
Dry Soil
W = 1000 kN
PGA = 0.5g
Dr = 40 %
Dr = 40 %
Liquefiable Soil
Dr = 40 %
W = 1000 kN
PGA = 0.15g
Nonliquefiable Soil
Dr = 85 %
Liquefiable Soil
W = 1000 kN
PGA = 0.15g
Dr = 30,40,50 %
Fig. 9. Schematic of soil profiles in cases I, II, and III.
40.5(m
)
25.0
(m)
X
Y
Z
x
z
y
X : [email protected](m)[email protected](m)[email protected](m)[email protected](m)
Y : [email protected](m)[email protected](m)[email protected](m)
Z : [email protected](m) [email protected](m)[email protected](m)
Input Motion
25.0 (m)
x
z
Lumped Massu-P Elements Beam-Column Element
40.5 (m)
Fig. 10. Finite element mesh. (Dark zone represents the pile.)
A. Rahmani, A. Pak / Computers and Geotechnics 40 (2012) 114126 119
7/25/2019 Dynamic behavior of pile foundations under cyclic loading in liquefiable soils.pdf
7/13
here). A number of observations can be made about these results.
Firstly, for case I, the maximum bending moment invariably devel-
ops at the depth of about 2 m for free-head pile, and at the pile
head for fixed-head pile (only fixed against rotation). For case II,
the maximum bending moment develops at two locations; the first
one is at the place explained for case I, and the other one is ob-
served at the depth corresponding to the interface of liquefiable
and non-liquefiable layers; however, for the third case, the secondmaximum bending moments are attained inside the lower liquefi-
able layer. Secondly, by investigating time histories of lateral dis-
placements and bending moment, it can be concluded that for all
three cases, the maximum lateral displacement of pile is attained
after when the soil layers liquefaction takes place. This is true for
the maximum bending moment which is attained at the bottom
of liquefiable layer; however, the maximum bending moment near
the pile top, develops at the first moments of dynamic loadings be-
fore liquefaction.
Ishihara [46] indicated that inertial forces which are the pre-
dominant forces before liquefaction are mainly responsible for
development of maximum bending moment near the pile head,
and kinematic forces which are predominant after liquefaction
are responsible for the maximum bending moment observed atthe interface of liquefiable and non-liquefiable layers. This is con-
firmed by the numerical method; the results are shown inFig. 12
in which the maximum bending moment envelops of 25B and
40B length piles are obtained for piles with and without super-
structure mass. It is interesting to observe that when the super-
structure is removed, the maximum bending moment near the
pile head decreases significantly, and no peak values are observed
at that location; while values at depths below 5 m are approxi-
mately unchanged. In other words, the same kinematic forces have
been developed in piles with and without superstructure.
For more clarification of the issue, the performance of a pile
embedded in a dry ground is compared with the dynamic perfor-
mance of a pile embedded in a saturated (i.e. liquefiable) ground.
The obtained results for a free-head and fixed-head pile in Case IIare shown inFig. 13. It is concluded that in dry grounds, the lateral
displacements of the pile are significantly less than the values cal-
culated in a saturated ground. This is due to the fact that lateral
displacement of dry soil is far less than lateral displacement of sat-
urated soil; so little kinematic forces are exerted to the pile embed-
ded in a dry ground.
7.2. Soil response
To investigate the effect of pile foundations on the surrounding
soil response, excess pore water pressure time histories computed
near the pile are compared with those computed in the free field at
two different depths. The results are shown in Fig. 14 for a pile
with a length of 40B (21 m) in case I. It can be seen that at thedepth of 1 m (near the pile head), the time history of excess pore
water pressure near the pile is significantly different from the
one in the free field during excitation period, while after excitation
(from 10 to 25 s), time histories are nearly identical. Since the dif-
ference between time histories decreases in the depth far from pile
head (i.e. depth of 15 m), the dynamic response of superstructure
seems to be responsible for the observed behavior. In other words,
inertial forces from the superstructure caused the pile top to vi-
brate in a completely different nature from the surrounding soil,and this leads to larger shear strains exerted to the soil which leads
to temporary dilation and contraction behavior. It is to be noted
that as seen inFig. 12 inertial forces only affect pile top sections.
For this, time histories of excess pore water pressure near the pile
and in the free field are approximately identical at deeper depths.
Furthermore, lateral displacement of soil near the pile is com-
pared with the lateral displacement of soil in the free field before
and after liquefaction of the ground. The results are shown in
Fig. 15 for case I and III (The results obtained for case I is same
as case II). It is noted that the lateral displacement envelope of
the soil near pile and the soil in the free field have an identical
trend before the ground liquefies while there is a significant differ-
ence between the lateral displacement of soil near the pile and the
soil in the free field after liquefaction occurs. Accordingly, it seemsthat dynamic response of pile entirely differs from dynamic re-
sponse of soil after liquefaction.
7.3. Effect of pile length on pile performance
In this section, results obtained from repetitive analysis for pile
lengths of 15B, 25Band 40Bfor three different soil profiles are dis-
cussed (B= pile width). Due to the similarity of results for three
cases, only the results of case II are presented inFig. 16. It is con-
cluded that for all three profiles and any pile head boundary con-
ditions, pile length has no effect on maximum lateral
displacement of pile during excitation (i.e. from 0 to 10 s) while
significant changes are observed after excitation period (i.e. from
10 to 25 s); a change of about 15Bin pile length results in a changeof 2040% in maximum value of pile lateral displacement. Ariston-
ous et al.[42] and many other researchers reported that for piles
embedded in dry soil layers, pile length has a little effect on pile
lateral displacements. However, in this study, it is concluded that
pile length significantly affects pile lateral displacements after
excitation. From t= 10 s to t= 25 s, inertial forces are minimum
not only because the excitation has finished but also because soil
layers have liquefied so the kinematic forces, which are predomi-
nant, are exerted to the longer pile since the longer pile is in touch
with greater amount of the liquefied soil.
Fig. 17shows the maximum bending moment envelops of free-
head and fixed-head piles with lengths of 15B, 25Band 40B. In all
cases, it can be concluded that pile length has no effect on the place
of maximum bending moment, and the maximum value always at-tained at pile head or at the depth of about 2 m.
Table 3
The material properties of the pile and Nevada sand used in the numerical model.
Material Parameter Value
Pile
Youngs Modulus, (kPa) Ep 3.0 107
Density, (ton/m3) qp 2.40Poissons Ratio mp 0.2
Material Parameter Value
Soil Dr = 30% Dr = 40% Dr = 50% Dr = 85%
Soil density (ton/m3) qsat 1.938 1.957 1.976 2.052Fluid density (ton/m3) qf 1.0 1.0 1.0 1.0Porosity n 0.438 0.427 0.415 0.370
Permeability (m/s) k 7. 5 105 6.6 105 5.9 105 3.7 105
120 A. Rahmani, A. Pak / Computers and Geotechnics 40 (2012) 114126
7/25/2019 Dynamic behavior of pile foundations under cyclic loading in liquefiable soils.pdf
8/13
7.4. Effect of frequency of excitation on pile performance
Fig. 18shows maximum lateral displacement of pile, maximum
bending moment and pile head settlement time histories for differ-ent frequencies of excitation; 1, 3, 5 and 10 Hz. It is noted that the
frequency has a significant effect on pile response. For example, by
increasing the frequency from 3 Hz to 10 Hz, maximum lateral dis-
placement, maximum bending moment and settlement decreases
about 75%, 90% and 70%, respectively. Since acceleration amplitudeof the input motion is the same in all analysis, displacement
(a)
(b)
(c)
-25
-20
-15
-10
-5
0
0 0.5 1 1.5 2
Depth(m)
Maximum Lateral Disp. (cm)
Fixed HeadFree Head
-25
-20
-15
-10
-5
0
0 50 100 150
De
pth(m)
Maximum Bending Moment
(kN.m)
-25
-20
-15
-10
-5
0
0 100 200 300
De
pth(m)
Maximum Bending Moment
(kN.m)
-25
-20
-15
-10
-5
0
0 0.5 1 1.5 2
Depth(m)
Maximum Lateral Disp. (cm)
Fixed Head
Free Head-25
-20
-15
-10
-5
0
0 50 100 150
Depth(m)
Maximum Bending Moment
(kN.m)
-25
-20
-15
-10
-5
0
0 100 200 300
Depth(m)
Maximum Bending Moment
(kN.m)
-25
-20
-15
-10
-5
0
0 2 4 6
De
pth(m)
Maximum Lateral Disp. (cm)
Fixed Head
Free Head-25
-20
-15
-10
-5
0
0 100 200 300
Dep
th(m)
Maximum Bending Moment(kN.m)
-25
-20
-15
-10
-5
0
0 200 400 600
Depth(m)
Maximum Bending Moment
(kN.m)
Free Head Fixed Head
Free Head
Free Head Fixed Head
Fixed Head
Fig. 11. Maximum lateral displacement and maximum bending moment envelops for a free-head and fixed-head (fixed against rotation) pile in (a) Case I (b) Case II
(Thickness of liquefiable layer is 11 m.) (c) Case III (Thickness of dry layer is 5 m.).
-16
-12
-8
-4
0
0 50 100 150
Depth(m)
Maximum Bending Moment (kN.m)
Without SS Mass
With SS Mass
-25
-20
-15
-10
-5
0
0 50 100 150
Depth(m)
Maximum Bending Moment (kN.m)
Without SS Mass
With SS Mass
Pile Length = 25B Pile Length = 40B
Fig. 12. Maximum bending moment envelops for pile lengths of 25B and 40B (B: pile width) with and without superstructure mass (Case I).
A. Rahmani, A. Pak / Computers and Geotechnics 40 (2012) 114126 121
7/25/2019 Dynamic behavior of pile foundations under cyclic loading in liquefiable soils.pdf
9/13
7/25/2019 Dynamic behavior of pile foundations under cyclic loading in liquefiable soils.pdf
10/13
compared to that corresponding to dry soils. According to the re-
sults, if the pile head is fixed against rotations, maximum bending
moment increases about 95% for case I, 130% for case II and 95% forcase III. However, in dry ground, pile head fixity leads to nearly 20%
increase in maximum bending moment. In liquefying soils, when
the pile head is restrained rotationally, relative lateral displace-
ment of pile at upper and lower regions significantly increases
due to liquefaction of surrounding soil (it can be seen in Fig. 13);
larger relative lateral displacements lead to larger bending mo-
ment so boundary condition of pile head has a big effect on bend-
ing moment in the cases where the ground liquefies.
7.6. Effect of thickness of liquefiable soil layer on pile performance
In this section, results obtained from repetitive analysis for
thickness of liquefiable layers(HL) of 5 m, 11 m and 15 m for a
pile length of 40B (i.e. 21 m) are discussed. This parameter isinvestigated only for the Case II.Fig. 19 shows maximum lateral
displacement of the pile for various thicknesses of liquefiable lay-
ers. It is concluded that the thickness of liquefiable soil layer has a
little effect on maximum lateral displacement of pile during exci-tation (i.e. from 0 to 10 s) while significant changes are observed
after excitation period (i.e. from 10 to 25 s). According to the re-
sults, twice increase in the thickness of liquefiable layer leads to
about twice increase in the maximum lateral displacement of pile.
As mentioned before, after excitation period, piles are intensely un-
der the control of the surrounding liquefied soil, so thicker liquefi-
able layer considerably affects pile lateral displacements which can
be very important in performance-based design approaches.
Fig. 20 shows maximum bending moment envelops of free-
head and fixed-head pile for thickness of liquefiable layers(HL) of
5 m, 11 m and 15 m for a pile length of 40B (i.e. 21 m). The maxi-
mum bending moment developed at the interface is investigated. It
is concluded that when the thickness is 5 m, there is 40% difference
between the value obtained for free-head pile and the value forfixed-head pile. However, for the thickness of 11 m and 15 m the
-25
-20
-15
-10
-5
0
0 0.5 1 1.5 2
Depth(m)
Maximum Lateral Displacement (cm)
L/B= 15 ( HL = 4 m)
L/B= 25 ( HL = 6.5 m)
L/B= 40 ( HL = 11 m)-25
-20
-15
-10
-5
0
0 1 2 3
Depth(m)
Maximum Lateral Displacement (cm)
L/B= 15 ( HL = 4 m)
L/B= 25 ( HL = 6.5 m)
L/B= 40 ( HL = 11 m)(a) (b)
Fig. 16. Comparison of pile maximum lateral displacement for different pile lengths in Case II (a) during excitation ( t= 010 s) and (b) after excitation (t= 1025 s) (L: pile
length, B: pile width, HL: thickness of liquefiable layer).
-25
-20
-15
-10
-5
0
0 50 100 150 200
Depth
(m)
Maximum Bending Moment (kN.m)
L/B= 15 ( HL = 4 m)
L/B= 25 ( HL = 6.5 m)
L/B= 40 ( HL = 11 m)-25
-20
-15
-10
-5
0
0 100 200 300 400
Depth
(m)
Maximum Bending Moment (kN.m)
L/B=15 (HL = 4 m)
L/B=25 (HL = 6.5 m)
L/B=40 (HL = 11 m)Free Head Fixed Head
Fig. 17. Comparison of maximum bending moment for different pile lengths for free-head and fixed-head(against rotation) pile in Case II (L: pile length, B: pile width, HL:
thickness of liquefiable layer).
-25
-20
-15
-10
-5
0
0 5 10 15
Depth(m)
Maximum Lateral Disp. (cm)
f = 1 Hz
f = 3 Hz
f = 5 Hz
f = 10 Hz
-25
-20
-15
-10
-5
0
0 200 400 600 800
Depth(m)
Maximum Bending Moment (kN.m)
f = 1 Hz
f = 3 Hz
f = 5 Hz
f = 10 Hz-0.2
-0.15
-0.1
-0.05
0
0 10 20
PileHeadSettlement
(m)
Time (sec)
f= 3 Hz
f=5 Hz
f= 10 Hz
Fig. 18. Variation of maximum lateral displacement, maximum bending moment and pile head settlement for different frequencies of input excitation in Case I.
A. Rahmani, A. Pak / Computers and Geotechnics 40 (2012) 114126 123
7/25/2019 Dynamic behavior of pile foundations under cyclic loading in liquefiable soils.pdf
11/13
difference is nearly 14% and 0%, respectively. Results of numerical
analysis indicate that when the thickness of the liquefying layer
exceeds about one-fourth of the pile length, bending moment at
the interface does not depend on the boundary condition at the
pile head. It is worth mentioning that Liyanapathirana and Poulos
[19]reported this conclusion for the thickness of one-third of the
total thickness of the soil deposit using one-dimensional WinklerModel.
Also, the effect of thickness of liquefiable soil layer on pile head
settlement is investigated in this study.Fig. 21shows variation of
pile head settlement by the increase of thickness of liquefying layer
for the pile lengths of 13 m and 21 m. It is noted that the increase
of the thickness of the liquefying layer has a little influence on pile
settlement when bottom of the liquefiable layer is far from the pile
toe while the settlement sharply increases by approaching the liq-
uefiable layer to the pile toe. It is commonly known that total set-tlement of piles is mainly due to the settlement of the soil in the
vicinity of pile toe. Therefore, when the liquefiable layer gets closer
to the pile toe, settlement of pile head considerably increases.
7.7. Effect of relative density of liquefiable soil layer on pile
performance
In this section, results obtained from repetitive analysis for
three different relative densities; 30%, 40% and 50% for a pile length
of 40B are discussed.Fig. 22shows the maximum lateral deflection
and maximum bending moment envelops for different relative
densities. It is observed that for the pile embedded in Nevada sand
layers, about 10% increase of relative density causes 15% decreasein maximum value of lateral displacement and an average value of
-25
-20
-15
-10
-5
0
0 0.5 1 1.5 2
D
epth(m)
Maximum Lateral Displacement (cm)
HL = 5 (m)
HL = 11 (m)
HL = 15 (m)-25
-20
-15
-10
-5
0
0 1 2 3 4 5
D
epth(m)
Maximum Lateral Displacement (cm)
HL = 5 (m)
HL = 11 (m)
HL = 15 (m)(b)(a)
Fig. 19. Variation of maximum lateral displacement for various thicknesses of liquefiable layers in Case II (a) during excitation ( t= 010 s) and (b) after excitation (t= 10
25 s).
-25
-20
-15
-10
-5
0
0 100 200 300
Depth(m)
Maximum Bending Moment (kN.m)
Fixed Head
Free Head-25
-20
-15
-10
-5
0
0 100 200 300
Depth(m)
Maximum Bending Moment (kN.m)
Fixed Head
Free Head
-25
-20
-15
-10
-5
0
0 100 200 300
Depth(m)
Maximum Bending Moment (kN.m)
Fixed Head
Free Head
HL= 5 m
HL= 15 m
HL= 11 m
Fig. 20. Bending moment envelops for a 40B length (B: pile width) free-head and fixed-head pile in Case II.
0
5
10
15
20
25
0 5 10 15 20 25 30
Pile
HeadSettlement(cm)
Thickness of Liquefiable Layer (m)
L = 13 (m)
L = 21 (m)
Fig. 21. Variation of pile head settlement by the increase of thickness of liquefying
layer for the pile lengths(L) of 13 m and 21 m (Case II).
124 A. Rahmani, A. Pak / Computers and Geotechnics 40 (2012) 114126
7/25/2019 Dynamic behavior of pile foundations under cyclic loading in liquefiable soils.pdf
12/13
30% decrease in the value of the bending moment. This is due to
the increase of the liquefiable soil stiffness and smaller values of
soil displacement.
8. Conclusions
This paper tries to provide better insight into the performance
of pile foundations embedded in liquefiable soil deposits. For this,
an accurate methodology for numerical modeling of piles in lique-
fiable soils is employed. A fully coupleduPformulation is used to
analyze soil displacements and pore water pressures, and a bound-
ing surface critical state elasticplastic model that accounts for
fabric change is employed to model the soil skeleton. Moreover,
the permeability coefficient is updated in each time step as a func-
tion of excess pore water pressure ratio. Results from a centrifuge
test are simulated and the obtained results demonstrate that the
numerical model has the ability to simulate pile behavior in lique-
fying soil reasonably well.
Parametric studies are carried out for three different soil pro-
files. For each profile, the effect of pile length, fixity of the pile
head, frequency of input motion, the thickness of liquefying soillayer and the effect of relative density of liquefying soil layer on
pile performance are investigated. A summary of the findings are
mentioned below:
It is found that for any values of the mentioned parameters and
for all three soil profiles, the maximum lateral displacement of
free-head pile develops at pile head. Also, it is concluded that in
all cases the maximum bending moment develops at about 2 m
from pile top for free-head piles and at pile head for fixed-head
piles. Besides, for case II and III there is other peak values of bend-
ing moment at the interface of liquefiable and non-liquefiable lay-
ers and inside the liquefying layer, respectively.
Due to the fact that pile dynamic response near the ground sur-
face is approximately under the control of dynamic response of
superstructure, the pile has a significant influence on the seismicresponse of the surrounding soil near the ground surface. Further-
more, the results of the numerical model demonstrate that pile re-
sponse is different from the response of soil in the free field after
liquefaction while before liquefaction there is a little difference.
For all cases, it is shown that pile length and the thickness of liq-
uefiable layer have little influences on the maximum lateral dis-
placements during excitation; however, when the input
excitation finishes there are considerable differences in the maxi-
mum values of the lateral displacements for different pile lengths.
It is also shown that pile length has no effect on the location of the
maximum bending moment.
For all cases, it is concluded that natural frequency of earth-
quake highly affects pile performance in liquefiable soil deposits.
It is shown that if the frequency of the input motion increaseswhile the amplitude of acceleration remains constant, lateral
displacement, bending moment and pile head settlement signifi-
cantly decrease.
When the pile head rotation is fixed in all directions, the max-
imum lateral displacement of pile embedded in dry soil layers re-
duces much more compared to that in saturated liquefiable soil
layers. But maximum bending moment in saturated soil deposits
significantly increases. Generally, it is concluded that in liquefiableground, restraining pile head results in the development of larger
bending moment at the pile head although it decreases pile lateral
displacements; therefore, it is recommended that if the allowable
lateral displacement of superstructure and pile embedded in lique-
fiable ground is large enough, the application of hinge joint at pile
head is much more efficient than the application of restrained
joint.
It is also shown that if the thickness of the liquefying layer
exceeds one-fourth of pile length, the bending moment at the
interface does not depend on the boundary condition at the pile
head. Moreover, it is found that 10% increase in relative density
of liquefiable soil layer results in approximately 1530% decrease
in the maximum lateral displacement and maximum bending
moment.In general, parametric studies have shown that frequency of
excitation, pile head fixity and the thickness of liquefiable layer
have higher effects on pile response compared to the other param-
eters. Therefore, the key to good designs is reliable estimates of
these parameters.
References
[1] Kramer SL. Geotechnical earthquake engineering. New Jersey: Prentice HallInc.; 1996. p. 348422.
[2] Hamada M. Large ground deformation and their effects on lifelines: 1983Nihokai-Chubu earthquake. In: Hamada M, ORourke T, editors. Case studies ofliquefaction and lifeline performance during past earthquake, (I): Japanesecase studies, vol. 4-1; 1992. p. 485 [chapter 4].
[3] Mori S, Namuta A, Miwa S. Feature of liquefaction damage during the 1993Hokkaido Nanseioki earthquake. In: Proceedings of the 29th annual conferenceof Japanese Society of soil mechanics and foundation engineering; 1994. p.100508.
[4] Tachikawa H, Fujii S, Onishi K, Suzuki Y, Isemoto N, Shirahama M. Investigationand analysis of pile foundation located on Kobe Port Island. In: Proceedings ofthe 33rd Japan national conference on geotechnology engineering, vol. 1; 1998.p. 8112.
[5] Shamoto Y, Sato M, Futaki M, Shimazu S. Site investigation of post liquefactionlateral displacement of pile foundation in reclaimed land. Tsuchi to Kiso1996;44(3):257.
[6] Onishi K, Namba S, Sento N, Horii K, Tatsumi Y, Oh-Oka H. Investigation offailure and deformation modes of piles throughout overall length. Tsuchi toKiso 1996(45):246.
[7] Wilson DW. Soil pile superstructure interaction in liquefying sand and softclay, Ph.D. Dissertation, University of California at Davis; 1998.
[8] Yao S, Kobayashi K, Yoshida N, Matsuo H. Interactive behavior of soilpile-superstructure system in transient state to liquefaction by means of largeshake table tests. Soil Dyn Earthquake Eng 2004;24:397409.
[9] Abdoun T, Dobry R. Evaluation of pile foundation response to lateral spreading.Soil Dyn Earthquake Eng 2002;22:10518.
-25
-20
-15
-10
-5
0
0 1 2 3 4
Depth(m)
Maximum Lateral Disp. (cm)
Dr = 30 %
Dr = 40 %
Dr = 50 %
-25
-20
-15
-10
-5
0
0 100 200 300
Depth(m)
Maximum Benidng Moment (kN.m)
Dr = 30 %
Dr = 40 %
Dr = 50 %
Fig. 22. Variation of pile maximum lateral displacement and maximum bending moment by the increase of relative density of liquefiable soil layer in Case II (pile head: fixed
against rotation and HL = 11 m).
A. Rahmani, A. Pak / Computers and Geotechnics 40 (2012) 114126 125
7/25/2019 Dynamic behavior of pile foundations under cyclic loading in liquefiable soils.pdf
13/13
[10] Suzuki H, Tokimatsu K, Sato M, Abe A. Factor affecting horizontal subgradereaction of piles during soil liquefaction and lateral spreading, Geotechnical SPNo.145, ASCE; 2005. p. 19.
[11] Dungca JR, Kuwano J, Takahashi A, Saruwatari T, Izawa J, Suzuki H, et al.Shaking table tests on the lateral response of a pile buried in liquefied sand.Soil Dyn Earthquake Eng 2006;26:28795.
[12] Bhattacharya S, Madabhushi PG, Bolton MD. An alternative mechanism of pilefailure in liquefiable deposits during earthquakes. Geotechnique 2004(3):20313.
[13] Tamura S, Tokimatsu K. Seismic earth pressure acting on embedded footing
based on large-scale shaking table tests, Geotechnical SP No.145, ASCE; 2005.p. 8395.
[14] Han J, Kim SR, Hwang JI, Kim MM. Evaluation of the dynamic characteristics ofsoilpile system in liquefiable ground by shaking table tests. In: 4thInternational conference on earthquake geotechnical engineering.Thessaloniki, Greece; 2007. p. 1340.
[15] Cheng Zh, Jeremic B. Numerical modeling and simulation of pile in liquefiablesoil. Soil Dyn Earthquake Eng 2009;29:140416.
[16] Kagawa T. Lateral pile response in liquefying sand. In: Proceedings of the 10thworld conference on earthquake engineering, Madrid, Spain; 1992, Paper No.1761.
[17] Yao S, Nogami T. Lateral cyclic response of piles in viscoelastic Winklersubgrade. J Eng Mech 1994;120(4):75875.
[18] Fuji S, Cubrinovski M, Tokimatsu K, Hayashi T. Analyses of damaged andundamaged pile foundations in liquefied soils during the 1995 KobeEarthquake. In: Proceedings of the 1998 conference on geotechnicalearthquake engineering and soil dynamics III, Seattle, Wash., vol. 2; 1998. p.118798.
[19] Liyanapathirana DS, Poulos HG. Seismic lateral response of piles in liquefyingsoil. J Geotech Geoenviron Eng 2005(1311):146679.
[20] Miwa S, Ikeda T, Sato T. Damage process of pile foundation in liquefied groundduring strong ground motion. Soil Dyn Earthquake Eng 2005;26:32536.
[21] Liyanapathirana DS, Poulos HG. Analysis of pile behaviour in liquefying slopingground. J Comput Geotech 2009;37:11524.
[22] Chang DW, Lin BS, Cheng SH. Dynamic pile behaviors affecting by liquefactionfrom EQWEAP analysis. In: 4th International conference on earthquakegeotechnical engineering. Thessaloniki Greece; 2007. p. 1336.
[23] Finn WDL, Fujita N. Pile in liquefiable soils: seismic analysis and design issues.Soil Dyn Earthquake Eng 2002;22:73142.
[24] Klar A, Baker R, Frydman S. Seismic soilpile interaction in liquefiable soil. SoilDyn Earthquake Eng 2004;24:55164.
[25] Oka F, Lu CW, Uzuoka R, Zhang F. Numerical study of structure-soil-group pilefoundations using an effective stress based liquefaction analysis method. In:13th World conference on earthquake engineering. Canada: Vancouver; 2004.p. 3338.
[26] Uzuoka R, Sento N, Kazama M. Three-dimensional numerical simulation ofearthquake damage to group-piles in a liquefied ground. Soil Dyn Earthquake
Eng 2007;27:395413.[27] Comodromos EM, Papadopoulou MC, Rentzepris IK. Pile foundation analysis
and design using experimental data and 3-D numerical analysis. ComputGeotech 2009;36:81936.
[28] Zienkiewicz OC, Shiomi T. Dynamic behavior of saturated porous media; thegeneralized Biot formulation and its numerical solution. Int J Numer MethodsEng 1984;8:7196.
[29] Jeremic B. Development of geotechnical capabilities in OpenSees, Report no.PEER2001/12, Pacific Earthquake Engineering Research Center; 2001.
[30] Mazzoni Silvia, McKenna Frank, Fenves Gregory L. Open system for earthquakeengineering simulation user manual. Berkeley: Pacific Earthquake EngineeringResearch Center, University of California; 1999. .
[31] Dafalias YF, Manzari MT. Simple plasticity sand model accounting for fabric
change effects. J Eng Mech 2004;130(6):62234.[32] Shahir H. A performance-based approach for design of ground densification for
mitigation of liquefaction, Ph.D. Dissertation, Sharif University of Technology;2009.
[33] Shahir H, Pak A. Estimation of liquefaction-induced settlement of shallowfoundations by numerical approach. Comput Geotech 2010;37:26779.
[34] Dafalias YF. Overview of constitutive model used in VELACS. In: Arulanandan,Scott, editors. Verification of numerical procedures for the analysis of soilliquefaction problems, vol. II, Rotterdam, Balkema; 1993.
[35] Arulanandan K, Sybico Jr J., Post liquefaction settlement of sand. In: Proceedingof the wroth memorial symposium. England: Oxford University; 1992.
[36] Jafarzadeh F, Yanagisawa E. Settlement of sand models under unidirectionalshaking. In: Ishihara K, editor. First international conference on earthquakegeotechnical engineering, IS-Tokyo; 1995. p. 693698.
[37] Manzari MT, Arulanandan K. Numerical predictions for Model No. 1. In:Arulanandan K, Scott RF, editors. Verification of numerical procedures for theanalysis of soil liquefaction problems. Rotterdam: A.A. Balkema; 1993. p.17985.
[38] Balakrishnan A. Liquefaction remediation at a bridge site, Ph.D. Dissertation.Davis: University of California; 2000.
[39] Taiebat M, Shahir H, Pak A. Study of pore pressure variation duringliquefaction using two constitutive models for sand. Soil Dyn EarthquakeEng 2007;27(1):6072.
[40] Shahir H, Pak A. Variation of permeability during liquefaction and its effects onseismic response of saturated sand deposits. In: 8th International Congress onCivil Engineering, Shiraz, Iran; 2009.
[41] Polos HG, Davis EH. Pile foundation analysis and design. New York, NY: JohnWiley and Sons; 1980 [chapters 8 and 15].
[42] Trochanis Aristonous M, Bielak Jacobo, Christiano Paul. Three-dimensionalnonlinear study of piles. J Geotech Geoenviron Eng 1991;117(3):42947.
[43] Kucukarsalan S. Linear and non-linear soilpile-structure interaction understatic and transient impact loading, PhD Dissertation, State University of NewYork at Buffalo; 1999. p. 18898 [Chapter 6].
[44] Popescu R, Prevost JH. Centrifuge validation of a numerical model for dynamicsoil liquefaction. Soil Dyn Earthquake Eng 1993;12:7390.
[45] Rahmani A. Dynamic analysis of pile foundations embedded in liquefiablesoils, Masters Dissertation, Sharif University of Technology; 2010.
[46] Ishihara K., Terzaghi oration: geotechnical aspects of the 1995 Kobeearthquake. In: Proceedings of ICSMFE, Hamburg, 1997, pp. 20472073.
126 A. Rahmani, A. Pak / Computers and Geotechnics 40 (2012) 114126
http://opensees.berkeley.edu/http://opensees.berkeley.edu/http://opensees.berkeley.edu/http://opensees.berkeley.edu/