Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
E SeriesQuick Start GuideInput ConfigurationE Series two-way loudspeakers and subwoofers are designed for externally powered operation. Pass-throughs permit connection to multiple loudspeakers. The two-way models feature internal passive crossovers for full-range operation. To use them with subwoofers, use an active crossover and separate amplification to split the subwoofer frequencies and the remainder of the audio spectrum.
PLD and GXD Series amplifiers have E Series voicings available in their presets and loudspeaker profiles. TouchMix digital mixers also have E Series voicings available, for use in systems that don't have PLD or GXD Series amplifiers.
E Series E110, E112, E115, E215 Block Diagram and Input Plate
— Figure 1 —
LF
E215 only
DEEP LPF
HPF HF
LPF LF
NL4
BarrierStrip
NL4
1
1
1
1
22
22
E Series E118sw, E218sw Block Diagram and Input Plate
— Figure 2 —
LF
LF
NL4
BarrierStrip
NL4
1
1
1
1
E218sw only
22
22
TD-000525-00-E
*TD-000525-00*
2TD-000525-00-E
ConnectionsFull Range Stereo System
— Figure 3 —
Input
NL4Amplifier
1122
NL4Loudspeaker
1122
NL4Amplifier
1122
NL4Loudspeaker
1122
Right
Left
Single Channel, Sub / Satellite Option 1
— Figure 4 —
Input
NL4Amplifier
1122
NL4Loudspeaker
1122
NL4Amplifier
1122
NL4Loudspeaker
1122
GXD Series power amplifier preset:P6 ST E110 (stereo E110) P10 ST E112 (stereo E112) P12 ST E112 DANCE (stereo E112 dance) P14 ST E115 (stereo E115) P16 ST E115 DANCE (stereo E115 dance)
GXD Series power amplifier preset:P3 SUB SAT 80HZ
3TD-000525-00-E
Single Channel, Sub / Satellite Option 2
— Figure 5 —
Input
Cross-wired 1 - 2, 2 - 1
NL4Amplifier
1122
NL4Loudspeaker
1122
NL4Amplifier
1122
NL4Loudspeaker
1122
Dual Channel, Sub / Satellite System
— Figure 6 —
to RightSubwoofer
to LeftSubwoofer
to LeftSatellite
to RightSatellite
Input
NL4Amplifier
NL4Loudspeaker
1122
1122
NL4Amplifier
1122
NL4Loudspeaker
1122
Right
Left
GXD Series power amplifier preset:P7 ST E110 + SUB P8 ST E110 DANCE + SUB P11 ST E112 + SUB P12 ST E112 DANCE + SUB P15 ST E115 + SUB P17 ST E115 DANCE + SUB
GXD Series power amplifier preset:P3 SUB SAT 80HZ
GXD Series power amplifier preset:P18 ST E118 SUBS
4TD-000525-00-E
Dual Channel, Sub / Satellite System with 4-channel PLD
— Figure 7 —
Channels C & Dto RightSubwoofer &Satellite
Channel Bto LeftSatellite
Channel Ato LeftSubwoofer
Right
Input
Cross-wired 1 - 2, 2 - 1
NL4Amplifier
1122
NL4Loudspeaker
1122
NL4Amplifier
1122
NL4Loudspeaker
1122
NL4Amplifier
1122
NL4Loudspeaker
1122
NL4Amplifier
1122
NL4Loudspeaker
1122
Option 1:Two 2-conductorcables
Option 2:4-conductorcable
Left
PLD Series power amplifier preset:F11 Dual bi-amp mode
PLD Series power amplifier loudspeaker profiles:
CH A • E118sw• E218sw
CH B • E110 +SUB• E112 +SUB• E112 dance +SUB• E115 +SUB• E115 dance +SUB• E215 +SUB• E215 dance + SUB
CH C • E118sw• E218sw
CH D • E110 +SUB• E112 +SUB• E112 dance +SUB• E115 +SUB• E115 dance +SUB• E215 +SUB• E215 dance + SUB
5TD-000525-00-E
Pole Mounting on E118swThe E Series loudspeakers (E110, E112, E115) can be mounted above the E118sw subwoofer using the 36-inch pole included with the subwoofer. NOTE: The E215 loudspeaker does not offer a pole mounting option.
WRNINNG: This pole, if used inappropriately, may make the loudspeaker system top-heavy and hazardous. Ensure that your system will resist tipping and that it sits on a solid, level surface.
WRNINNG: Always use two persons to lift the loudspeaker onto the pole. Do not move a subwoofer if a loudspeaker and pole are mounted on it.
Refer to — Figure 8
1. Place the E118sw subwoofer (1) on a solid level surface positioned where you want to use it.
2. Screw the threaded end of the 36-inch mounting pole (3) clockwise into the pole-mounting bracket (2) on top of the subwoofer. Hand tighten only.
3. Select one of the two pole mount cups on the E Series loudspeaker:
• The rear cup (4) has no tilt.
• The front cup (5) gives a downward tilt of 10°.
4. Carefully place the loudspeaker onto the pole.
Installation OptionsThe following options require purchasing an accessory kit designed for the E Series loudspeakers.
Yoke Mounting the Loudspeakers
A yoke accessory allows the E110, E112, or E115 to be mounted on a surface, such as a wall or ceiling. The E118sw and E218sw subwoofers cannot be yoke-mounted. Each model has a corresponding yoke accessory kit:
• E110 Yoke Accessory Kit: E110 Yoke
• E112 Yoke Accessory Kit: E12 Yoke
• E115 Yoke Accessory Kit: E15 Yoke
Suspending the Loudspeakers
A pair of E110 loudspeakers can be suspended using the M8 Suspension Kit M8 KIT W, which contains six eye bolts and six washers.
To suspend an E112, E115, or E215 loudspeaker, use the M10 KIT- , which contains three eye bolts.
The E118sw and E218sw subwoofers cannot be suspended.
Always consult a licensed and qualified rigger or structural engineer before suspending any loudspeaker.
Subwoofer Caster Kits
Optional casters are available to install on the subwoofer models to make them more mobile and ideal for use in portable sound systems.
Both the E118sw and the E218sw subwoofers use a kit of two locking and two non-locking 4-inch casters with 16 mounting screws, QSC part number FG-901156-00 (one kit needed per subwoofer).
— Figure 8 —
54
3
2
1
6TD-000525-00-E
Mailing Address:
QSC, LLC
1675 MacArthur Boulevard
Costa Mesa, CA 92626-1468 USA
Telephone Numbers:
Main Number: +1 (714) 754-6175
Sales & Marketing: +1 (714) 957-7100 or toll free (USA only) (800) 854-4079
Customer Service: +1 (714) 957-7150 or toll free (USA only) (800) 772-2834
Facsimile Numbers:
Sales & Marketing FAX: +1 (714) 754-6174
Customer Service FAX: +1 (714) 754-6173
World Wide Web:
www.qsc.com
E-mail:
© 2016 QSC, LLC. All rights reserved. QSC and the QSC logo are registered trademarks of QSC, LLC in the U.S. Patent and Trademark office and other countries. All other trademarks are the property of their respective owners.
http://patents.qsc.com.