Upload
veeraboss
View
269
Download
11
Embed Size (px)
Citation preview
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
1/21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ing
onan
dcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tionof
itscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
E-terraControl V3.4 & PACiS V4.2
Integration Guide
DISTRIBUTION
Confidentiality CategoryRestricted Normal
Control CategoryControlled Not Controlled
Identification number Identification letters Issue T r a n s m i s s i o n & D i s t r i b u t i o n
2059660 IG AAREVA T&D PCL, Avenue de Figuires BP75
34975 Lattes Cedex - France
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
2/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 2 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
Intended blank page
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
3/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 3 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
APPROVAL SIGNATURES
NAME POSITION DATE SIGNATURE
J-M BOISSET PACIS PROJECTMANAGER
M. VERNEY R&D GROUP MANAGERVALIDATION & SUPPORT
RECORD OF REVISION
ISSUE DATE AUTHOR COMMENTS
Z 24/02/06 JP. MALRIC Draft
A 17/11/06 JP. MALRIC First issue
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
4/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 4 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
TABLE OF CONTENTS
1. INTRODUCTION............ ............. .............. ............. ............. ............. .............. ............. ............ .............. ......6
1.1 DOCUMENTOBJECTIVE........................................................................................................................61.2 WHO SHOULD USE THIS DOCUMENT ...........................................................................................................6 1.3 OPERATING SYSTEM SUPPORT.....................................................................................................................6 1.4 REFERENCEDOCUMENTS ....................................................................................................................61.5 ABBREVIATIONS ....................................................................................................................................71.6 COMPATIBILITY ...........................................................................................................................................7
2.
INSTALLATION ............ ............. ............ .............. ............. ............ .............. ............. .............. ............ .........8
2.1 E-TERRACONTROL V3.4...............................................................................................................................8 2.2 PACISCOMMUNICATIONS AGENCY V3.22A ...............................................................................................8
2.2.1 Installing the communications Agency ............ ............. ............ .............. ............. .............. ............ .........82.2.2 Installing SISCO MMS driver software............. ............. ............. .............. ............. ............ .............. ......82.2.3 IEC61850 Client needs Anonymous RPCs with Service Pack 2.. .............. ............. ............ .............. ....10
3. CONFIGURATION............ ............. ............ .............. ............. .............. ............ ............. .............. ............. ..11
3.1 PURPOSE ....................................................................................................................................................11 3.2 IEC61850 .................................................................................................................................................11
3.2.1 Agency application ............. ............ .............. ............. .............. ............ .............. ............. .............. ........113.2.2 IEC 61850 Configuration ........... .............. ............. .............. ............ .............. ............. ............ .............. 123.2.3 IEC 61850 Client............ ............ .............. ............. .............. ............ .............. ............. ............ .............. 14
3.3 E-TERRACONTROL V3.4............................................................................................................................15
3.3.1 Scada Server Datasets and Dataitems...............................................................................................153.3.1.1 Description for each datasets:.......................................................................................................................163.3.1.2 Description for each data items: ...................................................................................................................17
3.3.2 Scada server Electric view.................................................................................................................183.3.3 E-terraBrowser.... ............. ............. .............. ............. ............ .............. ............. .............. ............ ........... 19
3.3.3.1 Analog Measurement I .................................................................................................................................193.3.3.2 Circuit Breaker POS.....................................................................................................................................193.3.3.3 Circuit Breaker Control (Open/Close)..........................................................................................................20
3.3.4 C264 configuration with PACiS SCE V4.33.........................................................................................21
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
5/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 5 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
FIGURES
Figure 1 : Installation SISCO MMS driver software................................................................ 9
Figure 2 : General architecture.............................................................................................11
Figure 3 : IEC61850 Configuration Server(s) tab..................................................................12
Figure 4 : IEC61850 Configuration Model Download tab ......................................................13
Figure 5 : IEC61850 Configuration Settings..........................................................................13
Figure 6 : IEC 61850 Client ..................................................................................................14
Figure 7 : SCADA Datasets C264 ........................................................................................16
Figure 8 : Scada Database IEC61850ClientDS dataset........................................................16
Figure 9 : Scada Database Measurements...........................................................................17
Figure 10 : Scada Database Double Point Status.................................................................17
Figure 11 : Scada Database Single Point Status ..................................................................17
Figure 12: Scada Database Point control .............................................................................17
Figure 13 : Scada Electric view ............................................................................................18
Figure 14 : Webfgviewer Analog measurement................................................. ...................19
Figure 15 : Webfgviewer Circuit Breaker position .................................................................19
Figure 16 : Popup dialog Trip / Close ...................................................................................20
Figure 17 : Electrical topology from PACiS SCE...................................................................21
Figure 18 : Electrical topology from E-terraSCADA..............................................................21
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
6/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 6 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
1. INTRODUCTION
1.1 DOCUMENT OBJECTIVE
This document specifies the installations and configurations required allowingcorrect link between a C264 and E-terraControlsystem.
The scope of this integration guide is to provide guidance to projects on approaches
to integrating E-terraControl V3.4 and PACiS system V4.2.1.
1.2 Who Should Use This Document
The audience for this document is as follows:
Systems integrators/engineers who are responsible for installing and configuringE-terraControlsystem with a C264 computer.
1.3 Operating System Support
E-terraControl is certified on Windows Server 2003 and supported on Windows XP.
The Windows XP platforms had Service Pack 1 and Service Pack 2 applied,generally with the latest Microsoft critical updates.
1.4 REFERENCE DOCUMENTS
Display Builder 5.5 Beta Release Notes.
E-terraControl 3.4 Beta Release Notes.
PACiS_Release Note_V4.2 Issue B.doc
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
7/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 7 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
1.5 ABBREVIATIONSBI : Bus InterfaceCRA : Change Request AnalysisCT/VT : Current Transformer/Voltage TransformerDB : DatabaseDE : Direct ExecuteDP : Double PointFR : Fault ReportFSS : Force Suppress SubstituteGPS : Global positioning SystemIED : Intelligent Electronic DeviceI/O : Input/output
LBUS : Legacy BusOI : Operator InterfaceOWS : Operator WorkStationPC : Personal ComputerRCP : Remote Control PointSBO : Select Before OperateSCE : System Configuration EditorSMT : System Management ToolSP : Single PointTBC : To Be CompletedTI : Telecontrol interfaceTPI : Tap Position IndicationXML : Extensible Markup Language
SCADA : Supervisory Control and Data Acquisition
1.6 Compatibility
EterraControl PACIS V4.2.1CMT SMT SCE Agency OI SCADA 2000
V3.4 V4.33A E12 J.01.04 4.37.F V3.22A G.00.30 M4-RC37
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
8/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 8 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
2. INSTALLATION
2.1 E-terraControl v3.4
E-terrabrowser should be installed prior to E-terracontrol in order to guarantee thatthe shortcuts are properly created.
If there is a problem with WebFG Viewer shortcut -- please run "Create WebFG
ViewerShortcut" from the 'E-terraControl\samples\Fix WebFG' start menu.
If there is a problem with WebFG Viewer configuration -- please run "Fix WebFGViewer Configuration" from the E_terracontrol\samples\Fix WebFG' start menu.
2.2 PACiS Communications Agency V3.22a
Kit packaged with E-terracontrol v3.4, in the \areva\e_terracontrol\bin directorycorresponds to PACiS Communications Agency V3.18. Do not install this version.Agency V3.22a has to be installed.
The IEC61850 Communications Agency is used by the IEC61850Config andIEC61850Client applications. This section describes installation and configuration ofthe Communications Agency and MMS driver infrastructure.
2.2.1 Installing the communications Agency
The Communications Agency may need to be installed separately. The betainstallation kit provides the communications agency installation kit within theSMP\bin directory.
- Run Agency_3.22a.exe this will install the IEC61850 Communications Agencysoftware in a folder named PACiS. Install it in disk:\areva\pacis folder using the
same disk as the e-terracontrol and follow the instructions, accepting the defaultvalues.
2.2.2 Installing SISCO MMS driver software
The IEC61850 Communications Agency application requires installation of a SISCOprovided OSI device driver.
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
9/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 9 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
Follow the following steps to install the OSI LLC Protocol Driver :
1. Select Start Settings Control Panel Network and Dial-upConnection, then double click the Local Area Connection; click the Propertiesbutton, then the Install button. Select the network component type of Protocol andclick the Add button.
3. From the Select Network Protocol Dialog Box, click the Have Disk... button.
4. From the Insert Disk Dialog Box, select the location of the osillc.inf file and clickon OK to accept the path. The .inf file was installed with the agency in the followinglocation [installation folder]\UCA2Agency\osillc\win2000 (or \winxp).
5. From the Select Network Protocol Dialog Box, click on OK. Click the Close buttonand restart your computer.
Figure 1 : Installation SISCO MMS driver software
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
10/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 10 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
2.2.3 IEC61850 Client needs Anonymous RPCs with Service Pack 2
After installing Windows XP Service Pack 2, a previously working IEC61850Clientmay not be able to form a connection to the IEC61850 Communications Agency.
In this case, the IEC61850Client.log file will report that the Open Session call failed.This failure is because, by default, XP SP2 restricts the use of Remote ProcedureCalls (RPCs).
You can force RPC to exhibit the same behaviour as earlier versions of Windows bysetting the registry key to RPC_RESTRICT_REMOTE_CLIENT_NONE (0).
HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\WindowsNT\RPC\Restric
tRemoteClients
Value Set to 0
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
11/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 11 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
3. CONFIGURATION
3.1 Purpose
C264_1
IEC61850 Configuration IEC61850 Client E-terraControl database SCADA
E-terraControl Webfg Viewer
OI E-terraControl
PACiS SCE
IEC61850 Agency
export SCE conf
C264_1
IEC61850 Configuration IEC61850 Client E-terraControl database SCADA
E-terraControl Webfg Viewer
OI E-terraControl
PACiS SCE
IEC61850 Agency
export SCE conf
Figure 2 : General architecture
3.2 IEC 61850
3.2.1 Agency application
The IEC61850Client applications will automatically start and stop the Agencyapplication as needed. When running, the Agency application will place a small iconon the lower right of the machine's console. Double clicking on this icon will causethe agency log to be displayed. A hard copy of the agency log is also created in thedirectory where the agency executable resides(drive:\areva\pacis\UCA2agency\agency.log).
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
12/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 12 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
3.2.2 IEC 61850 Configuration
Before using IEC61850Client to communicate with a new device, the device's modelmust be obtained using the IEC61850Config application.
IEC61850 Server(s) tab
All server connected to the IEC61850 Client must be define in the IEC61850 Servertab. For each server you must define the name and the IP Address of the server. Allinformation entered are automatically updated in the lean.cfg and agency.cfg file.Server name is equal to the ARName define in the IEC61850Device Data set in theconfiguration of scada device.
Figure 3 : IEC61850 Configuration Server(s) tab
Model Download tab
By default, the obtained XML file will go into a new IEC61850WORKsub-folder of
the E-terracontrolinstallation location. The integrator will not be able to override thislocation if desired.
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
13/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 13 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
Figure 4 : IEC61850 Configuration Model Download tab
Settings
After the model is obtained, a batch file could be launch directly. The batch file pathmust be selected with the menu -> File -> Settings. The batch file can be foundIEC61850Work folder.
Figure 5 : IEC61850 Configuration Settings
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
14/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 14 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
3.2.3 IEC 61850 Client
The E-terracontrol IEC61850 application provides E-terracontrolwith an interface toIEC61850 compliant devices. The IEC61850 Client applications use the PACiSAgency application to communicate with the IEC61850 devices.
The SCADA database objects that are required by the IEC61850 Client applicationinclude:
A hierarchical collection of Data Sets that model the IEC61850 Client'scommunication subsystem and IEC61850 device model (from the IEC61850Client itself to the IEC61850 bricks).
The measurement definitions and values associated to the Data Sets underthe form of Data Item collections.
Figure 6 : IEC 61850 Client
On the left is a tree display of the IEC61850 devices modeled in the E-terracontrolSCADA Server (database). It displays the remote device and the bricks modeledunder it.
On the right are details of any item selected in the tree. Current data value, quality,and timestamps are displayed in the details.
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
15/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 15 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
3.3 E-terraControl V3.4
3.3.1 Scada Server Datasets and Dataitems
SCADA datasets will be modeled in the SCADA database to define the followinginformation to SCADA and the IEC61850Client application.
IEC61850 client application information
IEC61850 device information (name and MMS ARName)
IEC61850 device logical devices and bricks to map into SCADA
In addition, a SCADA data source for the IEC61850Client application (type: device)needs to be modeled. The SCADA data source will reference a Dataset defining theIEC61850Client application. This is similar to CfeReader modeling.
The following SCADA dataset types need to be added to the E-terracontroldatabase to support this.
IEC61850ClientDS: This SCADA dataset type will be assigned to the
IEC61850Client Dataset.
IEC61850DeviceDS: This SCADA dataset type will be assigned to theIEC61850 device datasets.
IEC61850LogicalDeviceDS: This SCADA dataset type will be assigned to theIEC61850 logical device datasets.
IEC61850BrickDS: This SCADA dataset type will be assigned to theIEC61850 brick datasets.
IEC61850ControlDS: This SCADA dataset type will be assigned to theIEC61850 brick control datasets. This is used to model setpoints,
Raise/Lower and control data items.
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
16/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 16 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
3.3.1.1 Description for each datasets:
IEC61850ClientDS IEC61850ClientDS
AgencyHeartBeat = 3000NumMissedHeartbeats = 3HeartbeatMonitor_Freq = 5000ScanRate=5
C264 IEC61850DeviceDS
ARName = C264
CONTROL IEC61850LogicalDeviceDS
YPTR1 IEC61850BrickDS
XCBR1/2 IEC61850BrickDS
Figure 7 : SCADA Datasets C264
XCBR1/2Ctrl IEC61850ControlDS
Figure 8 : Scada Database IEC61850ClientDS dataset
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
17/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 17 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
3.3.1.2 Description for each data items:
Measurements YPTR : MX$val_1$mag$f
Figure 9 : Scada Database Measurements
Single and Double Point Status XCBR : ST$val_1$stVal
Figure 10 : Scada Database Double Point Status
Figure 11 : Scada Database Single Point Status
Single Point Control XCBRCtrl: CO$val_1$open / CO$val_1$close
Figure 12: Scada Database Point control
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
18/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 18 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
3.3.2 Scada server Electric view
SCADA equipments will be modeled in the SCADA database. Above, dataitems areassigned to equipments link and following equipments are assigned to Webfgviewer.
Stations Stations Root
Lattes Substation
CB1 Circuit breaker
CBPOS Status
CLOSE TRIP
INC1
Figure 13 : Scada Electric view
I1 Analog
Webfgviewer link
Webfgviewer link
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
19/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 19 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
3.3.3 E-terraBrowser
3.3.3.1 Analog Measurement I
The picture below shows the partial composite key definition needed to complete thebinding of the picture representing a measurement I2.
Figure 14 : Webfgviewer Analog measurement
3.3.3.2 Circuit Breaker POS
The picture below shows the partial composite key definition needed to complete thebinding of the picture representing a breaker with two switches.
Figure 15 : Webfgviewer Circuit Breaker position
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
20/21
AREVA PACIS Identification Number: 2059660E-terraControlV3.4 & PACIS V4.2_AInstallation & Configuration Guide - Issue A 17/11/06 Page: 20 / 21
CONFIDENTIAL
.Allrig
htsreserve
d.
AREVA
.Pass
ingona
ndcopy
ingo
fthisdocumen
t,usean
dcommun
ica
tiono
fitscon
ten
tsareno
tperm
ittedw
ithou
tpriorwri
tten
3.3.3.3 Circuit Breaker Control (Open/Close)
E-terrabrowser allows a tool tip to be associated with any visible object on a display.
The picture below shows the popup dialog witch allow sending a command to thecircuit breaker.
Trip (binding)
Command :MAIL/USER=control_%disapp%_%disfam%TRIP
Figure 16 : Popup dialog Trip / Close
Close (binding)
Command :MAIL/USER=control_%disapp%_%disfam%CLOSE
8/10/2019 E-terraControl V3.4 & PACIS V4.2_A
21/21