Upload
vankhue
View
224
Download
0
Embed Size (px)
Citation preview
Effect of partial needle lift over Diesel Spray Development and combustionand combustion
Raul PayriRaul PayriCMT Motores Termicos, Universitat Politecnica de Valencia
Collaborators:Collaborators:Jaime Gimeno, Michele Bardi, Juan Pablo Viera, Jose Enrique del Rey
1/40Brunel 2013
INDEX• Direct acting injector
• Hydraulic characterization• Mass flow rate measurements
• Spray momentum flux measurements
• Liquid phase visualization• Experimental methodology
• Results
• Analysis
• Vapor phase visualization• Experimental methodology
• Results
• Combustion results
2/40Brunel 2013
• Conclusions
The injection system
• A direct acting injector has been employed Di t dl lift t l i bl d Direct needle lift control is enabled
Piezo stack
Direct actingCommon-rail high
pressure pump
3/40Brunel 2013
The injection system• The injector allows the control of the needle position as a
function of the charge applied to the piezo-stack
Needle lift = f(charge)
• Main characteristics of the nozzle
Injector featuresBrand ContinentalNozzle seat type micro-sac
Injector features
Nozzle seat type micro sacN orifice 7Spray Angle 158 ºOutlet diameter 0.156 mmK factor 1.5Discharge coefficient 0 81
4/40Brunel 2013
Discharge coefficient 0.81
IR – Test conditions Four injection pressures (30, 90, 150 and 200 MPa) Back pressure is kept at 5 MPa Long energizing time (ET) = 3200µs Long energizing time (ET) = 3200µs 6 different lifts, more information SAE 2011-01-1827
Zone studied
5/40Brunel 2013
IR measurements
Linear trendHIGH CHARGE
LOW CHARGENeedle lift varies with the pressure
LOW CHARGE
It is possible to see a linear behavior of mass flow rate with the It is possible to see a linear behavior of mass flow rate with the pressure drop for larger needle lifts (throttling effect on the needle seat)
At low charge the needle position does not vary only with the charge applied to the piezo-stack injector but also with the pressure possibly due to elastic deformations
6/40Brunel 2013
pressure, possibly due to elastic deformations
Mass flow vs %Charge
Mass flow tends to converge to a constant constant (infinity needle lift)
The max mass flow rate for each injection pressure tends toconverge to a constant value after the max. % of charge is applied
7/40Brunel 2013
Spray momentum measures
Similar trend as in IR measurements
A similar trend as in mass flow rate results
Similar trend as in IR measurements
Again, the influence of needle lift as a function of charge and pressure is clearly observed
8/40Brunel 2013
g p y
INDEX• Direct acting injector
• Hydraulic characterization• Mass flow rate measurements
• Spray momentum flux measurements
• Liquid phase visualization• Experimental methodology
• Results
• Analysis
• Vapor phase visualization• Experimental methodology
• Results
• Combustion results
9/40Brunel 2013
• Conclusions
The test rig
• A novel high temperature – high pressure test rig was employed to study liquid phase penetration in real Diesel engine thermodynamic condition
Chamber diameter: 200 mm
View of the injector from lateral optical access
View of the injector fromfrontal optical access
Window diameter: 128 mm
M bi t t t 1000 KMax ambient temperature: 1000 K
Max ambient pressure: 15 Mpa Global view of the testing section withti l
10/40Brunel 2013
Continuous gas flow through the chamber optical accesses
Liquid determination set-up
• Mie scattering technique to detect liquid phase spray
Camera: Phantom V12
Lens: Nikkor 50 mm – f/1.8
Shutter time: 3 µs
Frame rate: 20 kfpsFrame rate: 20 kfps
pix/mm: 7.1
Field of view: ~70 x 70 mm
Repetitions: 6
Light source: Xe-arc, (double)
11/40Brunel 2013
Processing method• Image sectorization: each spray sector is analyzed separately
• Background correction by subtractionBackground correction by subtraction
• 3% threshold of the dynamic range for threshold calculation (SAE 980809)
12/40Brunel 2013
Processing method• Moving polynomial average to
avoid experimental noise•The injection event has been divided in The injection event has been divided in time step of 10s
•For each time step ti a time window of For each time step ti a time window of ±150 s has been evaluated
•A linear fit of the experimental data present ym
p pin the time window has been performed
•The value yi of the fitted curve in ti has
LLm
(θm)been calculated (θm)
ti• Parametrization of the curve on
two parameters (LLm and θm)
13/40Brunel 2013
150 µs
Test planDiff t i j ti t t t d t th l ith diff t dl lift• Different injection parameters were tested together along with different needle lifts
• The different charge levels are referred to in a quantitative way (low/med/high)
• The test plan is the same for liquid and vapor phase visualization experimentsp q p p p
• More details liquid penetration (Study liquid length penetration results obtained with a direct acting piezo electric injector, Applied Energy , 2013, 106, 152 - 162)
• More details Vapor penetration (Needle lift profile influence on the vapor phase penetration for aMore details Vapor penetration (Needle lift profile influence on the vapor phase penetration for a prototype diesel direct acting piezoelectric injector , Fuel, 2013, 113, 257 - 265 )
Fuel Commercial Diesel
Energizing time 3200 µs
Injector coolant temperature 343 K
Ambient gas Nitrogen
Gas pressure 5 Mpa
Gas temperature 870 – 950 K
Injection pressure 60 – 150 Mpa
Pi t k h l d hi h
14/40Brunel 2013
Piezo stack charge low – med – high
LL Results (1/4) Effect of temperature and injection pressure
Pinj = 150 MPa. Ch% = high Tamb = 950K, Ch% = high
15/40Brunel 2013
LL Results (2/4) Effect of ambient temperature and injection pressure on LLm
• Liquid length follows the general Liquid length follows the general trends described in literature• Higher LL at lower
temperaturetemperature• Small effect of injection
pressure on LL (higher LL for high injection pressurehigh injection pressure
• An important effect of piezo stack charge level is noticed. Longer liquid length at high charge
16/40Brunel 2013
LL Results (4/4)Piezo stack charge was quantified with parameter
m
observed at different Prail
highChm
LLm observed at different Prail
Linear increase of LL with Lambda
LLm
decreases at higher charge and might bem decreases at higher charge and might be related with LL variations
m
17/40Brunel 2013
Discussion• From Pastor et al. (Fuel 87 pp2871-2885, 2008)
Ca: area coefficient
a
faop
C
CDKLL
tan
2 Do: orifice diameterρf: fuel densityρa: ambient densitya
mvC
2
tan ρa: ambient densityCmv: dependent on thermodynamic equilibrium between fuel and ambient gas
When needle lift is modified the parameters changing in the equation are only Ca (area coefficient) and (spray angle)only Ca (area coefficient) and (spray angle)
This theoretical equation was used to understand if variations in spray
opening angle and Ca can justify LL dependence to the charge level found experimentally
18/40Brunel 2013
Discussion• For each Tamb – Prail combination the high charge LL was used as
reference
• The experimental (continuous line) variations in LL were compared with the ones predicted (dashed line) by the equation using Ca and m
19/40Brunel 2013
INDEX• Direct acting injector
• Hydraulic characterization• Mass flow rate measurements
• Spray momentum flux measurements
• Liquid phase visualization• Experimental methodology
• Results
• Analysis
• Vapor phase visualization• Experimental methodology
• Results
• Combustion results
20/40Brunel 2013
• Conclusions
S hli i li ti t
Experimental methodologySchlieren visualization setup
21/40Brunel 2013
Sample videoShape = bootPrail = 150 MpaBp = 5 MpaBp 5 MpaT = 870 K
Frame rate = 14 834 fpsFrame rate = 14.834 fpsTime Step = 67 μsShutter time = 10 μs
10 mm
22/40Brunel 2013
Processing method
Each spray contour is processed separately for each time step and each sectortime step and each sector
Spray penetration (S) is calculated as the distancecalculated as the distance between the outlet orifice and the furthest point detected in the spray boundaryp y y
The spreading angle is calculated by interpolating two lines in the spray boundary, between 25% and 60% of the spray penetration, and forcing these interpolations to go through the outlet orifice
23/40Brunel 2013
Temperature effect
Vapor penetrationLiquid length
24/40Brunel 2013
Injection Pressure effect
Vapor penetrationLiquid length
25/40Brunel 2013
Charge effect (1/3)
Vapor penetrationVapor penetrationLiquid length
26/40Brunel 2013
Charge effect (2/3)
Vapor penetrationVapor penetrationLiquid length
27/40Brunel 2013
Charge effect (3/3)
28/40Brunel 2013
Charge effect (4/4)
29/40Brunel 2013
INDEX• Direct acting injector
• Hydraulic characterization• Mass flow rate measurements
• Spray momentum flux measurements
• Liquid phase visualization• Experimental methodology
• Results
• Analysis
• Vapor phase visualization• Experimental methodology
• Results
• Combustion results
30/40Brunel 2013
• Conclusions
Experimental methodologyCH*/OH* chemiluminescence imaging setup for ignition characterization
31/40Brunel 2013
CH*/OH* Raw images
32/40Brunel 2013
Experimental methodology Each spray is processed separately The maximum for each radial position is obtained
A i i fil i b i d i h An average intensity profile is obtained averaging the repetitions and the different sprays
33/40Brunel 2013
Experimental methodology The average intensity profile obtained from each time step is
condensed in a 3-axes contour map
In only one plot the timing, the location and the intensity of the radiation are presented
34/40Brunel 2013
Results (1/3) CH* location is strongly related to spray tip penetration
Oxygen concentration has a strong effect on OH* (but not on CH* )CH* OH*
35/40Brunel 2013
Results (2/3)
First and second stage ignition delay (SoCH and SoOH) have been measured under a wide range of test conditions
The observation of SoCH/SoOH dwell time confirms that SoCH is strictly linked with the fuel air/mixing and the thermodynamics of the mixture
The SoOH is also affected by the chemistry of the mixture (O2%)
36/40Brunel 2013
Results (3/3)
The second stage ignition timing (SoOH) has been compared for different injection typologies
The effect of injection pressure/needle
injection typologies
lift on ignition delay is very low
However an opposit trend can be observed when the mass flow rate is reduced either reducing the injection
th dl liftpressure or the needle lift
Thi it t d i b bl l t d This opposite trend is probably related to the increment in spreading angle related to the partial needle lift commented before
37/40Brunel 2013
commented before
INDEX• Direct acting injector
• Hydraulic characterization• Mass flow rate measurements
• Spray momentum flux measurements
• Liquid phase visualization• Experimental methodology
• Results
• Analysis
• Vapor phase visualization• Experimental methodology
• Results
• Combustion results
38/40Brunel 2013
• Conclusions
Conclusions (1/2)• Results show the effect of needle partial lift over injected mass flow
and spray momentum flux
• For large lifts the pressure drop occurs mainly in the hole while for small lifts the pressure drop occurs mainly in the needle seat
• The experimental results presented for the liquid penetration are consistent with what is found in the literature for the influence of Tamb and Pinj.
• An interesting relationship was found between steady liquid length (LLm) and charge level (needle lift)g ( )
• Possible causes for relationship between LL and needle lift: The local increase in velocity caused by the partial needle lift can change The local increase in velocity caused by the partial needle lift can changenon-axial component of the fuel velocity at the orifice outlet Increase in fuel temperature due to friction in the nozzle seat O t f it ti i th dl t
39/40Brunel 2013
Onset of cavitation in the needle seat
Conclusions (2/2)
• Gas temperature seems not to have an important effect on vaporpenetration (being the backpressure the same, changes in densityare very small) or spreading angle
• Partial needle lift allow to control also the vapor penetration (similarly• Partial needle lift allow to control also the vapor penetration (similarlyto injection pressure). The results also confirmed the effect of needlelift over spreading angle obtained in LL measurements.
• As the mass flow rate shows to be closely related to the spraypenetration rate the needle lift control-ability is a very powerful toolpenetration rate, the needle lift control ability is a very powerful toolto control the injection event as desired
• The modifications in the spray development are reflected in also in the combustion, showing a (slight) reduction in the ignition delay at reduced needle lift
40/40Brunel 2013