1 of 9

Users Manual

Bluetooth GPS Receiver

2 of 9

Introduction eGPS-6500 is the new generation of the smallest compact Bluetooth GPS receiver from eGPS-6500 simply turns a Bluetooth-enabled computing device into the wireless navigation system with most GPS-enabled navigation software selling in the market. With new skytraq chipset and high sensitive GPS antenna, eGPS-6500 will surely lead you to experience the highest GPS reception performance and the remarkable GPS accuracy. The eGPS-6500 is well suited to system integrations including PDA, Smart phone, Tablet PC and Notebook PC with Bluetooth devices. It satisfies a wide variety of applications that are purposes in automotive and outdoor recreation navigation system.

General Features : High Performance Skytraq Chipset Real Wireless Navigation : leading to the real navigation world High Sensitivity & Fast Fix : Excellent GPS reception and fast GPS (TTFF) Time The Smallest Compact Size & Light Weight WASS/EGNOS support Low Power Consumption Workable convenient replaceable & rechargeable Li-ion battery Easy-to-Use Three LED Light

Indicating Bluetooth life connection, GPS and battery status Excellent Compatibility

Workable with almost Bluetooth enabled PDA or computing devices, and most GPS enabled mapping S/W

Specifications :

Receiver Type L1 Frequency, C/A Code 65 Channels GPS Correlator 8192 Search Bins with GPS Acquisition Accelerator

- Update Rate 1 Hz

- Accuracy 2.5m CEP(Stand-Alone, S/A off)

- Acquisition Cold Start: 29Sec (Typical) Warm Start: 25 Sec (Typical) Hot Start:

3 of 9

Reacquisition:

4 of 9

NO NAME LED FUNCTION

1 Battery Status LED RED

ON : During charging battery with connection to a power charger OFF : Once battery is fully charging. BLINKING : Low power Power on/off switch

2 GPS Status LED Green ON : Current position fixed BLINKING : During GPS signal reception OFF : Waiting for GPS signal reception

3 Bluetooth Status LED

BLUE

ON : Bluetooth connection is on and ready for data transmission. BLINKING : No Bluetooth connection yet. Searching Bluetooth connection

4 Power Jack Connect a power charger to the power jack to recharge the internal battery

5 Battery Rechargeable and replaceable Lithium-in Battery

6 Battery Cover Battery cover

Battery Warning To prevent any accidents, which might be caused with rechargeable battery at high temperature, please do not leave alone the BT GPS for long time at a vehicle when it is not used. Do not expose the internal battery to high temperature over over 140F (50C) Do not disassemble the battery.

Activating Bluetooth on your PDA or PC Before activating the Bluetooth function on your PDA/PC, please switch on the BT GPS

Receiver for pairing and check that your device is equipped with Bluetooth. NOTE : The pairing procedure is only required the first time you use this device. 1 Activate the Bluetooth pop-up menu, turn on the Bluetooth function and select BT Manager. 2 Click Connect to establish a new connection.

5 of 9

3 Select Explore a Bluetooth device, then turn on the eGPS-6500 power before going on to

the next step. 4 Select Device, then click Next.

6 of 9

5 Choose and click on BT GPS. 6 Enter password 0000, and press Enter.

7 Select SPP slave, then click Next.

7 of 9

8 Click Finish and your eGPS-6500 connection should be established successfully.

9 Click the Bluetooth icon again, and select Bluetooth Settings. 10 In the Serial port window, click Enable service, then set the outbound COM port to

8.

8 of 9

Software Setup E-Map Software PAPAGO5 1 Activate your PaPaGo Software 2 Click Tools and select Option.

3 Click GPS, and setup as described below. 4 Return to the main screen, clicks tools and select GPS to open the GPS status window. 5 GPS position is fixed and navigation begins.

9 of 9

Turn off your PDA or PC Switch off the Bluetooth function before you turn off your PDA/PC, and Switch off .Receiver will disconnect the GPS function. If the eGPS-6500 is in AUTO mode, you do not need to take additional action.

How to test your Bluetooth GPS Receiver The testing program only supports the Microsoft Windows CE & Pocket PC based PDA platform. Run the GPS View to execute the installation procedure of testing program (via PC and

ActiveSync). Run the GPS Information program from Start Program files of PDA. Here is the description of GPS Information testing program User must select COM port, Baud Rate (9600) and click theStar GPSbutton to start receiving GPS data. NoteThe Bluetooth device in most of the applications have an auto-detect feature that

you do not need to select the Baud Rate. FCC Notices This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause

undesired operation. FCC RF Exposure Requirements This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. NOTETHE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV

INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT.