Upload
boothu1
View
145
Download
3
Tags:
Embed Size (px)
Citation preview
www.CareerSafeOnline.com
Electrical Safety
www.CareerSafeOnline.com
Electricity is an important part of our modern world and sometimes it is easy to forget just how dangerous it can be.
Given the correct circumstances, electricity can cause serious injuries or even death.
Electrical Safety
www.CareerSafeOnline.com
• Electrocution is the cause of 12% of all workplace deaths among young workers.
• Electrocution is the third leading cause of work-related deaths among 16 and 17-year-olds.
Electrical Safety
www.CareerSafeOnline.com
The most common types of electrical injuries are:
• Electrical shock
• Electrocution (death due to
electrical shock)
• Burns
• Falls
Electrical Injuries
www.CareerSafeOnline.com
Touching a live wire and an electrical ground will cause a shock.
Electrical Shock
www.CareerSafeOnline.com
Touching two live wires of different voltages will cause electrical shock.
Electrical Shock
www.CareerSafeOnline.com
The severity of the shock depends on:
• Path of the current through your body
• Amount of current flowing
through your body
• Length of time your body is in contact with the circuit
Electrical Shock
LOW VOLTAGE DOES NOT MEAN LOW HAZARD
www.CareerSafeOnline.com
Burns are the most common injury caused by electricity. The three types of burns are:
Burns
• Electrical burns• Arc burns• Thermal contact burns
Electrical burns can occur when you come into direct contact with electricity.
www.CareerSafeOnline.com
An arc occurs when there is a gap between conductors and current travels through the air.
Burns
•Electrical burns•Arc burns•Thermal contact
burns
www.CareerSafeOnline.com
Thermal contact burns can occur when electricity ignites combustible material.
• Electrical burns
• Arc burns
• Thermal contact burns
Burns
www.CareerSafeOnline.com
Another common type of electrical injury is falling.
Workers who experience a shock on elevated work surfaces such as platforms, ladders or scaffolds can fall resulting in serious injury or death.
Falls
www.CareerSafeOnline.com
To avoid injuries, you should be aware of electrical hazards. Some of the most common electrical hazards are: • Exposed electrical parts
• Overloaded circuits
• Defective insulation
• Improper grounding
• Damaged power tools
• Overhead power lines
• Wet conditions
Electrical Hazards
Let’s take a closer look at each of these hazards.
www.CareerSafeOnline.com
Exposed electrical parts can include:
• Breaker boxes without a cover
• Electrical terminals in motors, appliances, and electronic equipment
Exposed Electrical Parts
www.CareerSafeOnline.com
Overloading a circuit increases the potential for
fires to occur. Overload hazards exist if:
• Too many devices are plugged into a circuit
• The wire insulation melts
• An improper overcurrent protection device is used
• No overcurrent protection device is used
Overloaded Circuits
www.CareerSafeOnline.com
Overcurrent protection devices include:
• Circuit breakers
Overloaded Circuits
• Fuses • Ground fault circuit
interrupters (GFCI)
A circuit breaker automatically “trips” and shuts off the current in a circuit if it becomes overloaded.
www.CareerSafeOnline.com
A fuse contains an internal part that melts and shuts off the current if there is an overload.
• Circuit breakers
• Fuses
Overloaded Circuits
• Ground fault circuit interrupters
www.CareerSafeOnline.com
A ground fault circuit interrupter (GFCI) detects current leaking from a circuit to ground and shuts the current off.
• Circuit breakers
• Fuses
• Ground fault circuit interrupters
Overloaded Circuits
Receptacle type
www.CareerSafeOnline.com
Defective Insulation
To protect you, electrical wires are insulated by a plastic or rubber covering. Insulation prevents conductors from coming in contact with each other and with people.
Make sure the insulation of tools and cords you are using is not damaged.
www.CareerSafeOnline.com
Grounding
When an electrical system is properly grounded, there is a path that allows the current to travel to the earth (the ground).
When any electrical system isnot properly grounded, a hazardexists.
www.CareerSafeOnline.com
Power tools that are damaged or not properly maintained can cause you to be seriously injured.
If you touch a metallic part of a power tool that is energized because of damaged insulation or improper grounding, you could be shocked.
Power Tools
www.CareerSafeOnline.com
Power Tools
To protect you from shock,burns and electrocution,
toolsmust:
• Have a three-wire cord with
ground and be plugged into a grounded receptacle.
• Be double insulated.
• Be powered by a low-voltage
isolation transformer.
www.CareerSafeOnline.com
Overhead Power Lines
Overhead power lines are not usually insulated, and cause more than half of all electrocutions.
www.CareerSafeOnline.com
Wet Conditions
Wet conditions are hazardous because you can become an easy path for electrical current.
There are many circumstances that create wet conditions:
• Standing in water• Wet clothing• High humidity• Perspiration
www.CareerSafeOnline.com
Safe Work Practices
• Inspect cords before each use• Never overload a circuit • Stay away from all unguarded conductors• To unplug, pull on the plug,
not the cord• Don’t wear jewelry or use
other metal objects around electrical equipment
You can StartSafe and StaySafe by usingthe following safe work practices:
www.CareerSafeOnline.com
Training concerning electricity is very important. Training for employees working with electrical equipment must include how to:
• De-energize the equipment
• Use lockout and tag procedures
• Use insulating protective equipment
• Maintain a safe distance from energized parts
• Use appropriate PPE
Safe Work Practices: Training
www.CareerSafeOnline.com
Safe Work Practices: Lockout/Tagout
• Turn off the power supply
• Put a lock on all power sources
to the circuit
• Apply a tag
• Test the circuit
When performing lockout/tagout on circuits, trained employees will do the following:
www.CareerSafeOnline.com
Summary
It is very important to StartSafe and StaySafe around electricity. In order to do so:
• Know the hazards• Plan your work and plan for safety• Avoid wet working conditions and
other dangers• Avoid overhead power lines• Use proper wiring and connectors• Use and maintain tools properly• Wear the correct PPE for the job