Elevator

‘Y’ Series Elevator

Operation and Maintenance Manual

Rev. 1 Date 28-Dec-09

‘Y’ Series Elevator Operation Procedure Manual

1

TABLE OF CONTENTS

Section Page

1 - Introduction 2

1.1 General Information 1.2 Description

2 - Operation 3-4

2.1 Installation 2.2 Operation

3 - Maintenance 5

3.1 Inspection 3.2 Lubricants

4 - Shop Repairs 6-7

4.1 Changing Inserts 4.2 Slip Insertion and Removal 4.3 Elevator Disassembly

Critical Drawing Areas 8 Assembly, Parts Breakdown and Replacement Parts 9-20 Certificate of Warranty and Guarantee to Quality 21


5

3. MAINTENANCE Practice safety at all times when servicing the equipment and use approved safety methods, material and tools. Always wear protective gear for eyes, head and hands.

3.1 INSPECTION To insure optimum performance from the “Y” series slip type elevators, the following checks should be performed once a week:

• Check for worn hinge pin, latch pin, latch lock pin, slips and slip pins and their mating parts. These may hinder proper opening and closing of the door, latch and latch lock.

• Check slip springs, rubber bushings, inserts and setting plate for wear. • Check for proper operation of latch stop mechanism. Latch should not stop against

the body when engaged. • Check slip setting ring for spreading and wear in the setting area. • Check to make sure that link block bolts are retained w/ nuts and cotter pins.

It is recommended that elevators undergo factory magnetic particle inspection a minimum of once every six months and load test once a year.

3.2 LUBRICANTS Lubricate the elevator regularly during the usage and storage to prevent corrosion. Use an extreme pressure, multi-purpose, lithium base grease of no. 1 or no. 2 consistency and light machine oil. Do not use pipe dope (anti-seize compound) for lubrication on the Y-Series Elevators. When the elevator is in use, lubricate the elevator according to the followingschedule:

Daily

• Grease hinge pins • Lubricate latch pin and latch lock pin • Grease underside of lifting arm • Grease seating face of slip setting ring • Grease back of slips • Make sure link bolts have nuts and cotter pins

Weekly

• Brush grease on springs • Grease link retainer fasteners


6

4. SHOP REPAIRS

4.1 CHANGING INSERTS Always wear eye protection when removing or replacing inserts to protect against chip fragments.

To replace worn inserts or change sizes:

• Remove guide plate, slip setting ring and bushing, and insert retainer plate. • Using a brass punch and hammer, drive out the inserts. • Clean and lubricate the insert slots with light machine oil before installing new inserts.

Important: Install the correct size inserts for the tubular used and make sure the teeth are pointing in the up position.

4.2 SLIP INSERTION AND REMOVAL To insert slip bodies into the elevator, use the following procedure:

1. Open the elevator fully and clean the slip taper and spring pockets. 2. Clean the slips if necessary and grease the taper portion of the slip body. 3. Insert the slip springs into the spring pocket leaving the inner edge of the spring exposed. 4. Starting on the left side of the elevator and proceeding counter clockwise, insert assembled

slip bodies into the elevator one at a time. Compress the edge of the lip spring with the bottom of the upper pocket.

5. For the LYT style elevator, insert the slip retaining pin, or for the HYC, HYT, YT, MYT, YC style elevators, insert the slip retaining bolt through the top of the elevator, slip body lug and into the slip spring. Do not insert the pin or bolt completely through the spring until both pins retain their respective slip body and slip spring.

6. Once both slip pins are in place, (LYT) insert the slip retaining pin into position, or (HYC, HYT, YT, MYT, YC) screw retaining bolts into place.

7. Place an insert retainer plate into each slip. 8. Place the slip setting ring over the slips on the left hand side of the elevator. Attach the setting

ring to the slip segments with rubber bushings, lock-washers and cap screws. (Note: the setting ring must be placed on the left side of the elevator to avoid obstructing the tubing entering the elevator).

9. Secure the insert retainer plates with the short cap screws on the right side of the elevator. 10. Tighten all cap screws. There must be approximately 1/16 inch play between the slip setting

ring and its corresponding insert retainer plate as provided by the bushing. (Important: each set of cap screws retaining the slip setting ring and insert retainer must be secured with lock wire to keep them from backing out. Stainless Steel 3/32” lock wire is recommended).

o To prevent jamming, check each pair of slip bodies for the following: � Free movement of slip body guide pin. � No interface of slip guide pin lug in spring recess slots. � A gap between the slips when they are set and fully compressed.

For slip removal, the top guide plate, slip setting ring, and slip retaining bolt must be removed from the elevator.


7

4.3 Elevator Disassembly

• (HYC, YT, YC, MYT, LYT) latch pins are retained by dowel pins that must be removed before driving out latch pin. Drive out latch pin from bottom of elevator.

• To remove the latch lock pin on (MYT, HYT, YT), remove dowel pins and drive out latch lock pin. For (YC, YT) remove cotter key and drive out the latch lock pin. On the HYC simply remove the cotter and nut.

• Hinge pins on the LYT, MYT, YT, YC, and HYC are pressed fit. To remove, simply drive the hinge pin out from the bottom of the elevator. The hinge and latch pin on the HYT elevator are retained by expansion plugs and lock bar. To remove, drive the pins out from the bottom of the elevator which will knockout the expansion plug and shearing lock bar.

• To remove the link block, remove cotter keys from the link block bolts and unscrew link block bolts.

• After inspecting all parts for cracks and wear, replace defected parts and reassemble in reverse order of disassembly.

Because HYC, YT, YC, MYT, and LYT hinge pins are pressed fit, they must be replaced with new ones once they are removed from the elevator. Failure to replace the original hinge pin once it is removed may cause it to walkout or fallout of the elevator during use and cause severe injury.

4.4 ACCESS OIL TOOLS, INC. FACTORY TOOL REPAIR. Worn elevators are returned to high quality condition with precision factory repair procedures. When tools are received for repairs, they are dismantled and checked for dimensional accuracy and undergo magnetic particle inspection. Worn areas are repaired by welding or replacing with new parts and the components are reheat-treated to original hardness specifications. After a second magnetic particle inspection, the tools are reassembled and carefully checked.

Caution • Do not use any elevator if the latch and latch lock do not function properly. • Use only parts manufactured and sold by Access Oil Tools, Inc. or authorized agents. • Re-machining and re-heat treating should be performed only at Access Oil Tools, Inc.

manufacturing facility or by an authorized repair agent. Improper machining could result in increased stress (decreased load carrying capability) or improper alignment of component parts. Either condition could be hazardous to personnel and equipment.

• Due to the complex metallurgy found in Access Oil Tools, Inc. materials, welding should be performed only at access oil tools, inc. manufacturing facility or by an authorized repair agent.

• Bodies and doors are specifically matched by trained Access Oil Tools, Inc. professionals. For this reason, a body or door from one elevator should never be exchanged with a body or door from another elevator.

• Pins retained by riveting or peen must be well secured by upsetting a substantial amount of material on the pin or mating parts.

• Always wear gloves and eye protection when grinding, striking or handling parts. • Do not use any elevator with wear in hinge pin, latch pin, and latch lock pin areas. Wear in

these areas will cause latch and latch lock to function improperly. • Make sure that cotter pins are used on link block bolts.


8

“Y” SERIES ELEVATOR CRITICAL AREAS

10

14

13

7

24

1223

20

6

15

213

22

25

4

11

19

9

8

16

17

18


AOT # Description Size of Links Wt

AOT # Description Wt (lbs.)

AOT 20 TON LYT SLIP TYPE ELEVATOR

LYT SLIP ASSEMBLIES

9

E28745-2

E28745-3

E28745-4

E28745-6

E28745-7

2-1/16” x 1” LYT Slip Assembly

2-1/16” x 1-1/4” LYT Slip Assembly



2-1-16” x 3/4” LYT Slip Assembly


AOT # Item No. Description No. Req. Wt. (lbs.)

AOT # Item No. Description No. Req.

No. Req.

Wt. (lbs.)

AOT # Item No. Description Wt. (lbs.)

LYT REPLACEMENT PARTS

INSERTS

LYT SETTING PLATES

10

E30644E30645E28757E28760

E28762

E28786E28785

E28767E28753

E28787

E28782

E28765

50512-C

51480-10

51604-14-C

E28766

51603-08-C

E32486

E28769

E28761

51408-1251603-08-C

LYT LatchLYT Elevator Latch LockLatch Pin LYT Elevator

Slip Bolt LYT Elevator

LYT Link BlockLYT Insert Retainer Plate

LYT Setting Plate BoltLatch Lock Pin LYT Elevator

Hinge Pin LYT Elevator

Insert Retainer Screw

LYT-20 2-1/16” x 2-1/16”

LYT Link Block Retainer

Nut, Hex Slotted 3/4 UNC, Steel ZN

1/8” x 1.25” Cotter Pin

Pin, Roll 1/4” x 2”, Steel ZN

1/4” x 1-1/2” LYT Dowel w/ Point

Pin, Roll 3/16” x 1”, Steel ZN

LYT Latch Spring

LYT Latch Lock Spring

LYT Slip Spring

.125” x 1-1/2” Cotter PinPin, Roll 3/16” x 1”, Steel ZN

3467

8

910

1112

13

14

15

16

17

18

19

20

21

22

23

2425

1114

2

42

11

2

1

4

4

4

1

1

1

1

1

4

41

3.701.70.44.32

.90

.13

.22

.23

.51

.12

2.33

.10

.02

.01

.04

.11

.03

.05

.11

.03

.02

.05

E28772E28775E28778E28749

E29370

2-1/16” & 2“ LYT Insert1-1/2” (1.900”) LYT Insert1-1/4” (1.660”) LYT Insert

1” (1.315”) LYT Insert

3/4” (1.050”) LYT Insert

8888

8

8888

8

E28782E28737E28783E28784

E28736

E28735

2-1/16” Setting Plate2“ Setting Plate1-1/2” (1.900”) Setting Plate1-1/4” (1.660”) Setting Plate

1” (1.315”) Setting Plate

3/4” (1.050”) Setting Plate

7777

7

7

1111

1

1

2.252.353.003.10

3.15

3.20

.25

.25

.25

.25

.25


11

AOT 40 TON MYT SLIP TYPE ELEVATOR


E29328 MYT Elevator Complete Less Slip Assembly 1-1/4” – 2-3/4” 148

MYT SLIP ASSEMBLIES


E29343-1 2-7/8” x 2-7/8” MYT Slip Assembly 44.00



E29343-4 2-7/8” x 2” MYT Slip Assembly 47.50

E29343-5 2-7/8” x 1-1/2” (1.900”) MYT Slip Assembly 48.75

E29343-6 2-7/8” x 1-1/4” (1.660”) MYT Slip Assembly 49.75

E29343-7 2-7/8” x 1” (1.315”) MYT Slip Assembly 49.75

E29343-8 2-7/8” x 3/4” (1.050”) MYT Slip Assembly 51.00

E29343-10-S 2-7/8” MYT Slip Segments Only (Matched Set of 4) 31.00


12

MYT REPLACEMENT PARTS


E29333 3 Hinge Pin 1 4.00

E30652 4 Latch 1 10.00

E29334 5 Latch Pin 1 4.00

E29338 6 Latch Spring 1 .50

E30653 7 Latch Lock 1 2.00

E29335 8 Latch Lock Pin 1 .50

E29349 9 Latch Lock Spring 1 .25

E30841 10 Latch Lock Door Pin 1 .50

E947128-120 11 Latch Pin Retainer 1 1.50

E947128-172 12 Latch Lock Pin Retainer 1 .50

E940308-1 13 Grease Fitting 1 .10

E30708 N/P Latch & Latch Lock Assembly 1 12.88

E29337 14 Link Block 2 1.00

E939009-65 16 Upper and Lower Link Block Bolts 4 .45

E939484-7 17 Link Block Nut 4 .20

E939672-18 18 Cotter Pin 4 .01

E29336 19 Slip Bolt 4 .75

E29340 20 Slip Spring 4 .25

E29347 21 Setting Ring Screw 2 .25

E939370-13 22 Setting Plate Washer 2 .06

E939098-15 23 Insert Retainer Screw 2 .13

E29344 25 Insert Retainer Plate 4 .50

INSERTS


E24773 24 2-7/8” x 2-7/8” Insert 8 .75

E29255 24 2-7/8” x 2-3/8” Insert 8 1.00

E29256 24 2-7/8” x 2-1/16” & 2” Insert 8 1.13

E29257 24 2-7/8” x 1-1/2” (1.900”) Insert 8 1.25

E29258 24 2-7/8” x 1-1/4” (1.660) Insert 8 1.38

E29259 24 2-7/8” x 1” (1.315”) Insert 8 1.44

E29259-1 24 2-7/8” x 3/4” (1.050”) Insert 8 1.50

RECOMMENDED SPARES INCLUDE 1 SET OF INSERTS FOR EACH PIPE SIZE TO BE RUN

MYT SETTING RINGS


E29348 28 2-7/8” MYT Setting Ring 6.50



E29351 28 2” MYT Setting Ring 7.10

E29352 28 1-1/2” (1.900) MYT Setting Ring 7.35

E29353 28 1-1/4” (1.660) MYT Setting Ring 7.50

E29354 28 1” (1.315”) MYT Setting Ring 7.90

E29354-1 28 3/4” (1.050”) MYT Setting Ring 8.05

RECOMMENDED SPARES INCLUDE 2 SETTING RINGS FOR EACH PIPE SIZE TO BE RUN


13

AOT 75 TON YT SLIP TYPE ELEVATOR


E23105 YT Elevator Less Slip Assembly 2-1/4” – 2-3/4” 355

YT SLIP ASSEBLIES


E23108-5 3-1/2” x 3-1/2” YT Slip Assembly 64.00 E23108-3 3-1/2” x 2-7/8” YT Slip Assembly 76.00 E23108-4 2-7/8” x 2-7/8” YT Slip Assembly 76.00 E23108-6 2-7/8” x 2-3/8” YT Slip Assembly 79.00 E23108-7 2-7/8” x 2-1/6” YT Slip Assembly 81.00 E23108-8 2-7/8” x 2” YT Slip Assembly 82.00 E23108-9 2-7/8” x 1-1/2” (1.900) YT Slip Assembly 83.50 E23108-10 2-7/8” x 1-1/4” (1.660) YT Slip Assembly 85.50 E23108-11 2-7/8” x 1” (1.315) YT Slip Assembly 86.50 E23108 3-1/2” YT Slip Segments Only (Matched Set of 4) 51.00

E23108-2 2-7/8” YT Slip Segments Only (Matched Set of 4) 51.00


14

YT REPLACEMENT PARTS


E23116-1 3 Hinge Pin 1 4.13 E15348 4 Latch 1 27.00 E24182 5 Latch Pin 1 5.00 E12978 6 Latch Spring 1 .63 E12946 7 Latch Cam 1 1.50 E12972 8 Latch Lock 1 3.50 E13530 9 Latch Lock Pin 1 .63 E12529 10 Door Lug Pin 1 .65 E29464 11 Latch Pin Retainer 1 .20 E940308-1 12 Grease Fitting 1 .05 E940308-8 13 Grease Fitting 1 .05 E9519 14 Link Block 2 5.50 P8B .875 x 3 15 Upper Link Block Bolt 2 1.00 P8B .75 x 3 16 Lower Link Block Bolt 2 1.00 PSN .75 17 3/4” Slotted Nut 2 .25 PC .156 x 1.5 18 Link Block Cotter Pin 4 .05 E23115 19 Slip Bolt 4 1.25 E23113 20 Slip Spring 4 .25 E23630 21 Guide Plate 1 4.00 E939098-75 22 Guide Plate Screw 2 .25 E939098-64 23 Guide Plate Lock washer 2 .15 E27697 24 Setting Plate Bolt 4 .25 E27532 25 Insert Retainer Screw 4 .06 E27546 26 Setting Ring Retainer (3-1/2”) 2 .13 E27507 26 Setting Ring Retainer (2-7/8”) 2 .13 E27696 27 Rubber Bushing 4 .06 E24507 28 Insert Spacer (3-1/2”) 8 .13 E24508 28 Insert Spacer (2-7/8”) 4 .25 PSN .875 29 7/8” Slotted Nut 2 .25 E27530 31 Insert Retainer (3-1/2”) 4 .13 E27541 31 Insert Retainer (2-7/8”) 4 .25

YT INSERTS


E24774 30 3-1/2” x 3-1/2” Insert 24 .50 E30358 30 3-1/2” x 2-7/8” Insert 24 .75 E24773 30 2-7/8” x 2-7/8” Insert 12 .75 E29255 30 2-7/8” x 2-3/8” Insert 12 .75 E29256 30 2-7/8” x 2-1/16” & 2” Insert 12 1.00 E29257 30 2-7/8” x 1-1/2” (1.900”) Insert 12 1.20 E29258 30 2-7/8” x 1-1/4” (1.660”) Insert 12 1.38 E29259 30 2-7/8” x 1” (1.315”) Insert 12 1.45


YT SETTING RINGS


E27813 33 3-1/2” YT Setting Ring 3.13 E27695 33 2-7/8” YT Setting Ring 3.56 E27694 33 2-3/8” YT Setting Ring 4.00 E27812 33 2-1/16” YT Setting Ring 4.25 E28821 33 2” YT Setting Ring 4.25 E27811 33 1-1/2” (1.900”) YT Setting Ring 4.31 E27810 33 1-1/4” (1.660”) YT Setting Ring 4.38 E29001 33 1” (1.315”) YT Setting Ring 4.75



15

AOT 75 TON YC SLIP TYPE ELEVATOR


E24140 YC Elevator Less Slip Assembly 3-1/2” – 7”

YC SLIP ASSEMBLIES


E24077-1 7” x 7” YC Slip Assembly

E24077-1 7” x 6-5/8” YC Slip Assembly

E24072-2 5-1/2” x 5-1/2” YC Slip Assembly

E24072-7 5-1/2” x 5” YC Slip Assembly

E24072-5 4-1/2” x 4-1/2” YC Slip Assembly

E26830 4-1/2” x 4” YC Slip Assembly

E34931 4-1/2” x 3-1/2” YC Slip Assembly

E24072-4 4-1/2” Slip Segment Only (Matched Set of 4)

E24072 5-1/2” Slip Segment Only (Matched Set of 4)

E24077 7” Slip Segment Only (Matched Set of 4)


16

YC REPLACEMENT PARTS AOT # Item No. Description No. Req. Wt. (lbs.) E24181 3 Hinge Pin 1 4.13 E15348 4 Latch 1 27.00 E24182 5 Latch Pin 1 5.00 E12978 6 Latch Spring 1 .63 E12946 7 Latch Cam 1 1.50 E12972 8 Latch Lock 1 3.50 E13530 9 Latch Lock Pin 1 .63 E12529 10 Door Lug Pin 1 .65 E29464 11 Latch Pin Retainer 1 .20 E940308-1 12 Grease Fitting 1 .05 E940308-8 13 Grease Fitting 1 .05 E9519 14 Link Block 2 5.50 P8B .875 x 3 15 Upper Link Block Bolt 2 .50 P8B .75 x 3 16 Lower Link Block Bolt 2 .50 PSN .75 17 Lower Link Block Nut (3/4” Slotted Nut) 2 .25 PC .156 x 1.5 18 Link Block Cotter Pin 4 .05 E23115 19 Slip Bolt 4 1.25 E939354-6 20 Lock washer 4 E24049 21 Slip Spring 4 .25 E24075 22 Guide Plate Screw 4 .25 E939484-5 23 Guide Plate Nut 4 .15 E939672-17 24 Cotter Pin 4 .01 E30216 25 Retainer (3-1/2” – 7”) 2 E30211 26 Shoulder Screw 4 E20213 27 Rubber Bushing 4 E941286-73 28 Insert Retainer Screw 4 PSN .875 29 Upper Link Block Nut (7/8” Slotted Nut) 2 E24056 32 Spacer 8

YC INSERTS AOT # Item No. Description No. Req. Wt. (lbs.) E16407 31 7” x 7” YC Insert 24 E24748 31 7” x 6-5/8” YC Insert 24 E16407 31 5-1/2” x 5-1/2” YC Insert 16 E24783 31 5-1/2” x 5” YC Insert 16 E16408 31 4-1/2” x 4-1/2” YC Insert 16 E24781 31 4-1/2” x 4” YC Insert 16 E24779 31 4-1/2” x 3-1/2” YC Insert 16

Recommended Spares Include 1 Set Of Inserts For Each Pipe Size To Be Run

YC SETTING RINGS AOT # Item No. Description No. Req. Wt. (lbs.) E30229 34 7” Setting Ring 1 E30226 34 6-5/8” Setting Ring 1 E30223 34 5-1/2” Setting Ring 1 E30220 34 5” Setting Ring 1 E30219 34 4-1/2” Setting Ring 1 E30209 34 4” Setting Ring 1 E34932 34 3-1/2” Setting Ring 1

Recommended Spares Include 2 Setting Rings For Each Pipe Size To Be Run

YC RETAINERS AOT # Item No. Description No. Req. Wt. (lbs.) E30214 33 3-1/2” – 4-1/2” Insert Retainer 4 2.75 E30221 33 5” Insert Retainer E30224 33 5-1/2” Insert Retainer 4 2.13 E30227 33 6-5/8” Insert Retainer 4 2.73 E30230 33 7” Insert Retainer

YC GUIDES PLATES AOT# Item No. Description No. Req. Wt. (lbs.) E24071-2 35 7” Guide Plate 2 3.75 E24071-3 35 6-5/8” Guide Plate 2 4.50 E24071-1 35 5-1/2” Guide Plate 2 5.50 E24071 35 5” Guide Plate 2 7.75 E24071-4 35 4-1/2” Guide Plate 2 8.50 E26827 35 4” Guide Plate 2 8.50 E26827-1 35 3-1/2” Guide Plate 2 8.00


17

AOT HYT 150 TON SLIP TYPE ELEVATOR

AOT # Description Range Size of Links Wt

E39284 HYT Elevator Complete Less Slips 2-3/8” – 3-1/2” 2-1/4” – 3-1/2” 740

HYT SLIP ASSEMBLIES


E39258-2 3-1/2” x 3-1/2” HYT Slip Assembly 170 E39258-4 3-1/2” x 2-7/8” HYT Slip Assembly 170 E39259-2 2-7/8” x 2-7/8” HYT Slip Assembly 170 E39259-4 2-7/8” x 2-3/8” HYT Slip Assembly 170 E39174 3-1/2” HYT Slip Segments Only ( Matched Set of 4) 150 E39175 2-7/8” HYT Slip Segments Only (Matched Set of 4) 150

21

22

20


18

HYT REPLACEMENT PARTS


E39239 3 Hinge Pin 1 12.40 E39162 4 Latch 1 22.00 E39238 5 Latch Pin 1 6.00 E39240 6 Latch Spring 1 .70 E39161 7 Latch Lock 1 8.00 E39251 8 Latch Lock Pin 1 .80 E39241 9 Latch Lock Spring 1 .70 E39253 10 Hinge Pin Retainer 1 .40 E39254 11 Latch Pin Retainer 1 .40 E940308-1 12 Grease Fitting 1 .10 E9519 13 Link Block 2 5.50 P8B .875 x 3 14 Upper Link Block Bolt 2 .50 P8B .75 x 3 15 Lower Link Block Bolt 2 .50 PSN .75 16 Lower Link Block Nut (3/4” Slotted Nut) 2 .15 PC .156 x 1.5 17 Link Block Cotter Pin 4 .05 E52321 18 Slip Bolt 4 1.00 E52539-1 19 Slip Spring 4 .80 E51090 20 Guide Plate 1 8.60 E939098-75 21 Guide Plate Screw 2 .10 E939352-64 22 Guide Plate Lock washer 2 .10 PSN .875 23 Upper Link Block Nut (7/8” Slotted Nut) 2 .15 E939098-96 24 Hex Head Cap Screw 2 .65 E939352-6 25 Lock washer 4 .10 E51089 26 Setting Ring Bushing 2 .15 E939098-36 27 Hex Head Cap Screw 2 .20 E39247 30 3-1/2” & 3-1/2” x 2-7/8” Insert Retainer 4 .25 E39246 30 2-7/8” & 2-7/8” x 2-3/8” Insert Retainer 4 .25

HYT INSERTS


E24774 29 3-1/2” x 3-1/2” Insert 32 .50 E30358 29 3-1/2” x 2-7/8” Insert 32 .75 E24773 29 2-7/8” x 2-7/8” Insert 16 .75 E29255 29 2-7/8” x 2-3/8” Insert 16 1.00


HYT SETTING RINGS


E39214-3 31 3-1/2” HYT Setting Ring 1 11.00 E39214-2 31 2-7/8” HYT Setting Ring 1 11.00 E39214-1 31 2-3/8” HYT Setting Ring



19

AOT HYC 200 TON SLIP TYPE ELEVATOR

AOT # Description Range Size of Links Wt

E55310 HYC Elevator complete less slips & bottom guides 3-1/2” – 7-5/8” 2-1/4” – 3-1/2” 978

HYC SLIP ASSEMBLIES


E70009 7-5/8” x 7-5/8” HYC Slip Assembly 216

E55515 7” x 7” HYC Slip Assembly 224

E55514 7” x 6-5/8” HYC Slip Assembly 227

E55513 5-1/2” x 5-1/2” HYC Slip Assembly 243

E55512 5-1/2” x 5” HYC Slip Assembly 253

E55511 4-1/2” x 4-1/2” HYC Assembly 265

E55510 4-1/2” x 4” HYC Assembly 268

E55509 4-1/2” x 3-1/2” HYC Assembly 274

E55305-1 7-5/8” HYC Slip Segments Only (Matched Set of 4) 176

E55305 7” HYC Slip Segments Only (Matched Set of 4) 184

E55304 5-1/2” HYC Slip Segments Only (Matched Set of 4) 200

E55303 4-1/2” HYC Slip Segments Only (Matched Set of 4) 212


20

HYC REPLACEMENT PARTS


E55311 1 Hinge Pin 1 25.00 E55503 2 Latch 1 47.00 E55312 3 Latch Pin 1 9.00 E34909 4 Latch Spring 1 1.50 E13185 5 Latch Spring Stop 1 .25 E13152 6 Latch Lock 1 4.00 E15101 7 Latch Lock Bolt 1 .75 E13188 8 Latch Lock Spring 1 .25 E8150 9 Latch Lock Bolt Nut 1 .25 E939672-19 10 Cotter Pin 1 .05 E13190 11 Door Lug Pin 1 .65 E55504 12 Hinge Pin Retainer 1 .35 E55505 13 Latch Pin Retainer 1 .20 E940308-1 14 Grease Fitting 1 .10 E9519 15 Link Block 2 5.50 P8B .875 x 3.00 16 Upper Link Block Bolt 2 .50 P8B .75 x 3.00 17 Lower Link Block Bolt 2 .50 PSN .75 18 Lower Link Block Nut (3/4” Slotted Nut) 2 .25 PC .156 x 1.50 19 Link Block Cotter Pin 4 .05 E24076 20 Slip Bolt 4 1.00 E939354-6 21 Lock Washer 4 .25 E945044-2 22 Slip Spring 4 .35 E55508 23 Guide Plate Screw 4 .25 E939484-5 24 Guide Plate Nut 4 .03 E939672-17 25 Cotter Pin 4 .05 E30216 26 Setting Ring Retainer (3-1/2” – 7”) 2 .25 E70147 26 Setting Ring Retainer (7-5/8”) 2 .30 E55501 27 Shoulder Screw 4 .41 E55502 28 Rubber Bushing 4 .04 E941286-73 29 Insert Retainer Screw 4 .08 PSN .875 30 Upper Link Block Nut (7/8” Slotted Nut) 2 .25 E70011 31 7-5/8” Insert Retainer 4 1.85 E30230 31 7” Insert Retainer 4 2.00 E30227 31 6-5/8” Insert Retainer 4 2.00 E30224 31 5-1/2” Insert Retainer 4 2.50 E30221 31 5” Insert Retainer 4 2.25 E30214 31 4-1/2” – 3-1/2” Insert Retainer 4 2.50 PSN .875 35 Upper Link Block Nut (7/8” Slotted Nut) 2 .25

HYC INSERTS


E70010 32 7-5/8” x 7-5/8” Insert 48 .50 E16407 32 7” x 7” Insert 48 .50 E24748 32 7” x 6-5/8” Insert 48 .75 E16407 32 5-1/2” x 5-1/2” Insert 36 .50 E24783 32 5-1/2” x 5” Insert 36 .80 E16408 32 4-1/2” x 4-1/2” Insert 24 .50 E24781 32 4-1/2” x 4 Insert 24 .80 E24779 32 4-1/2” x 3-1/2” Insert 24 1.00



21

HYC SETTING RINGS


E70012 33 7-5/8” HYC Setting Ring 1 11.00 E55522 33 7” HYC Setting Ring 1 11.50 E55521 33 6-5/8” HYC Setting Ring 1 12.00 E55520 33 5-1/2” HYC Setting Ring 1 13.00 E55519 33 5” HYC Setting Ring 1 14.50 E55518 33 4-1/2” HYC Setting Ring 1 15.00 E55517 33 4” HYC Setting Ring 1 16.50 E55516 33 3-1/2” HYC Setting Ring 1 18.00


HYC BOTTOM GUIDE PLATE


E24071-6 34 7-5/8” HYC Bottom Guide Plate (Set) 1 5.00 E24071-2 34 7” HYC Bottom Guide Plate (Set) 1 7.50 E24071-3 34 6-5/8” HYC Bottom Guide Plate (Set) 1 9.00 E24071-1 34 5-1/2” HYC Bottom Guide Plate (Set) 1 11.00 E24071 34 5” HYC Bottom Guide Plate (Set0 1 15.50 E24071-4 34 4-1/2” HYC Bottom Guide Plate (Set) 1 17.00 E26827 34 4” HYC Bottom Guide Plate (Set) 1 17.00 E26827-1 34 3-1/2” HYC Bottom Guide Plate (Set) 1 16.00

RECOMMENDED SPARES INCLUDE 1 SET OF BOTTOM GUIDES FOR EACH PIPE SIZE TO BE RUN

Terms and Conditions 1. Acknowledgement/Acceptance. Sale or lease of any goods or services is expressly conditioned on Buyer’s acceptance of these terms and conditions. Any additional or different terms proposed by Buyer in any document are objected to and rejected and will not be binding upon Seller unless agreed to in writing by Seller. These terms and conditions supersede all prior terms and conditions and shall be the sole terms and conditions which apply to any sale, lease, or other furnishing of goods or services. Seller’s performance of any work shall constitute acceptance by Buyer of these terms and conditions (sometimes “agreement”). 2. Payment. Unless otherwise agreed, payment is due within 30 days of the date of invoice. Buyer shall pay interest at the rate of one and one-half percent (1.5%) per month (18% per annum), or, if lower, the highest rate permitted by law on past due accounts. Seller shall have the right to suspend the fulfillment of any current, incomplete or future orders until Buyer has paid all past due amounts. If Buyer fails to pay for leased goods, Seller may repossess such goods without notice or legal process. 3. Cancellation. Orders cannot be cancelled by Buyer under any circumstances without Seller’s written consent. Buyer agrees to pay a minimum charge of 25% of the order amount on standard items. Higher cancellation charges may apply. Special orders may not be cancelled. The cancellation fee for items made to order will be determined on a case by case basis in Seller’s sole discretion, and Buyer agrees to pay up to 100% of the order amount if cancellation is allowed. 4. Return of Goods. Goods may not be returned without prior written agreement of Seller. As a condition to return all returns must be requested within 30 days of delivery and be undamaged, appropriate for re-sale, and in new condition. In the event Seller agrees to a return, Buyer agrees to make Seller whole, and to pay all shipping charges and a minimum restocking charge of 25% of the invoice amount. Higher return fees may apply. Under no circumstances may any goods be returned that are used, damaged, specially ordered or manufactured, or not regularly stocked by Seller. 5. Taxes/Other Charges. Buyer shall pay any federal, state, local, sales, use, excise or similar taxes, duties, fees or other charges, which Seller may be required to pay or collect, under any existing or future law upon or applicable to the sale, purchase, lease, furnishing, manufacture, processing, transportation, delivery, storage, use or consumption of Seller’s product or services. If Buyer delivers equipment to Seller for inspection and repair and Buyer elects not to repair, if requested by Seller, Buyer shall remove such equipment from Seller’s premises within 90 days of delivery to Seller. Buyer agrees to pay Seller’s storage charges for any equipment remaining on premises after the expiration of such 90 day period. 6. Delivery/Risk of Loss/Title. All sales are “Ex Works” which means Seller fulfills its obligation of delivery when it has made the goods available at its premises (i.e. works, factory, warehouse, etc.), and shall constitute full and final delivery as provided in INCOTERMS, unless otherwise agreed in a writing signed by Seller and Buyer. Title and risk of loss shall pass to Buyer upon delivery. Seller shall retain title to all leased goods. 7. Shipping/Delay. Shipping dates and schedules are subject to prior orders received, availability of adequate labor and equipment and to other unavoidable contingencies as set forth in paragraph 9. Dates of delivery are estimates only, and are dependent upon prompt receipt by Seller of materials and information necessary, in Seller’s sole discretion, to proceed with the work. Seller does not warrant or, in any other way, guarantee delivery dates. Seller reserves the right to choose the facility from which it ships goods to Buyer. 8. Limited Warranty. (a) Subject to the limitations set forth in this Agreement, Seller warrants (1) its mechanical goods sold new shall be free from defects in workmanship or material for one year from delivery; its elastomer goods sold new shall be free from defects in workmanship or material for six (6) months from delivery, (3) leased goods to be in good condition upon delivery, and (4) and repairs on equipment to be free from defects in workmanship or material for 6 months from delivery (but only as to the material or component repaired by Seller). Seller’s sole and exclusive liability for breach of this warranty is expressly limited to, at Seller’s sole option, the repair or replacement, Ex Works Seller’s facility or on location, of the good which proves to be defective during the warranty period, or a refund of the consideration paid for the defective good. Buyer shall pay for repairs due to damage to equipment caused by Buyer and all freight charges and mileage. (b) Seller will use reasonable efforts to provide competent commissioning personnel. Seller does not guarantee the results of these services because of the nature of the work and unpredictable conditions. Seller warrants the commissioning services performed hereunder for a period of thirty (30) days. Seller’s liability for breach of this warranty is expressly limited to, at Seller’s sole option, the re-performance of services which prove to be defective during the warranty period or a refund of the consideration paid for the services. (c) Goods furnished by Seller but not manufactured by Seller will carry only the warranty of the manufacturer of the product, if any. Seller does not warrant any product not manufactured by Seller. (d) These warranties and remedies are conditioned upon: (a) the proper storage, installation, operation, and maintenance of the product, in accordance with the manuals and information provided by or available from Seller or its suppliers or vendors; (b) Buyer keeping accurate records of the operation and maintenance of the product during the warranty period and providing such records to Seller on request; (c) modification or repair of any product only as authorized by Seller, (d) Buyer promptly notifying the Seller of any defect in writing during the warranty period, and (e) Buyer keeping such goods or the results of services in a condition that can be examined by Seller and, upon request by Seller, returning the product to a facility designated by Seller for testing and inspection. Any repair, replacement or performance by Seller shall not extend the warranty period. (e) These warranties shall not apply (i) if the product or result of service had been subject to misuse, negligence, modification, or use other than as specified by Seller, (ii) if Buyer uses the goods with components which are not manufactured or approved by Seller, (iii) if the product does not perform or requires replacement due to normal wear and tear, and (iv) if the design or any part of it was provided by Buyer or Buyer’s behalf to Seller. (f) This section provides the exclusive remedy for all claims based upon a failure of or defects in goods or services, whether the failure or defect occurs during the warranty period, and whether a claim is based

upon contract, warranty, indemnity, tort, extra-contractual liability (including negligence), strict liability, or otherwise. These warranties are exclusive and are in lieu of any other warranties of any kind, written, oral, implied, statutory, or otherwise, including, but not limited to, the implied warranties of merchantability or fitness for a particular purpose or course of performance, course of dealing, or usage of trade.. 9. Force Majeure. Seller shall not be liable for any delay, inability to accept delivery or other failure of performance, or any loss or damage, where such delay, failure of performance, loss or damage results from any cause beyond Seller, its suppliers, or contractor’s control, including, but not limited to, the elements, weather, lack of or inability to obtain materials, fuel, transportation or supplies, acts of Buyer, acts of civil or military authorities, acts of terrorism, insurrection, or war, Acts of God, power or utility failures, breakdown of equipment, machinery, tools, or production facilities, differences with workmen, strikes, boycotts, fire, flood, or other casualty, labor shortages, government regulations or requirements, whether similar or dissimilar to those enumerated, and whether or not foreseeable. 10. Limitation of Liability. (a) The total liability of Seller for any loss or of any kind to Buyer, Buyer’s property, or any other person or person’s property, from Seller’s product or services’ failure to conform to any specification, breach of warranty, negligence or other failure to conform to any standard of care, strict liability, or patent infringement, shall not exceed the amount received by Seller from Buyer for such goods and services. If Seller uses goods of other manufacturers or suppliers in Seller’s goods, and such goods are defective, Seller’s liability shall exist only to the extent that Seller is able to recover from such manufacturer or suppliers for such defects. This limitation of liability shall apply regardless of whether a loss or damage is caused by the sole, joint, or concurrent fault or negligence of Seller or third parties or is based upon contract, warranty, indemnity, tort/extra-contractual liability (including negligence), strict liability, or otherwise. (b) IN NO EVENT SHALL SELLER BE LIABLE FOR, AND BUYER EXPRESSLY RELEASES, INDEMNIFIES, AND HOLDS HARMLESS SELLER FROM AND AGAINST ANY AND ALL LIABILITY FOR PUNITIVE, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOST PROFITS, BUSINESS INTERRUPTION, LOSS OR INABILITY TO USE PROPERTY OR EQUIPMENT, LOSS OF WELL, RESERVOIR/UNDERGROUND DAMAGE, LOSS OF OIL, GAS OR OTHER MINERALS, DAMAGES AND EXPENSES DUE TO BLOW OUT, AND DAMAGES OR EXPENSES DUE TO POLLUTION, REGARDLESS OF WHETHER ANY SUCH LOSS OR DAMAGE IS CAUSED BY THE SOLE, JOINT OR CONCURRENT FAULT OR NEGLIGENCE OF SELLER OR THIRD PARTIES OR IS BASED UPON CONTRACT, WARRANTY, INDEMNITY, TORT/EXTRA-CONTRACTUAL LIABILITY (INCLUDING NEGLIGENCE), STRICT LIABILITY, OR OTHERWISE. 11. INDEMNITY/RELEASE. (a) BUYER ACKNOWLEDGES THAT IT IS A SOPHISTICATED USER, BUYER’S USE OF THE GOODS IS SUBJECT TO THE SOLE DISCRETION AND CONTROL OF BUYER, AND BUYER IS IN THE BEST POSITION TO KNOW IF THE PRODUCT IS APPROPRIATE FOR USE UNDER THE CIRCUMSTANCES. (b) EXCEPT AS EXPRESSLY PROVIDED OTHERWISE IN THIS AGREEMENT, BUYER HEREBY ASSUMES (AND SELLER DISCLAIMS) ANY LIABILITY FOR BUYER’S USE OF THE GOODS. BUYER RELEASES SELLER AND AGREES TO DEFEND, INDEMNIFY AND HOLD HARMLESS SELLER AND ITS PARENT, SUBSIDIARY AND AFFILIATED COMPANIES, THEIR AGENTS, SERVANTS, EMPLOYEES, OFFICERS, DIRECTORS AND INSURERS (“SELLER GROUP”), FROM ALL DEMANDS, CLAIMS, PROCEEDINGS AND SUITS OF ANY KIND (HEREAFER “CLAIMS”), AND ALL DAMAGES, JUDGMENTS, LIABILITIES, FINES, PENALTIES, ASSESSMENTS AND LOSSES OF ANY KIND INCLUDING, WITHOUT LIMITATION, ATTORNEYS FEES, EXPERT WITNESS FEES, EXPENSES AND OTHER COSTS OF LITIGATION (HEREAFTER “LOSSES”) ASSERTED AGAINST OR INCURRED BY SELLER GROUP BY REASON OF, ARISING OUT OF, OR IN ANY WAY RELATED TO BUYER’S USE (OR ANY SUBSEQUENT END USER’S USE) OF SELLERS GOODS, SERVICES OR PRODUCTS, REGARDLESS OF WHETHER OR NOT THE CLAIMS OR LOSSES ARE CAUSED BY OR RESULTS FROM THE ACTUAL OR ALLEGED NEGLIGENCE, STRICT LIABILITY, FAULT OR OTHER WRONGFUL CONDUCT OF SELLER AND/OR ANY OTHER PERSON, OR ENTITY, IN WHOLE OR IN PART, WHETHER SOLE, JOINT, ACTIVE OR PASSIVE, AND EVEN IF BUYER IS WITHOUT ANY LEGAL FAULT OF ANY KIND. (c) IF BUYER IS SUPPLYING SELLER’S GOODS OR SERVICES TO A THIRD PARTY, BUYER SHALL PROVIDE THESE TERMS AND CONDITIONS TO THE THIRD PARTY AND REQUIRE THE THIRD PARTY TO AGREE TO BE BOUND BY THESE TERMS AND CONDITIONS. IF BUYER DOES NOT OBTAIN THIS AGREEMENT, BUYER AGREES TO DEFEND, INDEMNIFY AND HOLD HARMLESS SELLER GROUP FROM AND AGAINST ANY AND ALL CLAIMS AND LOSSES (AS DEFINED IN (b) ABOVE), WHICH SELLER GROUP MAY INCUR AS A RESULT OF BUYER’S FAILURE TO TRANSMIT THE TERMS AND CONDITIONS OR OBTAIN SUCH AGREEMENT, REGARDLESS OF WHETHER OR NOT ANY LOSS OR DAMAGES WERE CAUSED IN WHOLE OR IN PART BY THE SOLE, JOINT, OR CONCURRENT NEGLIGENCE OF SELLER GROUP OR ANY OTHE PERSON OR ENTITY. (d) NOTHWITHSTANDING THE FORGOING, EACH PARTY AGREES TO INDEMNIFY THE OTHER PARTY, THEIR PARENT, SUBSIDIARY AND AFFILIATED COMPANIES, THEIR AGENTS, SERVANTS, EMPLOYEES, OFFICERS, DIRECTORS, INSURERS, SUCCESSORS AND ASSIGNS (THE INDEMNITEES), FROM AND AGAINST ANY AND ALL CLAIMS AND LOSSES (AS DEFINED IN (b) ABOVE) INCURRED AS A RESULT OF ANY CLAIM ASSERTED BY ITS OWN EMPLOYEES AGAINST THE INDEMNITEES, REGARDLESS OF WHETHER OR NOT THE CLAIM OR LOSS IS CAUSED BY OR RESULTS FROM THE ACTUAL OR ALLEGED NEGLIGENCE, STRICT LIABILITY, FAULT OR OTHER WRONGFUL CONDUCT OF THE INDEMNITEES AND/OR ANY OTHER PERSON, OR ENTITY, IN WHOLE OR IN PART, WHETHER SOLE, JOINT, ACTIVE OR PASSIVE, AND EVEN IF BUYER IS WITHOUT ANY LEGAL FAULT OF ANY KIND.

12. Insurance. Each party agrees to maintain comprehensive general liability insurance providing coverage for the indemnity obligations in this agreement. Such insurance shall be endorsed to provide (i) it is primary to the other party’s insurance and (ii) it waives subrogation against the other party, their parent, subsidiary and affiliated companies, and their agents, servants and employees. 13. Change of Design. Seller expressly reserves the right to (i) change or modify the design and construction of any of its goods without obligation to furnish or install such change or modification on goods previously sold and (ii) make substitutions and modifications to its product or services, so long as the changes do not adversely affect the performance of those items. 14. Patents. (a) Seller agrees to indemnify and hold harmless Buyer from and against all claims, suits, and costs of patent infringement related to goods or services provided by Seller, expressly subject to the following conditions: (i) Buyer must promptly notify Seller in writing upon receipt of any claim for infringement or service of any suit for infringement, (ii) Buyer must make no admission of liability and must unconditionally afford Seller the opportunity, at Seller’s sole option and expense, to answer such claim or suit, assume control of the defense, and settle, compromise, or try such matter as Seller sees fit, (iii) Buyer must provide Seller with full disclosure and assistance that may reasonably be required to defend and claim or suit. (b) This indemnity shall not apply to (i) any product not manufactured by Seller, (ii) any product specially made, in whole or in part, to Buyer’s design specifications, (iii) any product used in combination with other goods or materials in such a manner that the combination (and not the product manufactured by Seller) is the basis for the claim of infringement, (iv) any product for which Seller has offered an update or change, which would prevent the claim or suit, and (v) any product that has been altered, modified, or revised by Buyer. (c) Paragraph 10(b) of these terms and conditions excluding any liability for consequential damages is incorporated by reference as if fully set forth here. Seller’s liability under this indemnity shall not exceed the amount received by Seller for such product or services claimed to be infringing. (d) Seller may, at its option, (i) procure for Buyer the right to continue using the product or service, (ii) modify or replace it in whole or in part to avoid infringement, or (iii) take back the product or discontinue service and refund any fees received by Seller for the infringing product or services. (e) This indemnity is in lieu of any other warranty or indemnity, express or implied, with respect to infringement and states Seller’s entire liability for indemnification for patent, trademark, copyright, and trade secret infringement for goods and services. 15. Confidentiality. Information regarding Seller’s services, equipment, goods, and materials will be held by Buyer in confidence, and may be released to others only upon written approval of Seller or when required by law. This provision shall not apply to information that becomes generally available to the public other than through disclosure by Buyer. Seller retains all rights to all designs, engineering details, and data concerning the goods and services provided and nothing herein shall grant Buyer a license under any invention, patent, trademark or copyright now or hereafter owned by Seller. 16. Liens. Buyer grants Seller a purchase money security interest in the goods for any portion of the purchase price not paid at delivery and Seller shall retain this interest until Buyer has been paid in full. 17 Alternative Dispute Resolution. Any dispute arising out of or in connection with Seller providing goods and services to Buyer, and the interpretation, enforcement, or arbitrability of this agreement, shall be resolved by arbitration under the commercial rules of the American Arbitration Association. Arbitration shall be before a single arbitrator in Houston, Texas. The result of the arbitration shall be final and binding on the parties. The award shall be “reasoned” and any party may enforce the award in any court of competent jurisdiction. The parties shall share the cost of the arbitration equally. 18. NORM/TNORM/Radioactive Materials. Buyer warrants that any used goods returned to Seller shall be free of radioactive material, including NORM and TNORM. BUYER AGREES TO INDEMNIFY, DEFEND, AND HOLD HARMLESS SELLER GROUP (AS DEFINED IN PARAGRAPH 11(b) ABOVE) FROM ANY CLAIMS OF ANY KIND, AND ALL CLAIMS AND LOSSES (AS DEFINED IN 11 (b) ABOVE), RELATED TO ANY CLAIM BY ANY PERSON AGAINST SELLER GROUP THAT ANY OF SELLER’S GOODS CAUSED BODILY INJURY, SICKNESS, DISEASE, OR DEATH OF ANY PERSON BY DUE TO EXPOSURE TO NORM, TNORM, OR ANY RADIOACTIVE MATERIALS. WITH RESPECT TO NORM, TNORM, AND RADIOACTIVE MATERIALS, SELLER SHALL HAVE NO OBLIGATION TO INDEMNIFY AS SET FORTH IN PARAGRAPH 11(d). 19. Export Laws. All sales are subject to United States Export Laws and Regulations, which may restrict the export or re-export to certain countries. Buyer agrees to abide by such export and re-export laws and regulations. 20. Lost or Damaged Rental Equipment. If rental equipment is lost or damaged beyond repair (as determined in Seller’s sole’s discretion), Buyer shall pay Seller the Seller’s U.S. list sales price for such equipment; if repaired, Buyer shall pay all costs of repair, including shipping charges. Upon payment of list price, Buyer’s rental payment shall cease. If Buyer has agreed to daily rental, Buyer shall pay the rental payment until repairs are complete. If leased for a term as stated in the quote, Buyer shall pay rental for the term. 21. General Clauses. Independent Contractor. Seller is an independent contactor and not an employee, agent, joint venturer, or partner of Buyer. Governing Law. This agreement is governed by the laws of the State of Texas, without regard to its conflicts of law principles. Notices. Any notices required by this Agreement shall be considered given when received by the other party. Waiver. Any delay or failure to enforce any of these terms and conditions shall not bar any subsequent enforcement of the terms and conditions or be deemed a waiver of any subsequent breach. Severability. All parts of these terms and conditions are severable. The invalidity of any part shall not affect the validity of any other part. If any clause is determined to be unenforceable, the remaining terms and conditions shall be enforced to the maximum extent permissible. Entire Agreement. This is the entire agreement of the parties and supersedes all prior oral or written agreements. Buyer acknowledges that it has not relied on any representations other than those in this agreement. There are no understandings or agreements which are not expressed herein.

Documents

Elevator