ENCLS/MBOX/IQ22x Metal Box Data Sheet TA200203 Issue 2 , 26-Nov-2012 1

Data Sheet

ENCLS/MBOX/IQ22xMetal Box

Metal Box

Description

The MBOX/IQ22x consists of a metal box with a hinged lid. It is designed to enclose a NBOX product (e.g. IQ22x, NBOX/EINC, NBOX/TMN) and provides cable glanding and protection.

Features

• Hinged front panel with captive screws• M20 glanding on all faces• Rear slots for 25 way D type terminated cables.• Integral earth busbar• Front cutouts to view display panel and indicators• 3 hole fixing

Physical

dimensions in mm (inches)

261 mm (10.27”)

45 mm (1.77”)

77 mm (3.03”)

285

mm

(11.

22”)

display panel aperture

Indicators aperture

M20 (.78”) cable gland knockouts

2 screws

2 ENCLS/MBOX/IQ22x Metal Box Data Sheet TA200203 Issue 2 , 26-Nov-2012

ENCLS/MBOX/IQ22x Data Sheet

Please send any comments about this or any other Trend technical publication to techpubs@trendcontrols.com

© 2012 Honeywell Technologies Sàrl, ECC Division. All rights reserved. Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Z.A. La Pièce, 16, 1180 Rolle, Switzerland by its Authorized Representative, Trend Control Systems Limited.

Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation to notify any person of such revisions or changes.

Trend Control Systems LimitedAlbery House, Springfield Road, Horsham, West Sussex, RH12 2PQ, UK. Tel:+44 (0)1403 211888 Fax:+44 (0)1403 241608 www.trendcontrols.comTrend Control System USA6670 185th Avenue NE, Redmond, Washington 98052, USA. Tel:(425) 869-3900 Fax:(425) 869-8445 www.trend-americas.com

FUNCTIONALITyThe MBOX/IQ22x consists of a tray with a hinged front panel held closed by two screws. It is designed to hold the NBOX (e.g. IQ22x) with three tapped holes and screws to accommodate the NBOX fixings. The front panel has an aperture to view the display panel, and another to view the indicators.

The box has three point fixing via a 5 mm keyhole, and two holes. It has knockout M20 glanding in all tray faces, with grommetted slots in the top face and rectangular holes (suitable for cables terminated in 25 Way D type connectors) in the rear.

It is pre-fitted with a brass busbar complete with a bag of busbar screws.

Suitable NBOX devices include: IQ22x NBOX/XNC220 NBOX/TMN/.. NBOX/EINC NBOX/INC

INSTALLATIONThe MBOX/IQ22x is well provided with cable entry points:

The installation involves:

Fix box to wall, or other flat surface using 3 point fixingIdentify cable routingKnockout holes for cable entryInstall glands and cable conduitRoute cablesMount NBOX device using three point fixing

OrDEr CODEENCLS/MBOX/IQ22x: Metal box for NBOX device complete with busbar, busbar screws, device fixing screws, earthing cable and installation instructions.

SPECIFICATIONMechanical

Dimensions :261 x 285 x 77 mmWeight :1.66 kgMaterial Box :2 mm mild steel with epoxy textured finish Grommets :Silicon rubber

Environmental

Protection :IP30

M20 knockouts

M20 knockouts

M20 knockoutsM20 hole

M20 slots with grommetshole for 25 Way D type

earthing cable

integral earth bus

104.5 mm(4.114”)

209 mm (8.228”)

Ø 6 mm(0.23”)Ø 12 mm(0.47”)

227

mm

(8.9

37”)

2 holes Ø 6 mm (0.23”)

Full details of MBOX/IQ22x installation are given in ENCLS/MBOX/IQ22x Installation Instructions (TG200204)

Make off cable screens to busbarComplete device installation as described in IQ22x installation instructionsEarth the boxClose cover and tighten screws.

It has 3 point fixing via keyhole and two holes: