English Book ASB-203[2]

8/6/2019 English Book ASB-203[2]

1/13

A ptitude Decoder of aptitude

Instruction

2005-8


2/13

Aptitude Instruction

CONTENT

CHAPTTER 1 Summarization

CHARPTER 2 Panel introduction

CHARPTER 3 Technical specifications

CHARPTER 4 Connection decoder with System

CHARPTER 5 Connection decoder with DVR

CHARPTER 6 Connection decoder with PTZ and cameraConnection diagram of decoder and PTZ

(AC24V/AC220V), camera Lens (DC12V):

CHARPTER 7 Address setting

CHARPTER 8 communication protocol, Baud rate setting

CHARPTER 9 PTZ and Camera Lens auto check itself

CHARPTER 10 Equipment Installation

CHARPTER 11 FAQ

CHARPTER 1SUMMARIZATION

The decoder of aptitude is a type of front equipment with

Page 2 of 13


3/13


DVR. The DVR will control the PTZ, Camera Lens,

Auxiliary switch and so on through the decoder of aptitude.

The decoder of aptitude can assemble all kinds of multi-

protocol DVR. Without setting a protocol, it will decode

code automatic quickly according to inner code of protocol

then it will control the front equipments.

The simple decoder of aptitude has a group of function

that controls every group of power of camera, brush,

lamplight and so on.

The decoder of aptitude is unsuitable for the place

flammable and explosive. Be careful to select the suitable

working voltage for PTZ and Camera Lens when the

decoder connects them.

CHARPTER 2PANEL INTRODUCTION

NO Name Specification

1 CODE/POWER Communication/power indicatorlight

2 RS-485 The port of RS-485 communication

Page 3 of 13


4/13


3 CAMERAID Decimal address coding switch(The number of camera)

4 UP/DOWN/LEFT/

RIGHT

Pan/tilt up/down/left/right

5 AUTO Pan/tilt auto6 P/T-COM Pan/tilt com7 P/T VOLTAGE Pan/tilt voltage (AC24V/AC220V)8 ZOOM/FOCUS/IR

IS/

9 LNES COM /10 DC12V/END /11 AUX IN/OUT Wireless auxiliary switch in

common12 AC24V /13 POWER ON/OFF Power switch14 AC220V 50Hz /

CHARPTER 3Technical specifications

Input voltage : 220VAC 10%Pan/tilt voltage: 220VAC/1.0A or 24VAC/1.0A

Camera voltage: 2-15VDC/250Ma

Auxiliary switch: 275VAC/7A

Control signal type : Two core shield twisted lines

CHARPTER 4Connection decoder with system

The decoder of aptitude adopts communication of RS-

485 Bus-mastering. DATA+ is a port of 485+ sign; DATA- is

Page 4 of 13


5/13


a port of 485- sign. GND earth.

The standard RS-485 equipment connects the decoder of

aptitude with two core shield twisted lines. The line is not over

1500m .

The farthest decoder should be a 120ohm of shunt between

485+ and 485- when several decoders connect each other. Thediagram of connection as follows:

CHARPTER 5Connection decoder with DVR

Connect terminal DATA+ to 485+, DATA- to 485-, GND

to GND in correspondence between Rs232 / 485 converter

and decoder. The diagram0 of connection as follows:

Page 5 of 13


6/13


CHARPTER 6Connection decoder with PTZ and Camera

Connection diagram of decoder and PTZ (AC24V/ac220v),camera Lens (DC12V):

Specification:1. Select value to be consistent with pan/tilt working

voltage AC24V/AC220V through (P/T VOLTAGE)

2. Auxiliary, lamplight and brush control switch is NO.,

user may adopt according to actual needs.

CHARPTER 7Address setting

In order to distinguishing different decoders, we use

different address coding.

Page 6 of 13


7/13


8/13


32 0 0 0 0 0 1

CHARPTER 8Communication protocol, Baud rate setting

Coding switch possess 4 switches, they divide into protocol

coding switch and Baud rate coding switch. Protocol coding

switch consists of 1-2, changes the coding for select differentprotocol. Baud rate coding switch consists of 3-4.changes

the coding for select different Baud rate.

The setting of protocol diagram as follows:

Codingswitch O N

O F F

1 2

0O N

O F F

1 2

0O N

O F F

1 2

1O N

O F F

1 2

1

Baud rate 9600 4800 2400 1200

The setting of Baud rate diagram as follows:

Codingswitch O N

O F F

3 4

0O N

O F F

3 4

0O N

O F F

3 4

1 O NF F

3 4

1

protocol AUTO PELCO-

D

PANASONI

C

HT-600

NO Protocol Recommendatory

Baud rate

Remark

Page 8 of 13


9/13


1 CCR-20G 4800 PICASO

2 PELCO-SP 9600 PICO2000

3 KTD-312 9600 PICO

4 PELCO-D 9600

5 PELCO-D2400 2400

6 HT600 4800

7 PELCO-P 9600

Page 9 of 13


10/13


CHARPTER 9PTZ and Camera Lens auto check itself The decoder of aptitude can check itself and can

control PTZ, Camera Lens through coding switches.

Power off. Coding switch 3,4 set ON, the others setOFF.

Power on .The Len checks itself, the light works.

Function Address coding switch

Code switch 1 2 3 4 5 6 1 2 3 4

FOCUS+ 1 0 0 0 0 0 0 0 1 1

Page 10 of 13

8 PANASONIC 9600

9 RM110 9600

10 KTE-301RX 9600 KODICOM

11 KALATEL CYB 9600 GV-800

12 PICO2400 4800

13 YAAN 4800

14 HY 9600

15 PELCO-P 4800 MATRIX/CONTROL

16 KALATEL 4800

17 MV 9600

18 ADT 9600


11/13


12/13


CHARPTER 10Equipment Installation

1. Fix the decoder firmly on a suitable place

2. Set correct address coding according to the number

of camera

3. Connect all lines according to the instruction for the

connection and confirm them where are right.

Page 12 of 13


13/13


4. Operate controller, when the decoder receives

correct orders, the light CODE flash quick on end.

CHARPTER 11FAQ

Fault1: The indicator doesnt work

Answer:

1. Is the supply power voltage is right?2. Are they contact plug with socket?

3. is fuse burn or loose?

Fault2: The decoder cant be operate by DVR

Answer:

1. Is the connection between DVR and the

decoder of aptitude right?

2. Whether address coding switch setting the

same with DVR

3. Decoder control line length whether over

1200m.

Page 13 of 13

Documents

English Book ASB-203[2]