Upload
duongnhan
View
250
Download
1
Embed Size (px)
Citation preview
Enhanced Reusable Components by Using NXOpen in the Product
Template Studio
Presentation by: Sönke Tobias Hoppe
Duration: 30 Minutes
09.06.2017 1
About me
Sönke Tobias Hoppe
24 years old
Naval Architecture and Ocean Engineering
University of Applied Sciences Bremen, Germany
NX Experience: 1,5 years
Bachelor Thesis with Digitread and Skipsteknisk
Master Thesis with Digitread Finished: approx. beginning of 2018
09.06.2017 2
Agenda
1. Simulation of the Equilibrium Position of Pulleys
2. NXOpen Supported Multidisciplinary Design Optimization (MDO)
3. Pro / Contra
4. Conclusion
5. Questions
09.06.2017 3
Simulation of the Equilibrium Position of Pulleys
09.06.2017 4
Introduction & Motivation
Feasibility study
Equilibrium position of pulleys
e.g. on fishery vessels
Automation of complex workflow
Different software: not possible
NX Motion Simulation: possible
Template to guide the user through the workflow
NXOpen as powerful support
09.06.2017 5
Initial Situation: Problems
Feasible result: Tangent wheel surfaces
Wheel always below wire
No intersection with structure
Manually solving constraints mostly results in: Orientation is upside down
Scratching onto surrounding structure
09.06.2017 6
Initial Situation: Analysis
Solution can be found under various circumstances
Splitting calculation
09.06.2017 7
Equilibrium position
Initialisation process
Approximate position
Definition of the connection
Initial Situation: Analysis
Simulating gravity
Resetting static solution: Suppressing constraints, features, components
Bringing components into an upright position Initial position of measurement points
09.06.2017 8
Initialisation process
Initial Situation: Analysis
Determine solution iteratively
Using CAE Motion Simulation Application
Additional knowledge required to: simulate DoF
connect pulleys
No exact solution
Capability allows position update
Requires saving procedure Causes problems on components with read-only
permissions
09.06.2017 9
Approximate position
Initial Situation: Analysis
Constraining in right order
Influence on other constraints
Measurement points used to predict constraints
Sequences of logical checking methods
09.06.2017 10
Definition of the connection
Enhanced Reusable Component: Automation
Solving complex workflows with one click
NXOpen in Product Template Studio
09.06.2017 11
Equilibrium position
Definition of the connection
Approximate position
Initialisation process
Action button
Enhanced Reusable Component: Automation
09.06.2017 12
Equilibrium position
Initialisation
Dynamic motion analysis
Finite element method
Consistence of scenario
Pulley position
Dimensioning
User interaction Automated process Automated CAE simulations
Update Structure
Enhanced Reusable Component
09.06.2017 13
09.06.2017 14
NXOpen Supported Multidisciplinary Design Optimization
Introduction to Master Thesis
Multidisciplinary Design Optimization on a Parametric RoPAX Vessel
NX ➝ HEEDS ➝ Star-CCM+
MDO for better results
Guiding user through workflow Initial design idea ➝ optimization
Initial main dimensions received from own application
Automated CFD setup using Star-CCM+ with or without EHP-Tool
CAE model creation
Optimization in Heeds
09.06.2017 15
Enhanced Reusable Component
09.06.2017 16
PRO / CONTRANXOpen in Reusable Components
09.06.2017 17
Pro / Contra
09.06.2017 18
PRO CONTRA
Requires programming skills
Error handling
Automating workflows
Requires less user knowledge
Enlarges functionality of NX
Allows quick design changes
Conclusion onNXOpen in Reusable Components
09.06.2017 19
Conclusion
NXOpen delivers fundamental simplifications
NX can simulate the equilibrium position
Performing logical checking methods
Proceeding through constraints
Editing expressions
Parametric simulations incl. post processing
Running external applications
Just one click necessary once it is set up
09.06.2017 20
Thank you for your attentionPresentation by: Sönke Tobias Hoppe
09.06.2017 21
Enhanced Reusable Components by using NXOpen in the Product Template Studio
The usage of Reusable Components increased the productivity of engineers. However, workflows of engineers could still be improved by solving and optimizing relevant modelling data with embedded simulations. The NXOpen Interface gives the possibility to carry out simulations, including pre/post processing, and to display results in a single modelling PTS with just one click.
Sönke Tobias Hoppe30 Minutes
09.06.2017 22