3
Issued : 01 Feb 1984 Spsds : 8402/N1 ENPREP 110 EC Alkaline soak cleaner INTRODUCTION ENPREP 110 EC is especially developed for use in energy conserving systems. It is designed for use at lower temperatures than normal which will result in considerable savings in energy consumption. ENPREP 110 EC is a highly efficient alkaline soak cleaner, suitable for steel, copper and brass. OPERATING CONDITIONS Concentration 40 - 80 g/l Temperature 40 - 70°C Tanks and heaters Steel Agitation Mechanical or mild air is beneficial The exact concentration and temperature required will depend on the time available and the type of soil to be removed. It is not advised to operate at temperatures above 70°C since this will cause unnecessarily high heating costs. MAKE-UP PROCEDURE Important Please read handling and storage instructions before preparing the solution. Fill the tank ¾ full with water and heat to about 50°C. The required amount of ENPREP 110 EC should be added with continuous stirring. When dissolved, adjust the solution to the desired level and adjust to the operating temperature. CLEANER CONTROL Take a 10 ml sample of the working solution. Dilute to 150 ml with demineralised or deionised water. Add 5 to 6 drops of Phenolphthalein indicator. Titrate with 1N hydrochloric acid until the colour changes to the first permanent yellow. ml titrated x 5.65 = g/l ENPREP 110 EC

Enprep_110-EC-Steel-Cu-Brass

Embed Size (px)

DESCRIPTION

Enprep_110-EC-Steel-Cu-Brass

Citation preview

Page 1: Enprep_110-EC-Steel-Cu-Brass

Issued : 01 Feb 1984Spsds : 8402/N1

ENPREP™ 110 ECAlkaline soak cleaner

INTRODUCTION

ENPREP 110 EC is especially developed for use in energy conserving systems.It is designed for use at lower temperatures than normal which will result in considerable savings in energyconsumption.

ENPREP 110 EC is a highly efficient alkaline soak cleaner, suitable for steel, copper and brass.

OPERATING CONDITIONS

Concentration 40 - 80 g/lTemperature 40 - 70°CTanks and heaters SteelAgitation Mechanical or mild air is beneficial

The exact concentration and temperature required will depend on the time available and the type of soil to beremoved. It is not advised to operate at temperatures above 70°C since this will cause unnecessarily highheating costs.

MAKE-UP PROCEDURE

Important

Please read handling and storage instructions before preparing the solution.

Fill the tank ¾ full with water and heat to about 50°C. The required amount of ENPREP 110 EC should beadded with continuous stirring. When dissolved, adjust the solution to the desired level and adjust to theoperating temperature.

CLEANER CONTROL

Take a 10 ml sample of the working solution.Dilute to 150 ml with demineralised or deionised water.Add 5 to 6 drops of Phenolphthalein indicator.Titrate with 1N hydrochloric acid until the colour changes to the first permanent yellow.

ml titrated x 5.65 = g/l ENPREP 110 EC

Page 2: Enprep_110-EC-Steel-Cu-Brass

ENPREP™ 110 ECTechnical data sheet

Page 2 of 3

WASTE DISPOSAL

Solutions of ENPREP 110 EC are alkaline. Disposal often only required neutralisation to pH 6-8 with an acid,allowing the sludge to settle and discharge liquid to sewer.However, local regulations on effluent discharge may require other treatment and you are advised to check withyour Regional Water Authority.Enthone - OMI will be pleased to advise on any specific installation.

HANDLING & STORAGE

ENPREP 110 EC is an alkaline material.Contact with eyes and skin should be avoided.Protect eyes with goggles and wear protective clothing.In case of eye contact flush with water and seek medical attention.Store in dry away from acids and foodstuffs.

Page 3: Enprep_110-EC-Steel-Cu-Brass

ENPREP™ 110 ECTechnical data sheet

Page 3 of 3

HANDLING AND SAFETY INSTRUCTIONS

For detailed information consult the material safety data sheets for this product.Please read material safety data sheets carefully before using this product.

DISCLAIMER

All recommendations and suggestions in this bulletin concerning the use of our products are based upon testsand data believed to be reliable. Since the actual use by others is beyond our control, no guarantee expressedor implied, is made by Enthone, its subsidiaries of distributors, as to the effects of such use or results to beobtained, nor is any information to be construed as a recommendation to infringe any patent.

™ Trademark licensed from Enthone Inc.

ADDRESSES

AUSTRIA FRANCE BENELUX

Enthone GmbHGroßmarktstraße 201230 Wien, AustriaTel.: 43-161668440Fax.: 43-16167084

Enthone S.A.S.Rue Léon JouhauxCroissy-Beaubourg77312 Marne la Vallée, FranceTel.: 33-160059360/Fax:33-143026784

Enthone B.V.Koenendelseweg 295222 BG ‘s-HertogenboschThe NetherlandsTel.: 31-736280111/Fax: 31-736219283

ITALY GERMANY SWITZERLAND

Enthone S.r.l.Via B. Buozzi, 2020097 San Donato Milanese MI< ItalyTel.: 39-02518941Fax: 39-025279890

Enthone GmbHElisabeth-Selbert-Strasse 440764 Langenfeld, GermanyTel.: 49-21738490-0Fax: 49-21738490-200

ERNE surface AGIndustriestrasse 248108 Dällikon, Zürich, SwitzerlandTel.: 41-18441144Fax: 41-18441145

GREAT BRITAIN SPAIN SWEDEN

Enthone LtdForsyth Road, Sheerwater, WokingSurrey GU21 5RZ, EnglandTel.: 44-1483758400Fax: 44-1483728837

Enthone España S.A.118, Carretera Reial08960 Sant Just Desvern, BarcelonaEspanaTel.: 34-934803388/Fax:34-934803389

Enthone ABSöderleden 10660006 Norrköping, SwedenTel.: 46-11240600Fax: 46-11126833

HUNGARY CZECH REPUBLIC POLAND

Enthone KFTIpari Park 192330 Dunaharaszti, HungaryTel.: 36-24460-566Fax: 36-24460-577

Enthone s.r.o.Severovychodnl V 146/154114100 Praha 4, Sporilov, Czech RepublicTel.: 420-272770665Fax: 420-272767842

Enthone Sp.z.o.o.U1 Obuwnicza 326-100 Skarzysko-KamiennaPolandTel:48-412521523/fax: 48-412521574

PORTUGAL TURKEY ISRAEL

Enthone Portugal Lda.Rua Bouca dos Estilhadouros 2714445-044 AlfenaPortugalTel.: 351-229686620Fax: 351-229686623

Enthone Galvanoplasti Sanayi Ticaret A.S.Ikitelli Organize Sanayi Turgut ÖzalCd Galvano Teknik Sitesi,A Blok No.33, Ikitelli, InstanbulTurkeyTel.: 90-2126710384/Fax: 90-2126710388

AMZA Ltd.PO Box 86252108 Ramat GanISRAELTel.: 972-3-9211505Fax.: 972-3-9212187

cooksonelectronics.com