EP 1110-1-8 (Vol. 1), Construction Equipment Ownership and ... · iii construction equipment ownership and operating expense schedule table of contents (continued) chapter 4.0 - methodology

EP 1110-1-8 Volume 1

November 2009

Construction Equipment Ownership and Operating Expense Schedule Region I

DEPARTMENT OF ARMY U.S. Army Corps of Engineers Washington, DC 20314-1000

This pamphlet supersedes EP 1110-1-8, dated 31 July 2007.

REPLY TO ATTENTION OF:

CECW-EC Pamphlet 30 November 2009 No. 1110-1-8, Vol. 1

CONSTRUCTION EQUIPMENT OWNERSHIP AND OPERATING EXPENSE SCHEDULE

1. Purpose. This pamphlet is authorized by and established in accordance with Federal Acquisition Regulation (FAR) 31.105 and Engineer Federal Acquisition Regulation (EFAR) SUBPART 31.105. This pamphlet establishes predetermined equipment ownership and operating expense rates for construction equipment. This pamphlet also establishes a method to calculate equipment ownership and operating expense rates for construction equipment when the predetermined rates are not considered appropriate. The overall intent of this pamphlet is to determine equipment costs that are fair and reasonable. Expense factors for calculating dredge plant and marine equipment costs are provided in chapter 4. 2. Applicability. This pamphlet applies to all USACE commands. It is applicable to all solicitations and contracts for construction expected to exceed the Simplified Acquisition Threshold of $100,000 when actual cost data for both ownership and operating costs cannot be determined. This volume is for use in Region I, which includes the following states: Connecticut Maine Massachusetts New Hampshire New Jersey

New York Pennsylvania Rhode Island Vermont

3. References. See APPENDIX A. 4. Distribution Statement. Approved for public release, distribution is unlimited. FOR THE COMMANDER: 12 Appendixes STEPHEN L. HILL (See Table of Contents) Colonel, Corps of Engineers

Chief of Staff

EP 1110-1-8, Vol. 130 Nov 09

[This page intentionally left blank]

EP 1110-1-8, Vol. 130 Nov 09

i


Table of Contents

CHAPTER 1.0 - INTRODUCTION

1.1 Use .................................................................................................................... 1-1 1.2 Decision Flow Process ...................................................................................... 1-1 1.3 How to Obtain Assistance.................................................................................. 1-1 1.4 How to Obtain CHECKRATE Spreadsheet........................................................ 1-2 1.5 How to Obtain this Publication........................................................................... 1-2

CHAPTER 2.0 - METHODOLOGY FOR CONSTRUCTION EQUIPMENT SECTION I. GENERAL...............................................................................................2-1 2.1 Contents ............................................................................................................ 2-1 2.2 Basis for Equipment Rates ................................................................................ 2-1 2.3 Total Hourly Rate............................................................................................... 2-1 SECTION II. OPERATING CONDITIONS...................................................................2-2 2.4 Average, Difficult, or Severe Conditions ............................................................ 2-2 2.5 Determination of Condition ................................................................................ 2-3 SECTION III. EQUIPMENT SELECTION....................................................................2-3 2.6 General.............................................................................................................. 2-3 2.7 Truck Selection.................................................................................................. 2-3 2.8 Crawler Tractor Selection .................................................................................. 2-3 2.9 Equipment Accessories ..................................................................................... 2-4 SECTION IV. EQUIPMENT VALUE ...........................................................................2-4 2.10 List Price and Accessories................................................................................. 2-4 2.11 Discount Code (DC) .......................................................................................... 2-4 2.12 Sales or Import Tax ........................................................................................... 2-4 2.13 Freight ............................................................................................................... 2-4 2.14 Total Equipment Value (TEV)............................................................................ 2-4 SECTION V. LIFE .......................................................................................................2-5 2.15 Economic Life (LIFE) ......................................................................................... 2-5 2.16 Working Hours Per Year (WHPY)...................................................................... 2-5 SECTION VI. SALVAGE VALUE ...............................................................................2-5 2.17 Salvage Value (SLV) ......................................................................................... 2-5 2.18 Salvage Value Percentage ................................................................................ 2-5

EP 1110-1-8, Vol. 130 Nov 09

ii


Table of Contents (Continued)

SECTION VII. OWNERSHIP COST............................................................................2-6 2.19 Ownership Elements ......................................................................................... 2-6 2.20 Depreciation ...................................................................................................... 2-6 2.21 Facilities Capital Cost of Money (FCCM)........................................................... 2-7 SECTION VIII. OPERATING COST............................................................................2-7 2.22 Operating Cost Elements .................................................................................. 2-7 2.23 Fuel Cost ........................................................................................................... 2-8 2.24 Filters, Oil, and Grease (FOG) Cost .................................................................. 2-9 2.25 Repair Cost...................................................................................................... 2-10 2.26 Tire Wear Cost ................................................................................................ 2-12 2.27 Tire Repair Cost .............................................................................................. 2-13 SECTION IX. STANDBY HOURLY RATE................................................................2-14 2.28 Standby Hourly Rate ....................................................................................... 2-14 SECTION X. RATE CALCULATION EXAMPLE......................................................2-14 2.29 Computation Example ..................................................................................... 2-14

CHAPTER 3.0 - ADJUSTMENTS TO HOURLY RATES

SECTION I. GENERAL...............................................................................................3-1 3.1 Contents ............................................................................................................ 3-1 3.2 Basis for Equipment Rates ................................................................................ 3-1 3.3 Equipment Rate Adjustment Tables .................................................................. 3-1 3.4 Determination for Use of Equipment Rates in Tables 2-1 and 2-2..................... 3-1 SECTION II. RATE ADJUSTMENTS..........................................................................3-2 3.5 Rate Adjustments .............................................................................................. 3-2 3.6 Changes in Operating Conditions...................................................................... 3-2 3.7 Change in Cost of Money Rate (CMR) .............................................................. 3-2 3.8 Actual Work Hours Greater than 40 Hours per Week........................................ 3-3 3.9 Changes in Fuel Cost ........................................................................................ 3-4 3.10 Adjustments to Fuel, Oil, and Grease (FOG) Cost ............................................ 3-5 3.11 Equipment of Different Age than Table 2-1 ....................................................... 3-5 3.12 Rate Adjustment for Overage Equipment .......................................................... 3-6 3.13 Standby Rate Adjustment for Equipment of a Different Age than Table 2-1...... 3-7 3.14 Equipment Purchased Used.............................................................................. 3-8 3.15 Rate Calculation Examples................................................................................ 3-8

EP 1110-1-8, Vol. 130 Nov 09

iii



CHAPTER 4.0 - METHODOLOGY FOR DREDGING PLANT AND MARINE EQUIPMENT

SECTION I. GENERAL...............................................................................................4-1 4.1 Contents ............................................................................................................ 4-1 4.2 General.............................................................................................................. 4-1 SECTION II. ANNUAL USE........................................................................................4-1 4.3 Time Available to Dredge .................................................................................. 4-2 SECTION III. LIFE ......................................................................................................4-2 4.4 Life..................................................................................................................... 4-2 4.5 Annual Hours Available ..................................................................................... 4-3 SECTION IV. SALVAGE VALUE ...............................................................................4-3 4.6 Salvage Value (SLV) ......................................................................................... 4-3 SECTION V. OWNERSHIP COST..............................................................................4-3 4.7 Ownership Cost ................................................................................................. 4-3 4.8 Depreciation Factor ........................................................................................... 4-4 4.9 The Cost of Money Rate (CMR) Factor ............................................................. 4-4 4.10 Other Ownership Elements................................................................................ 4-5 SECTION VI. OPERATING FACTORS ......................................................................4-5 4.11 Hourly Operating Cost ....................................................................................... 4-5 4.12 Prime and Secondary Power............................................................................. 4-5 4.13 Water, Lube, and Supplies (WLS) ..................................................................... 4-6 4.14 Repairs (RPR) ................................................................................................... 4-6 SECTION VII. STANDBY............................................................................................4-7 4.15 Standby Rate..................................................................................................... 4-7 SECTION VIII. NEGOTIATED PROCUREMENT .......................................................4-7 4.16 Rates ................................................................................................................. 4-7 4.17 Allowance for Additional Capital Improvements................................................. 4-8 4.18 Overage Plant.................................................................................................... 4-8 4.19 Dredging Plant Purchased Used ....................................................................... 4-8 SECTION IX. RATE CALCULATION EXAMPLE .......................................................4-8 4.20 Rate Calculation Example ................................................................................. 4-8

EP 1110-1-8, Vol. 130 Nov 09

iv



List of Tables

Table 2-1. Hourly Equipment Ownership and Operating Expense ............................2-21 Table 2-2. Hourly Rate Elements.............................................................................2-253 Table 3-1. Equipment Age Adjustment Factors ...........................................................3-9 Table 3-2. Equipment Age Adjustment Factors .........................................................3-33 Table 4-1. Dredging Plant Cost Factors ......................................................................4-9

List of Figures

Figure 1-1. Methodology for Developing an Hourly Ownership and Operating

Rate for Construction Equipment..............................................................1-3 Figure 2-1. Equipment Rate Computation Worksheet ...............................................2-15 Figure 3-1. Total Hourly Rate Calculation for Overage Equipment............................3-25 Figure 3-2. Standby Hourly Rate Calculation for Overage Equipment.......................3-49 Figure 4-1. Months Available by Region......................................................................4-2 Figure 4-2. Dredging Plant Ownership and Operating Rate Worksheet ....................4-13

List of Appendixes Appendix A References .............................................................................................A-1 Appendix B Area Factors ...........................................................................................B-1 Appendix C Guide for Selecting Operating Conditions.............................................. C-1 Appendix D Equipment Hourly Calculation Factors................................................... D-1 Appendix E Economic Indexes for Construction Equipment ......................................E-1 Appendix F Tire Description and Tire Cost ................................................................F-1 Appendix G Tire Life and Tire Wear Factors ............................................................. G-1 Appendix H Manufacturer List ................................................................................... H-1 Appendix I Federal Cost-of-Money Rate.................................................................... I-1 Appendix J Equipment Accessories .......................................................................... J-1 Appendix K Ground Engaging Component Costs Included in Repairs (RCF)............K-1 Appendix L Guide for Estimating Drill Steel and Drill Bit Costs.................................. L-1 Glossary ...........................................................................................................Glossary-1 Index ..................................................................................................................... Index-1

EP 1110-1-8, Vol. 130 Nov 09

1-1

CHAPTER 1.0 - INTRODUCTION

1.1 Use

The use of this pamphlet is for rate determination on construction contracts, dredging contracts, and negotiated procurements and relates only to contractor-owned equipment. The overall intent of the pamphlet is to determine equipment costs that are fair and reasonable.

a. This pamphlet shall be used for determining hourly equipment rates that are contained in the independent government estimate.

b. In addition, the use of this pamphlet will be required by contractors for pricing contractor-owned equipment in negotiated procurements when:

(1) Cost or pricing data is not required, as defined in Federal Acquisition Regulation (FAR) Part 15.400, Contract Pricing.

(2) Cost or pricing data is required and the actual cost data to support either ownership or operating costs for equipment or equipment groups of similar model and series is not available.

(3) Cost or pricing data is required and available, but all or part of the data is determined not to be in accordance with the FAR cost principles.

1.2 Decision Flow Process

A flow chart (figure 1-1) is provided at the end of this chapter to help the user better understand the process for developing an hourly equipment rate. The flow chart shows the decision points that allow the user to decide whether to use the predetermined rate tables or calculate the rate using the method shown in figure 2-1 or using CHECKRATE (also see paragraph 3.4).

1.3 How to Obtain Assistance

When assistance is needed in understanding the methodology for calculating equipment rates, contact the Chief, Cost Engineering Branch, Engineering and Construction Division, Walla Walla District, U.S. Army Corps of Engineers, (CENWW-EC-X), 509-527-7511, 509-527-7510, or visit the Web site at http://www.nww.usace.army.mil/html/offices/ed/c/default.asp.

EP 1110-1-8, Vol. 130 Nov 09

1-2

1.4 How to Obtain CHECKRATE Spreadsheet

A Microsoft Excel® spreadsheet, named “CHECKRATE,” has been developed to calculate equipment rates using the methodology required by this pamphlet. The user must have Microsoft Excel® to run the application. The factors needed in the hourly cost calculations are located in the appendixes of this pamphlet. A copy of the spreadsheet may be obtained by choosing the CHECKRATE link on the following Web site: http://www.nww.usace.army.mil/html/offices/ed/c/default.asp.

1.5 How to Obtain this Publication

Volumes 1-12 of this pamphlet are available in portable document format (PDF) and can be viewed or downloaded at http://140.194.76.129/publications/eng-pamphlets. Copies of the pamphlet are also available on CD-ROM (Volumes 1-12) through the Superintendent of Documents or government bookstores (see appendix A). For additional information, telephone 202-512-1800, fax 202-512-2104, toll-free 866-512-1800, or access on the Internet at http://bookstore.gpo.gov/.

EP 1110-1-8, Vol. 130 Nov 09

http://140.194.76.129/publications/eng-pamphlets/

http://bookstore.gpo.gov/

Finished. The methodology in ths pamphlet should not be used for rental or leased equipment.

YES

YES

AVERAGE SEVERE

NO

YES

NO

DIFFICULT

Is the equipment contractor owned ?

Is the equipment in Table 2-1?

Is there equipment in Table 2-1 that is equivalent in configuration (size, capacity,

and horsepower) and value to the equipment for which you are determining a

rate?

Use the tables in chapter 2 for the actual or equivalent

equipment.

Is the equipment operating in average severe or difficult conditions? (see chapter 2, section II for definition)

Calculate a rate based on the step-by-step rate computation method shown in Figure 2-

1 or use CHECKRATE

Use the equipment rate shown in Table 2-1

From Table 2-2 use the arithmetic mean of the average and severe equipment rates.

(Note: if there is no severe rate for the equipment see guidance in chapter 2,

section II, paragraph 2-4.)

Use severe rate shown in Table 2-2. (Note: if there is no severe

rate for the equipment see guidance in chapter 2, section II,

paragraph 2-4.)

Is the use of this pamphlet required in accordance with Chapter 1, paragraph

1-1?

YES

NO

Use the contractor's actual cost and pricing data to determine a rate.NO

Figure 1-1. Methodology for Developing an Hourly Ownership and Operating Rate for Construction Equipment

START

Next Page

Is this land based or marine equipment?Land Based Equipment Marine equipment Use the methodology found in Chapter 4 for

determining a rate for Marine Equipment.

Is the equipment in Table 2-1 equivalent in configuration (size,

capacity, and horsepower) and value to the equipment for which you are

determining a rate?

YES

1-3

EP 1110-1-8, Vol. 130 Nov 09

NO

YES

NO

NO

FINISHED (except for standby)

YES

NO

Equipment is newer

If equipment is older than in Table 2-1 determine economic life by dividing LIFE by Working Hours Per Year. (see

chapter3 section II, Paragraph 3-11.a.)

Equipment is older

Equipment age does not exceed economic life Equipment age exceeds economic life

Is the Cost of Money Rate (CMR) different from that shown in chapter 2, section VII or Appendix B?

The Department of the Treasury adjusts the CMR (Prompt Payment Interest Rate) on or about 1 January and 1 July each year. For the current

Prompt Payment Interest Rate see http://www.publicdebt.treas.gov/opd/opdprmt2.htm.

If the cost of money rate shown in chapter 2, section VII, is not the current rate, the FCCM portion of the total hourly rate shall be adjusted. Adjust the Cost

of Money Rate per the instructions in chapter 3, section II, paragraph 3-7.

Is the cost of fuel 10% greater than or 10% less than the cost shown in Appendix B?

The contractor shall be required to furnish copies of all fuel supply contracts and invoices to the government to

support fuel cost adjustment. Request for upward adjustment in the rates will be considered only when fuel is supplied by recognized distributors of bulk quantities

If the contractor is able to furnish the above information, adjust the fuel cost per the instructions in chapter 3,

section II, paragraph 3-9.

If fuel costs are adjusted FOG costs also need to be adjusted by applying the same ratio used to adjust the

fuel cost.

Do the actual hours worked exceed 40 hours per week?

Make adjustments to the FCCM per the instructions in chapter 3,

section II, paragraph 3-8

Is the equipment's date of manufacure different from that in

Table 2-1 (see chapter 2 section 1, paragraph 2-2)?

Adjust the rate using Table 3-1 per the

instructions found in chapter3 section II, Paragraph 3-11.c.

Adjust the rate using Table 3-1 per the example found

in chapter3 section II, Paragraph 3-11.a.

Adjust the rate using Table 3-1 per the

instructions found in chapter3 section II,

Paragraph 3-12.

YES

Figure 1-1. Methodology for Developing an Hourly Ownership and Operating Rate for Construction Equipment

Continue from

previous page

1-4

EP 1110-1-8, Vol. 130 Nov 09

2-1

CHAPTER 2.0 - METHODOLOGY FOR CONSTRUCTION EQUIPMENT

SECTION I. GENERAL

2.1 Contents

This chapter provides the methodology used to compute the total hourly ownership and operating rates for construction equipment and marine equipment (except dredging plant). This detailed methodology includes the formulas and factors used to develop both total hourly rates and hourly standby rates. If the equipment is determined to be older than its estimated economic life (overage) or was purchased used, refer to chapter 3.

2.2 Basis for Equipment Rates

The hourly rates shown in table 2-1 reflect catalog list prices of equipment manufactured in 2006 (3 years old). List prices for equipment manufactured in years other than 2006 have been adjusted to a 2006 price level using economic indexes. Ownership and operating expenses are computed using area factors, found in appendix B, which are specific to each region and volume. This hourly rate methodology assumes that equipment furnished to the job is in sound, workable condition. Furthermore, the methodology applies only to equipment that prime contractors or subcontractors either own or control. These hourly rates and cost factors do not represent rental charges for those in the business of renting equipment.

2.3 Total Hourly Rate

Hourly rates for average conditions are shown in table 2-1 and are computed based on a 40-hour (hr) workweek. The hourly rate is the sum of ownership and operating costs. Table 2-2 contains all individual rate elements for both average and severe conditions. An example of the methodology used to compute the total hourly rate is shown in figure 2-1. For standby calculation, see section IX.

a. Ownership Cost Elements. The ownership portion of the rate consists of an allowance for depreciation (DEPR) and facilities capital cost of money (FCCM).

b. Operating Cost Elements. Operating costs include allowances for the following:

• Fuel • Filters, oil, and grease (FOG) (includes servicing) • Repairs (includes maintenance and major overhauls)

EP 1110-1-8, Vol. 130 Nov 09

2-2

• Tire wear (replacement) • Tire repair

c. Exclusions to Hourly Rates. Total hourly rates for owning and operating equipment do not include allowances for the following:

• Operating labor • Mobilization and demobilization • Field office overhead expenses • Home office or general and administrative (G&A) overhead expenses • Investment tax credit • Contingency allowance • Profit • Parts and labor escalation

It should also be noted that replacement cost is not included in the rates, as it is not an allowable item of cost per FAR 31.105(d)(2)(i).

d. Other Ownership Elements. The following elements of cost are not included in the total hourly rates. These costs are allowable and would normally be included in the contractor’s field office or home office overhead rate calculation.

(1) License fees, property taxes, storage, and insurance costs are considered indirect costs and are not included in the total hourly rates.

(2) Jobsite security, inspection fees, recordkeeping, mechanic training, and highway permits are also not included in the total hourly rates.

SECTION II. OPERATING CONDITIONS

2.4 Average, Difficult, or Severe Conditions

Operating conditions may be average, difficult, or severe. Hourly rates for both average and severe operating conditions are determined in accordance with appendix C. The rate for the difficult condition is the arithmetic mean of the average and the severe rates. When only the average rate is shown in table 2-2, the rate applies for all operating conditions or as determined by the contracting officer. Average condition rates are included in both tables 2-1 and 2-2. Only table 2-2 contains the severe condition rates.

EP 1110-1-8, Vol. 130 Nov 09

2-3

2.5 Determination of Condition

For contract modifications, the contracting officer determines the equipment operating condition to be used. This determination is based on contract specifications, site conditions, basis of any supporting evidence, and guidance in appendix C. Evaluation of operating conditions for equipment not listed in appendix C will be consistent with examples shown in appendix C. The operating condition of the equipment relates to the average and severe factors as detailed in appendix D.

SECTION III. EQUIPMENT SELECTION

2.6 General

Equipment shown in table 2-1 is representative of equipment that is used in general construction. Note that some equipment may require additional attachments or accessories. Each unit of equipment is grouped into a main group called a category (CAT) and a subgroup called a subcategory (SUB). This type of grouping is displayed in table 2-1 and appendix D. Also, an identification number (ID No.) is assigned to each unit of equipment. The ID No. consists of three parts. The first three characters are the CAT, the second two characters are the manufacturer's code, and the last three characters are the sequence number.

2.7 Truck Selection

Because of the large number of possible combinations of highway truck chassis and bodies, both are listed separately. For estimating purposes, use the gross vehicle weight (GVW) rating of the truck chassis to make a selection with the following conditions:

a. The combined weight of the truck chassis, truck body, and payload must not exceed the GVW rating shown for the truck chassis.

b. The gross combined weight (GCW) of the truck, trailer, and payload must not exceed the GCW rating shown.

2.8 Crawler Tractor Selection

A wide range of combinations of ripper and various blade options are available for each crawler tractor. For ease of use, all tractors include a universal blade attachment. Other blade and ripper attachments are shown separately and should be substituted for the universal blade to match actual equipment configuration. Only the hourly expense for those attachments that are required to perform the work shall be allowed.

EP 1110-1-8, Vol. 130 Nov 09

2-4

2.9 Equipment Accessories

Equipment accessories included on the major pieces of equipment in table 2-1 are listed in appendix J.

SECTION IV. EQUIPMENT VALUE

2.10 List Price and Accessories

The total list price includes those accessories normally purchased by the contractor plus required safety features.

2.11 Discount Code (DC)

A 7.5-percent discount is used for all equipment except highway trucks that are discounted at 15 percent. The total discounted price is derived by subtracting the appropriate discount from the total list price. The identification of the discount is shown in appendix D under column heading DC. Two codes are used to identify the discount, B equals the basic discount of 7.5 percent and S equals the special discount of 15 percent.

2.12 Sales or Import Tax

Total state sales tax (which includes local taxes) or import tax is computed as a percentage of the discounted price. The average tax for the region is shown in appendix B.

2.13 Freight

Estimated allowances for freight are provided in appendix B. This allowance includes preparation and delivery. Multiply the shipping weight based on hundredweight (cwt) by the freight rate to determine freight charges.

2.14 Total Equipment Value (TEV)

Freight is added to the total discounted price (which includes sales tax) to arrive at the TEV. The estimated TEV is indicated in table 2-1 under the column heading VALUE.

EP 1110-1-8, Vol. 130 Nov 09

2-5

SECTION V. LIFE

2.15 Economic Life (LIFE)

The expected economic life of the equipment will vary based on the type of equipment and the condition of use. It is established from manufacturers’ or equipment associations’ recommendations. The expected economic life in hours is given in appendix D, under the column heading LIFE, for both average and severe conditions.

2.16 Working Hours Per Year (WHPY)

Annual average operating hours have been established for equipment working within the region covered by this pamphlet. The number of WHPY as shown in appendix B is equivalent to 1 year’s use for a single shift operation. Average annual hours of use per year are determined by reducing the maximum available hours per year (40 hours per week, 52 weeks per year) to allow for lost working days due to the following factors:

• Weather • Employee holidays • Equipment maintenance and repairs • Mobilization and demobilization • Miscellaneous downtime

SECTION VI. SALVAGE VALUE

2.17 Salvage Value (SLV)

The salvage value for equipment is based on advertisements of used equipment for sale as displayed in current engineering and construction magazines, manufacturer’s recommendations, and the Green Guide Volumes I and II, Handbook of New and Used Construction Equipment Values, Equipment Watch.

2.18 Salvage Value Percentage

The salvage value percentage used for each type of equipment is listed in appendix D under the heading SLV as a percentage of the equipment value. It is equal for both average and severe conditions.

EP 1110-1-8, Vol. 130 Nov 09

SECTION VII. OWNERSHIP COST

2.19 Ownership Elements

The ownership portion of the rate consists of allowances for depreciation (DEPR) and facilities capital cost of money (FCCM). These two cost elements are computed based on the TEV. Other ownership elements may be allowed (see paragraph 2-3.d.). Total ownership rate per hour is expressed by formula, as follows:

Ownership Rate/hr = DEPR/hr + FCCM/hr

2.20 Depreciation

The straight-line method is used to compute depreciation.

a. For rubber-tired equipment, the tire cost index (TCI) must first be calculated to complete the depreciation formula.

b. Hourly depreciation is calculated by dividing the “depreciable" value (TEV less estimated salvage and tire cost) by the expected economic life of the unit of equipment in hours. Expressed by formula, depreciation cost equals the following:

( )( )[ ] ( )( )[ ][ ]LIFE

Cost TireTCI - SLV-1TEV DEPR/hr =

Where:

(1) TEV is the total equipment value found in table 2-1.

(2) SLV is the salvage value from appendix D.

(3) TCI is the tire cost index, which is determined by dividing the year of manufacture tire index by the present-year tire index. For table 2-1, the present year is 2009 and the year of manufacture is 2006 (3 years old). These indexes are listed as part of appendix E [see Economic Key (EK) 100, All Tires and Tubes].

(4) Tire cost is the total tire and/or conveyor belt cost. The total tire cost is the sum of the cost of all front, drive, and trailing tires. The tire cost for rubber-tired equipment is based on tire values at the time the equipment was manufactured.

(5) The LIFE is the economic life, which is based on the number of operating hours throughout the economic life of the equipment (see paragraph 2-15). Hours for LIFE are provided in appendix D.

2-6

EP 1110-1-8, Vol. 130 Nov 09

2.21 Facilities Capital Cost of Money (FCCM)

The FCCM, as defined in FAR 31.205-10, is included in the total hourly rates. This cost is computed by multiplying a discounted cost of money rate (CMR) by the average value of equipment and prorating the result over the annual operating hours. The January 2009 CMR [5.625 percent as shown in appendix I determined by the Secretary of the Treasury pursuant to Public Law 92-41 (85 Stat. 97)] is discounted by a reduction of 25 percent to avoid duplication when applying estimated markups for overhead and profit. The discounted CMR is then 4.50 percent. The Department of the Treasury adjusts the CMR on or about 1 January and 1 July each year; these revisions are printed in the Federal Register or can be found on the Internet at http://www.treasurydirect.gov/govt/rates/tcir/tcir_opdprmt2.htm. The CMR should be adjusted to the actual period that the equipment is used. Expressed by formula, FCCM cost equals the following:

( )( )( )(WHPY)

CMR discountedAVFTEV FCCM/hr =

Where:


(2) ( )( )[ ][ ] 2N /2 SLV 11-N (AVF) Factor Value Average ++= .

(a) Number of Years (N) in Depreciation Period = LIFE/WHPY.

(b) LIFE is the economic life, which is based on the number of operating hours throughout the economic life of the equipment (see paragraph 2-15). Hours for LIFE are provided in appendix D.

(3) Discounted CMR = 5.625% (Jan – Jun 2009 rate) / 1.25 = 4.50%.

(4) WHPY = Working hours Per Year found in appendix B.

SECTION VIII. OPERATING COST

2.22 Operating Cost Elements

The total operating cost is the sum of the following five elements: fuel, FOG, repairs, tire wear, and tire repair.

2-7

EP 1110-1-8, Vol. 130 Nov 09

2.23 Fuel Cost

Fuel costs are computed for each gas, diesel, or electric engine. When the unit of equipment has two engines, as in the case of a truck crane, this methodology treats each engine separately for fuel costs. The hourly fuel cost for each unit of equipment is shown under the column heading FUEL in tables 2-1 and 2-2. When the unit of equipment has no engine, no fuel cost will be shown. Hourly fuel costs are calculated for each engine, as expressed in the following formula:

Fuel Cost/hr = Horsepower (hp) x Fuel Cost/Gallon (gal) x Fuel Factor (gal/bhp-hr)

a. Horsepower is the engines rated horsepower. All horsepower ratings for engine-driven equipment are listed with the equipment description in table 2-1.

b. Fuel Cost/Gallon is based on values shown in appendix B. See chapter 3 for fuel cost adjustments.

c. Fuel Factor - Gas or Diesel Fuel. The fuel factor in gallons per brake horsepower-hour (bhp-hr) is listed in appendix D for both average and severe conditions. Fuel factors are also listed for both the engine powering the main equipment (prime engine) and the engine providing power to the carrier vehicle. For severe conditions, the fuel consumption rate is 30 percent greater than the average condition rate. Gas or diesel fuel factors are computed by using the following formula:

Gal per Fuel of lbshr-bhp per Fuel lbs x (HPF) Factor Horsepower hr)-(Gal/bhp Factor Fuel =

Where:

(1) The HPF is the horsepower factor used in the fuel and electricity consumption formulas and represents an average percent of full-rated horsepower being used by the engine. The fuel consumption factors, which are shown in appendix D under column headings Fuel Factor-Equipment and Fuel Factor-Carrier, are computed based on the HPF shown under these column headings. This HPF is an estimate of the engine load under average working conditions. It is necessary to modify the rated horsepower as engines and motors in actual production do not work at their full-rated horsepower at all times. Periods spent at idle, travel in reverse, traveling empty, close maneuvering at part throttle, and operating downhill are examples of conditions that reduce the HPF. Professional judgment regarding cycle time and equipment loading is applied to determine this average HPF. Normal field application can also vary according to: operator efficiency, type of material, type of work cycle, and overall jobsite efficiency. This pamphlet provides an estimated average HPF, not a specific factor.

2-8

EP 1110-1-8, Vol. 130 Nov 09

(2) Pounds (lbs) fuel per bhp-hr is an average based on a variety of engine applications from manufacturer engine data. The following represent an average of the normal application of equipment and are indicative of engine fuel consumption industry wide. Pounds fuel (consumed) per bhp-hr is based on the following averages and is used consistently throughout this pamphlet:

Gasoline = 0.55 lbs per bhp-hr Diesel = 0.34 lbs per bhp-hr

(3) Pounds fuel per gallon is the factor that determines the weight of the fuel consumed. The following are used as constants in this pamphlet:

Gasoline = 6 lbs per gal Diesel = 7 lbs per gal

d. Fuel Factor - Electricity. Assuming that an electric motor uses 1 kilowatt (kW) per horsepower (considering all inefficiencies), and using the same HPF for gas or diesel fuel consumption, the electricity consumption is computed by the following formula:

hr-hpelectric per kW 1 x HPF (kW/hr) Factor Fuel =

e. Fuel and Electricity Cost. The cost per gallon for gasoline and diesel fuel used to compute the hourly fuel cost is shown in appendix B. The hourly fuel cost for all gasoline-powered equipment, diesel-powered highway trucks, and truck crane carriers includes an allowance for Federal and state road taxes, sales taxes, and rental for fuel storage tanks and pumps. Cost per kilowatt-hour used to compute electricity cost are also shown in appendix B.

2.24 Filters, Oil, and Grease (FOG) Cost

The FOG cost is computed as a percentage of the hourly fuel costs.

a. The FOG contains items of cost for routine servicing of the equipment, which includes the following:

• Base wages for servicing labor • Fringe benefits and labor burden costs for servicing • Service truck, tools, and fuel truck allowance • Shop allowance when shop servicing is required • Other equipment costs for servicing • FOG material allowance • Taxes and shipping for FOG supplies • Handling and disposal of hazardous materials and oil

2-9

EP 1110-1-8, Vol. 130 Nov 09

b. The hourly FOG cost is calculated for each engine using the following formula:

LAF x Cost/hr Fuel x Factor FOG Cost/hr FOG =

Where:

(1) The FOG Factor is the percent allowance expressed as a decimal factor under each fuel type heading E (electricity), G (gas), or D (diesel). See appendix D.

(2) Fuel cost/hr is a calculated value shown under the column heading FUEL in tables 2-1 and 2-2.

(3) The LAF (labor adjustment factor) is a decimal factor to account for regional variations in labor and parts costs. This factor is provided in appendix B.

c. The FOG percentage allowance includes the cost for servicing. For equipment that is normally serviced by an oiler assigned to the unit of equipment, the FOG percentage is reduced. This reduction applies to the following equipment: cranes, draglines, hydraulic excavators, and shovels (except equipment under category numbers C75, C80.01, C85.11, C85.12, C85.21, C90.01, H25.11, H25.12, H30.01, H30.02, and M10.32).

d. When a unit of equipment has no engine (therefore no fuel costs calculated) and the equipment requires some type of fuel (i.e., propane, kerosene), an alternative hourly fuel and FOG allowance may be used in lieu of the regularly calculated fuel and FOG hourly costs. A FOG allowance may also be added when the equipment has no engine and has parts that require FOG. The alternative fuel allowance is added to the alternative FOG allowance for a total alternative fuel and FOG cost. (See figure 2-1, 5.c.)

2.25 Repair Cost

a. The repair cost accounts for equipment repairs, maintenance, and major overhauls (including undercarriage wear, ground engaging tools, and designated attachments) performed in either the field or the shop. Where tire cost is the cost of the tires when the equipment was manufactured, use the same TCI and tire cost as shown in the depreciation calculation (see section 2-20). The estimated hourly rate for repairs is computed as follows:

LIFERF x Cost)]] e[(TCI)(Tir-[(TEV) Cost/hr Repair =

2-10

EP 1110-1-8, Vol. 130 Nov 09

Where:


(2) TCI is the tire cost index, which is determined by dividing the year of manufacture tire index by the present-year tire index. For table 2-1, the present year is 2009 and the year of manufacture is 2006 (3 years old). These indexes are listed as part of appendix E [see Economic Key (EK) 100, All Tires and Tubes].

(3) Tire cost is the total tire and/or conveyor belt cost. The total tire cost is the sum of the cost of all front, drive, and trailing tires. The tire cost for rubber-tired equipment is based on tire values at the time the equipment was manufactured.

(4) Repair factor (RF) is calculated as follows:

LAF x EAF x RCF RF =

Where:

(a) The RCF (repair cost factor) is shown in appendix D. This factor varies depending on the operating condition of the equipment (average or severe).

(b) The EAF (economic adjustment factor) is used to adjust the RCF to current price levels. The EAF is equal to the economic index for the present year divided by the economic index for the year of manufacture. Indexes listed in appendix E are used to develop the EAF. Economic indexes are determined as follows:

Economic Index for the Present Year. This is the economic index for the present year (2009 for table 2-1 calculations). Obtain the economic index from appendix E. The index is located in the column with the present year and the row with the type of equipment in question. When the column for the present year has not been included, the index can be estimated using a straight-line projection.

Economic Index for the Year of Manufacture. This is the economic index for the year the equipment was manufactured (2006 for table 2-1 calculations). Obtain the economic index from appendix E. The index is located in the column with the year of manufacture and the row with the type of equipment in question. When the actual age of the equipment is beyond the last year of its economic life, the equipment is considered overage. Economic life is determined by dividing hours of LIFE (from appendix D) by WHPY (appendix B).

(5) The LIFE is the economic life, which is based on the number of operating hours throughout the economic life of the equipment (see paragraph 2-15). Hours for LIFE are provided in appendix D. 2-11

EP 1110-1-8, Vol. 130 Nov 09

b. Items Included in the Repair Cost Factor. The estimated percentage allowances for the RCF are shown in appendix D under the column heading RCF and are expressed as decimal factors. These RCFs (for both the average and severe conditions) compensate for the following cost elements:

(1) Mechanic’s labor includes base wages, fringe benefits, supervision, travel, and all other costs for labor associated with craft workers engaged in the direct repair of equipment either in the field or the shop.

(2) Repair parts and supplies include those items that are required for all repairs and major overhauls complete with applicable sales taxes and freight charges.

(3) Service trucks and other equipment used during field or shop repair and maintenance work including tools.

(4) Supporting repair facilities include field and main repair shops, complete with parts and supplies inventory, and shop overhead.

2.26 Tire Wear Cost

a. Tires included on rubber-tired equipment are generally the type and ply rating recommended as standard tires by the equipment manufacturer. Tire costs include both tire wear (replacement) and tire repair as individual elements of cost. Conveyor belt wear is also included under this cost element. The belt wear is treated like tire wear. The wear factors are listed in the front tire wear factor column in appendix D. Belt life and cost are listed in appendix F.

b. The formula for calculating tire wear applies to each tire position: front (FT), drive (DT), and trailing (TT). However, all tires performing the drive function are considered drive tires and are listed in the drive position. The total hourly tire wear cost for each unit of equipment is the sum of the hourly cost for each position. The total hourly tire wear cost equals the current cost of new tires plus the cost of one recapping divided by the expected life of the new tires plus the life of the recapped tires. This hourly allowance for determining tire wear cost is expressed in the following formula:

Life Tire Maximum x Factor WearTire x Factor Life TireCost Tire Current x Factor Cost Tire Cost/hr WearTire =

2-12

EP 1110-1-8, Vol. 130 Nov 09

Where:

(1) Tire Cost Factor is estimated at 1.5, which represents the purchase of the original tire plus one recap. It has been estimated that a recap costs approximately 50 percent of the new tire cost.

(2) Current Tire Cost is the estimated cost that applies to all tires on the equipment in that position. For example, four new drive tires valued at $500 each would result in an amount of $2,000 for total drive tire cost. The size and cost of each tire used in the pamphlet are listed for information in appendix F.

(3) Tire Life Factor is estimated at 1.8, which represents the original tire life plus one recap. It has been estimated that a recap lasts approximately 80 percent of the life of a new tire.

(4) Tire Wear Factor is based on the position of the tire, type of equipment, and condition of use. Tire wear factors have been developed and are listed in appendix D. These factors will provide a percentage reduction to the maximum tire life. Appendix G contains the methodology used to develop these factors and a computation example for a rear dump wagon.

(5) Maximum Tire Life expressed in hours is shown for various new tire types in appendix F. The tire life is estimated from information provided by Goodyear Tire and Rubber Company and by using the method and tables in Production and Cost Estimating of Material Movement with Earthmoving Equipment, Terex Corporation, Hudson, Ohio.

2.27 Tire Repair Cost

It has been estimated that tire repairs are 15 percent of the total hourly tire wear cost. The LAF is used to adjust the tire repair cost to account for regional variations in labor and parts costs. This cost element has been calculated and listed separately in table 2-2. It is expressed as a formula as follows:

LAF x 0.15 x Cost WearTireHourly Total Cost Repair Tire =

2-13

EP 1110-1-8, Vol. 130 Nov 09

SECTION IX. STANDBY HOURLY RATE

2.28 Standby Hourly Rate

The standby rate is computed by allowing the full FCCM hourly cost (based on a 40 hour workweek) plus one-half of the hourly depreciation. It is expressed as a formula, as follows:

( ) FCCM/hr 0.50 x DEPR/hr Rate/hrStandby +=

a. Paid standby shall not exceed 40 hours per week (7 calendar days) (based on a 40 hour workweek) per unit of equipment. Actual operating hours during a week will be credited against the 40 hours maximum standby allowance.

b. Standby costs will not be allowed during periods when the equipment would have otherwise been in idle status.

c. When the equipment is purchased used, standby will be computed on the basis that the equipment was purchased new by the contractor in the year it was actually manufactured. Refer to chapter 3 for rate adjustments.

SECTION X. RATE CALCULATION EXAMPLE

2.29 Computation Example

Figure 2-1 is an example of how the total hourly rates in table 2-1 are computed. A blank Equipment Rate Computation Worksheet is included in appendix A and can be copied as needed.

a. When an hourly rate for a specific unit of equipment is not included in this pamphlet and a rate must be computed, the methodology contained in chapter 2 shall be followed. However, when a unit of equipment is not included in this pamphlet and the necessary factors to compute a rate are not found in appendix D, please contact the Chief, Cost Engineering Branch, Engineering and Construction Division, Walla Walla District, U.S. Army Corps of Engineers, for assistance as explained in chapter 1. A Microsoft Excel® spreadsheet (CHECKRATE) is also available for rate computation (see chapter 1).

b. See chapter 3 for further guidance on the procedure for rate adjustments.

2-14

EP 1110-1-8, Vol. 130 Nov 09

1. EQUIPMENT INFORMATION AND EXPENSE FACTORS

a.(1)

(2) HC-238H II(3) 2009(4) 2006(5) 284(6) 430(7)

3 D-off

4 D-on(8) 1,913 cwt(9)

Size/Ply App F Code No. Unit Price Cost(a) Front (FT): 14-25/20 ANMB1 4 $1,206 $4,824(b) Drive (DT): 14-25/20 ANMB1 8 $1,206 $9,648(c) 0 $0 $0(d) $14,472

(10)$1,575,295 $0

b. 0.04c.

(1) 20(2) A AVERAGE(3) B 0.075(4) 20,000(5) 0.20(6) 0.024(7) 0.005(8) 0.110(9)

(a) 0.66(b) 0.58(c) 0.73

(10) 0.90

Use this worksheet to compute an hourly rate for equipment that is not in this pamphlet or is in the pamphlet but not equivalent in size, capacity, horsepower, or value (see appendix A for blank form).

Region 01

ID No: C90LB001

Example: The piece of equipment shown in this example is based on a known piece of equipment for illustration purposes only.

Tire Wear Factor:

Repair Cost Factor (RCF):

Front (FT):Drive (DT):Trailing (TT):

Filter, Oil, and Grease (FOG) Factor (E G D):

Economic Key (EK):

Trailing (TT):

Life in Hours (LIFE):Salvage Value Percentage (SLV):

Total Tire Cost:

Fuel Factor - Carrier (E G D):

Discount Code (DC): B = 7.5% (0.075) or S = 15.0% (0.15)

Fuel Factor - Equipment [Electric (E) Gas (G) Diesel (D)]:

OR actual purchase price:

Category and Subcategory Number:USE APPENDIX D TO COMPLETE THE FOLLOWING DATA:

List Price + Accessories: [at Year (yr) of Manufacture]

Hourly Expense Calculation Factors:

Condition (C): A=Average D=Difficult S=Severe

C90

Horsepower - Carrier:

Shipping Weight (cwt):

- Equipment: 0-None; 1-electric; 2-gasoline;3-diesel off-road; 4-diesel on-road; 5-marine gas;6-marine diesel

- Carrier: 0-None; 1-electric; 2-gasoline; 3-diesel off-road; 4-diesel on-road; 5-marine gas;6-marine diesel

Fuel type:

Tire size and number of tires: (Cost of tires based on present year, see 1.a.(3) and App. F):

Enter number from0 to 6 ==>

Enter number from0 to 6 ==>

Equipment Description:

Model and Series:

CRANES, MECHANICAL, LATTICE BOOM, TRUCK MTD, 150 TON / 260' BOOM, 8X4

Horsepower - Equipment:

Present Year or Year of Use:Year Manufactured:

Equipment Specification Data:

Figure 2-1. Equipment Rate Computation Worksheet Page 1 of 6

EP 1110-1-8, Vol. 130 Nov 09

2-15

2.

a. = $1,575,295

(1) Discount: (List Price + Accessories) x {1.a.(10)} {1.c.(3)}

($1,575,295 + $0.00) x 0.075 = -($118,147)

(2) $1,457,148

(3) Sales or Import Tax: Subtotal x Tax Rate {2.a.(2)} {'Appendix B}

$1,457,148 x 6.00% = $87,429

(4) $1,544,577

b. x{1.a.(8)} {Appendix B}

1,913 cwt x $9.14 /cwt = $17,485

c. TOTAL [2.]: = $1,562,062

3.

a. LIFE / {1.c.(4)} {Appendix B}

20,000 hr / 1,360 hr/yr = 14.71 yrs (N)

4.

a.

(1) Tire Cost Index (TCI):

Tire Index, Year of Manufacture,

{1.a.(4)} / =Tire Cost

Index (TCI) Appendix E, EK=100

2926 / 3382 = 0.865

(2) [TEV x (1.0-SLV) - (TCI x Tire Cost)] / LIFE{2.c.} {1.c.(5)} {4.a.(1)} {1.a.(9)(d)} {1.c.(4)}

[$1,562,062 x (1.0-0.20) - ( 0.865 x $14,472 )] / 20,000 hrs = $61.86 /hr

OWNERSHIP COST

Region 01

Freight:

EQUIPMENT VALUE


Discount Code

Subtotal {2.a.} - {2.a.(1)}

Total Discounted Price: Subtotal: 2.a.(2) + 2.a.(3)

Subtotal =

{2.a.(4)} + {2.b} OR actual purchase price {1a.(10)}

Depreciation

(See chapter 3 for used and overage equipment rate adjustments.)

Subtotal =

Appendix E, EK=100

Working Hours Per Year (WHPY) = N

Shipping WeightFreight Rate per

cwt

TOTAL EQUIPMENT VALUE (TEV):

Tire Index, Present Year or Year of Use, {1.a.(3)}

DEPRECIATION PERIOD (N)


EP 1110-1-8, Vol. 130 Nov 09

2-16

4. OWNERSHIP COST (Continued)

b. Facilities Capital Cost of Money (FCCM):

(1) [( N - 1.0 ) x (1.0 + SLV) + 2.0] / (2.0 x N) =Avg Value

Factor{3.a.} {1.c.5.} {3.a.} (AVF)

[(14.71 yr - 1.0) x (1.0 + 0.20) + 2.0] / (2.0 x 14.71 yr) = 0.627

(2) TEV x AVF xAdjusted

Cost-of-Money / WHPY

{2.c.} {4.b.(1)} {Appendix B} {Appendix B}

$1,562,062 x 0.627 x 3.90% / 1,360 hr/yr = $28.09 /hr

c. TOTAL HOURLY OWNERSHIP COST: TOTAL [4.]: = $89.95 /hr

{4.a.(2)} + {4.b.(2)}

5. OPERATING COST

a. Fuel Costs:

(1) Equipment:

Fuel Factor x Horsepower (hp) xFuel Cost per Gallon (gal)

{1.c.(6)} {1.a.(5)} {Appendix B}

0.024 x 284 hp x $3.17 /gal = $21.61 /hr

(2) Carrier:{ 1.c.(4)}

Fuel Factor x Horse power (hp) x Fuel Cost per gal{1.c.(7)} {1.a.(6)} {Appendix B}

0.005 x 430 hp x $3.71 /gal = $7.98 /hr

(3) Total Hourly Fuel Cost: Total [5.a.] = $29.59 /hr{5.a (1)} + {5.a (2)}

b. FOG Cost:

(1) Equipment:

FOG Factor xEquipment Hourly

Fuel Cost xLabor Adjustment

Factor (LAF){1.c.(8)} {5.a.(1)} {Appendix B}

0.110 x $21.61 /hr x $ 1.12 /hr = $2.66 /hr

Region 01


EP 1110-1-8, Vol. 130 Nov 09

2-17

5.

(2) Carrier:

FOG Factor xCarrier Hourly

Fuel Cost x LAF {1.c.(8)} {5.a.(2)} {Appendix B}

0.110 x $7.98 /hr x 1.12 = $0.98 /hr

(3) Total [5.b.] = $3.64 /hr

c. Total [5.c.] = $0.00 hr

d.

(1)EK is from {1c. (1)}

/

6905 / 6543 = 1.055

(2) Repair Factor (RF):

RCF x EAF x LAF{1.c.(10)} {5.d.(1)} {Appendix B}

0.90 x 1.055 x 1.12 = 1.063

(3) Repair Cost:

[TEV - (TCI x Tire Cost)] x RF / LIFE {2.c.} {4.a.(1)} {1.a.(9)(d)} {5.d.(2)} {1.c.(4)}

[$1,562,062 - (0.865 x $14,472)] x 1.063 / 20,000

(4) Total [5.d.] = $82.36 /hr

(See table 3-1 for last year of economic life.)

Total Hourly Repair Cost:

Appendix E, EK={1.c.(1)} Appendix E, EK={1.c.(1)}

(See chapter 2, paragraph 2.24.d. for guidance on when to use.)

Repair Cost:

Economic Index, Present Year or Year of Use,{1.a.(3)}

Economic Index, Year of Manufacture, {1.a.(4)}

Economic Adjustment Factor (EAF):

OPERATING COST (Continued)

Region 01

Total Hourly FOG Cost:

Alternative Fuel/FOG Cost:

{5.b.(1)} + {5.b.(2)}


EP 1110-1-8, Vol. 130 Nov 09

2-18

5.

e.

(1) Front Tires (FT):

(1.5 x FT Cost) / (1.8 x FT Wear Factor x Maximum Tire Life Hours){1.a.(9)(a)} {1.c.(9)(a)} {Appendix F}

(1.5 x $4,824) / (1.8 x 0.66 x 2,500 hr) = $2.44 /hr

(2) Drive Tires (DT):

(1.5 x DT Cost) / (1.8 x DT Wear Factor x Maximum Tire Life Hours){1.a.(9)(b)} {1.c.(9)(b)} {Appendix F}

(1.5 x $9,648) / (1.8 x 0.58 x 2,500 hr) = $5.54 /hr

(3) Trailing Tires (TT):

(1.5 x TT Cost) / (1.8 x TT Wear Factor x Maximum Tire Life Hours){1.a.(9)(c)} {1.c.(9)(c)} {Appendix F}

(1.5 x $0.00) / (1.8 x 0.73 x 0 hr) = $0.00 /hr

(4) Total Tire Wear Cost: Total [5.e.] = $7.98 /hr

f.

Total Tire Wear Cost per Hour x (0.15 x LAF)

{5.e.(4)} {Appendix B}

$7.98 /hr x (0.15 x 1.12) Total [5.f.] = $1.34 /hr

g. Total [5.] = $124.91 /hrTOTAL HOURLY OPERATING COST:

Sum {5.e.(1)} through {5.e.(3)}

Sum {5.a.} through{ 5.f.}

Region 01


Tire Repair Cost:

Tire Wear Cost: (Use current price levels. See Appendix F.)


EP 1110-1-8, Vol. 130 Nov 09

2-19

6.

a.

+ Operating Cost{4.c.} {5.g.}

$89.95 /hr + $124.91 /hr = $214.86 /hr

b.

Depreciation + (FCCM x 40 hr/wk / Work hr/wk) + Operating Cost

{4.a.(2)} {4.b.(2)} {5.g.}

$61.86 /hr + ($28.09 /hr x 40 hr/wk / 60 hr/wk) + $124.91 /hr = $205.50 /hr

c.

(Depreciation x 0.50) + FCCM {4.a.(2)} {4.b.(2)}

($61.86 /hr x 0.50) + $28.09 /hr = $59.02 /hr

Standby Hourly Rate:

(Refer to Chapter 2, paragraph 2.28 for guidance on use.)

See Chapter 3 if rate adjustments are necessary.

(Refer to Chapter 3, paragraph 3.12 for guidance for overage equipment.)

Region 01

Other Work Shifts Hourly Rate:

example:60 hr/wk

(example:60 hr/wk)

HOURLY RATES

Total Hourly Rate: [based on 40 hours per week (wk)]

(Refer to Chapter 3, Adjustments to Rates, for methodology.)

Ownership Cost


EP 1110-1-8, Vol. 130 Nov 09

2-20

Table 2-1. Hourly Equipment Ownership and Operating Expense

EXPLANATION OF TABLE HEADINGS

Example unit of equipment: Link Belt, Model HC-238H II, 150 Ton, 260’-boom.

CAT: C90 is the category number and identifies it as Cranes, Mechanical, Lattice Boom, Truck Mounted (from appendix D). ID No.: C90LB001 is the unique identification number for the above Link Belt crane. AM equals the manufacturer (see appendix H). 001 equals the numeric order of this unit of equipment within the manufacturer’s listing. MODEL: HC-238H II is the equipment model number. EQUIPMENT DESCRIPTION: Specific information for each particular unit of equipment is described, such as “150 ton with a 260-foot boom” for the Link Belt crane. ENGINE HORSEPOWER AND FUEL TYPE: The amount of horsepower and type of fuel used is stated for the main and carrier engines. The Link Belt crane carrier has a 430-horsepower engine, and the crane has a 207-horsepower engine. Both engines are diesel (D). VALUE (TEV): This column reflects the predetermined “equipment cost” used to compute the rates and is based on equipment purchased new in 2006. TOTAL HOURLY RATES ($/HR): All ownership and operating expenses for the average condition are included. All cost elements, including fuel, are totaled in the AVERAGE column. The STANDBY column includes the hourly allowance for equipment on legitimate standby status (see section 2-27 for more information). ADJUSTABLE ELEMENTS: This column shows ownership elements and fuel costs used to develop the average total hourly rates so they can be adjusted as indicated in chapter 3. Operating costs may be determined by subtracting the ownership cost elements (DEPR plus FCCM) from the total hourly rate for the average condition. CWT: The shipping weight of the equipment is stated in hundredweight.

2-21

EP 1110-1-8, Vol. 130 Nov 09

2-21

TOTAL HOURLY RATES ($/HR)

VALUE (TEV)

2006 ($)MODEL EQUIPMENT DESCRIPTION MAIN

ENGINE HORSEPOWER AND FUEL TYPE

AVERAGE STANDBY DEPR FCCM FUEL CWTID.NO. CARRIER

ADJUSTABLE ELEMENTS

Table 2-1. HOURLY EQUIPMENT OWNERSHIP AND OPERATING EXPENSE1REGION

EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

AGGREGATE / CHIP SPREADERSA100.10 SELF-PROPELLEDSUBCATEGORY

ROSCO, A LeeBoy COMPANY

152SPRHA10RS003 $108,142 10.59 2.07 16.38 1497.3743.82CHIP SPREADER, SELF PROPELLED, 10' WIDE, 1.70 CY, 2WD

HP D-off


HP D-off


HP D-off


HP D-off


HP D-off

205SPREADPROA10RS008 $213,845 21.05 4.10 22.09 15814.6375.13CHIP SPREADER, SELF PROPELLED, 16' WIDE, 4.50 CY, 4WD

HP D-off

0.20 TOWED & TAILGATESUBCATEGORY

AMERICAN ROAD MACHINERY, INC.

TG-505CA10AR001 $3,019 0.40 0.06 0.00 50.260.83CHIP SPREADER, TAILGATE, 8' WIDE (ADD DUMP TRUCK)

ODELL 900A10AR002 $14,636 1.95 0.29 0.00 221.274.25CHIP SPREADER, TOWED, 8' WIDE, 3 CY (ADD DUMP TRUCK)

SEALMASTER, INC.

R-1 E2310A10SE001 $12,611 1.68 0.25 0.00 211.093.49CHIP SPREADER, TAILGATE, 8' WIDE, 1.13 CY (ADD DUMP TRUCK)

EP 1110-1-8, Vol. 130 Nov 09

2-22


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

A10 SEALMASTER, INC. (continued)R-1 E2500A10SE002 $14,818 1.98 0.29 0.00 301.284.11CHIP SPREADER, TOWED, 8' WIDE, 1.13

CY (ADD DUMP TRUCK)

AIR COMPRESSORS, PORTABLEA150.10 ROTARY SCREWSUBCATEGORY

INGERSOLL RAND ROTARY-REC COMPRESSOR DIV

56P175WJDA15IA001 $22,073 1.74 0.41 6.39 211.2811.61AIR COMPRESSOR, 175 CFM, 100 PSI (ADD HOSE)

HP D-off

110HP300WCUA15IA002 $47,606 3.78 0.89 12.55 382.7823.61AIR COMPRESSOR, 300 CFM, 150 PSI (ADD HOSE)

HP D-off

174VHP400WCUA15IA003 $57,064 4.51 1.07 19.86 533.3333.77AIR COMPRESSOR, 400 CFM, 200 PSI (ADD HOSE)

HP D-off

174HP450WCUA15IA004 $57,064 4.51 1.07 19.86 533.3333.77AIR COMPRESSOR, 450 CFM, 150 PSI (ADD HOSE)

HP D-off

174XP525WCUA15IA005 $57,064 4.51 1.07 19.86 533.3333.77AIR COMPRESSOR, 525 CFM, 125 PSI (ADD HOSE)

HP D-off

300XHP650WCATA15IA006 $126,093 9.98 2.36 34.24 1367.3563.72AIR COMPRESSOR, 650 CFM, 350 PSI (ADD HOSE)

HP D-off

300XHP750WCATA15IA007 $132,188 10.47 2.48 34.24 1367.7264.92AIR COMPRESSOR, 750 CFM, 300 PSI (ADD HOSE)

HP D-off

335VHP825WCUA15IA008 $99,839 7.88 1.87 38.23 965.8163.08AIR COMPRESSOR, 825 CFM, 200 PSI (ADD HOSE)

HP D-off

310XP1000WCATA15IA009 $99,978 7.89 1.88 35.38 1045.8359.88AIR COMPRESSOR, 1,000 CFM, 125 PSI (ADD HOSE)

HP D-off

400XHP1070WCATA15IA010 $178,021 14.13 3.34 45.65 15210.4186.85AIR COMPRESSOR, 1,070 CFM, 350 PSI (ADD HOSE)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-23


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

SULLAIR CORPORATION

76125DPQJDA15SR006 $16,069 1.26 0.30 8.67 240.9313.02AIR COMPRESSOR, 125 CFM, 100 PSI (ADD HOSE)

HP D-off


HP D-off

78185A15SR004 $16,069 1.26 0.30 8.90 240.9313.28AIR COMPRESSOR, 185 CFM, 100 PSI (ADD HOSE)

HP D-off

80260A15SR005 $23,150 1.82 0.43 9.13 261.3414.92AIR COMPRESSOR, 260 CFM, 100 PSI (ADD HOSE)

HP D-off

123375HDPQJDA15SR008 $39,119 3.08 0.73 14.04 422.2723.66AIR COMPRESSOR, 375 CFM, 150 PSI (ADD HOSE)

HP D-off


HP D-off

230600HDTQCAA15SR010 $81,315 6.40 1.53 26.25 1004.7345.86AIR COMPRESSOR, 600 CFM, 150 PSI (ADD HOSE)

HP D-off

300750HHDTQCAA15SR011 $95,683 7.55 1.79 34.24 1035.5757.74AIR COMPRESSOR, 750 CFM, 175 PSI (ADD HOSE)

HP D-off

440900XHA15SR002 $188,800 14.94 3.54 50.21 15711.0194.19AIR COMPRESSOR, 900 CFM, 350 PSI (ADD HOSE)

HP D-off

3001050DTQCAA15SR012 $94,208 7.43 1.77 34.24 1055.4957.46AIR COMPRESSOR, 1,050 CFM, 100 PSI (ADD HOSE)

HP D-off

4501300HDTQCAA15SR013 $164,591 13.06 3.09 51.35 1569.6290.68AIR COMPRESSOR, 1,300 CFM, 150 PSI (ADD HOSE)

HP D-off

4501600HDTQCAA15SR014 $179,150 14.12 3.36 51.35 16210.4293.64AIR COMPRESSOR, 1,600 CFM, 100 PSI (ADD HOSE)

HP D-off

5251900DTQCAA15SR015 $134,237 10.53 2.52 59.91 1647.7994.51AIR COMPRESSOR, 1,900 CFM, 100 PSI (ADD HOSE)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-24


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

NO SPECIFIC MANUFACTURER

3085GA15XX019 $9,415 0.72 0.18 6.14 140.548.95AIR COMPRESSOR, 85 CFM, 100 PSI (ADD HOSE)

HP G

3085DA15XX020 $17,987 1.41 0.34 3.42 241.057.45AIR COMPRESSOR, 85 CFM, 100 PSI (ADD HOSE)

HP D-off


HP G


HP D-off


HP G

50130A15XX024 $20,706 1.63 0.39 5.71 181.2110.58AIR COMPRESSOR, 130 CFM, 100 PSI (ADD HOSE)

HP D-off


HP G


HP D-off


HP G


HP D-off


HP G


HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-25


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

A15 NO SPECIFIC MANUFACTURER (continued)170450A15XX033 $55,956 4.37 1.05 19.40 893.2433.11AIR COMPRESSOR, 450 CFM, 125 PSI (ADD

HOSE) HP D-off


HP D-off


HP D-off


HP D-off


HP D-off

3601200A15XX038 $144,164 11.42 2.70 41.08 1508.4175.02AIR COMPRESSOR, 1,200 CFM, 125 PSI (ADD HOSE)

HP D-off


HP D-off


HP D-off

0.20 SHOP TYPESUBCATEGORY


580/15A15XX041 $2,347 0.17 0.04 0.53 30.131.19AIR COMPRESSOR, 22 CFM, 80 GAL (ADD HOSE)

HP E


HP E


HP E


HP E

EP 1110-1-8, Vol. 130 Nov 09

2-26


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

A15 NO SPECIFIC MANUFACTURER (continued)25120/90A15XX045 $7,927 0.56 0.14 2.66 40.425.34AIR COMPRESSOR, 89 CFM, 120 GAL (ADD

HOSE) HP E


HP E

AIR HOSE, TOOLS & EQUIPMENTA200.10 AIR DRILL HOSESUBCATEGORY


A20XX001 $1,305 0.35 0.03 0.00 10.211.11AIR HOSE, 0.75", 100', HARDROCK A20XX002 $1,511 0.41 0.03 0.00 10.241.28AIR HOSE, 1.00", 100', HARDROCK A20XX003 $1,881 0.51 0.04 0.00 10.301.60AIR HOSE, 1.25", 100', HARDROCK A20XX004 $2,451 0.67 0.05 0.00 10.392.09AIR HOSE, 1.50", 100', HARDROCK A20XX005 $3,473 0.94 0.07 0.00 20.542.95AIR HOSE, 2.00", 100', HARDROCK A20XX006 $4,259 1.16 0.09 0.00 30.673.63AIR HOSE, 2.50", 100', HARDROCK A20XX007 $5,260 1.43 0.11 0.00 40.834.48AIR HOSE, 3.00", 100', HARDROCK A20XX008 $7,030 1.91 0.14 0.00 61.105.98AIR HOSE, 4.00", 100', HARDROCK

0.20 SANDBLAST HOSESUBCATEGORY

CLEMCO INDUSTRIES CORPORATION

A20CM017 $356 0.10 0.01 0.00 10.060.33SANDBLAST HOSE, 0.75"ID, 100' LONG USE AS SAND BLASTING ACCESSORY


EP 1110-1-8, Vol. 130 Nov 09

2-27


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

A20 CLEMCO INDUSTRIES CORPORATION (continued)



0.30 SANDBLASTERS, BREAKERS, & MISC. AIR TOOLSSUBCATEGORY

CHICAGO PNEUMATIC TOOL CO.

20CP-0009AA20CK002 $928 0.14 0.02 0.00 10.090.46ROTARY / CHIP HAMMER, 8 LB, AIR (ADD 30 CFM COMPRESSOR & BIT COSTS)

CFM A

32CP-0014RRA20CK001 $1,538 0.23 0.03 0.00 10.150.76ROTARY / CHIP HAMMER, 15 LB, AIR (ADD 30 CFM COMPRESSOR & BIT COSTS)

CFM A

56CP-0022A20CK003 $1,639 0.25 0.03 0.00 10.160.81ROCK DRILL, 30 LB, AIR (ADD 50 CFM COMPRESSOR & BIT COSTS)

CFM A

130CP-0069A20CK005 $2,019 0.30 0.04 0.00 10.191.00ROCK DRILL, 55 LB, AIR (ADD 140 CFM COMPRESSOR & BIT COSTS)

CFM A

45CP-0111-CHLAA20CK006 $1,111 0.17 0.02 0.00 10.110.55BREAKER-FOUR BOLT, 25 LB (ADD 50 CFM COMPRESSOR & BIT COSTS)

CFM A

63CP-1230-S1.25A20CK008 $1,162 0.17 0.02 0.00 10.110.57BREAKER-FOUR BOLT, 60 LB (ADD 65 CFM COMPRESSOR & BIT COSTS)

CFM A

81CP-1240-S1.25A20CK010 $1,210 0.18 0.02 0.00 10.110.59BREAKER-FOUR BOLT, 90 LB (ADD 90 CFM COMPRESSOR & BIT COSTS)

CFM A

EP 1110-1-8, Vol. 130 Nov 09

2-28


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

CLEMCO INDUSTRIES CORPORATION

100PACKAGE TWOA20CM010 $3,858 0.58 0.07 0.00 40.361.97SANDBLASTER, 2 CF CAP, W/0.50" D X 25'L HOSE (ADD 100 CFM COMPRESSOR & NOZZLE COST)

CFM A

170PACKAGE FOUR

A20CM011 $4,969 0.75 0.09 0.00 50.472.52SANDBLASTER, 4 CF CAP, W/1.00"D X 25'L HOSE (ADD 170 CFM COMPRESSOR & NOZZLE COST)

CFM A

200PACKAGE SIXA20CM012 $5,580 0.84 0.10 0.00 60.522.89SANDBLASTER, 6 CF CAP, W/1.25"D X 25'L HOSE (ADD 200 CFM COMPRESSOR & NOZZLE COST)

CFM A

450A20CM013 $17,014 2.45 0.32 0.00 301.558.53SANDBLASTER, 60 CF CAP, W/1.25"D X 50'L HOSE (ADD 450 CFM COMPRESSOR & NOZZLE COST)

CFM A


CFM A


CFM A

A20CM016 $14,708 2.21 0.27 0.00 691.387.58SANDBLAST ABRASIVE STORAGE HOPPER, 700 CF, 8' DEEP,10' WIDE & 23' HIGH (ADD SAND BLASTER & ACCESSORIES)

WACKER CORPORATION

2EHB11/BL/110A20WC002 $1,095 0.16 0.02 0.18 10.100.96BREAKER/DRILL, 40 LB, ELECTRIC (ADD 2 KW GENERATOR & BIT COSTS)

HP E

4BH 23A20WC004 $3,176 0.48 0.06 0.71 10.302.40BREAKER/DRIVER, 65 LB, W/POWER UNIT (ADD BIT COSTS)

HP G

EP 1110-1-8, Vol. 130 Nov 09

2-29


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)


100STANDARD 25-30 LBS

A20XX021 $1,210 0.18 0.02 0.00 10.110.59PAVEMENT BREAKER, 25-30 LB, HAND HELD (ADD 100 CFM COMPRESSOR & BIT COSTS)

CFM A

100SILENCED 35-45 LBS


CFM A



CFM A



CFM A

10055DRYA20XX025 $2,473 0.37 0.05 0.00 10.241.23ROCK DRILL, DRY, 55 LB, HAND HELD (ADD 100 CFM COMPRESSOR & BIT COSTS)

CFM A

ASPHALT PAVING DISTRIBUTORSA250.00 ASPHALT PAVING DISTRIBUTORSSUBCATEGORY


MAXIMIZER 11A25RS006 $59,398 8.91 1.11 0.00 705.5721.61ASPHALT DISTRIBUTOR, 1,900 GAL, 400 GPM, TRUCK MTD (ADD 32,000 GVW TRUCK)

MAXIMIZER 11A25RS008 $68,106 10.22 1.27 0.00 976.3825.25ASPHALT DISTRIBUTOR, 3,000 GAL, 400 GPM, TRUCK MTD (ADD 42,000 GVW TRUCK)

EP 1110-1-8, Vol. 130 Nov 09

2-30


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT


1100GA25XX001 $50,157 7.52 0.94 0.00 644.7017.91ASPHALT DISTRIBUTOR, 1,100 GAL, 400 GPM, TRUCK MTD (ADD 32,000 GVW TRUCK)



ASPHALT PAVERS & MISCELLANEOUS ROAD EQUIPMENTA300.10 SELF PROPELLEDSUBCATEGORY

BARBER-GREENE COMPANY

98BG230A30BG007 $299,626 30.81 5.56 10.56 31420.9797.54ASPHALT FINISHER, 8' WIDE SCREED, WHEEL, W/15' 6" SCREED EXTENSION, 190 CF HOPPER

HP D-off

112BG225CA30BG004 $337,519 35.86 6.26 12.07 33624.19109.62ASPHALT FINISHER, 8' WIDE SCREED, CRAWLER, W/15' 6" SCREED EXTENSION, 177 CF HOPPER

HP D-off

139BG240CA30BG009 $325,050 33.33 6.03 14.98 37722.70108.20ASPHALT PAVER, 10' WIDE SCREED, WHEEL, W/19' 6" SCREED EXTENSION, 215 CF HOPPER

HP D-off

158BG245CA30BG005 $391,423 41.59 7.26 17.03 37428.06130.32ASPHALT FINISHER, 10' WIDE SCREED, CRAWLER, W/19' 6" SCREED EXTENSION, 215 CF HOPPER

HP D-off

158BG260CA30BG003 $390,776 39.44 7.25 17.03 38226.97129.93ASPHALT FINISHER, 10' WIDE SCREED, WHEEL, W/19' 6" SCREED EXTENSION, 215 CF HOPPER

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-31


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

BLAW KNOX CONSTRUCTION EQUIPMENT CORP.

47PF-150A30BK010 $155,323 15.83 2.88 5.07 15410.8049.64ASPHALT PAVER/FINISHER, 8' WIDE SCREED, WHEEL, 107 CF HOOPER

HP D-off

107PF-161A30BK011 $273,432 28.02 5.07 11.53 21019.0889.79ASPHALT PAVER/FINISHER, 8' WIDE SCREED, WHEEL, 181 CF HOPPER

HP D-off


HP D-off


HP D-off

184PF-5500A30BK017 $350,083 37.20 6.50 19.83 34025.10120.43ASPHALT PAVER/FINISHER, 10' WIDE SCREED, CRAWLER, 218 CF HOPPER

HP D-off

184PF-5510A30BK018 $360,422 38.29 6.69 19.83 32025.84123.32ASPHALT PAVER/FINISHER, 10' WIDE SCREED, CRAWLER, 218 CF HOPPER

HP D-off

105RW 100 AA30BK019 $212,671 22.27 3.95 11.32 24515.0972.29ASPHALT PAVER, SHOULDER PAVING MACHINE, 1'-10' WIDE, BITUMINOUS & AGGREGATE, WHEEL, 72.5 CF HOPPER

HP D-off

173RW 195 DA30BK020 $273,880 28.77 5.08 18.65 33019.4797.85ASPHALT PAVER, SHOULDER PAVING MACHINE, 2'-10' WIDE, BITUMINOUS & AGGREGATE, WHEEL, 73 CF HOPPER

HP D-off

176TITAN 325 EPMA30BK021 $354,690 37.69 6.58 18.97 39925.43120.74ASPHALT PAVER, 32.8' WIDE, CRAWLER W/DUAL TAMPER SCREED, 270 CF HOPPER

HP D-off

145PF-2181A30BK022 $270,008 27.72 5.01 15.63 28318.8793.37ASPHALT PAVER, 8' WIDE SCREED, WHEEL, 2 WHEEL DRIVE, 182 CF HOPPER

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-32


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

A30 BLAW KNOX CONSTRUCTION EQUIPMENT CORP. (continued)

145PF-4410A30BK023 $304,479 32.35 5.65 15.63 26921.83102.90ASPHALT PAVER, 8' WIDE SCREED, CRAWLER, 155 CF HOPPER

HP D-off

CATERPILLAR INC. ( MACHINE DIVISION)

121AP-650BA30CA013 $284,684 30.25 5.28 13.04 40220.4194.44ASPHALT PAVER, 8' WIDE SCREED, CRAWLER, 177 CF HOPPER

HP D-off

107AP-800CA30CA002 $282,244 29.00 5.24 11.53 31919.7492.11ASPHALT PAVER, 8' WIDE+2' EXT. PAVEMASTER SCREED, WHEEL, 195 CF HOPPER

HP D-off

153AP-900BA30CA014 $297,220 30.37 5.51 16.49 37820.70102.12ASPHALT PAVER, 10' WIDE SCREED, WHEEL, 215 CF HOPPER

HP D-off

174AP-1000BA30CA008 $328,394 33.76 6.09 18.75 46822.97113.45ASPHALT PAVER, 10' - 12' WIDE PAVEMASTER SCREED, WHEEL, 215 CF HOPPER

HP D-off

174AP-1050BA30CA015 $476,921 50.67 8.85 18.75 41534.19154.68ASPHALT PAVER, 10' WIDE EXTEND-A-MAT SCREED, CRAWLER, 215 CF HOPPER

HP D-off

173AP-1055BA30CA016 $369,720 39.28 6.86 18.65 41326.50124.58ASPHALT PAVER, 10' WIDE SCREED, CRAWLER, 215 CF HOPPER

HP D-off

173AP-1050BA30CA009 $403,358 42.86 7.48 18.65 41828.91133.99ASPHALT PAVER, 10' - 24' WIDE PAVEMASTER SCREED, CRAWLER, 215 CF HOPPER

HP D-off

CHAMPION ROAD MACHINERY-PRO PAV (WIRTGEN

110780WBA30CH001 $262,756 26.89 4.88 11.86 26518.3387.19ASPHALT PAVER, 8' WIDE SCREED, WHEEL, 190 CF HOPPER

HP D-off


HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-33


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

A30 CHAMPION ROAD MACHINERY-PRO PAV (WIRTGEN (continued)

152880RTBA30CH003 $288,536 30.66 5.35 16.38 28220.6899.29ASPHALT PAVER, 8' WIDE SCREED, CRAWLER-RUBBER TRACK, 190 CF HOPPER

HP D-off


HP D-off


HP D-off

2001110RTB SWIFTRACK

A30CH006 $383,826 40.78 7.12 21.56 40227.51131.82ASPHALT PAVER, 10' WIDE SCREED, CRAWLER-RUBBER TRACK, 225 CF HOPPER

HP D-off

GEHL COMPANY

251448A30GC002 $37,903 3.95 0.70 2.69 672.6813.68ASPHALT PAVER, 8' WIDE SCREED, WHEEL, 80 CF HOPPER

HP D-off

411648A30GC004 $54,515 5.79 1.01 4.42 853.9120.26ASPHALT PAVER, 9' WIDE SCREED, CRAWLER, 120 CF HOPPER

HP D-off

0.20 TOWEDSUBCATEGORY

MIDLAND MACHINERY CO

80SP-8A30MP001 $131,563 10.53 2.47 7.86 1857.7434.96ASPHALT PAVER, SHOULDER PAVING MACHINE, 1'-8' WIDE, BITUMINOUS & AGGREGATE, WHEEL, 80 CF HOPPER

HP D-off

100SP-10A30MP002 $170,923 13.67 3.21 9.83 27510.0544.98ASPHALT PAVER, SHOULDER PAVING MACHINE, 1'-10' WIDE, BITUMINOUS & AGGREGATE, WHEEL, 80 CF HOPPER

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-34


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

0.30 SLURRY SEAL PAVERS (Cold mix)SUBCATEGORY


110MINIMACA30XX001 $143,953 9.45 2.66 10.11 1307.3932.17ASPHALT PAVER, SLURRY SEAL PAVER 8' WIDE, SELF PROPELLED, WHEEL, 80 CF HOPPER

HP D-off

110MACROPAVER 12B

A30XX002 $176,095 11.74 3.26 10.11 1759.1336.25ASPHALT PAVER, SLURRY SEAL PAVER 8' WIDE, TRUCK MTD, 12 CF HOPPER (ADD 40,000 GVW TRUCK)

HP D-off

0.40 MISCELLANEOUS ROAD EQUIPMENTSUBCATEGORY

BLAW KNOX CONSTRUCTION EQUIPMENT CORP.

184MC-330A30BK024 $344,545 26.94 6.46 18.08 43019.9389.10ASPHALT PAVER, MOBILE CONVEYOR, 60" WIDE BELT, WHEEL (ADD ASPHALT PAVER UNIT)

HP D-off


107BG-650A30CA007 $119,856 9.30 2.25 10.51 1716.9035.82ASPHALT PAVER, ASPHALT WINDROW ELEVATOR, WHEEL (ADD ASPHALT PAVER UNIT)

HP D-off

LEE-BOY

1103000A30LD001 $140,079 10.70 2.63 10.81 1987.9840.42ASPHALT PAVER, ASPHALT FORCE FEED LOADER, 30" WIDE BELT, WINDROW OR LOOSE, WHEEL (ADD ASPHALT PAVER UNIT)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-35


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

ROADTEC ( ASTEC INDUSTRIES COMPANY)

275SB-1500A30RT001 $496,161 39.66 9.31 27.02 60029.14128.86ASPHALT PAVER, ASPHALT MATERIAL TRANSFER VEHICLE, 15 TON HOPPER, 600 TPH, 65" WIDE CONVEYOR, WHEEL

HP D-off

275SB-2500BA30RT002 $520,782 41.59 9.77 27.02 79030.57133.77ASPHALT PAVER, ASPHALT MATERIAL TRANSFER VEHICLE, 25 TON HOPPER, 1000 TPH, 69" WIDE CONVEYOR, WHEEL

HP D-off

ASPHALT PAVING KETTLESA350.00 ASPHALT PAVING KETTLESSUBCATEGORY

AEROIL PRODUCTS COMPANY, INC.

5KEB-80KEA35AE001 $10,070 1.27 0.20 0.89 90.846.13ASPHALT/PAVEMENT KETTLE, 80 GAL, TRAILER W/PUMP & HOSE

HP G


HP G


HP G


HP G


HP G

EP 1110-1-8, Vol. 130 Nov 09

2-36


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

ASPHALT & CONCRETE MILLERS / PROFILERS / PLANERS / ROTARY GRINDERSA400.00 ASPHALT & CONCRETE MILLERS / PROFILERS / PLANERS / ROTARY GRINDERSSUBCATEGORY


500PM-465A40CA008 $476,368 63.52 9.44 71.33 50541.20252.23ASPHALT COLD PLANER, 75" W X 10" D, CRAWLER (ADD CUTTING TEETH COSTS)

HP D-off

625PM-565BA40CA009 $670,244 89.37 13.28 89.16 73557.97342.19ASPHALT COLD PLANER, 83" W X 12" D, CRAWLER (ADD CUTTING TEETH COSTS)

HP D-off

TEREX - CMI (TEREX ROADBUILDING)

950PR-950A40CW001 $790,432 105.39 15.66 135.52 1,20568.36437.96ASPHALT PROFILER, MAX 12.5' W X 15" D, CRAWLER (ADD CUTTING TEETH COSTS)

HP D-off

ROADTEC ( ASTEC INDUSTRIES COMPANY)

230RX-20BA40RT001 $324,816 41.83 6.44 32.81 32427.36152.85ASPHALT COLD PLANER, 40" W X 10" D, WHEEL (ADD CUTTING TEETH COSTS)

HP D-off

250RX-25A40RT002 $424,475 56.60 8.41 35.66 42036.71193.13ASPHALT COLD PLANER, 52" W X 8" D, CRAWLER (ADD CUTTING TEETH COSTS)

HP D-off

460RX-45BA40RT003 $522,387 69.65 10.35 65.62 61745.18262.31ASPHALT COLD PLANER, 78" W X 12" D, CRAWLER (ADD CUTTING TEETH COSTS)

HP D-off


HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-37


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

A40 ROADTEC ( ASTEC INDUSTRIES COMPANY) (continued)


HP D-off

ASPHALT RECYCLERS & SEALERSA450.00 ASPHALT RECYCLERS & SEALERSSUBCATEGORY


HEPR-52VA45AE001 $8,973 1.38 0.18 0.00 110.8710.66ASPHALT RESURFACER-PATCHER, 4' WIDE, 17.3 SF, 600,000 BTU INFRA-RED HEATER, TRAILER MTD

HEPR-96VA45AE002 $17,473 2.74 0.36 0.00 161.7321.24ASPHALT RESURFACER-PATCHER, 8' WIDE, 32.0 SF, 1,200,000 BTU INFRA-RED HEATER, TRAILER MTD

HEPR-120VA45AE003 $20,575 3.24 0.42 0.00 172.0425.10ASPHALT RESURFACER-PATCHER, 10' WIDE, 40.0 SF, 1,420,000 BTU INFRA-RED HEATER, TRAILER MTD


80RA-2000A45RS001 $46,867 7.41 0.95 7.86 604.6628.21ASPHALT SPRAY PATCHER, 300 GAL, ARTICULATED BOOM - 17' R, TRAILER MTD

HP D-off

210RA-300A45RS002 $150,368 24.06 3.06 24.15 17915.0988.54ASPHALT SPRAY PATCHER, 400 GAL, TELESCOPIC BOOM - 22' EXT, TRUCK MTD

HP D-on

EP 1110-1-8, Vol. 130 Nov 09

2-38


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

SEALMASTER, INC.

30SP300 DUALA45SE003 $36,890 5.82 0.75 2.95 433.6620.18ASPHALT SEALCOATER, 320 GAL, 75 GPM, 108" WIDE DUAL SPRAY, SQUEEGEE, SELF PROPELLED

HP D-off

13TR-1000A45SE004 $23,568 3.60 0.48 2.31 522.2812.47ASPHALT SEALCOATER, 1000 GAL, 50 GPM, 88'' WIDE SPRAY BAR, TRAILER MTD

HP G

BATCH PLANTS, ASPHALT & CONCRETEB100.20 CONCRETESUBCATEGORY

CEMEN TECH

18MCD2-50HTB10CC007 $46,487 4.54 0.89 3.20 803.1619.35BATCH PLANT, CONCRETE DISPENSER, 15 CY/HR MAX, W/TWO AGGREGATE BINS, 2 CY/ 1 CY CEMENT BIN/ 7' LONG SLOPING 8" DIA SCREW WET MIXER/DELIVERER/ 250 GAL WATER TANK/ & METERING PUMP, 2 CY LOAD, TRAILER MTD

HP G

163MCD5-100HB10CC008 $127,007 12.37 2.43 28.95 1328.6271.68BATCH PLANT, CONCRETE DISPENSER, 30 CY/HR MAX, W/TWO AGGREGATE BINS, 5.5 CY/ 1.9 CY CEMENT BIN/ 9' LONG SLOPING 9" DIA SCREW WET MIXER/DELIVERER/ 250 GAL WATER TANK/ & METERING PUMP, 5 CY LOAD, TRUCK MTD

HP G

EP 1110-1-8, Vol. 130 Nov 09

2-39


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

B10 CEMEN TECH (continued)200MCD8-100HB10CC009 $143,061 13.76 2.74 35.52 1949.6283.96BATCH PLANT, CONCRETE DISPENSER,

30 CY/HR MAX, W/TWO AGGREGATE BINS, 9.3 CY/ 3.1 CY CEMENT BIN/ 9' LONG SLOPING 12" DIA SCREW WET MIXER/DELIVERER/ 250 GAL WATER TANK/ & METERING PUMP, 8 CY LOAD, TRUCK MTD

HP G

200MCD8-150HB10CC010 $154,180 14.87 2.95 35.52 20410.3987.26BATCH PLANT, CONCRETE DISPENSER, 60 CY/HR MAX, W/TWO AGGREGATE BINS, 9.6 CY/ 3.1 CY CEMENT BIN/ 9' LONG SLOPING 12" DIA SCREW WET MIXER/DELIVERER/ 250 GAL WATER TANK/ & METERING PUMP, 8 CY LOAD, TRUCK MTD

HP G

18210 BBLB10CC012 $21,198 2.12 0.41 3.20 351.4710.26BATCH PLANT, SILO, CEMENT, 830 CF, 210 BARREL (BATCH PLANT ATTACHMENT)

HP G

20HS-240B10CC011 $21,547 2.15 0.41 1.85 451.499.74BATCH PLANT, SILO, CEMENT, 38 TON HORIZONTAL 240 BARREL (BATCH PLANT ATTACHMENT)

HP E

18300 BBLB10CC013 $25,619 2.56 0.49 3.20 481.7711.51BATCH PLANT, SILO, CEMENT, 1,200 CF, 300 BARRL (BATCH PLANT ATTACHMENT)

HP G

5B10CC014 $6,638 0.66 0.13 0.46 100.463.03BATCH PLANT, CEMENT LOADING AUGER, 6" DIA, 19' LONG (BATCH PLANT ATTACHMENT)

HP E

CON-E-CO

200MTM 12B10CL025 $273,030 27.13 5.23 18.46 13018.80103.05BATCH PLANT, CONCRETE MIXER, 12 CY, TILT DRUM, 11.67' DIA, REMOVABLE AXLES, TRAILER MTD (ADD DRY BATCH PLANT)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-40


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

B10 CON-E-CO (continued)35VERSA-PLANT

10B10CL021 $84,532 8.15 1.62 3.23 1905.7027.94BATCH PLANT, CONCRETE AGGREGATE

DRY, 40CY/HR, 10 CY AGGREGATE BATCHER, W/30" X 40' LOADING CONVEYOR, SCALES & WATER METER INCLUDED, TRAILER MTD (ADD 5 KW GENERATOR, WATER TANK & WET BATCHER)

HP E

30PLP MODEL 12B10CL015 $157,915 15.27 3.03 2.77 38010.6749.70BATCH PLANT, CONCRETE AGGREGATE DRY, 200 CY/HR, W/TWO AGGREGATE BINS, 81 TON, 60 CY/ 36"X20' CONVEYOR/ 3 BIN 12 CY AGGREGATE BATCHER/ 30"X33.5' LOADING CONVEYOR/ & 475 BARREL, 88 TON CEMENT SILO, TRAILER MTD (ADD 110 KW GENERATOR)

HP E

120LO-PRO 10B10CL005 $295,832 29.02 5.67 11.08 41020.1899.73BATCH PLANT, CONCRETE AGGREGATE DRY, 275 CY/HR, W/TWO AGGREGATE BINS, 65 TON, 50 CY/ 36"X20' CONVEYOR/ 10 CY AGGREGATE BATCHER/ 36"X36' LOADING CONVEYOR/ & 215 BARREL, 35 TON CEMENT SILO, TRAILER MTD (ADD 140 KW GENERATOR)

HP E

120LO-PRO 12B10CL006 $300,747 29.51 5.76 11.08 42620.52101.07BATCH PLANT, CONCRETE AGGREGATE DRY, 275 CY/HR, W/TWO AGGREGATE BINS, 65 TON, 50 CY/ 36"X20' CONVEYOR/ 12 CY AGGREGATE BATCHER/ 36"X36' LOADING CONVEYOR/ & 215 BARREL, 35 TON CEMENT SILO, TRAILER MTD (ADD 140 KW GENERATOR)

HP E

B10CL027 $21,193 2.12 0.41 0.00 1441.475.81BATCH PLANT, CEMENT SILO, 1,910 CF, 475 BARREL (BATCH PLANT ATTACHMENT)

EP 1110-1-8, Vol. 130 Nov 09

2-41


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

B10 CON-E-CO (continued)5B10CL042 $3,183 0.32 0.06 0.46 50.221.58BATCH PLANT, SCREW CONVEYOR, 6"

DIA, 10' LONG (CEMENT SILO ATTACHMENT)

HP E

10B10CL045 $4,088 0.41 0.08 0.92 110.292.53BATCH PLANT, SCREW CONVEYOR, 6" DIA, 20' LONG (CEMENT SILO ATTACHMENT)

HP E


HP E


HP E


HP E


HP E

EXCEL MACHINERY LTD.

25EXCEL PORT-A-PUG

B10EM001 $425,949 41.67 8.16 4.44 59029.00123.77BATCH PLANT, CONCRETE CONTINUOUS PUGG MILL MIXER, 400 CY/HR MAX, W/12 CY AGGREGATE STORAGE BIN/ 48"X18' METERING CONVEYOR/ CEMENT SILO, 44 TON, 34.8 CY/ 30" X 37' CONVEYOR, TRAILER MTD (ADD 200 KW GENERATOR)

HP G

10B10EM002 $29,604 2.69 0.57 0.92 451.9210.33BATCH PLANT, CEMENT SILO, 45 TON HORIZONTAL 350 BARREL (BATCH PLANT ATTACHMENT)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-42


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

B10 EXCEL MACHINERY LTD. (continued)B10EM003 $27,628 2.76 0.53 0.00 2221.917.57BATCH PLANT, CEMENT SILO, 2,200 CF

(BARREL CAP 550 MAX / 450 MIN) W/DRIVE-THRU TYPE UNDERSTRUCTURE (BATCH PLANT ATTACHMENT)

JOHNSON-ROSS (TEREX ROADBUILDING)

15BANDIT 5B10RC007 $148,350 14.48 2.84 1.38 3,00010.0845.05BATCH PLANT, CONCRETE AGGREGATE DRY, 100 CY/HR, W/TWO AGGREGATE BINS, 65 TON, 48 CY/ 36" X 20' CONVEYOR/ 2 BIN 5 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 257 BARREL, 48 TON CEMENT SILO, TRAILER MTD (ADD 100 KW GENERATOR)

HP E

50RUSTLER IIIB10RC032 $207,034 20.11 3.97 4.62 53614.0367.93BATCH PLANT, CONCRETE AGGREGATE DRY, 160 CY/HR, W/TWO AGGREGATE BINS, 28 TON, 21 CY/ 2 BIN 12 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 400 BARREL, 75 TON CEMENT SILO, TRAILER MTD (ADD 130 KW GENERATOR)

HP E

46RUSTLER IIB10RC006 $191,499 18.56 3.67 4.20 48912.9563.02BATCH PLANT, CONCRETE AGGREGATE DRY, 160 CY/HR, W/3 AGGREGATE BINS, 71 TON, 52 CY/ 36" X 20' CONVEYOR/ 3 BIN 12 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ 375 BARREL, 70 TON CEMENT SILO, TRAILER MTD (ADD 130KW GENERATOR)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-43


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

B10 JOHNSON-ROSS (TEREX ROADBUILDING) (continued)

30BANDIT 12 BTRB10RC008 $160,580 15.70 3.08 2.77 25010.9350.53BATCH PLANT, CONCRETE AGGREGATE DRY, 200 CY/HR, W/THREE AGGREGATE BINS, 65 TON, 48 CY/ 36" X 20' CONVEYOR/ 3 BIN 12 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 720 BARREL, 134 TON CEMENT SILO, TRAILER MTD (ADD 100 KW GENERATOR)

HP E

40B10RC027 $145,474 14.55 2.79 3.69 3410.0747.55BATCH PLANT, CONCRETE MIXER, 4.5 CY, TILT DRUM, SKID MTD (ADD DRY BATCH PLANT)

HP E


HP E


HP E


HP E


HP E

75MOBILE MIXERB10RC016 $235,306 22.94 4.51 6.92 42015.9880.21BATCH PLANT, CONCRETE MIXER, 4.5CY, TILT DRUM TYPE, REVOLVING LIFT STAND, TRAILER MTD (ADD DRY BATCH PLANT & POWER)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-44


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

STEPHENS MANUFACTURING CO., INC.

25DC-12B10SN031 $75,398 6.89 1.44 2.31 3404.8925.09BATCH PLANT, CONCRETE AGGREGATE DRY, 100 CY/HR, W/2 BIN 12 CY BATCHER/ 24" X 41' LOADING CONVEYOR/ & 311 BARREL, 58 TON CEMENT SILO, TRAILER MTD (ADD 100 KW GENERATOR)

HP E

30DC COLTB10SN033 $140,852 13.44 2.70 2.77 3409.4243.91BATCH PLANT, CONCRETE AGGREGATE DRY, 100 CY/HR, W/2 BIN 12 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 311 BARREL, 58 TON CEMENT SILO, TRAILER MTD (ADD 100 KW GENERATOR)

HP E

30MUSTANG 5B10SN032 $114,995 10.84 2.20 2.77 4207.6237.05BATCH PLANT, CONCRETE AGGREGATE DRY, 160 CY/HR, W/3 AGGREGATE STORAGE BINS, 29.6 TON, 40 CY/ 3 BIN 5 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 251 BARREL, 47 TON CEMENT SILO, TRAILER MTD (ADD 115 KW GENERATOR)

HP E

20STALLIONB10SN034 $152,811 14.62 2.93 1.85 36010.2445.76BATCH PLANT, CONCRETE AGGREGATE DRY, 160 CY/HR, W/3 AGGREGATE BIN STORAGE, 70 TON, 48 CY/ 2 BIN 10 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 374 BARREL, 70 TON CEMENT SILO, TRAILER MTD (ADD 100 KW GENERATOR)

HP E

45MUSTANG 10B10SN036 $150,118 14.35 2.88 4.15 50010.0648.80BATCH PLANT, CONCRETE AGGREGATE DRY, 160 CY/HR, W/3 AGGREGATE BIN STORAGE, 75 TON, 55 CY/ 2 BIN 10 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 351 BARREL, 65 TON CEMENT SILO, TRAILER MTD (ADD 115 KW GENERATOR)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-45


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

B10 STEPHENS MANUFACTURING CO., INC. (continued)

30THOROUGH-BRED

B10SN035 $160,374 15.38 3.07 2.77 30010.7649.39BATCH PLANT, CONCRETE AGGREGATE DRY, 180 CY/HR, W/4 AGGREGATE BIN STORAGE, 65 TON, 48 CY/ 2 BIN 12 CY BATCHER/ 30" X 33.5' LOADING CONVEYOR/ & 374 BARREL, 70 TON CEMENT SILO, TRAILER MTD (ADD 100 KW GENERATOR)

HP E

0.30 PUGMILLSUBCATEGORY

KOLBERG - PIONEER, INC

9552 PORTABLE PUGMILL

B10KB001 $169,990 13.34 3.19 8.77 1909.8651.27BATCH PLANT, PUGMILL, CONTINUOUS MIXER, 48" DIA TWIN SHAFT X 6' LONG, W/9 CY FEEDER HOPPER/ 36" X 11.5' BELT FEEDER/ 30" X 27' CONVEYOR/ WATER OR ASPHALT PUMP & METER (ADD 95 KW GENERATOR & ANY MATERIAL FEEDS)

HP E

22052S PORTABLE PUGMILL

B10KB002 $302,540 23.91 5.67 20.31 23017.6398.47BATCH PLANT, PUGMILL, CONTINUOUS MIXER, 48" DIA TWIN SHAFT X 8' LONG, W/13 CY FEEDER HOPPER/ TWO - 36" X 11.5' BELT FEEDERS/ 2ND 11 CY FEEDER HOPPER/ 30" X 27' CONVEYOR/ WATER OR ASPHALT PUMP & METER (ADD 220 KW GENERATOR & ANY MATERIAL FEEDS)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-46


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

BROOMS, STREET SWEEPERS & FLUSHERSB150.00 BROOMS, STREET SWEEPERS & FLUSHERSSUBCATEGORY

BROCE MANUFACTURING COMPANY

80RJ-350B15BM001 $44,367 4.99 0.80 7.86 453.3020.17BROOM, 8' BROOM PATH, PAVEMENT, SELF PROPELLED

HP D-off

ELGIN SWEEPER COMPANY

100PELICAN PB15EC002 $122,644 13.63 2.21 9.83 1289.0342.32STREET SWEEPER, 10' BROOM PATH, 3.5 CY HOPPER, 180 GAL WATER TANK, SELF PROPELLED

HP D-off

49EAGLE FB15EC001 $185,332 20.56 3.33 8.60 15013.6156.93170 HP D-onSTREET SWEEPER, 10' BROOM PATH, 4.5 CY HOPPER, 280 GAL WATER TANK, DUAL ENGINE, SELF PROPELLED

HP D-off

230BROOM BEAR FL42H

B15EC003 $174,054 19.54 3.13 22.60 21312.9069.83STREET SWEEPER, 12' BROOM PATH, 4.5 CY HOPPER, 350 GAL WATER TANK, SELF PROPELLED

HP D-off

M-B COMPANIES, INC.

MT-ARB15MB001 $7,866 0.88 0.14 0.00 100.582.09STREET SWEEPER, 7' BROOM PATH, W/SPRINKLER AND 152 GAL WATER TANK, PTO DRIVE (ADD 45-100 HP TRACTOR)

HTB15MB002 $9,503 1.07 0.17 0.00 120.712.55STREET SWEEPER, 7' BROOM PATH, W/SPRINKLER AND 152 GAL WATER TANK, PTO DRIVE (ADD 45-100 HP TRACTOR)

EP 1110-1-8, Vol. 130 Nov 09

2-47


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

B15 M-B COMPANIES, INC. (continued)53TB15MB003 $13,826 1.50 0.25 0.00 181.003.73STREET SWEEPER, 7' BROOM PATH,

W/SPRINKLER AND 152 GAL WATER TANK, TOWED, HYDRAULIC (ADD TOWING UNIT)

1853MHB15MB004 $15,942 1.74 0.29 3.20 171.167.59STREET SWEEPER, 7' BROOM PATH, W/SPRINKLER AND 152 GAL WATER TANK, TOWED (ADD TOWING UNIT)

HP G


80CHALLENGER IIB15RS005 $50,964 5.65 0.92 7.86 753.7521.89STREET SWEEPER, 7' BROOM PATH, W/SPRINKLER AND 125 GAL WATER TANK, SELF PROPELLED

HP D-off

80RB-48B15RS001 $39,183 4.35 0.70 7.86 522.8818.87STREET SWEEPER, 8' BROOM PATH, W/SPRINKLER AND 150 GAL WATER TANK, SELF PROPELLED

HP D-off

TERRAMITE CONSTRUCTION EQUIPMENT

37TSS46B15TB001 $22,350 2.46 0.40 3.64 341.639.82STREET SWEEPER, 6' BROOM PATH, W/SPRINKLER AND 2 - 50 GAL WATER TANKS, SELF PROPELLED

HP D-off

37TSS48B15TB002 $22,491 2.48 0.40 3.64 341.649.86STREET SWEEPER, 8' BROOM PATH, W/SPRINKLER AND 2 - 50 GAL WATER TANKS, SELF PROPELLED

HP D-off

WALDON, INC.

80SWEEPMASTER 250

B15WD001 $35,134 3.90 0.63 7.86 482.5817.85BROOM, 7.5' BROOM PATH, PAVEMENT, SELF PROPELLED

HP D-off

80SWEEPMASTER 250

B15WD002 $36,416 4.04 0.65 7.86 482.6718.17BROOM, 90" BROOM PATH, PAVEMENT, W/SPRINKLER AND 180 GAL WATER TANK, SELF PROPELLED

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-48


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

BRUSH CHIPPERSB200.00 BRUSH CHIPPERSSUBCATEGORY

BANDIT INDUSTRIES, INC.

2565B20BN001 $11,063 1.22 0.20 4.44 200.818.08BRUSH CHIPPER, 6" CAPACITY, DISC TYPE, TRAILER MTD

HP G

7190W-XPB20BN002 $17,609 1.95 0.32 12.61 321.3019.28BRUSH CHIPPER, 9" CAPACITY, DISC TYPE, TRAILER MTD

HP G

140200XPB20BN003 $22,317 2.47 0.40 24.86 581.6434.64BRUSH CHIPPER, 12" CAPACITY, DISC TYPE, TRAILER MTD

HP G

701290B20BN005 $19,207 2.12 0.35 12.43 441.4119.49BRUSH CHIPPER, 12" CAPACITY, DRUM TYPE, TRAILER MTD

HP G


HP G


HP D-off

MORBARK, INC.

862070XLB20MQ001 $21,708 2.43 0.39 8.45 401.6115.41BRUSH CHIPPER, 10" CAPACITY, DRUM TYPE, TRAILER MTD

HP D-off

14013B20MQ003 $30,256 3.36 0.54 13.76 682.2223.73BRUSH CHIPPER, 13" CAPACITY, DRUM TYPE, TRAILER MTD

HP D-off

2502400XLB20MQ004 $35,419 3.85 0.64 24.57 942.5737.37BRUSH CHIPPER, 18" CAPACITY, DRUM TYPE, TRAILER MTD

HP D-off

65022 RXLB20MQ005 $379,595 42.36 6.83 63.88 70028.01176.08BRUSH CHIPPER, LOG CHIPPER, 22" CAPACITY, DISC TYPE, TRAILER MTD

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-49


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

BUCKETS, CLAMSHELLB250.00 BUCKETS, CLAMSHELLSUBCATEGORY

HAWCO MANUFACTURING COMPANY, LLC

HD-050B25HB001 $18,682 2.10 0.34 0.00 301.394.37BUCKET, CLAMSHELL, 0.5 CY, HEAVY DUTY/DIGGING












EP 1110-1-8, Vol. 130 Nov 09

2-50


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT


1/4SSNB25XX001 $8,443 0.95 0.15 0.00 140.631.97BUCKET, CLAMSHELL, 0.2 CY, SQUARE NOSE, STANDARD



1SSNB25XX004 $16,912 1.90 0.30 0.00 431.253.95BUCKET, CLAMSHELL, 1.0 CY, SQUARE NOSE, STANDARD

1-1/4SSNB25XX005 $19,701 2.22 0.35 0.00 491.464.61BUCKET, CLAMSHELL, 1.2 CY, SQUARE NOSE, STANDARD










EP 1110-1-8, Vol. 130 Nov 09

2-51


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

B25 NO SPECIFIC MANUFACTURER (continued)5-1/2SSNB25XX015 $62,886 7.07 1.13 0.00 1584.6714.70BUCKET, CLAMSHELL, 5.5 CY, SQUARE

NOSE, STANDARD 6SSNB25XX016 $63,418 7.13 1.14 0.00 1664.7114.83BUCKET, CLAMSHELL, 6.0 CY, SQUARE

NOSE, STANDARD 6-1/2SSNB25XX017 $68,478 7.70 1.23 0.00 1775.0816.01BUCKET, CLAMSHELL, 6.5 CY, SQUARE

NOSE, STANDARD 7SSNB25XX018 $64,998 7.31 1.17 0.00 1854.8315.20BUCKET, CLAMSHELL, 7.0 CY, SQUARE

NOSE, STANDARD 7-1/2SSNB25XX019 $72,715 8.18 1.31 0.00 1925.4017.01BUCKET, CLAMSHELL, 7.5 CY, SQUARE

NOSE, STANDARD

BUCKETS, CONCRETEB300.10 GENERAL PURPOSE, MANUAL TRIPSUBCATEGORY

GAR-BRO MANUFACTURING COMPANY

413-GB30GB018 $3,187 0.38 0.06 0.00 40.250.77BUCKET, CONCRETE, GENERAL PURPOSE, 0.5 CY






EP 1110-1-8, Vol. 130 Nov 09

2-52


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

0.20 LAYDOWNSUBCATEGORY


425-AB30GB006 $20,622 2.45 0.36 0.00 261.595.09BUCKET, CONCRETE, LAYDOWN, 1.0 CY, HEAVY DUTY AIR GATE





0.30 LOWBOYSUBCATEGORY

CAMLEVER

LB-375B30CR001 $4,770 0.57 0.08 0.00 20.371.21BUCKET, CONCRETE, LOWBOY, 0.38 CY, AIR GATE





LXB-150B30CR009 $7,069 0.84 0.12 0.00 60.541.80BUCKET, CONCRETE, LOWBOY, 1.5 CY, AIR GATE

EP 1110-1-8, Vol. 130 Nov 09

2-53


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

B30 CAMLEVER (continued)LB-200B30CR006 $7,900 0.94 0.14 0.00 80.612.01BUCKET, CONCRETE, LOWBOY, 2.0 CY,

AIR GATE LXB-200B30CR010 $8,247 0.98 0.14 0.00 60.632.09BUCKET, CONCRETE, LOWBOY, 2.0 CY,



AIR GATE

0.40 LOW SLUMPSUBCATEGORY


440-AB30GB011 $16,318 1.94 0.28 0.00 201.254.15BUCKET, CONCRETE, LOW SLUMP, 1.0 CY, AIR GATE







EP 1110-1-8, Vol. 130 Nov 09

2-54


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

BUCKETS, DRAGLINEB350.10 LIGHT WEIGHTSUBCATEGORY

HENDRIX MANUFACTURING COMPANY, INC.

LSB35HE001 $7,692 0.87 0.14 0.00 150.581.81BUCKET, DRAGLINE, 0.75 CY, LIGHT WEIGHT/PERFORATED












EP 1110-1-8, Vol. 130 Nov 09

2-55


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

B35 HENDRIX MANUFACTURING COMPANY, INC. (continued)






SAUERMAN (NATIONAL OILWELL VARCO)

SC-1050-KB35SA001 $19,268 2.17 0.35 0.00 151.444.51BUCKET, DRAGLINE, 1.0 CY, CRESCENT







EP 1110-1-8, Vol. 130 Nov 09

2-56


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

B35 SAUERMAN (NATIONAL OILWELL VARCO) (continued)

SC-1140-KB35SA009 $98,578 11.09 1.77 0.00 1067.3223.05BUCKET, DRAGLINE, 10.0 CY,CRESCENT

SC-1150-KB35SA010 $120,338 13.54 2.16 0.00 1328.9328.14BUCKET, DRAGLINE, 12.0 CY,CRESCENT


6-1/2LB35XX001 $30,571 3.44 0.55 0.00 942.277.15BUCKET, DRAGLINE, 6.5 CY, LIGHT WEIGHT




11LB35XX005 $48,672 5.48 0.88 0.00 1483.6211.39BUCKET, DRAGLINE, 11.0 CY, LIGHT WEIGHT

13LB35XX006 $59,873 6.74 1.08 0.00 1784.4514.01BUCKET, DRAGLINE, 13.0 CY, LIGHT WEIGHT

0.20 MEDIUM WEIGHTSUBCATEGORY


TSB35HE018 $8,314 0.83 0.15 0.00 170.571.74BUCKET, DRAGLINE, 0.75 CY, MEDIUM WEIGHT



EP 1110-1-8, Vol. 130 Nov 09

2-57


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)















EP 1110-1-8, Vol. 130 Nov 09

2-58


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT




6-1/2MB35XX007 $34,549 3.45 0.61 0.00 1012.347.23BUCKET, DRAGLINE, 6.5 CY, MEDIUM WEIGHT




11MB35XX011 $55,962 5.60 0.99 0.00 1693.7911.73BUCKET, DRAGLINE, 11.0 CY, MEDIUM WEIGHT

13MB35XX012 $70,917 7.09 1.26 0.00 2114.8114.87BUCKET, DRAGLINE, 13.0 CY, MEDIUM WEIGHT

0.30 HEAVY WEIGHTSUBCATEGORY


MH-SB35HE035 $31,050 2.79 0.54 0.00 691.945.90BUCKET, DRAGLINE, 2.75 CY, HEAVY WEIGHT




EP 1110-1-8, Vol. 130 Nov 09

2-59


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)












3/4HB35XX013 $8,706 0.78 0.15 0.00 200.541.65BUCKET, DRAGLINE, 0.75 CY, HEAVY WEIGHT

1HB35XX014 $9,780 0.88 0.17 0.00 230.611.86BUCKET, DRAGLINE, 1.0 CY, HEAVY WEIGHT

1-1/2HB35XX015 $14,544 1.31 0.25 0.00 350.912.76BUCKET, DRAGLINE, 1.5 CY, HEAVY WEIGHT

EP 1110-1-8, Vol. 130 Nov 09

2-60


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

B35 NO SPECIFIC MANUFACTURER (continued)2HB35XX016 $16,605 1.49 0.29 0.00 421.043.15BUCKET, DRAGLINE, 2.0 CY, HEAVY

WEIGHT 2-1/2HB35XX017 $18,141 1.63 0.32 0.00 481.143.45BUCKET, DRAGLINE, 2.5 CY, HEAVY






WEIGHT 11HB35XX023 $68,795 6.19 1.21 0.00 1984.3113.09BUCKET, DRAGLINE, 11.0 CY, HEAVY

WEIGHT

CHAIN SAWSC050.00 CHAIN SAWSSUBCATEGORY

OLYMPYK CHAIN SAWS

2941C05OL001 $339 0.15 0.01 0.56 10.091.33CHAIN SAW, 16"-18" BAR HP G




EP 1110-1-8, Vol. 130 Nov 09

2-61


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

COMPACTORS, WALK-BEHIND OR REMOTE CONTROLLERC100.10 COMPACTORS, RAMMERS / TAMPERS & VIBRATORY PLATESSUBCATEGORY

COMPACTION AMERICA (BOMAG)

3BT 60/4C10BO001 $4,554 1.08 0.09 0.73 20.633.67COMPACTOR, RAMMER, TAMPER, 11" X 13.2" SHOE, 2,630 LBS IMPACT

HP G

4BP 10/36-2C10BO003 $2,486 0.59 0.05 0.98 20.352.65COMPACTOR, VIBROPLATE, 14.2" X 22" PLATE, 2,250 LBS IMPACT

HP G

6BP 18/45-2C10BO004 $2,762 0.66 0.05 1.46 20.383.36COMPACTOR, VIBROPLATE, 17.7" X 22" PLATE, 4,050 LBS IMPACT

HP G

4BPR 30/38D-3C10BO007 $11,273 2.68 0.22 0.55 51.567.68COMPACTOR, VIBROPLATE, 22.8" X 31.1" PLATE, REVERSIBLE, 7,200 LBS IMPACT

HP D-off

9BPR 55/65DC10BO008 $15,348 3.65 0.30 1.23 102.1311.00COMPACTOR, VIBROPLATE, 25.6" X 35.4" PLATE, REVERSIBLE, 11,250 LBS IMPACT

HP D-off

WACKER CORPORATION

4DS 70C10WC003 $3,763 0.89 0.07 0.55 20.522.96COMPACTOR, RAMMER, 13" X 13" SHOE, 3,550 LBS IMPACT

HP D-off

6BPU 2540 AC10WC006 $4,606 1.09 0.09 1.34 30.644.38COMPACTOR, VIBROPLATE, 19.5" X 25.5" PLATE, REVERSIBLE, 5,600 LBS IMPACT

HP G

9BPU 3545AC10WC007 $7,046 1.67 0.14 2.19 70.986.86COMPACTOR, VIBROPLATE, 23.5" X 35.5" PLATE, REVERSIBLE, 7,550 LBS IMPACT

HP G

9DPU 4045HC10WC008 $12,711 3.02 0.25 1.23 71.769.35COMPACTOR, VIBROPLATE, 24" X 35.5" PLATE, REVERSIBLE, 9,000 LBS IMPACT

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-62


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

C10 WACKER CORPORATION (continued)14DPU 7060C10WC015 $25,420 6.04 0.50 1.91 153.5218.08COMPACTOR, VIBROPLATE, 25.5" X 42"

PLATE, REVERSIBLE, 15,600 LBS IMPACT

HP D-off

0.20 ROLLERS, VIBRATORYSUBCATEGORY


4BW 55EC10BO009 $6,433 1.37 0.13 0.98 30.824.97COMPACTOR, ROLLER, VIBRATORY, 22"W X 15.7"DIA, SINGLE SMOOTH DRUM, WALK BEHIND, 2,273 LBS IMPACT

HP G

5BW65S-2C10BO015 $14,799 3.14 0.31 0.68 131.889.69COMPACTOR, ROLLER, VIBRATORY, 25.6"W X 15.7"DIA, DOUBLE SMOOTH DRUMS, WALK BEHIND, 2,655 LBS IMPACT

HP D-off

8BW 65HC10BO011 $17,225 3.66 0.36 1.09 162.1911.61COMPACTOR, ROLLER, VIBRATORY, 25.6"W X 15.7"DIA, DOUBLE SMOOTH DRUMS, WALK BEHIND, 1,980 LBS IMPACT

HP D-off

9BW75S-2C10BO016 $21,607 4.59 0.45 1.23 202.7514.41COMPACTOR, ROLLER, VIBRATORY, 29.5"W X 18.9"DIA, DOUBLE SMOOTH DRUMS, WALK BEHIND, 4,455 LBS IMPACT

HP D-off

19BMP851C10BO013 $45,498 9.67 0.94 2.59 455.7830.34COMPACTOR, TRENCH ROLLER, VIBRATORY, 33.5"W X 19.7"DIA, DOUBLE TAMPING FOOT DRUMS, WALK BEHIND, 18,000 LBS IMPACT

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-63


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

RAMMAX MACHINERY CO.

8P23/16FMC10RX001 $29,907 6.36 0.62 1.09 163.8019.26COMPACTOR, TRENCH ROLLER, VIBRATORY, 23"W X 14.6"DIA, QUAD PADFOOT DRUMS, WALK BEHIND, 7,875 LBS IMPACT

HP D-off

14P33/24FMRC10RX002 $41,319 8.78 0.85 1.91 305.2427.06COMPACTOR, TRENCH ROLLER, VIBRATORY, 33"W X 21.7"DIA, QUAD PADFOOT DRUMS, WALK BEHIND, 15,652 LBS IMPACT

HP D-off

33P47/40KMC10RX003 $69,170 14.70 1.43 4.50 668.7846.75COMPACTOR, TRENCH ROLLER, VIBRATORY, 47"W X 22"DIA, QUAD PADFOOT DRUMS, RIDE ON, 21,600 LBS IMPACT

HP D-off

WACKER CORPORATION

11RSS800AC10WC010 $9,601 2.04 0.20 2.68 111.228.78COMPACTOR, ROLLER, VIBRATORY, 28"W X 22"DIA, SINGLE SMOOTH DRUM, WALK BEHIND, 3,400 LBS IMPACT

HP G

9RD7HC10WC017 $12,707 2.70 0.26 1.23 161.619.03COMPACTOR, ROLLER, VIBRATORY,25.5"W X 16.5"DIA, DOUBLE SMOOTH DRUM, WALK BEHIND, 2,925 LBS IMPACT

HP D-off

20RT 56-SCC10WC019 $29,835 6.34 0.62 2.73 313.7921.05COMPACTOR, ROLLER, VIBRATORY, 22"W X 20"DIA, DOUBLE SMOOTH DRUM, WALK BEHIND, 7,000/14,000 LBS IMPACT

HP D-off

20RT 82-SCC10WC016 $31,468 6.69 0.65 2.73 334.0022.03COMPACTOR, TRENCH ROLLER, VIBRATORY, 32"W X 20"DIA, DOUBLE TAMPING FOOT DRUMS, WALK BEHIND, 7,000/14,000 LBS IMPACT

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-64


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

CONCRETE CLEANERS / ABRASIVE BLASTERSC150.10 WALK BEHINDSUBCATEGORY

US FILTER/BLASTRAC

21-8 & TURBO VAC

C15BL001 $9,905 1.98 0.21 0.20 21.205.76CONCRETE BLASTER CLEANING SYSTEM, WALK BEHIND, 8" PATH (ADD 4 KVA GENERATOR & BLAST MEDIA COST)

HP E

101-10D & 6-54 DCC15BL003 $47,458 9.49 1.00 0.99 75.7526.75CONCRETE BLASTER CLEANING SYSTEM, WALK BEHIND, 10" PATH (ADD 30 KVA GENERATOR & BLAST MEDIA COST)

HP E

151-15D & 6-54-DCC15BL004 $55,538 11.11 1.17 1.49 86.7331.83CONCRETE BLASTER CLEANING SYSTEM, WALK BEHIND, 15" PATH (ADD 30 KVA GENERATOR & BLAST MEDIA COST)

HP E

302-20D & 8-54-DCC15BL005 $81,407 16.28 1.72 2.98 129.8647.36CONCRETE BLASTER CLEANING SYSTEM, WALK BEHIND, 20" PATH (ADD 75 KVA GENERATOR & BLAST MEDIA COST)

HP E

EQUIPMENT DEVELOPMENT CO., INC. (EDCO)

9CPM-8C15ED002 $4,474 0.89 0.09 1.71 20.544.19CONCRETE GRINDER, WALK BEHIND, TRAFFIC LINE REMOVER, 8'' CUTTING PATH

HP G

11TLR-7C15ED001 $7,211 1.44 0.15 2.09 50.876.00CONCRETE GRINDER, WALK BEHIND, TRAFFIC LINE REMOVER, 7'' CUTTING WIDTH

HP G

0.20 TRUCK/TRAILER MOUNTEDSUBCATEGORY

US FILTER/BLASTRAC

3504800C15BL006 $4,083 0.41 0.08 49.93 2550.2957.63CONCRETE BLASTER, SELF PROPELLED, 48'' PATH

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-65


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)


86C15XX001 $132,198 13.05 2.53 28.05 1389.0665.97180 HP D-offCONCRETE CLEANER/ABRASIVE BLASTER, TRUCK MOUNTED, GINDER/BLASTER, 4" - 16" CLEANING PATH WIDTH

HP D-on

CONCRETE BUGGIESC200.00 CONCRETE BUGGIESSUBCATEGORY

WACKER CORPORATION

13WB 16AC20WC002 $11,423 2.09 0.24 2.47 131.297.69CONCRETE BUGGY, 16 CF BUCKET, 2,500 LBS, WALK & RIDE, 4X2

HP G


810GC20XX001 $8,013 1.48 0.17 1.52 100.915.17CONCRETE BUGGY, 10 CF BUCKET, 1,500 LBS

HP G

CONCRETE FINISHERS/SCREEDS/SPREADERSC250.10 FINISHERS/TROWELSSUBCATEGORY

ALLEN ENGINEERING CORP.

20PRO 900C25AJ015 $12,208 1.95 0.25 3.79 71.238.98CONCRETE TROWEL, RIDING, 2 - 36" DIA ROTORS, 8 BLADES

HP G


HP G


HP G

28SUPER PRO 400C25AJ019 $21,521 3.44 0.44 5.31 132.1614.25CONCRETE TROWEL, RIDING, 2 - 46" DIA ROTORS, 8 BLADES

HP G

EP 1110-1-8, Vol. 130 Nov 09

2-66


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

STOW MANUFACTURING, INC.

8SCT36H80C25ST001 $2,536 0.41 0.05 1.52 30.262.71CONCRETE FINISHER, WALK BEHIND, ROTO TROWEL, 36" DIA ROTOR, 4 BLADES

HP G

9SCT46H80C25ST002 $2,600 0.42 0.05 1.71 30.262.95CONCRETE FINISHER, WALK BEHIND, ROTO TROWEL, 46" DIA ROTOR, 4 BLADES

HP G

WACKER CORPORATION

8CT48ADPC25WC002 $3,146 0.50 0.06 1.52 30.312.93CONCRETE FINISHER, WALK BEHIND, POWER TROWEL, 48" DIA ROTOR, 4 BLADES

HP G

0.20 VIBRATORY SCREEDSUBCATEGORY


612HEDC25AJ003 $6,481 1.04 0.13 1.14 50.653.76CONCRETE, VIBRATORY SCREED, 12.5' WIDE

HP G

612 HDC25AJ001 $4,587 0.73 0.09 1.14 40.463.04CONCRETE, VIBRATORY SCREED, 20' WIDE

HP G

812HEDC25AJ004 $9,267 1.48 0.19 1.52 80.935.25CONCRETE, VIBRATORY SCREED, 30' WIDE

HP G


HP G


HP G


HP G

EP 1110-1-8, Vol. 130 Nov 09

2-67


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

0.25 VIBRATORY LASER SCREEDSUBCATEGORY

SOMERO ENTERPRISES, INC.

30S-100C25SV003 $142,708 12.33 2.91 2.95 729.0832.15CONCRETE, VIBRATORY LASER SCREED, 8' WIDE X 12' BOOM

HP D-off

65SXP (VERSATILE)

C25SV002 $284,056 24.68 5.78 6.39 12618.1264.54CONCRETE, VIBRATORY LASER SCREED, 8' WIDE X 20' BOOM

HP D-off

65SXP (PRODUCTIVE)

C25SV001 $302,287 26.23 6.15 6.39 15119.2768.23CONCRETE, VIBRATORY LASER SCREED, 12' WIDE X 20' BOOM

HP D-off

0.30 MATERIAL/TOPPING SPREADERSSUBCATEGORY


6SP23HC25AJ008 $15,621 1.37 0.32 0.98 111.014.32CONCRETE, MATERIAL/TOPPING SPREADER, 12.5' WIDE

HP G

6SP23HC25AJ009 $16,588 1.45 0.34 0.98 121.074.51CONCRETE, MATERIAL/TOPPING SPREADER, 20' WIDE

HP G


HP G


HP G


HP G


HP G

EP 1110-1-8, Vol. 130 Nov 09

2-68


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

CONCRETE GUNITERS / SHOTCRETERSC350.00 CONCRETE GUNITERS / SHOTCRETERSSUBCATEGORY

AIRPLACO EQUIPMENT CO., INC.

9C-10SLC35AF002 $14,422 1.52 0.29 0.00 61.056.11CONCRETE GUNITER/SHOTCRETER, DRY/SEMI-WET, HOPPER/PUMP/SPRAY, 12 CY/HR, 2" HOSE & 1 GUN (ADD 600 CFM COMPRESSOR)

CFM A

6001900 HD NUCRETOR

C35AF001 $26,517 2.81 0.53 0.00 111.947.86CONCRETE GUNITER/SHOTCRETER, DRY MIX, 2 - 15 CY/HR, W/2 PRESSURIZED TANKS/ 100' - 2" DIA HOSE (ADD 600 CFM COMPRESSOR)

CFM A

30634 Mix ElevatorC35AF004 $42,284 4.49 0.85 3.42 453.1017.95CONCRETE GUNITER/SHOTCRETER, DRY BATCH MIXER, 13 CY/HR, W/FEEDER, TRAILER MTD (ADD SHOTCRETE MACHINE)

HP D-off

54734 Mix ElevatorC35AF005 $63,131 6.67 1.26 6.16 814.6026.97CONCRETE GUNITER/SHOTCRETER, DRY BATCH MIXER, W/20 CY/HR ELEVATOR FEEDER/ 45 CF SAND HOPPER/ 4 CF CEMENT HOPPER/ & PREDAMPENING SPRAY BAR, TRAILER MTD (ADD SHOTCRETE MACHINE)

HP D-off

ALLENTOWN EQUIPMENT

5GRH-610 ROTARY GUN

C35AL003 $15,199 1.47 0.30 0.53 111.045.24CONCRETE GUNITER/SHOTCRETER, ROTARY PUMP, WET/DRY, 1 - 6 CY/HR, W/HOPPER/ 100' - 1.5" DIA HOSE/ & NOZZLE, CART MTD, (ADD 250 - 600 CFM COMPRESSOR)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-69


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

C35 ALLENTOWN EQUIPMENT (continued)9AG-15

AUTOMATIC GUN

C35AL013 $12,892 1.30 0.26 0.00 150.914.04CONCRETE GUNITER/SHOTCRETER, ROTARY PUMP, WET/DRY, 3 - 15 CY/HR, W/HOPPER/ 100' - 1.5" DIA HOSE/ & NOZZLE (ADD 300 - 900 CFM COMPRESSOR)

CFM A

9N-2 PNEUMATIC GUN

C35AL008 $24,842 2.66 0.50 0.00 131.837.40CONCRETE GUNITER/SHOTCRETER, DRY MIX, 2 - 8 CY/HR, W/2 PRESSURIZED TANKS/ 100' - 1.5" DIA HOSE/ & NOZZLE (ADD 200 - 900 CFM COMPRESSOR)

CFM A

30R-900 BATCH MIX RIG

C35AL002 $42,698 4.42 0.85 3.42 473.0616.98CONCRETE GUNITER/SHOTCRETER, DRY BATCH MIXER, 10 TON/HR, W/ELEVATOR FEEDER/ 20 CF CEMENT HOPPER/ 8 CF MIXER/ & PREDAMPENING SPRAY BAR, TRAILER MTD (ADD SHOTCRETE MACHINE OR ROTARY PUMP)

HP D-off

61POWER CRETER 10

C35AL014 $65,184 6.94 1.30 6.96 304.7726.99CONCRETE GUNITER/SHOTCRETER, GROUT/MUD JACK/ SHOTCRETE, 10 CY/HR, 2,085 PSI, W/30 GAL HOPPER/ 74 GAL MIXER, TRAILER MTD (ADD 3" HOSE LINE)

HP D-off

ALIVA LTD.

7AL 246C35AV008 $27,770 2.98 0.56 0.75 92.0511.10CONCRETE GUNITER/SHOTCRETER, DRY/SEMI-WET, 1.4 - 2.3 CY/HR, W/1 GAL HOPPER/ ROTARY PUMP/ 100' - 1.5" DIA HOSE/ NOZZLE/ & AIR COMPRESSOR

HP E

16AL 252C35AV009 $33,826 3.62 0.68 1.70 182.4914.28CONCRETE GUNITER/SHOTCRETER, DRY/SEMI-WET, 5 - 10 CY/HR, W/4.2 GAL HOPPER/ ROTARY PUMP/ 100' - 2.36" DIA HOSE/ NOZZLE/ & AIR COMPRESSOR

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-70


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

C35 ALIVA LTD. (continued)26AL 262C35AV010 $60,992 6.53 1.22 2.77 274.4923.68CONCRETE GUNITER/SHOTCRETER,

WET/DRY, 9 - 13 CY/HR, W/4.2 GAL HOPPER/ ROTARY PUMP/ 100' - 2.36" DIA HOSE/ NOZZLE/ & AIR COMPRESSOR

HP E

20AL 285C35AV006 $93,207 9.91 1.87 2.13 336.8331.89CONCRETE GUNITER/SHOTCRETER, WET/DRY, 11 - 27.5 CY/HR, W/6.6 GAL HOPPER/ ROTARY PUMP/ 100' - 2.55" DIA HOSE/ NOZZLE/ & AIR COMPRESSOR

HP E

12AL 302C35AV011 $46,962 5.03 0.94 1.28 503.4617.38CONCRETE GUNITER/SHOTCRETER, SHOTCRETE HYDRAULIC SPRAYER ARM, 25.6 ' HIGH (ADD TRUCK OR SMALL TRAILER & SHOTCRETE UNIT)

HP E

20AL 307C35AV012 $139,817 14.98 2.80 2.13 6810.2945.74CONCRETE GUNITERS / SHOTCRETERS, SHOTCRETE HYDRAULIC SPRAYER ARM, 52.5' HIGH (ADD TRUCK OR SMALL TRAILER & SHOTCRETE UNIT)

HP E

CONCRETE MIXING UNITSC400.00 CONCRETE MIXING UNITSSUBCATEGORY

CEMEN TECH

10SCD2-50HC40CC001 $25,865 4.14 0.53 0.99 232.6011.36CONCRETE MIXERS, STATIONARY CONCRETE DISPENSER, 15 CY/HR, 2 - 4.5 CY MATERIAL CAPACITY

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-71


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

MULTIQUIP, INC.

8WM 70SH8C40MU001 $3,172 0.48 0.06 1.52 80.302.92CONCRETE MIXERS, MIXER, PLASTER/MORTAR, 7 CF, TRAILER MTD

HP G

13WM 120SHHC40MU002 $6,428 1.00 0.13 2.47 110.635.26CONCRETE MIXERS, MIXER, PLASTER/MORTAR, 12 CF, TRAILER MTD

HP G

8MC 64SH8C40MU003 $3,210 0.48 0.07 1.52 70.312.94CONCRETE MIXERS, MIXER, CONCRETE, 6 CF, TRAILER MTD

HP G

8MC 94SH8C40MU004 $3,661 0.55 0.07 1.52 80.353.10CONCRETE MIXERS, MIXER, CONCRETE, 9 CF, TRAILER MTD

HP G


1CMS44EC40ST001 $2,153 0.31 0.04 0.05 50.201.06CONCRETE MIXERS, MIXER, CONCRETE, 4 CF, TRAILER MTD

HP E

6CMS44HC40ST002 $2,355 0.34 0.05 1.04 50.222.06CONCRETE MIXERS, MIXER, CONCRETE, 4 CF, TRAILER MTD

HP G


HP E


HP E


28EC40XX001 $3,443 0.55 0.07 0.20 70.351.82CONCRETE MIXERS, MIXER, PLASTER/MORTAR, 8 CF, ELECTRIC, PORTABLE

HP E

78GC40XX002 $3,682 0.59 0.07 1.33 70.372.92CONCRETE MIXERS, MIXER, PLASTER/MORTAR, 8 CF, GAS, PORTABLE

HP G

EP 1110-1-8, Vol. 130 Nov 09

2-72


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

C40 NO SPECIFIC MANUFACTURER (continued)310EC40XX003 $5,252 0.84 0.11 0.30 90.532.67CONCRETE MIXERS, MIXER,

PLASTER/MORTAR, 10 CF, ELECTRIC, PORTABLE

HP E


HP G


HP E


HP E


HP G

CONCRETE PAVING MACHINESC450.00 CONCRETE PAVING MACHINESSUBCATEGORY

GOMACO CORPORATION

36C-450C45GO026 $54,340 7.25 1.08 7.37 644.7128.05CONCRETE PAVING MACHINES, CYLINDER FINISHER, SINGLE DRUM, FINISHING WIDTH 9'-137'

HP G

50C-650-FC45GO027 $69,078 9.21 1.37 5.71 915.9831.33CONCRETE PAVING MACHINES, CYLINDER FINISHER, DOUBLE DRUM, FINISHING WIDTH 19'-51'

HP D-off

50C-650-SC45GO028 $109,893 14.65 2.18 5.71 1269.5146.01CONCRETE PAVING MACHINES, CYLINDER FINISHER, DOUBLE DRUM, FINISHING WIDTH 19'-51'

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-73


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

C45 GOMACO CORPORATION (continued)36C-750C45GO029 $73,064 9.74 1.45 7.37 916.3234.78CONCRETE PAVING MACHINES,

CYLINDER FINISHER, DOUBLE DRUM, FINISHING WIDTH 8'-156'

HP G

92GT-3200C45GO013 $125,859 16.78 2.49 10.50 13010.8857.18CONCRETE PAVING MACHINES, CURB/GUTTER SLIPFORM PAVER, CRAWLER, 3-TRACK, 36" WIDE MOLD/FORM

HP D-off

92COMMANDER II /GT6200

C45GO010 $151,744 20.23 3.01 10.50 20013.1366.50CONCRETE PAVING MACHINES, CURB/GUTTER SLIPFORM PAVER, CRAWLER, 2-TRACK, 36'' WIDE MOLD/FORM

HP D-off

98GT-3600C45GO014 $173,559 23.14 3.44 11.18 21015.0175.12CONCRETE PAVING MACHINES, CURB/GUTTER SLIPFORM PAVER, CRAWLER, 3-TRACK, 24'' WIDE MOLD/FORM

HP D-off

185COMMANDER III/GT6300

C45GO011 $233,685 31.16 4.63 21.11 30020.21108.00CONCRETE PAVING MACHINES, CURB/GUTTER SLIPFORM PAVER, CRAWLER, 3-TRACK, 36'' WIDE MOLD/FORM

HP D-off

169COMMANDER IIIC45GO012 $312,872 41.72 6.20 19.29 36927.06134.44CONCRETE PAVING MACHINES, CURB/GUTTER SLIPFORM PAVER, CRAWLER , 4-TRACK, 36'' WIDE MOLD/FORM

HP D-off

230GP-2600C45GO016 $341,801 45.57 6.77 26.25 75029.56152.72CONCRETE PAVING MACHINES, SLIPFORM PAVER, CRAWLER, 2-TRACK, 24'-32' PAVING WIDTH

HP D-off

335GHP-2800C45GO018 $426,001 56.80 8.44 38.23 70036.84196.60CONCRETE PAVING MACHINES, SLIPFORM PAVER, CRAWLER, 2-TRACK, 24'-32' PAVING WIDTH

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-74


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

C45 GOMACO CORPORATION (continued)450GP-4000C45GO020 $509,517 67.94 10.10 51.35 88044.07241.52CONCRETE PAVING MACHINES,

SLIPFORM PAVER, CRAWLER, 2-TRACK, 12'-50' PAVING WIDTH

HP D-off

3859500C45GO031 $413,891 55.19 8.20 43.94 72935.80198.72CONCRETE PAVING MACHINES, TRIMMER/PLACER, W/16'-8'' TRIMMER HEAD

HP D-off

MILLER SPREADER CO.

15MC 650C45MJ001 $7,377 0.98 0.15 3.07 80.646.19CONCRETE PAVING MACHINES, CURB BUILDER, SLIPFORM PAVER, 6.1 CF HOPPER 6" AUGER

HP G

M-B-W, INC.

26C101C45MW00 $45,484 6.01 0.90 2.97 273.9119.72CONCRETE PAVING MACHINES, CURB ONLY SLIPFORM PAVER, RUBBER TIRED, 12"

HP D-off

26CG200C45MW00 $57,762 7.62 1.14 2.97 344.9524.11CONCRETE PAVING MACHINES, CURB/GUTTER SLIPFORM PAVER, RUBBER TIRED, 48"

HP D-off

CONCRETE PUMPSC550.00 CONCRETE PUMPSSUBCATEGORY

MAYCO PUMP - MULTIQUIP INC.

46C-30HDGC55M3001 $23,148 2.57 0.42 8.72 271.7116.62CONCRETE PUMP, 25 CY/HR, SINGLE, TRAILER MTD

HP G

60LS-400C55M3002 $51,915 5.84 0.93 6.47 423.8522.11CONCRETE PUMP, 45 CY/HR, SINGLE, TRAILER MTD

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-75


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

C55 MAYCO PUMP - MULTIQUIP INC. (continued)

106LS-600C55M3003 $61,049 6.87 1.10 11.42 474.5430.33CONCRETE PUMP, 70 CY/HR, SINGLE, TRAILER MTD

HP D-off

OLIN ENGINEERING, INC.

7410 22C55OE006 $49,098 5.46 0.88 7.98 443.6122.99CONCRETE PUMP, 22 CY/HR,TRAILER MTD (OPEN LOOP HYDRAULIC SYSTEM)

HP D-off

12720 80C55OE009 $92,716 10.30 1.67 13.69 726.8241.83CONCRETE PUMP, 76 CY/HR, TRAILER MTD TANDEM (CLOSED LOOP HYDRAULIC SYSTEM)

HP D-off

18115 95C55OE011 $85,800 9.52 1.54 19.51 706.3046.46CONCRETE PUMP, 100 CY/HR, TRAILER MTD TANDEM (OPEN LOOP HYDRAULIC SYSTEM)

HP D-off

18120 100C55OE012 $108,927 12.12 1.96 19.51 818.0253.05CONCRETE PUMP, 100 CY/HR, TRAILER MTD TANDEM (CLOSED LOOP HYDRAULIC SYSTEM)

HP D-off

4Z 26XC55OE001 $260,185 29.27 4.68 0.00 10019.3274.08CONCRETE PUMP, PUMP & BOOM, 130 CY/HR, REACH: 72' HORIZONTAL / 85' VERTICAL (ADD 50,000 GVW TRUCK)

4Z 36XC55OE002 $334,026 37.58 6.01 0.00 10024.8095.11CONCRETE PUMP, PUMP & BOOM, 182 CY/HR, REACH: 104' HORIZONTAL / 118' VERTICAL (ADD 50,000 GVW TRUCK)

5RZ 47IC55OE003 $508,559 57.21 9.14 0.00 10037.75144.80CONCRETE PUMP, PUMP & BOOM, 182 CY/HR, REACH: 134' HORIZONTAL / 152' VERTICAL (ADD 50,000 GVW TRUCK)

SCHWING AMERICA INC.

80WP750 D-18XC55SC001 $70,380 7.88 1.27 8.62 695.2129.79CONCRETE PUMP, 70 CY/HR, 1,100 PSI, TRAILER MTD

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-76


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

C55 SCHWING AMERICA INC. (continued)177BPA 2000HDD-

20RC55SC002 $172,502 19.27 3.10 19.08 11512.7470.66CONCRETE PUMP, 67 CY/HR, 1,565 PSI,

TRAILER MTD HP D-off

210S 28XC55SC005 $362,534 40.35 6.52 26.49 35926.70133.15CONCRETE PUMP, 117 CY/HR, 75' BOOM, TRUCK MTD

HP D-on

210KVM 32XGC55SC006 $432,743 48.25 7.78 26.49 47031.91153.14CONCRETE PUMP, 117 CY/HR, 92' BOOM, TRUCK MTD

HP D-on

CONCRETE SAWS (Add cost for sawblade wear)C600.00 CONCRETE SAWS (Add cost for sawblade wear)SUBCATEGORY

CUSHION CUT, INC.

66FS 6600 D 18C60CQ011 $21,738 3.26 0.41 9.00 192.0418.76CONCRETE SAW, 6.5" DEPTH, SELF PROPELLED, 14" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP D-off

9FS 9BC60CQ002 $2,845 0.43 0.05 2.19 20.273.59CONCRETE SAW, 5.625" DEPTH, MANUAL, 16" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G

13FS 13BUCC60CQ003 $3,063 0.46 0.06 3.17 20.294.80CONCRETE SAW, 5.625" DEPTH, MANUAL, 16" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G

35FS 3500 G 18C60CQ001 $12,588 1.89 0.24 8.53 101.1914.55CONCRETE SAW, 6.5" DEPTH, SELF-PROPELLED, 18" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G

30FS 3500 E 26C60CQ014 $13,531 2.03 0.25 3.83 91.2710.94CONCRETE SAW, 10.625" DEPTH, SELF PROPELLED, 26" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP E


HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-77


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

C60 CUSHION CUT, INC. (continued)35FS 3500 G 30C60CQ010 $13,033 1.95 0.24 8.53 121.2214.70CONCRETE SAW, 12.125" DEPTH, SELF

PROPELLED, 30" BLADE,W/TRANSAXLE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G


HP D-off

84FS 8400/36C60CQ016 $27,743 4.16 0.52 11.45 202.6023.91CONCRETE SAW, 14.875" DEPTH, SELF PROPELLED, 36" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP D-off

FELKER (TARGET)

2S80/14ZC60FE002 $1,468 0.22 0.03 0.49 10.141.11CONCRETE SAW, 5.00" DEPTH, MANUAL, 14" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G

9ES 1409C60FE006 $3,066 0.46 0.06 2.19 20.293.67CONCRETE SAW, 4.625" DEPTH, WALK BEHIND, 14" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G

13ES 1413C60FE007 $3,210 0.48 0.06 3.17 20.304.85CONCRETE SAW, 4.625" DEPTH, WALK BEHIND, 14" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G

20ECII20HC60FE009 $10,251 1.54 0.19 4.88 60.969.46CONCRETE SAW, 7.50" DEPTH, SELF PROPELLED, 20" BLADE (ADD COST FOR SAWBLADE WEAR & WATER)

HP G

BOART LONGYEAR COMPANY

13FS 13BC60LY005 $3,011 0.45 0.06 3.17 20.294.78CONCRETE SAW, 7.00" DEPTH, WALK BEHIND(ADD COST FOR SAWBLADE WEAR & WATER)

HP G

EP 1110-1-8, Vol. 130 Nov 09

2-78


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

C60 BOART LONGYEAR COMPANY (continued)10360-10APC60LY001 $26,209 3.93 0.49 2.44 22.4612.62CONCRETE SAW, RAIL SAW, 15.50"

DEPTH, WALL (ADD COMPRESSOR & COST FOR SAWBLADE WEAR & WATER)

HP G

35360-35HMC60LY002 $38,758 5.81 0.72 8.53 23.6324.33CONCRETE SAW, RAIL SAW, 24.50" DEPTH, WALL(ADD COST FOR SAWBLADE WEAR & WATER)

HP G

32WR-400C60LY011 $74,924 11.24 1.40 4.36 157.0233.20CONCRETE SAW, WIRE SAW SYSTEM, HEAVY DUTY (ADD COST FOR SAW WIRE WEAR & WATER)

HP D-off

CONCRETE VIBRATORSC650.00 CONCRETE VIBRATORSSUBCATEGORY


1SV-1 115VC65ST007 $890 0.20 0.02 0.09 10.121.09CONCRETE VIBRATOR, 1.375" HEAD, 21' SHAFT (ADD 2KV GENERATOR)

HP E

2SV-2 115VC65ST008 $930 0.21 0.02 0.18 10.131.27CONCRETE VIBRATOR, 2.175" HEAD, 21' SHAFT (ADD 2KV GENERATOR)

HP E

3SV-3 115VC65ST009 $1,099 0.25 0.02 0.28 10.151.60CONCRETE VIBRATOR, 2.625" HEAD, 21' SHAFT (ADD 2KV GENERATOR)

HP E

6G55HC65ST013 $2,029 0.46 0.04 0.98 20.273.28CONCRETE VIBRATOR, 2.325" HEAD, 21' SHAFT, W/GAS MOTOR ON CART

HP G

WACKER CORPORATION

5A 5000C65WC005 $1,850 0.42 0.04 0.89 10.253.00CONCRETE VIBRATOR, 1.75" HEAD, 13' SHAFT, W/GAS MOTOR ON CART

HP G

EP 1110-1-8, Vol. 130 Nov 09

2-79


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

C65 WACKER CORPORATION (continued)3M 3000C65WC004 $969 0.22 0.02 0.28 10.131.60CONCRETE VIBRATOR, 1.75" HEAD, 13'

SHAFT, HI-FREQ INTERNAL (ADD 2KV GENERATOR)

HP E

2IREN 57C65WC003 $1,516 0.34 0.03 0.18 10.202.03CONCRETE VIBRATOR, 2.50" HEAD, 16.5' SHAFT, HI-FREQ INTERNAL (ADD 2KV GENERATOR)

HP E

CRANES, HYDRAULIC, SELF-PROPELLEDC750.00 CRANES, HYDRAULIC, SELF-PROPELLEDSUBCATEGORY

BRODERSON MANUFACTURING CORPORATION

38IC-20-1FC75BD007 $60,579 3.64 1.07 7.78 632.8917.92CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 2.5 TON, 15' BOOM, 4X2

HP G

42IC-35-2CC75BD008 $80,538 4.85 1.42 8.60 783.8521.78CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 4.0 TON, 19.2' BOOM, 4X2

HP G

42IC-35-2CC75BD004 $83,876 5.02 1.48 8.60 793.9922.40CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 4.0 TON, 19' BOOM, 4X2, NON-ROTATING OPERATOR'S CAB

HP G

69IC-80-3GC75BD009 $108,901 6.51 1.92 14.12 1725.1832.45CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 8.5 TON, 30' BOOM, 4X2

HP G

69IC-80-1GC75BD005 $105,424 6.30 1.86 14.12 1635.0131.95CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 9.0 TON, 20' BOOM, 4X2, NON-ROTATING OPERATOR'S CAB

HP G

110IC-200-3FC75BD006 $153,849 9.17 2.72 22.51 3087.3148.91CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 15.0 TON, 50' BOOM, 4X2, NON-ROTATING OPERATOR'S CAB

HP G

85IC-250-3AC75BD010 $181,798 10.87 3.21 9.70 3848.6538.13CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 18.0 TON, 50' BOOM, 4X4

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-80


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

C75 BRODERSON MANUFACTURING CORPORATION (continued)

130RT-300-2BC75BD011 $241,304 14.43 4.26 14.84 47311.4853.58CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 15.0 TON, 60' BOOM, 4X4, 20'0" OFFSET

HP D-off

GROVE CRANES (MANITOWOC)

62YB4410C75GV021 $121,581 7.28 2.15 12.69 1735.7932.71CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 10 TON, 30' BOOM, 4X4, NON-ROTATING OPERATOR'S CAB

HP G

110YB4415XTC75GV022 $150,604 8.97 2.66 12.55 3137.1536.88CRANES, HYDRAULIC, SELF-PROPELLED, YARD, 15 TON, 52' BOOM, 4X4, NON-ROTATING OPERATOR'S CAB

HP D-off

152RT525EC75GV028 $283,052 16.83 5.00 17.35 50013.4263.40CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 25 TON, 75' BOOM, 4X4X4

HP D-off

152RT530EC75GV023 $293,713 16.71 5.19 17.35 58013.5571.19CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 30 TON, 95' BOOM, 4X4

HP D-off

173RT640EC75GV024 $448,718 26.12 7.93 19.74 65020.9996.54CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 40 TON, 105' BOOM 4X4

HP D-off

240RT750EC75GV019 $517,475 29.67 9.14 27.39 87623.98120.02CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 50 TON, 110' BOOM, 4X4

HP D-off

240RT760C75GV014 $517,777 29.69 9.15 27.39 90924.00120.07CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 60 TON, 110' BOOM, 4X4, W/HOOK BLOCK & BALL

HP D-off

250RT875CC75GV025 $822,172 48.17 14.52 28.53 1,09138.61164.90CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 70 TON, 110' BOOM 4X4

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-81


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

C75 GROVE CRANES (MANITOWOC) (continued)250RT875 BXLC75GV020 $827,073 48.67 14.61 28.53 1,11938.95165.01CRANES, HYDRAULIC, SELF-PROPELLED,

ROUGH TERRAIN, 90 TON, 138' BOOM, 4X4

HP D-off

300RT9130EC75GV016 $1,178,123 69.98 20.81 34.24 1,36455.80222.75CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 100 TON, 160' BOOM, 4X4, W/HOOK BLOCK & BALL

HP D-off

PETTIBONE MICHIGAN LLC

18540RSC75PB002 $473,800 28.23 8.37 21.11 49622.4995.07CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 20 TON, 64.1' BOOM, 4X4X4

HP D-off

TADANO AMERICA CORPORATION

180TR-300XL-4C75TD003 $381,028 22.70 6.73 20.54 53718.0882.34CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 30 TON, 112' BOOM, 4X4

HP D-off


HP D-off


HP D-off

TEREX CORPORATION

130RT230C75TE001 $358,491 21.50 6.33 14.84 56317.0870.95CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 30 TON, 94' BOOM, 4X4

HP D-off

152RT335/40C75TE002 $493,036 29.50 8.71 17.35 63423.4694.53CRANES, HYDRAULIC, SELF-PROPELLED, ROUGH TERRAIN, 40 TON, 94' BOOM, 4X4

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-82


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

CRANES, HYDRAULIC, TRUCK MOUNTEDC800.01 UNDER 26 TONSUBCATEGORY

TEREX CORPORATION

130CD225C80TE008 $281,645 16.66 4.98 12.78 52513.3154.55CRANES, HYDRAULIC, TRUCK MTD, ROUGH TERRAIN, 25 TON, 72' BOOM, 4X4

HP D-off


2451700C80XX001 $143,391 8.48 2.53 24.08 3306.7747.47CRANES, HYDRAULIC, TRUCK MTD, BOOM TRUCK, 17 TON, 80' BOOM, 4X2

HP D-off

3002300C80XX002 $188,778 11.11 3.33 29.48 6008.8960.10CRANES, HYDRAULIC, TRUCK MTD, BOOM TRUCK, 23.5 TON, 102' BOOM, 6X2

HP D-off

0.02 26 TON THRU 65 TONSUBCATEGORY


300TMS-500EC80GV025 $453,418 23.88 7.94 29.48 54019.8889.42CRANES, HYDRAULIC, TRUCK MTD, 40 TON, 95' BOOM, 6X4

HP D-off

400TMS-700EC80GV006 $694,844 36.65 12.17 39.31 77130.50130.19CRANES, HYDRAULIC, TRUCK MTD, 50 TON, 110' BOOM, 8X4

HP D-off

400TMS750EC80GV029 $698,758 36.68 12.24 39.31 94730.58131.47CRANES, HYDRAULIC, TRUCK MTD, 50 TON, 110' BOOM, 8X4X4

HP D-off

348GMK 3050C80GV026 $685,087 36.02 12.00 34.20 74530.01123.75CRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 55 TON, 125' BOOM, 8X4

HP D-off

400TMS760EC80GV030 $699,952 36.74 12.26 39.31 94930.63131.61CRANES, HYDRAULIC, TRUCK MTD, 60 TON, 110' BOOM, 8X4X4

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-83


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

LINK-BELT CONSTRUCTION EQUIPMENT COMPANY

350HTC-8640 SLC80LI009 $558,387 29.35 9.78 34.39 57524.46108.29CRANES, HYDRAULIC, TRUCK MTD, 40 TON, 105' BOOM, 6X4X2

HP D-off

315HTC-8650 IIC80LI010 $497,779 26.06 8.72 30.96 78021.7597.26CRANES, HYDRAULIC, TRUCK MTD, 50 TON, 110' BOOM, 8X4X4

HP D-off

365HTC-8660 IIC80LI011 $573,910 30.04 10.06 35.87 83125.08112.34CRANES, HYDRAULIC, TRUCK MTD, 60 TON, 110' BOOM, 8X4X4

HP D-off

TEREX CORPORATION

250T335/40C80TE002 $364,525 19.09 6.39 24.57 49315.9473.36CRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 40 TON, 94' BOOM, 6X4

HP D-off

370T 500C80TE003 $484,427 25.31 8.49 36.36 80621.15101.86CRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 50 TON, 110' BOOM, 8X4

HP D-off

0.03 66 TON THRU 125 TONSUBCATEGORY


400TMS-870C80GV020 $879,025 41.19 15.30 39.31 9,16135.90148.57CRANES, HYDRAULIC, TRUCK MTD, 70 TON, 110' BOOM, 8X4

HP D-off

400TMS875CC80GV031 $791,879 37.00 13.78 39.31 81732.28138.78CRANES, HYDRAULIC, TRUCK MTD, 75 TON, 110' BOOM, 8X4X4

HP D-off

422GMK4090C80GV032 $1,055,430 49.16 18.37 41.47 1,18442.95176.88CRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 80 TON, 142' BOOM, 8X6X8

HP D-off


121ATF-650XLC80TD001 $736,358 34.09 12.82 18.36 1,09029.87110.16349 HP D-onCRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 65 TON, 132' BOOM, 8X8

HP D-off

158ATF-1000XLC80TD002 $917,774 42.66 15.98 22.49 1,07037.31135.92375 HP D-onCRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 100 TON, 138' BOOM, 8X8

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-84


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

0.04 OVER 125 TONSUBCATEGORY


174GMK 5240C80GV013 $2,066,712 87.07 35.80 28.23 1,18079.34273.98600 HP D-onCRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 125 TON, 197' BOOM, 10X8

HP D-off


HP D-off


HP D-off


HP D-off


533ATF-1500XLC80TD005 $1,101,749 46.06 19.08 61.71 1,33042.11197.87503 HP D-onCRANES, HYDRAULIC, TRUCK MTD, ALL TERRAIN, 150 TON, 162' BOOM, 10X8

HP D-off

CRANES, MECHANICAL, LATTICE BOOM, CRAWLER MOUNTEDC850.12 DRAGLINE, CLAMSHELL, OVER 1.0 CY THRU 2.5 CYSUBCATEGORY

LINK-BELT CONSTRUCTION EQUIPMENT CO.

263LS-208H IIC85LB019 $807,444 40.37 14.68 21.68 1,39034.87130.90CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 80 TON, 100' BOOM (ADD BUCKET)

HP D-off

TEREX CORPORATION

1505220C85TE001 $654,639 32.73 11.90 12.36 83128.27100.06CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 50 TON, 100' BOOM (ADD BUCKET)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-85


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

C85 TEREX CORPORATION (continued)2507225C85TE002 $910,972 45.55 16.56 20.61 1,25939.34143.20CRANES, MECHANICAL, LATTICE BOOM,

CRAWLER, DRAGLINE/CLAMSHELL, 85 TON, 100' BOOM (ADD BUCKET)

HP D-off

0.13 DRAGLINE, CLAMSHELL, OVER 2.5 CY THRU 5.0 CYSUBCATEGORY


284238 HYLAB 5C85LB021 $1,312,868 58.35 23.72 23.41 3,35752.90189.83CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 150 TON, 100' BOOM (ADD BUCKET)

HP D-off

237LS-248H IIC85LB022 $1,516,150 67.38 27.39 19.53 3,24261.08210.93CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 200 TON, 120' BOOM (ADD BUCKET)

HP D-off

MANITOWOC ENGINEERING CO.

350222HDC85MA001 $1,038,765 46.17 18.77 28.85 1,98841.86161.61CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 3.5 CY, 80' BOOM (ADD BUCKET)

HP D-off

340777C85MA002 $1,276,326 56.73 23.06 28.02 3,81551.43190.36CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 5.0 CY, 130' BOOM (ADD BUCKET)

HP D-off

TEREX CORPORATION

3359225C85TE003 $1,150,111 51.12 20.78 27.61 2,48246.34174.14CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 150 TON, 100' BOOM (ADD BUCKET)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-86


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

0.14 DRAGLINE, CLAMSHELL, OVER 5.0 CYSUBCATEGORY


440LS-278HC85LB023 $1,786,930 71.48 32.13 36.26 4,06467.87254.88CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 250 TON, 120' BOOM (ADD BUCKET)

HP D-off


375999C85MA003 $1,899,562 75.98 34.15 30.91 5,10072.14262.43CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 7.0 CY, 140' BOOM (ADD BUCKET)

HP D-off

340888C85MA009 $1,666,563 66.66 29.97 28.02 3,39763.30231.25CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, DRAGLINE/CLAMSHELL, 10 CY, 70' BOOM (ADD BUCKET)

HP D-off

0.22 LIFTING, 26 TON THRU 50 TONSUBCATEGORY

KOBELCO AMERICA INC.

178CK550C85KC007 $602,048 26.76 10.88 10.72 1,00124.2679.01CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 50 TON, 30' BOOM, LIFTING

HP D-off

0.23 LIFTING, 51 TON THRU 150 TONSUBCATEGORY



HP D-off


HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-87


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

C85 KOBELCO AMERICA INC. (continued)265CK1000C85KC003 $1,031,162 43.82 17.86 15.96 1,89939.77131.07CRANES, MECHANICAL, LATTICE BOOM,

CRAWLER, 100 TON, 200' BOOM, LIFTING

HP D-off


263LS-208H IIC85LB013 $830,476 35.30 14.38 15.84 1,39032.03108.86CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 80 TON, 190' BOOM, LIFTING

HP D-off

284218 HSLC85LB014 $946,678 40.23 16.40 17.11 1,79036.52123.05CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 110 TON, 230' BOOM, LIFTING

HP D-off

284238 HYLAB 5C85LB015 $1,312,868 55.80 22.74 17.11 3,35750.64163.35CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 150 TON, 240' BOOM, LIFTING

HP D-off


207LS-138H SERIES II

C85LI001 $680,237 28.91 11.78 12.47 1,46426.2488.61CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 80 TON, 40' TUBULAR BOOM, LIFTING

HP D-off


350222HDC85MA004 $1,028,046 43.69 17.81 21.08 2,35439.66136.39CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 100 TON, 210' BOOM, LIFTING

HP D-off

335555C85MA008 $1,021,804 43.43 17.70 20.18 3,12139.42134.71CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 100 TON, 260' BOOM, LIFTING

HP D-off

335555C85MA005 $964,620 41.00 16.71 20.18 2,74437.21128.42CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 150 TON, 250' BOOM, LIFTING

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-88


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

TEREX CORPORATION

184HC 80C85TE008 $689,077 29.29 11.94 11.08 1,43026.5988.06CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 80 TON, 200' BOOM, LIFTING

HP D-off

230HC 110C85TE009 $849,748 36.11 14.72 13.85 1,91132.78108.79CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 100 TON, 230' BOOM, LIFTING

HP D-off

240HC 125C85TE010 $1,126,692 47.88 19.51 14.46 2,12843.45139.92CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 125 TON, 240' BOOM, LIFTING

HP D-off

0.24 LIFTING, OVER 150 TONSUBCATEGORY


316CK2000C85KC008 $1,370,834 52.96 23.63 19.03 3,62250.11167.76CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 200 TON, 50' BOOM, LIFTING

HP D-off

279CK2500C85KC006 $1,931,116 74.61 33.28 16.80 4,98570.59225.17CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 250 TON, 280' BOOM, LIFTING

HP D-off


284248 HYLAB 5C85LB016 $1,655,560 63.96 28.53 17.11 3,24260.51196.06CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 200 TON, 280' BOOM, LIFTING

HP D-off

440LS-278HC85LB017 $1,869,968 72.25 32.23 26.50 4,06468.36229.45CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 250 TON, 330' BOOM, LIFTING

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-89


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)



HP D-off


HP D-off


HP D-off

TEREX CORPORATION

315HC 210C85TE011 $1,664,657 64.32 28.69 18.97 3,70860.85199.11CRANES, MECHANICAL, LATTICE BOOM, CRAWLER, 210 TON, 280' BOOM, LIFTING

HP D-off

CRANES, MECHANICAL, LATTICE BOOM, TRUCK MOUNTEDC900.04 OVER 125 TONSUBCATEGORY


197HC-238H IIC90LB001 $1,497,065 59.26 26.92 22.97 1,91356.55200.21430 HP D-onCRANES, MECHANICAL, LATTICE BOOM, TRUCK MTD, 150 TON, 260' BOOM, 8X4

HP D-off

248HC-248HC90LB002 $1,690,699 67.00 30.40 26.85 2,47663.90226.09430 HP D-onCRANES, MECHANICAL, LATTICE BOOM, TRUCK MTD, 200 TON, 280' BOOM, 8X4

HP D-off

430HC-278 H IIC90LB003 $2,714,827 107.65 48.81 40.69 3,385102.64359.46430 HP D-onCRANES, MECHANICAL, LATTICE BOOM, TRUCK MTD, 300 TON, 330' BOOM, 12X6

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-90


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

CRANES, TOWERC950.00 CRANES, TOWERSUBCATEGORY

PECCO AND WOLFF TOWER CRANES (MORROW)

128SK200C95AP004 $527,088 23.43 9.52 11.81 97021.2485.17TOWER CRANE, 3.4 TON @ 181' RADIUS 42.6' HEIGHT (ADD 95KW GENERATOR & T-SECTION)

HP E

S16-35 TOWER SECTION

C95AP005 $16,683 0.74 0.30 0.00 160.671.97TOWER CRANE OPTION, 1.1' T-TRANSITION S35 -S16 (ADD SK 140 - SK 225 TOWER CRANE)

S35 TOWER SECTION

C95AP006 $31,647 1.41 0.57 0.00 891.283.75TOWER CRANE OPTION, 19.33' TOWER SECTION (ADD TO SK 140 - SK 400 TOWER CRANE)

213SK400C95AP007 $833,322 37.04 15.05 19.66 1,78333.57134.90TOWER CRANE, 3.3 TON @ 245' RADIUS, 56.7' HEIGHT (ADD 160 KW GENERATOR & T-SECTION)

HP E

S35 CLIMBING UNIT

C95AP008 $127,954 5.69 2.31 0.00 2485.1615.64TOWER CRANE OPTION, 29.2' CLIMBING UNIT (ADD TO SK 200 - SK 400 TOWER CRANE)

S35-60 TOWER SECTION

C95AP009 $42,608 1.89 0.77 0.00 991.725.04TOWER CRANE OPTION, 19.4' T-TRANSITION S60 S35 (ADD SK 225 - SK 560 TOWER CRANE)

217SK560C95AP010 $1,110,640 49.36 20.07 20.03 1,55744.75168.30TOWER CRANE, 2.8 TON @ 265' RADIUS, 76.5' HEIGHT (ADD 161 KW GENERATOR &T-SECTION)

HP E

S60 TOWER SECTION


EP 1110-1-8, Vol. 130 Nov 09

2-91


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

C95 PECCO AND WOLFF TOWER CRANES (MORROW) (continued)

S60 CLIMB UNITC95AP012 $159,482 7.09 2.88 0.00 2586.4319.37TOWER CRANE OPTION, 32.8' CLIMBING UNIT (ADD TO SK 225 - SK 560 TOWER CRANE)

354SN355C95AP013 $1,064,516 47.31 19.23 32.67 2,74842.89182.98TOWER CRANE, 3.8 TON @ 197' RADIUS, 110' TALL, LUFFING (ADD 300 KW GENERATOR & T-SECTION)

HP E

SN35 TOWER SECTION

C95AP014 $36,247 1.61 0.65 0.00 891.464.28TOWER CRANE OPTION, 14.75' TOWER SECTION (ADD TO SN 141 - SN 355 TOWER CRANE)

SN35 CLIMBING UNIT

C95AP015 $139,128 6.18 2.51 0.00 2485.6016.95TOWER CRANE OPTION, 29.2' CLIMBING UNIT (ADD TO SN 141 - SN 355 TOWER CRANE)

S35N-60TOWER SECTION

C95AP016 $48,661 2.16 0.88 0.00 991.965.75TOWER CRANE OPTION, 19.4' T-TRANSITION S60 S35N (ADD SN 141 - SK 355 TOWER CRANE)

125SK140C95AP017 $450,561 20.02 8.14 11.54 1,30918.1574.68TOWER CRANE, 3.1 TON @ 151' RADIUS, 85.0' HEIGHT (ADD 95KW GENERATOR & T-SECTION)

HP E

S16 TOWER SECTION


S16 CLIMBING UNIT

C95AP019 $86,530 3.85 1.56 0.00 1653.4910.74TOWER CRANE OPTION, 29.2' CLIMBING UNIT (ADD TO SK140 - SK 200 TOWER CRANE)

223SN141C95AP020 $495,981 22.04 8.96 20.58 1,08219.9894.46TOWER CRANE, 1.6 TON @ 147' RADIUS, 89' TALL, LUFFING (ADD 200 KW GENERATOR & T-SECTION)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-92


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

C95 PECCO AND WOLFF TOWER CRANES (MORROW) (continued)

258SN160-16C95AP021 $774,956 34.44 14.00 23.81 1,17931.22133.61TOWER CRANE, 2.8 TON @ 164' RADIUS, 88' TALL, LUFFING (ADD 250 KW GENERATOR & T-SECTION)

HP E

24PH5000-12C95AP022 $117,217 5.21 2.12 2.22 1304.7318.41TOWER CRANE OPTION, 24 PERSON / 2.4 TON MATERIAL ELEVATOR/HOIST (ADD 4.9' MAST SECTION & 18 KW GENERATOR)

HP E

MAST SECTIONC95AP023 $2,767 0.12 0.05 0.00 30.110.32TOWER CRANE OPTION, 4.9' MAST-> PERSON/MATERIAL ELEVATOR/HOIST (ADD WALL TIE & CABLE GUIDE @30')

MORROW EQUIPMENT COMPANY, LLC

3597KC95LH022 $410,397 18.09 7.41 3.23 1,59316.4656.06TOWER CRANE, HORIZONTAL BOOM, JIB CRANE, 13.2 TON MAX, 1.9 TON @ 148' RADIUS, 66' HEIGHT, SELF/ERECTING, W/FIVE - 7' 10" TOWER SECTIONS/ & ROAD TRANSPORT EQUIPMENT (ADD 40KW GENERATOR)

HP E

65140KC95LH023 $572,061 25.25 10.33 6.00 1,83622.9680.65TOWER CRANE, HORIZONTAL BOOM, JIB CRANE, 11.0 TON MAX, 1.7 TON @ 180' RAD 146' HEIGHT, SELF/ERECTING, W/EIGHT - 9' 10" TOWER SECTIONS/ & ROAD TRANSPORT EQUIPMENT (ADD 60KW GENERATOR)

HP E

109132 HCC95LH003 $460,592 20.47 8.32 10.06 1,15618.5673.51TOWER CRANE, HORIZONTAL BOOM, JIB CRANE, 8.8 TON MAX, 2.4 TON @ 168' RADIUS, 147.8' HEIGHT, W/FOURTEEN - 8' 2" TOWER SECTIONS (ADD 85 KW GENERATOR)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-93


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

C95 MORROW EQUIPMENT COMPANY, LLC (continued)

148200 HCC95LH005 $598,929 26.62 10.82 13.66 1,37424.1396.62TOWER CRANE, HORIZONTAL BOOM, JIB CRANE, 11.0 TON MAX, 2.5 TON @ 201' RADIUS, 162.7' HEIGHT, W/NINE - 13' 7" TOWER SECTIONS (ADD 110 KW GENERATOR)

HP E

223390 HCC95LH011 $1,119,249 49.74 20.22 20.58 2,74445.09170.19TOWER CRANE, HORIZONTAL BOOM, JIB CRANE, 17.6 TON MAX, 3.3 TON @ 246' RADIUS, 199.1' HEIGHT, W/NINE - 19' 0" TOWER SECTIONS (ADD 170 KW GENERATOR)

HP E

223550 HC20C95LH013 $1,429,987 63.55 25.83 20.58 3,76557.61206.94TOWER CRANE, HORIZONTAL BOOM, JIB CRANE, 22.0 TON MAX, 3.8 TON @ 265' RADIUS, 237.5' HEIGHT, W/TWELVE - 19' 0" TOWER SECTIONS (ADD 170 KW GENERATOR)

HP E

317550 HC-LC95LH015 $1,905,970 84.71 34.43 29.26 5,07576.79279.08TOWER CRANE, 26.4 TON MAX, 3/4 TON @ 197' RADIUS, 210' HEIGHT, LUFFING, W/SIX 19' 0" TOWER SECTIONS (ADD 480 KW GENERATOR)

HP E

DRILLS, HYDRAULIC TRACK (Add cost for drill steel and bit wear)D100.10 DRILLS, AIR TRACK (Add cost for drill steel and bit wear)SUBCATEGORY

INGERSOLL RAND ROCK DRILL DIV

750ECM350/VL140D10IR003 $161,318 8.64 3.06 0.00 1297.3827.70DRILL, AIR TRACK, CRAWLER, 2.5-4.0" DIA, 12' FEED (ADD COST FOR DRILL STEEL AND BIT WEAR, ADD 750 CFM COMPRESSOR)

CFM A

EP 1110-1-8, Vol. 130 Nov 09

2-94


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

SULLIVAN-PALATEK, INC.

750RAM EXT, VCR360

D10SU002 $198,691 10.64 3.77 0.00 1529.0933.94DRILL, AIR TRACK, CRAWLER, 2.5-4.0" DIA, 12' FEED (ADD COST FOR DRILL STEEL AND BIT WEAR, ADD 750 CFM COMPRESSOR)

CFM A

900RAM EXT, VCR361

D10SU003 $203,621 10.91 3.86 0.00 2059.3234.77DRILL, AIR TRACK, CRAWLER, 3.0-4.0" DIA, 12' FEED (ADD COST FOR DRILL STEEL AND BIT WEAR, ADD 900 CFM COMPRESSOR)

CFM A

0.20 DRILLS, HYDRAULIC TRACK (Add cost for drill steel and bit wear)SUBCATEGORY

INGERSOLL RAND ROCK DRILL DIV

215ECM590/YH80AD10IR005 $433,831 32.54 8.41 25.90 24524.68127.57DRILL, HYDRAULIC TRACK, CRAWLER, 2.5-4.5" DIA, 14' DRIFTER TRAVEL, SELF-CONTAINED (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

SULLIVAN-PALATEK, INC.

260SCORPION VCR360

D10SU005 $221,252 16.59 4.29 31.32 26512.5985.58DRILL, HYDRAULIC TRACK, CRAWLER, 5.25" DIA, 12' FEED (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

260SCORPION VCR361

D10SU006 $223,923 16.79 4.34 31.32 26512.7486.18DRILL, HYDRAULIC TRACK, CRAWLER, 6.5" DIA, 12' FEED (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-95


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

DRILLS, HORIZONTAL BORING & GROUND PIERCING (Add cost for drill steel and bit wear)D150.00 DRILLS, HORIZONTAL BORING & GROUND PIERCING (Add cost for drill steel and bit wear)SUBCATEGORY

BOR-IT MANUFACTURING COMPANY INC.

1212 MIGHT MAXD15BI001 $14,975 1.12 0.29 2.60 180.856.18DRILL, HORIZONTAL BORING, 12" DIA, COMBINED HEAD 28,000 LBS THRUST, W/100' AUGER TRACK (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP G

2020 POWER HOUSE II

D15BI002 $26,818 2.01 0.52 2.41 151.538.45DRILL, HORIZONTAL BORING, 20" DIA, COMBINED HEAD 44,000 LBS THRUST, W/100' AUGER TRACK (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

3024 BRUTED15BI003 $40,594 3.04 0.79 3.61 382.3112.74DRILL, HORIZONTAL BORING, 24" DIA, COMBINED HEAD 84,000 LBS THRUST, W/100' AUGER TRACK (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

4530 POWER PLUS


HP D-off

6236 WORKHORSE


HP D-off

11948 TERMINATOR


HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-96


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

D15 BOR-IT MANUFACTURING COMPANY INC. (continued)

18954 TERMINATOR II

D15BI008 $168,656 12.65 3.27 22.77 2509.6061.76DRILL, HORIZONTAL BORING, 54" DIA, COMBINED HEAD 32,700,000 LBS THRUST, W/100' AUGER TRACK (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

18960D15BI007 $180,892 13.57 3.51 22.77 25010.3064.37DRILL, HORIZONTAL BORING, 60" DIA, COMBINED HEAD 1,100,000 LBS THRUST, W/100' AUGER TRACK (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off


MC-500HD15XX001 $8,237 0.62 0.16 0.00 100.471.76DRILL, HORIZONTAL BORING, 3" - 6" DIA, 15,000 LBS THRUST, HYDRAULIC MOTOR (ADD COST FOR DRILL STEEL AND BIT WEAR)

H-12/RM-12D15XX002 $12,394 0.93 0.24 0.00 120.712.64DRILL, HORIZONTAL BORING, 4" - 12" DIA, 24,000 LBS THRUST, HYDRAULIC MOTOR (ADD COST FOR DRILL STEEL AND BIT WEAR)

DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit wear)D200.00 DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit wear)SUBCATEGORY

ACKER DRILL COMPANY INC.

2630-ED20AD005 $5,662 0.53 0.11 0.23 10.382.03DRILL, CORE, COLUMN MOUNTED, 4" DIA MAX CORE HOLE (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP E

2930-ED20AD002 $5,757 0.54 0.11 0.23 20.382.06DRILL, CORE, COLUMN MOUNTED, 10" DIA MAX CORE HOLE (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-97


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

D20 ACKER DRILL COMPANY INC. (continued)41040-ED20AD006 $9,370 0.88 0.19 0.45 10.633.47DRILL, CORE, COLUMN MOUNTED, 10" DIA

MAX CORE HOLE (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP E

81200-GD20AD007 $15,464 1.45 0.31 0.91 31.046.13DRILL, CORE, COLUMN MOUNTED, 12" DIA MAX CORE HOLE (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP E

CUSHION CUT, INC.

16HCD24/12D20CQ001 $13,880 1.30 0.27 3.47 50.928.75DRILL, CORE, COLUMN MOUNTED, 1"-24" BIT DIA (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP G

BOART LONGYEAR COMPANY

3752D20LY001 $8,341 0.78 0.16 0.34 20.553.13DRILL, CORE, COLUMN MOUNTED, 1.5"-6" BIT DIA, W/E4-230/110 MOTOR (110V) (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP E

18542ND20LY002 $8,629 0.81 0.17 0.00 30.582.79DRILL, CORE, COLUMN MOUNTED, 0.5"-36" BIT DIA, W/A4-350 MOTOR (ADD COST FOR DRILL STEEL AND BIT WEAR AND ADD 185 CFM AIR COMPRESSOR)

CFM A

DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear)D250.00 DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear)SUBCATEGORY

ACKER DRILL COMPANY INC.

28ACEWD25AD004 $80,632 6.05 1.56 3.37 354.5922.00DRILL, CORE, SKID MTD, 725' MAX DRILL DEPTH (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-98


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

D25 ACKER DRILL COMPANY INC. (continued)69BUSH MASTERD25AD003 $101,075 7.58 1.96 8.31 455.7532.14DRILL, CORE, SKID MTD, 1500' MAX DRILL

DEPTH (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

E-Z DRILL, INC.

100210 BD25EZ002 $6,695 0.46 0.13 0.00 30.362.03DRILL, CORE, SKID MTD, 0.6''-2.5'' DIA., 18" DEPTH, HORIZONTAL DOWELLING ASSEMBLY (ADD COST FOR DRILL STEEL AND BIT WEAR, ADD 100 CFM COMPRESSOR)

CFM A

100210 B SRAD25EZ003 $7,121 0.51 0.14 0.00 30.402.12DRILL, CORE, SKID MTD, 0.6''-2.5'' DIA., 18" DEPTH, HORIZONTAL DOWELLING ASSEMBLY (ADD COST FOR DRILL STEEL AND BIT WEAR, ADD 100 CFM COMPRESSOR)

CFM A

100210 B SR HORIZONTAL

D25EZ001 $7,632 0.57 0.15 0.00 30.442.23DRILL, CORE, SKID MTD, 0.6''-2.5'' DIA., 18" DEPTH, HORIZONTAL DOWELLING ASSEMBLY (ADD COST FOR DRILL STEEL AND BIT WEAR, ADD 100 CFM COMPRESSOR)

CFM A

100210-3 SRAD25EZ005 $26,269 1.91 0.51 0.00 121.477.20DRILL, CORE, SELF PROPELLED, 0.6''-2.5'' DIA., 18" DEPTH, DOWELLING MACHINE (ADD COST FOR DRILL STEEL AND BIT WEAR, ADD 100 CFM COMPRESSOR)

CFM A

EP 1110-1-8, Vol. 130 Nov 09

2-99


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear)D300.00 DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear)SUBCATEGORY

HYDRAULIC POWER SYSTEMS, INC.

210H-15D30HD001 $76,692 5.75 1.49 25.30 1464.3748.03DRILL, AUGER, HYDRAULIC, W/60' 8" X 21" LEADS, 15,000 FT-LBS TORQUE (ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR AND CRANE)

HP D-off

270H-35VTD30HD002 $114,965 8.62 2.23 32.52 2006.5465.88DRILL, AUGER, HYDRAULIC, W/60' 8" X 27" LEADS, 33,000 FT-LBS TORQUE (ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR AND CRANE)

HP D-off

335H-50VTD30HD003 $149,608 11.22 2.90 40.35 2698.5183.59DRILL, AUGER, HYDRAULIC, W/60' 8" X 33" LEADS, 50,000 FT-LBS TORQUE (ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR AND CRANE)

HP D-off

FOREMOST MOBILE DRILLING COMPANY, INC.

8MINUTEMAND30MR001 $12,451 0.93 0.24 1.73 40.714.80DRILL, EARTH / AUGER, W/AUGER KIT, 3" DIA, 30' DEPTH, 350 FT-LBS TORQUE, PORTABLE (ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR)

HP G

58B-31D30MR003 $84,416 6.26 1.64 6.99 424.7727.01DRILL, EARTH / AUGER, HYDRAULIC AUGER, 14" DIA, 30' DEPTH, 3,500 FT-LBS TORQUE, TRAILER MOUNTED (ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-100


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

D30 FOREMOST MOBILE DRILLING COMPANY, INC. (continued)

100B-53D30MR005 $203,321 15.04 3.94 16.32 12011.4664.57230 HP D-onDRILL, EARTH / AUGER, MULTI-PURPOSE, 6" DIA, 245' DEPTH, 5,955 FT-LBS TORQUE, W/21,000 GVW TRUCK (W/PTO DRIVE)(ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR)

HP D-off

115B-58D30MR006 $209,447 15.50 4.06 18.67 13011.8168.62260 HP D-onDRILL, EARTH / AUGER, MULTI-PURPOSE, 8" DIA, 250' DEPTH, 7,000 FT-LBS TORQUE W/33,000 GVW TRUCK (ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR)

HP D-off

115B-61HTD30MR007 $264,673 19.64 5.13 18.67 20514.9581.12260 HP D-onDRILL, EARTH / AUGER, MULTI-PURPOSE, 8" DIA, 375' DEPTH, 20,000 FT-LBS TORQUE W/33,000 GVW TRUCK (ADD COST FOR DRILL STEEL AND CUTTING EDGE WEAR)

HP D-off

DRILLS, ROTARY BLASTHOLE (Add cost for drill steel and bit wear)D350.11 DIESEL, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit wear)SUBCATEGORY

DRILTECH, INC. (SANDVIK)

450D25KSD35DT001 $590,868 33.76 10.83 54.21 62027.71164.30DRILL, ROTARY BLASTHOLE, 5''-6.75'' DIA., 27,000 LB PULLDOWN, CRAWLER, 88' DEEP(ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

450D245SD35DT002 $607,349 34.71 11.13 54.21 72028.49167.10DRILL, ROTARY BLASTHOLE, 5''-8'' DIA., 40,000 LB PULLDOWN, CRAWLER, 148' DEEP (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-101


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

D35 DRILTECH, INC. (SANDVIK) (continued)450D45KSD35DT003 $687,674 39.30 12.60 54.21 1,05032.25180.74DRILL, ROTARY BLASTHOLE, 6''-9'' DIA.,

45,000 LB PULLDOWN, CRAWLER, 208' DEEP (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

525D50KSD35DT004 $730,263 41.73 13.38 63.24 1,05034.25198.62DRILL, ROTARY BLASTHOLE, 6''-9.875'' DIA., 50,000 LB PULLDOWN, CRAWLER, 148' DEEP (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

760D55SPD35DT005 $1,138,575 65.06 20.86 91.55 1,32053.39301.35DRILL, ROTARY BLASTHOLE, 6.75''-10'' DIA., 45,000 LB PULLDOWN, CRAWLER, 55' DEEP (SINGLE PASS) (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

REEDRILL (TEREX)

400SK5ADD35RD001 $445,905 25.48 8.17 54.67 52520.91140.23350 HP D-onDRILL, ROTARY BLASTHOLE, 4"-7" DIA, 12,000 LBS PULL BACK, TRUCK MTD, 148' DEEP (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

0.12 DIESEL, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear)SUBCATEGORY

DRILTECH, INC. (SANDVIK)

760D75KSD35DT006 $1,008,200 44.81 18.21 91.55 1,40040.62242.40DRILL, ROTARY BLASTHOLE, 9''-11'' DIA., 75,000 LB PULLDOWN, CRAWLER, 173' DEEP (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-102


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

INGERSOLL RAND ROTARY DRILL DIV

465T3WD35IB004 $627,455 27.65 11.34 63.06 66025.17158.42380 HP D-onDRILL, ROTARY BLASTHOLE, WATER WELL 6"-24" DIA, 30,000 LB PULL BACK, TRUCK MTD (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

475TH-60D35IB003 $658,256 29.06 11.89 64.27 60026.42163.89380 HP D-onDRILL, ROTARY BLASTHOLE, WATER WELL, 12" DIA, 26,500 LBS PULL BACK, TRUCK MTD (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

575T3W DEEPHOLED35IB005 $727,371 32.09 13.14 76.31 68829.19187.25380 HP D-onDRILL, ROTARY BLASTHOLE, WATER WELL 6"-18" DIA, 50,000 LB PULL BACK, TRUCK MTD (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

600T4WD35IB006 $764,775 33.76 13.82 77.94 68830.70194.22305 HP D-onDRILL, ROTARY BLASTHOLE, WATER WELL 6"-20" DIA, 70,000 LB PULL BACK, TRUCK MTD (ADD COST FOR DRILL STEEL AND BIT WEAR)

HP D-off

FORK LIFTSF100.00 FORK LIFTSSUBCATEGORY

JCB INC.

75930-4F10JC001 $70,725 5.51 1.33 7.37 1504.0922.15FORK LIFT, ROUGH TERRAIN, 6,000 LBS @ 28' HIGH STRAIGHT MAST, 4X4

HP D-off

75940-4F10JC002 $76,937 6.00 1.44 7.37 1654.4423.32FORK LIFT, ROUGH TERRAIN, 8,000 LBS @ 30' HIGH STRAIGHT MAST, 4X4

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-103


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

GENERATOR SETSG100.10 PORTABLESUBCATEGORY

WACKER CORPORATION

8GP 3800AG10WC00 $2,164 0.24 0.04 1.42 20.162.07GENERATOR SET, PORTABLE, 3.7 KW, 120/240V, 60 HZ

HP G

11GP 5600AG10WC00 $2,503 0.28 0.05 1.95 20.192.74GENERATOR SET, PORTABLE, 5.6 KW, 120/240V, 60 HZ

HP G

16GS 8.5VG10WC00 $4,666 0.52 0.08 2.84 20.344.21GENERATOR SET, PORTABLE, 8.5 KW, 120/240V, 60 HZ, WITH ELECTRIC START

HP G

18GS 9.7VG10WC00 $3,771 0.42 0.07 3.20 20.284.41GENERATOR SET, PORTABLE, 9.7 KW, 120/240V, 60 HZ, WITH ELECTRIC START

HP G


11000G10XX001 $989 0.11 0.02 0.18 10.080.42GENERATOR SET, PORTABLE, 1 KW HP G

9D4500G10XX004 $5,679 0.64 0.10 0.88 30.422.26GENERATOR SET, PORTABLE, 5 KW HP D-off

1910000G10XX002 $4,831 0.54 0.09 3.37 60.364.84GENERATOR SET, PORTABLE, 10 KW

HP G

2310000DG10XX003 $10,990 1.24 0.20 2.26 90.825.01GENERATOR SET, PORTABLE, 10 KW

HP D-off

0.20 SKID MOUNTEDSUBCATEGORY


1743304 PKG - P 304DE03

G10CA020 $27,108 2.44 0.47 17.10 371.6924.39GENERATOR SET, SKID MTD, 113 EKW, 240/480V, 60 HZ PGS PRIME

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-104


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

G10 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

3143306 PKG - 306DE39

G10CA012 $33,958 3.06 0.59 30.86 502.1241.06GENERATOR SET, SKID MTD, 210 EKW, 240 VOLT, 60 HZ PGS PRIME

HP D-off

4053406 PKG - 306DE30


HP D-off

5363406 PKG - 406DE30


HP D-off

6873412 PKG - 412DE3H


HP D-off

8173412 PKG - 412DE30


HP D-off

1,0893508 PKG - 508DE34


HP D-off

1,4433512 PKG - 512DE1F


HP D-off

2,3043516 PKG - 516DE35


HP D-off


3625GG10XX005 $17,358 1.56 0.30 6.39 161.0810.53GENERATOR SET, SKID MTD, 25 KW HP G



10775DG10XX008 $28,210 2.54 0.49 10.51 381.7617.26GENERATOR SET, SKID MTD, 75 KW HP D-off

143100DG10XX009 $24,222 2.18 0.42 14.05 421.5120.42GENERATOR SET, SKID MTD, 100 KW

HP D-off


HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-105


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

G10 NO SPECIFIC MANUFACTURER (continued)375200DG10XX011 $39,613 3.57 0.69 36.85 602.4848.85GENERATOR SET, SKID MTD, 200

KW HP D-off


HP D-off


HP D-off


HP D-off

1,050750DG10XX015 $139,285 12.54 2.44 103.18 2158.71142.37GENERATOR SET, SKID MTD, 750 KW

HP D-off

1,4251000DG10XX016 $196,843 17.72 3.45 140.03 25012.31194.75GENERATOR SET, SKID MTD, 1,000 KW

HP D-off

GRADERS, MOTORG150.00 GRADERS, MOTORSUBCATEGORY


125120-HG15CA001 $220,494 11.28 4.17 11.49 2999.8143.64GRADER, MOTOR, ARTICULATED, 6X4, 12' BLADE W/17 TEETH SCARIFIERS

HP D-off


HP D-off


HP D-off

165140-HG15CA004 $276,637 14.17 5.24 15.17 34712.3355.53GRADER, MOTOR, ARTICULATED, 6X4, 12' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

185143-HG15CA008 $320,471 16.44 6.07 17.01 36414.2963.68GRADER, MOTOR, ARTICULATED, 6X6, AWD, 12' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-106


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

G15 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

185160-HG15CA009 $299,630 15.36 5.67 17.01 37213.3560.73GRADER, MOTOR, ARTICULATED, 6X4, 14' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

200163-HG15CA010 $346,646 17.79 6.56 18.39 38815.4668.79GRADER, MOTOR, ARTICULATED, 6X6, AWD, 14' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

21514-HG15CA005 $379,859 19.18 7.19 19.76 44816.7876.82GRADER, MOTOR, ARTICULATED, 6X4, 14' BLADE W/7 SHANK RIPPER

HP D-off

27516-HG15CA006 $546,889 27.71 10.35 25.28 59424.21106.96GRADER, MOTOR, ARTICULATED, 6X4, 16' BLADE W/7 SHANK RIPPER

HP D-off

DEERE & COMPANY

151670CHG15JD008 $240,359 12.14 4.55 13.88 34310.6250.22GRADER, MOTOR, ARTICULATED, 6X4, AWD, 12' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

156672CH (HFWD)G15JD009 $276,843 14.02 5.24 14.34 35312.2555.95GRADER, MOTOR, ARTICULATED, 6X6, AWD, 12' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

185770CHG15JD010 $277,821 14.07 5.26 17.01 35312.3058.86GRADER, MOTOR, ARTICULATED, 6X4, AWD, 12' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

205772CH (HFWD)G15JD011 $313,815 15.94 5.94 18.85 36313.9166.14GRADER, MOTOR, ARTICULATED, 6X6, AWD, 12' BLADE W/5 RIPPER/SCARIFIERS

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-107


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear)H100.00 HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear)SUBCATEGORY

NPK CONSTRUCTION EQUIPMENT

E-200H10NP001 $7,296 0.97 0.14 0.00 20.633.11HAMMERS, HYDRAULIC, 150 FT-LBS, IMPACT FREQUENCY 700 BPM (ADD 150-250 HP HYDRAULIC EXCAVATOR H25)(ADD COST FOR POINT WEAR)

E-201H10NP002 $8,103 1.08 0.16 0.00 20.703.41HAMMERS, HYDRAULIC, 200 FT-LBS, IMPACT FREQUENCY 750 BPM (ADD 60-75 HP HYDRAULIC EXCAVATOR H25 OR L50)(ADD COST FOR POINT WEAR)

E-202H10NP003 $12,130 1.62 0.24 0.00 41.055.10HAMMERS, HYDRAULIC, 350 FT-LBS, IMPACT FREQUENCY 800 BPM (ADD 60-75HP HYDRAULIC EXCAVATOR H25 OR L50)(ADD COST FOR POINT WEAR)



E-205H10NP006 $27,803 3.71 0.55 0.00 112.4110.98HAMMERS, HYDRAULIC, 1,300 FT-LBS, IMPACT FREQUENCY 750 BPM (ADD 95-125 HP HYDRAULIC EXCAVATOR H25)(ADD COST FOR POINT WEAR)

EP 1110-1-8, Vol. 130 Nov 09

2-108


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

H10 NPK CONSTRUCTION EQUIPMENT (continued)



E-210AH10NP015 $65,601 8.75 1.30 0.00 345.6824.79HAMMERS, HYDRAULIC, 3,000 FT-LBS, IMPACT FREQUENCY 670 BPM (ADD 20-28 TON HYDRAULIC EXCAVATOR H25)(ADD COST FOR POINT WEAR)

E-216H10NP016 $90,420 12.06 1.79 0.00 567.8233.70HAMMERS, HYDRAULIC, 5,500 FT-LBS, IMPACT FREQUENCY 500 BPM (ADD 28-43 TON HYDRAULIC EXCAVATOR H25)(ADD COST FOR POINT WEAR)

E-220H10NP017 $118,062 15.74 2.34 0.00 6810.2143.61HAMMERS, HYDRAULIC, 8,000 FT-LBS, IMPACT FREQUENCY 430 BPM (ADD 33-50 TON HYDRAULIC EXCAVATOR H25)(ADD COST FOR POINT WEAR)

E-260AH10NP018 $274,063 36.54 5.43 0.00 17023.7099.59HAMMERS, HYDRAULIC, 20,000 FT-LBS, IMPACT FREQUENCY 330 BPM (ADD 80-130 TON HYDRAULIC EXCAVATOR H25)(ADD COST FOR POINT WEAR)

EP 1110-1-8, Vol. 130 Nov 09

2-109


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

HAZARDOUS/TOXIC WASTE EQUIPMENTH130.11 COMPACTORS (Compression force) 0 THRU 50 TONSSUBCATEGORY

CONSOLIDATED BALING MACHINE COMPANY, INC

5DOS RAW WIH13CB001 $23,915 2.03 0.43 0.46 251.455.80HAZARDOUS/TOXIC WASTE EQIPMENT, COMPACTOR, RADIOLOGICAL WASTE, 12.5 TON, LOW LEVEL

HP E

10DOS RAW W2H13CB002 $25,856 2.20 0.47 0.92 251.576.94HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, RADIOLOGICAL WASTE, 20 TON, LOW LEVEL

HP E

WASTE CONTROL SYSTEMS, INC.

58041CCH13CO002 $11,298 0.96 0.21 0.46 1670.693.27HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 37 TON HAZARD WASTE IN-DRUM , EXPLOSION PROOF

HP E

ENVIRO-PAK

54000HMH13EP001 $23,597 2.01 0.43 0.46 321.445.75HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 30 TON HAZARDOUS WASTE, HAZ-MAT STORAGE CONTAINER 40"X40"X40"

HP E

TEEMARK CORPORATION

5DPC60-E50H13TH001 $13,403 1.14 0.24 0.46 200.813.43HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 30 TON DRUM CRUSHER

HP E

9DPC60-D90H13TH002 $25,220 2.11 0.46 0.88 321.526.07HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 30 TON DRUM CRUSHER, TRAILER MOUNTED

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-110


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

H13 TEEMARK CORPORATION (continued)9DPC85-D90H13TH003 $28,530 2.39 0.52 0.88 471.726.74HAZARDOUS/TOXIC WASTE EQUIPMENT,

COMPACTOR, 42.5 TON DRUM CRUSHER, TRAILER MOUNTED

HP D-off

ADVANCED ENVIRONMENTAL SOLUTIONS

50CCYCH13YB001 $366,711 31.17 6.66 4.62 32022.2581.38HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 700 PSI OPERATING PRESSURE, FINAL COMPACTED SIZE 39.4" X 39.4" X 39.4"

HP E

50CCYC-HD-EH13YB002 $366,711 31.17 6.66 4.62 32022.2581.38HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 1,000 PSI OPERATING PRESSURE, FINAL COMPACTED SIZE 39.4" X 39.4" X 39.4"

HP E

50CMC-HDH13YB003 $366,711 31.17 6.66 4.62 32022.2581.38HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 1,200 PSI OPERATING PRESSURE, FINAL COMPACTED SIZE 39.4" X 39.4" X 39.4"

HP E

0.12 COMPACTORS (Compression force) OVER 50 TONSSUBCATEGORY

WASTE CONTROL SYSTEMS, INC.

38551H13CO003 $24,013 1.60 0.44 0.28 2701.244.96HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 85 TON HAZARD WASTE IN-DRUM

HP E

38564H13CO004 $35,304 2.35 0.65 0.28 2901.837.22HAZARDOUS/TOXIC WASTE EQIPMENT, COMPACTOR, 85 TON HAZARD WASTE IN-DRUM, W/HEPA FILTER

HP E

38560-EXH13CO006 $51,407 3.43 0.95 0.28 3002.679.94HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 85 TON HAZARD WASTE IN-DRUM, W/HEPA FILTER & SS PLATEN & CHAMBER

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-111


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

H13 WASTE CONTROL SYSTEMS, INC. (continued)

38560-EXLH13CO005 $61,101 4.07 1.13 0.28 3103.1711.81HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 85 TON HAZARD WASTE IN-DRUM, EXPLOSION PROOF, W/LIQUID REMOVAL SYSTEM

HP E

ENVIRO-PAK

89600HMH13EP002 $38,718 2.58 0.72 0.69 1002.018.28HAZARDOUS/TOXIC WASTE EQUIPMENT, COMPACTOR, 250 TON HAZARDOUS WASTE, B-25 METAL STORAGE CONTAINER 4'X4'X6'

HP E

0.21 FILTER PRESSES, STATIONARYSUBCATEGORY

KOMLINE-SANDERSON ENGINEERING CO.

100L/S 1200/25H13AY015 $62,731 5.02 1.18 0.00 1123.6913.17HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 25 CF MEMBRANE, 1,200 MM SQ (ADD 100 CFM COMPRESSOR)

CFM A

100K/F 1200/25H13AY016 $40,677 3.25 0.76 0.00 1082.398.53HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 25 CF CONVENTIONAL, 1,200 MM SQ (ADD 100 CFM COMPRESSOR)

CFM A


CFM A


CFM A

EP 1110-1-8, Vol. 130 Nov 09

2-112


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

H13 KOMLINE-SANDERSON ENGINEERING CO. (continued)


CFM A


CFM A


CFM A


CFM A


CFM A


CFM A


CFM A

EP 1110-1-8, Vol. 130 Nov 09

2-113


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)



CFM A

1H13AY019 $12,955 1.04 0.24 0.09 50.763.11HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, FILTER PRESS PLATE SHIFTING UNIT, 1,200 MM SQ, MECHANIZED

HP E

1SLC-500H13AY020 $16,782 1.34 0.31 0.09 20.983.90HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, PLC CONTROL PANEL - PLATE SHIFTING, COMPUTER AUTOMATED

HP E

USFILTER PERRIN PRODUCTS

3PLC 25-1000H13PR001 $99,194 7.94 1.86 0.28 1255.8321.27HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 25 CF STANDARD FILTER PRESS, 1,000 MM SQ

HP E


HP E


HP E

10PLC 270-1500H13PR007 $285,144 22.81 5.35 0.92 1,10016.7661.31HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 270 CF MAXI FILTER PRESS, 1,500 MM SQ

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-114


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

H13 USFILTER PERRIN PRODUCTS (continued)2BPR 1200-15HH13PR022 $205,101 16.41 3.85 0.18 19112.0643.34HAZARDOUS/TOXIC WASTE EQUIPMENT,

FILTER PRESS, STATIONARY, 47" WIDE FILTER BELT PRESS, 2 HP

HP E

3BPR 1600-15HH13PR023 $234,601 18.77 4.40 0.28 25813.7949.68HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 63" WIDE FILTER BELT PRESS, 3 HP

HP E

3BPR 2000-15HH13PR024 $260,021 20.80 4.88 0.28 31915.2855.02HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 78.75" WIDE FILTER BELT PRESS, 3 HP

HP E

3BPR 2500-15HH13PR025 $313,451 25.08 5.88 0.28 51518.4266.23HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 98.5" WIDE FILTER BELT PRESS, 3 HP

HP E

4BPR 3000-15HH13PR026 $382,091 30.57 7.17 0.37 59422.4680.78HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, STATIONARY, 118" WIDE FILTER BELT PRESS, 4 HP

HP E

0.22 FILTER PRESSES, MOBILESUBCATEGORY

KOMLINE-SANDERSON ENGINEERING CO.

100L/S 1200/25MH13AY031 $78,063 6.46 1.42 0.00 1124.6515.96HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 25 CF MEMBRANE, 1,200 MM SQ, TRAILER MOUNTED (ADD 100 CFM COMPRESSOR)

CFM A

100K/F 1200/25MH13AY032 $52,147 4.25 0.95 0.00 1093.0810.72HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 25 CF CONVENTIONAL, 1,200 MM SQ, TRAILER MOUNTED (ADD 100 CFM COMPRESSOR)

CFM A

EP 1110-1-8, Vol. 130 Nov 09

2-115


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)



CFM A


CFM A


CFM A


CFM A


CFM A


CFM A

EP 1110-1-8, Vol. 130 Nov 09

2-116


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT



CFM A


CFM A


CFM A

100K/F 1200/150MH13AY022 $116,126 9.69 2.11 0.00 2446.9623.64HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 150 CF CONVENTIONAL, 1200 MM SQ, TRAILER MOUNTED (ADD 100 CFM COMPRESSOR)

CFM A

KOCH-WATER

13BFP-0500H13KP001 $81,914 6.91 1.49 1.15 404.9518.42HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, FILTER BELT PRESS, 20" (0.5M) WIDE, 0.6 - 2.0 TONS/HR, TRAILER MOUNTED (STAND ALONE UNIT, INCLUDES POLYMER FEED PUMP, BOOSTER PUMP, SLUDGE PUMP, AND DISCHARGE CONVEYOR)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-117


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

H13 KOCH-WATER (continued)16BFP-1000H13KP002 $92,882 7.85 1.69 1.43 485.6221.09HAZARDOUS/TOXIC WASTE EQUIPMENT,

FILTER PRESS, MOBILE, FILTER BELT PRESS, 39" (1.0M) WIDE, 3.0 - 6.5 TONS/HR, TRAILER MOUNTED (STAND ALONE UNIT, INCLUDES POLYMER FEED PUMP, BOOSTER PUMP, SLUDGE PUMP, AND DISCHARGE CONVEYOR)

HP E


HP E


HP E

USFILTER PERRIN PRODUCTS

3PLC 25-1000MH13PR002 $278,897 23.53 5.06 0.28 14516.8358.44HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 25 CF STANDARD FILTER PRESS, 1,000 MM SQ, TRAILER MOUNTED (COMPLETE)

HP E

5180-1500MH13PR006 $246,288 20.76 4.47 0.46 70514.8552.14HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 180 CF STANDARD FILTER PRESS,1,500 MM SQ, TRAILER MOUNTED

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-118


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

H13 USFILTER PERRIN PRODUCTS (continued)2BPR 1200-15H-MH13PR011 $385,222 32.57 6.99 0.18 23523.2879.75HAZARDOUS/TOXIC WASTE EQUIPMENT,

FILTER PRESS, MOBILE, 47" FILTER BELT PRESS, TRAILER MOUNTED (STAND ALONE UNIT, ADD APPURTENANCES SUCH AS FEED PUMPS, POLYMER SYSTEM, WASH WATER BOOSTER PUMP, CONVEYOR ETC.)

HP E

3BPR 1600-15H-MH13PR012 $414,029 35.01 7.52 0.28 30225.0385.72HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 63" FILTER BELT PRESS, TRAILER MOUNTED (STAND ALONE UNIT, ADD APPURTENANCES SUCH AS FEED PUMPS, POLYMER SYSTEM, WASH WATER BOOSTER PUMP, CONVEYOR ETC.)

HP E

5BPR 2000-15H-MH13PR013 $439,375 37.17 7.98 0.46 31926.5791.12HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 78.75" FILTER BELT PRESS, TRAILER MOUNTED (STAND ALONE UNIT, ADD APPURTENANCES SUCH AS FEED PUMPS, POLYMER SYSTEM, WASH WATER BOOSTER PUMP, CONVEYOR ETC.)

HP E

8BPR 2500-15H-MH13PR014 $492,805 41.71 8.95 0.74 51529.81102.35HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, 98.5" FILTER BELT PRESS, TRAILER MOUNTED (STAND ALONE UNIT, ADD APPURTENANCES SUCH AS FEED PUMPS, POLYMER SYSTEM, WASH WATER BOOSTER PUMP, CONVEYOR ETC.)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-119


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

H13 USFILTER PERRIN PRODUCTS (continued)8BPR 3000-15H-MH13PR015 $561,446 47.55 10.19 0.74 59433.97116.21HAZARDOUS/TOXIC WASTE EQUIPMENT,

FILTER PRESS, MOBILE, 118" FILTER BELT PRESS, TRAILER MOUNTED (STAND ALONE UNIT, ADD APPURTENANCES SUCH AS FEED PUMPS, POLYMER SYSTEM, WASH WATER BOOSTER PUMP, CONVEYOR ETC.)

HP E

SOMAT WASTE REDUCTION TECHNOLOGY

31PB-6DH13S5001 $55,521 4.72 1.01 0.28 143.3711.66HAZARDOUS/TOXIC WASTE EQUIPMENT, FILTER PRESS, MOBILE, PUSHER SCREW PRESS, 6-15 GPM CAPACITY, TRAILER MOUNTED

HP E


HP E


HP E

0.30 CENTRIFUGESSUBCATEGORY

BOCK ENGINEERED PRODUCTS, INC.

3GP 35H13BC013 $15,203 3.04 0.32 0.28 91.847.09HAZARDOUS/TOXIC WASTE EQUIPMENT, CENTRIFUGE, FIXED SPEED, TIMER, 35 LB DRY WT.

HP E

3305 TXH13BC010 $16,117 3.22 0.34 0.28 61.957.49HAZARDOUS/TOXIC WASTE EQUIPMENT, CENTRIFUGE, FIXED SPEED, TIMER, 35 LB DRY WT.

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-120


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

H13 BOCK ENGINEERED PRODUCTS, INC. (continued)


HP E

3605 TXH13BC006 $21,060 4.21 0.44 0.28 92.559.65HAZARDOUS/TOXIC WASTE EQUIPMENT, CENTRIFUGE, FIXED SPEED, TIMER, 60 LB DRY WT.

HP E


HP E


HP E

3355H13BC009 $27,383 5.48 0.58 0.28 63.3212.42HAZARDOUS/TOXIC WASTE EQUIPMENT, CENTRIFUGE, FIXED SPEED, MANUAL CONTROL, EXPLOSION PROOF, 35 LB

HP E


HP E


HP E

EP 1110-1-8, Vol. 130 Nov 09

2-121


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

0.40 SHREDDERSSUBCATEGORY

GRANUTE-SATURN SYSTEMS(MAC CORPORATION)

15052-32HTH13MN001 $345,975 29.08 6.28 13.85 20020.8298.30HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 32" X 52" OPENING, TRAILER MTD, W/DIESEL GENERATOR SET/ BELT-TYPE INFEED & DISCHARGE CONVEYORS

HP E

20062-40HTH13MN002 $404,997 34.00 7.35 18.46 30024.35119.00HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 38" X 62" OPENING, TRAILER MTD, W/DIESEL GENERATOR SET, HOOK-TYPE INFEED FOR TIRES, & DISCHARGE CONVEYOR

HP E

20062-40HTH13MN003 $458,883 38.58 8.33 18.46 30027.62131.55HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 38" X 62" OPENING, TRAILER MTD, W/DIESEL GENERATOR SET, CRANE GRAPPLE & DISCHARGE CONVEYOR SYSTEM

HP E

30072-46HTH13MN004 $523,565 44.08 9.50 27.69 40031.54160.56HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 45" X 72" OPENING , TRAILER MTD, W/DIESEL GENERATOR SET, CRANE GRAPPLE & DISCHARGE CONVEYOR SYSTEM

HP E

SHRED-TECH LIMITED

20ST-25EH13SH001 $53,995 4.59 0.98 1.85 203.2814.41HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 29" X 42" OPENING, TRAILER MTD. (ADD COST FOR CONVEYOR SYSTEM, POWER SUPPLY, AND TRAILER)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-122


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

H13 SHRED-TECH LIMITED (continued)20ST-25ELH13SH002 $50,650 4.31 0.92 1.85 233.0813.70HAZARDOUS/TOXIC WASTE EQUIPMENT,

SHREDDER, 29" X 46" OPENING, TRAILER MTD. (ADD COST FOR CONVEYOR SYSTEM, POWER SUPPLY, AND TRAILER)

HP E

40ST-50H13SH003 $87,189 7.41 1.58 3.69 455.2924.34HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 40" X 55" OPENING, TRAILER MTD. (ADD COST FOR CONVEYOR SYSTEM, POWER SUPPLY, AND TRAILER)

HP E

40ST-50LH13SH004 $90,989 7.73 1.65 3.69 505.5225.15HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 40" X 65" OPENING, TRAILER MTD. (ADD COST FOR CONVEYOR SYSTEM, POWER SUPPLY, AND TRAILER)

HP E


HP E


HP E

600ST-500LH13SH007 $609,516 51.81 11.06 55.38 44036.97215.56HAZARDOUS/TOXIC WASTE EQUIPMENT, SHREDDER, 66" X 115" OPENING, TRAILER MTD. (ADD COST FOR CONVEYOR SYSTEM, POWER SUPPLY, AND TRAILER)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-123


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

0.71 WASTE HANDLING EQUIPMENT, DRUM HANDLINGSUBCATEGORY

BASCO

10VELT 55/35H13BB001 $20,596 4.38 0.43 0.92 112.6213.32HAZARDOUS/TOXIC WASTE EQUIPMENT, WASTE HANDLING EQUIPMENT, DRUM HANDLING, DRUM FILLER, 55 GAL TOP FILL

HP E

152BH13BB002 $18,354 3.90 0.38 1.38 192.3313.06HAZARDOUS/TOXIC WASTE EQUIPMENT, WASTE HANDLING EQUIPMENT, DRUM CLEANER, 12 DRUM/HR CAP INTERIOR

HP E

HOISTS & AIR WINCHESH200.00 HOISTS & AIR WINCHESSUBCATEGORY

INGERSOLL RAND MATERIAL HANDLING

700FA2.5H20BE002 $38,417 3.41 0.73 0.00 102.448.55AIR WINCH, MANUAL BRAKE, 24" DRUM, 5,000 LBS CAP, 145 FPM (ADD 700 CFM COMPRESSOR)

CFM A

700FA5H20BE003 $47,606 4.23 0.90 0.00 193.0210.65AIR WINCH, MANUAL BRAKE, 24" DRUM, 10,000 LBS CAP, 65 FPM (ADD 700 CFM COMPRESSOR)

CFM A

800FA10H20BE004 $52,369 4.66 0.99 0.00 353.3211.79AIR WINCH, AUTOMATIC BRAKE, 24" DRUM, 22,000 LBS CAP, 30 FPM (ADD 800 CFM COMPRESSOR)

CFM A

EP 1110-1-8, Vol. 130 Nov 09

2-124


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

HYDRAULIC EXCAVATORS, CRAWLER MOUNTEDH250.10 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS)SUBCATEGORY


18301.8H25CA034 $37,288 3.50 0.74 1.77 372.4910.16HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 3,800 LBS, 0.04 CY BUCKET, 7.50' MAX DIGGING DEPTH

HP D-off

30303 CRH25CA035 $43,623 4.09 0.86 2.95 762.9112.90HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 7,500 LBS, 0.11 CY BUCKET, 9.08' MAX DIGGING DEPTH

HP D-off

47305 CRH25CA036 $70,110 6.57 1.39 4.62 1154.6820.60HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 10,800 LBS, 0.17 CY BUCKET, 11.08' MAX DIGGING DEPTH

HP D-off

Komatsu America International Company

20PC20MR-2H25KM018 $47,555 4.46 0.94 1.97 513.1712.62HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 4,800 LBS, 0.05 CY BUCKET, 8'11" MAX DIGGING DEPTH

HP D-off

39PC40MR-2H25KM021 $64,014 6.00 1.26 3.83 1064.2618.35HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 10,000 LBS, 0.18 CY BUCKET, 12'9" MAX DIGGING DEPTH

HP D-off

40PC58UU-3H25KM022 $81,806 7.67 1.62 3.93 1155.4622.34HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 11,400 LBS, 0.29 CY BUCKET, 13'1" MAX DIGGING DEPTH

HP D-off

54PC78US-6H25KM023 $100,858 9.46 1.99 5.31 1596.7228.08HYDRAULIC EXCAVATOR, CRAWLER, 6,200 LBS, 0.37 CY BUCKET, 12'4" MAX DIGGING DEPTH

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-125


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

MELROE COMPANY/BOBCAT

13323H25ME001 $29,152 2.73 0.58 1.31 371.957.85HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 3,600 LBS, 0.04 CY BUCKET, 7'6" MAX DIGGING DEPTH

HP D-off

40331H25ME002 $41,809 3.92 0.83 3.93 722.7913.66HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 7,200 LBS, 0.10 CY BUCKET, 10'2" MAX DIGGING DEPTH

HP D-off

48337H25ME003 $58,108 5.45 1.15 4.72 1103.8818.12HYDRAULIC EXCAVATOR, CRAWLER-RUBBER TRACK, 11,000 LBS, 0.18 CY BUCKET, 12' MAX DIGGING DEPTH

HP D-off

0.11 OVER 12,500 LBS THRU 40,000 LBSSUBCATEGORY


54307DH25CA038 $100,912 8.90 1.98 5.31 1596.4326.90HYDRAULIC EXCAVATOR, CRAWLER, 14,310 LBS, 0.48 CY BUCKET, 15.25' MAX DIGGING DEPTH

HP D-off

79311-CUH25CA020 $129,180 11.40 2.54 7.76 2588.2435.57HYDRAULIC EXCAVATOR, CRAWLER, 24,640 LBS, 0.60 CY BUCKET, 16.50' MAX DIGGING DEPTH

HP D-off

84312-D LH25CA021 $129,942 11.47 2.55 8.25 2888.2936.29HYDRAULIC EXCAVATOR, CRAWLER, 26,900 LBS, 0.68 CY BUCKET, 18.16' MAX DIGGING DEPTH

HP D-off


5470SRH25KC017 $110,655 9.76 2.17 5.31 1687.0528.90HYDRAULIC EXCAVATOR, CRAWLER, 16,400 LBS, 0.33 CY BUCKET, 14.75' MAX DIGGING DEPTH

HP D-off

94135SR LCH25KC016 $157,003 13.85 3.08 9.24 31910.0142.99HYDRAULIC EXCAVATOR, CRAWLER, 30,870 LBS, 0.60 CY BUCKET, 19.58' MAX DIGGING DEPTH

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-126


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT


86PC128UU-2H25KM027 $195,907 17.29 3.85 8.45 29512.5050.06HYDRAULIC EXCAVATOR, CRAWLER, 12,200 LBS, 0.58 CY BUCKET, 16' 0" MAX DIGGING DEPTH

HP D-off

89PC 120-6H25KM001 $138,616 12.23 2.72 8.75 2658.8438.65HYDRAULIC EXCAVATOR, CRAWLER, 26,950 LBS, 0.75 CY BUCKET, 18.08' MAX DIGGING DEPTH

HP D-off

110PC 160LC-7H25KM003 $214,168 18.90 4.21 10.81 39513.6656.56HYDRAULIC EXCAVATOR, CRAWLER, 39,400 LBS, 1.12 CY BUCKET, 19.58' MAX DIGGING DEPTH

HP D-off


89130 LXH25LI003 $143,692 12.68 2.82 8.75 2719.1639.69HYDRAULIC EXCAVATOR, CRAWLER, 27,100 LBS, 0.50 CY BUCKET, 18' 2" MAX DIGGING DEPTH

HP D-off

101160 LXH25LI005 $168,008 14.82 3.30 9.93 36210.7146.06HYDRAULIC EXCAVATOR, CRAWLER, 35,275 LBS, 0.66 CY BUCKET, 20' 1" MAX DIGGING DEPTH

HP D-off



125319CLH25CA040 $139,742 8.73 2.68 12.28 4057.0536.74HYDRAULIC EXCAVATOR, CRAWLER, 40,600 LBS, 1.00 CY BUCKET, 22.50' MAX DIGGING DEPTH

HP D-off

128320DH25CA022 $209,092 13.07 4.01 12.58 44410.5548.23HYDRAULIC EXCAVATOR, CRAWLER, 43,800 LBS, 1.50 CY BUCKET, 21.75' MAX DIGGING DEPTH

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-127


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

H25 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

128320DLH25CA023 $302,102 18.88 5.79 12.58 53615.2363.14HYDRAULIC EXCAVATOR, CRAWLER, 49,000 LBS, 0.80 CY BUCKET, 39.0' MAX DIGGING DEPTH, LONG REACH BOOM

HP D-off


143SK210 LCH25KC019 $244,475 15.28 4.68 14.05 48012.3255.60HYDRAULIC EXCAVATOR, CRAWLER, 48,000 LBS, 1.13 CY BUCKET, 22.00' MAX DIGGING DEPTH

HP D-off

143SK210 LCH25KC020 $268,205 16.76 5.14 14.05 53413.5259.41HYDRAULIC EXCAVATOR, CRAWLER, 53,400 LBS, 0.63 CY BUCKET, 39' MAX DIGGING DEPTH, LONG REACH BOOM

HP D-off


HP D-off

176SK250 LCH25KC022 $321,370 20.09 6.16 17.30 59116.2171.75HYDRAULIC EXCAVATOR, CRAWLER, 59,100 LBS, 0.50 CY BUCKET, 23' MAX DIGGING DEPTH, LONG REACH BOOM

HP D-off


HP D-off



306SK400 LCH25KC024 $509,842 23.90 9.61 30.07 1,01921.56102.82HYDRAULIC EXCAVATOR, CRAWLER, 101,900 LBS 3.06 CY BUCKET, 25.58' MAX DIGGING DEPTH

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-128


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

H25 KOBELCO AMERICA INC. (continued)315SK480LCH25KC026 $534,176 25.04 10.06 30.96 1,08022.58107.15HYDRAULIC EXCAVATOR, CRAWLER,

108,000 LBS, 2.25 CY BUCKET, 25.58' MAX DIGGING DEPTH

HP D-off


384PC 600 LC-7H25KM015 $915,400 42.91 17.25 37.74 1,33238.71167.52HYDRAULIC EXCAVATOR, CRAWLER, 133,160 LBS, 4.25 CY BUCKET, 27.83' MAX DIGGING DEPTH

HP D-off

0.14 OVER 160,000 LBSSUBCATEGORY


454PC 750LC-7H25KM009 $1,097,081 43.31 20.51 44.61 1,75042.17186.04HYDRAULIC EXCAVATOR, CRAWLER, 171,070 LBS, 4.05 CY BUCKET, 27.66' MAX DIGGING DEPTH

HP D-off

908PC1800-6H25KM033 $2,198,097 86.77 41.10 89.23 3,96884.49372.60HYDRAULIC EXCAVATOR, CRAWLER, 396,800 LBS, 15.70 CY BUCKET, 30'5" MAX DIGGING DEPTH

HP D-off

0.21 ATTACHMENTS, MOBILE SHEARSSUBCATEGORY


S305H25CA055 $19,424 2.75 0.37 0.00 151.757.12HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, SCRAP, 9.4" JAW OPENING (ADD 10,000 LB HYDRAULIC EXCAVATOR)

S320BH25CA057 $81,401 11.53 1.57 0.00 577.3428.97HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, SCRAP, 15.4" JAW OPENING (ADD 20,000 LB HYDRAULIC EXCAVATOR)

EP 1110-1-8, Vol. 130 Nov 09

2-129


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)


S230H25CA052 $102,241 14.48 1.97 0.00 849.2136.88HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, SCRAP, 22.0" JAW OPENING (ADD 35,000 LB HYDARULIC EXCAVATOR)




LABOUNTY MANUFACTURING,

MSD 7H25LU001 $26,018 3.69 0.50 0.00 102.359.41HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, 10" JAW OPENING (ADD 10,000 LB HYDRAULIC EXCAVATOR)

MSD 7RH25LU002 $29,324 4.15 0.56 0.00 112.6410.64HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, 10" JAW OPENING (ADD 14,000 LB HYDRAULIC EXCAVATOR)

MSD 15H25LU003 $45,274 6.41 0.87 0.00 304.0816.46HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, 18" JAW OPENING (ADD 20,000 LB HYDRAULIC EXCAVATOR)

MSD 15RH25LU004 $52,633 7.46 1.01 0.00 354.7419.12HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, 18" JAW OPENING (ADD 25,000 LB HYDRAULIC EXCAVATOR)

EP 1110-1-8, Vol. 130 Nov 09

2-130


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

H25 LABOUNTY MANUFACTURING, (continued)MSD 30 - III SVH25LU005 $65,985 9.35 1.27 0.00 505.9523.94HYDRAULIC EXCAVATOR, ATTACHMENT,

MOBILE SHEARS, 22" JAW OPENING (ADD 25,000 LB HYDRAULIC EXCAVATOR)

MSD 30R - III SVH25LU006 $92,461 13.10 1.78 0.00 678.3333.50HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, 22" JAW OPENING (ADD 35,000 LB HYDRAULIC EXCAVATOR)

MSD 40-III SVH25LU007 $78,864 11.17 1.52 0.00 707.1128.69HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, 27" JAW OPENING (ADD 40,000 LB HYDRAULIC EXCAVATOR)

MSD 40R-III SVH25LU008 $103,154 14.61 1.98 0.00 909.2937.29HYDRAULIC EXCAVATOR, ATTACHMENT, MOBILE SHEARS, 27" JAW OPENING (ADD 45,000 LB HYDRAULIC EXCAVATOR)







EP 1110-1-8, Vol. 130 Nov 09

2-131


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

0.22 ATTACHMENTS, MATERIAL HANDLINGSUBCATEGORY

BALDERSON, INC.

H25BS001 $5,163 0.69 0.10 0.00 100.451.64HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, 0.50 CY BUCKET, W/TIPS (ADD 25,000-50,000 LB HYDRAULIC EXCAVATOR)






TW 100H25LU023 $35,849 4.78 0.71 0.00 163.1011.64HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, GRAPPLE, 1.25CY, 4-TINE/ 5-TINE (ADD 25,000 LB HYDRAULIC EXCAVATOR)

EP 1110-1-8, Vol. 130 Nov 09

2-132


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

H25 LABOUNTY MANUFACTURING, (continued)TW 110H25LU024 $17,885 2.38 0.35 0.00 281.545.97HYDRAULIC EXCAVATOR, ATTACHMENT,

MATERIAL HANDLING, GRAPPLE, 3.50CY, 4-TINE/ 5-TINE (ADD 35,000 LB HYDRAULIC EXCAVATOR)

120 TRH25LU025 $21,922 2.92 0.43 0.00 351.897.36HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, GRAPPLE, 3.50CY, 4-TINE/ 5-TINE (ADD 45,000 LB HYDRAULIC EXCAVATOR)

140 TWH25LU026 $24,946 3.33 0.49 0.00 482.168.42HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, GRAPPLE, 5.50CY, 4-TINE/ 5-TINE (ADD 60,000 LB HYDRAULIC EXCAVATOR)

160 TRH25LU027 $27,917 3.72 0.55 0.00 582.419.46HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, GRAPPLE, 6.50CY, 4-TINE/ 5-TINE (ADD 75,000 LB HYDRAULIC EXCAVATOR)

TW 170H25LU028 $46,099 6.15 0.91 0.00 783.9915.34HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, GRAPPLE, 9.00CY, 4-TINE/ 5-TINE (ADD 100,000 LB HYDRAULIC EXCAVATOR)

RDG 60H25LU034 $67,211 8.96 1.33 0.00 355.8122.15HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, ROTATING GRAPPLE, 1.75 CY (ADD 38,000-70,000 LB HYDRAULIC EXCAVATOR)

RDG 90H25LU035 $80,494 10.73 1.60 0.00 696.9726.47HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, ROTATING GRAPPLE, 1.25 CY (ADD 70,000-140,000 LB HYDRAULIC EXCAVATOR)

EP 1110-1-8, Vol. 130 Nov 09

2-133


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

H25 LABOUNTY MANUFACTURING, (continued)RDG 120H25LU036 $92,705 12.36 1.84 0.00 1008.0230.45HYDRAULIC EXCAVATOR, ATTACHMENT,

MATERIAL HANDLING, ROTATING GRAPPLE, 2.00 CY (ADD 120,000-160,000 LB HYDRAULIC EXCAVATOR)

WAIN-ROY, INC.

H25WN001 $7,343 0.98 0.15 0.00 160.642.34HYDRAULIC EXCAVATOR, ATTACHMENT, MATERIAL HANDLING, BUCKET, 36" CONCRETE/PAVEMENT REMOVAL (ADD 75,000 LB HYDRAULIC EXCAVATOR)

0.23 ATTACHMENTS, CONCRETE PULVERIZERSSUBCATEGORY


CR3H25CA058 $21,642 3.07 0.42 0.00 61.968.44HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, CRUSHER, 16.0" JAW OPENING (ADD 40,000 LB MIN HYDRAULIC EXCAVATOR)

P16H25CA059 $79,021 11.19 1.52 0.00 537.1229.56HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, 30.0" JAW OPENING (ADD 40,000 LB MIN HYDRAULIC EXCAVATOR)



EP 1110-1-8, Vol. 130 Nov 09

2-134


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT





KENT DEMOLITION TOOLS

KF12 TLBH25KN001 $28,616 4.05 0.55 0.00 192.5810.99HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE BREAKER, 2,000 FT-LB, W/4.25'' DIA. POINT (ADD 16,000-24,000 LB HYDRAULIC EXCAVATOR)

KF19 QTH25KN002 $39,688 5.62 0.76 0.00 313.5715.04HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE BREAKER, 3,000 FT-LB, W/4.75'' DIA. POINT (ADD 26,000-36,000 LB HYDRAULIC EXCAVATOR)



EP 1110-1-8, Vol. 130 Nov 09

2-135


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

H25 KENT DEMOLITION TOOLS (continued)KF70 QTH25KN006 $112,296 15.91 2.16 0.00 10310.1242.17HYDRAULIC EXCAVATOR, ATTACHMENT,

CONCRETE BREAKER, 10,000 FT-LB, W/7.09 '' DIA. POINT (ADD 80,000 LB HYDRAULIC EXCAVATOR)


CP 40 CH25LU046 $33,481 4.74 0.64 0.00 293.0112.77HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, 30" JAW OPENING (ADD 40,000 LB HYDRAULIC EXCAVATOR)

CP 60 SH25LU047 $38,501 5.45 0.74 0.00 303.4714.71HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, 36" JAW OPENING (ADD 60,000 LB HYDRAULIC EXCAVATOR)




UP 45 SVH25LU040 $140,682 19.93 2.71 0.00 10512.6852.32HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, CRACKING JAWS, 45" JAW OPENING (ADD 55,000 LB HYDRAULIC EXCAVATOR)

EP 1110-1-8, Vol. 130 Nov 09

2-136


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

H25 LABOUNTY MANUFACTURING, (continued)UP 75 SVH25LU041 $172,560 24.45 3.32 0.00 12715.5564.01HYDRAULIC EXCAVATOR, ATTACHMENT,

CONCRETE PULVERIZER, CRACKING JAWS, 49" JAW OPENING (ADD 80,000 LB HYDRAULIC EXCAVATOR)

UP 90H25LU042 $208,156 29.49 4.01 0.00 17118.7677.81HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, CRACKING JAWS, 62" JAW OPENING (ADD 75,000 LB HYDRAULIC EXCAVATOR)

UP 45 SVH25LU053 $148,047 20.97 2.85 0.00 10513.3455.02HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, 36" JAW OPENING (ADD 55,000 LB HYDRAULIC EXCAVATOR)

UP 75 SVH25LU054 $182,269 25.82 3.51 0.00 12616.4267.57HYDRAULIC EXCAVATOR, ATTACHMENT, CONCRETE PULVERIZER, 40" JAW OPENING (ADD 80,000 LB HYDRAULIC EXCAVATOR)

0.24 ATTACHMENTS, COMPACTORSSUBCATEGORY

ALLIED CONSTRUCTION PRODUCTS

4700 W/SWIVELH25AU001 $7,417 1.05 0.14 0.00 40.672.72HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 18" X 12" PLATE, 3,000 LBS FORCE (ADD 15,000-20,000 LB HYDRAULIC EXCAVATOR)

8700C W/SWIVEL

H25AU002 $8,541 1.21 0.16 0.00 90.773.13HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 34" X 24" PLATE, 6,400 LBS FORCE (ADD 20,000-30,000 LB HYDRAULIC EXCAVATOR)

EP 1110-1-8, Vol. 130 Nov 09

2-137


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

H25 ALLIED CONSTRUCTION PRODUCTS (continued)

9700C W/SWIVEL

H25AU003 $11,911 1.69 0.23 0.00 161.084.37HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 40" X 29" PLATE, 13,000 LBS FORCE (ADD 25,000-50,000 LB HYDRAULIC EXCAVATOR)



AMERICAN COMPACTION EQUIPMENT, INC.

DC-24BLH25AX001 $7,540 1.07 0.15 0.00 250.692.77HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 23" WIDE, SHEEPS FOOT, 3 RIMS - 38" DIA (ADD 25,000-50,000 LB HYDRAULIC EXCAVATOR)

DC-24EXH25AX003 $9,080 1.29 0.17 0.00 330.823.33HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 23" WIDE, SHEEPS FOOT, 3 RIMS - 42" DIA (ADD 50,000-75,000 LB HYDRAULIC EXCAVATOR)

DC-24EXLH25AX005 $10,262 1.45 0.20 0.00 390.933.76HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 23" WIDE, SHEEPS FOOT, 3 RIMS - 48" DIA (ADD 75,000-110,000 LB HYDRAULIC EXCAVATOR)

DC-36BLH25AX002 $8,865 1.26 0.17 0.00 330.803.25HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 35" WIDE, SHEEPS FOOT, 4 RIMS - 38" DIA (ADD 50,000-75,000 LB HYDRAULIC EXCAVATOR)

EP 1110-1-8, Vol. 130 Nov 09

2-138


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

H25 AMERICAN COMPACTION EQUIPMENT, INC. (continued)

DC-36EXH25AX004 $10,978 1.56 0.21 0.00 430.994.03HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 35" WIDE, SHEEPS FOOT, 4 RIMS - 42" DIA (ADD 50,000-75,000 LB HYDRAULIC EXCAVATOR)

DC-36EXLH25AX006 $12,661 1.79 0.24 0.00 531.144.63HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 36" WIDE, SHEEPS FOOT, 4 RIMS - 48" DIA (ADD 75,000-110,000 LB HYDRAULIC EXCAVATOR)


KHP-35 ME-SH25KN007 $5,761 0.82 0.11 0.00 40.522.26HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 12" X 26" PLATE, 3000 LB FORCE (ADD 14,000-25,000 LB HYDRAULIC EXCAVATOR)

KHP-135FT - IIH25KN009 $11,969 1.70 0.23 0.00 141.084.54HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 28" X 40" PLATE, 13500 LB FORCE (ADD 25,000-50,000 LB HYDRAULIC EXCAVATOR)

KHP-210FT - IIH25KN010 $16,514 2.34 0.32 0.00 231.496.21HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 34" X 46" PLATE, 21000 LB FORCE (ADD 40,000-75,000 LB HYDRAULIC EXCAVATOR)

WAIN-ROY, INC.

24-3 (15-22.5 TON)

H25WN002 $7,828 1.11 0.15 0.00 220.712.87HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 24'' WIDE, SHEEPSFOOT, 3 RIMS - 33" DIA (ADD 15-22.5 TON HYDRAULIC EXCAVATOR)

EP 1110-1-8, Vol. 130 Nov 09

2-139


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

H25 WAIN-ROY, INC. (continued)36-4 (15-22.5 TON)

H25WN003 $8,592 1.22 0.17 0.00 260.783.16HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 36'' WIDE, SHEEPSFOOT, 4 RIMS - 33" DIA (ADD 15-22.5 TON HYDRAULIC EXCAVATOR)

24-3 (22.5-30 TON)

H25WN004 $9,402 1.33 0.18 0.00 310.853.44HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 24'' WIDE, SHEEPSFOOT, 3 RIMS - 39" DIA (ADD 22.5-30 TON HYDRAULIC EXCAVATOR)

36-4 (22.5-30 TON)

H25WN005 $10,682 1.51 0.21 0.00 380.973.92HYDRAULIC EXCAVATOR, ATTACHMENT, COMPACTOR, 36'' WIDE, SHEEPSFOOT, 4 RIMS - 39" DIA (ADD 22.5-30 TON HYDRAULIC EXCAVATOR)

HYDRAULIC EXCAVATORS, WHEEL MOUNTEDH300.01 0 THRU 1.0 CYSUBCATEGORY


151M318DH30CA005 $198,014 18.06 3.91 13.88 39312.9454.06HYDRAULIC EXCAVATORS, WHEEL, 33,700 LBS, 1.00 CY BUCKET, 1-PIECE BOOM, 19' DIGGING DEPTH, 4X4

HP D-off

121M315DH30CA007 $167,557 15.01 3.31 11.12 35210.8245.49HYDRAULIC EXCAVATORS, WHEEL, 35,100 LBS, 0.70 CY BUCKET, 1-PIECE BOOM, 17' 7" DIGGING DEPTH, 4X4X2

HP D-off

GRADALL COMPANY

233XL4100 IIIH30GA006 $287,975 26.47 5.69 21.42 47518.9379.51D-onHYDRAULIC EXCAVATORS, WHEEL, 44,851 LBS, 0.75 CY BUCKET, TELESCOPIC BOOM, 22' 6" DIGGING DEPTH, 6X4

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-140


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

H30 GRADALL COMPANY (continued)138XL 3300 IIIH30GA007 $202,232 18.63 4.00 12.69 39313.3253.04HYDRAULIC EXCAVATORS, WHEEL, 15,270

LBS, 0.68 CY BUCKET, TELESCOPIC BOOM, 4X4X2

HP D-off

0.02 OVER 1.0 CYSUBCATEGORY

GRADALL COMPANY

163XL 5100 IIIH30GA008 $322,934 23.34 6.26 19.25 55017.9380.04230 HP D-onHYDRAULIC EXCAVATORS, WHEEL, 22,800 LBS, 1.25 CY BUCKET, TELESCOPIC BOOM, 25' 4" DIGGING DEPTH, 6X4

HP D-off


123PW170ES-6H30KM001 $242,802 17.96 4.71 11.31 37613.6953.86HYDRAULIC EXCAVATORS, WHEEL, 37,600 LBS, 1.12 CY BUCKET, 1-PIECE BOOM, 18' 8" DIGGING DEPTH, 4X4

HP D-off

HYDRAULIC SHOVELS, CRAWLER MOUNTEDH350.12 DIESEL, OVER 5.0 CYSUBCATEGORY

HITACHI CONSTRUCTION MACHINERY

641EX1200-5H35HI006 $1,350,310 67.52 24.55 62.99 2,44758.31278.33HYDRAULIC SHOVEL, CRAWLER, 8.5 CY BUCKET, FRONT SHOVEL, 17' 3" DIGGING DEPTH

HP D-off

O & K ORENSTEIN & KOPPEL INC.

607RH 40 EH35OK001 $857,927 42.90 15.60 59.65 2,20437.05197.59HYDRAULIC SHOVEL, CRAWLER, 9.20 CY BUCKET, BACKHOE, 28' 10" DIGGING DEPTH

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-141


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

H35 O & K ORENSTEIN & KOPPEL INC. (continued)

1,018RH 90 CH35OK003 $1,739,362 86.97 31.62 100.04 3,59475.11378.49HYDRAULIC SHOVEL, CRAWLER, 13.10 CY BUCKET, BACKHOE, 31' 1" DIGGING DEPTH

HP D-off

1,280RH 120 CH35OK004 $2,775,269 138.76 50.46 125.79 5,842119.84568.16HYDRAULIC SHOVEL, CRAWLER, 17.00 CY BUCKET, FRONT SHOVEL, 7' 7" DIGGING DEPTH

HP D-off

2,250RH 200H35OK005 $5,231,147 261.56 95.11 221.11 10,582225.891,054.02HYDRAULIC SHOVEL, CRAWLER, 34.00 CY BUCKET, BACKHOE, 30' 6" DIGGING DEPTH

HP D-off

LAND CLEARING EQUIPMENTL100.00 LAND CLEARING EQUIPMENTSUBCATEGORY

BALDERSON, INC.

BBL7L10BS004 $9,977 0.80 0.19 0.00 240.592.35LAND CLEARING EQUIPMENT, ROCK & ROOT RAKE, 12.0' WIDE, 9 TEETH (ADD 200 - 250 HP TRACTOR DOZER)

BRK8L10BS005 $26,420 2.11 0.50 0.00 721.565.86LAND CLEARING EQUIPMENT, ROCK & ROOT RAKE 12.5' WIDE, 9 TEETH (ADD 275 - 325 HP TRACTOR DOZER)

BMA8L10BS002 $28,907 2.31 0.54 0.00 681.706.37LAND CLEARING EQUIPMENT, MULTI-APPLICATION RAKE, 12.5' WIDE, 9 TEETH (ADD 275 - 325 HP TRACTOR DOZER)

988 DTCL10BS007 $37,163 2.97 0.70 0.00 902.198.31LAND CLEARING EQUIPMENT, LOGGING FORK, 92" TINES (ADD 400 - 450 HP FE LOADER)

EP 1110-1-8, Vol. 130 Nov 09

2-142


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

BUSH HOG

FH174L10BU009 $4,992 0.40 0.09 0.00 100.291.95LAND CLEARING EQUIPMENT, FLAIL MOWER, 62" WIDE, 0.5 - 5" HEIGHT (ADD FARM 30 - 60 HP TRACTOR)

SM-60L10BU005 $9,423 0.75 0.18 0.00 170.563.08LAND CLEARING EQUIPMENT, ROTARY CUTTER, 5' WIDE-SIDE MTD (ADD FARM 50 HP TRACTOR)

287L10BU010 $4,787 0.38 0.09 0.00 110.281.80LAND CLEARING EQUIPMENT, ROTARY CUTTER, 7' WIDE, 1.5 - 12" HEIGHT (ADD FARM 40 HP TRACTOR)

3210L10BU011 $10,298 0.82 0.19 0.00 250.603.66LAND CLEARING EQUIPMENT, ROTARY CUTTER, 10.5' WIDE, 2 - 14" HEIGHT (ADD FARM 70 HP TRACTOR)

3715L10BU012 $21,121 1.69 0.40 0.00 501.256.44LAND CLEARING EQUIPMENT, ROTARY CUTTER, 15' WIDE, 2 - 14" HEIGHT (ADD FARM 80 HP TRACTOR)

2720L10BU013 $21,899 1.75 0.41 0.00 561.297.10LAND CLEARING EQUIPMENT, ROTARY CUTTER, 20' WIDE, 2 - 14" HEIGHT (ADD FARM 90 HP TRACTOR)

ROME PLOW CO.

RV8NL10RM001 $51,366 4.11 0.96 0.00 1343.0211.20LAND CLEARING EQUIPMENT, V-TREE CUTTER (ADD 275 - 325 HP TRACTOR DOZER)

MA-152R-8SL10RM002 $46,342 3.71 0.87 0.00 1502.739.75LAND CLEARING EQUIPMENT, MULTI-APPLICATION RAKE, 12' 8'' WIDE, 9 TEETH (ADD 275 - 325 HP TRACTOR DOZER)

EP 1110-1-8, Vol. 130 Nov 09

2-143


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

VERMEER MANUFACTURING CO.

27SC 252L10VE010 $12,557 0.99 0.24 4.39 110.747.67LAND CLEARING EQUIPMENT, STUMPER, 16" DIA WHEEL, TRAILER MTD

HP G


HP G


HP D-off

13TS-30L10VE005 $12,253 0.95 0.23 2.11 380.714.99LAND CLEARING EQUIPMENT, TREE SPADE, 30" DIA, 26" DEPTH, TRAILER MTD

HP G

20TS-44AL10VE006 $32,018 2.53 0.60 3.25 661.8710.45LAND CLEARING EQUIPMENT, TREE SPADE, 44" DIA, 40" DEPTH, TRAILER MTD

HP G

TS-50L10VE007 $27,573 2.21 0.52 0.00 811.637.30LAND CLEARING EQUIPMENT, TREE SPADE, 50" DIA, 48" DEPTH (ADD 13,800 GVW TRUCK)

LANDSCAPING EQUIPMENTL150.00 LANDSCAPING EQUIPMENTSUBCATEGORY

BOWIE INDUSTRIES, INC.

25LANCER 500L15BW001 $16,448 3.42 0.34 5.42 252.0513.38LANDSCAPING EQUIPMENT, 500 GAL, HYDROMULCHER, TRAILER MTD

HP G

35VICTOR 800L15BW002 $29,660 6.16 0.61 7.59 483.6921.70LANDSCAPING EQUIPMENT, 800 GAL, HYDROMULCHER, TRAILER MTD

HP G

50VICTOR 1100L15BW003 $34,065 7.10 0.70 10.84 604.2527.30LANDSCAPING EQUIPMENT, 1,100 GAL, HYDROMULCHER, GOOSENECK TRAILER MTD

HP G

EP 1110-1-8, Vol. 130 Nov 09

2-144


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

L15 BOWIE INDUSTRIES, INC. (continued)90IMPERIAL 3000L15BW004 $48,468 10.30 1.00 10.84 886.1533.84LANDSCAPING EQUIPMENT, 3,000 GAL,

HYDROMULCHER, TRUCK MTD (ADD 55,000 GVW TRUCK)

HP D-off

FINN CORPORATION

115T330L15FG001 $185,339 39.38 3.83 19.75 9623.52105.24310 HP D-offLANDSCAPING EQUIPMENT, 3,000 GAL, HYDROSEEDER, TRUCK MTD (INCLUDES 56,000 GVW TRUCK)

HP D-off

115B260TL15FG002 $42,533 8.93 0.88 13.85 485.3534.48LANDSCAPING EQUIPMENT, MULCHER, STRAW BLOWER, 20 TONS PER HOUR, TRAILER MOUNTED

HP D-off

HOFFCO-COMET

3PH980EL15HZ001 $807 0.17 0.02 0.65 10.111.08POST HOLE DRILL, UP TO 8" DIA, 30" DEEP, ONE MAN OPERATION

HP G

DEERE & COMPANY

20F725L15JD001 $10,967 1.61 0.23 4.33 121.0410.21LANDSCAPING EQUIPMENT, LAWNMOWER, 54" DECK, SIDE DISCHARGE RIDING, 4X2

HP G

MX5L15JD005 $2,204 0.47 0.05 0.00 80.291.00LANDSCAPING EQUIPMENT, ROTARY MOWER, 60" WIDE, MEDIUM DUTY, PTO DRIVE (ADD 45 - 100 HP AGRICULTURAL TRACTOR)

609L15JD006 $4,084 0.87 0.08 0.00 120.521.83LANDSCAPING EQUIPMENT, ROTARY MOWER, 60" WIDE, HEAVY DUTY, PTO DRIVE (ADD 45 - 100 HP AGRICULTURAL TRACTOR)

EP 1110-1-8, Vol. 130 Nov 09

2-145


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

TORO

622188 - PRO-LINE 21"

L15TO001 $1,302 0.28 0.03 1.30 10.172.04LANDSCAPING EQUIPMENT, LAWNMOWER, 21" DECK, REAR BAGGER, PUSH MOWER

HP G

1530092 MID-SIZEL15TO002 $3,967 0.75 0.08 3.25 60.465.44LANDSCAPING EQUIPMENT, LAWNMOWER, 32" DECK, SIDE DISCHARGE, WALK BEHIND MOWER

HP G

2174448L15TO003 $7,628 1.53 0.16 4.55 120.938.54LANDSCAPING EQUIPMENT, LAWNMOWER, 48" DECK, SIDE DISCHARGE, RIDING MOWER

HP G

2174449L15TO004 $8,140 1.65 0.17 4.55 131.008.77LANDSCAPING EQUIPMENT, LAWNMOWER, 52" DECK W/Z100 TRACTOR, SIDE DISCHARGE, RIDING MOWER

HP G

2974253L15TO006 $15,029 3.06 0.31 6.28 151.8413.84LANDSCAPING EQUIPMENT, LAWNMOWER, 60" DECK W/Z500 TRACTOR, SIDE DISCHARGE, RIDING MOWER

HP G

2974254L15TO007 $15,509 3.16 0.32 6.28 171.9014.05LANDSCAPING EQUIPMENT, LAWNMOWER, 72" DECK, W/Z500 TRACTOR, SIDE DISCHARGE, RIDING MOWER

HP G

WILLMAR EQUIPMENT COMPANY

S-200L15WI001 $8,109 1.64 0.17 0.00 150.993.66LANDSCAPING EQUIPMENT, SPREADER, 70 CF DRY CHEMICAL (ADD 55 HP FARM TRACTOR)

EP 1110-1-8, Vol. 130 Nov 09

2-146


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

LIGHTING SETS, TRAILER MOUNTEDL200.10 METALLIC VAPORSUBCATEGORY

ALLMAND BROTHERS INC.

13MAXI-LITE 7.5/8L20AB017 $13,442 1.32 0.26 1.74 210.926.65LITE SET, TRAILER MTD., 4/1250W, W/7.5 KW GEN, ELECTRIC MAST WINCH

HP D-off

14MAXI-LITE 7.5/8 CSA

L20AB018 $14,967 1.47 0.29 1.86 211.037.31LITE SET, TRAILER MTD., 4/1,000W, W/8 KW GEN, ELECTRIC MAST WINCH

HP D-off

14MAXI-LITE 7.5/8 CSA

L20AB019 $17,539 1.73 0.34 1.86 211.218.22LITE SET, TRAILER MTD., 6/1,000W, W/8 KW GEN, ELECTRIC MAST WINCH

HP D-off

12NIGHT-LITE PRO

L20AB020 $11,344 1.11 0.22 1.49 200.785.63LITE SET, TRAILER MTD., 4/1,000W, W/6 KW GEN, MANUAL MAST WINCH

HP D-off

14NIGHT-LITE PRO CSA

L20AB021 $11,984 1.17 0.23 1.86 200.826.26LITE SET, TRAILER MTD., 4/1,000W, W/8 KW GEN, MANUAL MAST WINCH

HP D-off

13NIGHT-LITE PR0 V

L20AB022 $13,517 1.32 0.26 1.74 210.926.67LITE SET, TRAILER MTD., 4/1,000W, W/7.5 KW GEN, ELECTRIC MAST WINCH

HP D-off

ECLIPSE 2220/SE ALT

L20AB023 $5,564 0.54 0.11 0.00 120.381.95LITE SET, TRAILER MTD., 15 LED LAMP, FLASHING ARROW, W/TWO 8D BATTERIES AND 50W SOLAR ARRAY

ECLIPSE 2220/SE APF

L20AB024 $5,957 0.58 0.11 0.00 120.402.09LITE SET, TRAILER MTD., 25 LED LAMP, FLASHING ARROW, W/TWO 8D BATTERIES AND 50W SOLAR ARRAY

EP 1110-1-8, Vol. 130 Nov 09

2-147


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

LINE STRIPING EQUIPMENTL250.00 LINE STRIPING EQUIPMENTSUBCATEGORY

JCL EQUIPMENT CO.

134-BL25JE001 $11,549 1.15 0.22 3.01 150.806.86LINE STRIPING EQUIPMENT, STRIPER, INTERMEDIATE, 2 GUNS, SELF PROPELLED, SINGLE COLOR

HP G

230ROAD RUNNERL25JE002 $98,383 9.71 1.88 29.89 1166.7463.28LINE STRIPING EQUIPMENT, STRIPER, INTERMEDIATE, 3 GUNS, TRUCK MOUNTED (11,000 LB GVW), TWO COLORS

HP D-off

M-B COMPANIES, INC.

55-10L25MB002 $6,124 0.49 0.12 1.16 60.374.21LINE STRIPING EQUIPMENT, STRIPER, 1 GUN, WALK-BEHIND, SINGLE COLOR

HP G

105-12AL25MB005 $11,159 0.99 0.21 2.32 60.717.02LINE STRIPING EQUIPMENT, STRIPER, 2 GUNS, WALK BEHIND, SINGLE COLOR

HP G

23220L25MB007 $51,979 5.20 1.00 5.33 303.6022.76LINE STRIPING EQUIPMENT, STRIPER, INTERMEDIATE, 3-4 GUNS, SELF PROPELLED, THREE COLORS

HP G

60245L25MB006 $92,599 9.26 1.77 13.91 486.4044.91LINE STRIPING EQUIPMENT, STRIPER, INTERMEDIATE, 3 GUNS, SELF PROPELLED, TWO COLORS

HP G

190VANMARK 360L25MB004 $152,450 15.12 2.92 44.04 13310.4897.00LINE STRIPING EQUIPMENT, STRIPER, INTERMEDIATE, 3-4 GUNS, W/11,000 LBS GVW TRUCK, TWO COLORS

HP G

EP 1110-1-8, Vol. 130 Nov 09

2-148


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

L25 M-B COMPANIES, INC. (continued)190360L25MB008 $166,575 16.30 3.19 24.69 8011.3479.86LINE STRIPING EQUIPMENT, STRIPER,

INTERMEDIATE, 3-4 GUNS, THERMAL 120 GAL, TRUCK MTD, TWO COLORS

HP D-off

LOADERS, BELT (Conveyor belts) & ACCESSORIESL300.00 LOADERS, BELT (Conveyor belts) & ACCESSORIESSUBCATEGORY

HEWITT-ROBINS

25V-11 6X16FT, TDL30HW015 $141,369 11.05 2.65 2.31 1388.1835.18LOADER, CONVEYOR BELT & ACCESSORIES, SCREENING PLANT, W/6' X 16' VIBRATORY SLOPE TRIPLE DECK SCREENS/36"X 16.5' UNDER SCREEN CONVEYOR/ 7 CY HOPPER/ & FEEDER

HP E


1511-2450L30KB001 $33,615 2.60 0.63 1.38 571.939.66LOADER, CONVEYOR BELT & ACCESSORIES, COVEYOR 50', MOBILE, CONCRETE & AGGREGATE, 24'' WIDE

HP E

1511-2460L30KB002 $35,409 2.74 0.66 1.38 622.0310.05LOADER, CONVEYOR BELT & ACCESSORIES, CONVEYOR, 60', MOBILE, CONCRETE & AGGREGATE, 24'' WIDE

HP E

METSO MINERALS

25CV50DL30RA001 $72,638 5.72 1.36 2.46 1304.2219.01LOADER, CONVEYOR BELT & ACCESSORIES, GRIZZLY SINGLE SCREEN, 40 CY/HR TRAILER MTD

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-149


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

SUPERIOR INDUSTRIES, AN ASTEC COMPANY

1536''X35' FEED CONVEY

L30S4001 $18,450 1.48 0.35 1.38 331.096.23LOADER, CONVEYOR BELT & ACCESSORIES, BELT FEEDER

HP E

RUN-ON HYDRAULIC LEG

L30S4002 $21,066 1.69 0.40 0.00 281.254.69LOADER, CONVEYOR BELT & ACCESSORIES, 4 HYDRAULIC JACK LEGS

SIDE SKIRTING UPPER

L30S4003 $1,556 0.12 0.03 0.00 90.090.34LOADER, CONVEYOR BELT & ACCESSORIES, SIDE GUARD, ONE SIDE, UPPER

SIDE SKIRTING LOWER

L30S4004 $2,625 0.21 0.05 0.00 90.160.58LOADER, CONVEYOR BELT & ACCESSORIES, SIDE GUARD, ONE SIDE, LOWER

TELSMITH INC.

12PTC 24IN X 50FT

L30TS001 $37,833 2.84 0.71 1.11 102.1310.31LOADER, CONVEYOR BELT & ACCESSORIES, CONVEYOR, TRUSS FRAME, 24"W X 50'L, WHEEL MTD, 300 TPH

HP E

LOADERS, FRONT END, CRAWLER TYPEL350.00 LOADERS, FRONT END, CRAWLER TYPESUBCATEGORY


90939-CL35CA013 $123,264 9.86 2.31 9.70 2097.2439.77LOADER, FRONT END, CRAWLER, 1.50 CY BUCKET

HP D-off

148953-DL35CA005 $202,624 16.21 3.80 15.95 33411.9165.38LOADER, FRONT END, CRAWLER, 2.25 CY BUCKET

HP D-off

160963-DL35CA014 $276,537 22.12 5.19 17.24 43316.2584.19LOADER, FRONT END, CRAWLER, 3.20 CY BUCKET

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-150


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

L35 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

242973-CL35CA007 $382,166 30.57 7.17 26.08 58122.46118.86LOADER, FRONT END, CRAWLER, 3.70 CY BUCKET

HP D-off


200D75S-5L35KM006 $450,135 36.01 8.44 21.56 48526.45129.80LOADER, FRONT END, CRAWLER, 3.30 CY BUCKET

HP D-off

LOADERS, FRONT END, WHEEL TYPEL400.11 ARTICULATED, 0 THRU 225 HPSUBCATEGORY


52904BL40CA032 $46,426 3.59 0.91 5.11 982.7115.12LOADER, FRONT END, WHEEL, 0.80 CY BUCKET, ARTICULATED, 4X4

HP D-off

68906L40CA033 $60,947 4.77 1.19 6.68 1093.5819.70LOADER, FRONT END, WHEEL, 1.00 CY BUCKET, ARTICULATED, 4X4

HP D-off

76908L40CA034 $71,314 5.33 1.39 7.47 1334.0624.89LOADER, FRONT END, WHEEL, 1.30 CY BUCKET, ARTICULATED, 4X4

HP D-off

95914GL40CA019 $99,933 7.91 1.95 9.34 1755.9130.73LOADER, FRONT END, WHEEL, 1.70 CY BUCKET, ARTICULATED, 4X4

HP D-off

128924HzL40CA022 $138,702 11.04 2.70 12.58 2428.2241.92LOADER, FRONT END, WHEEL, 2.20 CY BUCKET, ARTICULATED, 4X4

HP D-off

149928HzL40CA015 $137,525 10.95 2.68 14.64 2768.1644.02LOADER, FRONT END, WHEEL, 2.60 CY BUCKET, ARTICULATED, 4X4

HP D-off

180938HL40CA023 $169,270 13.20 3.30 17.69 3329.9054.97LOADER, FRONT END, WHEEL, 3.65 CY BUCKET, ARTICULATED, 4X4

HP D-off


HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-151


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

L40 CATERPILLAR INC. ( MACHINE DIVISION) (continued)


HP D-off

CASE CORPORATION

136621DL40CS009 $155,467 12.23 3.03 13.36 2619.1546.77LOADER, FRONT END, WHEEL, 2.5 CY BUCKET, ARTICULATED, 4X4

HP D-off

181721DL40CS010 $185,266 14.65 3.61 17.79 30610.9457.54LOADER, FRONT END, WHEEL, 3.0 CY BUCKET, ARTICULATED, 4X4

HP D-off

187821CL40CS011 $233,960 18.20 4.56 18.38 37913.6669.32LOADER, FRONT END, WHEEL, 3.5 CY BUCKET, ARTICULATED, 4X4

HP D-off


75WA95-3L40KM015 $87,311 6.79 1.70 7.37 1285.1025.82LOADER, FRONT END, WHEEL, 1.40 CY BUCKET, ARTICULATED, 4X4

HP D-off


HP D-off

0.12 ARTICULATED, OVER 225 HPSUBCATEGORY


300980G IIL40CA007 $467,815 26.14 8.59 29.48 66021.66109.41LOADER, FRONT END, WHEEL, 6.00 CY BUCKET, ARTICULATED, 4X4

HP D-off

618990 SERIES IIL40CA018 $1,173,905 65.38 21.54 60.73 1,62854.23239.57LOADER, FRONT END, WHEEL, 11.00 CY BUCKET, ARTICULATED, 4X4

HP D-off

800992-GL40CA009 $1,622,983 89.22 29.79 78.62 2,02374.40327.33LOADER, FRONT END, WHEEL, 16.00 CY BUCKET, ARTICULATED, 4X4

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-152


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT



HP D-off

490WA600-3L40KM009 $674,336 37.21 12.38 48.15 1,01930.99152.64LOADER, FRONT END, WHEEL, 8.00 CY BUCKET, ARTICULATED, 4X4

HP D-off

684WA700-3L40KM010 $1,096,345 60.78 20.12 67.22 1,57450.51235.64LOADER, FRONT END, WHEEL, 11.10 CY BUCKET, ARTICULATED, 4X4

HP D-off

853WA800-3L40KM011 $1,408,229 76.49 25.85 83.82 2,23064.10302.54LOADER, FRONT END, WHEEL, 13.10 CY BUCKET, ARTICULATED, 4X4

HP D-off

0.20 SKID STEERSUBCATEGORY


49216BL40CA028 $30,829 2.92 0.59 5.28 542.0514.11LOADER, FRONT END, WHEEL, SKID-STEER, 13.0 CF, 60" BUCKET, 4X4

HP D-off


HP D-off


HP D-off

74246CL40CA031 $37,705 3.55 0.72 7.98 742.5019.08LOADER, FRONT END, WHEEL, SKID-STEER, 15.4 CF, 72" BUCKET, 4X4

HP D-off

MELROE COMPANY/BOBCAT

24S70L40ME016 $16,362 1.58 0.31 2.53 281.107.06LOADER, FRONT END, WHEEL, SKID-STEER, 6.5 CF, 44" BUCKET, 4X4

HP D-off


HP D-off

46S175L40ME012 $26,622 2.59 0.51 4.96 621.8112.35LOADER, FRONT END, WHEEL, SKID-STEER, 14.3 CF, 60" BUCKET

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-153


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

L40 MELROE COMPANY/BOBCAT (continued)49S130L40ME021 $23,309 2.17 0.45 5.28 521.5412.27LOADER, FRONT END, WHEEL, SKID-

STEER, 13.0 CF, 54" BUCKET, 4X4 HP D-off


HP D-off


HP D-off

0.31 TOOL CARRIER & TELESCOPIC HANDLERS, 0 THRU 225 HPSUBCATEGORY


90IT14GL40CA013 $116,938 8.59 2.27 8.84 1806.5734.10LOADER, WHEEL, INTEGRATED TOOL CARRIER, 1.75 CY LOADER; 6,303 LB @ 12.17' HIGH, FORK LIFT, OR 1,841 LB @ 22.42' HIGH, MATERIAL HANDLING ARM

HP D-off

145IT38HL40CA012 $186,420 13.79 3.61 14.25 27910.5154.06LOADER, WHEEL, INTEGRATED TOOL CARRIER, 2.50 CY LOADER; 10,640 LB @ 12.58' HIGH FORK LIFT, OR 3,195 LB @ 23.25' HIGH, MATERIAL HANDLING ARM

HP D-off

200IT62G IIL40CA014 $259,308 19.21 5.03 19.65 45414.6474.96LOADER, WHEEL, INTEGRATED TOOL CARRIER, 4.25 CY LOADER; 13,670 LB @ 12.42' HIGH, FORK LIFT, OR 5,040 LB @ 22.67' HIGH, MATERIAL HANDLING ARM

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-154


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

LOADERS / BACKHOE, WHEEL TYPEL500.00 LOADERS / BACKHOE, WHEEL TYPESUBCATEGORY


78416EL50CA001 $61,535 4.40 1.19 5.93 1623.3921.17LOADER / BACKHOE, WHEEL, 1.00 CY FRONT END BUCKET, 18" DIP, 4.5 CF, 14.5' DIGGING DEPTH, 4X2

HP D-off

110446DL50CA004 $147,647 10.66 2.86 8.37 1938.1941.75LOADER / BACKHOE, WHEEL, 1.50 CY FRONT END BUCKET, 36" DIP, 19 CF, 17.1' DIGGING DEPTH, 4X2

HP D-off

CASE CORPORATION

90580 SUPER M SERIES 2

L50CS005 $93,380 6.72 1.81 6.85 1435.1728.82LOADER / BACKHOE, WHEEL, 1.00 CY FRONT END BUCKET, 24" DIP, 6.2 CF, 14.25' DIGGING DEPTH, 4X4

HP D-off

98590 SUPER M SERIES 2

L50CS006 $112,220 8.09 2.18 7.46 1536.2333.48LOADER / BACKHOE, WHEEL, 1.30 CY FRONT END BUCKET, 24" DIP, 6.4 CF, 18' DIGGING DEPTH, 4X4, EXTENDAHOE

HP D-off

JCB INC.

67212S (4WS)L50JC001 $70,575 5.17 1.37 5.10 1203.9621.56LOADER / BACKHOE, WHEEL, 0.80 CY FRONT END BUCKET, 24" DIP, 4.3 CF, 12' DIGGING DEPTH, 4X4

HP D-off

92214S (2WD)L50JC002 $80,572 5.76 1.56 7.00 1584.4426.56LOADER / BACKHOE, WHEEL, 1.25 CY FRONT END BUCKET, 24" DIP, 7.1 CF, 14.6' DIGGING DEPTH, 4X2

HP D-off

100214S (4WS)L50JC003 $97,739 6.98 1.89 7.61 1645.3831.03LOADER / BACKHOE, WHEEL, 1.40 CY FRONT END BUCKET, 24" DIP, 7.1 CF, 14.6' DIGGING DEPTH, 4X4

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-155


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

L50 JCB INC. (continued)100215S (4WS)L50JC005 $113,226 8.14 2.19 7.61 1766.2634.03LOADER / BACKHOE, WHEEL, 1.40 CY

FRONT END BUCKET, 24" DIP, 7.1 CF, 20.1' DIGGING DEPTH, 4X4

HP D-off

100217S (4WS)L50JC007 $144,758 10.47 2.81 7.61 1788.0540.23LOADER / BACKHOE, WHEEL, 1.60 CY FRONT END BUCKET, 24" DIP, 7.1 CF, 21.5' DIGGING DEPTH, 4X4

HP D-off

LOADER / BACKHOE, ATTACHMENTSL550.00 LOADER / BACKHOE, ATTACHMENTSSUBCATEGORY


175KB-555L55KN001 $6,862 0.91 0.14 0.00 60.602.98LOADER / BACKHOE, ATTACHMENT, AIR RAM, 500 FT-LB, W/2.5" DIA. POINT (ADD 175 CFM COMPRESSOR & LDR/BH)

CFM A

250KB-999L55KN002 $14,049 1.87 0.28 0.00 101.226.10LOADER / BACKHOE, ATTACHMENT, AIR RAM, 1000 FT-LB, W/ 3.5" DIA. POINT (ADD 250 CFM COMPRESSOR & LDR/BH)

CFM A

KF6TLBL55KN004 $13,012 1.73 0.26 0.00 71.134.67LOADER / BACKHOE, ATTACHMENT, HYDRA RAM, 1000 FT-LB, W/3'' DIA. POINT (ADD 12,000-14,000 LB LDR/BH)

KF9TLBL55KN005 $19,205 2.56 0.38 0.00 111.666.89LOADER / BACKHOE, ATTACHMENT, HYDRA RAM, 1500 FT-LB, W/3.5'' DIA. POINT (ADD 14,000-20,000 LB LDR/BH)

KF12TLBL55KN006 $28,616 3.82 0.57 0.00 192.4810.28LOADER / BACKHOE, ATTACHMENT, HYDRA RAM, 2000 FT-LB, W/4.25'' DIA. POINT (ADD 20,000-30,000 LB LDR/BH)

EP 1110-1-8, Vol. 130 Nov 09

2-156


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

LOG SKIDDERSL600.00 LOG SKIDDERSSUBCATEGORY


120517 GRAPPLEL60CA014 $285,137 24.24 5.18 11.79 40517.3068.41LOG SKIDDER, 8 SF GRAPPLE, CABLE 41,050 LBS LINE-PULL AND WINCH, CRAWLER

HP D-off

160525 BL60CA013 $228,193 18.63 4.14 15.72 35813.4663.04LOG SKIDDER, 11 SF GRAPPLE, CABLE 43,000 LBS LINE-PULL AND WINCH, WHEEL, 4X2

HP D-off

150527 CABLEL60CA010 $327,227 27.81 5.94 14.74 40719.8579.87LOG SKIDDER, CABLE, 69,200 LBS LINE-PULL AND WINCH, BLADE, CRAWLER

HP D-off

150527 GRAPPLEL60CA011 $391,398 33.27 7.10 14.74 47323.7492.26LOG SKIDDER, 10 SF GRAPPLE, CABLE 69,200 LBS LINE-PULL AND WINCH, CRAWLER

HP D-off

DEERE & COMPANY

119540G II - SKIDDER

L60JD001 $153,771 12.26 2.79 11.69 2198.9244.78LOG SKIDDER, CABLE, 40,525 LBS LINE-PULL WINCH AND BLADE, WHEEL, 4X4

HP D-off

119548G III - GRAPPLE

L60JD003 $150,080 11.95 2.72 11.69 2178.7044.07LOG SKIDDER, 8.0 SF GRAPPLE WITH BLADE, WHEEL, 4X4

HP D-off

160648G III - GRAPPLE

L60JD004 $198,891 15.64 3.61 15.72 26611.4359.08LOG SKIDDER, 10.4 SF GRAPPLE WITH BLADE, WHEEL, 4X4

HP D-off

151640G III - SKIDDER

L60JD002 $182,271 14.68 3.31 14.84 23910.6553.84LOG SKIDDER, CABLE, 48,867 LBS LINE-PULL WINCH AND BLADE, WHEEL, 4X4

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-157


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

L60 DEERE & COMPANY (continued)170643HL60JD006 $240,224 19.34 4.36 16.71 32014.0367.76LOG SKIDDER, LOG FELLER/BUNCHER,

18" DIA TREE SAW CUTTER, WHEEL, 4X4

HP D-off

170653GL60JD008 $345,167 29.34 6.27 16.71 41020.9485.57LOG SKIDDER, LOG FELLER/BUNCHER, 28" DIA TREE SAW CUTTER, CRAWLER

HP D-off

200843GL60JD007 $262,750 21.25 4.77 19.65 32315.4075.43LOG SKIDDER, LOG FELLER/BUNCHER, 20" DIA TREE SAW CUTTER, WHEEL, 4X4

HP D-off

MARINE EQUIPMENT (NON DREDGING)M100.41 WORK FLOATS (NON-DREDGING)SUBCATEGORY

MARINE INLAND FABRICATORS

M10MZ001 $18,418 2.76 0.34 0.00 1431.725.03MARINE EQUIPMENT, WORK BARGE, SECTIONAL, MEDIUM DUTY, 40' X 8' X 4', 23 TON


0.42 WORK BARGES (SECTIONAL, NON-DREDGING)SUBCATEGORY


RAKEM10MZ005 $26,049 0.78 0.43 0.00 1930.821.87MARINE EQUIPMENT, WORK BARGE, SECTIONAL, MEDIUM DUTY', W/ONE BUCKHEAD AND SPUDS, 40' X 12' X 4', 36 TON

EP 1110-1-8, Vol. 130 Nov 09

2-158


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

M10 MARINE INLAND FABRICATORS (continued)



M10XX001 $6,138 0.18 0.10 0.00 10.190.43MARINE EQUIPMENT, WORK BARGE, SECTIONAL, BOW AND STERN SECTIONS

M10XX002 $19,076 0.57 0.31 0.00 10.601.36MARINE EQUIPMENT, WORK BARGE, SECTIONAL, LOADING RAMPS

M10XX003 $23,038 0.69 0.38 0.00 10.731.65MARINE EQUIPMENT, WORK BARGE, SECTIONAL, MID-SECTION, 20' X 10' X 5'

M10XX004 $37,329 1.12 0.61 0.00 11.172.67MARINE EQUIPMENT, WORK BARGE, SECTIONAL, MID-SECTION, 40' X 10' X 5'

0.45 FLAT-DECK OR CARGO BARGE (NON-DREDGING)SUBCATEGORY


M10XX005 $161,012 1.70 2.46 0.00 13.315.51MARINE EQUIPMENT, FLAT-DECK CARGO BARGE, 120' X 30' X 7.25', 400 TON

M10XX006 $226,636 2.39 3.46 0.00 14.667.75MARINE EQUIPMENT, FLAT-DECK CARGO BARGE, 120' X 45' X 7', 800 TON

M10XX007 $288,282 3.04 4.40 0.00 15.929.86MARINE EQUIPMENT, FLAT-DECK CARGO BARGE, 140' X 45' X 7', 900 TON

M10XX008 $400,085 4.22 6.10 0.00 18.2113.68MARINE EQUIPMENT, FLAT-DECK CARGO BARGE, 150' X 45' X 9', 1,100 TON

EP 1110-1-8, Vol. 130 Nov 09

2-159


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

0.48 ALL OTHER BARGES (NON-DREDGING)SUBCATEGORY


OPEN 195M10XX016 $240,588 7.62 3.77 0.00 17.5818.46MARINE EQUIPMENT, ALL OTHER BARGES, HOPPER, 195' X 35' X 12', 1,400 TON

OPEN 200M10XX017 $254,372 8.06 3.99 0.00 18.0219.52MARINE EQUIPMENT, ALL OTHER BARGES, HOPPER, 200' X 35' X 12', 1,600 TON

CLOSED 195M10XX018 $316,824 10.03 4.97 0.00 19.9924.30MARINE EQUIPMENT, ALL OTHER BARGES, HOPPER, 195' X 35' X 12', 1,400 TON (COVERED)

CLOSED 200M10XX019 $323,734 10.25 5.08 0.00 110.2124.84MARINE EQUIPMENT, ALL OTHER BARGES, HOPPER, 200' X 35' X 12', 1,600 TON (COVERED)

0.51 BOATS & LAUNCHES, 0 THRU 250 HPSUBCATEGORY


140COLTM10MZ010 $48,256 2.56 0.85 13.76 952.1322.31MARINE EQUIPMENT, BOATS & LAUNCHES, TRUCKABLE WORKBOAT W/PILOT HOUSE & PUSH KNEES, INBOARD, 20.25' X 8' X 3'

HP D-off

210MUSTANGM10MZ011 $68,969 3.66 1.21 20.64 1903.0433.04MARINE EQUIPMENT, BOATS & LAUNCHES, TRUCKABLE WORKBOAT W/PILOT HOUSE & PUSH KNEES, INBOARD, 25.25' X 10' X 3.5'

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-160


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

SEAARK MARINE

11518' - 72 SERIESM10SM005 $26,388 1.40 0.46 20.42 151.1626.83MARINE EQUIPMENT, BOATS & LAUNCHES, 18' RIVER RUNNER, VEE HULL, NO CABIN, CAP 1,350 LBS, OUTBOARD, 18' X 7.9' X 0.5'

HP G

20019' - UTILITY SERIES

M10SM008 $47,914 2.55 0.84 35.52 172.1246.94MARINE EQUIPMENT, BOATS & LAUNCHES, 19' ROUSTABOUT, TRI HULL, NO CABIN, CAP 2,600 LBS, OUTBOARD, 19.4' X 8.5' X 0.8'

HP G


M10SM001 $57,171 3.04 1.00 26.64 182.5237.88MARINE EQUIPMENT, BOATS & LAUNCHES, 17' LITTLE GIANT, W/CABIN TRI-HULL, CAP 2,000 LBS, OUTBOARD, 17.5' X 7.25' X 0.7'

HP G


M10SM003 $70,945 3.77 1.24 35.52 243.1349.83MARINE EQUIPMENT, BOATS & LAUNCHES, 21' LITTLE GIANT, W/CABIN TRI-HULL, CAP 2,800 LBS, OUTBOARD, 21.4' X 8.5' X 1'

HP G


M10SM004 $76,222 4.05 1.34 44.40 283.3760.73MARINE EQUIPMENT, BOATS & LAUNCHES, 23' LITTLE GIANT, W/CABIN TRI-HULL, CAP 3,400 LBS, OUTBOARD, 23.4' X 8.5' X 1.2'

HP G


7512M10XX010 $48,183 2.56 0.84 7.37 12.1214.75MARINE EQUIPMENT, BOATS & LAUNCHES, 12' TENDER, 7' BEAM, INBOARD ENGINE

HP D-off

5013M10XX009 $14,448 0.77 0.25 8.88 130.6412.05MARINE EQUIPMENT, BOATS & LAUNCHES, 13' RUNABOUT, 5' BEAM, OUTBOARD ENGINE

HP G

10014M10XX011 $55,388 2.94 0.97 9.83 132.4418.56MARINE EQUIPMENT, BOATS & LAUNCHES, 14' TENDER, 7' BEAM, INBOARD ENGINE

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-161


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

M10 NO SPECIFIC MANUFACTURER (continued)100100M10XX012 $56,424 3.00 0.99 9.83 132.4918.70MARINE EQUIPMENT, BOATS &

LAUNCHES, 16', SHALLOW DRAFT, INLAND TUG

HP D-off

115115M10XX013 $73,113 3.88 1.28 11.30 233.2222.53MARINE EQUIPMENT, BOATS & LAUNCHES, 22', SHALLOW DRAFT, INLAND TUG

HP D-off

175175M10XX014 $100,601 5.34 1.76 17.20 604.4332.95MARINE EQUIPMENT, BOATS & LAUNCHES, 18', W/STEERING NOZZLE, INLAND TUG

HP D-off

250250M10XX015 $126,211 6.70 2.21 24.57 835.5644.87MARINE EQUIPMENT, BOATS & LAUNCHES, 26', W/STEERING NOZZLE, INLAND TUG

HP D-off

0.53 BOATS & LAUNCHES, 251 THRU 500 HPSUBCATEGORY


380380M10XX021 $334,556 16.73 5.60 37.34 10013.9785.13MARINE EQUIPMENT, BOATS & LAUNCHES, 40', STANDARD RUDDER, INLAND TUG

HP D-off

435435M10XX022 $380,678 19.03 6.38 42.75 10015.9097.18MARINE EQUIPMENT, BOATS & LAUNCHES, 45' LENGTH, 16' BEAM, 5' 0" DRAFT, PUSH BOAT

HP D-off

400400M10XX023 $509,831 25.49 8.54 39.31 10021.29108.96MARINE EQUIPMENT, BOATS & LAUNCHES, 48' LENGTH, 20' BEAM, 6' 6" DRAFT PUSH BOAT

HP D-off

435435M10XX024 $726,971 36.35 12.17 42.75 13030.35139.66MARINE EQUIPMENT, BOATS & LAUNCHES, 58' LENGTH, 21' BEAM, 6' 0" DRAFT, PUSH BOAT

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-162


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

PILE HAMMER ACCESSORIES - EXTRACTORS & BOX LEADSP100.00 PILE HAMMER ACCESSORIES - EXTRACTORS & BOX LEADSSUBCATEGORY

INTERNATIONAL CONSTRUCTION EQUIPMENT,INC

175216P10IC001 $108,863 11.79 2.34 17.20 1308.2451.85PILE HAMMER ACCESSORIES, PILE EXTRACTOR, 30 TON LINE PULL (ADD LEADS & CRANE)

HP D-off

300416LP10IC002 $171,371 18.57 3.68 29.48 20712.9784.40PILE HAMMER ACCESSORIES, PILE EXTRACTOR, 40 TON LINE PULL (ADD LEADS & CRANE)

HP D-off

8001412BP10IC005 $456,908 49.50 9.81 78.62 59334.56225.03PILE HAMMER ACCESSORIES, PILE EXTRACTOR, 150 TON LINE PULL (ADD LEADS & CRANE)

HP D-off

P10IC010 $16,135 1.75 0.35 0.00 1011.234.75PILE HAMMER ACCESSORIES, PILE LEADS, SWING, 26" X 86'

P10IC012 $22,772 2.47 0.49 0.00 1551.736.71PILE HAMMER ACCESSORIES, PILE LEADS, SWING, 32" X 88'

13P10IC011 $31,752 3.44 0.68 1.28 1342.4010.81PILE HAMMER ACCESSORIES, PILE LEADS, FIXED, 26" X 86', W/SPOTTER

HP D-off

13P10IC013 $39,410 4.27 0.85 2.31 1932.9914.26PILE HAMMER ACCESSORIES, PILE LEADS, FIXED, 32" X 88', W/SPOTTER

HP G

EP 1110-1-8, Vol. 130 Nov 09

2-163


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

PILE HAMMERS, DOUBLE ACTINGP200.10 DIESELSUBCATEGORY


422P20IC002 $98,829 12.35 2.01 0.00 1228.1938.63PILE HAMMER, DOUBLE ACTING, DIESEL, 22,500 FT-LBS, MAX STROKE 5' 8" (ADD LEADS & CRANE)



MKT MANUFACTURING, INC.

DA-15CP20MK001 $60,162 7.52 1.22 0.00 604.9823.61PILE HAMMER, DOUBLE ACTING, DIESEL, 8,200 FT-LBS, MAX STROKE 10' 6" (ADD LEADS & CRANE)

0.20 PNUEMATIC (STEAM/AIR)SUBCATEGORY


2505P20MK002 $17,952 2.39 0.36 0.00 161.567.31PILE HAMMER, DOUBLE ACTING, PNUEMATIC (STEAM/AIR), 1,000 FT-LBS, MAX STROKE 7" (ADD 250 CFM COMPRESSOR, LEADS & CRANE)

CFM A

4006P20MK003 $22,629 3.02 0.45 0.00 301.969.59PILE HAMMER, DOUBLE ACTING, PNUEMATIC (STEAM/AIR), 2,500 FT-LBS, MAX STROKE 8.75" (ADD 400 CFM COMPRESSOR, LEADS & CRANE)

CFM A

EP 1110-1-8, Vol. 130 Nov 09

2-164


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

P20 MKT MANUFACTURING, INC. (continued)4507P20MK004 $28,036 3.74 0.56 0.00 512.4311.90PILE HAMMER, DOUBLE ACTING,

PNUEMATIC (STEAM/AIR), 4,150 FT-LBS, MAX STROKE 9.5" (ADD 450 CFM COMPRESSOR, LEADS & CRANE)

CFM A

6009B3P20MK005 $47,222 6.30 0.94 0.00 714.0919.18PILE HAMMER, DOUBLE ACTING, PNUEMATIC (STEAM/AIR), 8,750 FT-LBS, MAX STROKE 17" (ADD 600 CFM COMPRESSOR, LEADS & CRANE)

CFM A


CFM A


CFM A

PILE HAMMERS, SINGLE ACTINGP250.10 DIESELSUBCATEGORY

PILECO, INC.

D6-32P25DL001 $54,236 7.23 1.07 0.00 404.6920.40PILE HAMMER, SINGLE ACTING, DIESEL, 10,500 FT-LBS (ADD LEADS & CRANE)



EP 1110-1-8, Vol. 130 Nov 09

2-165


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

P25 PILECO, INC. (continued)D25-32P25DL005 $102,341 13.65 2.03 0.00 1308.8639.38PILE HAMMER, SINGLE ACTING, DIESEL,

58,248 FT-LBS (ADD LEADS & CRANE)







30SP25IC001 $67,618 9.02 1.34 0.00 735.8526.47PILE HAMMER, SINGLE ACTING, DIESEL, 22,500 FT-LBS (ADD LEADS & CRANE)



EP 1110-1-8, Vol. 130 Nov 09

2-166


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

P25 INTERNATIONAL CONSTRUCTION EQUIPMENT,INC (continued)





DE-33/30/20CP25MK001 $66,406 8.85 1.32 0.00 815.7526.33PILE HAMMER, SINGLE ACTING, DIESEL, 33,000 FT-LBS (ADD LEADS & CRANE)

DE-70/50CP25MK003 $110,150 14.69 2.18 0.00 1539.5343.67PILE HAMMER, SINGLE ACTING, DIESEL, 70,000 FT-LBS (ADD LEADS & CRANE)

0.20 PNUEMATIC (STEAM/AIR)SUBCATEGORY

VULCAN FOUNDATION EQUIPMENT, INC

750306P25VU002 $70,578 10.00 1.36 0.00 1216.3628.38PILE HAMMER, SINGLE ACTING, PNUEMATIC (STEAM/AIR), 18,000 FT-LBS (ADD 750 CFM COMPRESSOR, LEADS & CRANE)

CFM A


CFM A

EP 1110-1-8, Vol. 130 Nov 09

2-167


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

P25 VULCAN FOUNDATION EQUIPMENT, INC (continued)


CFM A


CFM A

1,050510P25VU010 $122,586 17.37 2.36 0.00 22211.0545.89PILE HAMMER, SINGLE ACTING, PNUEMATIC (STEAM/AIR), 50,000 FT-LBS (ADD 1,050 CFM COMPRESSOR, LEADS & CRANE)

CFM A

1,200512P25VU011 $124,139 17.59 2.39 0.00 24211.1946.68PILE HAMMER, SINGLE ACTING, PNUEMATIC (STEAM/AIR), 60,000 FT-LBS (ADD 1,200 CFM COMPRESSOR, LEADS & CRANE)

CFM A

PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORYP300.00 PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORYSUBCATEGORY


185V-5C/HP-185P30MK001 $94,375 12.58 1.87 18.18 1208.1654.80PILE HAMMER, DRIVER/EXTRACTOR, VIBRATORY, 53 TON FORCE DRIVE (ADD LEADS & CRANE)

HP D-off

325V-20B/HP-365P30MK003 $162,902 21.72 3.23 31.94 22014.0995.24PILE HAMMER, DRIVER/EXTRACTOR, VIBRATORY, 98.5 TON FORCE DRIVE (ADD LEADS & CRANE)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-168


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

P30 MKT MANUFACTURING, INC. (continued)630V-35/HP-630P30MK004 $275,346 36.71 5.46 61.91 32723.82170.11PILE HAMMER, DRIVER/EXTRACTOR,

VIBRATORY, 200 TON FORCE DRIVE (ADD LEADS & CRANE)

HP D-off

PIPELAYERSP350.00 PIPELAYERSSUBCATEGORY


110561MP35CA001 $220,427 12.60 4.04 5.93 35810.3442.23PIPELAYER, 18' BOOM, 40,000 LBS CAPACITY

HP D-off

230572-RP35CA008 $407,747 23.30 7.47 12.39 66919.1279.80PIPELAYER, 20' BOOM, 90,000 LBS CAPACITY

HP D-off

305583-RP35CA009 $530,170 30.30 9.71 16.44 98424.86104.15PIPELAYER, 20' BOOM, 140,000 LBS CAPACITY

HP D-off

420589P35CA006 $688,603 39.35 12.62 22.63 1,45032.30136.80PIPELAYER, 28' BOOM, 230,000 LBS CAPACITY

HP D-off

PLATFORMS & MAN-LIFTSP400.00 PLATFORMS & MAN-LIFTSSUBCATEGORY

BIL-JAX, INC.

SKYRIDER 15P40BX001 $13,180 1.48 0.24 0.00 180.983.33MAN-LIFT, TELESCOPIC MAST, 14.8' HEIGHT, 500 LBS, 24 VOLT DC, RECHARGABLE BATTERIES, SELF PROPELLED, 2.2' X 4' PLATFORM

EP 1110-1-8, Vol. 130 Nov 09

2-169


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

TEREX CORPORATION

32TA50RTP40TE003 $89,311 9.78 1.61 2.43 1546.5025.90MAN-LIFT, ARTICULATED BOOM, 55' HEIGHT, 500 LBS, 29' REACH, 4X4, SELF PROPELLED, 2.2' X 5' PLATFORM

HP D-off

44TA60RTP40TE004 $102,750 11.34 1.85 3.35 2417.5230.12MAN-LIFT, ARTICULATED BOOM, 66' HEIGHT, 500 LBS, 33' REACH, 4X4, SELF PROPELLED, 3' X 6' PLATFROM

HP D-off

66TB42P40TE005 $78,625 8.58 1.41 5.02 1315.7026.17MAN-LIFT, STRAIGHT BOOM, 43' HEIGHT, 650 LBS, 37' REACH, 4X4, SELF PROPELLED, 3' X 6' PLATFORM

HP D-off


HP D-off


HP D-off


HP D-off


HP D-off

210T-292P40TE010 $74,794 8.26 1.34 15.98 1155.4737.11MAN-LIFT, LINE-TRUCK, W/AERIAL 2' X 2.5' PLATFORM, 300 LBS, 34' HEIGHT, 23' RAD

HP D-off

210T-38PP40TE011 $82,406 9.00 1.48 15.98 1285.9839.31MAN-LIFT, LINE-TRUCK, W/AERIAL 2' X 2.5' PLATFORM, 300 LBS, 43' HEIGHT, 26' RAD

HP D-off

210Digger DerrickC-4045

P40TE012 $123,479 13.62 2.22 15.98 2689.0349.52MAN-LIFT, LINE-TRUCK, W/13.7 TON, 45' HIGH-BOOM TILT POLE CLAWS, & 1.5' DIA AUGER

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-170


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

P40 TEREX CORPORATION (continued)2105FC-52P40TE013 $113,019 12.44 2.03 15.98 2158.2546.91MAN-LIFT, LINE-TRUCK, W/AERIAL 2' X 4'

PLATFORM, 700 LBS, 57' HEIGHT, 35' RAD

HP D-off

2105FC-55P40TE014 $115,205 12.69 2.07 15.98 2488.4247.46MAN-LIFT, LINE-TRUCK, W/AERIAL 2' X 2.5' PLATFORM, 500 LBS, 60' HEIGHT, 38' RAD

HP D-off

2106H-65P40TE015 $130,692 14.43 2.35 15.98 2559.5751.31MAN-LIFT, LINE-TRUCK, W/AERIAL 2' X 4' PLATFORM, 750 LBS, 70' HEIGHT, 39' RAD

HP D-off

PUMPS, GROUTP450.00 PUMPS, GROUTSUBCATEGORY

AIRPLACO EQUIPMENT CO., INC.

HG-5P45AF002 $839 0.09 0.02 0.00 10.070.24PUMP, GROUT, HAND PUMP, 12 CF/HR, 0-100 PSI, W/O HOPPER (ADD HOSES)

HG-9P45AF003 $1,157 0.12 0.02 0.00 10.080.32PUMP, GROUT, HAND PUMP, 15 CF/HR, 0-100 PSI, W/5 GAL HOPPER (ADD HOSES)

5HGA-530P45AF008 $7,640 0.81 0.14 0.00 40.552.23PUMP, GROUT, 50 CF/HR, 0-250 PSI, SKID MTD, W/5 GAL HOPPER AND 30 GAL MIXER (ADD 50 CFM COMPRESSOR & HOSE)

CFM A

11HJ-15 SGP45AF005 $11,770 1.21 0.22 2.85 50.836.57PUMP, GROUT, HIGH PRESSURE SINGLE CYLINDER GROUT PUMP, 110 CF/HR, 400 PSI,GROUT-MUD JACKING-SHOTCRETE, TRAILER MTD, W/30 GAL HOPPER AND 30 GAL MIXER (ADD 200 CFM COMPRESSOR & 2" HOSE)

HP G

EP 1110-1-8, Vol. 130 Nov 09

2-171


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

P45 AIRPLACO EQUIPMENT CO., INC. (continued)

350MP-2J6/GM-70DA

P45AF009 $25,556 2.72 0.47 0.00 51.837.23PUMP, GROUT, 160 CF/HR, 1 - 225 PSI, SKID MTD, W/15 GAL HOPPER/ & TWO 70 GAL MIXERS (ADD 350 CFM COMPRESSOR & HOSE)

CFM A

11HJ-15 DGP45AF006 $15,243 1.58 0.28 2.85 71.077.54PUMP, GROUT, HIGH PRESSURE DUAL CYLINDER GROUT PUMP, 180 CF/HR, 0-300 PSI, GROUT-MUD JACKING-SHOTCRETE, TRAILER MTD, W/30 GAL HOPPER AND 30 GAL MIXER (ADD 200 CFM COMPRESSOR & 2" HOSE)

HP G

18HJ-25P45AF010 $30,096 3.16 0.56 4.66 232.1413.78PUMP, GROUT, HIGH PRESSURE DUAL CYLINDER GROUT PUMP, 180 CF/HR, 0 - 400 PSI, GROUT-MUD JACK-PLASTER, TRAILER MTD, W/100 GAL HOPPER AND 45 GAL MIXER/ 2" HOSE

HP G

35HJ-36 CRGP45AF011 $53,595 5.66 0.99 9.06 493.8225.40PUMP, GROUT, HIGH PRESSURE DUAL CYLINDER GROUT PUMP, 250 CF/HR, 0 - 250 PSI, GROUT-MUD JACK-SHOTCRETE, TRAILER MTD, W/120 GAL HOPPER/ 90 GAL MIXER/ 2" HOSE

HP G

30P-280 HDP45AF007 $33,185 3.50 0.62 4.28 252.3714.13PUMP, GROUT, HIGH VOLUME DUAL CYLINDER GROUT PUMP, 756 CF/HR CONCRETE, 486 CF/HR SHOTCRETE, TRAILER MTD, W/1200 GAL HOPPER (ADD HOSE 2" - 3" DIA)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-172


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

ALLENTOWN EQUIPMENT

46POWER CRETER MAGNUM

P45AL015 $59,684 6.31 1.11 6.56 354.2724.10PUMP, GROUT, GROUT-MUD JACK-SHOTCRE, HIGH PRESSURE DUAL CYLINDER GROUT PUMP, 135 CF/HR, 0 - 1,770 PSI, TRAILER MTD, W/75 GAL HOPPER/ 82 GAL MIXER/ 3" HOSE

HP D-off

CHEMGROUT, INC.

15CG-050P45CG001 $4,070 0.43 0.08 0.00 10.301.19PUMP, GROUT, MINI, AIR, 40 CF/HR, 225 PSI, PORTABLE, SKID MTD (ADD 15 CFM - 100 PSI COMPRESSOR)

CFM A

85CG-550PP45CG002 $6,596 0.70 0.12 0.00 30.471.94PUMP, GROUT, MIXER, AIR, 40 CF/HR, 225 PSI, SKID MTD (ADD 85 CFM - 100 PSI COMPRESSOR)

CFM A

230CG-500/2C6 VERSATILE

P45CG003 $15,302 1.63 0.28 0.00 121.104.42PUMP, GROUT, MIXER, AIR, 160 CF/HR, 160 PSI, SKID MTD, 15 GAL HOPPER & 2 - 70 GAL MIXING TANKS (ADD 250 CFM - 100 PSI COMPRESSOR)

CFM A

16CG-570 / 3C6 / HP45CG007 $22,373 2.38 0.42 4.14 131.6111.02PUMP, GROUT, THICK MIX/SPRAY, 64 CF/HR, 261 PSI, SKID MTD, 15 GAL HOPPER & 45 GAL MIXING TANK, W/AIR COMPRESSOR, POWER UNIT

HP G

16CG-570 / 3C6P45CG006 $27,928 2.93 0.52 4.14 151.9912.57PUMP, GROUT, THICK MIX/SPRAY, 64 CF/HR, 261 PSI, TRAILER MTD, 15 GAL HOPPER & 45 GAL MIXING TANK, W/AIR COMPRESSOR, POWER UNIT

HP G

OLIN ENGINEERING, INC.

555 40P45OE002 $34,519 3.60 0.64 7.85 422.4418.53PUMP, GROUT PUMP, 1,134 CF/HR, 750 PSI, 37 GAL HOPPER, TRAILER MTD, W/POWER UNIT

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-173


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

P45 OLIN ENGINEERING, INC. (continued)845 65P45OE003 $44,805 4.69 0.83 11.98 483.1826.08PUMP, GROUT PUMP, 1,836 CF/HR, 1100

PSI, 37 GAL HOPPER, TRAILER MTD, W/POWER UNIT

HP D-off

1205 85P45OE004 $53,559 5.62 0.99 17.12 563.8034.35PUMP, GROUT PUMP, 2,295 CF/HR, 1100 PSI, 37 GAL HOPPER, TRAILER MTD, W/POWER UNIT

HP D-off

1815 140CAP45OE005 $72,226 7.54 1.34 25.82 1005.1149.44PUMP, GROUT PUMP, 3,780 CF/HR, 900 PSI, 37 GAL HOPPER, TRAILER MTD TANDEM, W/POWER UNIT

HP D-off

PUMPS, WATER, CENTRIFUGAL, TRASHP500.11 ENGINE DRIVESUBCATEGORY

WACKER CORPORATION

10PT 2AP50WC001 $1,348 0.13 0.03 2.44 10.103.16PUMP, WATER, CENTRIFUGAL, TRASH, ENGINE DRIVE, 2" DIA, 205 GPM @ 100' HEAD (ADD HOSES)

HP G

15PT 3AP50WC002 $1,587 0.16 0.03 2.04 20.112.82PUMP, WATER, CENTRIFUGAL, TRASH, ENGINE DRIVE, 3" DIA, 425 GPM @ 95' HEAD (ADD HOSES)

HP D-off

16PTS 4VP50WC003 $3,691 0.37 0.07 2.18 30.263.52PUMP, WATER, CENTRIFUGAL, TRASH, ENGINE DRIVE, 4" DIA, 705 GPM @ 106' HEAD (ADD HOSES)

HP D-off

33PT 6LTP50WC004 $17,088 1.69 0.33 4.50 251.189.73PUMP, WATER, CENTRIFUGAL, TRASH, ENGINE DRIVE, 6" DIA, 1,300 GPM @ 100' HEAD ,TRAILER MTD (ADD HOSES)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-174


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT


606'' DIESELP50XX001 $24,032 2.40 0.46 8.18 221.6615.86PUMP, WATER, CENTRIFUGAL, TRASH, ENGINE DRIVE, 6" DIA, 1,165 GPM, AIR COOLED (ADD HOSES)

HP D-off

708'' DIESELP50XX002 $44,382 4.44 0.85 9.54 353.0722.71PUMP, WATER, CENTRIFUGAL, TRASH, ENGINE DRIVE, 8" DIA, 2,085 GPM, WATER COOLED (ADD HOSES)

HP D-off

8510'' DIESELP50XX003 $47,606 4.76 0.91 11.59 433.2925.96PUMP, WATER, CENTRIFUGAL, TRASH, ENGINE DRIVE, 10" DIA, 2,665 GPM, WATER COOLED (ADD HOSES)

HP D-off

0.31 HOSES, PUMP, SUCTION & DISCHARGESUBCATEGORY

GORMAN-RUPP COMPANY

P50GR001 $205 0.05 0.00 0.00 10.030.14PUMP, WATER, CENTRIFUGAL, TRASH, HOSE, SUCTION/DISCH, 2" DIA X 20' WITH COUPLING (PER SECTION)



P50GR004 $1,118 0.25 0.02 0.00 10.150.79PUMP, WATER, CENTRIFUGAL, TRASH, HOSE, SUCTION/DISCH, 6" DIA X 20' WITH COUPLING (PER SECTION)


EP 1110-1-8, Vol. 130 Nov 09

2-175


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

P50 GORMAN-RUPP COMPANY (continued)P50GR006 $709 0.16 0.01 0.00 10.090.50PUMP, WATER, CENTRIFUGAL, TRASH,

HOSE, SUCTION/DISCH, 3" DIA X 50' WITH COUPLING (PER SECTION)



PUMPS, WATER, SUBMERSIBLEP550.01 ENGINE DRIVESUBCATEGORY

GRIFFIN DEWATERING CORP.

214MHP55GF001 $20,883 2.09 0.40 2.86 191.459.09PUMP, WATER, SUBMERSIBLE, ENGINE DRIVE, 4" DIA, 400 GPM @ 20' HEAD, SKID MTD (INCLUDES POWER UNIT MODEL 250)(ADD HOSES)

HP D-off

726TP55GF002 $23,212 2.32 0.44 9.81 311.6017.92PUMP, WATER, SUBMERSIBLE, ENGINE DRIVE, 6" DIA, 2,000 GPM @ 20' HEAD, SKID MTD (INCLUDES POWER UNIT MODEL 400)(ADD HOSES)

HP D-off

0.02 ELECTRIC DRIVESUBCATEGORY

GORMAN-RUPP COMPANY

2S2A1P55GR001 $3,833 0.41 0.07 0.26 20.281.24PUMP, WATER, SUBMERSIBLE, ELECTRIC, 2" DIA, 138 GPM @ 20' HEAD (ADD HOSES)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-176


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

P55 GORMAN-RUPP COMPANY (continued)5S3A1P55GR002 $4,739 0.50 0.09 0.64 30.342.01PUMP, WATER, SUBMERSIBLE, ELECTRIC,

3" DIA, 278 GPM @ 20' HEAD (ADD HOSES)

HP E

25S4A1P55GR003 $15,105 1.60 0.28 3.20 121.088.19PUMP, WATER, SUBMERSIBLE, ELECTRIC, 4" DIA, 860 GPM @ 40' HEAD (ADD HOSES)

HP E

60S6A1P55GR004 $22,703 2.41 0.42 7.67 141.6316.70PUMP, WATER, SUBMERSIBLE, ELECTRIC, 6" DIA, 1,950 GPM @ 40' HEAD (ADD HOSES)

HP E

WACKER CORPORATION

1PS2 500P55WC001 $394 0.04 0.01 0.13 10.030.29PUMP, WATER, SUBMERSIBLE, ELECTRIC, 2" DIA, 66 GPM @ 39' HEAD (ADD HOSES)

HP E

1PS2 750P55WC002 $536 0.06 0.01 0.13 10.040.32PUMP, WATER, SUBMERSIBLE, ELECTRIC, 2" DIA, 100 GPM @ 52' HEAD (ADD HOSES)

HP E

PUMPS, WATER, CENTRIFUGAL, DEWATERINGP600.11 SKID MOUNTED, ENGINE DRIVESUBCATEGORY

RIVERSIDE PUMP MANUFACTURING

4S2BP60HO002 $920 0.09 0.02 0.85 10.071.22PUMP, WATER, CENTRIFUGAL, DEWATERING, SKID MOUNTED, ENGINE DRIVE, 2" DIA, 150 GPM @ 22' HEAD (ADD HOSES)

HP G

8TP3BP60HO003 $1,643 0.16 0.03 1.95 10.112.67PUMP, WATER, CENTRIFUGAL, DEWATERING, SKID MOUNTED, ENGINE DRIVE, 3" DIA, 293 GPM @ 20' HEAD (ADD HOSES)

HP G

EP 1110-1-8, Vol. 130 Nov 09

2-177


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

WACKER CORPORATION

4PG 2AP60WC001 $672 0.07 0.01 0.98 10.051.30PUMP, WATER, CENTRIFUGAL, DEWATERING, SKID MOUNTED, ENGINE DRIVE, 2" DIA, 159 GPM @ 98' HEAD (ADD HOSES)

HP G

6PG 3AP60WC002 $887 0.09 0.02 1.46 10.071.91PUMP, WATER, CENTRIFUGAL, DEWATERING, SKID MOUNTED, ENGINE DRIVE, 3" DIA, 264 GPM @ 98' HEAD (ADD HOSES)

HP G

0.21 WHEEL MOUNTED, ENGINE DRIVESUBCATEGORY

GRIFFIN DEWATERING CORP.

21250/4"MHP60GF003 $23,618 2.33 0.45 2.86 191.629.49PUMP, WATER, CENTRIFUGAL, DEWATERING, WHEEL, 4" DIA, 400 GPM @ 60' HEAD (ADD HOSES)

HP D-off

72400/6"TP60GF008 $25,946 2.56 0.50 9.81 311.7818.29PUMP, WATER, CENTRIFUGAL, DEWATERING, WHEEL, 6" DIA, 1,040 GPM @ 60' HEAD (ADD HOSES)

HP D-off


HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-178


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

GORMAN-RUPP COMPANY

4714C2-F3LP60GR001 $24,627 2.43 0.47 6.41 201.6913.93PUMP, WATER, CENTRIFUGAL, DEWATERING, WHEEL, 4" DIA, 600 GPM @ 80' HEAD (ADD HOSES)

HP D-off

10116C2-F4LP60GR002 $28,708 2.84 0.55 24.62 201.9735.78PUMP, WATER, CENTRIFUGAL, DEWATERING, WHEEL, 6" DIA, 1,825 GPM @ 40' HEAD (ADD HOSES)

HP G

PUMPS, WATER, DIAPHRAGMP650.11 SKID MOUNTED, ENGINE DRIVESUBCATEGORY

RIVERSIDE PUMP MANUFACTURING

4DP2BP65HO001 $1,652 0.17 0.03 0.85 10.121.41PUMP, WATER, DIAPHRAGM, SKID MTD, 2" DIA, 33 GPM @ 25' HEAD (ADD HOSES)

HP G

4DP3BP65HO002 $1,919 0.19 0.04 0.85 20.141.48PUMP, WATER, DIAPHRAGM, SKID MTD, 3" DIA, 80 GPM @ 25' HEAD (ADD HOSES)

HP G

0.21 WHEEL MOUNTED, ENGINE DRIVESUBCATEGORY

GORMAN-RUPP COMPANY

53D-13P65GR001 $4,379 0.36 0.08 1.22 20.262.51PUMP, WATER, DIAPHRAGM, WHEEL, 2" DIA SUCTION X 3" DIA DISCHARGE, 56 GPMH @ 25' HEAD (ADD HOSES)

HP G

23D-BP65GR002 $5,153 0.43 0.10 0.37 20.321.71PUMP, WATER, DIAPHRAGM, WHEEL, 3" DIA, 560 GPM @ 25' HEAD (ADD HOSES)

HP G

EP 1110-1-8, Vol. 130 Nov 09

2-179


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

P65 GORMAN-RUPP COMPANY (continued)34D-BP65GR003 $12,355 1.17 0.24 0.73 30.833.87PUMP, WATER, DIAPHRAGM, WHEEL, 4"

DIA, 74 GPM @ 25' HEAD (ADD HOSES)

HP G

WACKER CORPORATION

4PDT 2AP65WC001 $1,738 0.17 0.03 0.98 10.121.54PUMP, WATER, DIAPHRAGM, WHEEL, 2" DIA, 50 GPM @ 25' HEAD (ADD HOSES)

HP G

4PDT 3AP65WC002 $1,880 0.19 0.04 0.98 20.141.59PUMP, WATER, DIAPHRAGM, WHEEL, 3" DIA, 88 GPM @ 25' HEAD (ADD HOSES)

HP G

PUMPS, WATER (For core drills)P700.01 ENGINE DRIVESUBCATEGORY


275-7.6P70XX001 $3,368 0.32 0.07 0.49 10.231.37PUMP, WATER, FOR CORE DRILLS, 7.6 GPM, 75 PSI, MANUAL, SKID (ADD HOSES)

HP G

6225-17.5P70XX002 $8,781 0.82 0.17 1.46 10.583.75PUMP, WATER, FOR CORE DRILLS, 17.5 GPM, 225 PSI, MANUAL, SKID (ADD HOSES)

HP G

EP 1110-1-8, Vol. 130 Nov 09

2-180


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

RIPPERS & HYDRAULIC BANK SLOPERS (Add cost for point wear)R100.00 RIPPERS & HYDRAULIC BANK SLOPERS (Add cost for point wear)SUBCATEGORY


D-5C111R10CA006 $276 0.03 0.01 0.00 10.030.08RIPPER, SHANK, EACH (ADD D-5 TRACTOR DOZER & RIPPER & COST FOR POINT WEAR)

D6RII-174-9198R10CA022 $1,106 0.11 0.02 0.00 20.080.28RIPPER SHANK, EACH (ADD D6RII TRACTOR DOZER & RIPPER & COST FOR POINT WEAR)

D6R II - 9J-8926R10CA023 $1,116 0.11 0.02 0.00 20.080.29RIPPER, SHANK, EACH (ADD D-6 TRACTOR DOZER & RIPPER & COST FOR POINT WEAR)

D-7RR10CA010 $1,809 0.18 0.03 0.00 20.120.46RIPPER, SHANK, EACH (ADD D-7 TRACTOR DOZER & RIPPER & COST FOR POINT WEAR)




D-3R10CA001 $10,502 1.05 0.20 0.00 130.732.79RIPPER, 3-SHANKS & BEAM, HYDRAULIC (ADD D-3 TRACTOR DOZER & COST FOR POINT WEAR)

EP 1110-1-8, Vol. 130 Nov 09

2-181


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

R10 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

D-4C SERIES IIIR10CA003 $10,502 1.05 0.20 0.00 130.732.79RIPPER, 3-SHANKS & BEAM, HYDRAULIC (ADD D-4 TRACTOR DOZER & COST FOR POINT WEAR)

D-5C SERIES IIIR10CA005 $10,502 1.05 0.20 0.00 130.732.79RIPPER, 3-SHANKS & BEAM, HYDRAULIC (ADD D-5 TRACTOR DOZER & COST FOR POINT WEAR)

D-6R IIR10CA007 $24,125 2.41 0.46 0.00 401.676.31RIPPER, 3-SHANKS & BEAM, HYDRAULIC (ADD D-6 TRACTOR DOZER & COST FOR POINT WEAR)

D-7RR10CA009 $44,923 4.49 0.86 0.00 773.1111.69RIPPER, 3-SHANKS & BEAM, HYDRAULIC (ADD D-7 TRACTOR DOZER & COST FOR POINT WEAR)

D-8RR10CA011 $48,826 4.88 0.94 0.00 913.3812.73RIPPER, 1-SHANK & BEAM, HYDRAULIC (ADD D-8 TRACTOR DOZER & RIPPER & COST FOR POINT WEAR)


D-9RR10CA014 $62,798 6.28 1.20 0.00 1024.3416.39RIPPER, 1-SHANK & BEAM, HYDRAULIC (ADD D-9 TRACTOR DOZER & COST FOR POINT WEAR)



EP 1110-1-8, Vol. 130 Nov 09

2-182


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT





ROLLERS, STATIC, TOWED, PNEUMATICR150.00 ROLLERS, STATIC, TOWED, PNEUMATICSUBCATEGORY

SOUTHWEST CONSTRUCTION EQUIPMENT CO.

C-50R15SO001 $133,662 9.68 2.51 0.00 3097.3525.24ROLLER, STATIC, TOWED, PNEUMATIC, 60 TON, 9.8' WIDE, 4 TIRE (ADD TOWING UNIT)

C-75R15SO002 $147,406 9.53 2.76 0.00 3477.5327.42ROLLER, STATIC, TOWED, PNEUMATIC, 75 TON, 10.5' WIDE, 4 TIRE (ADD TOWING UNIT)

C-100XLR15SO003 $205,054 14.15 3.85 0.00 55110.9338.53ROLLER, STATIC, TOWED, PNEUMATIC, 100 TON, 10.5' WIDE, 4 TIRE (ADD TOWING UNIT)

EP 1110-1-8, Vol. 130 Nov 09

2-183


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

ROLLERS, STATIC, TOWED, STEEL DRUMR200.00 ROLLERS, STATIC, TOWED, STEEL DRUMSUBCATEGORY

REYNOLDS INTERNATIONAL, L.P.

DD-48X60R20RI002 $33,607 2.69 0.63 0.00 1771.987.02ROLLER, STATIC, TOWED, 2 STEEL DRUMS, 10-15 TON, 48" WIDE X 60" DIA, PADFOOT (ADD TOWING UNIT)


2DH-RRR20SO001 $74,205 5.94 1.39 0.00 2004.3615.21ROLLER, STATIC, TOWED, 2 STEEL DRUMS, 10-20 TON, 60" WIDE X 60" DIA, SHEEPSFOOT (ADD TOWING UNIT)

ROLLERS, STATIC, SELF-PROPELLED R300.01 PNEUMATICSUBCATEGORY


85BW11RHR30BO004 $86,697 8.47 1.61 10.24 1005.8532.65ROLLER, STATIC, SELF-PROPELLED, PNEUMATIC, 13.50 TON, 68" WIDE, 9 TIRE, ASPHALT COMPACTOR

HP D-off

110BW24RR30BO003 $142,728 14.47 2.65 13.25 2909.8949.22ROLLER, STATIC, SELF-PROPELLED, PNEUMATIC, 30.00 TON, 78" WIDE, 8 TIRE, ASPHALT COMPACTOR

HP D-off


70PS-150BR30CA010 $82,309 8.58 1.53 8.43 855.8229.16ROLLER, STATIC, SELF-PROPELLED, PNEUMATIC, 14.25 TON, 68" WIDE, 9 TIRE, ASPHALT COMPACTOR

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-184


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT



HP D-off


HP D-off


80TRU-PAC 915R30RS003 $64,660 6.61 1.20 9.64 1154.5126.28ROLLER, STATIC, SELF-PROPELLED, PNEUMATIC, 6-15 TON, 68" WIDE, 9 TIRES, ASPHALT/SOIL COMPACTOR

HP D-off

SAKAI AMERICA, INC.

91TS200R30SI002 $107,968 10.94 2.00 10.96 1877.4738.31ROLLER, STATIC, SELF-PROPELLED, PNEUMATIC, 16 TON, 81" WIDE, 9 TIRE, ASPHALT COMPACTOR

HP D-off

95TS600CR30SI003 $133,922 13.69 2.48 11.44 1879.3344.99ROLLER, STATIC, SELF-PROPELLED, PNEUMATIC, 16 TON, 81" WIDE, 9 TIRE, ASPHALT COMPACTOR

HP D-off

108TS650CR30SI004 $177,553 18.39 3.29 13.01 28112.4957.04ROLLER, STATIC, SELF-PROPELLED, PNEUMATIC, 27 TON, 82" WIDE, 7 TIRE, ASPHALT COMPACTOR

HP D-off

0.02 SMOOTH DRUMSUBCATEGORY


47BW5ASR30BO005 $77,396 6.58 1.40 5.66 1304.6922.24ROLLER, STATIC, SELF-PROPELLED, SMOOTH DRUM, DOUBLE DRUM, 6 TON, 40" WIDE ASPHALT COMPACTOR

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-185


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

R30 COMPACTION AMERICA (BOMAG) (continued)


HP D-off


HP D-off


16300 BR30RS001 $14,563 1.24 0.26 3.47 260.886.86ROLLER, STATIC, SELF-PROPELLED, SMOOTH DRUM, DOUBLE DRUM, 1.5 TON, 34" WIDE, ASPHALT COMPACTOR

HP G

40400R30RS002 $29,077 2.47 0.53 4.82 371.7711.36ROLLER, STATIC, SELF-PROPELLED, SMOOTH DRUM, DOUBLE DRUM, 2 TON, 40" WIDE, ASPHALT COMPACTOR

HP D-off

SAKAI AMERICA, INC.

75R2H-2R30SI005 $116,163 9.87 2.11 9.03 2077.0533.98ROLLER, STATIC, SELF-PROPELLED, SMOOTH DRUM, 3 DRUMS, 14 TON, 64" WIDE, ASPHALT COMPACTOR

HP D-off

0.03 TAMPING FOOT, LANDFILL & SOIL COMPACTORSSUBCATEGORY


442BC672RBR30BO009 $592,633 39.51 10.96 53.24 71030.72160.54ROLLER, STATIC, SELF-PROPELLED, LANDFILL/SOIL COMPACTOR, SHEEPSFOOT, 4X4, 35 TON, 63" DIA, 19.58' WIDTH PER 2-PASS, W/BLADE

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-186


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT


442BC772RBR30BO008 $630,416 42.03 11.66 53.24 81232.68167.00ROLLER, STATIC, SELF-PROPELLED, LANDFILL/SOIL COMPACTOR, SHEEPSFOOT, 4X4, 40 TON, 63" DIA, 19.58' WIDTH PER 2-PASS, W/BLADE

HP D-off


240815-FR30CA003 $361,684 24.11 6.69 28.91 44918.7593.98ROLLER, STATIC, SELF-PROPELLED, LANDFILL/SOIL COMPACTOR, SHEEPSFOOT, 4X4, 23 TON, 56" DIA, 14.25' WIDTH PER 2-PASS, W/BLADE

HP D-off

220816-FR30CA012 $368,337 24.56 6.81 26.50 50919.0992.44ROLLER, STATIC, SELF-PROPELLED, LANDFILL/SOIL COMPACTOR, TAMPING FOOT, CHOPPER, 4X4, 25.0 TON, 14.75' WIDTH PER 2-PASS, W/BLADE

HP D-off

315825-G IIR30CA006 $547,931 36.53 10.13 37.94 73428.40135.86ROLLER, STATIC, SELF-PROPELLED, LANDFILL/SOIL COMPACTOR, SHEEPSFOOT, 4X4, 35 TON, 51" DIA, 16.00' WIDTH PER 2-PASS, W/BLADE

HP D-off

315826-G IIR30CA013 $570,225 38.02 10.55 37.94 77129.56139.68ROLLER, STATIC, SELF-PROPELLED, LANDFILL/SOIL COMPACTOR, TAMPING FOOT, CHOPPER, 4X4, 36.5 TON, 15.66' WIDTH PER 2-PASS, W/BLADE

HP D-off

473836 GR30CA009 $758,912 50.59 14.04 56.98 1,16639.34193.10ROLLER, STATIC, SELF-PROPELLED, LANDFILL/SOIL COMPACTOR, TAMPING FOOT, CHOPPER, 4X4, 50.0 TON, 18.58' WIDTH PER 2-PASS, W/BLADE

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-187


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

ROLLERS, VIBRATORY, TOWEDR400.00 ROLLERS, VIBRATORY, TOWEDSUBCATEGORY


50BW6R40BO001 $79,620 7.96 1.53 6.82 1285.5127.58ROLLER, VIBRATORY, TOWED, SINGLE DRUM, SMOOTH, 13,000 LB OPER. WT., 26,550 LB (13.3 TONS) CENTRIFUGAL FORCE, 67'' WIDE (ADD 180 HP TOWING UNIT)

HP D-off

50BW6SR40BO002 $89,013 8.90 1.71 6.82 1486.1629.91ROLLER, VIBRATORY, TOWED, SINGLE DRUM, SHEEPSFOOT, 15,000 LB OPER. WT., 26,550 LB (13.3 TONS) CENTRIFUGAL FORCE, 67'' WIDE (ADD 180 HP TOWING UNIT)

HP D-off

ROLLERS, VIBRATORY, SELF-PROPELLED, DOUBLE DRUMR450.00 ROLLERS, VIBRATORY, SELF-PROPELLED, DOUBLE DRUMSUBCATEGORY


33BW120AD-4R45BO004 $53,903 5.39 1.03 4.50 573.7321.12ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 2.9 TON, 47.2" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

46BW138ADR45BO005 $65,952 6.60 1.26 6.27 924.5626.73ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 4.6 TON, 54.3" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

108BW151AD-4R45BO006 $136,818 13.68 2.62 14.72 1589.4657.43ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 7.8 TON, 66.1" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-188


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT


131BW161AD-4 HFR45BO007 $158,132 15.81 3.03 17.86 20910.9467.34ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 10.4 TON, 66.1" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

205BW190AD-4 HFR45BO008 $164,959 16.50 3.16 27.94 25211.4180.98ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 12.6 TON, 79.0" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off


32CB-214DR45CA001 $46,607 4.66 0.89 4.36 813.2218.80ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 2.5 TON, 39.4" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

32CB-224DR45CA002 $53,316 5.33 1.02 4.36 583.6920.79ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 2.7 TON, 47.2" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

70CB-434CR45CA005 $128,979 12.90 2.47 9.54 1378.9249.14ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 6.6 TON, 56" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

105CB-534CR45CA007 $157,458 15.75 3.02 14.31 23310.9063.06ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 10.0 TON, 67" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

145CB-634DR45CA010 $195,766 19.58 3.75 19.76 28313.5480.67ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 13.2 TON, 84" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off


20300BR45RS001 $18,670 1.87 0.36 2.73 261.308.67ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 2.0 TON, 36" WIDE, ASPHALT COMPACTOR

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-189


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

SAKAI AMERICA, INC.

35SW320-1R45SI008 $36,164 3.62 0.69 4.77 282.5016.19ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 3.0 TON, 47" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

78SW652R45SI009 $98,579 9.86 1.89 10.63 1576.8241.40ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 7.8 TON, 58" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

127SW850-3R45SI010 $132,037 13.20 2.53 17.31 1249.1358.99ROLLER, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM, SMOOTH, 14.0 TON, 79" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE DRUMR500.00 ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE DRUMSUBCATEGORY


50BW124DH-3R50BO005 $66,432 5.72 1.31 4.91 604.1724.39ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 2.9 TON, 47.2" WIDE, 3X2, SOIL COMPACTOR

HP D-off

50BW124PDH-3R50BO010 $68,467 6.29 1.35 4.91 604.5024.57ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, PAD FOOT, 2.9 TON, 47.2" WIDE, 3X2, SOIL COMPACTOR

HP D-off

75BW145D-3R50BO006 $89,943 8.38 1.78 7.37 1105.9733.19ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 5.5 TON, 56.1" WIDE, 3X2, SOIL COMPACTOR

HP D-off


HP D-off

75BW177D-3R50BO007 $124,069 11.48 2.45 7.37 1598.1942.68ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 7.9 TON, 66.4" WIDE, 3X2, SOIL COMPACTOR

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-190


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT



HP D-off


HP D-off


HP D-off


HP D-off


70CS-323CR50CA001 $85,487 7.92 1.69 6.88 975.6531.46ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 4.6 TON, 50" WIDE, 3X2, SOIL COMPACTOR

HP D-off

97CS-431CR50CA003 $115,284 10.64 2.28 9.53 1387.6042.76ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 6.9 TON, 66" WIDE, 3X2, SOIL COMPACTOR

HP D-off

100CS-433ER50CA005 $125,094 11.56 2.47 9.83 1478.2545.79ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 7.1 TON, 66" WIDE, 3X2, SOIL COMPACTOR

HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-191


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)


70CP-323C (PADS)R50CA002 $99,576 9.24 1.97 6.88 1056.5935.33ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, PAD FOOT, 4.6 TON, 50" WIDE, 3X2, SOIL COMPACTOR

HP D-off

150CP-563E (PADS)R50CA010 $189,604 17.30 3.75 14.74 26212.4069.46ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, PAD FOOT, 12.5 TON, 84" WIDE, 3X2 SOIL COMPACTOR

HP D-off

100CP-433E (PADS)R50CA004 $137,930 12.76 2.73 9.83 1509.1149.31ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, PAD FOOT, 7.1 TON, 66" WIDE, 3X2, SOIL COMPACTOR

HP D-off

150CP-563E (PADS)R50CA012 $189,812 17.32 3.75 14.74 27512.4169.51ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, PAD FOOT, 12.5 TON, 84" WIDE, 3X2, SOIL COMPACTOR

HP D-off

INGERSOLL RAND ROAD MACHINERY DIV

80SD-45DR50IP001 $88,393 8.08 1.75 7.86 1045.7933.50ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 4.9 TON, 54" WIDE, SOIL COMPACTOR

HP D-off

SAKAI AMERICA, INC.

28TW350 ComboR50SI024 $56,648 5.19 1.12 2.75 253.7218.82ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 1.5 TON, 39.5" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

30TW500 ComboR50SI025 $69,928 6.44 1.38 2.95 364.6022.69ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 3.9 TON, 51" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

60SV201DR50SI006 $74,606 6.80 1.47 5.90 414.8727.44ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 4.8 TON, 54" WIDE, 3X2, SOIL COMPACTOR

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-192


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

R50 SAKAI AMERICA, INC. (continued)60SV201T (PADS)R50SI007 $79,897 7.30 1.58 5.90 435.2328.90ROLLER, VIBRATORY, SELF-PROPELLED,

SINGLE DRUM, SMOOTH, 4.9 TON, 54" WIDE, 3X2, SOIL COMPACTOR

HP D-off

100SV400D-2R50SI022 $101,967 9.39 2.01 9.83 1566.7139.45ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 7.7 TON, 67" WIDE, 3X2, SOIL COMPACTOR

HP D-off

104TW750 ComboR50SI026 $139,155 12.93 2.75 10.22 1009.2250.04ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 8.7 TON, 66" WIDE, 2X1, ASPHALT COMPACTOR

HP D-off

100SV400TB-2 (PADS)

R50SI023 $114,130 10.53 2.25 9.83 727.5242.79ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 9.6 TON, 67" WIDE, 3X2, SOIL COMPACTOR

HP D-off

148SV510D-3R50SI013 $122,661 10.99 2.42 14.54 5077.9250.89ROLLER, VIBRATORY, SELF-PROPELLED, SINGLE DRUM, SMOOTH, 11.5 TON, 84" WIDE, 3X2, SOIL COMPACTOR

HP D-off

148SV510T-3 (PADS)


HP D-off

148SV510TF-3 (PADS)


HP D-off

ROOFING EQUIPMENTR550.00 ROOFING EQUIPMENTSUBCATEGORY


8EZ LOAD 270R55AE001 $7,781 1.05 0.15 1.30 200.687.24ROOFING EQUIPMENT, KETTLE, 270 GAL, W/PUMP, TRAILER MTD

HP G

EP 1110-1-8, Vol. 130 Nov 09

2-193


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

R55 AEROIL PRODUCTS COMPANY, INC. (continued)


HP G


HP G

8EZ LOAD 1000R55AE004 $16,931 2.22 0.33 1.30 541.4413.83ROOFING EQUIPMENT, KETTLE, 1,000 GAL, W/PUMP, TRAILER MTD

HP G

8RHINO S PEELER

R55AE008 $5,562 0.75 0.11 1.30 60.493.25ROOFING EQUIPMENT, ROOF PEELER, 16" WIDE, WALK BEHIND, POWERED WHEEL 2X2

HP G

9MKI9R55AE009 $2,017 0.29 0.04 1.46 20.192.29ROOFING EQUIPMENT, 1-BLADE CUTTER, 3.75" DEEP, WALK BEHIND (ADD BLADE COST)

HP G

16MK216RR55AE010 $3,702 0.52 0.07 2.60 30.334.10ROOFING EQUIPMENT, 2-BLADE CUTTER, 20'' WIDE, 3.75" DEEP, WALK BEHIND (ADD BLADE COST)

HP G

5BUFFALO 800R55AE011 $3,792 0.45 0.07 0.81 40.302.09ROOFING EQUIPMENT, MATERIAL BUGGY, 36'' WIDE, WALK BEHIND GRAVEL SPREADER, HOPPER 800 LBS, 8 CF, 4X2

HP G

GARLOCK EQUIPMENT CO.

5SUPER MINI SAW

R55GL017 $2,059 0.29 0.04 0.81 20.191.57ROOFING EQUIPMENT, 1-BLADE CUTTER, 18" HEIGHT & 2" WALL CLEARANCE

HP G

9DUST MASTER ULTRA CU

R55GL016 $5,811 0.82 0.11 1.46 30.523.52ROOFING EQUIPMENT, 1-BLADE CUTTER, W/WATER DAMPENING SYSTEM AND H.E.P.A. VACUUM SYSTEM

HP G

16ENFORCER TWIN CUTTER

R55GL011 $6,201 0.88 0.12 2.60 40.564.92ROOFING EQUIPMENT, 2-BLADE CUTTER, 30" WIDE, SELF PROPELLED (ADD BLADE COST)

HP G

EP 1110-1-8, Vol. 130 Nov 09

2-194


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

R55 GARLOCK EQUIPMENT CO. (continued)5NO.12R55GL018 $2,134 0.30 0.04 0.81 10.191.59ROOFING EQUIPMENT, SCRATCHER, 4.5"

WIDE HP G

8NO. 30R55GL019 $4,132 0.59 0.08 1.30 30.382.80ROOFING EQUIPMENT, SCRATCHER, 13" WIDE

HP G

11 ROTARY PLANER

R55GL009 $2,539 0.36 0.05 1.71 20.232.73ROOFING EQUIPMENT, ROTARY PLANER, 12" WIDE

HP G

11ROCK MASTER SWEEPER

R55GL008 $5,379 0.68 0.10 1.79 20.443.70ROOFING EQUIPMENT, POWER SWEEPER, 48" WIDE

HP G

9MODEL 1000R55GL015 $10,443 1.48 0.20 1.46 80.945.03ROOFING EQUIPMENT, HYDRAULIC HOIST, W/175' CABLE, 1,000 LB CAP

HP G

18SUPER MAX HYDR HOIST

R55GL007 $12,748 1.81 0.25 2.93 101.167.42ROOFING EQUIPMENT, HYDRAULIC SWING HOIST, W/275' CABLE, 1,400 LB CAP

HP G

MODEL 30R55GL013 $1,421 0.11 0.03 0.00 30.090.65ROOFING EQUIPMENT, KETTLE, 30 GAL, WHEEL MTD

MODEL 90R55GL014 $3,233 0.46 0.06 0.00 70.291.40ROOFING EQUIPMENT, KETTLE, 90 GAL, SKID MTD

MODEL 115 R55GL001 $3,724 0.50 0.07 0.00 80.321.70ROOFING EQUIPMENT, KETTLE, 115 GAL, TRAILER MTD

5MODEL 175 R55GL002 $7,270 0.98 0.14 0.81 170.633.73ROOFING EQUIPMENT, KETTLE, 175 GAL, W/PUMP, TRAILER MTD

HP G

9MODEL 300R55GL012 $11,481 1.58 0.22 1.46 231.016.08ROOFING EQUIPMENT, KETTLE, 300 GAL, W/PUMP, TRAILER MTD

HP G


HP G


HP G

EP 1110-1-8, Vol. 130 Nov 09

2-195


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

SCRAPERS, ELEVATINGS100.01 0 THRU 200 HPSUBCATEGORY


175613-C SERIES IIS10CA001 $276,648 21.52 5.19 17.20 33615.9580.08SCRAPER, ELEVATING LOADING, 11 CY, 13 TON, 7.7' CUT WIDTH, 4X2 - SINGLE POWERED

HP D-off

0.02 OVER 200 HPSUBCATEGORY


265615-C SERIES IIS10CA002 $427,446 22.78 8.14 26.04 52619.53111.14SCRAPER, ELEVATING LOADING, 17 CY, 19 TON, 9.5' CUT WIDTH, 4X2 - SINGLE POWERED

HP D-off

365623-GS10CA003 $638,634 35.31 12.16 35.87 81029.82155.71SCRAPER, ELEVATING LOADING, 23 CY, 25 TON, 11.5' CUT WIDTH, 4X2 - SINGLE POWERED

HP D-off

SCRAPERS, CONVENTIONALS150.00 SCRAPERS, CONVENTIONALSUBCATEGORY


365621-GS15CA001 $556,906 28.37 10.16 33.55 71424.35123.81SCRAPER, CONVENTIONAL, STANDARD LOADING, 21 CY, 24 TON, 9.1' CUT WIDTH, 4X2 - SINGLE POWERED

HP D-off

450631-GS15CA002 $845,740 43.26 15.42 41.37 1,02037.05175.79SCRAPER, CONVENTIONAL, STANDARD LOADING, 34 CY, 37.5 TON, 11.5' CUT WIDTH, 4X2 - SINGLE POWERED

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-196


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

S15 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

550651-ES15CA003 $1,048,814 53.87 19.13 50.56 1,32346.07215.63SCRAPER, CONVENTIONAL, STANDARD LOADING, 44 CY, 52 TON, 12.6' CUT WIDTH, 4X2 - SINGLE POWERED

HP D-off

ATI-Bell

4224206DTIS28S15JU001 $562,598 29.46 10.26 38.79 94024.99123.62SCRAPER, CONVENTIONAL, STANDARD LOADING, 28 CY, 32 TON, 14' CUT WIDTH, 4X4 - SINGLE POWERED, TRACTOR EQUIPPED WITH ATI RUBBER TRACKS

HP D-off

4224206DTIS33S15JU002 $582,173 30.51 10.62 38.79 95325.88126.31SCRAPER, CONVENTIONAL, STANDARD LOADING, 33 CY, 37 TON, 14' CUT WIDTH, 4X4 - SINGLE POWERED, TRACTOR EQUIPPED WITH ATI RUBBER TRACKS

HP D-off

SCRAPERS, TANDEM POWEREDS200.00 SCRAPERS, TANDEM POWEREDSUBCATEGORY


330627-GS20CA001 $632,445 32.40 11.53 52.78 79127.73160.31225 HP D-offSCRAPER, TANDEM POWERED, STANDARD LOADING, 21 CY, 24 TON, 9.1' CUT WIDTH, 4X4, D-9 ASSISTED LOADING

HP D-off

330627-G PPS20CA002 $668,014 34.29 12.18 52.78 82429.33165.32225 HP D-offSCRAPER, TANDEM POWERED, STANDARD LOADING, 20 CY, 24 TON, 9.1' CUT WIDTH, 4X4, PUSH-PULL

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-197


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

S20 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

450637-GS20CA003 $1,069,746 55.20 19.51 66.58 1,08447.11242.05250 HP D-offSCRAPER, TANDEM POWERED, STANDARD LOADING, 34 CY, 37.5 TON, 11.5' CUT WIDTH, 4X4, D-10 ASSISTED LOADING

HP D-off

450637-G PPS20CA004 $1,113,627 57.54 20.31 66.58 1,11749.08248.23250 HP D-offSCRAPER, TANDEM POWERED, STANDARD LOADING, 34 CY, 37.5 TON, 11.5' CUT WIDTH, 4X4, PUSH-PULL

HP D-off

550657-ES20CA005 $1,267,189 64.05 23.11 90.35 1,51655.14311.57400 HP D-offSCRAPER, TANDEM POWERED, STANDARD LOADING, 44 CY, 52 TON, 12.6' CUT WIDTH, 4X4, D-11 ASSISTED LOADING

HP D-off

550657-E PPS20CA006 $1,393,761 72.27 25.42 90.35 1,55061.56316.35400 HP D-offSCRAPER, TANDEM POWERED, STANDARD LOADING, 44 CY, 52 TON, 12.6' CUT WIDTH, 4X4, PUSH-PULL

HP D-off

SCRAPERS, TRACTOR DRAWNS250.00 SCRAPERS, TRACTOR DRAWNSUBCATEGORY

DEERE & COMPANY

1510CS25JD001 $53,127 3.23 0.98 0.00 1682.6010.63SCRAPER, TOWED, STANDARD LOADING, 11 CY, 17 TON, 10' CUT WIDTH (ADD 225 HP TRACTOR)

1814CS25JD002 $66,524 3.97 1.23 0.00 2133.2213.14SCRAPER, TOWED, STANDARD LOADING, 14 CY, 23 TON, 14' CUT WIDTH (ADD 360HP TRACTOR)

EP 1110-1-8, Vol. 130 Nov 09

2-198


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

REYNOLDS INTERNATIONAL, L.P.

14CS10S25RI001 $43,845 2.82 0.81 0.00 1382.228.61SCRAPER, TOWED, PIVOT DUMP, 10.7-14 CY, 15 TON, 10' CUT WIDTH (ADD 250 - 300 HP TRACTOR)

17C12 (RG)S25RI002 $49,413 3.15 0.91 0.00 1702.499.63SCRAPER, TOWED, PIVOT DUMP, 13-17 CY, 17 TON, 12' CUT WIDTH (ADD 350 - 400 HP TRACTOR)

ROME PLOW CO.

R56HS25RM003 $93,316 5.41 1.73 0.00 2034.4419.06SCRAPER, TOWED, 9-12 CY, 12.5 TON, 8.5' CUT WIDTH (ADD 120-165 HP TRACTOR)

R67H S25RM001 $123,645 7.43 2.29 0.00 2386.0123.81SCRAPER, TOWED, 12-17 CY, 17 TON, 9.9' CUT WIDTH (ADD 165-215 HP TRACTOR)

R89HS25RM002 $182,457 10.79 3.37 0.00 3828.7734.84SCRAPER, TOWED, 18-26 CY, 25 TON, 10.8' CUT WIDTH (ADD 285-370 HP TRACTOR)

SCREENING & CRUSHING PLANTSS300.10 CONVEYORSSUBCATEGORY


1512-3050S30KB034 $54,865 4.63 0.96 1.38 153.2812.79SCREENING & CRUSHING PLANTS, FEEDER CONVEYOR, 30" WIDE X 50' LONG, 7 CY HOPPER & 6' FEED, PORTABLE, 500 TPH

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-199


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

S30 KOLBERG - PIONEER, INC (continued)2012-3070S30KB035 $62,569 5.27 1.10 1.85 183.7415.01SCREENING & CRUSHING PLANTS,

FEEDER CONVEYOR, 30" WIDE X 70' LONG, 7 CY HOPPER & 6' FEED, PORTABLE, 500 TPH

HP E


HP E


HP E

1013-2480S30KB001 $36,149 3.02 0.63 0.92 142.148.42SCREENING & CRUSHING PLANTS, CONVEYOR, STACKING, 24" WIDE X 80' LONG, PORTABLE, 250 TPH

HP E


HP E


HP E


HP E


HP E


HP E

EP 1110-1-8, Vol. 130 Nov 09

2-200


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT


CONVEYOR, SIDE FOLDING STACKER, 24" WIDE X 80' LONG, WHEEL MTD, 750 TPH

HP E

1531-24100S30KB008 $51,099 4.35 0.90 1.38 273.0812.05SCREENING & CRUSHING PLANTS, CONVEYOR, SIDE FOLDING STACKER, 24" WIDE X 100' LONG, PORTABLE, 250 TPH

HP E


HP E


HP E


HP E


HP E


HP E

EP 1110-1-8, Vol. 130 Nov 09

2-201


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)


CONVEYOR, SIDE FOLDING STACKER, 36" WIDE X 100' LONG, PORTABLE, 750 TPH

HP E


HP E

2535-24150S30KB018 $104,411 9.06 1.83 2.31 396.3623.81SCREENING & CRUSHING PLANTS, CONVEYOR, FIXED HEIGHT STACKER, 24" WIDE X 150' LONG, PORTABLE, 750 TPH

HP E

4035-30150S30KB021 $121,025 10.52 2.12 3.69 567.3829.17SCREENING & CRUSHING PLANTS, CONVEYOR, FIXED HEIGHT STACKER, 30" WIDE X 150' LONG, PORTABLE, 1,500 TPH

HP E

6035-36150S30KB024 $138,715 12.07 2.43 5.54 848.4735.45SCREENING & CRUSHING PLANTS, CONVEYOR, FIXED HEIGHT STACKER, 36" WIDE X 150' LONG, PORTABLE, 2,000 TPH

HP E

2036-24100S30KB025 $74,400 6.41 1.30 1.85 524.5117.28SCREENING & CRUSHING PLANTS, CONVEYOR, ADJUSTABLE HEIGHT RADIAL STACKER, 24" WIDE X 100' LONG, PORTABLE, 750 TPH

HP E

2036-24125S30KB026 $88,406 7.65 1.55 1.85 575.3820.02SCREENING & CRUSHING PLANTS, CONVEYOR, ADJUSTABLE HEIGHT RADIAL STACKER, 24" WIDE X 120' LONG, PORTABLE, 750 TPH

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-202


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT


CONVEYOR, ADJUSTABLE HEIGHT RADIAL STACKER, 24" WIDE X 150' LONG, PORTABLE, 750 TPH

HP E

3036-30100S30KB028 $84,609 7.31 1.48 2.77 645.1420.69SCREENING & CRUSHING PLANTS, CONVEYOR, ADJUSTABLE HEIGHT RADIAL STACKER, 30" WIDE X 100' LONG, PORTABLE, 1,500 TPH

HP E


HP E


HP E


HP E


HP E


HP E

EP 1110-1-8, Vol. 130 Nov 09

2-203


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

S30 KOLBERG - PIONEER, INC (continued)301430-60-25S30KB042 $92,984 8.09 1.63 2.77 185.6822.31SCREENING & CRUSHING PLANTS,

SURGE BIN, 25CY, BELT FEEDER, & 30" WIDE X 60' LONG CONVEYOR, PORTABLE, 1,500 TPH

HP E

151936-2S30KB054 $95,173 8.28 1.67 1.38 185.8120.60SCREENING & CRUSHING PLANTS, SURGE BIN, 25CY, BELT FEEDER, & 30" WIDE X 40' LONG CONVEYOR, PORTABLE, 1,500 TPH

HP E

401436-60-25S30KB053 $96,068 8.34 1.68 3.69 205.8524.32SCREENING & CRUSHING PLANTS, SURGE BIN, 25CY, BELT FEEDER, & 36" WIDE X 60' LONG CONVEYOR, PORTABLE, 2,000 TPH

HP E


HP E


HP E

PUTZMEISTER INC.

215TELEBELT TB 50

S30PU001 $248,047 22.06 4.35 21.13 20115.3872.19SCREENING & CRUSHING PLANTS, CONVEYOR, 16" WIDE X 50' LONG, 1 CY HOPPER & TREMIE, 2X4, TRUCK MTD, 80 CY/HR

HP D-off

350TELEBELT TB 80

S30PU002 $482,567 42.99 8.46 34.39 33229.96132.84SCREENING & CRUSHING PLANTS, CONVEYOR, 18" WIDE X 80' LONG, 3 CY HOPPER & TREMIE, 4X6, TRUCK MTD, 360 CY/HR

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-204


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

S30 PUTZMEISTER INC. (continued)350TELEBELT TB

110S30PU003 $624,263 55.69 10.94 34.39 59238.79160.31SCREENING & CRUSHING PLANTS,

CONVEYOR, 18" WIDE X 106' LONG, 3 CY HOPPER & TREMIE, 4X8, TRUCK MTD, 360 CY/HR

HP D-off

TELSMITH INC.

12PTC 24IN X 50FT

S30TS001 $37,833 3.22 0.66 1.11 102.279.06SCREENING & CRUSHING PLANTS, CONVEYOR, TRUSS FRAME, 24" WIDE X 50' LONG, WHEEL MTD, 300 TPH

HP E

17PTC 24IN X 70FT


HP E

17PTC 30IN X 50FT


HP E

22PTC 30IN X 70FT

S30TS004 $53,081 4.51 0.93 2.03 173.1913.44SCREENING & CRUSHING PLANTS, CONVEYOR, TRUSS FRAME, 30" WIDE X 70' LONG, WHEEL MTD, 1,000 TPH

HP E

22PTC 36IN X 50FT


HP E

27PTC 36IN X 70FT


HP E

32PTC 42IN X 50FT


HP E

42PTC 42IN X 70FT


HP E

EP 1110-1-8, Vol. 130 Nov 09

2-205


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

0.20 CRUSHERS - VERTICAL & HORIZONTAL SHAFT IMPACTORSUBCATEGORY

HEWITT-ROBINS

250MODEL 13654VS30HW001 $329,236 11.58 5.42 23.08 80411.2169.61SCREENING & CRUSHING PLANTS, CRUSHER - SHAFT IMPACTOR, 36"X54", SINGLE ROTOR, 250 TPH, W/3' X 16' FEEDER/ 4' GRIZZLY/ 24" X 8' REJECTION CONVEYOR/ & 36" X 37' DISCHARGE END DELIVERY CONVEYOR, TRAILER MTD (ADD 250 KW GENERATOR)

HP E

350MODEL 14866VS30HW002 $444,660 15.69 7.32 32.31 1,28015.1795.71SCREENING & CRUSHING PLANTS, CRUSHER - SHAFT IMPACTOR, 48"X66" SINGLE ROTOR, 350 TPH, W/4'X16' FEEDER/ 6' GRIZZLY/ 30" X 9.5' REJECTION CONVEYOR/ & 48" X43' DISCHARGE END DELIVERY CONVEYOR, TRAILER MTD (ADD 350 KW GENERATOR)

HP E

450MODEL H4832SS30HW013 $393,642 13.91 6.48 41.54 60013.44104.49SCREENING & CRUSHING PLANTS, CRUSHER - SHAFT IMPACTOR, SECONDARY, 48"X32" HAMMERMILL, 500 TPH, W/3' X 37' FEED CONVEYOR/ 5' X 16' VIBRATORY HORIZONTAL TRIPLE DECK SCREEN/ 36"X30' RETURN CONVEYOR/ & ROTOR LIFT, TRAILER MTD (ADD 450 KW GENERATOR)

HP E


360CS-4250S30KB045 $562,705 20.05 9.26 35.38 54819.2997.90SCREENING & CRUSHING PLANTS, CRUSHER - SHAFT IMPACTOR, 42" X 52", 500 TPH, W/18' X 42" VIBRATORY FEEDER/ ADJUSTABLE GRIZZLY/ & BYPASS FEED, TRAILER MTD

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-206


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

TELSMITH INC.

3004246S30TS009 $297,363 10.71 4.89 27.69 59510.2575.76SCREENING & CRUSHING PLANTS, CRUSHER - SHAFT IMPACTOR, 46'' X 59'', 600 TPH

HP E

4004856S30TS010 $440,888 15.87 7.26 36.92 94215.20105.53SCREENING & CRUSHING PLANTS, CRUSHER - SHAFT IMPACTOR, 56'' X 85'', 1,100 TPH

HP E

8006071S30TS011 $731,876 26.35 12.05 73.84 1,95025.23195.82SCREENING & CRUSHING PLANTS, CRUSHER - SHAFT IMPACTOR, 71'' X 100'', 2,100 TPH

HP E

0.21 CRUSHERS - CONESUBCATEGORY


2721200 LSS30KB046 $393,740 13.93 6.48 25.11 81013.4583.08SCREENING & CRUSHING PLANTS, CRUSHERS - CONE, SECONDARY, 120 TPH @ 3/8" -> 250 TPH @ 1", 42" X 50" IMPACT CRUSHER, W/HOPPER/ & 36" X 32' END DELIVERY CONVEYOR, TRAILER MTD (ADD 210KW GENERATOR)

HP E

3151400 LSS30KB047 $490,109 17.46 8.07 29.07 74116.8099.79SCREENING & CRUSHING PLANTS, CRUSHERS - CONE, SECONDARY PLANT, 630 TPH @ 1" ->1,050 TPH @ 2.5", 42" X 50" IMPACT CRUSHER, W/HOPPER/ & 42" X 32' END DELIVERY CONVEYOR, TRAILER MTD (INCLUDES GENERATOR)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-207


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

0.22 CRUSHERS - JAWSUBCATEGORY

HEWITT-ROBINS

40MODEL J1524PFS30HW005 $176,993 6.21 2.91 3.69 866.0221.10SCREENING & CRUSHING PLANTS, JAW CRUSHER, 15"X24", 21 TPH @ 1" -> 54 TPH @ 3", W/2.5' X 8' FEEDER/ 2' GRIZZLY/ & 24" X 20' END DELIVERY CONVEYOR, TRAILER MTD (ADD 40 KW GENERATOR)

HP E

100MODEL J1536VS30HW006 $294,593 10.43 4.85 9.23 12810.0739.58SCREENING & CRUSHING PLANTS, JAW CRUSHER, 15"X36", 45 TPH @1.5" -> 150 TPH @ 6", W/3' X 14' FEEDER/ 4' GRIZZLY/ & 30" X 31' END DELIVERY CONVEYOR, TRAILER MTD (ADD 40 KW GENERATOR)

HP E

125MODEL J2036VS30HW007 $320,108 11.35 5.27 11.54 12810.9545.29SCREENING & CRUSHING PLANTS, JAW CRUSHER, 20" X 36", 65 TPH @ 2" -> 223 TPH @ 7", W/3' X 14' FEEDER/ 4' GRIZZLY/ & 30" X 31' END DELIVERY CONVEYOR, TRAILER MTD (ADD 40 KW GENERATOR)

HP E

150MODEL J2142VS30HW009 $346,886 12.23 5.71 13.85 15211.8351.34SCREENING & CRUSHING PLANTS, JAW CRUSHER, 21" X 42", 183 TPH @ 4" -> 345 TPH @ 8", W/3.5' X 16' FEEDER/ 4' GRIZZLY/ & 36" X 34' END DELIVERY CONVEYOR, TRAILER MTD (ADD 40 KW GENERATOR)

HP E

200MODEL J2248VS30HW011 $414,404 14.63 6.82 18.46 16814.1464.24SCREENING & CRUSHING PLANTS, JAW CRUSHER, 22" X 48", 115 TPH @ 2.5" -> 240 TPH @ 6", W/4' X 16' FEEDER/ 4' GRIZZLY/ & 48" X 37' END DELIVERY CONVEYOR (ADD 40 KW GENERATOR)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-208


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

S30 HEWITT-ROBINS (continued)125MODEL J2436VS30HW008 $334,430 11.87 5.50 11.54 12811.4446.50SCREENING & CRUSHING PLANTS, JAW

CRUSHER, 24" X 36", 95 TPH @ 2.5" -> 230 TPH @ 6", W/3' X 14' FEEDER/ 4' GRIZZLY/ & 30" X 31' END DELIVERY CONVEYOR, TRAILER MTD (ADD 40 KW GENERATOR)

HP E

200MODEL J3042VS30HW010 $422,628 14.93 6.96 18.46 15614.4364.89SCREENING & CRUSHING PLANTS, JAW CRUSHER, 30" X 42", 200 TPH @ 4" -> 390 TPH @ 8", W/3.5' X 16' FEEDER/ 6' GRIZZLY/ & 36" X 55' END DELIVERY CONVEYOR, TRAILER MTD (ADD 40 KW GENERATOR)

HP E

200MODEL J3048VS30HW012 $489,710 17.31 8.06 18.46 16816.7270.72SCREENING & CRUSHING PLANTS, JAW CRUSHER, 30" X 48", 340 TPH @ 5" -> 615 TPH @ 10", W/4' X 16' FEEDER/ 4' GRIZZLY/ & 48" X 37' END DELIVERY CONVEYOR, TRAILER MTD (ADD 40 KW GENERATOR)

HP E


245CS-1536S30KB055 $365,554 12.99 6.02 24.08 54812.5258.71SCREENING & CRUSHING PLANTS, JAW CRUSHER, 15" X 36", 45 TPH @ 1.5" -> 150 TPH @ 6", W/36"' X 14' VIBRATING FEEDER/ ADJUSTABLE GRIZZLY & BYPASS/ HOPPER/ & 36" X 22' END DELIVERY CONVEYOR, TRAILER MTD, INCLUDES GENERATOR

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-209


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

S30 KOLBERG - PIONEER, INC (continued)1301524-2416

DUPLEX PLS30KB058 $391,671 13.95 6.45 12.00 39113.4352.02SCREENING & CRUSHING PLANTS, JAW

CRUSHER, 15" X 36", 200 TPH @ 1/4" -> 250 TPH @ 6", W/36" X 14' VIBRATING FEEDER/ ADJUSTABLE GRIZZLY & BYPASS/ HOPPER/ SCREEN CONVEYOR/ & TRIPLE VIBRATORY SCREENS, TRAILER MTD

HP E

245CS-2036S30KB056 $374,638 13.31 6.17 24.08 59012.8359.47SCREENING & CRUSHING PLANTS, JAW CRUSHER, 20" X 36", 65 TPH @ 2" -> 223 TPH @ 7", W/36"' X 14' VIBRATING FEEDER/ ADJUSTABLE GRIZZLY & BYPASS/ HOPPER/ & 36" X 22' END DELIVERY CONVEYOR, TRAILER MTD, INCLUDES GENERATOR

HP D-off

3002036-3024 DUPLEX PL

S30KB059 $614,066 21.88 10.11 27.69 41521.0595.10SCREENING & CRUSHING PLANTS, JAW CRUSHER, 20" X 36", 270 TPH @ 1/4" -> 320 TPH @ 7", W/36" X 14' RECIPROCATING PLATE FEEDER/ 12' LONG ADJUSTABLE GRIZZLY & BYPASS/ HOPPER/ & 18" X 15' SCREEN CONVEYOR, TRAILER MTD (ADD 300KW GENERATOR)

HP E

245CS-2436S30KB057 $418,116 14.88 6.88 24.08 70114.3263.14SCREENING & CRUSHING PLANTS, JAW CRUSHER, 24" X 36", 95 TPH @ 2.5" -> 230 TPH @ 6", W/36"' X 16' VIBRATING FEEDER/ ADJUSTABLE GRIZZLY & BYPASS/ HOPPER/ & 36" X 22' END DELIVERY CONVEYOR, TRAILER MTD, INCLUDES GENERATOR

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-210


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

0.30 SCREENING PLANTSUBCATEGORY

HEWITT-ROBINS

15V-11 6X16FT, DD

S30HW014 $128,638 11.32 2.25 1.38 1017.9128.62SCREENING & CRUSHING PLANTS, SCREENING PLANT, 6' X 16' VIBRATORY SLOPE DOUBLE DECK SCREENS, W/36" X 16.5' UNDER SCREEN CONVEYOR/ 7 CY HOPPER/ & FEEDER, TRAILER MTD

HP E

20V-11 6X20FT, DD

S30HW016 $133,801 11.79 2.34 1.85 1158.2430.41SCREENING & CRUSHING PLANTS, SCREENING PLANT, 6' X 20' VIBRATORY SLOPE DOUBLE DECK SCREENS, W/36" X 16.5' UNDER SCREEN CONVEYOR/ 7 CY HOPPER/ & FEEDER, TRAILER MTD

HP E

25V-11 6X16FT, TDS30HW015 $141,369 12.47 2.48 2.31 1388.7232.68SCREENING & CRUSHING PLANTS, SCREENING PLANT, 6' X 16' VIBRATORY SLOPE TRIPLE DECK SCREENS W/36" X 16.5' UNDER SCREEN CONVEYOR/ 7 CY HOPPER/ & FEEDER, TRAILER MTD

HP E

25V-11 6X20FT, TDS30HW017 $143,903 12.70 2.52 2.31 1678.8733.20SCREENING & CRUSHING PLANTS, SCREENING PLANT, 6' X 20' VIBRATORY SLOPE TRIPLE DECK SCREENS W/36" X 16.5' UNDER SCREEN CONVEYOR/ 7 CY HOPPER/ & FEEDER, TRAILER MTD,

HP E

40V-11 8X20FT, TDS30HW018 $171,430 14.95 3.00 3.69 24310.4840.99SCREENING & CRUSHING PLANTS, SCREENING PLANT, 8' X 20' VIBRATORY SLOPE TRIPLE DECK SCREENS, W/48" X 15.5' UNDER SCREEN CONVEYOR/ 7 CY HOPPER/ & FEEDER, TRAILER MTD

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-211


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)


85616 E-3S30KB048 $173,669 15.28 3.04 7.85 28010.6847.85SCREENING & CRUSHING PLANTS, SCREENING PLANT, 6' X 16', VIBRATORY SLOPE TRIPLE DECK SCREENS, W/HOPPER/ 36" X 28.5' FEEDER CONVEYOR/ 48" X27' UNDER SCREEN CONVEYOR/ & 24" X 20' SIDE DELIVERY CONVEYOR, TRAILER MTD

HP E

90620 E-3S30KB049 $204,744 17.26 3.59 8.31 35512.2255.05SCREENING & CRUSHING PLANTS, SCREENING PLANT, 6' X 20' VIBRATORY SLOPE TRIPLE DECK SCREENS, W/HOPPER/ 42" X 34' FEEDER CONVEYOR/ 60" X 25' UNDER SCREEN CONVEYOR/ & 30" X 15' SIDE DELIVERY CONVEYOR, TRAILER MTD

HP E

2501822S30KB050 $246,833 21.86 4.32 23.08 41615.2586.27SCREENING & CRUSHING PLANTS, WASHING/SCREENING PLANT, 6' X 16' VIBRATORY SLOPE TRIPLE DECK SCREENS, W/HOPPER / 3 PRODUCT CHUTES/ ONE FINES CHUTE TO 8' X 32' CLASSIFYING TANK/ 36" DIA X 32' SLOPED SCREW & CHUTE, TRAILER MTD (ADD WATER & FEEDER)

HP E

2501830S30KB051 $313,608 27.70 5.49 23.08 42019.34100.02SCREENING & CRUSHING PLANTS, WASHING/SCREENING PLANT, 6' X 20' VIBRATORY SLOPED TRIPLE DECK SCREENS, W/HOPPER/ 3 PRODUCT CHUTES/ ONE FINES CHUTE/ 8' X 32' CLASSIFYING TANK/ & 44" DIA X 32' SLOPED SCREW & CHUTE, TRAILER MTD (ADD WATER & FEEDER)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-212


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

S30 KOLBERG - PIONEER, INC (continued)2507208-32 S/PS30KB052 $327,395 29.29 5.74 23.08 45020.39102.91SCREENING & CRUSHING PLANTS,

CLASSIFYING PLANT (SAND SORT) 8'W X 32'L TANK & 44" DIA SCREW

HP E

METSO MINERALS

25CV 50DS30RA002 $72,638 6.44 1.27 2.46 1304.4917.76SCREENING & CRUSHING PLANTS, GRIZZLY-SINGLE SCREEN, 120 CY/HR, TRAILER MTD

HP D-off

49CV 90DS30RA003 $114,908 10.15 2.01 4.82 1957.0929.13SCREENING & CRUSHING PLANTS, GRIZZLY-SINGLE SCREEN, 200 CY/HR, TRAILER MTD

HP D-off

SNOW REMOVAL EQUIPMENTS350.00 SNOW REMOVAL EQUIPMENTSUBCATEGORY

AMERICAN ROAD MACHINERY, INC.

112S35AR001 $4,892 0.49 0.09 0.00 150.341.18SNOW REMOVAL EQUIPMENT, SNOW PLOW, REVERSIBLE (ADD DUMP TRUCK)

713S35AR002 $6,948 0.69 0.13 0.00 200.481.68SNOW REMOVAL EQUIPMENT, SNOW PLOW, 1-WAY TRIP (ADD DUMP TRUCK)

EP 1110-1-8, Vol. 130 Nov 09

2-213


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

SOIL & ROAD STABILIZERSS400.00 SOIL & ROAD STABILIZERSSUBCATEGORY


360MPH-362 R-2 RECYCLER

S40BO002 $397,893 31.30 7.46 38.80 39023.11125.55SOIL & ROAD STABILIZER, 12" DEEP X 79" WIDE, HYDROSTATIC RECLAIMER/ SOIL STABILIZER, 4X2

HP D-off

360MPH-362 S-2S40BO003 $389,664 30.64 7.31 38.80 39022.63123.88SOIL & ROAD STABILIZER, 14" DEEP X 79" WIDE, HYDROSTATIC RECLAIMER/ SOIL STABILIZER, 4X2

HP D-off

360MPH-362 SDM-2S40BO004 $382,405 30.06 7.17 38.80 39022.20122.41SOIL & ROAD STABILIZER, 21" DEEP X 79" WIDE, HYDROSTATIC RECLAIMER/ SOIL STABILIZER, 4X2

HP D-off


309RR-250BS40CA001 $362,235 28.58 6.79 33.30 37021.08112.21SOIL & ROAD STABILIZER, 12" DEEP X 96" WIDE, HYDROSTATIC RECLAIMER/ SOIL STABILIZER, 4X2

HP D-off

309SS-250BS40CA002 $347,437 27.14 6.52 33.30 30820.09108.77SOIL & ROAD STABILIZER, 18" DEEP X 96" WIDE, HYDROSTATIC RECLAIMER/ SOIL STABILIZER, 4X2

HP D-off

350RM-300S40CA003 $292,574 21.53 5.49 37.72 51816.26109.04SOIL & ROAD STABILIZER, 18" DEEP X 96" WIDE, HYDROSTATIC ROAD RECLAIMER/ SOIL STABILIZER, 4X4

HP D-off

540RM-500S40CA004 $485,999 37.46 9.11 58.20 59927.84169.52SOIL & ROAD STABILIZER, 16" DEEP X 96" WIDE, HYDROSTATIC ROAD RECLAIMER/ SOIL STABILIZER, 4X4

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-214


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

SPLITTERS, ROCK & CONCRETES450.00 SPLITTERS, ROCK & CONCRETESUBCATEGORY

ELCO INTERNATIONAL INC.

8002-2S45DA004 $12,245 1.63 0.24 0.00 11.064.64SPLITTER, ROCK & CONCRETE, 220 TON SFORCE, 1.75" DIA, SIZE 2, 5 GAL, 12" DEEP HOLE REQ'D (ADD 80 CFM COMPRESSOR)

CFM A


CFM A


CFM A

TRACTOR BLADES & ATTACHMENTS (including agricultural)T100.00 TRACTOR BLADES & ATTACHMENTS (including agricultural)SUBCATEGORY


D3-61-9722T10CA001 $13,465 1.08 0.25 0.00 220.792.74TRACTOR ATTACHMENTS, BLADE, POWER ANGLE, HYDRAULIC, FOR D3, 1.65 CY (ADD D3 TRACTOR)

D3-PA 30BT10CA002 $20,185 1.61 0.38 0.00 211.194.07TRACTOR ATTACHMENTS, POWER WINCH, W/250' CABLE, FOR D3 (ADD D3 TRACTOR)


EP 1110-1-8, Vol. 130 Nov 09

2-215


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

T10 CATERPILLAR INC. ( MACHINE DIVISION) (continued)

D4-PA 30BT10CA005 $20,185 1.61 0.38 0.00 211.194.07TRACTOR ATTACHMENTS, POWER WINCH, W/250' CABLE, FOR D4 (ADD D4 TRACTOR)

D5 N - ANGLE BLADE

T10CA007 $22,551 1.80 0.42 0.00 261.324.53TRACTOR ATTACHMENTS, BLADE, POWER ANGLE, HYDRAULIC, FOR D5, 2.53 CY (ADD D5 TRACTOR)

D5-PA 55T10CA008 $30,130 2.41 0.57 0.00 261.786.05TRACTOR ATTACHMENTS, POWER WINCH, FOR D5 (ADD D5 TRACTOR)

D6-108-3970T10CA009 $27,542 2.20 0.52 0.00 571.625.53TRACTOR ATTACHMENTS, BLADE, STRAIGHT, HYDRAULIC, FOR D6, 5.09 CY (ADD D6 TRACTOR)


D6-PA56 WINCHT10CA011 $41,953 3.36 0.79 0.00 272.478.39TRACTOR ATTACHMENTS, POWER WINCH, W/CABLE, FOR D6 (ADD D6 TRACTOR)

D7-ST10CA012 $40,560 3.24 0.76 0.00 772.388.10TRACTOR ATTACHMENTS, BLADE, STRAIGHT, HYDRAULIC, FOR D7, 6.75 CY (ADD D7 TRACTOR)

D7-UT10CA013 $44,541 3.56 0.84 0.00 862.628.89TRACTOR ATTACHMENTS, BLADE, UNIVERSAL, HYDRAULIC, FOR D7, 10.09 CY (ADD D7 TRACTOR)

D7-AT10CA014 $37,061 2.96 0.70 0.00 782.187.41TRACTOR ATTACHMENTS, BLADE, POWER ANGLE, HYDRAULIC, FOR D7, 5.08 CY (ADD D7 TRACTOR)

D7-PA57 WINCHT10CA015 $55,162 4.41 1.03 0.00 453.2411.01TRACTOR ATTACHMENTS, POWER WINCH, W/CABLE, FOR D7 (ADD D7 TRACTOR)

EP 1110-1-8, Vol. 130 Nov 09

2-216


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT


D8-SUT10CA016 $54,028 4.32 1.01 0.00 1073.1710.80TRACTOR ATTACHMENTS, BLADE, STRAIGHT, HYDRAULIC, FOR D8, 6.09 CY (ADD D8 TRACTOR)


D8-AT10CA018 $51,889 4.15 0.97 0.00 1233.0510.39TRACTOR ATTACHMENTS, BLADE, POWER ANGLE, HYDRAULIC, FOR D8, 6.09 CY (ADD D8 TRACTOR)

D8-PPT10CA019 $1,493 0.12 0.03 0.00 50.090.35TRACTOR ATTACHMENTS, BLADE, PUSH PLATE, FOR D8 (ADD D8 TRACTOR)

D8, PA58VS WINCH

T10CA020 $54,980 4.40 1.03 0.00 503.2311.03TRACTOR ATTACHMENTS, POWER WINCH, W/CABLE, FOR D8 (ADD D8 TRACTOR)

D9-SUT10CA021 $73,402 5.87 1.38 0.00 1434.3214.71TRACTOR ATTACHMENTS, BLADE, SEMI-U, HYDRAULIC, FOR D9, 17.70 CY (ADD D9 TRACTOR)


D9, PA59VS WINCH

T10CA023 $73,942 5.92 1.39 0.00 864.3514.84TRACTOR ATTACHMENTS, POWER WINCH, W/CABLE, FOR D9 (ADD D9 TRACTOR)

D10-SU ABRASION

T10CA024 $109,408 8.75 2.05 0.00 3576.4321.92TRACTOR ATTACHMENTS, BLADE, SEMI-U, HYDRAULIC, FOR D10, 24.20 CY (ADD D10 TRACTOR)

D10-U ABRASION

T10CA025 $116,457 9.32 2.18 0.00 2516.8423.33TRACTOR ATTACHMENTS, BLADE, UNIVERSAL, HYDRAULIC, FOR D10, 28.70 CY (ADD D10 TRACTOR)

EP 1110-1-8, Vol. 130 Nov 09

2-217


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)


D11-SUT10CA026 $158,762 12.70 2.98 0.00 3679.3331.81TRACTOR ATTACHMENTS, BLADE, STRAIGHT, HYDRAULIC, FOR D11, 35.50 CY (ADD D11 TRACTOR)


DEERE & COMPANY

915 V-RIPPERT10JD001 $13,345 1.02 0.25 0.00 170.762.91TRACTOR ATTACHMENTS, DEEP TILLER, 5x7 V SHAPED, 175" WIDE, 7 SHANKS (ADD 200HP TRACTOR W/PTO)

TRACTORS, CRAWLER (DOZER) (includes blade)T150.01 0 THRU 225 HPSUBCATEGORY


70D-3G LGPT15CA002 $93,774 6.56 1.88 7.54 1755.1630.05TRACTOR, CRAWLER (DOZER), 70 HP, LOW GROUND PRESSURE, W/2.0 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

80D-4G XLT15CA020 $118,243 8.28 2.37 8.62 1816.5136.87TRACTOR, CRAWLER (DOZER), 80 HP, POWERSHIFT, W/2.18 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

80D-4G LGPT15CA005 $115,853 8.11 2.32 8.62 1846.3836.32TRACTOR, CRAWLER (DOZER), 80 HP, LOW GROUND PRESSURE, W/2.39 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

90D-5G XLT15CA021 $122,404 8.57 2.45 9.70 1956.7439.06TRACTOR, CRAWLER (DOZER), 90 HP, POWERSHIFT, W/2.85 CY POWER ANGLE BLADE (ADD ATTACHMENTS)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-218


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT


90D-5G LGPT15CA022 $129,598 9.07 2.59 9.70 2037.1340.68TRACTOR, CRAWLER (DOZER), 90 HP, LOW GROUND PRESSURE, W/3.04 CY POWER ANGLE BLADE (ADD ATTACHMENTS)

HP D-off

110D-5M XLT15CA024 $165,571 11.59 3.31 11.86 2779.1151.36TRACTOR, CRAWLER (DOZER), 110 HP, POWERSHIFT, W/3.37 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

145D-6N PS XL FTCT15CA008 $230,987 16.17 4.62 15.63 32112.7170.58TRACTOR, CRAWLER (DOZER), 145 HP, POWERSHIFT, W/5.60 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

165D-6RT15CA023 $330,503 23.14 6.62 17.78 51918.1995.64TRACTOR, CRAWLER (DOZER), 165 HP, LOW GROUND PRESSURE, POWERSHIFT, W/5.09 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

165D-6R WHAT15CA009 $330,503 23.14 6.62 17.78 51918.1995.64TRACTOR, CRAWLER (DOZER), 165 HP, W/14.3 CY BLADE, TRASH/WASTE HANDLING ARRANGEMENT

HP D-off

185D-6R LGPT15CA011 $321,902 22.53 6.44 19.94 46117.7196.21TRACTOR, CRAWLER (DOZER), 165 HP, LOW GROUND PRESSURE, W/5.09 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

CASE CORPORATION

67550H WTT15CS004 $105,525 7.39 2.11 7.22 1465.8132.34TRACTOR, CRAWLER (DOZER), 67 HP, POWERSHIFT, W/1.90 CY UNIVERSAL BLADE (ADD ATTACHMENTS)

HP D-off

1191150H WTT15CS007 $184,140 12.89 3.69 12.83 26310.1456.71TRACTOR, CRAWLER (DOZER), 119 HP, POWERSHIFT, W/3.90 CY UNIVERSAL BLADE (ADD ATTACHMENTS)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-219


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

DEERE & COMPANY

70450H LTT15JD005 $84,409 5.91 1.69 7.54 1554.6527.93TRACTOR, CRAWLER (DOZER), 70 HP, POWERSHIFT, W/2.00 CY ANGLE BLADE (ADD ATTACHMENTS)

HP D-off

74450H LGPT15JD006 $100,378 7.03 2.01 7.98 1655.5332.07TRACTOR, CRAWLER (DOZER), 74 HP, LOW GROUND PRESSURE, W/2.15 CY ANGLE BLADE (ADD ATTACHMENTS)

HP D-off

90650HT15JD007 $115,327 8.07 2.31 9.70 1856.3537.46TRACTOR, CRAWLER (DOZER), 90 HP, POWERSHIFT, W/2.60 CY ANGLE BLADE (ADD ATTACHMENTS)

HP D-off

140750C-II LTT15JD008 $203,618 14.25 4.08 15.09 31711.2163.76TRACTOR, CRAWLER (DOZER), 140 HP, POWERSHIFT, W/5.60 CY ANGLE BLADE (ADD ATTACHMENTS)

HP D-off

140750C-II LGPT15JD009 $214,254 15.00 4.29 15.09 36511.7966.17TRACTOR, CRAWLER (DOZER), 140 HP, LOW GROUND PRESSURE, W/4.84 CY ANGLE BLADE (ADD ATTACHMENTS)

HP D-off

185850CT15JD010 $265,484 18.58 5.31 19.94 40414.6083.44TRACTOR, CRAWLER (DOZER), 185 HP, POWERSHIFT, W/7.44 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

185850C LGPT15JD011 $287,392 20.12 5.75 19.94 42015.8188.40TRACTOR, CRAWLER (DOZER), 185 HP, LOW GROUND PRESSURE, W/7.14 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-220


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

0.02 226 HP THRU 425 HPSUBCATEGORY


240D-7R SERIES IIT15CA012 $383,306 23.00 7.32 25.87 56318.82105.21TRACTOR, CRAWLER (DOZER), 240 HP, POWERSHIFT, W/8.98 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

240D-7R II LGPT15CA014 $454,576 27.27 8.68 25.87 53022.32119.31TRACTOR, CRAWLER (DOZER), 240 HP, LOW GROUND PRESSURE, W/7.70 CY STRAIGHT BLADE (ADD ATTACHMENTS)

HP D-off

310D-8R IIT15CA016 $505,853 30.35 9.66 33.41 89824.84138.01TRACTOR, CRAWLER (DOZER), 310 HP, POWERSHIFT, W/15.3 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

410D-9RT15CA017 $672,306 40.34 12.84 44.19 1,03333.01183.18TRACTOR, CRAWLER (DOZER), 410 HP, POWERSHIFT, W/17.7 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off


310D155AX-5T15KM008 $578,075 34.68 11.04 33.41 80328.38152.30TRACTOR, CRAWLER (DOZER), 310 HP, POWERSHIFT, W/11.5 CY SEMI-U BLADE

HP D-off

0.03 OVER 425 HPSUBCATEGORY


580D-10RT15CA018 $954,895 50.93 17.42 53.32 1,42142.89220.21TRACTOR, CRAWLER (DOZER), 580 HP, POWERSHIFT, W/28.7 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

850D-11RT15CA019 $1,482,146 79.05 27.03 78.14 2,02966.56336.83TRACTOR, CRAWLER (DOZER), 850 HP, POWERSHIFT, W/44.0 CY SEMI-U BLADE (ADD ATTACHMENTS)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-221


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

TRACTORS, WHEEL TYPE (DOZER)T200.00 TRACTORS, WHEEL TYPE (DOZER)SUBCATEGORY


240814-FT20CA001 $348,008 20.62 6.15 22.06 47916.4674.50TRACTOR, WHEEL (DOZER), 240 HP, ARTICULATING, 4X4, W/3.77 CY STRAIGHT BLADE

HP D-off

339824-G IIT20CA002 $506,298 29.22 8.94 31.16 63323.55112.07TRACTOR, WHEEL (DOZER), 339 HP, ARTICULATING, 4X4, W/6.70 CY STRAIGHT BLADE

HP D-off

481834-GT20CA003 $763,003 42.89 13.48 44.22 90234.93163.03TRACTOR, WHEEL (DOZER), 481 HP, ARTICULATING, 4X4, W/10.33 CY STRAIGHT BLADE

HP D-off

TRACTORS, AGRICULTURALT250.10 CRAWLERSUBCATEGORY


267CH 65ET25CA006 $201,444 17.12 3.66 26.24 33112.2272.52TRACTOR, AGRICULTURAL, CRAWLER-RUBBER TRACK, 267 HP, 3 POINT HITCH

HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-222


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

0.20 WHEELSUBCATEGORY

DEERE & COMPANY

455103T25JD015 $17,921 1.72 0.33 4.42 391.199.33TRACTOR, AGRICULTURAL, WHEEL, 45 HP, 4X2, PTO, 3 POINT HITCH

HP D-off


HP D-off

565225 W/609 MOWER

T25JD017 $29,878 2.99 0.55 5.50 512.0513.38TRACTOR, AGRICULTURAL, WHEEL, 56 HP, 4X2, PTO, 3 POINT HITCH, WITH 60" HEAVY DUTY ROTARY MOWER

HP D-off


HP D-off


HP D-off


HP D-off


HP D-off


HP D-off


HP D-off


HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-223


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

TRENCHERS, CHAIN TYPE CUTTERT300.00 TRENCHERS, CHAIN TYPE CUTTERSUBCATEGORY

DITCH WITCH(The Charles Machine Works)I

131230T30DW012 $9,091 0.88 0.17 2.31 80.615.02TRENCHER, CHAIN TYPE CUTTER, 36" DEEP X 6" WIDE, WALK BEHIND

HP G

181820T30DW013 $12,804 1.22 0.25 3.20 130.867.02TRENCHER, CHAIN TYPE CUTTER, 48" DEEP X 16" WIDE, WALK BEHIND

HP G

353610T30DW014 $33,555 3.14 0.64 3.44 392.2112.76TRENCHER, CHAIN TYPE CUTTER, 60" DEEP X 16" WIDE, 4X4 (W/BLADE)

HP D-off

443700T30DW005 $35,629 3.44 0.68 4.32 422.4014.28TRENCHER, CHAIN TYPE CUTTER, 63" DEEP X 12" WIDE, 4X4 (W/DBL PIVOT)

HP D-off

575700T30DW016 $57,960 5.67 1.11 5.60 953.9521.63TRENCHER, CHAIN TYPE CUTTER, 52" DEEP X 12" WIDE, 4X4 (W/BLADE)

HP D-off

70RT 70 MT30DW017 $72,742 7.06 1.39 6.88 694.9226.99TRENCHER, CHAIN TYPE CUTTER, 96" DEEP X 24" WIDE, 4X4 (W/BLADE)

HP D-off

78RT 90 MT30DW018 $81,441 7.93 1.56 7.67 775.5330.18TRENCHER, CHAIN TYPE CUTTER, 96" DEEP X 24" WIDE, 4X4 (W/BLADE)

HP D-off

185HT185 (H1812)T30DW011 $202,134 20.21 3.87 18.18 19513.9873.89TRENCHER, CHAIN TYPE CUTTER, 84" DEEP X 9"-24" WIDE, CRAWLER (W/BLADE)

HP D-off

TESMEC USA, INC.

185TRS 900-AT30TM001 $305,717 30.57 5.86 18.18 37521.15101.21TRENCHER, CHAIN TYPE CUTTER, 3' DEEP X 4"-8" WIDE, CRAWLER (W/CRUMBSHOE)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-224


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

T30 TESMEC USA, INC. (continued)185TRS 900-A-SLT30TM004 $330,130 33.01 6.32 18.18 40022.83107.63TRENCHER, CHAIN TYPE CUTTER, 3'

DEEP X 4"-8" WIDE, CRAWLER (W/CRUMBSHOE) SELF LEVEL

HP D-off

270TRS 1000-AT30TM009 $428,965 42.90 8.22 26.53 55029.67143.17TRENCHER, CHAIN TYPE CUTTER, 4' DEEP X 5"-12" WIDE, CRAWLER (W/CRUMBSHOE)

HP D-off

220TRS 775T30TM007 $435,891 43.59 8.35 21.62 45030.15139.43TRENCHER, CHAIN TYPE CUTTER, 4' DEEP X 12" WIDE, CRAWLER (W/CRUMBSHOE) SELF LEVEL, OFFSET

HP D-off

220TRS 775T30TM008 $438,780 43.88 8.41 21.62 47030.35140.19TRENCHER, CHAIN TYPE CUTTER, 6' DEEP X 18" WIDE, CRAWLER (W/CRUMBSHOE) SELF LEVEL, OFFSET

HP D-off

385TRS 1100T30TM012 $748,361 74.84 14.34 37.83 85051.76240.18TRENCHER, CHAIN TYPE CUTTER, 8' DEEP X 26" WIDE, CRAWLER (W/CRUMBSHOE)

HP D-off

525TRS 1475 XHPT30TM014 $1,174,748 117.47 22.50 51.59 1,68081.24368.17TRENCHER, CHAIN TYPE CUTTER, 10' DEEP X 26" WIDE, CRAWLER (W/CRUMBSHOE)

HP D-off


HP D-off


HP D-off

VERMEER MANUFACTURING CO.

125T 455T30VE007 $170,275 17.03 3.26 12.28 18011.7858.80TRENCHER, CHAIN TYPE CUTTER, 6' DEEP X 8"-24" WIDE, CRAWLER, HYDROSTATIC

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-225


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

T30 VERMEER MANUFACTURING CO. (continued)

185T 555 IIIT30VE008 $216,352 21.64 4.14 18.18 22514.9677.64TRENCHER, CHAIN TYPE CUTTER, 8' DEEP X 8"-24" WIDE, CRAWLER, HYDROSTATIC

HP D-off

250T 655 IIIT30VE009 $350,502 35.05 6.71 24.57 50024.24120.25TRENCHER, CHAIN TYPE CUTTER, 8' DEEP X 10.5"-26" WIDE, CRAWLER, HYDROSTATIC

HP D-off

275T 755 IIIT30VE010 $424,516 42.45 8.13 27.02 66029.36142.54TRENCHER, CHAIN TYPE CUTTER, 10' DEEP X 14"-36" WIDE, CRAWLER, HYDROSTATIC

HP D-off

TRENCHERS, WHEEL TYPE CUTTERT350.00 TRENCHERS, WHEEL TYPE CUTTERSUBCATEGORY

CLEVELAND TRENCHER

1409624T35CT001 $229,696 22.97 4.40 13.76 17015.8976.15TRENCHER, WHEEL TYPE CUTTER, 72" DEEP X 21.5" WIDE, ROUND BUCKET, CRAWLER

HP D-off

1409600-ST35CT002 $282,912 28.29 5.42 13.76 22819.5790.18TRENCHER, WHEEL TYPE CUTTER, 72" DEEP X 24" WIDE, ROUND BUCKET, CRAWLER

HP D-off

185246-FDT35CT003 $317,808 31.78 6.09 18.18 32021.98104.39TRENCHER, WHEEL TYPE CUTTER, 84" DEEP X 24" WIDE, ROUND BUCKET, CRAWLER

HP D-off

1027036T35CT005 $283,161 28.32 5.42 10.02 26319.5886.01TRENCHER, WHEEL TYPE CUTTER, 84" DEEP X 36" WIDE, ROUND BUCKET, CRAWLER

HP D-off


HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-226


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

T35 CLEVELAND TRENCHER (continued)1027036-HDT35CT004 $299,362 29.94 5.73 10.02 28620.7090.28TRENCHER, WHEEL TYPE CUTTER, 84"

DEEP X 36" WIDE, ROUND BUCKET, CRAWLER

HP D-off

1027036-SDT35CT007 $313,359 31.34 6.00 10.02 34021.6793.97TRENCHER, WHEEL TYPE CUTTER, 84" DEEP X 36" WIDE, ROUND BUCKET, CRAWLER

HP D-off


HP D-off

1507648-SDT35CT009 $467,117 46.71 8.95 14.74 44532.31139.86TRENCHER, WHEEL TYPE CUTTER, 90" DEEP X 48" WIDE, ROUND BUCKET, CRAWLER

HP D-off


HP D-off

175400W-HDT35CT011 $549,068 54.91 10.52 17.20 70037.98164.26TRENCHER, WHEEL TYPE CUTTER, 108" DEEP X 72" WIDE, ROUND BUCKET, CRAWLER

HP D-off

TRUCK OPTIONST400.10 CRANES / HOISTS, PERSONNEL & MATERIAL HANDLINGSUBCATEGORY

AUTO CRANE CO.

AC8-59T40AH001 $26,380 2.64 0.51 0.00 21.836.65TRUCK OPTIONS, CRANE, HYDRAULIC, 3-ARM ARTICULATING, 3.5 TON, 32' BOOM (ADD 21,000 GVW TRUCK & FLATBED)

EP 1110-1-8, Vol. 130 Nov 09

2-227


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

T40 AUTO CRANE CO. (continued)AC15-101T40AH003 $39,100 3.91 0.75 0.00 32.719.73TRUCK OPTIONS, CRANE, HYDRAULIC, 3-

ARM ARTICULATING, 6.6 TON, 36' BOOM (ADD 32,500 GVW TRUCK & FLATBED)

AC20-142T40AH004 $48,362 4.84 0.93 0.00 83.3511.99TRUCK OPTIONS, CRANE, HYDRAULIC, 3-ARM ARTICULATING, 8.6 TON, 41' BOOM (ADD 46,000 GVW TRUCK & FLATBED)

PALFINGER INC.

PC 2300T40PA001 $7,836 0.78 0.15 0.00 90.542.14TRUCK OPTIONS, CRANE, HYDRAULIC, 2-ARM ARTICULATING, 2.4 TON, 21' BOOM (ADD 25,000 GVW TRUCK & FLATBED)

PK 12502T40PA002 $43,145 4.31 0.83 0.00 352.9910.70TRUCK OPTIONS, CRANE, HYDRAULIC, 3-ARM ARTICULATING, 5.3 TON, 61' BOOM (ADD 28,000 GVW TRUCK & FLATBED)



PK 50002T40PA005 $119,681 11.97 2.29 0.00 1,0728.2829.30TRUCK OPTIONS, CRANE, HYDRAULIC, 2-ARM ARTICULATING, 12.5 TON, 82' BOOM (ADD 60,000 GVW TRUCK & FLATBED)

EP 1110-1-8, Vol. 130 Nov 09

2-228


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

T40 PALFINGER INC. (continued)PK 65002T40PA006 $122,712 12.27 2.35 0.00 1268.4930.03TRUCK OPTIONS, CRANE, HYDRAULIC, 2-

ARM ARTICULATING, 14.9 TON, 82' BOOM (ADD 62,000 GVW TRUCK & FLATBED)

0.20 DUMP BODY, REARSUBCATEGORY

GALION DUMP BODIES, INC.

PACKAGE 89-FT40GN001 $15,452 1.74 0.28 0.00 421.153.69TRUCK OPTIONS, DUMP BODY, REAR, 16-23.5 CY (W/HOIST) (ADD 36,000 GVW TRUCK)

MIDLAND MANUFACTURING INC.

KLEENSIDET40MY002 $5,141 0.58 0.09 0.00 210.381.23TRUCK OPTIONS, DUMP BODY, REAR, 7.5 CY, AIR GATE (W/HOIST) (ADD 30,000 GVW TRUCK)





EP 1110-1-8, Vol. 130 Nov 09

2-229


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

0.30 FLATBEDS, WITH SIDESSUBCATEGORY

KNAPHEIDE MANUFACTURING CO.

8' X 8'T40KF011 $2,677 0.27 0.05 0.00 110.190.57TRUCK OPTIONS, FLATBED, W/SIDE RACKS, 8' X 8'






0.41 HOIST, ELECTRIC DRIVESUBCATEGORY

KNAPHEIDE MANUFACTURING CO.

KH-1416LT40KF021 $2,927 0.29 0.06 0.00 60.210.77TRUCK OPTIONS, HOIST, ELECTRIC DRIVE, PTO, 10' TO 14', 7-16 TON

KH-1416L-EET40KF023 $3,923 0.39 0.08 0.00 60.280.94TRUCK OPTIONS, HOIST, ELECTRIC DRIVE, 10' TO 14', 7-16 TON

KH-1627L-EET40KF024 $4,620 0.46 0.09 0.00 100.321.10TRUCK OPTIONS, HOIST, ELECTRIC DRIVE, 15' TO 20', 14-37 TON

KH-2538LT40KF022 $5,814 0.58 0.11 0.00 150.401.42TRUCK OPTIONS, HOIST, ELECTRIC DRIVE, PTO, 20' TO 24', 20-45 TON

EP 1110-1-8, Vol. 130 Nov 09

2-230


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

0.50 TRANSIT MIXERSSUBCATEGORY


235RDTM-8T40XX034 $146,042 15.52 2.71 27.03 26610.4765.14TRANSIT MIXER, 8 CY, HYDROSTATIC, 100 GAL, (INCLUDES 60,000 GVW TRUCK)

HP D-on


HP D-on


HP D-on


HP D-on


HP D-on

0.60 WATER TANKSSUBCATEGORY


DS 2000T40RS001 $28,801 2.70 0.57 0.00 381.925.94TRUCK OPTIONS, WATER TANK, 2,000 GAL (ADD 28,000 GVW TRUCK)



EP 1110-1-8, Vol. 130 Nov 09

2-231


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

0.70 ALL OTHER OPTIONSSUBCATEGORY

ARROW-MASTER, INC.

801350T40AG001 $84,726 8.25 1.62 7.86 965.7528.34TRUCK OPTIONS, GUILLOTINE CONCRETE BREAKER, W/8'' DIA BREAKING TOOL AND CAB

HP D-off

TRUCK TRAILERST450.10 BOTTOM DUMPSUBCATEGORY


40' MC 2000T45MY004 $30,973 2.41 0.54 0.00 1521.756.77TRUCK TRAILER, BOTTOM DUMP, 21 CY, 28 TON, 40' - 2 AXLE, CLAMSHELL (ADD TOWING TRUCK)

40' TC 3000T45MY005 $41,745 3.19 0.73 0.00 1382.339.09TRUCK TRAILER, BOTTOM DUMP, 21 CY, 30 TON, 40' - 3 AXLE, CLAMSHELL (ADD TOWING TRUCK)




T45XX001 $38,174 3.13 0.67 0.00 1222.248.18TRUCK TRAILER, BOTTOM DUMP, 27 TON (ADD TOWING TRUCK)

T45XX003 $51,059 4.29 0.89 0.00 1603.0410.68TRUCK TRAILER, BOTTOM DUMP, 30 TON (ADD TOWING TRUCK)

EP 1110-1-8, Vol. 130 Nov 09

2-232


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

0.20 END DUMPSUBCATEGORY


28' SK2000T45MY015 $33,065 2.60 0.58 0.00 1151.887.10TRUCK TRAILER, END DUMP, 28 CY, 36 TON, 28' - 2 AXLE (W/HOIST) (ADD TOWING TRUCK)

32' ST 2400T45MY016 $33,713 2.65 0.59 0.00 1301.927.21TRUCK TRAILER, END DUMP, 28 CY, 36 TON, 32' - 2 AXLE (W/HOIST) (ADD TOWING TRUCK)

39' SK 2300T45MY017 $37,418 2.80 0.66 0.00 1702.068.16TRUCK TRAILER, END DUMP, 39 CY, 50 TON, 39' - 3 AXLE (W/HOIST) (ADD TOWING TRUCK)


T45XX008 $32,093 2.58 0.56 0.00 1101.856.82TRUCK TRAILER, END DUMP, 20 CY, 24 TON (ADD TOWING TRUCK)

0.30 PUP TRAILERSUBCATEGORY


14' SK 2100T45MY018 $22,250 2.03 0.40 0.00 801.425.71TRUCK TRAILER, PUP TRAILER, 10 CY, 13 TON, 14' - 2 AXLE (W/HOIST) (ADD TOWING TRUCK)

14' SL 2100T45MY019 $22,072 2.01 0.40 0.00 801.415.67TRUCK TRAILER, PUP TRAILER, 12 CY, 15 TON, 14' - 2 AXLE (W/HOIST) (ADD TOWING TRUCK)


T45XX009 $32,577 3.28 0.59 0.00 862.237.95TRUCK TRAILER, PUP TRAILER, 8 CY, LONG TONGUE (ADD TOWING TRUCK)

EP 1110-1-8, Vol. 130 Nov 09

2-233


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

T45 NO SPECIFIC MANUFACTURER (continued)T45XX010 $32,686 3.30 0.59 0.00 862.247.98TRUCK TRAILER, PUP TRAILER, 10 CY,

LONG TONGUE (ADD TOWING TRUCK)

T45XX032 $40,933 4.32 0.74 0.00 922.909.84TRUCK TRAILER, PUP TRAILER, 13 CY, 14.5 TON, 3 AXLE (ADD TOWING TRUCK)

T45XX033 $48,215 5.04 0.87 0.00 1003.3911.64TRUCK TRAILER, PUP TRAILER, 16 CY, 18.0 TON, 4 AXLE (ADD TOWING TRUCK)

0.41 LOWBOY, RIGID NECK, DROP DECKSUBCATEGORY

EAGER BEAVER

35GSL-BRT45EA006 $43,123 3.35 0.76 0.00 1502.448.58TRUCK TRAILER, LOWBOY, 35 TON, 2 AXLE, DETATCHABLE GOOSENECK (ADD TOWING TRUCK)

50GSL/3T45EA007 $64,104 4.97 1.12 0.00 2053.6112.51TRUCK TRAILER, LOWBOY, 50 TON, 3 AXLE , DETATCHABLE GOOSENECK (ADD TOWING TRUCK)


T45XX011 $32,281 2.63 0.57 0.00 951.896.26TRUCK TRAILER, LOWBOY, 25 TON, 2 AXLE (ADD TOWING TRUCK)




EP 1110-1-8, Vol. 130 Nov 09

2-234


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

T45 NO SPECIFIC MANUFACTURER (continued)T45XX015 $44,965 3.64 0.79 0.00 1362.618.71TRUCK TRAILER, LOWBOY, 40 TON, 3

AXLE (ADD TOWING TRUCK) T45XX016 $50,292 4.07 0.88 0.00 1452.929.68TRUCK TRAILER, LOWBOY, 50 TON, 3








AXLE (ADD TOWING TRUCK)

0.50 FLATBED TRAILERSUBCATEGORY


T45XX025 $30,635 2.45 0.54 0.00 1101.775.74TRUCK TRAILER, FLATBED, 25 TON, 2 AXLE (ADD TOWING TRUCK)

32T45XX034 $30,088 2.40 0.53 0.00 1031.735.95TRUCK TRAILER, FLATBED, 40 TON, 2 AXLE (ADD TOWING TRUCK)

40T45XX035 $31,980 2.57 0.56 0.00 1101.856.26TRUCK TRAILER, FLATBED, 40 TON, 2 AXLE (ADD TOWING TRUCK)

EP 1110-1-8, Vol. 130 Nov 09

2-235


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

0.60 MISCELLANEOUS / UTILITYSUBCATEGORY


T45XX026 $17,326 1.39 0.30 0.00 621.003.57TRUCK TRAILER, MISCELLANEOUS/UTILITY, TILT BED, 12 TON, 2 AXLE (ADD TOWING TRUCK)



T45XX024 $28,245 2.24 0.49 0.00 621.615.32TRUCK TRAILER, MISCELLANEOUS/UTILITY, ATTACHMENT, HELPER DOLLY, 60 TON TRAILER MAX (ADD TOWING TRUCK)

0.70 WATER TANKER TRAILERSUBCATEGORY


63T45XX029 $79,814 5.83 1.55 6.19 1704.4720.54TRUCK TRAILER, WATER TANKER, 4,000 GAL, W/PUMP (ADD TOWING TRUCK)

HP D-off


HP D-off


HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-236


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

TRUCKS, HIGHWAY (Add attachments as required)T500.01 0 THRU 10,000 GVWSUBCATEGORY

GMC AND CHEVROLET

120S10 T50GM001 $16,095 1.54 0.31 5.06 261.089.48TRUCK, HIGHWAY, 3,500 GVW, 4X2 (COMPACT)

HP G

285R26T50GM004 $35,789 3.51 0.69 12.01 502.4521.85TRUCK, HIGHWAY, 8,600 GVW, 4X2 (SUBURBAN)

HP G

285V26T50GM005 $38,472 3.78 0.74 12.01 522.6322.47TRUCK, HIGHWAY, 8,600 GVW, 4X4 (SUBURBAN)

HP G


1304X2 1/2 130 CONV GAS

T50XX001 $15,663 1.46 0.30 5.48 451.039.90TRUCK, HIGHWAY, CONVENTIONAL, 1/2 TON PICKUP, 4X2

HP G

1304X2 3/4 130 CONV GAS


HP G

1804X2 1 180 CONV GAS

T50XX003 $21,223 2.04 0.41 7.59 411.4313.54TRUCK, HIGHWAY, CONVENTIONAL, 1 TON PICKUP, 4X2

HP G

1304X4 1/2 130 CONV GAS


HP G

1304X4 3/4 130 CONV GAS


HP G

1804X4 1 180 CONV GAS


HP G

1304X2 1/2 130 CREW GAS

T50XX007 $16,525 1.55 0.32 5.48 451.1010.10TRUCK, HIGHWAY, CREW, 1/2 TON PICKUP, 4X2

HP G

1304X2 3/4 130 CREW GAS


HP G

EP 1110-1-8, Vol. 130 Nov 09

2-237


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

T50 NO SPECIFIC MANUFACTURER (continued)1804X2 1 180

CREW GAST50XX009 $24,300 2.35 0.47 7.59 451.6514.24TRUCK, HIGHWAY, CREW, 1 TON PICKUP,

4X2 HP G

1304X4 1/2 130 CREW GAS


HP G

1804X4 3/4 180 CREW GAS


HP G

1804X4 1 180 CREW GAS

T50XX012 $25,002 2.42 0.48 7.59 451.6914.40TRUCK, HIGHWAY, CREW, 1 TON PICKUP, 4X4

HP G

754X2 1/2 75 CONV DSL


HP D-on

754X2 3/4 75 CONV DSL


HP D-on

1304X2 1 130 CONV DSL


HP D-on

1304X4 1/2 130 CONV DSL


HP D-on

1304X4 3/4 130 CONV DSL


HP D-on

130CONV DSL 4X4 1 130


HP D-on

1304X2 3/4 130 CREW DSL


HP D-on

1304X4 3/4 130 CREW DSL

T50XX020 $28,088 2.73 0.54 3.38 551.9110.27TRUCK, HIGHWAY, CREW, 3/4 TON PICKUP 4X4

HP D-on

1304X2 1 130 CREW DSL

T50XX021 $25,488 2.47 0.49 3.38 481.739.67TRUCK, HIGHWAY, CREW, 1 TON PICKUP, 4X2

HP D-on

EP 1110-1-8, Vol. 130 Nov 09

2-238


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

0.02 OVER 10,000 THRU 30,000 GVW (Chassis only - Add options)SUBCATEGORY


2104X2 20KGVW GAS

T50XX023 $40,019 3.06 0.75 20.23 702.2830.48TRUCK, HIGHWAY, 20,000 LBS GVW, 2 AXLE, 4X2 (CHASSIS ONLY-ADD OPTIONS)

HP G

2104X2 25KGVW GAS


HP G

1804X2 25KGVW DSL


HP D-on

1704X4 30KGVW DSL


HP D-on

2104X2 30KGVW DSL


HP D-on

2104X2 30KGVW DSL

T50XX035 $94,270 7.33 1.77 13.24 1355.4432.10TRUCK, HIGHWAY, 30,000 LBS GVW, 2 AXLE, 4X2, WITH 3-ARM ARTICULATING CRANE, 3.5 TON, 32' BOOM, WITH 8' X 20' FLATBED

HP D-on

0.03 OVER 30,000 GVW (Chassis only - Add options)SUBCATEGORY


2654X2 35KGVW DSL


HP D-on

EP 1110-1-8, Vol. 130 Nov 09

2-239


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

T50 NO SPECIFIC MANUFACTURER (continued)2654X2 35KGVW

DSLT50XX032 $116,998 7.62 2.16 23.60 1605.9744.88DUMP TRUCK, HIGHWAY, 35,000 LBS

GVW, 2 AXLE, 4X2 WITH REAR 10 - 13 CY DUMP BODY

HP D-on

2306X4 45KGVW DSL


HP D-on

3106X4 55KGVW DSL


HP D-on

3506X6 70KGVW DSL


HP D-on

4006X4 75KGVW DSL


HP D-on

4006X4 75KGVW DSL

T50XX033 $127,563 8.27 2.36 35.62 2406.5060.26DUMP TRUCK, HIGHWAY, 75,000 LBS GVW, 3 AXLE, 6X4 WITH REAR 16 - 20 CY DUMP BODY

HP D-on

TRUCKS, OFF-HIGHWAYT550.10 RIGID FRAMESUBCATEGORY


487769DT55CA007 $645,044 26.32 11.17 26.24 66824.33113.58TRUCK, OFF-HIGHWAY, RIGID FRAME, 31.7 CY, 41.6 TON, 4X4, REAR DUMP

HP D-off

650773DT55CA002 $867,731 34.99 15.03 35.03 87232.53147.22TRUCK, OFF-HIGHWAY, RIGID FRAME, 46.9 CY, 57.7 TON, 4X4, REAR DUMP

HP D-off

938777DT55CA003 $1,199,572 47.45 20.78 50.55 1,41944.51209.50TRUCK, OFF-HIGHWAY, RIGID FRAME, 78.6 CY, 100 TON, 4X4, REAR DUMP

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-240


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT


488HD325-6T55KM009 $646,875 26.40 11.20 26.30 70724.40113.86TRUCK, OFF-HIGHWAY, RIGID FRAME, 31.4 CY, 44 TON, 4X4, REAR DUMP

HP D-off

1,042HD785-5T55KM012 $951,166 36.89 16.47 56.15 1,54234.92187.55TRUCK, OFF-HIGHWAY, RIGID FRAME, 78.7 CY, 100 TON, 4X4, REAR DUMP

HP D-off

1,486HD1500-5T55KM013 $2,201,784 87.99 38.14 80.08 5,50082.14366.41TRUCK, OFF-HIGHWAY, RIGID FRAME, 102 CY, 165 TON, 4X4, REAR DUMP

HP D-off

2,000730ET55KM014 $2,602,312 99.06 45.07 107.78 7,15094.60467.07TRUCK, OFF-HIGHWAY, RIGID FRAME, 145 CY, 205 TON, 4X4, REAR DUMP

HP D-off

0.20 ARTICULATED FRAMESUBCATEGORY


260D25DT55CA008 $406,953 25.25 7.22 19.78 42919.8592.23TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 18 CY, 25 TON, 4X4, REAR DUMP

HP D-off

285D30DT55CA009 $482,059 29.64 8.56 21.68 47323.38108.62TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 22 CY, 30 TON, 4X4, REAR DUMP

HP D-off

214D250D SERIES IIT55CA010 $405,549 25.81 7.20 16.28 42420.1185.23TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 18 CY, 25 TON, 6X6, REAR DUMP

HP D-off

260D300E SERIES IIT55CA011 $479,395 30.35 8.51 19.78 48823.69102.09TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 22 CY, 30 TON, 6X6, REAR DUMP

HP D-off


HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-241


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)



HP D-off

DEERE & COMPANY

265250DT55JD001 $317,540 19.77 5.64 20.16 35515.5376.96TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 18 CY, 25 TON, 6X6, REAR DUMP

HP D-off


HP D-off


HP D-off


HP D-off


389HM350-1T55KM015 $576,531 35.49 10.23 29.60 63027.98134.04TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 19.1-25.9 CY, 35.7 TON, 6 X 6 X 2, REAR DUMP

HP D-off

430HM400-1T55KM016 $658,665 40.43 11.69 32.71 66831.91152.49TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 21.6-29.2 CY, 40.3 TON, 6 X 6 X 2, REAR DUMP

HP D-off

VOLVO CONSTRUCTION EQUIPMENT GROUP

299A-25E 4X4T55VO002 $346,702 21.38 6.15 22.75 42916.8485.90TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 14-18 CY, 25 TON, 4X4, REAR DUMP

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-242


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

T55 VOLVO CONSTRUCTION EQUIPMENT GROUP (continued)

299A-25ET55VO003 $366,160 22.88 6.50 22.75 47517.9487.78TRUCK, OFF-HIGHWAY, ARTICULATED FRAME, 14-18 CY, 25 TON, 6X6, REAR DUMP

HP D-off


HP D-off


HP D-off


HP D-off

TRUCKS,OFF-HIGHWAY/PRIME MOVER TRACTORS & WAGONST560.10 PRIME MOVER TRACTORSSUBCATEGORY


938776DT56CA006 $1,333,857 53.16 23.10 56.50 1,16449.68233.83TRUCK, OFF-HIGHWAY, RIGID FRAME, PRIME MOVER TRACTOR, 4X4

HP D-off

TRUCKS, VACUUMT570.00 TRUCKS, VACUUMSUBCATEGORY

WASTEQUIP CUSCO INDUSTRIES

76INDUSTRIAL VAC 130

T57CU001 $98,621 7.84 1.85 7.47 765.7728.27TRAILER, VACUUM, 5,500 GAL, 750 CFM, REAR DOOR & HYDRAULIC DUMP SYSTEM

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-243


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

T57 WASTEQUIP CUSCO INDUSTRIES (continued)

76SS INDUST. VAC 130

T57CU002 $136,478 10.87 2.56 7.47 768.0035.74TRAILER, VACUUM, 5,500 GAL, 750 CFM, STAINLESS STEEL, REAR DOOR & HYDRAULIC DUMP SYSTEM

HP D-off

1152127T57CU003 $144,937 11.55 2.72 11.30 1158.5041.76TRUCK, VACUUM, 3,500 GAL, 2,100 CFM, REAR DOOR & HYDRAULIC DUMP SYSTEM

HP D-off


HP D-off


HP D-off

TRUCKS, WATER, OFF-HIGHWAYT600.00 TRUCKS, WATER, OFF-HIGHWAYSUBCATEGORY

KLEIN PRODUCTS, INC.

175KT-50 T60KI001 $263,460 16.95 4.87 17.20 32013.3563.07TRUCK, WATER, OFF-HIGHWAY, 5,000 GAL, W/CAT 613C TRACTOR

HP D-off

330KT-60 T60KI002 $408,273 25.44 7.55 32.43 58020.27108.27TRUCK, WATER, OFF-HIGHWAY, 6,000 GAL, W/CAT 621E TRACTOR

HP D-off


HP D-off


HP D-off

550KT-120 T60KI006 $804,521 49.22 14.88 54.05 1,09739.49205.72TRUCK, WATER, OFF-HIGHWAY, 12,000 GAL, W/CAT 651E TRACTOR

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-244


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT


330STT-60 T60SO001 $472,828 29.75 8.75 32.43 61023.63118.36TRUCK, WATER, OFF-HIGHWAY, 6,000 GAL, W/CAT 621E TRACTOR

HP D-off


HP D-off


HP D-off

550STT-120 T60SO004 $831,070 52.82 15.37 54.05 1,14941.78202.44TRUCK, WATER, OFF-HIGHWAY, 12,000 GAL, W/CAT 651E TRACTOR

HP D-off

550STT-140 T60SO005 $845,061 53.75 15.63 54.05 1,18442.51204.62TRUCK, WATER, OFF-HIGHWAY, 14,000 GAL, W/CAT 651E TRACTOR

HP D-off

TUNNEL/MINING EQUIPMENTT650.10 DRIFTING & TUNNELING DRILLSSUBCATEGORY

ATLAS COPCO WAGNER

158L2CT65WG012 $1,518,574 91.79 26.83 20.92 52072.73281.07156 HP D-offTUNNELING DRILL, 2 BOOM, 560-1,120 SF CROSS SECTION, RUBBER TIRED (ADD DRILL BITS AND DRILL STEEL COST)

HP E

158WL2CT65WG013 $2,283,679 138.24 40.34 20.92 728109.46405.96156 HP D-offTUNNELING DRILL, 4 BOOM, 700-1,600 SF CROSS SECTION, RUBBER TIRED (ADD DRILL BITS AND DRILL STEEL COST)

HP E

380WL4CT65WG014 $2,492,552 150.92 44.03 47.43 1,058119.49481.70224 HP D-offTUNNELING DRILL, 4 BOOM, 700-1,650 SF CROSS SECTION, RUBBER TIRED (ADD DRILL BITS AND DRILL STEEL COST)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-245


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

WATER & CO2 BLASTERSW250.10 LOW PRESSURE, (< 5,000 PSI)SUBCATEGORY

SIOUX STEAM CLEANER CORPORATION

1S1.7 D250W25SD006 $5,499 1.10 0.12 0.13 40.677.28WATER BLASTER, LOW PRESSURE, STEAM CLEANER, 100 GPH, 250 PSI, 1.7 GPM

HP E

1S2 D250W25SD007 $5,862 1.17 0.12 0.13 50.718.47WATER BLASTER, LOW PRESSURE, STEAM CLEANER, 120 GPH, 250 PS, 2.0 GPM

HP E

1S2.7 D250W25SD008 $6,378 1.28 0.13 0.13 60.779.77WATER BLASTER, LOW PRESSURE, STEAM CLEANER, 160 GPH, 250 PSI, 2.7 GPM

HP E

5C-4-E 2000W25SD001 $5,162 1.03 0.11 0.67 40.633.88WATER BLASTER, LOW PRESSURE, COLD WATER, 2,000 PSI, 4 GPM

HP E

12C-4-G 2800W25SD005 $6,040 1.21 0.13 3.11 40.746.85WATER BLASTER, LOW PRESSURE, COLD WATER, 2,800 PSI, 4 GPM

HP G

18C-5-G 3400W25SD003 $8,004 1.60 0.17 4.66 50.979.68WATER BLASTER, LOW PRESSURE, COLD WATER, 3,400 PSI, 5 GPM

HP G

8H3.5*3000W25SD004 $11,722 2.29 0.25 2.07 61.408.81WATER BLASTER, LOW PRESSURE, HOT WATER, 3,000 PSI, 3.5 GPM, TRAILER MTD

HP G

11SF11W25SD009 $14,126 2.83 0.30 1.48 91.7216.11WATER BLASTER, LOW PRESSURE, STEAM GENERATOR, 15 PSI, 355 LB/HR STEAM, 55 GAL BOILER

HP E

3EN-140-H4-1800W25SD002 $13,322 2.66 0.28 0.40 71.618.05WATER BLASTER, LOW PRESSURE, HOT WATER, 1,800 PSI, 2.3 GPM

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-246


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT


5COLD 3/1000GW25XX005 $1,933 0.39 0.04 1.29 40.242.53WATER BLASTER, LOW PRESSURE, COLD WATER, 700 PSI, 3 GPM

HP G

5COLD 4/1000GW25XX006 $2,701 0.54 0.06 1.29 40.332.96WATER BLASTER, LOW PRESSURE, COLD WATER, 1,200 PSI, 3 GPM

HP G


HP G


HP G

8HOT 4/1000GW25XX009 $7,559 1.51 0.16 2.07 60.926.55WATER BLASTER, LOW PRESSURE, HOT WATER/STEAM, 1,000 PSI, 4 GPM

HP G

24HOT 6/3000GW25XX010 $11,579 2.32 0.24 6.21 101.4013.41WATER BLASTER, LOW PRESSURE, HOT WATER/STEAM, 3,000 PSI, 6 GPM

HP G

0.20 HIGH PRESSURE, (>= 5,000 PSI)SUBCATEGORY

NLB CORPORATION

2006200EW25NL001 $70,974 14.19 1.50 26.98 1188.6081.76WATER BLASTER, HIGH PRESSURE, 6,000 PSI, 50 GPM, SKID MTD, W/MODEL 10200 PUMP

HP E

150 201536DW25NL003 $76,551 15.31 1.62 21.40 789.2869.52WATER BLASTER, HIGH PRESSURE, 20,000 PSI, 13.2 GPM, SKID MTD, W/50 LF HOSE & CLEANING LANCE

HP D-off

33520253DW25NL002 $119,469 23.89 2.52 47.79 14014.47124.79WATER BLASTER, HIGH PRESSURE, 20,000 PSI, 22 GPM, SKID MTD (ADD TRUCK, FLATBED TRAILER & WATER TANKER)

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-247


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

W25 NLB CORPORATION (continued)70020600DW25NL005 $293,017 58.60 6.18 99.86 20035.48286.42WATER BLASTER, HIGH PRESSURE,

20,000 PSI, 53 GPM, SKID MTD (ADD TRUCK, FLATBED TRAILER & WATER TANKER)

HP D-off

344400W25NL004 $156,959 30.92 3.31 4.85 8018.7797.65WATER BLASTER, HIGH PRESSURE, HYDRODEMOLITION UNIT, CONCRETE BUSTER, SELF PROPELLED (ADD MODEL 20600D WATER BLASTER)

HP D-off

0.30 STEAM CLEANERSSUBCATEGORY

ALKOTA CLEANING SYSTEMS, INC.

1122W25AO002 $4,131 0.83 0.09 0.13 40.513.26WATER BLASTER, STEAM CLEANER, 400 PSI, 1.7 GPM

HP E


HP E


HP E


HP E

1246W25AO006 $9,252 1.85 0.20 0.13 71.136.13WATER BLASTER, STEAM GENERATOR, 100 PSI, 1.0 GPM

HP E

0.40 CO2 BLASTERSSUBCATEGORY

COLD JET

20P750BW25CJ001 $72,780 9.70 1.44 1.99 346.2929.28CARBON DIOXIDE (CO2) BLASTER/PELLETIZER, 600 LBS/HR, SINGLE HOSE DELIVERY (ADD 65-100 CFM COMPRESSOR)

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-248


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

W25 COLD JET (continued)24P1500BW25CJ002 $112,962 15.06 2.24 2.39 379.7744.34CARBON DIOXIDE (CO2)

BLASTER/PELLETIZER, 1,200 LBS/HR, SINGLE HOSE DELIVERY (ADD 65-150 CFM COMPRESSOR)

HP E

24P3000BW25CJ003 $178,566 23.81 3.54 2.39 6615.4567.89CARBON DIOXIDE (CO2) BLASTER/PELLETIZER, 1,200 LBS/HR, DUAL HOSE DELIVERY (ADD 65-200 CFM COMPRESSOR)

HP E

0.50 WET ABRASIVE BLASTING SYSTEM (TORBO)SUBCATEGORY

KEIZER TECHNOLOGIES AMERICAS, INC

350TORBO M120W25KZ001 $20,495 1.33 0.42 0.00 41.092.76WATER BLASTER, WET ABRASIVE BLASTER, 4.2 CF TANK CAP, 170 PSI, (INCLUDES HOSES & NOZZLE, ADD 350 CFM AIR COMPRESSOR)

CFM A

350TORBO M120W25KZ002 $22,690 1.47 0.47 0.00 41.213.06WATER BLASTER, WET ABRASIVE BLASTER, 4.2 CF TANK CAP, 170 PSI, W/MIX RUST INHIBITOR INJECTOR (INCLUDES HOSES & NOZZLE, ADD 350 CFM AIR COMPRESSOR)

CFM A

350LOC RESTORATION UNIT

W25KZ003 $23,196 1.51 0.48 0.00 41.243.14WATER BLASTER, WET ABRASIVE BLASTER, 4.2 CF TANK CAP, 170 PSI, W/LOC RESTORATION UNIT (INCLUDES HOSES & NOZZLE, ADD 350 CFM AIR COMPRESSOR)

CFM A

385TORBO M320W25KZ004 $33,001 2.15 0.68 0.00 81.764.46WATER BLASTER, WET ABRASIVE BLASTER, 13.0 CF TANK CAP, 170 PSI, (INCLUDES HOSES & NOZZLE, ADD 385 CFM AIR COMPRESSOR)

CFM A

EP 1110-1-8, Vol. 130 Nov 09

2-249


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

W25 KEIZER TECHNOLOGIES AMERICAS, INC (continued)

385TORBO XL320W25KZ005 $38,966 2.53 0.80 0.00 82.075.25WATER BLASTER, WET ABRASIVE BLASTER, 13.0 CF TANK CAP, 170 PSI, (INCLUDES HOSES & NOZZLE, ADD 385 CFM AIR COMPRESSOR)

CFM A

385TORBO XL320W25KZ006 $39,714 2.58 0.82 0.00 92.115.36WATER BLASTER, WET ABRASIVE BLASTER, 19.0 CF TANK CAP, 170 PSI, (INCLUDES HOSES & NOZZLE, ADD 385 CFM AIR COMPRESSOR)

CFM A

385TORBO XL320W25KZ007 $42,359 2.75 0.87 0.00 92.255.71WATER BLASTER, WET ABRASIVE BLASTER, 19.0 CF TANK CAP, 170 PSI, W/MIX RUST INHIBATOR INJECTOR,(INCLUDES HOSES & NOZZLE, ADD 385 CFM AIR COMPRESSOR)

CFM A

WATER TANKSW300.10 PORTABLE WITH WHEELSSUBCATEGORY


8EWT-8CW30SO001 $52,988 3.42 0.98 1.42 1302.699.55WATER TANK, PORTABLE, TRAILER MTD, SELF ELEVATING, 8,000 GAL, 10" PIPE

HP G


HP G


HP G

EP 1110-1-8, Vol. 130 Nov 09

2-250


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8(Vol. 1)

7/31/2009

CAT

0.20 SKID MOUNTEDSUBCATEGORY


WST-8 W30SO004 $33,932 2.26 0.63 0.00 1071.764.62WATER TANK, PORTABLE, SKID MTD, 8,000 GAL, 10" PIPE



WELDERSW350.10 ENGINE DRIVENSUBCATEGORY


11GAS 150 ACW35XX020 $2,395 0.22 0.05 2.38 20.163.20WELDER, ENGINE DRIVEN, GAS, AC, 150 AMP, 4.5 KW, PORTABLE, SKID MTD

HP G

17GAS 225 AC/DC-CC

W35XX021 $6,330 0.58 0.13 3.68 60.425.57WELDER, ENGINE DRIVEN, GAS, AC/DC-CC, 225 AMP, 5-8 KW, TRAILER MTD

HP G

18GAS 250 AC/DC-CC/CV

W35XX022 $6,523 0.59 0.13 3.90 60.435.84WELDER, ENGINE DRIVEN, GAS, AC/DC-CC/CV, 250 AMP, 9 KW, TRAILER MTD

HP G

45GAS 300 DC-CCW35XX023 $11,279 1.04 0.22 9.75 140.7413.45WELDER, ENGINE DRIVEN, GAS, DC-CC, 300 AMP, 3 KW, TRAILER MTD

HP G

48DIESEL 400 DC-CC/CV

W35XX024 $16,657 1.54 0.33 5.78 211.1010.26WELDER, ENGINE DRIVEN, DIESEL, DC-CC/CV, 400 AMP, 2-10 KW, TRAILER MTD

HP D-off

42DIESEL 500 DC-CC/CV

W35XX025 $15,973 1.48 0.32 5.06 181.069.31WELDER, ENGINE DRIVEN, DIESEL, DC-CC/CV, 500 AMP, 4 KW, TRAILER MTD

HP D-off

EP 1110-1-8, Vol. 130 Nov 09

2-251


VALUE (TEV)




ADJUSTABLE ELEMENTS


EP 1110-1-8

7/31/2009

CAT

(Vol. 1)

0.20 ELECTRIC DRIVENSUBCATEGORY

LINCOLN ELECTRIC COMPANY

5SP-180TW35LC018 $866 0.12 0.02 0.21 10.080.54WELDER, ELECTRIC DRIVEN, 30-180 AMP, WIRE FEEDER

HP E

15LINCWELD 225/125

W35LC010 $613 0.08 0.01 0.64 10.051.09WELDER, ELECTRIC DRIVEN, 225 AMP, STICK

HP E

27IDEAL ARC R3R-300

W35LC011 $3,057 0.41 0.06 1.15 40.272.48WELDER, ELECTRIC DRIVEN, 300 AMP, STICK

HP E

35IDEAL ARC R3R-400


HP E

41IDEAL ARC R3R-500


HP E

26PROCUT 80W35LC020 $3,839 0.51 0.08 1.11 10.342.62WELDER, ELECTRIC DRIVEN, 85 AMP, PLASMA CUTTING TORCH

HP E

EP 1110-1-8, Vol. 130 Nov 09

2-252

2-253

Table 2-2. Hourly Rate Elements

This Table Contains All Hourly Rate Elements as

Described in Chapter 2

For

Average and Severe Operating Conditions.

Refer to Chapter 2, Section II. Operating Condition

EP 1110-1-8, Vol. 130 Nov 09

2-253

CAT ID. NO. DEPR FCCM FUEL FOGTIRE WEAR

TIRE REPAIR REPAIR

TOTAL RATE FCCM FUEL FOG

TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR

Table 2-2 . HOURLY RATE ELEMENTS

AVERAGE OPERATING CONDITIONS SEVERE OPERATING CONDITIONS

EP 1110-1-8(Vol. 1)7/31/2009

1REGION

A10A10AR001 0.40 0.06 0.00 0.00 0.00 0.00 0.37 0.83A10AR002 1.95 0.29 0.00 0.20 0.00 0.00 1.81 4.25A10RS003 10.59 2.07 16.38 1.86 0.47 0.08 12.37 43.82A10RS004 10.66 2.08 16.38 1.86 0.47 0.08 12.45 43.98A10RS005 10.71 2.09 16.38 1.86 0.47 0.08 12.51 44.10A10RS006 10.74 2.10 16.38 1.86 0.47 0.08 12.54 44.17A10RS007 10.87 2.12 16.38 1.86 0.47 0.08 12.69 44.47A10RS008 21.05 4.10 22.09 2.51 0.71 0.12 24.55 75.13A10SE001 1.68 0.25 0.00 0.00 0.00 0.00 1.56 3.49A10SE002 1.98 0.29 0.00 0.00 0.00 0.00 1.84 4.11

A15A15IA001 1.74 0.41 6.39 0.85 0.08 0.01 2.13 11.61A15IA002 3.78 0.89 12.55 1.67 0.08 0.01 4.63 23.61A15IA003 4.51 1.07 19.86 2.64 0.14 0.02 5.53 33.77A15IA004 4.51 1.07 19.86 2.64 0.14 0.02 5.53 33.77A15IA005 4.51 1.07 19.86 2.64 0.14 0.02 5.53 33.77A15IA006 9.98 2.36 34.24 4.56 0.29 0.05 12.24 63.72A15IA007 10.47 2.48 34.24 4.56 0.29 0.05 12.83 64.92A15IA008 7.88 1.87 38.23 5.09 0.29 0.05 9.67 63.08A15IA009 7.89 1.88 35.38 4.71 0.29 0.05 9.68 59.88A15IA010 14.13 3.34 45.65 6.07 0.29 0.05 17.32 86.85A15SR002 14.94 3.54 50.21 6.68 0.43 0.07 18.32 94.19A15SR004 1.26 0.30 8.90 1.18 0.08 0.01 1.55 13.28A15SR005 1.82 0.43 9.13 1.21 0.08 0.01 2.24 14.92A15SR006 1.26 0.30 8.67 1.15 0.08 0.01 1.55 13.02A15SR007 1.26 0.30 8.79 1.17 0.08 0.01 1.55 13.16

2 192

EP 1110-1-8, Vol. 130 Nov 09

2-254


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

A15 cont.A15SR008 3.08 0.73 14.04 1.87 0.14 0.02 3.78 23.66A15SR009 3.08 0.73 14.15 1.88 0.14 0.02 3.78 23.78A15SR010 6.40 1.53 26.25 3.49 0.29 0.05 7.85 45.86A15SR011 7.55 1.79 34.24 4.56 0.29 0.05 9.26 57.74A15SR012 7.43 1.77 34.24 4.56 0.29 0.05 9.12 57.46A15SR013 13.06 3.09 51.35 6.83 0.29 0.05 16.01 90.68A15SR014 14.12 3.36 51.35 6.83 0.56 0.09 17.33 93.64A15SR015 10.53 2.52 59.91 7.97 0.56 0.09 12.93 94.51A15XX019 0.72 0.18 6.14 0.93 0.08 0.01 0.89 8.95A15XX020 1.41 0.34 3.42 0.46 0.08 0.01 1.73 7.45A15XX021 0.97 0.23 10.23 1.55 0.08 0.01 1.20 14.27A15XX022 1.44 0.35 3.99 0.53 0.08 0.01 1.77 8.17A15XX023 1.03 0.25 13.30 2.02 0.08 0.01 1.26 17.95A15XX024 1.63 0.39 5.71 0.76 0.08 0.01 2.00 10.58A15XX025 1.12 0.27 12.28 1.87 0.08 0.01 1.38 17.01A15XX026 1.83 0.44 7.99 1.06 0.08 0.01 2.24 13.65A15XX027 1.17 0.28 18.42 2.80 0.08 0.01 1.44 24.20A15XX028 1.87 0.45 9.13 1.21 0.08 0.01 2.30 15.05A15XX029 1.27 0.30 14.33 2.18 0.08 0.01 1.56 19.73A15XX030 2.48 0.59 9.70 1.29 0.08 0.01 3.05 17.20A15XX031 3.64 0.86 12.55 1.67 0.08 0.01 4.46 23.27A15XX032 3.29 0.78 13.12 1.75 0.14 0.02 4.04 23.14A15XX033 4.37 1.05 19.40 2.58 0.29 0.05 5.37 33.11A15XX034 6.09 1.45 28.53 3.80 0.29 0.05 7.48 47.69A15XX035 6.49 1.55 31.38 4.18 0.29 0.05 7.97 51.91A15XX036 7.00 1.67 31.38 4.18 0.29 0.05 8.60 53.17A15XX037 7.49 1.78 35.38 4.71 0.29 0.05 9.19 58.89

2 193

EP 1110-1-8, Vol. 130 Nov 09

2-255


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

A15 cont.A15XX038 11.42 2.70 41.08 5.47 0.29 0.05 14.01 75.02A15XX039 11.93 2.83 52.50 6.99 0.38 0.06 14.64 89.33A15XX040 12.85 3.05 57.06 7.59 0.38 0.06 15.76 96.75A15XX041 0.17 0.04 0.53 0.28 0.00 0.00 0.17 1.19A15XX042 0.22 0.06 0.75 0.40 0.00 0.00 0.22 1.65A15XX043 0.34 0.08 1.07 0.57 0.00 0.00 0.34 2.40A15XX044 0.39 0.10 1.60 0.85 0.00 0.00 0.39 3.33A15XX045 0.56 0.14 2.66 1.42 0.00 0.00 0.56 5.34A15XX046 0.69 0.17 3.20 1.71 0.00 0.00 0.69 6.46

A20A20CK001 0.23 0.03 0.00 0.00 0.00 0.00 0.50 0.76A20CK002 0.14 0.02 0.00 0.00 0.00 0.00 0.30 0.46A20CK003 0.25 0.03 0.00 0.00 0.00 0.00 0.53 0.81A20CK005 0.30 0.04 0.00 0.00 0.00 0.00 0.66 1.00A20CK006 0.17 0.02 0.00 0.00 0.00 0.00 0.36 0.55A20CK008 0.17 0.02 0.00 0.00 0.00 0.00 0.38 0.57A20CK010 0.18 0.02 0.00 0.00 0.00 0.00 0.39 0.59A20CM010 0.58 0.07 0.00 0.06 0.00 0.00 1.26 1.97A20CM011 0.75 0.09 0.00 0.06 0.00 0.00 1.62 2.52A20CM012 0.84 0.10 0.00 0.13 0.00 0.00 1.82 2.89A20CM013 2.45 0.32 0.00 0.28 0.11 0.02 5.35 8.53A20CM014 2.88 0.40 0.00 0.41 0.39 0.07 6.34 10.49A20CM015 3.42 0.46 0.00 0.50 0.26 0.04 7.49 12.17A20CM016 2.21 0.27 0.00 0.30 0.00 0.00 4.80 7.58A20CM017 0.10 0.01 0.00 0.00 0.00 0.00 0.22 0.33A20CM018 0.11 0.01 0.00 0.00 0.00 0.00 0.24 0.36A20CM019 0.14 0.01 0.00 0.00 0.00 0.00 0.31 0.46

2 194

EP 1110-1-8, Vol. 130 Nov 09

2-256


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

A20 cont.A20CM020 0.11 0.01 0.00 0.00 0.00 0.00 0.26 0.38A20WC002 0.16 0.02 0.18 0.24 0.00 0.00 0.36 0.96A20WC004 0.48 0.06 0.71 0.11 0.00 0.00 1.04 2.40A20XX001 0.35 0.03 0.00 0.00 0.00 0.00 0.73 1.11A20XX002 0.41 0.03 0.00 0.00 0.00 0.00 0.84 1.28A20XX003 0.51 0.04 0.00 0.00 0.00 0.00 1.05 1.60A20XX004 0.67 0.05 0.00 0.00 0.00 0.00 1.37 2.09A20XX005 0.94 0.07 0.00 0.00 0.00 0.00 1.94 2.95A20XX006 1.16 0.09 0.00 0.00 0.00 0.00 2.38 3.63A20XX007 1.43 0.11 0.00 0.00 0.00 0.00 2.94 4.48A20XX008 1.91 0.14 0.00 0.00 0.00 0.00 3.93 5.98A20XX021 0.18 0.02 0.00 0.00 0.00 0.00 0.39 0.59A20XX022 0.21 0.03 0.00 0.00 0.00 0.00 0.46 0.70A20XX023 0.25 0.03 0.00 0.00 0.00 0.00 0.55 0.83A20XX024 0.26 0.03 0.00 0.00 0.00 0.00 0.57 0.86A20XX025 0.37 0.05 0.00 0.00 0.00 0.00 0.81 1.23

A25A25RS006 8.91 1.11 0.00 1.16 0.00 0.00 10.43 21.61A25RS008 10.22 1.27 0.00 1.80 0.00 0.00 11.96 25.25A25XX001 7.52 0.94 0.00 0.64 0.00 0.00 8.81 17.91A25XX002 8.76 1.09 0.00 1.51 0.00 0.00 10.26 21.62A25XX003 9.59 1.19 0.00 2.09 0.00 0.00 11.23 24.10

A30A30BG003 39.44 7.25 17.03 3.77 3.80 0.64 58.00 129.93A30BG004 35.86 6.26 12.07 3.11 0.00 0.00 52.32 109.62A30BG005 41.59 7.26 17.03 3.77 0.00 0.00 60.67 130.32

2 195

EP 1110-1-8, Vol. 130 Nov 09

2-257


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

A30 cont.A30BG007 30.81 5.56 10.56 2.91 2.17 0.36 45.17 97.54A30BG009 33.33 6.03 14.98 1.99 2.56 0.43 48.88 108.20A30BK010 15.83 2.88 5.07 0.67 1.67 0.28 23.24 49.64A30BK011 28.02 5.07 11.53 1.53 2.17 0.36 41.11 89.79A30BK013 29.69 5.35 15.63 2.08 1.95 0.33 43.52 98.55A30BK015 34.03 6.15 19.83 2.64 2.56 0.43 49.91 115.55A30BK017 37.20 6.50 19.83 2.64 0.00 0.00 54.26 120.43A30BK018 38.29 6.69 19.83 2.64 0.00 0.00 55.87 123.32A30BK019 22.27 3.95 11.32 1.51 0.58 0.10 32.56 72.29A30BK020 28.77 5.08 18.65 2.48 0.70 0.12 42.05 97.85A30BK021 37.69 6.58 18.97 2.52 0.00 0.00 54.98 120.74A30BK022 27.72 5.01 15.63 2.08 1.95 0.33 40.65 93.37A30BK023 32.35 5.65 15.63 2.08 0.00 0.00 47.19 102.90A30BK024 26.94 6.46 18.08 2.41 1.41 0.24 33.56 89.10A30CA002 29.00 5.24 11.53 1.53 1.95 0.33 42.53 92.11A30CA007 9.30 2.25 10.51 1.40 0.65 0.11 11.60 35.82A30CA008 33.76 6.09 18.75 2.49 2.45 0.41 49.50 113.45A30CA009 42.86 7.48 18.65 2.48 0.00 0.00 62.52 133.99A30CA013 30.25 5.28 13.04 1.74 0.00 0.00 44.13 94.44A30CA014 30.37 5.51 16.49 2.19 2.56 0.43 44.57 102.12A30CA015 50.67 8.85 18.75 2.49 0.00 0.00 73.92 154.68A30CA016 39.28 6.86 18.65 2.48 0.00 0.00 57.31 124.58A30CH001 26.89 4.88 11.86 1.58 2.17 0.36 39.45 87.19A30CH002 29.46 5.31 16.38 2.18 1.95 0.33 43.19 98.80A30CH003 30.66 5.35 16.38 2.18 0.00 0.00 44.72 99.29A30CH004 31.01 5.60 16.38 2.18 2.07 0.35 45.47 103.06A30CH005 33.86 6.11 18.65 2.48 2.45 0.41 49.64 113.60

2 196

EP 1110-1-8, Vol. 130 Nov 09

2-258


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

A30 cont.A30CH006 40.78 7.12 21.56 2.87 0.00 0.00 59.49 131.82A30GC002 3.95 0.70 2.69 0.36 0.17 0.03 5.78 13.68A30GC004 5.79 1.01 4.42 0.59 0.00 0.00 8.45 20.26A30LD001 10.70 2.63 10.81 1.44 1.23 0.21 13.40 40.42A30MP001 10.53 2.47 7.86 1.05 0.00 0.00 13.05 34.96A30MP002 13.67 3.21 9.83 1.31 0.00 0.00 16.96 44.98A30RT001 39.66 9.31 27.02 3.60 0.08 0.01 49.18 128.86A30RT002 41.59 9.77 27.02 3.60 0.17 0.03 51.59 133.77A30XX001 9.45 2.66 10.11 1.13 0.63 0.11 8.08 32.17A30XX002 11.74 3.26 10.11 1.13 0.00 0.00 10.01 36.25

A35A35AE001 1.27 0.20 0.89 2.09 0.07 0.01 1.60 6.13A35AE002 1.32 0.21 0.89 2.79 0.07 0.01 1.65 6.94A35AE003 1.44 0.22 0.89 3.14 0.05 0.01 1.80 7.55A35AE004 1.59 0.24 0.89 4.04 0.05 0.01 1.98 8.80A35AE005 1.70 0.27 0.89 6.24 0.09 0.02 2.13 11.34

A40A40CA008 63.52 9.44 71.33 9.49 0.00 0.00 98.45 252.23A40CA009 89.37 13.28 89.16 11.86 0.00 0.00 138.52 342.19A40CW001 105.39 15.66 135.52 18.03 0.00 0.00 163.36 437.96A40RT001 41.83 6.44 32.81 4.37 1.81 0.30 65.29 152.85A40RT002 56.60 8.41 35.66 4.74 0.00 0.00 87.72 193.13A40RT003 69.65 10.35 65.62 8.73 0.00 0.00 107.96 262.31A40RT005 95.58 14.20 114.12 15.18 0.00 0.00 148.15 387.23A40RT006 105.86 15.73 114.12 15.18 0.00 0.00 164.08 414.97

2 197

EP 1110-1-8, Vol. 130 Nov 09

2-259


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

A45A45AE001 1.38 0.18 0.00 7.10 0.04 0.01 1.95 10.66A45AE002 2.74 0.36 0.00 14.25 0.04 0.01 3.84 21.24A45AE003 3.24 0.42 0.00 16.85 0.04 0.01 4.54 25.10A45RS001 7.41 0.95 7.86 1.55 0.07 0.01 10.36 28.21A45RS002 24.06 3.06 24.15 3.71 0.00 0.00 33.56 88.54A45SE003 5.82 0.75 2.95 2.39 0.11 0.02 8.14 20.18A45SE004 3.60 0.48 2.31 0.85 0.14 0.02 5.07 12.47

B10B10CC007 4.54 0.89 3.20 3.49 0.13 0.02 7.08 19.35B10CC008 12.37 2.43 28.95 7.90 0.64 0.11 19.28 71.68B10CC009 13.76 2.74 35.52 9.14 1.12 0.19 21.49 83.96B10CC010 14.87 2.95 35.52 9.39 1.12 0.19 23.22 87.26B10CC011 2.15 0.41 1.85 1.99 0.00 0.00 3.34 9.74B10CC012 2.12 0.41 3.20 1.24 0.00 0.00 3.29 10.26B10CC013 2.56 0.49 3.20 1.29 0.00 0.00 3.97 11.51B10CC014 0.66 0.13 0.46 0.75 0.00 0.00 1.03 3.03B10CL005 29.02 5.67 11.08 7.92 0.75 0.13 45.16 99.73B10CL006 29.51 5.76 11.08 7.92 0.75 0.13 45.92 101.07B10CL015 15.27 3.03 2.77 3.98 0.70 0.12 23.83 49.70B10CL021 8.15 1.62 3.23 1.73 0.41 0.07 12.73 27.94B10CL025 27.13 5.23 18.46 9.86 0.22 0.04 42.11 103.05B10CL027 2.12 0.41 0.00 0.00 0.00 0.00 3.28 5.81B10CL032 0.42 0.08 0.92 0.49 0.00 0.00 0.65 2.56B10CL034 0.84 0.16 1.85 0.99 0.00 0.00 1.30 5.14B10CL036 0.35 0.07 0.74 0.40 0.00 0.00 0.54 2.10B10CL040 0.48 0.09 1.85 0.99 0.00 0.00 0.75 4.16

2 198

EP 1110-1-8, Vol. 130 Nov 09

2-260


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

B10 cont.B10CL042 0.32 0.06 0.46 0.25 0.00 0.00 0.49 1.58B10CL045 0.41 0.08 0.92 0.49 0.00 0.00 0.63 2.53B10EM001 41.67 8.16 4.44 3.17 1.24 0.21 64.88 123.77B10EM002 2.69 0.57 0.92 1.49 0.35 0.06 4.25 10.33B10EM003 2.76 0.53 0.00 0.00 0.00 0.00 4.28 7.57B10KB001 13.34 3.19 8.77 4.69 0.45 0.08 20.75 51.27B10KB002 23.91 5.67 20.31 10.85 0.50 0.08 37.15 98.47B10RC006 18.56 3.67 4.20 6.74 0.77 0.13 28.95 63.02B10RC007 14.48 2.84 1.38 3.24 0.47 0.08 22.56 45.05B10RC008 15.70 3.08 2.77 3.98 0.47 0.08 24.45 50.53B10RC016 22.94 4.51 6.92 9.20 0.77 0.13 35.74 80.21B10RC027 14.55 2.79 3.69 3.97 0.00 0.00 22.55 47.55B10RC028 16.34 3.13 5.54 5.21 0.00 0.00 25.33 55.55B10RC029 18.47 3.54 7.38 6.44 0.00 0.00 28.63 64.46B10RC030 20.13 3.86 9.23 8.68 0.00 0.00 31.20 73.10B10RC031 21.25 4.07 11.08 9.92 0.00 0.00 32.94 79.26B10RC032 20.11 3.97 4.62 6.97 0.77 0.13 31.36 67.93B10SN031 6.89 1.44 2.31 2.58 0.85 0.14 10.88 25.09B10SN032 10.84 2.20 2.77 3.23 0.86 0.14 17.01 37.05B10SN033 13.44 2.70 2.77 2.98 0.84 0.14 21.04 43.91B10SN034 14.62 2.93 1.85 2.49 0.86 0.14 22.87 45.76B10SN035 15.38 3.07 2.77 3.13 0.86 0.14 24.04 49.39B10SN036 14.35 2.88 4.15 3.97 0.86 0.14 22.45 48.80

B15B15BM001 4.99 0.80 7.86 1.05 0.00 0.00 5.47 20.17B15EC001 20.56 3.33 8.60 1.14 0.62 0.10 22.58 56.93B15EC002 13.63 2.21 9.83 1.31 0.32 0.05 14.97 42.32

2 199

EP 1110-1-8, Vol. 130 Nov 09

2-261


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

B15 cont.B15EC003 19.54 3.13 22.60 3.01 0.10 0.02 21.43 69.83B15MB001 0.88 0.14 0.00 0.10 0.00 0.00 0.97 2.09B15MB002 1.07 0.17 0.00 0.14 0.00 0.00 1.17 2.55B15MB003 1.50 0.25 0.00 0.24 0.08 0.01 1.65 3.73B15MB004 1.74 0.29 3.20 0.36 0.08 0.01 1.91 7.59B15RS001 4.35 0.70 7.86 1.05 0.11 0.02 4.78 18.87B15RS005 5.65 0.92 7.86 1.05 0.17 0.03 6.21 21.89B15TB001 2.46 0.40 3.64 0.48 0.12 0.02 2.70 9.82B15TB002 2.48 0.40 3.64 0.48 0.12 0.02 2.72 9.86B15WD001 3.90 0.63 7.86 1.05 0.11 0.02 4.28 17.85B15WD002 4.04 0.65 7.86 1.05 0.11 0.02 4.44 18.17

B20B20BN001 1.22 0.20 4.44 0.67 0.03 0.01 1.51 8.08B20BN002 1.95 0.32 12.61 1.92 0.06 0.01 2.41 19.28B20BN003 2.47 0.40 24.86 3.78 0.07 0.01 3.05 34.64B20BN005 2.12 0.35 12.43 1.89 0.07 0.01 2.62 19.49B20BN006 2.35 0.38 21.13 3.21 0.07 0.01 2.91 30.06B20BN007 4.25 0.70 12.28 1.63 0.20 0.03 5.26 24.35B20MQ001 2.43 0.39 8.45 1.12 0.02 0.00 3.00 15.41B20MQ003 3.36 0.54 13.76 1.83 0.07 0.01 4.16 23.73B20MQ004 3.85 0.64 24.57 3.27 0.23 0.04 4.77 37.37B20MQ005 42.36 6.83 63.88 10.00 0.57 0.10 52.34 176.08

B25B25HB001 2.10 0.34 0.00 0.00 0.00 0.00 1.93 4.37 2.59 0.35 0.00 0.00 0.00 0.00 2.72 5.66B25HB003 3.38 0.54 0.00 0.00 0.00 0.00 3.10 7.02 4.16 0.55 0.00 0.00 0.00 0.00 4.36 9.07B25HB005 4.39 0.70 0.00 0.00 0.00 0.00 4.03 9.12 5.40 0.72 0.00 0.00 0.00 0.00 5.67 11.79

2 200

EP 1110-1-8, Vol. 130 Nov 09

2-262


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

B25 cont.B25HB007 5.18 0.83 0.00 0.00 0.00 0.00 4.76 10.77 6.37 0.85 0.00 0.00 0.00 0.00 6.69 13.91B25HB008 6.04 0.96 0.00 0.00 0.00 0.00 5.55 12.55 7.43 0.99 0.00 0.00 0.00 0.00 7.80 16.22B25HB009 6.65 1.06 0.00 0.00 0.00 0.00 6.11 13.82 8.18 1.09 0.00 0.00 0.00 0.00 8.59 17.86B25HB010 7.01 1.12 0.00 0.00 0.00 0.00 6.44 14.57 8.62 1.15 0.00 0.00 0.00 0.00 9.05 18.82B25HB011 7.20 1.15 0.00 0.00 0.00 0.00 6.61 14.96 8.86 1.18 0.00 0.00 0.00 0.00 9.30 19.34B25HB012 7.61 1.22 0.00 0.00 0.00 0.00 7.00 15.83 9.37 1.25 0.00 0.00 0.00 0.00 9.84 20.46B25HB013 7.86 1.26 0.00 0.00 0.00 0.00 7.23 16.35 9.68 1.29 0.00 0.00 0.00 0.00 10.16 21.13B25HB014 8.21 1.31 0.00 0.00 0.00 0.00 7.55 17.07 10.11 1.35 0.00 0.00 0.00 0.00 10.62 22.08B25HB015 8.51 1.36 0.00 0.00 0.00 0.00 7.82 17.69 10.48 1.40 0.00 0.00 0.00 0.00 11.00 22.88B25XX001 0.95 0.15 0.00 0.00 0.00 0.00 0.87 1.97 1.17 0.16 0.00 0.00 0.00 0.00 1.23 2.56B25XX002 1.41 0.23 0.00 0.00 0.00 0.00 1.29 2.93 1.73 0.23 0.00 0.00 0.00 0.00 1.82 3.78B25XX003 1.74 0.28 0.00 0.00 0.00 0.00 1.60 3.62 2.14 0.29 0.00 0.00 0.00 0.00 2.24 4.67B25XX004 1.90 0.30 0.00 0.00 0.00 0.00 1.75 3.95 2.34 0.31 0.00 0.00 0.00 0.00 2.46 5.11B25XX005 2.22 0.35 0.00 0.00 0.00 0.00 2.04 4.61 2.73 0.36 0.00 0.00 0.00 0.00 2.86 5.95B25XX006 2.50 0.40 0.00 0.00 0.00 0.00 2.29 5.19 3.07 0.41 0.00 0.00 0.00 0.00 3.23 6.71B25XX007 2.66 0.43 0.00 0.00 0.00 0.00 2.45 5.54 3.28 0.44 0.00 0.00 0.00 0.00 3.44 7.16B25XX008 3.11 0.50 0.00 0.00 0.00 0.00 2.86 6.47 3.83 0.51 0.00 0.00 0.00 0.00 4.02 8.36B25XX009 3.27 0.52 0.00 0.00 0.00 0.00 3.01 6.80 4.03 0.54 0.00 0.00 0.00 0.00 4.23 8.80B25XX010 3.48 0.56 0.00 0.00 0.00 0.00 3.20 7.24 4.29 0.57 0.00 0.00 0.00 0.00 4.50 9.36B25XX011 3.65 0.58 0.00 0.00 0.00 0.00 3.36 7.59 4.50 0.60 0.00 0.00 0.00 0.00 4.72 9.82B25XX012 4.08 0.65 0.00 0.00 0.00 0.00 3.75 8.48 5.02 0.67 0.00 0.00 0.00 0.00 5.27 10.96B25XX013 5.49 0.88 0.00 0.00 0.00 0.00 5.04 11.41 6.76 0.90 0.00 0.00 0.00 0.00 7.09 14.75B25XX014 5.86 0.94 0.00 0.00 0.00 0.00 5.38 12.18 7.21 0.96 0.00 0.00 0.00 0.00 7.57 15.74B25XX015 7.07 1.13 0.00 0.00 0.00 0.00 6.50 14.70 8.71 1.16 0.00 0.00 0.00 0.00 9.14 19.01B25XX016 7.13 1.14 0.00 0.00 0.00 0.00 6.56 14.83 8.78 1.17 0.00 0.00 0.00 0.00 9.22 19.17B25XX017 7.70 1.23 0.00 0.00 0.00 0.00 7.08 16.01 9.48 1.26 0.00 0.00 0.00 0.00 9.96 20.70B25XX018 7.31 1.17 0.00 0.00 0.00 0.00 6.72 15.20 9.00 1.20 0.00 0.00 0.00 0.00 9.45 19.65

2 201

EP 1110-1-8, Vol. 130 Nov 09

2-263


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

B25 cont.B25XX019 8.18 1.31 0.00 0.00 0.00 0.00 7.52 17.01 10.07 1.34 0.00 0.00 0.00 0.00 10.57 21.98

B30B30CR001 0.57 0.08 0.00 0.00 0.00 0.00 0.56 1.21B30CR002 0.61 0.09 0.00 0.00 0.00 0.00 0.60 1.30B30CR003 0.66 0.10 0.00 0.00 0.00 0.00 0.65 1.41B30CR004 0.68 0.10 0.00 0.00 0.00 0.00 0.67 1.45B30CR005 0.80 0.12 0.00 0.00 0.00 0.00 0.79 1.71B30CR006 0.94 0.14 0.00 0.00 0.00 0.00 0.93 2.01B30CR009 0.84 0.12 0.00 0.00 0.00 0.00 0.84 1.80B30CR010 0.98 0.14 0.00 0.00 0.00 0.00 0.97 2.09B30CR011 1.16 0.17 0.00 0.00 0.00 0.00 1.15 2.48B30CR012 1.34 0.20 0.00 0.00 0.00 0.00 1.33 2.87B30GB001 0.48 0.07 0.00 0.00 0.00 0.00 0.41 0.96B30GB002 0.62 0.09 0.00 0.00 0.00 0.00 0.54 1.25B30GB003 0.77 0.11 0.00 0.00 0.00 0.00 0.67 1.55B30GB004 1.11 0.16 0.00 0.00 0.00 0.00 0.97 2.24B30GB005 1.33 0.19 0.00 0.00 0.00 0.00 1.15 2.67B30GB006 2.45 0.36 0.00 0.00 0.00 0.00 2.28 5.09B30GB007 2.65 0.39 0.00 0.00 0.00 0.00 2.47 5.51B30GB008 2.94 0.43 0.00 0.00 0.00 0.00 2.74 6.11B30GB009 3.36 0.49 0.00 0.00 0.00 0.00 3.13 6.98B30GB010 4.15 0.61 0.00 0.00 0.00 0.00 3.87 8.63B30GB011 1.94 0.28 0.00 0.00 0.00 0.00 1.93 4.15B30GB012 2.01 0.29 0.00 0.00 0.00 0.00 2.00 4.30B30GB013 2.08 0.31 0.00 0.00 0.00 0.00 2.07 4.46B30GB014 2.74 0.40 0.00 0.00 0.00 0.00 2.73 5.87B30GB015 2.84 0.42 0.00 0.00 0.00 0.00 2.82 6.08

2 202

EP 1110-1-8, Vol. 130 Nov 09

2-264


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

B30 cont.B30GB016 4.08 0.60 0.00 0.00 0.00 0.00 4.06 8.74B30GB017 4.91 0.72 0.00 0.00 0.00 0.00 4.88 10.51B30GB018 0.38 0.06 0.00 0.00 0.00 0.00 0.33 0.77

B35B35HE001 0.87 0.14 0.00 0.00 0.00 0.00 0.80 1.81 1.07 0.14 0.00 0.00 0.00 0.00 1.12 2.33B35HE002 1.01 0.16 0.00 0.00 0.00 0.00 0.93 2.10 1.25 0.17 0.00 0.00 0.00 0.00 1.31 2.73B35HE003 1.44 0.23 0.00 0.00 0.00 0.00 1.32 2.99 1.77 0.24 0.00 0.00 0.00 0.00 1.86 3.87B35HE004 1.73 0.28 0.00 0.00 0.00 0.00 1.59 3.60 2.14 0.28 0.00 0.00 0.00 0.00 2.24 4.66B35HE005 1.99 0.32 0.00 0.00 0.00 0.00 1.83 4.14 2.45 0.33 0.00 0.00 0.00 0.00 2.57 5.35B35HE006 2.48 0.40 0.00 0.00 0.00 0.00 2.28 5.16 3.05 0.41 0.00 0.00 0.00 0.00 3.20 6.66B35HE007 2.69 0.43 0.00 0.00 0.00 0.00 2.48 5.60 3.32 0.44 0.00 0.00 0.00 0.00 3.48 7.24B35HE008 3.54 0.57 0.00 0.00 0.00 0.00 3.25 7.36 4.35 0.58 0.00 0.00 0.00 0.00 4.57 9.50B35HE009 3.71 0.59 0.00 0.00 0.00 0.00 3.41 7.71 4.57 0.61 0.00 0.00 0.00 0.00 4.79 9.97B35HE010 4.29 0.69 0.00 0.00 0.00 0.00 3.94 8.92 5.28 0.70 0.00 0.00 0.00 0.00 5.55 11.53B35HE011 4.65 0.74 0.00 0.00 0.00 0.00 4.27 9.66 5.72 0.76 0.00 0.00 0.00 0.00 6.00 12.48B35HE012 5.08 0.81 0.00 0.00 0.00 0.00 4.67 10.56 6.26 0.83 0.00 0.00 0.00 0.00 6.57 13.66B35HE013 5.63 0.90 0.00 0.00 0.00 0.00 5.18 11.71 6.93 0.92 0.00 0.00 0.00 0.00 7.28 15.13B35HE014 6.44 1.03 0.00 0.00 0.00 0.00 5.92 13.39 7.93 1.06 0.00 0.00 0.00 0.00 8.33 17.32B35HE015 7.00 1.12 0.00 0.00 0.00 0.00 6.44 14.56 8.62 1.15 0.00 0.00 0.00 0.00 9.05 18.82B35HE016 8.37 1.34 0.00 0.00 0.00 0.00 7.69 17.40 10.30 1.37 0.00 0.00 0.00 0.00 10.81 22.48B35HE017 9.63 1.54 0.00 0.00 0.00 0.00 8.85 20.02 11.85 1.58 0.00 0.00 0.00 0.00 12.44 25.87B35HE018 0.83 0.15 0.00 0.00 0.00 0.00 0.76 1.74 1.07 0.15 0.00 0.00 0.00 0.00 1.12 2.34B35HE019 0.95 0.17 0.00 0.00 0.00 0.00 0.87 1.99 1.22 0.17 0.00 0.00 0.00 0.00 1.29 2.68B35HE020 1.36 0.24 0.00 0.00 0.00 0.00 1.25 2.85 1.75 0.25 0.00 0.00 0.00 0.00 1.83 3.83B35HE021 1.72 0.30 0.00 0.00 0.00 0.00 1.58 3.60 2.21 0.31 0.00 0.00 0.00 0.00 2.32 4.84B35HE022 1.98 0.35 0.00 0.00 0.00 0.00 1.82 4.15 2.54 0.36 0.00 0.00 0.00 0.00 2.67 5.57B35HE023 2.36 0.42 0.00 0.00 0.00 0.00 2.17 4.95 3.04 0.43 0.00 0.00 0.00 0.00 3.19 6.66

2 203

EP 1110-1-8, Vol. 130 Nov 09

2-265


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

B35 cont.B35HE024 2.61 0.46 0.00 0.00 0.00 0.00 2.40 5.47 3.35 0.48 0.00 0.00 0.00 0.00 3.52 7.35B35HE025 3.38 0.60 0.00 0.00 0.00 0.00 3.10 7.08 4.34 0.62 0.00 0.00 0.00 0.00 4.56 9.52B35HE026 3.45 0.61 0.00 0.00 0.00 0.00 3.17 7.23 4.44 0.63 0.00 0.00 0.00 0.00 4.66 9.73B35HE027 4.18 0.74 0.00 0.00 0.00 0.00 3.84 8.76 5.38 0.76 0.00 0.00 0.00 0.00 5.64 11.78B35HE028 4.32 0.77 0.00 0.00 0.00 0.00 3.97 9.06 5.56 0.79 0.00 0.00 0.00 0.00 5.84 12.19B35HE029 4.98 0.88 0.00 0.00 0.00 0.00 4.58 10.44 6.41 0.91 0.00 0.00 0.00 0.00 6.73 14.05B35HE030 5.49 0.97 0.00 0.00 0.00 0.00 5.05 11.51 7.06 1.00 0.00 0.00 0.00 0.00 7.42 15.48B35HE031 6.68 1.18 0.00 0.00 0.00 0.00 6.14 14.00 8.59 1.22 0.00 0.00 0.00 0.00 9.02 18.83B35HE032 7.12 1.26 0.00 0.00 0.00 0.00 6.54 14.92 9.16 1.30 0.00 0.00 0.00 0.00 9.61 20.07B35HE033 9.07 1.61 0.00 0.00 0.00 0.00 8.34 19.02 11.67 1.66 0.00 0.00 0.00 0.00 12.25 25.58B35HE034 10.11 1.79 0.00 0.00 0.00 0.00 9.29 21.19 13.00 1.85 0.00 0.00 0.00 0.00 13.65 28.50B35HE035 2.79 0.54 0.00 0.00 0.00 0.00 2.57 5.90 3.49 0.56 0.00 0.00 0.00 0.00 3.67 7.72B35HE036 2.92 0.57 0.00 0.00 0.00 0.00 2.68 6.17 3.64 0.58 0.00 0.00 0.00 0.00 3.83 8.05B35HE037 3.28 0.64 0.00 0.00 0.00 0.00 3.01 6.93 4.10 0.66 0.00 0.00 0.00 0.00 4.31 9.07B35HE038 4.45 0.87 0.00 0.00 0.00 0.00 4.09 9.41 5.57 0.89 0.00 0.00 0.00 0.00 5.85 12.31B35HE039 4.98 0.97 0.00 0.00 0.00 0.00 4.58 10.53 6.23 1.00 0.00 0.00 0.00 0.00 6.54 13.77B35HE040 5.14 1.00 0.00 0.00 0.00 0.00 4.73 10.87 6.43 1.03 0.00 0.00 0.00 0.00 6.75 14.21B35HE041 5.51 1.07 0.00 0.00 0.00 0.00 5.06 11.64 6.88 1.10 0.00 0.00 0.00 0.00 7.23 15.21B35HE042 7.09 1.38 0.00 0.00 0.00 0.00 6.51 14.98 8.86 1.42 0.00 0.00 0.00 0.00 9.30 19.58B35HE043 7.29 1.42 0.00 0.00 0.00 0.00 6.70 15.41 9.11 1.46 0.00 0.00 0.00 0.00 9.57 20.14B35HE044 9.48 1.84 0.00 0.00 0.00 0.00 8.71 20.03 11.85 1.89 0.00 0.00 0.00 0.00 12.44 26.18B35HE045 9.81 1.91 0.00 0.00 0.00 0.00 9.01 20.73 12.26 1.96 0.00 0.00 0.00 0.00 12.88 27.10B35HE046 11.67 2.27 0.00 0.00 0.00 0.00 10.72 24.66 14.58 2.33 0.00 0.00 0.00 0.00 15.31 32.22B35HE047 12.42 2.42 0.00 0.00 0.00 0.00 11.41 26.25 15.52 2.48 0.00 0.00 0.00 0.00 16.30 34.30B35SA001 2.17 0.35 0.00 0.00 0.00 0.00 1.99 4.51 2.67 0.36 0.00 0.00 0.00 0.00 2.80 5.83B35SA003 3.25 0.52 0.00 0.00 0.00 0.00 2.99 6.76 4.00 0.53 0.00 0.00 0.00 0.00 4.20 8.73B35SA004 4.46 0.71 0.00 0.00 0.00 0.00 4.09 9.26 5.48 0.73 0.00 0.00 0.00 0.00 5.76 11.97

2 204

EP 1110-1-8, Vol. 130 Nov 09

2-266


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

B35 cont.B35SA005 5.58 0.89 0.00 0.00 0.00 0.00 5.13 11.60 6.87 0.92 0.00 0.00 0.00 0.00 7.22 15.01B35SA006 6.58 1.05 0.00 0.00 0.00 0.00 6.05 13.68 8.10 1.08 0.00 0.00 0.00 0.00 8.51 17.69B35SA007 7.41 1.18 0.00 0.00 0.00 0.00 6.81 15.40 9.12 1.22 0.00 0.00 0.00 0.00 9.57 19.91B35SA008 8.74 1.40 0.00 0.00 0.00 0.00 8.03 18.17 10.76 1.43 0.00 0.00 0.00 0.00 11.29 23.48B35SA009 11.09 1.77 0.00 0.00 0.00 0.00 10.19 23.05 13.65 1.82 0.00 0.00 0.00 0.00 14.33 29.80B35SA010 13.54 2.16 0.00 0.00 0.00 0.00 12.44 28.14 16.66 2.22 0.00 0.00 0.00 0.00 17.50 36.38B35XX001 3.44 0.55 0.00 0.00 0.00 0.00 3.16 7.15 4.23 0.56 0.00 0.00 0.00 0.00 4.44 9.23B35XX002 3.87 0.62 0.00 0.00 0.00 0.00 3.55 8.04 4.76 0.63 0.00 0.00 0.00 0.00 5.00 10.39B35XX003 4.28 0.68 0.00 0.00 0.00 0.00 3.93 8.89 5.26 0.70 0.00 0.00 0.00 0.00 5.53 11.49B35XX004 4.88 0.78 0.00 0.00 0.00 0.00 4.48 10.14 6.00 0.80 0.00 0.00 0.00 0.00 6.30 13.10B35XX005 5.48 0.88 0.00 0.00 0.00 0.00 5.03 11.39 6.74 0.90 0.00 0.00 0.00 0.00 7.08 14.72B35XX006 6.74 1.08 0.00 0.00 0.00 0.00 6.19 14.01 8.29 1.11 0.00 0.00 0.00 0.00 8.70 18.10B35XX007 3.45 0.61 0.00 0.00 0.00 0.00 3.17 7.23 4.44 0.63 0.00 0.00 0.00 0.00 4.66 9.73B35XX008 3.95 0.70 0.00 0.00 0.00 0.00 3.63 8.28 5.08 0.72 0.00 0.00 0.00 0.00 5.33 11.13B35XX009 4.25 0.75 0.00 0.00 0.00 0.00 3.91 8.91 5.47 0.78 0.00 0.00 0.00 0.00 5.74 11.99B35XX010 5.06 0.90 0.00 0.00 0.00 0.00 4.65 10.61 6.51 0.92 0.00 0.00 0.00 0.00 6.83 14.26B35XX011 5.60 0.99 0.00 0.00 0.00 0.00 5.14 11.73 7.20 1.02 0.00 0.00 0.00 0.00 7.55 15.77B35XX012 7.09 1.26 0.00 0.00 0.00 0.00 6.52 14.87 9.12 1.30 0.00 0.00 0.00 0.00 9.57 19.99B35XX013 0.78 0.15 0.00 0.00 0.00 0.00 0.72 1.65 0.98 0.16 0.00 0.00 0.00 0.00 1.03 2.17B35XX014 0.88 0.17 0.00 0.00 0.00 0.00 0.81 1.86 1.10 0.18 0.00 0.00 0.00 0.00 1.16 2.44B35XX015 1.31 0.25 0.00 0.00 0.00 0.00 1.20 2.76 1.64 0.26 0.00 0.00 0.00 0.00 1.72 3.62B35XX016 1.49 0.29 0.00 0.00 0.00 0.00 1.37 3.15 1.87 0.30 0.00 0.00 0.00 0.00 1.96 4.13B35XX017 1.63 0.32 0.00 0.00 0.00 0.00 1.50 3.45 2.04 0.33 0.00 0.00 0.00 0.00 2.14 4.51B35XX018 3.49 0.68 0.00 0.00 0.00 0.00 3.21 7.38 4.36 0.70 0.00 0.00 0.00 0.00 4.58 9.64B35XX019 3.73 0.73 0.00 0.00 0.00 0.00 3.43 7.89 4.66 0.74 0.00 0.00 0.00 0.00 4.89 10.29B35XX020 4.21 0.82 0.00 0.00 0.00 0.00 3.87 8.90 5.26 0.84 0.00 0.00 0.00 0.00 5.52 11.62B35XX021 4.58 0.89 0.00 0.00 0.00 0.00 4.21 9.68 5.73 0.92 0.00 0.00 0.00 0.00 6.01 12.66

2 205

EP 1110-1-8, Vol. 130 Nov 09

2-267


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

B35 cont.B35XX022 5.78 1.12 0.00 0.00 0.00 0.00 5.31 12.21 7.22 1.15 0.00 0.00 0.00 0.00 7.58 15.95B35XX023 6.19 1.21 0.00 0.00 0.00 0.00 5.69 13.09 7.74 1.24 0.00 0.00 0.00 0.00 8.13 17.11

C05C05OL001 0.15 0.01 0.56 0.09 0.00 0.00 0.52 1.33C05OL002 0.24 0.01 1.15 0.17 0.00 0.00 0.83 2.40C05OL003 0.29 0.02 1.27 0.19 0.00 0.00 1.00 2.77C05OL004 0.32 0.02 1.39 0.21 0.00 0.00 1.09 3.03

C10C10BO001 1.08 0.09 0.73 0.08 0.00 0.00 1.69 3.67C10BO003 0.59 0.05 0.98 0.11 0.00 0.00 0.92 2.65C10BO004 0.66 0.05 1.46 0.17 0.00 0.00 1.02 3.36C10BO007 2.68 0.22 0.55 0.06 0.00 0.00 4.17 7.68C10BO008 3.65 0.30 1.23 0.14 0.00 0.00 5.68 11.00C10BO009 1.37 0.13 0.98 0.11 0.00 0.00 2.38 4.97C10BO011 3.66 0.36 1.09 0.12 0.00 0.00 6.38 11.61C10BO013 9.67 0.94 2.59 0.29 0.00 0.00 16.85 30.34C10BO015 3.14 0.31 0.68 0.08 0.00 0.00 5.48 9.69C10BO016 4.59 0.45 1.23 0.14 0.00 0.00 8.00 14.41C10RX001 6.36 0.62 1.09 0.12 0.00 0.00 11.07 19.26C10RX002 8.78 0.85 1.91 0.22 0.00 0.00 15.30 27.06C10RX003 14.70 1.43 4.50 0.51 0.00 0.00 25.61 46.75C10WC003 0.89 0.07 0.55 0.06 0.00 0.00 1.39 2.96C10WC006 1.09 0.09 1.34 0.15 0.00 0.00 1.71 4.38C10WC007 1.67 0.14 2.19 0.25 0.00 0.00 2.61 6.86C10WC008 3.02 0.25 1.23 0.14 0.00 0.00 4.71 9.35C10WC010 2.04 0.20 2.68 0.31 0.00 0.00 3.55 8.78

2 206

EP 1110-1-8, Vol. 130 Nov 09

2-268


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

C10 cont.C10WC015 6.04 0.50 1.91 0.22 0.00 0.00 9.41 18.08C10WC016 6.69 0.65 2.73 0.31 0.00 0.00 11.65 22.03C10WC017 2.70 0.26 1.23 0.14 0.00 0.00 4.70 9.03C10WC019 6.34 0.62 2.73 0.31 0.00 0.00 11.05 21.05

C15C15BL001 1.98 0.21 0.20 0.62 0.00 0.00 2.75 5.76C15BL003 9.49 1.00 0.99 2.09 0.00 0.00 13.18 26.75C15BL004 11.11 1.17 1.49 2.63 0.00 0.00 15.43 31.83C15BL005 16.28 1.72 2.98 3.77 0.00 0.00 22.61 47.36C15BL006 0.41 0.08 49.93 6.64 0.00 0.00 0.57 57.63C15ED001 1.44 0.15 2.09 0.32 0.00 0.00 2.00 6.00C15ED002 0.89 0.09 1.71 0.26 0.00 0.00 1.24 4.19C15XX001 13.05 2.53 28.05 3.73 0.38 0.06 18.17 65.97

C20C20WC002 2.09 0.24 2.47 0.38 0.18 0.03 2.30 7.69C20XX001 1.48 0.17 1.52 0.23 0.13 0.02 1.62 5.17

C25C25AJ001 0.73 0.09 1.14 0.17 0.00 0.00 0.91 3.04C25AJ003 1.04 0.13 1.14 0.17 0.00 0.00 1.28 3.76C25AJ004 1.48 0.19 1.52 0.23 0.00 0.00 1.83 5.25C25AJ005 1.74 0.22 2.09 0.32 0.00 0.00 2.15 6.52C25AJ006 2.07 0.26 2.09 0.32 0.00 0.00 2.55 7.29C25AJ007 2.20 0.28 2.09 0.32 0.00 0.00 2.71 7.60C25AJ008 1.37 0.32 0.98 0.20 0.00 0.00 1.45 4.32C25AJ009 1.45 0.34 0.98 0.20 0.00 0.00 1.54 4.51

2 207

EP 1110-1-8, Vol. 130 Nov 09

2-269


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

C25 cont.C25AJ010 1.55 0.36 0.98 0.20 0.00 0.00 1.64 4.73C25AJ011 1.66 0.39 0.98 0.20 0.00 0.00 1.76 4.99C25AJ012 1.76 0.41 0.98 0.20 0.00 0.00 1.87 5.22C25AJ013 1.87 0.43 0.98 0.20 0.00 0.00 1.98 5.46C25AJ015 1.95 0.25 3.79 0.58 0.00 0.00 2.41 8.98C25AJ016 2.05 0.26 3.79 0.58 0.00 0.00 2.53 9.21C25AJ018 2.38 0.30 4.74 0.72 0.00 0.00 2.93 11.07C25AJ019 3.44 0.44 5.31 0.81 0.00 0.00 4.25 14.25C25ST001 0.41 0.05 1.52 0.23 0.00 0.00 0.50 2.71C25ST002 0.42 0.05 1.71 0.26 0.00 0.00 0.51 2.95C25SV001 26.23 6.15 6.39 1.15 0.41 0.07 27.83 68.23C25SV002 24.68 5.78 6.39 1.15 0.31 0.05 26.18 64.54C25SV003 12.33 2.91 2.95 0.53 0.28 0.05 13.10 32.15C25WC002 0.50 0.06 1.52 0.23 0.00 0.00 0.62 2.93

C35C35AF001 2.81 0.53 0.00 0.30 0.03 0.01 4.18 7.86C35AF002 1.52 0.29 0.00 2.00 0.03 0.01 2.26 6.11C35AF004 4.49 0.85 3.42 2.46 0.05 0.01 6.67 17.95C35AF005 6.67 1.26 6.16 2.82 0.12 0.02 9.92 26.97C35AL002 4.42 0.85 3.42 1.46 0.20 0.03 6.60 16.98C35AL003 1.47 0.30 0.53 0.47 0.20 0.03 2.24 5.24C35AL008 2.66 0.50 0.00 0.30 0.00 0.00 3.94 7.40C35AL013 1.30 0.26 0.00 0.40 0.10 0.02 1.96 4.04C35AL014 6.94 1.30 6.96 1.43 0.05 0.01 10.30 26.99C35AV006 9.91 1.87 2.13 3.14 0.11 0.02 14.71 31.89C35AV008 2.98 0.56 0.75 2.40 0.00 0.00 4.41 11.10C35AV009 3.62 0.68 1.70 2.91 0.00 0.00 5.37 14.28

2 208

EP 1110-1-8, Vol. 130 Nov 09

2-270


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

C35 cont.C35AV010 6.53 1.22 2.77 3.48 0.00 0.00 9.68 23.68C35AV011 5.03 0.94 1.28 2.68 0.00 0.00 7.45 17.38C35AV012 14.98 2.80 2.13 3.64 0.00 0.00 22.19 45.74

C40C40CC001 4.14 0.53 0.99 0.59 0.00 0.00 5.11 11.36C40MU001 0.48 0.06 1.52 0.23 0.03 0.01 0.59 2.92C40MU002 1.00 0.13 2.47 0.38 0.03 0.01 1.24 5.26C40MU003 0.48 0.07 1.52 0.23 0.03 0.01 0.60 2.94C40MU004 0.55 0.07 1.52 0.23 0.03 0.01 0.69 3.10C40ST001 0.31 0.04 0.05 0.23 0.03 0.01 0.39 1.06C40ST002 0.34 0.05 1.04 0.16 0.03 0.01 0.43 2.06C40ST003 0.41 0.06 0.20 0.37 0.03 0.01 0.51 1.59C40ST005 0.54 0.07 0.15 0.39 0.03 0.01 0.68 1.87C40XX001 0.55 0.07 0.20 0.32 0.00 0.00 0.68 1.82C40XX002 0.59 0.07 1.33 0.20 0.00 0.00 0.73 2.92C40XX003 0.84 0.11 0.30 0.38 0.00 0.00 1.04 2.67C40XX004 0.85 0.11 1.52 0.23 0.00 0.00 1.04 3.75C40XX005 1.11 0.14 0.50 0.55 0.00 0.00 1.36 3.66C40XX006 1.54 0.20 0.50 0.55 0.00 0.00 1.90 4.69C40XX007 1.43 0.18 1.71 0.26 0.00 0.00 1.77 5.35

C45C45GO010 20.23 3.01 10.50 1.40 0.00 0.00 31.36 66.50C45GO011 31.16 4.63 21.11 2.81 0.00 0.00 48.29 108.00C45GO012 41.72 6.20 19.29 2.57 0.00 0.00 64.66 134.44C45GO013 16.78 2.49 10.50 1.40 0.00 0.00 26.01 57.18C45GO014 23.14 3.44 11.18 1.49 0.00 0.00 35.87 75.12

2 209

EP 1110-1-8, Vol. 130 Nov 09

2-271


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

C45 cont.C45GO016 45.57 6.77 26.25 3.49 0.00 0.00 70.64 152.72C45GO018 56.80 8.44 38.23 5.09 0.00 0.00 88.04 196.60C45GO020 67.94 10.10 51.35 6.83 0.00 0.00 105.30 241.52C45GO026 7.25 1.08 7.37 1.12 0.00 0.00 11.23 28.05C45GO027 9.21 1.37 5.71 0.76 0.00 0.00 14.28 31.33C45GO028 14.65 2.18 5.71 0.76 0.00 0.00 22.71 46.01C45GO029 9.74 1.45 7.37 1.12 0.00 0.00 15.10 34.78C45GO031 55.19 8.20 43.94 5.85 0.00 0.00 85.54 198.72C45MJ001 0.98 0.15 3.07 0.47 0.00 0.00 1.52 6.19C45MW002 6.01 0.90 2.97 0.40 0.09 0.02 9.33 19.72C45MW003 7.62 1.14 2.97 0.40 0.12 0.02 11.84 24.11

C55C55M3001 2.57 0.42 8.72 1.32 0.05 0.01 3.53 16.62C55M3002 5.84 0.93 6.47 0.86 0.00 0.00 8.01 22.11C55M3003 6.87 1.10 11.42 1.52 0.00 0.00 9.42 30.33C55OE001 29.27 4.68 0.00 0.00 0.00 0.00 40.13 74.08C55OE002 37.58 6.01 0.00 0.00 0.00 0.00 51.52 95.11C55OE003 57.21 9.14 0.00 0.00 0.00 0.00 78.45 144.80C55OE006 5.46 0.88 7.98 1.06 0.10 0.02 7.49 22.99C55OE009 10.30 1.67 13.69 1.82 0.19 0.03 14.13 41.83C55OE011 9.52 1.54 19.51 2.60 0.19 0.03 13.07 46.46C55OE012 12.12 1.96 19.51 2.60 0.19 0.03 16.64 53.05C55SC001 7.88 1.27 8.62 1.15 0.05 0.01 10.81 29.79C55SC002 19.27 3.10 19.08 2.54 0.20 0.03 26.44 70.66C55SC005 40.35 6.52 26.49 3.52 0.76 0.13 55.38 133.15C55SC006 48.25 7.78 26.49 3.52 0.76 0.13 66.21 153.14

2 210

EP 1110-1-8, Vol. 130 Nov 09

2-272


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

C60C60CQ001 1.89 0.24 8.53 1.30 0.00 0.00 2.59 14.55C60CQ002 0.43 0.05 2.19 0.33 0.00 0.00 0.59 3.59C60CQ003 0.46 0.06 3.17 0.48 0.00 0.00 0.63 4.80C60CQ010 1.95 0.24 8.53 1.30 0.00 0.00 2.68 14.70C60CQ011 3.26 0.41 9.00 1.62 0.00 0.00 4.47 18.76C60CQ012 3.27 0.41 9.00 1.62 0.00 0.00 4.48 18.78C60CQ013 3.30 0.41 9.00 1.62 0.00 0.00 4.52 18.85C60CQ014 2.03 0.25 3.83 2.05 0.00 0.00 2.78 10.94C60CQ016 4.16 0.52 11.45 2.07 0.00 0.00 5.71 23.91C60FE002 0.22 0.03 0.49 0.07 0.00 0.00 0.30 1.11C60FE006 0.46 0.06 2.19 0.33 0.00 0.00 0.63 3.67C60FE007 0.48 0.06 3.17 0.48 0.00 0.00 0.66 4.85C60FE009 1.54 0.19 4.88 0.74 0.00 0.00 2.11 9.46C60LY001 3.93 0.49 2.44 0.37 0.00 0.00 5.39 12.62C60LY002 5.81 0.72 8.53 1.30 0.00 0.00 7.97 24.33C60LY005 0.45 0.06 3.17 0.48 0.00 0.00 0.62 4.78C60LY011 11.24 1.40 4.36 0.79 0.00 0.00 15.41 33.20

C65C65ST007 0.20 0.02 0.09 0.05 0.00 0.00 0.73 1.09C65ST008 0.21 0.02 0.18 0.10 0.00 0.00 0.76 1.27C65ST009 0.25 0.02 0.28 0.15 0.00 0.00 0.90 1.60C65ST013 0.46 0.04 0.98 0.15 0.00 0.00 1.65 3.28C65WC003 0.34 0.03 0.18 0.24 0.00 0.00 1.24 2.03C65WC004 0.22 0.02 0.28 0.29 0.00 0.00 0.79 1.60C65WC005 0.42 0.04 0.89 0.14 0.00 0.00 1.51 3.00

2 211

EP 1110-1-8, Vol. 130 Nov 09

2-273


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

C75C75BD004 5.02 1.48 8.60 1.31 0.34 0.06 5.59 22.40C75BD005 6.30 1.86 14.12 2.14 0.44 0.07 7.02 31.95C75BD006 9.17 2.72 22.51 3.42 0.74 0.12 10.23 48.91C75BD007 3.64 1.07 7.78 1.18 0.17 0.03 4.05 17.92C75BD008 4.85 1.42 8.60 1.31 0.17 0.03 5.40 21.78C75BD009 6.51 1.92 14.12 2.14 0.44 0.07 7.25 32.45C75BD010 10.87 3.21 9.70 1.38 0.74 0.12 12.11 38.13C75BD011 14.43 4.26 14.84 2.11 1.59 0.27 16.08 53.58C75GV014 29.69 9.15 27.39 3.90 14.25 2.39 33.30 120.07C75GV016 69.98 20.81 34.24 4.88 12.65 2.13 78.06 222.75C75GV019 29.67 9.14 27.39 3.90 14.25 2.39 33.28 120.02C75GV020 48.67 14.61 28.53 4.06 12.65 2.13 54.36 165.01C75GV021 7.28 2.15 12.69 1.93 0.47 0.08 8.11 32.71C75GV022 8.97 2.66 12.55 1.79 0.77 0.13 10.01 36.88C75GV023 16.71 5.19 17.35 2.47 9.17 1.54 18.76 71.19C75GV024 26.12 7.93 19.74 2.81 9.17 1.54 29.23 96.54C75GV025 48.17 14.52 28.53 4.06 13.50 2.27 53.85 164.90C75GV028 16.83 5.00 17.35 2.47 2.55 0.43 18.77 63.40C75PB002 28.23 8.37 21.11 3.01 2.47 0.41 31.47 95.07C75TD003 22.70 6.73 20.54 2.93 3.54 0.59 25.31 82.34C75TD007 42.41 12.78 28.19 4.02 6.96 1.17 47.40 142.93C75TD008 39.22 11.85 28.19 4.02 12.42 2.09 43.86 141.65C75TE001 21.50 6.33 14.84 2.11 1.90 0.32 23.95 70.95C75TE002 29.50 8.71 17.35 2.47 3.11 0.52 32.87 94.53

C80C80GV006 36.65 12.17 39.31 4.86 1.28 0.22 35.70 130.19 41.89 12.27 51.99 6.43 4.98 0.84 43.71 162.11

2 212

EP 1110-1-8, Vol. 130 Nov 09

2-274


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

C80 cont.C80GV013 87.07 35.80 28.23 3.49 8.87 1.49 109.03 273.98 96.74 35.97 35.97 4.45 35.98 6.04 127.98 343.13C80GV014 87.32 35.90 28.23 3.49 8.87 1.49 109.35 274.65 97.02 36.08 35.97 4.45 35.98 6.04 128.35 343.89C80GV015 87.82 36.10 28.23 3.49 8.87 1.49 109.97 275.97 97.58 36.28 35.97 4.45 35.98 6.04 129.08 345.38C80GV016 123.59 50.74 25.95 3.20 10.46 1.76 154.73 370.43 137.32 50.99 33.14 4.10 41.83 7.03 181.62 456.03C80GV020 41.19 15.30 39.31 4.86 1.76 0.30 45.85 148.57 46.34 15.40 51.99 6.43 6.88 1.16 54.80 183.00C80GV025 23.88 7.94 29.48 3.65 1.03 0.17 23.27 89.42 27.30 8.01 38.99 4.82 4.03 0.68 28.49 112.32C80GV026 36.02 12.00 34.20 4.23 1.88 0.32 35.10 123.75 41.17 12.10 45.23 5.59 7.36 1.24 42.98 155.67C80GV029 36.68 12.24 39.31 4.86 2.25 0.38 35.75 131.47 41.92 12.34 51.99 6.43 8.90 1.50 43.77 166.85C80GV030 36.74 12.26 39.31 4.86 2.25 0.38 35.81 131.61 41.99 12.36 51.99 6.43 8.90 1.50 43.85 167.02C80GV031 37.00 13.78 39.31 4.86 2.25 0.38 41.20 138.78 41.62 13.87 51.99 6.43 8.90 1.50 49.24 173.55C80GV032 49.16 18.37 41.47 5.13 6.83 1.15 54.77 176.88 55.30 18.49 54.85 6.78 26.77 4.50 65.46 232.15C80LI009 29.35 9.78 34.39 4.25 1.64 0.28 28.60 108.29 33.54 9.86 45.49 5.62 6.59 1.11 35.02 137.23C80LI010 26.06 8.72 30.96 3.83 1.95 0.33 25.41 97.26 29.78 8.79 40.94 5.06 7.70 1.29 31.11 124.67C80LI011 30.04 10.06 35.87 4.44 2.25 0.38 29.30 112.34 34.33 10.14 47.44 5.87 8.91 1.50 35.87 144.06C80TD001 34.09 12.82 18.36 2.27 3.94 0.66 38.02 110.16 38.35 12.90 23.50 2.91 15.93 2.68 45.44 141.71C80TD002 42.66 15.98 22.49 2.78 3.83 0.64 47.54 135.92 47.99 16.08 28.89 3.57 14.99 2.52 56.82 170.86C80TD005 46.06 19.08 61.71 7.63 4.84 0.81 57.74 197.87 51.18 19.18 80.47 9.95 19.21 3.23 67.78 251.00C80TE002 19.09 6.39 24.57 3.04 1.42 0.24 18.61 73.36 21.82 6.44 32.49 4.02 5.68 0.95 22.79 94.19C80TE003 25.31 8.49 36.36 4.50 2.15 0.36 24.69 101.86 28.93 8.56 48.09 5.95 8.53 1.43 30.23 131.72C80TE008 16.66 4.98 12.78 2.19 3.42 0.57 13.95 54.55 19.44 5.03 16.90 2.89 13.39 2.25 17.63 77.53C80XX001 8.48 2.53 24.08 4.12 0.99 0.17 7.10 47.47 9.90 2.56 31.84 5.45 3.95 0.66 8.98 63.34C80XX002 11.11 3.33 29.48 5.05 1.56 0.26 9.31 60.10 12.97 3.37 38.99 6.67 6.27 1.05 11.77 81.09

C85C85KC003 43.82 17.86 15.96 1.67 0.00 0.00 51.76 131.07 54.78 18.07 21.00 2.19 0.00 0.00 68.51 164.55C85KC004 27.65 11.27 10.72 1.12 0.00 0.00 32.66 83.42 34.56 11.40 14.11 1.47 0.00 0.00 43.22 104.76C85KC005 31.95 13.02 12.83 1.34 0.00 0.00 37.74 96.88 39.94 13.17 16.88 1.76 0.00 0.00 49.95 121.70C85KC006 74.61 33.28 16.80 1.91 0.00 0.00 98.57 225.17 91.19 33.61 22.11 2.52 0.00 0.00 126.81 276.24

2 213

EP 1110-1-8, Vol. 130 Nov 09

2-275


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

C85 cont.C85KC007 26.76 10.88 10.72 1.02 0.00 0.00 29.63 79.01 32.11 10.98 14.11 1.34 0.00 0.00 37.93 96.47C85KC008 52.96 23.63 19.03 2.17 0.00 0.00 69.97 167.76 64.73 23.86 25.04 2.85 0.00 0.00 90.02 206.50C85LB013 35.30 14.38 15.84 1.65 0.00 0.00 41.69 108.86 44.12 14.55 20.84 2.18 0.00 0.00 55.17 136.86C85LB014 40.23 16.40 17.11 1.79 0.00 0.00 47.52 123.05 50.29 16.59 22.51 2.35 0.00 0.00 62.89 154.63C85LB015 55.80 22.74 17.11 1.79 0.00 0.00 65.91 163.35 69.75 23.00 22.51 2.35 0.00 0.00 87.22 204.83C85LB016 63.96 28.53 17.11 1.95 0.00 0.00 84.51 196.06 78.18 28.82 22.51 2.56 0.00 0.00 108.72 240.79C85LB017 72.25 32.23 26.50 3.02 0.00 0.00 95.45 229.45 88.30 32.55 34.87 3.97 0.00 0.00 122.79 282.48C85LB019 40.37 14.68 21.68 3.50 0.00 0.00 50.67 130.90 49.69 14.87 28.35 4.57 0.00 0.00 69.75 167.23C85LB021 58.35 23.72 23.41 2.44 0.00 0.00 81.91 189.83 70.02 23.94 30.61 3.20 0.00 0.00 108.62 236.39C85LB022 67.38 27.39 19.53 2.04 0.00 0.00 94.59 210.93 80.86 27.65 25.54 2.67 0.00 0.00 125.44 262.16C85LB023 71.48 32.13 36.26 4.13 0.00 0.00 110.88 254.88 89.35 32.49 47.42 5.40 0.00 0.00 151.78 326.44C85LI001 28.91 11.78 12.47 1.30 0.00 0.00 34.15 88.61 36.14 11.92 16.40 1.71 0.00 0.00 45.19 111.36C85MA001 46.17 18.77 28.85 3.01 0.00 0.00 64.81 161.61 55.40 18.95 37.72 3.94 0.00 0.00 85.94 201.95C85MA002 56.73 23.06 28.02 2.92 0.00 0.00 79.63 190.36 68.07 23.28 36.65 3.83 0.00 0.00 105.59 237.42C85MA003 75.98 34.15 30.91 3.52 0.00 0.00 117.87 262.43 94.98 34.54 40.42 4.60 0.00 0.00 161.34 335.88C85MA004 43.69 17.81 21.08 2.20 0.00 0.00 51.61 136.39 54.61 18.01 27.74 2.90 0.00 0.00 68.30 171.56C85MA005 41.00 16.71 20.18 2.11 0.00 0.00 48.42 128.42 51.25 16.90 26.55 2.77 0.00 0.00 64.09 161.56C85MA006 51.81 23.11 20.48 2.33 0.00 0.00 68.45 166.18 63.33 23.34 26.95 3.07 0.00 0.00 88.06 204.75C85MA007 73.04 32.58 22.59 2.57 0.00 0.00 96.50 227.28 89.27 32.91 29.72 3.38 0.00 0.00 124.14 279.42C85MA008 43.43 17.70 20.18 2.11 0.00 0.00 51.29 134.71 54.28 17.90 26.55 2.77 0.00 0.00 67.89 169.39C85MA009 66.66 29.97 28.02 3.19 0.00 0.00 103.41 231.25 83.33 30.30 36.65 4.17 0.00 0.00 141.55 296.00C85MA010 66.01 29.45 20.48 2.33 0.00 0.00 87.21 205.48 80.68 29.74 26.95 3.07 0.00 0.00 112.20 252.64C85TE001 32.73 11.90 12.36 1.99 0.00 0.00 41.08 100.06 40.29 12.05 16.17 2.61 0.00 0.00 56.55 127.67C85TE002 45.55 16.56 20.61 3.32 0.00 0.00 57.16 143.20 56.06 16.77 26.95 4.35 0.00 0.00 78.69 182.82C85TE003 51.12 20.78 27.61 2.88 0.00 0.00 71.75 174.14 61.34 20.98 36.11 3.77 0.00 0.00 95.15 217.35C85TE008 29.29 11.94 11.08 1.16 0.00 0.00 34.59 88.06 36.61 12.07 14.58 1.52 0.00 0.00 45.78 110.56C85TE009 36.11 14.72 13.85 1.45 0.00 0.00 42.66 108.79 45.14 14.89 18.23 1.90 0.00 0.00 56.46 136.62

2 214

EP 1110-1-8, Vol. 130 Nov 09

2-276


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

C85 cont.C85TE010 47.88 19.51 14.46 1.51 0.00 0.00 56.56 139.92 59.86 19.74 19.02 1.99 0.00 0.00 74.85 175.46C85TE011 64.32 28.69 18.97 2.16 0.00 0.00 84.97 199.11 78.61 28.98 24.96 2.84 0.00 0.00 109.31 244.70

C90C90LB001 59.26 26.92 22.97 2.84 7.98 1.34 78.90 200.21 65.84 27.05 28.93 3.57 31.90 5.36 92.62 255.27C90LB002 67.00 30.40 26.85 3.32 7.98 1.34 89.20 226.09 74.45 30.54 33.94 4.19 31.90 5.36 104.70 285.08C90LB003 107.65 48.81 40.69 5.03 11.97 2.01 143.30 359.46 119.62 49.05 51.83 6.41 47.86 8.04 168.20 451.01

C95C95AP004 23.43 9.52 11.81 11.01 0.00 0.00 29.40 85.17C95AP005 0.74 0.30 0.00 0.00 0.00 0.00 0.93 1.97C95AP006 1.41 0.57 0.00 0.00 0.00 0.00 1.77 3.75C95AP007 37.04 15.05 19.66 16.67 0.00 0.00 46.48 134.90C95AP008 5.69 2.31 0.00 0.50 0.00 0.00 7.14 15.64C95AP009 1.89 0.77 0.00 0.00 0.00 0.00 2.38 5.04C95AP010 49.36 20.07 20.03 16.89 0.00 0.00 61.95 168.30C95AP011 1.77 0.72 0.00 0.00 0.00 0.00 2.22 4.71C95AP012 7.09 2.88 0.00 0.50 0.00 0.00 8.90 19.37C95AP013 47.31 19.23 32.67 24.39 0.00 0.00 59.38 182.98C95AP014 1.61 0.65 0.00 0.00 0.00 0.00 2.02 4.28C95AP015 6.18 2.51 0.00 0.50 0.00 0.00 7.76 16.95C95AP016 2.16 0.88 0.00 0.00 0.00 0.00 2.71 5.75C95AP017 20.02 8.14 11.54 9.85 0.00 0.00 25.13 74.68C95AP018 0.67 0.27 0.00 0.00 0.00 0.00 0.85 1.79C95AP019 3.85 1.56 0.00 0.50 0.00 0.00 4.83 10.74C95AP020 22.04 8.96 20.58 15.22 0.00 0.00 27.66 94.46C95AP021 34.44 14.00 23.81 18.13 0.00 0.00 43.23 133.61C95AP022 5.21 2.12 2.22 2.32 0.00 0.00 6.54 18.41

2 215

EP 1110-1-8, Vol. 130 Nov 09

2-277


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

C95 cont.C95AP023 0.12 0.05 0.00 0.00 0.00 0.00 0.15 0.32C95LH003 20.47 8.32 10.06 8.97 0.00 0.00 25.69 73.51C95LH005 26.62 10.82 13.66 12.11 0.00 0.00 33.41 96.62C95LH011 49.74 20.22 20.58 17.22 0.00 0.00 62.43 170.19C95LH013 63.55 25.83 20.58 17.22 0.00 0.00 79.76 206.94C95LH015 84.71 34.43 29.26 24.37 0.00 0.00 106.31 279.08C95LH022 18.09 7.41 3.23 3.92 0.57 0.10 22.74 56.06C95LH023 25.25 10.33 6.00 6.56 0.67 0.11 31.73 80.65

D10D10IR003 8.64 3.06 0.00 0.79 0.00 0.00 15.21 27.70D10IR005 32.54 8.41 25.90 3.45 0.00 0.00 57.27 127.57D10SU002 10.64 3.77 0.00 0.80 0.00 0.00 18.73 33.94D10SU003 10.91 3.86 0.00 0.80 0.00 0.00 19.20 34.77D10SU005 16.59 4.29 31.32 4.17 0.00 0.00 29.21 85.58D10SU006 16.79 4.34 31.32 4.17 0.00 0.00 29.56 86.18

D15D15BI001 1.12 0.29 2.60 0.39 0.00 0.00 1.78 6.18D15BI002 2.01 0.52 2.41 0.32 0.00 0.00 3.19 8.45D15BI003 3.04 0.79 3.61 0.48 0.00 0.00 4.82 12.74D15BI004 4.74 1.23 5.42 0.72 0.00 0.00 7.51 19.62D15BI005 6.10 1.58 7.47 0.99 0.00 0.00 9.66 25.80D15BI006 10.24 2.65 14.33 1.91 0.00 0.00 16.22 45.35D15BI007 13.57 3.51 22.77 3.03 0.00 0.00 21.49 64.37D15BI008 12.65 3.27 22.77 3.03 0.00 0.00 20.04 61.76D15XX001 0.62 0.16 0.00 0.00 0.00 0.00 0.98 1.76D15XX002 0.93 0.24 0.00 0.00 0.00 0.00 1.47 2.64

2 216

EP 1110-1-8, Vol. 130 Nov 09

2-278


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

D20D20AD002 0.54 0.11 0.23 0.37 0.00 0.00 0.81 2.06D20AD005 0.53 0.11 0.23 0.37 0.00 0.00 0.79 2.03D20AD006 0.88 0.19 0.45 0.64 0.00 0.00 1.31 3.47D20AD007 1.45 0.31 0.91 1.29 0.00 0.00 2.17 6.13D20CQ001 1.30 0.27 3.47 1.76 0.00 0.00 1.95 8.75D20LY001 0.78 0.16 0.34 0.68 0.00 0.00 1.17 3.13D20LY002 0.81 0.17 0.00 0.60 0.00 0.00 1.21 2.79

D25D25AD003 7.58 1.96 8.31 0.95 0.00 0.00 13.34 32.14D25AD004 6.05 1.56 3.37 0.38 0.00 0.00 10.64 22.00D25EZ001 0.57 0.15 0.00 0.50 0.00 0.00 1.01 2.23D25EZ002 0.46 0.13 0.00 0.50 0.09 0.02 0.83 2.03D25EZ003 0.51 0.14 0.00 0.50 0.06 0.01 0.90 2.12D25EZ005 1.91 0.51 0.00 1.25 0.12 0.02 3.39 7.20

D30D30HD001 5.75 1.49 25.30 5.37 0.00 0.00 10.12 48.03D30HD002 8.62 2.23 32.52 7.33 0.00 0.00 15.18 65.88D30HD003 11.22 2.90 40.35 9.37 0.00 0.00 19.75 83.59D30MR001 0.93 0.24 1.73 0.26 0.00 0.00 1.64 4.80D30MR003 6.26 1.64 6.99 0.93 0.12 0.02 11.05 27.01D30MR005 15.04 3.94 16.32 2.17 0.45 0.08 26.57 64.57D30MR006 15.50 4.06 18.67 2.48 0.45 0.08 27.38 68.62D30MR007 19.64 5.13 18.67 2.48 0.45 0.08 34.67 81.12

D35D35DT001 33.76 10.83 54.21 9.79 0.00 0.00 55.71 164.30

2 217

EP 1110-1-8, Vol. 130 Nov 09

2-279


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

D35 cont.D35DT002 34.71 11.13 54.21 9.79 0.00 0.00 57.26 167.10D35DT003 39.30 12.60 54.21 9.79 0.00 0.00 64.84 180.74D35DT004 41.73 13.38 63.24 11.42 0.00 0.00 68.85 198.62D35DT005 65.06 20.86 91.55 16.53 0.00 0.00 107.35 301.35D35DT006 44.81 18.21 91.55 13.90 0.00 0.00 73.93 242.40D35IB003 29.06 11.89 64.27 9.76 0.76 0.13 48.02 163.89D35IB004 27.65 11.34 63.06 9.58 0.93 0.16 45.70 158.42D35IB005 32.09 13.14 76.31 11.59 0.93 0.16 53.03 187.25D35IB006 33.76 13.82 77.94 11.84 0.93 0.16 55.77 194.22D35RD001 25.48 8.17 54.67 9.87 0.00 0.00 42.04 140.23

F10F10JC001 5.51 1.33 7.37 0.84 0.59 0.10 6.41 22.15F10JC002 6.00 1.44 7.37 0.84 0.59 0.10 6.98 23.32

G10G10CA012 3.06 0.59 30.86 3.51 0.00 0.00 3.04 41.06 3.82 0.61 40.81 4.64 0.00 0.00 4.34 54.22G10CA013 3.94 0.77 39.80 4.53 0.00 0.00 3.92 52.96 4.93 0.79 52.64 5.99 0.00 0.00 5.60 69.95G10CA014 5.17 1.01 52.67 5.99 0.00 0.00 5.14 69.98 6.46 1.03 69.66 7.93 0.00 0.00 7.35 92.43G10CA015 7.16 1.39 67.51 7.68 0.00 0.00 7.12 90.86 8.95 1.43 89.29 10.16 0.00 0.00 10.18 120.01G10CA016 8.76 1.70 80.29 9.14 0.00 0.00 8.71 108.60 10.94 1.75 106.19 12.08 0.00 0.00 12.44 143.40G10CA017 13.76 2.68 107.02 12.18 0.00 0.00 13.68 149.32 17.19 2.75 141.54 16.11 0.00 0.00 19.54 197.13G10CA018 17.47 3.40 141.80 16.14 0.00 0.00 17.37 196.18 21.84 3.49 187.55 21.34 0.00 0.00 24.82 259.04G10CA019 29.27 5.70 226.41 25.76 0.00 0.00 29.11 316.25 36.59 5.85 299.45 34.08 0.00 0.00 41.59 417.56G10CA020 2.44 0.47 17.10 1.95 0.00 0.00 2.43 24.39 3.05 0.49 22.61 2.57 0.00 0.00 3.47 32.19G10WC001 0.24 0.04 1.42 0.16 0.00 0.00 0.21 2.07 0.28 0.04 1.85 0.21 0.00 0.00 0.28 2.66G10WC002 0.28 0.05 1.95 0.22 0.00 0.00 0.24 2.74 0.32 0.05 2.55 0.29 0.00 0.00 0.32 3.53G10WC003 0.52 0.08 2.84 0.32 0.00 0.00 0.45 4.21 0.60 0.09 3.71 0.42 0.00 0.00 0.60 5.42

2 218

EP 1110-1-8, Vol. 130 Nov 09

2-280


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

G10 cont.G10WC004 0.42 0.07 3.20 0.36 0.00 0.00 0.36 4.41 0.48 0.07 4.17 0.47 0.00 0.00 0.48 5.67G10XX001 0.11 0.02 0.18 0.02 0.00 0.00 0.09 0.42 0.13 0.02 0.23 0.03 0.00 0.00 0.13 0.54G10XX002 0.54 0.09 3.37 0.38 0.00 0.00 0.46 4.84 0.62 0.09 4.40 0.50 0.00 0.00 0.62 6.23G10XX003 1.24 0.20 2.26 0.26 0.00 0.00 1.05 5.01 1.41 0.20 2.99 0.34 0.00 0.00 1.41 6.35G10XX004 0.64 0.10 0.88 0.10 0.00 0.00 0.54 2.26 0.73 0.10 1.17 0.13 0.00 0.00 0.73 2.86G10XX005 1.56 0.30 6.39 0.73 0.00 0.00 1.55 10.53 1.95 0.31 8.34 0.95 0.00 0.00 2.22 13.77G10XX006 1.38 0.27 8.88 1.01 0.00 0.00 1.37 12.91 1.72 0.27 11.59 1.32 0.00 0.00 1.95 16.85G10XX007 2.07 0.40 12.43 1.41 0.00 0.00 2.06 18.37 2.59 0.41 16.22 1.85 0.00 0.00 2.95 24.02G10XX008 2.54 0.49 10.51 1.20 0.00 0.00 2.52 17.26 3.17 0.51 13.91 1.58 0.00 0.00 3.61 22.78G10XX009 2.18 0.42 14.05 1.60 0.00 0.00 2.17 20.42 2.72 0.44 18.59 2.12 0.00 0.00 3.10 26.97G10XX010 3.24 0.63 19.65 2.24 0.00 0.00 3.22 28.98 4.05 0.65 25.99 2.96 0.00 0.00 4.61 38.26G10XX011 3.57 0.69 36.85 4.19 0.00 0.00 3.55 48.85 4.46 0.71 48.74 5.55 0.00 0.00 5.07 64.53G10XX012 4.23 0.82 42.06 4.79 0.00 0.00 4.21 56.11 5.29 0.85 55.63 6.33 0.00 0.00 6.01 74.11G10XX013 5.29 1.03 56.01 6.37 0.00 0.00 5.26 73.96 6.62 1.06 74.08 8.43 0.00 0.00 7.52 97.71G10XX014 7.61 1.48 70.07 7.97 0.00 0.00 7.56 94.69 9.51 1.52 92.67 10.55 0.00 0.00 10.81 125.06G10XX015 12.54 2.44 103.18 11.74 0.00 0.00 12.47 142.37 15.67 2.50 136.47 15.53 0.00 0.00 17.81 187.98G10XX016 17.72 3.45 140.03 15.93 0.00 0.00 17.62 194.75 22.14 3.54 185.21 21.08 0.00 0.00 25.17 257.14

G15G15CA001 11.28 4.17 11.49 1.85 0.87 0.15 13.83 43.64 12.12 4.19 14.66 2.36 2.88 0.48 16.85 53.54G15CA003 13.26 4.90 12.87 2.08 0.87 0.15 16.25 50.38 14.24 4.92 16.42 2.65 2.88 0.48 19.80 61.39G15CA004 14.17 5.24 15.17 2.45 0.97 0.16 17.37 55.53 15.22 5.26 19.35 3.12 3.21 0.54 21.16 67.86G15CA005 19.18 7.19 19.76 3.19 3.35 0.56 23.59 76.82 20.60 7.22 25.22 4.07 11.07 1.86 28.74 98.78G15CA006 27.71 10.35 25.28 4.08 4.69 0.79 34.06 106.96 29.77 10.40 32.25 5.20 15.47 2.60 41.49 137.18G15CA007 11.97 4.42 12.41 2.00 0.87 0.15 14.67 46.49 12.85 4.44 15.83 2.55 2.88 0.48 17.87 56.90G15CA008 16.44 6.07 17.01 2.74 1.10 0.18 20.14 63.68 17.66 6.09 21.70 3.50 3.72 0.62 24.54 77.83G15CA009 15.36 5.67 17.01 2.74 0.97 0.16 18.82 60.73 16.50 5.70 21.70 3.50 3.21 0.54 22.93 74.08G15CA010 17.79 6.56 18.39 2.97 1.10 0.18 21.80 68.79 19.11 6.59 23.46 3.78 3.72 0.62 26.55 83.83

2 219

EP 1110-1-8, Vol. 130 Nov 09

2-281


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

G15 cont.G15JD008 12.14 4.55 13.88 2.24 2.12 0.36 14.93 50.22 13.03 4.57 17.71 2.86 6.99 1.17 18.19 64.52G15JD009 14.02 5.24 14.34 2.31 2.40 0.40 17.24 55.95 15.06 5.26 18.30 2.95 8.09 1.36 21.00 72.02G15JD010 14.07 5.26 17.01 2.74 2.12 0.36 17.30 58.86 15.12 5.28 21.70 3.50 6.99 1.17 21.07 74.83G15JD011 15.94 5.94 18.85 3.04 2.40 0.40 19.57 66.14 17.12 5.97 24.04 3.88 8.09 1.36 23.84 84.30

H10H10NP001 0.97 0.14 0.00 0.50 0.00 0.00 1.50 3.11H10NP002 1.08 0.16 0.00 0.50 0.00 0.00 1.67 3.41H10NP003 1.62 0.24 0.00 0.75 0.00 0.00 2.49 5.10H10NP004 2.08 0.31 0.00 0.75 0.00 0.00 3.21 6.35H10NP005 2.76 0.41 0.00 1.00 0.00 0.00 4.25 8.42H10NP006 3.71 0.55 0.00 1.00 0.00 0.00 5.72 10.98H10NP008 5.63 0.84 0.00 1.25 0.00 0.00 8.68 16.40H10NP009 7.18 1.07 0.00 1.25 0.00 0.00 11.08 20.58H10NP015 8.75 1.30 0.00 1.25 0.00 0.00 13.49 24.79H10NP016 12.06 1.79 0.00 1.25 0.00 0.00 18.60 33.70H10NP017 15.74 2.34 0.00 1.25 0.00 0.00 24.28 43.61H10NP018 36.54 5.43 0.00 1.25 0.00 0.00 56.37 99.59

H13H13AY007 14.27 3.34 0.00 0.00 0.00 0.00 19.81 37.42H13AY008 7.01 1.64 0.00 0.00 0.00 0.00 9.74 18.39H13AY009 12.69 2.98 0.00 0.00 0.00 0.00 17.63 33.30H13AY010 6.47 1.52 0.00 0.00 0.00 0.00 8.99 16.98H13AY011 10.62 2.49 0.00 0.00 0.00 0.00 14.74 27.85H13AY012 5.43 1.27 0.00 0.00 0.00 0.00 7.55 14.25H13AY013 8.52 2.00 0.00 0.00 0.00 0.00 11.83 22.35H13AY014 4.58 1.07 0.00 0.00 0.00 0.00 6.36 12.01

2 220

EP 1110-1-8, Vol. 130 Nov 09

2-282


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

H13 cont.H13AY015 5.02 1.18 0.00 0.00 0.00 0.00 6.97 13.17H13AY016 3.25 0.76 0.00 0.00 0.00 0.00 4.52 8.53H13AY017 15.85 3.71 0.00 0.00 0.00 0.00 22.01 41.57H13AY018 8.07 1.89 0.00 0.00 0.00 0.00 11.21 21.17H13AY019 1.04 0.24 0.09 0.30 0.00 0.00 1.44 3.11H13AY020 1.34 0.31 0.09 0.30 0.00 0.00 1.86 3.90H13AY021 17.95 3.87 0.00 0.00 0.47 0.08 20.88 43.25H13AY022 9.69 2.11 0.00 0.00 0.47 0.08 11.29 23.64H13AY023 16.31 3.52 0.00 0.00 0.47 0.08 18.96 39.34H13AY024 8.60 1.87 0.00 0.00 0.47 0.08 10.01 21.03H13AY025 14.52 3.14 0.00 0.00 0.47 0.08 16.90 35.11H13AY026 7.92 1.73 0.00 0.00 0.47 0.08 9.22 19.42H13AY027 12.21 2.65 0.00 0.00 0.47 0.08 14.21 29.62H13AY028 6.71 1.47 0.00 0.00 0.47 0.08 7.82 16.55H13AY029 9.88 2.15 0.00 0.00 0.47 0.08 11.50 24.08H13AY030 5.69 1.25 0.00 0.00 0.47 0.08 6.64 14.13H13AY031 6.46 1.42 0.00 0.00 0.47 0.08 7.53 15.96H13AY032 4.25 0.95 0.00 0.00 0.47 0.08 4.97 10.72H13BB001 4.38 0.43 0.92 1.24 0.00 0.00 6.35 13.32H13BB002 3.90 0.38 1.38 1.74 0.00 0.00 5.66 13.06H13BC003 4.51 0.48 0.46 0.27 0.00 0.00 4.87 10.59H13BC006 4.21 0.44 0.28 0.17 0.00 0.00 4.55 9.65H13BC007 6.53 0.69 0.28 0.17 0.00 0.00 7.05 14.72H13BC008 7.99 0.84 0.46 0.27 0.00 0.00 8.63 18.19H13BC009 5.48 0.58 0.28 0.17 0.00 0.00 5.91 12.42H13BC010 3.22 0.34 0.28 0.17 0.00 0.00 3.48 7.49H13BC011 4.11 0.43 0.46 0.27 0.00 0.00 4.44 9.71

2 221

EP 1110-1-8, Vol. 130 Nov 09

2-283


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

H13 cont.H13BC012 3.36 0.35 0.28 0.17 0.00 0.00 3.63 7.79H13BC013 3.04 0.32 0.28 0.17 0.00 0.00 3.28 7.09H13CB001 2.03 0.43 0.46 0.52 0.00 0.00 2.36 5.80H13CB002 2.20 0.47 0.92 0.80 0.00 0.00 2.55 6.94H13CO002 0.96 0.21 0.46 0.52 0.00 0.00 1.12 3.27H13CO003 1.60 0.44 0.28 0.42 0.00 0.00 2.22 4.96H13CO004 2.35 0.65 0.28 0.67 0.00 0.00 3.27 7.22H13CO005 4.07 1.13 0.28 0.67 0.00 0.00 5.66 11.81H13CO006 3.43 0.95 0.28 0.52 0.00 0.00 4.76 9.94H13EP001 2.01 0.43 0.46 0.52 0.00 0.00 2.33 5.75H13EP002 2.58 0.72 0.69 0.71 0.00 0.00 3.58 8.28H13KP001 6.91 1.49 1.15 0.68 0.13 0.02 8.04 18.42H13KP002 7.85 1.69 1.43 0.85 0.13 0.02 9.12 21.09H13KP003 9.24 1.98 2.03 1.21 0.13 0.02 10.74 25.35H13KP004 10.63 2.28 2.58 1.53 0.13 0.02 12.36 29.53H13MN001 29.08 6.28 13.85 10.40 0.53 0.09 38.07 98.30H13MN002 34.00 7.35 18.46 13.86 0.69 0.12 44.52 119.00H13MN003 38.58 8.33 18.46 14.86 0.69 0.12 50.51 131.55H13MN004 44.08 9.50 27.69 20.79 0.69 0.12 57.69 160.56H13PR001 7.94 1.86 0.28 0.17 0.00 0.00 11.02 21.27H13PR002 23.53 5.06 0.28 1.67 0.47 0.08 27.35 58.44H13PR003 14.04 3.29 0.46 0.27 0.00 0.00 19.50 37.56H13PR005 18.51 4.34 0.46 0.27 0.00 0.00 25.70 49.28H13PR006 20.76 4.47 0.46 1.77 0.47 0.08 24.13 52.14H13PR007 22.81 5.35 0.92 0.55 0.00 0.00 31.68 61.31H13PR011 32.57 6.99 0.18 1.61 0.47 0.08 37.85 79.75H13PR012 35.01 7.52 0.28 1.67 0.47 0.08 40.69 85.72

2 222

EP 1110-1-8, Vol. 130 Nov 09

2-284


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

H13 cont.H13PR013 37.17 7.98 0.46 1.77 0.47 0.08 43.19 91.12H13PR014 41.71 8.95 0.74 1.94 0.47 0.08 48.46 102.35H13PR015 47.55 10.19 0.74 1.94 0.47 0.08 55.24 116.21H13PR022 16.41 3.85 0.18 0.11 0.00 0.00 22.79 43.34H13PR023 18.77 4.40 0.28 0.17 0.00 0.00 26.06 49.68H13PR024 20.80 4.88 0.28 0.17 0.00 0.00 28.89 55.02H13PR025 25.08 5.88 0.28 0.17 0.00 0.00 34.82 66.23H13PR026 30.57 7.17 0.37 0.22 0.00 0.00 42.45 80.78H13S5001 4.72 1.01 0.28 0.17 0.00 0.00 5.48 11.66H13S5002 7.40 1.58 0.46 0.27 0.00 0.00 8.59 18.30H13S5003 8.78 1.88 0.46 0.27 0.00 0.00 10.20 21.59H13SH001 4.59 0.98 1.85 0.99 0.00 0.00 6.00 14.41H13SH002 4.31 0.92 1.85 0.99 0.00 0.00 5.63 13.70H13SH003 7.41 1.58 3.69 1.97 0.00 0.00 9.69 24.34H13SH004 7.73 1.65 3.69 1.97 0.00 0.00 10.11 25.15H13SH005 12.39 2.65 9.23 4.93 0.00 0.00 16.20 45.40H13SH006 39.79 8.50 27.69 14.79 0.00 0.00 52.00 142.77H13SH007 51.81 11.06 55.38 29.59 0.00 0.00 67.72 215.56H13TH001 1.14 0.24 0.46 0.27 0.00 0.00 1.32 3.43H13TH002 2.11 0.46 0.88 0.10 0.06 0.01 2.45 6.07H13TH003 2.39 0.52 0.88 0.10 0.06 0.01 2.78 6.74H13YB001 31.17 6.66 4.62 2.74 0.00 0.00 36.19 81.38H13YB002 31.17 6.66 4.62 2.74 0.00 0.00 36.19 81.38H13YB003 31.17 6.66 4.62 2.74 0.00 0.00 36.19 81.38

H20H20BE002 3.41 0.73 0.00 0.20 0.00 0.00 4.21 8.55H20BE003 4.23 0.90 0.00 0.30 0.00 0.00 5.22 10.65

2 223

EP 1110-1-8, Vol. 130 Nov 09

2-285


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

H20 cont.H20BE004 4.66 0.99 0.00 0.40 0.00 0.00 5.74 11.79

H25H25AU001 1.05 0.14 0.00 0.00 0.00 0.00 1.53 2.72H25AU002 1.21 0.16 0.00 0.00 0.00 0.00 1.76 3.13H25AU003 1.69 0.23 0.00 0.00 0.00 0.00 2.45 4.37H25AU004 2.63 0.36 0.00 0.00 0.00 0.00 3.82 6.81H25AU005 2.64 0.36 0.00 0.00 0.00 0.00 3.83 6.83H25AX001 1.07 0.15 0.00 0.00 0.00 0.00 1.55 2.77H25AX002 1.26 0.17 0.00 0.00 0.00 0.00 1.82 3.25H25AX003 1.29 0.17 0.00 0.00 0.00 0.00 1.87 3.33H25AX004 1.56 0.21 0.00 0.00 0.00 0.00 2.26 4.03H25AX005 1.45 0.20 0.00 0.00 0.00 0.00 2.11 3.76H25AX006 1.79 0.24 0.00 0.00 0.00 0.00 2.60 4.63H25BS001 0.69 0.10 0.00 0.00 0.00 0.00 0.85 1.64H25BS002 0.80 0.12 0.00 0.00 0.00 0.00 0.98 1.90H25BS003 0.86 0.13 0.00 0.00 0.00 0.00 1.06 2.05H25BS004 1.07 0.16 0.00 0.00 0.00 0.00 1.32 2.55H25BS005 1.66 0.25 0.00 0.00 0.00 0.00 2.04 3.95H25CA020 11.40 2.54 7.76 1.30 0.00 0.00 12.57 35.57 13.84 2.59 10.27 1.71 0.00 0.00 18.53 46.94H25CA021 11.47 2.55 8.25 1.38 0.00 0.00 12.64 36.29 13.92 2.60 10.92 1.82 0.00 0.00 18.64 47.90H25CA022 13.07 4.01 12.58 2.10 0.00 0.00 16.47 48.23 15.68 4.05 16.64 2.78 0.00 0.00 23.48 62.63H25CA023 18.88 5.79 12.58 2.10 0.00 0.00 23.79 63.14 22.66 5.86 16.64 2.78 0.00 0.00 33.93 81.87H25CA034 3.50 0.74 1.77 0.30 0.00 0.00 3.85 10.16 4.00 0.75 2.34 0.39 0.00 0.00 5.03 12.51H25CA035 4.09 0.86 2.95 0.49 0.00 0.00 4.51 12.90 4.67 0.87 3.90 0.65 0.00 0.00 5.89 15.98H25CA036 6.57 1.39 4.62 0.77 0.00 0.00 7.25 20.60 7.51 1.40 6.11 1.02 0.00 0.00 9.46 25.50H25CA038 8.90 1.98 5.31 0.89 0.00 0.00 9.82 26.90 10.81 2.02 7.02 1.17 0.00 0.00 14.47 35.49H25CA040 8.73 2.68 12.28 2.05 0.00 0.00 11.00 36.74 10.48 2.71 16.25 2.71 0.00 0.00 15.69 47.84

2 224

EP 1110-1-8, Vol. 130 Nov 09

2-286


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

H25 cont.H25CA052 14.48 1.97 0.00 1.50 0.00 0.00 18.93 36.88H25CA053 19.66 2.67 0.00 1.60 0.00 0.00 25.70 49.63H25CA054 25.28 3.43 0.00 3.00 0.00 0.00 33.04 64.75H25CA055 2.75 0.37 0.00 0.40 0.00 0.00 3.60 7.12H25CA056 41.21 5.60 0.00 3.00 0.00 0.00 53.86 103.67H25CA057 11.53 1.57 0.00 0.80 0.00 0.00 15.07 28.97H25CA058 3.07 0.42 0.00 0.50 0.00 0.00 4.45 8.44H25CA059 11.19 1.52 0.00 0.60 0.00 0.00 16.25 29.56H25CA060 16.49 2.24 0.00 0.75 0.00 0.00 23.94 43.42H25CA061 14.39 1.95 0.00 0.75 0.00 0.00 20.89 37.98H25CA062 26.38 3.58 0.00 0.90 0.00 0.00 38.29 69.15H25CA063 18.84 2.56 0.00 0.90 0.00 0.00 27.36 49.66H25CA064 22.93 3.11 0.00 1.00 0.00 0.00 33.29 60.33H25KC016 13.85 3.08 9.24 1.54 0.00 0.00 15.28 42.99 16.82 3.14 12.22 2.04 0.00 0.00 22.52 56.74H25KC017 9.76 2.17 5.31 0.89 0.00 0.00 10.77 28.90 11.86 2.21 7.02 1.17 0.00 0.00 15.87 38.13H25KC019 15.28 4.68 14.05 2.34 0.00 0.00 19.25 55.60 18.34 4.74 18.59 3.10 0.00 0.00 27.45 72.22H25KC020 16.76 5.14 14.05 2.34 0.00 0.00 21.12 59.41 20.12 5.20 18.59 3.10 0.00 0.00 30.12 77.13H25KC021 17.73 5.43 17.30 2.89 0.00 0.00 22.34 65.69 21.28 5.50 22.87 3.82 0.00 0.00 31.86 85.33H25KC022 20.09 6.16 17.30 2.89 0.00 0.00 25.31 71.75 24.10 6.23 22.87 3.82 0.00 0.00 36.09 93.11H25KC023 25.02 7.67 23.39 3.90 0.00 0.00 31.53 91.51 30.03 7.76 30.93 5.16 0.00 0.00 44.96 118.84H25KC024 23.90 9.61 30.07 1.58 0.00 0.00 37.66 102.82 28.32 9.69 39.77 2.09 0.00 0.00 49.10 128.97H25KC026 25.04 10.06 30.96 1.63 0.00 0.00 39.46 107.15 29.68 10.16 40.94 2.16 0.00 0.00 51.44 134.38H25KM001 12.23 2.72 8.75 1.46 0.00 0.00 13.49 38.65 14.85 2.77 11.57 1.93 0.00 0.00 19.88 51.00H25KM003 18.90 4.21 10.81 1.80 0.00 0.00 20.84 56.56 22.95 4.29 14.30 2.39 0.00 0.00 30.72 74.65H25KM009 43.31 20.51 44.61 2.55 0.00 0.00 75.06 186.04 54.85 20.73 59.01 3.37 0.00 0.00 108.03 245.99H25KM015 42.91 17.25 37.74 1.99 0.00 0.00 67.63 167.52 50.86 17.40 49.91 2.63 0.00 0.00 88.15 208.95H25KM018 4.46 0.94 1.97 0.33 0.00 0.00 4.92 12.62 5.10 0.95 2.60 0.43 0.00 0.00 6.42 15.50

2 225

EP 1110-1-8, Vol. 130 Nov 09

2-287


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

H25 cont.H25KM021 6.00 1.26 3.83 0.64 0.00 0.00 6.62 18.35 6.86 1.28 5.07 0.85 0.00 0.00 8.64 22.70H25KM022 7.67 1.62 3.93 0.66 0.00 0.00 8.46 22.34 8.76 1.64 5.20 0.87 0.00 0.00 11.04 27.51H25KM023 9.46 1.99 5.31 0.89 0.00 0.00 10.43 28.08 10.81 2.02 7.02 1.17 0.00 0.00 13.62 34.64H25KM027 17.29 3.85 8.45 1.41 0.00 0.00 19.06 50.06 20.99 3.92 11.18 1.87 0.00 0.00 28.10 66.06H25KM033 86.77 41.10 89.23 5.10 0.00 0.00 150.40 372.60 109.90 41.54 118.01 6.74 0.00 0.00 216.44 492.63H25KN001 4.05 0.55 0.00 0.50 0.00 0.00 5.89 10.99H25KN002 5.62 0.76 0.00 0.50 0.00 0.00 8.16 15.04H25KN003 6.85 0.93 0.00 0.50 0.00 0.00 9.95 18.23H25KN004 7.88 1.07 0.00 0.50 0.00 0.00 11.44 20.89H25KN006 15.91 2.16 0.00 1.00 0.00 0.00 23.10 42.17H25KN007 0.82 0.11 0.00 0.15 0.00 0.00 1.18 2.26H25KN009 1.70 0.23 0.00 0.15 0.00 0.00 2.46 4.54H25KN010 2.34 0.32 0.00 0.15 0.00 0.00 3.40 6.21H25LI003 12.68 2.82 8.75 1.46 0.00 0.00 13.98 39.69 15.40 2.88 11.57 1.93 0.00 0.00 20.61 52.39H25LI005 14.82 3.30 9.93 1.66 0.00 0.00 16.35 46.06 18.00 3.36 13.13 2.19 0.00 0.00 24.10 60.78H25LU001 3.69 0.50 0.00 0.40 0.00 0.00 4.82 9.41H25LU002 4.15 0.56 0.00 0.50 0.00 0.00 5.43 10.64H25LU003 6.41 0.87 0.00 0.80 0.00 0.00 8.38 16.46H25LU004 7.46 1.01 0.00 0.90 0.00 0.00 9.75 19.12H25LU005 9.35 1.27 0.00 1.10 0.00 0.00 12.22 23.94H25LU006 13.10 1.78 0.00 1.50 0.00 0.00 17.12 33.50H25LU007 11.17 1.52 0.00 1.40 0.00 0.00 14.60 28.69H25LU008 14.61 1.98 0.00 1.60 0.00 0.00 19.10 37.29H25LU009 16.04 2.18 0.00 1.70 0.00 0.00 20.96 40.88H25LU010 19.27 2.62 0.00 2.00 0.00 0.00 25.19 49.08H25LU011 19.09 2.59 0.00 2.00 0.00 0.00 24.95 48.63H25LU012 23.37 3.17 0.00 2.50 0.00 0.00 30.55 59.59

2 226

EP 1110-1-8, Vol. 130 Nov 09

2-288


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

H25 cont.H25LU013 24.14 3.28 0.00 2.60 0.00 0.00 31.56 61.58H25LU014 28.10 3.82 0.00 3.00 0.00 0.00 36.73 71.65H25LU023 4.78 0.71 0.00 0.25 0.00 0.00 5.90 11.64H25LU024 2.38 0.35 0.00 0.30 0.00 0.00 2.94 5.97H25LU025 2.92 0.43 0.00 0.40 0.00 0.00 3.61 7.36H25LU026 3.33 0.49 0.00 0.50 0.00 0.00 4.10 8.42H25LU027 3.72 0.55 0.00 0.60 0.00 0.00 4.59 9.46H25LU028 6.15 0.91 0.00 0.70 0.00 0.00 7.58 15.34H25LU034 8.96 1.33 0.00 0.80 0.00 0.00 11.06 22.15H25LU035 10.73 1.60 0.00 0.90 0.00 0.00 13.24 26.47H25LU036 12.36 1.84 0.00 1.00 0.00 0.00 15.25 30.45H25LU040 19.93 2.71 0.00 0.75 0.00 0.00 28.93 52.32H25LU041 24.45 3.32 0.00 0.75 0.00 0.00 35.49 64.01H25LU042 29.49 4.01 0.00 1.50 0.00 0.00 42.81 77.81H25LU046 4.74 0.64 0.00 0.50 0.00 0.00 6.89 12.77H25LU047 5.45 0.74 0.00 0.60 0.00 0.00 7.92 14.71H25LU048 5.85 0.79 0.00 0.70 0.00 0.00 8.49 15.83H25LU049 7.06 0.96 0.00 0.80 0.00 0.00 10.25 19.07H25LU050 10.69 1.45 0.00 0.90 0.00 0.00 15.52 28.56H25LU053 20.97 2.85 0.00 0.75 0.00 0.00 30.45 55.02H25LU054 25.82 3.51 0.00 0.75 0.00 0.00 37.49 67.57H25ME001 2.73 0.58 1.31 0.22 0.00 0.00 3.01 7.85 3.12 0.58 1.73 0.29 0.00 0.00 3.94 9.66H25ME002 3.92 0.83 3.93 0.66 0.00 0.00 4.32 13.66 4.48 0.84 5.20 0.87 0.00 0.00 5.64 17.03H25ME003 5.45 1.15 4.72 0.79 0.00 0.00 6.01 18.12 6.23 1.16 6.24 1.04 0.00 0.00 7.84 22.51H25WN001 0.98 0.15 0.00 0.00 0.00 0.00 1.21 2.34H25WN002 1.11 0.15 0.00 0.00 0.00 0.00 1.61 2.87H25WN003 1.22 0.17 0.00 0.00 0.00 0.00 1.77 3.16

2 227

EP 1110-1-8, Vol. 130 Nov 09

2-289


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

H25 cont.H25WN004 1.33 0.18 0.00 0.00 0.00 0.00 1.93 3.44H25WN005 1.51 0.21 0.00 0.00 0.00 0.00 2.20 3.92

H30H30CA005 18.06 3.91 13.88 2.19 1.45 0.24 14.33 54.06 22.22 3.99 17.71 2.80 5.22 0.88 19.40 72.22H30CA007 15.01 3.31 11.12 1.76 1.99 0.33 11.97 45.49 18.47 3.38 14.19 2.24 7.17 1.20 16.20 62.85H30GA006 26.47 5.69 21.42 3.38 1.36 0.23 20.96 79.51 32.58 5.81 27.33 4.32 4.83 0.81 28.37 104.05H30GA007 18.63 4.00 12.69 2.00 0.84 0.14 14.74 53.04 22.92 4.08 16.19 2.56 2.97 0.50 19.96 69.18H30GA008 23.34 6.26 19.25 3.04 5.03 0.85 22.27 80.04 29.17 6.38 24.24 3.83 17.79 2.99 30.15 114.55H30KM001 17.96 4.71 11.31 1.79 0.90 0.15 17.04 53.86 22.45 4.80 14.43 2.28 3.23 0.54 23.07 70.80

H35H35HI006 67.52 24.55 62.99 3.60 0.00 0.00 119.67 278.33 77.16 24.74 83.31 4.76 0.00 0.00 148.15 338.12H35OK001 42.90 15.60 59.65 3.41 0.00 0.00 76.03 197.59 49.02 15.72 78.89 4.51 0.00 0.00 94.13 242.27H35OK003 86.97 31.62 100.04 5.71 0.00 0.00 154.15 378.49 99.39 31.87 132.31 7.56 0.00 0.00 190.83 461.96H35OK004 138.76 50.46 125.79 7.19 0.00 0.00 245.96 568.16 158.59 50.85 166.36 9.50 0.00 0.00 304.49 689.79H35OK005 261.56 95.11 221.11 12.63 0.00 0.00 463.61 1,054.02 298.92 95.86 292.43 16.70 0.00 0.00 573.93 1,277.84

L10L10BS002 2.31 0.54 0.00 0.30 0.00 0.00 3.22 6.37 3.30 0.56 0.00 0.30 0.00 0.00 5.12 9.28L10BS004 0.80 0.19 0.00 0.25 0.00 0.00 1.11 2.35 1.14 0.19 0.00 0.25 0.00 0.00 1.77 3.35L10BS005 2.11 0.50 0.00 0.30 0.00 0.00 2.95 5.86 3.02 0.51 0.00 0.30 0.00 0.00 4.68 8.51L10BS007 2.97 0.70 0.00 0.50 0.00 0.00 4.14 8.31 4.25 0.72 0.00 0.50 0.00 0.00 6.58 12.05L10BU005 0.75 0.18 0.00 1.10 0.00 0.00 1.05 3.08 1.08 0.18 0.00 1.10 0.00 0.00 1.67 4.03L10BU009 0.40 0.09 0.00 0.90 0.00 0.00 0.56 1.95 0.57 0.10 0.00 0.90 0.00 0.00 0.88 2.45L10BU010 0.38 0.09 0.00 0.80 0.00 0.00 0.53 1.80 0.55 0.09 0.00 0.80 0.00 0.00 0.85 2.29L10BU011 0.82 0.19 0.00 1.50 0.00 0.00 1.15 3.66 1.18 0.20 0.00 1.50 0.00 0.00 1.82 4.70L10BU012 1.69 0.40 0.00 2.00 0.00 0.00 2.35 6.44 2.41 0.41 0.00 2.00 0.00 0.00 3.74 8.56

2 228

EP 1110-1-8, Vol. 130 Nov 09

2-290


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

L10 cont.L10BU013 1.75 0.41 0.00 2.50 0.00 0.00 2.44 7.10 2.50 0.43 0.00 2.50 0.00 0.00 3.88 9.31L10RM001 4.11 0.96 0.00 0.40 0.00 0.00 5.73 11.20 5.87 1.00 0.00 0.40 0.00 0.00 9.09 16.36L10RM002 3.71 0.87 0.00 0.00 0.00 0.00 5.17 9.75 5.30 0.90 0.00 0.00 0.00 0.00 8.20 14.40L10VE002 1.80 0.43 5.69 0.81 0.07 0.01 2.52 11.33 2.58 0.45 7.37 1.05 0.23 0.04 4.01 15.73L10VE005 0.95 0.23 2.11 0.30 0.06 0.01 1.33 4.99 1.36 0.24 2.74 0.39 0.20 0.03 2.12 7.08L10VE006 2.53 0.60 3.25 0.46 0.06 0.01 3.54 10.45 3.62 0.62 4.21 0.60 0.20 0.03 5.62 14.90L10VE007 2.21 0.52 0.00 1.50 0.00 0.00 3.07 7.30 3.15 0.54 0.00 1.50 0.00 0.00 4.88 10.07L10VE009 2.86 0.68 7.17 0.89 0.06 0.01 3.99 15.66 4.08 0.70 9.15 1.13 0.20 0.03 6.33 21.62L10VE010 0.99 0.24 4.39 0.63 0.03 0.01 1.38 7.67 1.42 0.24 5.69 0.81 0.10 0.02 2.20 10.48

L15L15BW001 3.42 0.34 5.42 0.62 0.08 0.01 3.49 13.38L15BW002 6.16 0.61 7.59 0.86 0.17 0.03 6.28 21.70L15BW003 7.10 0.70 10.84 1.23 0.17 0.03 7.23 27.30L15BW004 10.30 1.00 10.84 1.23 0.00 0.00 10.47 33.84L15FG001 39.38 3.83 19.75 2.25 0.00 0.00 40.03 105.24L15FG002 8.93 0.88 13.85 1.58 0.12 0.02 9.10 34.48L15HZ001 0.17 0.02 0.65 0.07 0.00 0.00 0.17 1.08L15JD001 1.61 0.23 4.33 0.49 1.54 0.26 1.75 10.21L15JD005 0.47 0.05 0.00 0.00 0.00 0.00 0.48 1.00L15JD006 0.87 0.08 0.00 0.00 0.00 0.00 0.88 1.83L15TO001 0.28 0.03 1.30 0.15 0.00 0.00 0.28 2.04L15TO002 0.75 0.08 3.25 0.37 0.18 0.03 0.78 5.44L15TO003 1.53 0.16 4.55 0.52 0.18 0.03 1.57 8.54L15TO004 1.65 0.17 4.55 0.52 0.16 0.03 1.69 8.77L15TO006 3.06 0.31 6.28 0.71 0.30 0.05 3.13 13.84L15TO007 3.16 0.32 6.28 0.71 0.30 0.05 3.23 14.05L15WI001 1.64 0.17 0.00 0.05 0.10 0.02 1.68 3.66

2 229

EP 1110-1-8, Vol. 130 Nov 09

2-291


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

L20L20AB017 1.32 0.26 1.74 0.20 0.06 0.01 3.06 6.65L20AB018 1.47 0.29 1.86 0.21 0.06 0.01 3.41 7.31L20AB019 1.73 0.34 1.86 0.21 0.06 0.01 4.01 8.22L20AB020 1.11 0.22 1.49 0.17 0.06 0.01 2.57 5.63L20AB021 1.17 0.23 1.86 0.21 0.06 0.01 2.72 6.26L20AB022 1.32 0.26 1.74 0.20 0.06 0.01 3.08 6.67L20AB023 0.54 0.11 0.00 0.00 0.04 0.01 1.25 1.95L20AB024 0.58 0.11 0.00 0.00 0.04 0.01 1.35 2.09

L25L25JE001 1.15 0.22 3.01 0.34 0.00 0.00 2.14 6.86L25JE002 9.71 1.88 29.89 3.40 0.32 0.05 18.03 63.28L25MB002 0.49 0.12 1.16 1.13 0.31 0.05 0.95 4.21L25MB004 15.12 2.92 44.04 6.51 0.32 0.05 28.04 97.00L25MB005 0.99 0.21 2.32 1.26 0.31 0.05 1.88 7.02L25MB006 9.26 1.77 13.91 2.83 0.00 0.00 17.14 44.91L25MB007 5.20 1.00 5.33 1.61 0.00 0.00 9.62 22.76L25MB008 16.30 3.19 24.69 4.31 0.91 0.15 30.31 79.86

L30L30HW015 11.05 2.65 2.31 1.23 0.69 0.12 17.13 35.18 13.82 2.71 3.02 1.61 2.21 0.37 23.56 47.30L30KB001 2.60 0.63 1.38 0.74 0.23 0.04 4.04 9.66 3.25 0.64 1.81 0.97 0.74 0.12 5.56 13.09L30KB002 2.74 0.66 1.38 0.74 0.23 0.04 4.26 10.05 3.43 0.68 1.81 0.97 0.74 0.12 5.86 13.61L30RA001 5.72 1.36 2.46 0.33 0.25 0.04 8.85 19.01 7.14 1.39 3.25 0.43 0.80 0.13 12.17 25.31L30S4001 1.48 0.35 1.38 0.74 0.00 0.00 2.28 6.23 1.85 0.35 1.81 0.97 0.00 0.00 3.13 8.11L30S4002 1.69 0.40 0.00 0.00 0.00 0.00 2.60 4.69 2.11 0.40 0.00 0.00 0.00 0.00 3.58 6.09L30S4003 0.12 0.03 0.00 0.00 0.00 0.00 0.19 0.34 0.16 0.03 0.00 0.00 0.00 0.00 0.26 0.45

2 230

EP 1110-1-8, Vol. 130 Nov 09

2-292


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

L30 cont.L30S4004 0.21 0.05 0.00 0.00 0.00 0.00 0.32 0.58 0.26 0.05 0.00 0.00 0.00 0.00 0.45 0.76L30TS001 2.84 0.71 1.11 0.59 0.53 0.09 4.44 10.31 3.55 0.72 1.45 0.77 1.67 0.28 6.10 14.54

L35L35CA005 16.21 3.80 15.95 1.80 0.00 0.00 27.62 65.38 20.26 3.88 20.64 2.33 0.00 0.00 39.21 86.32L35CA007 30.57 7.17 26.08 2.95 0.00 0.00 52.09 118.86 38.22 7.32 33.75 3.82 0.00 0.00 73.95 157.06L35CA013 9.86 2.31 9.70 1.10 0.00 0.00 16.80 39.77 12.33 2.36 12.55 1.42 0.00 0.00 23.85 52.51L35CA014 22.12 5.19 17.24 1.95 0.00 0.00 37.69 84.19 27.65 5.30 22.32 2.52 0.00 0.00 53.51 111.30L35KM006 36.01 8.44 21.56 2.44 0.00 0.00 61.35 129.80 45.01 8.62 27.90 3.16 0.00 0.00 87.10 171.79

L40L40CA007 26.14 8.59 29.48 2.64 11.88 2.00 28.68 109.41 29.41 8.65 38.99 3.49 42.75 7.18 34.57 165.04L40CA009 89.22 29.79 78.62 7.04 20.94 3.52 98.20 327.33 100.37 30.02 103.98 9.32 75.39 12.67 118.38 450.13L40CA012 13.79 3.61 14.25 1.77 1.04 0.17 19.43 54.06 14.91 3.64 18.85 2.34 3.75 0.63 22.25 66.37L40CA013 8.59 2.27 8.84 1.10 1.00 0.17 12.13 34.10 9.29 2.28 11.70 1.45 3.58 0.60 13.88 42.78L40CA014 19.21 5.03 19.65 2.44 1.35 0.23 27.05 74.96 20.76 5.06 25.99 3.23 4.85 0.81 30.97 91.67L40CA015 10.95 2.68 14.64 1.82 1.04 0.17 12.72 44.02 11.57 2.69 19.37 2.41 3.75 0.63 15.36 55.78L40CA018 65.38 21.54 60.73 5.44 12.60 2.12 71.76 239.57 73.55 21.71 80.32 7.20 45.35 7.62 86.51 322.26L40CA019 7.91 1.95 9.34 1.16 1.00 0.17 9.20 30.73 8.36 1.96 12.35 1.54 3.58 0.60 11.12 39.51L40CA022 11.04 2.70 12.58 1.56 1.04 0.17 12.83 41.92 11.68 2.72 16.64 2.07 3.75 0.63 15.50 52.99L40CA023 13.20 3.30 17.69 2.20 2.71 0.46 15.41 54.97 13.95 3.32 23.39 2.91 9.76 1.64 18.62 73.59L40CA024 16.53 4.16 19.36 2.41 3.96 0.67 19.33 66.42 17.47 4.18 25.60 3.18 14.26 2.40 23.36 90.45L40CA025 17.60 4.42 20.73 2.58 3.96 0.67 20.56 70.52 18.60 4.44 27.42 3.41 14.26 2.40 24.85 95.38L40CA028 2.92 0.59 5.28 0.66 0.86 0.14 3.66 14.11L40CA029 3.25 0.65 5.82 0.72 0.86 0.14 4.07 15.51L40CA030 3.65 0.74 6.36 0.79 1.19 0.20 4.58 17.51L40CA031 3.55 0.72 7.98 0.99 1.19 0.20 4.45 19.08L40CA032 3.59 0.91 5.11 0.64 0.57 0.10 4.20 15.12 3.80 0.91 6.76 0.84 2.06 0.35 5.08 19.80

2 231

EP 1110-1-8, Vol. 130 Nov 09

2-293


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

L40 cont.L40CA033 4.77 1.19 6.68 0.83 0.57 0.10 5.56 19.70 5.04 1.19 8.84 1.10 2.06 0.35 6.72 25.30L40CA034 5.33 1.39 7.47 0.93 2.98 0.50 6.29 24.89 5.64 1.40 9.88 1.23 10.72 1.80 7.60 38.27L40CS009 12.23 3.03 13.36 1.66 1.92 0.32 14.25 46.77 12.93 3.04 17.68 2.20 6.92 1.16 17.22 61.15L40CS010 14.65 3.61 17.79 2.21 1.92 0.32 17.04 57.54 15.49 3.63 23.52 2.92 6.92 1.16 20.59 74.23L40CS011 18.20 4.56 18.38 2.29 3.96 0.67 21.26 69.32 19.24 4.58 24.30 3.02 14.26 2.40 25.69 93.49L40KM003 11.80 2.90 13.66 1.70 1.26 0.21 13.71 45.24 12.48 2.91 18.07 2.25 4.53 0.76 16.57 57.57L40KM008 26.13 8.58 32.92 2.95 7.60 1.28 28.66 108.12 29.39 8.65 43.54 3.90 27.36 4.60 34.55 151.99L40KM009 37.21 12.38 48.15 4.31 8.28 1.39 40.92 152.64 41.86 12.47 63.69 5.71 29.80 5.01 49.33 207.87L40KM010 60.78 20.12 67.22 6.02 12.60 2.12 66.78 235.64 68.38 20.28 88.90 7.97 45.35 7.62 80.50 319.00L40KM011 76.49 25.85 83.82 7.51 20.94 3.52 84.41 302.54 86.06 26.05 110.86 9.93 75.39 12.67 101.75 422.71L40KM015 6.79 1.70 7.37 0.92 0.95 0.16 7.93 25.82 7.18 1.71 9.75 1.21 3.42 0.57 9.59 33.43L40ME012 2.59 0.51 4.96 0.62 0.38 0.06 3.23 12.35L40ME016 1.58 0.31 2.53 0.31 0.31 0.05 1.97 7.06L40ME017 1.94 0.39 3.83 0.48 0.50 0.08 2.43 9.65L40ME021 2.17 0.45 5.28 0.66 0.84 0.14 2.73 12.27L40ME022 3.26 0.65 8.08 1.00 0.84 0.14 4.07 18.04L40ME023 3.63 0.73 8.73 1.09 0.84 0.14 4.54 19.70

L50L50CA001 4.40 1.19 5.93 2.93 0.72 0.12 5.88 21.17 7.33 1.25 8.41 4.15 2.57 0.43 10.42 34.56L50CA004 10.66 2.86 8.37 4.13 1.29 0.22 14.22 41.75 17.76 3.01 11.86 5.86 4.57 0.77 25.18 69.01L50CS005 6.72 1.81 6.85 3.38 0.93 0.16 8.97 28.82 11.20 1.90 9.70 4.79 3.31 0.56 15.89 47.35L50CS006 8.09 2.18 7.46 3.68 1.10 0.18 10.79 33.48 13.48 2.28 10.56 5.22 3.92 0.66 19.12 55.24L50JC001 5.17 1.37 5.10 2.52 0.45 0.08 6.87 21.56 8.61 1.44 7.22 3.57 1.63 0.27 12.16 34.90L50JC002 5.76 1.56 7.00 3.46 0.92 0.15 7.71 26.56 9.60 1.64 9.92 4.90 3.27 0.55 13.65 43.53L50JC003 6.98 1.89 7.61 3.76 1.24 0.21 9.34 31.03 11.64 1.99 10.78 5.32 4.47 0.75 16.54 51.49L50JC005 8.14 2.19 7.61 3.76 1.24 0.21 10.88 34.03 13.57 2.31 10.78 5.32 4.47 0.75 19.26 56.46L50JC007 10.47 2.81 7.61 3.76 1.39 0.23 13.96 40.23 17.45 2.95 10.78 5.32 4.99 0.84 24.72 67.05

2 232

EP 1110-1-8, Vol. 130 Nov 09

2-294


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

L55L55KN001 0.91 0.14 0.00 0.52 0.00 0.00 1.41 2.98L55KN002 1.87 0.28 0.00 1.06 0.00 0.00 2.89 6.10L55KN004 1.73 0.26 0.00 0.00 0.00 0.00 2.68 4.67L55KN005 2.56 0.38 0.00 0.00 0.00 0.00 3.95 6.89L55KN006 3.82 0.57 0.00 0.00 0.00 0.00 5.89 10.28

L60L60CA010 27.81 5.94 14.74 1.96 0.00 0.00 29.42 79.87 34.77 6.07 19.50 2.59 0.00 0.00 42.05 104.98L60CA011 33.27 7.10 14.74 1.96 0.00 0.00 35.19 92.26 41.59 7.26 19.50 2.59 0.00 0.00 50.29 121.23L60CA013 18.63 4.14 15.72 2.09 2.25 0.38 19.83 63.04 23.29 4.23 20.80 2.77 7.86 1.32 28.34 88.61L60CA014 24.24 5.18 11.79 1.57 0.00 0.00 25.63 68.41 30.30 5.29 15.60 2.08 0.00 0.00 36.64 89.91L60JD001 12.26 2.79 11.69 1.56 2.89 0.49 13.10 44.78 15.33 2.85 15.47 2.06 10.39 1.75 18.72 66.57L60JD002 14.68 3.31 14.84 1.97 2.89 0.49 15.66 53.84 18.36 3.38 19.63 2.61 10.39 1.75 22.38 78.50L60JD003 11.95 2.72 11.69 1.56 2.89 0.49 12.77 44.07 14.94 2.78 15.47 2.06 10.39 1.75 18.25 65.64L60JD004 15.64 3.61 15.72 2.09 4.52 0.76 16.74 59.08 19.55 3.69 20.80 2.77 16.29 2.74 23.93 89.77L60JD006 19.34 4.36 16.71 2.22 3.85 0.65 20.63 67.76 24.18 4.46 22.09 2.94 13.86 2.33 29.48 99.34L60JD007 21.25 4.77 19.65 2.61 3.85 0.65 22.65 75.43 26.57 4.87 25.99 3.46 13.86 2.33 32.38 109.46L60JD008 29.34 6.27 16.71 2.22 0.00 0.00 31.03 85.57 36.67 6.40 22.09 2.94 0.00 0.00 44.35 112.45

M10M10MZ001 2.76 0.34 0.00 0.00 0.00 0.00 1.93 5.03M10MZ003 3.40 0.42 0.00 0.00 0.00 0.00 2.37 6.19M10MZ005 0.78 0.43 0.00 0.00 0.00 0.00 0.66 1.87M10MZ007 0.81 0.44 0.00 0.00 0.00 0.00 0.68 1.93M10MZ010 2.56 0.85 13.76 2.48 0.00 0.00 2.66 22.31 3.16 0.86 18.20 3.29 0.00 0.00 3.50 29.01M10MZ011 3.66 1.21 20.64 3.73 0.00 0.00 3.80 33.04 4.51 1.22 27.29 4.93 0.00 0.00 5.01 42.96M10SM001 3.04 1.00 26.64 4.05 0.00 0.00 3.15 37.88 3.74 1.01 34.77 5.28 0.00 0.00 4.15 48.95

2 233

EP 1110-1-8, Vol. 130 Nov 09

2-295


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

M10 cont.M10SM003 3.77 1.24 35.52 5.39 0.00 0.00 3.91 49.83 4.64 1.26 46.35 7.04 0.00 0.00 5.15 64.44M10SM004 4.05 1.34 44.40 6.74 0.00 0.00 4.20 60.73 4.98 1.35 57.94 8.80 0.00 0.00 5.53 78.60M10SM005 1.40 0.46 20.42 3.10 0.00 0.00 1.45 26.83 1.73 0.47 26.65 4.05 0.00 0.00 1.92 34.82M10SM008 2.55 0.84 35.52 5.39 0.00 0.00 2.64 46.94 3.13 0.85 46.35 7.04 0.00 0.00 3.48 60.85M10XX001 0.18 0.10 0.00 0.00 0.00 0.00 0.15 0.43M10XX002 0.57 0.31 0.00 0.00 0.00 0.00 0.48 1.36M10XX003 0.69 0.38 0.00 0.00 0.00 0.00 0.58 1.65M10XX004 1.12 0.61 0.00 0.00 0.00 0.00 0.94 2.67M10XX005 1.70 2.46 0.00 0.00 0.00 0.00 1.35 5.51M10XX006 2.39 3.46 0.00 0.00 0.00 0.00 1.90 7.75M10XX007 3.04 4.40 0.00 0.00 0.00 0.00 2.42 9.86M10XX008 4.22 6.10 0.00 0.00 0.00 0.00 3.36 13.68M10XX009 0.77 0.25 8.88 1.35 0.00 0.00 0.80 12.05 0.94 0.26 11.59 1.76 0.00 0.00 1.05 15.60M10XX010 2.56 0.84 7.37 1.33 0.00 0.00 2.65 14.75 3.15 0.86 9.75 1.76 0.00 0.00 3.50 19.02M10XX011 2.94 0.97 9.83 1.77 0.00 0.00 3.05 18.56 3.62 0.98 13.00 2.35 0.00 0.00 4.02 23.97M10XX012 3.00 0.99 9.83 1.77 0.00 0.00 3.11 18.70 3.69 1.00 13.00 2.35 0.00 0.00 4.10 24.14M10XX013 3.88 1.28 11.30 2.04 0.00 0.00 4.03 22.53 4.78 1.30 14.95 2.70 0.00 0.00 5.31 29.04M10XX014 5.34 1.76 17.20 3.11 0.00 0.00 5.54 32.95 6.58 1.79 22.74 4.11 0.00 0.00 7.31 42.53M10XX015 6.70 2.21 24.57 4.44 0.00 0.00 6.95 44.87 8.25 2.24 32.49 5.87 0.00 0.00 9.16 58.01M10XX016 7.62 3.77 0.00 0.00 0.00 0.00 7.07 18.46M10XX017 8.06 3.99 0.00 0.00 0.00 0.00 7.47 19.52M10XX018 10.03 4.97 0.00 0.00 0.00 0.00 9.30 24.30M10XX019 10.25 5.08 0.00 0.00 0.00 0.00 9.51 24.84M10XX021 16.73 5.60 37.34 6.74 0.00 0.00 18.72 85.13 20.07 5.67 49.39 8.92 0.00 0.00 23.86 107.91M10XX022 19.03 6.38 42.75 7.72 0.00 0.00 21.30 97.18 22.84 6.45 56.54 10.21 0.00 0.00 27.16 123.20M10XX023 25.49 8.54 39.31 7.10 0.00 0.00 28.52 108.96 30.59 8.64 51.99 9.39 0.00 0.00 36.37 136.98M10XX024 36.35 12.17 42.75 7.72 0.00 0.00 40.67 139.66 43.62 12.32 56.54 10.21 0.00 0.00 51.86 174.55

2 234

EP 1110-1-8, Vol. 130 Nov 09

2-296


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

P10P10IC001 11.79 2.34 17.20 2.61 0.00 0.00 17.91 51.85P10IC002 18.57 3.68 29.48 4.48 0.00 0.00 28.19 84.40P10IC005 49.50 9.81 78.62 11.94 0.00 0.00 75.16 225.03P10IC010 1.75 0.35 0.00 0.00 0.00 0.00 2.65 4.75P10IC011 3.44 0.68 1.28 0.19 0.00 0.00 5.22 10.81P10IC012 2.47 0.49 0.00 0.00 0.00 0.00 3.75 6.71P10IC013 4.27 0.85 2.31 0.35 0.00 0.00 6.48 14.26

P20P20IC002 12.35 2.01 0.00 1.90 0.00 0.00 22.37 38.63P20IC003 12.56 2.05 0.00 2.50 0.00 0.00 22.74 39.85P20IC004 13.41 2.18 0.00 3.15 0.00 0.00 24.28 43.02P20MK001 7.52 1.22 0.00 1.25 0.00 0.00 13.62 23.61P20MK002 2.39 0.36 0.00 0.50 0.00 0.00 4.06 7.31P20MK003 3.02 0.45 0.00 1.00 0.00 0.00 5.12 9.59P20MK004 3.74 0.56 0.00 1.25 0.00 0.00 6.35 11.90P20MK005 6.30 0.94 0.00 1.25 0.00 0.00 10.69 19.18P20MK006 6.98 1.04 0.00 2.50 0.00 0.00 11.84 22.36P20MK007 7.64 1.14 0.00 2.50 0.00 0.00 12.97 24.25

P25P25DL001 7.23 1.07 0.00 0.95 0.00 0.00 11.15 20.40P25DL003 8.67 1.29 0.00 1.20 0.00 0.00 13.37 24.53P25DL004 9.91 1.47 0.00 1.80 0.00 0.00 15.29 28.47P25DL005 13.65 2.03 0.00 2.65 0.00 0.00 21.05 39.38P25DL006 14.14 2.10 0.00 3.30 0.00 0.00 21.80 41.34P25DL008 17.40 2.59 0.00 5.30 0.00 0.00 26.84 52.13

2 235

EP 1110-1-8, Vol. 130 Nov 09

2-297


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

P25 cont.P25DL009 26.20 3.89 0.00 6.60 0.00 0.00 40.42 77.11P25DL010 38.20 5.68 0.00 8.25 0.00 0.00 58.92 111.05P25DL011 40.80 6.06 0.00 9.90 0.00 0.00 62.93 119.69P25IC001 9.02 1.34 0.00 2.20 0.00 0.00 13.91 26.47P25IC002 10.04 1.49 0.00 3.45 0.00 0.00 15.48 30.46P25IC003 14.45 2.15 0.00 4.40 0.00 0.00 22.29 43.29P25IC004 16.06 2.39 0.00 5.30 0.00 0.00 24.77 48.52P25IC005 19.97 2.97 0.00 6.25 0.00 0.00 30.81 60.00P25IC006 24.67 3.67 0.00 7.20 0.00 0.00 38.06 73.60P25MK001 8.85 1.32 0.00 2.50 0.00 0.00 13.66 26.33P25MK003 14.69 2.18 0.00 4.15 0.00 0.00 22.65 43.67P25VU002 10.00 1.36 0.00 2.50 0.00 0.00 14.52 28.38P25VU003 12.29 1.67 0.00 2.50 0.00 0.00 17.84 34.30P25VU004 12.56 1.71 0.00 2.50 0.00 0.00 18.23 35.00P25VU005 16.89 2.29 0.00 2.50 0.00 0.00 24.52 46.20P25VU010 17.37 2.36 0.00 0.95 0.00 0.00 25.21 45.89P25VU011 17.59 2.39 0.00 1.17 0.00 0.00 25.53 46.68

P30P30MK001 12.58 1.87 18.18 2.76 0.00 0.00 19.41 54.80P30MK003 21.72 3.23 31.94 4.85 0.00 0.00 33.50 95.24P30MK004 36.71 5.46 61.91 9.40 0.00 0.00 56.63 170.11

P35P35CA001 12.60 4.04 5.93 1.13 0.00 0.00 18.53 42.23 15.33 4.09 7.67 1.46 0.00 0.00 26.13 54.68P35CA006 39.35 12.62 22.63 4.31 0.00 0.00 57.89 136.80 47.90 12.78 29.29 5.58 0.00 0.00 81.61 177.16P35CA008 23.30 7.47 12.39 2.36 0.00 0.00 34.28 79.80 28.37 7.57 16.04 3.05 0.00 0.00 48.33 103.36P35CA009 30.30 9.71 16.44 3.13 0.00 0.00 44.57 104.15 36.88 9.84 21.27 4.05 0.00 0.00 62.84 134.88

2 236

EP 1110-1-8, Vol. 130 Nov 09

2-298


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

P40P40BX001 1.48 0.24 0.00 0.05 0.00 0.00 1.56 3.33P40TE003 9.78 1.61 2.43 0.32 1.25 0.21 10.30 25.90P40TE004 11.34 1.85 3.35 0.45 1.03 0.17 11.93 30.12P40TE005 8.58 1.41 5.02 0.67 1.25 0.21 9.03 26.17P40TE006 11.61 1.89 5.02 0.67 1.12 0.19 12.22 32.72P40TE007 19.55 3.16 5.02 0.67 1.12 0.19 20.55 50.26P40TE008 21.77 3.52 5.78 0.77 1.12 0.19 22.89 56.04P40TE009 24.30 3.92 5.78 0.77 1.12 0.19 25.54 61.62P40TE010 8.26 1.34 15.98 2.13 0.61 0.10 8.69 37.11P40TE011 9.00 1.48 15.98 2.13 1.06 0.18 9.48 39.31P40TE012 13.62 2.22 15.98 2.13 1.06 0.18 14.33 49.52P40TE013 12.44 2.03 15.98 2.13 1.06 0.18 13.09 46.91P40TE014 12.69 2.07 15.98 2.13 1.06 0.18 13.35 47.46P40TE015 14.43 2.35 15.98 2.13 1.06 0.18 15.18 51.31

P45P45AF002 0.09 0.02 0.00 0.00 0.00 0.00 0.13 0.24P45AF003 0.12 0.02 0.00 0.00 0.00 0.00 0.18 0.32P45AF005 1.21 0.22 2.85 0.43 0.08 0.01 1.77 6.57P45AF006 1.58 0.28 2.85 0.43 0.08 0.01 2.31 7.54P45AF007 3.50 0.62 4.28 0.57 0.06 0.01 5.09 14.13P45AF008 0.81 0.14 0.00 0.10 0.00 0.00 1.18 2.23P45AF009 2.72 0.47 0.00 0.10 0.00 0.00 3.94 7.23P45AF010 3.16 0.56 4.66 0.71 0.08 0.01 4.60 13.78P45AF011 5.66 0.99 9.06 1.38 0.08 0.01 8.22 25.40P45AL015 6.31 1.11 6.56 0.87 0.08 0.01 9.16 24.10P45CG001 0.43 0.08 0.00 0.05 0.00 0.00 0.63 1.19

2 237

EP 1110-1-8, Vol. 130 Nov 09

2-299


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

P45 cont.P45CG002 0.70 0.12 0.00 0.10 0.00 0.00 1.02 1.94P45CG003 1.63 0.28 0.00 0.15 0.00 0.00 2.36 4.42P45CG006 2.93 0.52 4.14 0.63 0.08 0.01 4.26 12.57P45CG007 2.38 0.42 4.14 0.63 0.00 0.00 3.45 11.02P45OE002 3.60 0.64 7.85 1.04 0.14 0.02 5.24 18.53P45OE003 4.69 0.83 11.98 1.59 0.14 0.02 6.83 26.08P45OE004 5.62 0.99 17.12 2.28 0.14 0.02 8.18 34.35P45OE005 7.54 1.34 25.82 3.44 0.28 0.05 10.97 49.44

P50P50GR001 0.05 0.00 0.00 0.00 0.00 0.00 0.09 0.14P50GR002 0.08 0.01 0.00 0.00 0.00 0.00 0.16 0.25P50GR003 0.11 0.01 0.00 0.00 0.00 0.00 0.23 0.35P50GR004 0.25 0.02 0.00 0.00 0.00 0.00 0.52 0.79P50GR005 0.08 0.01 0.00 0.00 0.00 0.00 0.17 0.26P50GR006 0.16 0.01 0.00 0.00 0.00 0.00 0.33 0.50P50GR007 0.26 0.02 0.00 0.00 0.00 0.00 0.54 0.82P50GR008 0.56 0.05 0.00 0.00 0.00 0.00 1.15 1.76P50WC001 0.13 0.03 2.44 0.37 0.00 0.00 0.19 3.16P50WC002 0.16 0.03 2.04 0.37 0.00 0.00 0.22 2.82P50WC003 0.37 0.07 2.18 0.39 0.00 0.00 0.51 3.52P50WC004 1.69 0.33 4.50 0.81 0.04 0.01 2.35 9.73P50XX001 2.40 0.46 8.18 1.48 0.00 0.00 3.34 15.86P50XX002 4.44 0.85 9.54 1.72 0.00 0.00 6.16 22.71P50XX003 4.76 0.91 11.59 2.09 0.00 0.00 6.61 25.96

P55P55GF001 2.09 0.40 2.86 0.52 0.00 0.00 3.22 9.09

2 238

EP 1110-1-8, Vol. 130 Nov 09

2-300


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

P55 cont.P55GF002 2.32 0.44 9.81 1.77 0.00 0.00 3.58 17.92P55GR001 0.41 0.07 0.26 0.14 0.00 0.00 0.36 1.24P55GR002 0.50 0.09 0.64 0.34 0.00 0.00 0.44 2.01P55GR003 1.60 0.28 3.20 1.71 0.00 0.00 1.40 8.19P55GR004 2.41 0.42 7.67 4.10 0.00 0.00 2.10 16.70P55WC001 0.04 0.01 0.13 0.07 0.00 0.00 0.04 0.29P55WC002 0.06 0.01 0.13 0.07 0.00 0.00 0.05 0.32

P60P60GF003 2.33 0.45 2.86 0.52 0.08 0.01 3.24 9.49P60GF004 2.56 0.50 9.81 1.77 0.08 0.01 3.56 18.29P60GF005 2.95 0.57 15.40 2.78 0.08 0.01 4.11 25.90P60GF006 4.60 0.89 19.08 3.44 0.09 0.02 6.40 34.52P60GF008 2.56 0.50 9.81 1.77 0.08 0.01 3.56 18.29P60GR001 2.43 0.47 6.41 1.16 0.07 0.01 3.38 13.93P60GR002 2.84 0.55 24.62 3.74 0.07 0.01 3.95 35.78P60HO002 0.09 0.02 0.85 0.13 0.00 0.00 0.13 1.22P60HO003 0.16 0.03 1.95 0.30 0.00 0.00 0.23 2.67P60WC001 0.07 0.01 0.98 0.15 0.00 0.00 0.09 1.30P60WC002 0.09 0.02 1.46 0.22 0.00 0.00 0.12 1.91

P65P65GR001 0.36 0.08 1.22 0.19 0.17 0.03 0.46 2.51P65GR002 0.43 0.10 0.37 0.06 0.17 0.03 0.55 1.71P65GR003 1.17 0.24 0.73 0.11 0.14 0.02 1.46 3.87P65HO001 0.17 0.03 0.85 0.13 0.00 0.00 0.23 1.41P65HO002 0.19 0.04 0.85 0.13 0.00 0.00 0.27 1.48P65WC001 0.17 0.03 0.98 0.15 0.00 0.00 0.21 1.54

2 239

EP 1110-1-8, Vol. 130 Nov 09

2-301


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

P65 cont.P65WC002 0.19 0.04 0.98 0.15 0.00 0.00 0.23 1.59

P70P70XX001 0.32 0.07 0.49 0.07 0.00 0.00 0.42 1.37P70XX002 0.82 0.17 1.46 0.22 0.00 0.00 1.08 3.75

R10R10CA001 1.05 0.20 0.00 0.08 0.00 0.00 1.46 2.79 1.29 0.21 0.00 0.08 0.00 0.00 2.00 3.58R10CA003 1.05 0.20 0.00 0.08 0.00 0.00 1.46 2.79 1.29 0.21 0.00 0.08 0.00 0.00 2.00 3.58R10CA005 1.05 0.20 0.00 0.08 0.00 0.00 1.46 2.79 1.29 0.21 0.00 0.08 0.00 0.00 2.00 3.58R10CA006 0.03 0.01 0.00 0.00 0.00 0.00 0.04 0.08 0.03 0.01 0.00 0.00 0.00 0.00 0.05 0.09R10CA007 2.41 0.46 0.00 0.08 0.00 0.00 3.36 6.31 2.97 0.47 0.00 0.08 0.00 0.00 4.60 8.12R10CA009 4.49 0.86 0.00 0.08 0.00 0.00 6.26 11.69 5.53 0.88 0.00 0.08 0.00 0.00 8.56 15.05R10CA010 0.18 0.03 0.00 0.00 0.00 0.00 0.25 0.46 0.22 0.04 0.00 0.00 0.00 0.00 0.34 0.60R10CA011 4.88 0.94 0.00 0.10 0.00 0.00 6.81 12.73 6.01 0.96 0.00 0.10 0.00 0.00 9.31 16.38R10CA012 5.76 1.10 0.00 0.10 0.00 0.00 8.03 14.99 7.09 1.13 0.00 0.10 0.00 0.00 10.98 19.30R10CA013 0.40 0.08 0.00 0.00 0.00 0.00 0.56 1.04 0.49 0.08 0.00 0.00 0.00 0.00 0.77 1.34R10CA014 6.28 1.20 0.00 0.16 0.00 0.00 8.75 16.39 7.73 1.23 0.00 0.16 0.00 0.00 11.97 21.09R10CA015 7.15 1.37 0.00 0.16 0.00 0.00 9.97 18.65 8.80 1.40 0.00 0.16 0.00 0.00 13.63 23.99R10CA016 0.40 0.08 0.00 0.00 0.00 0.00 0.56 1.04 0.50 0.08 0.00 0.00 0.00 0.00 0.77 1.35R10CA017 9.57 1.83 0.00 0.21 0.00 0.00 13.33 24.94 11.77 1.88 0.00 0.21 0.00 0.00 18.23 32.09R10CA018 11.42 2.19 0.00 0.22 0.00 0.00 15.91 29.74 14.05 2.24 0.00 0.22 0.00 0.00 21.76 38.27R10CA019 0.66 0.13 0.00 0.24 0.00 0.00 0.92 1.95 0.81 0.13 0.00 0.24 0.00 0.00 1.25 2.43R10CA020 11.56 2.22 0.00 0.23 0.00 0.00 16.12 30.13 14.23 2.27 0.00 0.23 0.00 0.00 22.04 38.77R10CA021 11.94 2.29 0.00 0.25 0.00 0.00 16.64 31.12 14.69 2.34 0.00 0.25 0.00 0.00 22.76 40.04R10CA022 0.11 0.02 0.00 0.00 0.00 0.00 0.15 0.28 0.14 0.02 0.00 0.00 0.00 0.00 0.21 0.37R10CA023 0.11 0.02 0.00 0.00 0.00 0.00 0.16 0.29 0.14 0.02 0.00 0.00 0.00 0.00 0.21 0.37

2 240

EP 1110-1-8, Vol. 130 Nov 09

2-302


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

R15R15SO001 9.68 2.51 0.00 0.40 1.33 0.22 11.10 25.24R15SO002 9.53 2.76 0.00 0.45 2.96 0.50 11.22 27.42R15SO003 14.15 3.85 0.00 0.67 2.96 0.50 16.40 38.53

R20R20RI002 2.69 0.63 0.00 0.25 0.00 0.00 3.45 7.02R20SO001 5.94 1.39 0.00 0.25 0.00 0.00 7.63 15.21

R30R30BO003 14.47 2.65 13.25 1.51 1.65 0.28 15.41 49.22R30BO004 8.47 1.61 10.24 1.17 1.78 0.30 9.08 32.65R30BO005 6.58 1.40 5.66 0.64 0.00 0.00 7.96 22.24R30BO006 7.81 1.67 10.00 1.14 0.00 0.00 9.45 30.07R30BO007 9.21 1.97 9.40 1.07 0.00 0.00 11.14 32.79R30BO008 42.03 11.66 53.24 6.06 0.00 0.00 54.01 167.00R30BO009 39.51 10.96 53.24 6.06 0.00 0.00 50.77 160.54R30CA003 24.11 6.69 28.91 3.29 0.00 0.00 30.98 93.98R30CA006 36.53 10.13 37.94 4.32 0.00 0.00 46.94 135.86R30CA009 50.59 14.04 56.98 6.48 0.00 0.00 65.01 193.10R30CA010 8.58 1.53 8.43 0.96 0.48 0.08 9.10 29.16R30CA011 9.83 1.76 12.65 1.44 0.67 0.11 10.43 36.89R30CA012 24.56 6.81 26.50 3.02 0.00 0.00 31.55 92.44R30CA013 38.02 10.55 37.94 4.32 0.00 0.00 48.85 139.68R30CA014 16.43 2.95 12.65 1.44 2.09 0.35 17.44 53.35R30RS001 1.24 0.26 3.47 0.39 0.00 0.00 1.50 6.86R30RS002 2.47 0.53 4.82 0.55 0.00 0.00 2.99 11.36R30RS003 6.61 1.20 9.64 1.10 0.60 0.10 7.03 26.28

2 241

EP 1110-1-8, Vol. 130 Nov 09

2-303


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

R30 cont.R30SI002 10.94 2.00 10.96 1.25 1.29 0.22 11.65 38.31R30SI003 13.69 2.48 11.44 1.30 1.29 0.22 14.57 44.99R30SI004 18.39 3.29 13.01 1.48 1.15 0.19 19.53 57.04R30SI005 9.87 2.11 9.03 1.03 0.00 0.00 11.94 33.98

R40R40BO001 7.96 1.53 6.82 1.04 0.00 0.00 10.23 27.58R40BO002 8.90 1.71 6.82 1.04 0.00 0.00 11.44 29.91

R45R45BO004 5.39 1.03 4.50 0.68 0.00 0.00 9.52 21.12R45BO005 6.60 1.26 6.27 0.95 0.00 0.00 11.65 26.73R45BO006 13.68 2.62 14.72 2.24 0.00 0.00 24.17 57.43R45BO007 15.81 3.03 17.86 2.71 0.00 0.00 27.93 67.34R45BO008 16.50 3.16 27.94 4.24 0.00 0.00 29.14 80.98R45CA001 4.66 0.89 4.36 0.66 0.00 0.00 8.23 18.80R45CA002 5.33 1.02 4.36 0.66 0.00 0.00 9.42 20.79R45CA005 12.90 2.47 9.54 1.45 0.00 0.00 22.78 49.14R45CA007 15.75 3.02 14.31 2.17 0.00 0.00 27.81 63.06R45CA010 19.58 3.75 19.76 3.00 0.00 0.00 34.58 80.67R45RS001 1.87 0.36 2.73 0.41 0.00 0.00 3.30 8.67R45SI008 3.62 0.69 4.77 0.72 0.00 0.00 6.39 16.19R45SI009 9.86 1.89 10.63 1.61 0.00 0.00 17.41 41.40R45SI010 13.20 2.53 17.31 2.63 0.00 0.00 23.32 58.99

R50R50BO005 5.72 1.31 4.91 0.75 1.44 0.24 10.02 24.39R50BO006 8.38 1.78 7.37 1.12 0.14 0.02 14.38 33.19

2 242

EP 1110-1-8, Vol. 130 Nov 09

2-304


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

R50 cont.R50BO007 11.48 2.45 7.37 1.12 0.45 0.08 19.73 42.68R50BO008 14.85 3.24 15.23 2.31 1.44 0.24 25.66 62.97R50BO009 21.22 4.58 19.16 2.91 1.44 0.24 36.57 86.12R50BO010 6.29 1.35 4.91 0.75 0.38 0.06 10.83 24.57R50BO011 9.02 1.91 7.37 1.12 0.14 0.02 15.47 35.05R50BO012 12.97 2.77 9.93 1.51 0.45 0.08 22.28 49.99R50BO013 15.96 3.47 12.87 1.95 1.44 0.24 27.56 63.49R50CA001 7.92 1.69 6.88 1.04 0.28 0.05 13.60 31.46R50CA002 9.24 1.97 6.88 1.04 0.28 0.05 15.87 35.33R50CA003 10.64 2.28 9.53 1.45 0.48 0.08 18.30 42.76R50CA004 12.76 2.73 9.83 1.49 0.48 0.08 21.94 49.31R50CA005 11.56 2.47 9.83 1.49 0.48 0.08 19.88 45.79R50CA009 14.38 3.13 14.74 2.24 1.36 0.23 24.84 60.92R50CA010 17.30 3.75 14.74 2.24 1.36 0.23 29.84 69.46R50CA011 17.77 3.85 14.74 2.24 1.36 0.23 30.66 70.85R50CA012 17.32 3.75 14.74 2.24 1.36 0.23 29.87 69.51R50IP001 8.08 1.75 7.86 1.19 0.58 0.10 13.94 33.50R50SI006 6.80 1.47 5.90 0.90 0.55 0.09 11.73 27.44R50SI007 7.30 1.58 5.90 0.90 0.55 0.09 12.58 28.90R50SI013 10.99 2.42 14.54 2.21 1.44 0.24 19.05 50.89R50SI016 11.83 2.60 14.54 2.21 1.44 0.24 20.49 53.35R50SI017 12.85 2.81 14.54 2.21 1.44 0.24 22.23 56.32R50SI022 9.39 2.01 9.83 1.49 0.50 0.08 16.15 39.45R50SI023 10.53 2.25 9.83 1.49 0.50 0.08 18.11 42.79R50SI024 5.19 1.12 2.75 0.42 0.33 0.06 8.95 18.82R50SI025 6.44 1.38 2.95 0.45 0.33 0.06 11.08 22.69R50SI026 12.93 2.75 10.22 1.55 0.33 0.06 22.20 50.04

2 243

EP 1110-1-8, Vol. 130 Nov 09

2-305


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

R55R55AE001 1.05 0.15 1.30 3.45 0.05 0.01 1.23 7.24R55AE002 1.29 0.18 1.30 5.15 0.05 0.01 1.51 9.49R55AE003 1.72 0.25 1.30 6.75 0.10 0.02 2.01 12.15R55AE004 2.22 0.33 1.30 7.15 0.19 0.03 2.61 13.83R55AE008 0.75 0.11 1.30 0.15 0.06 0.01 0.87 3.25R55AE009 0.29 0.04 1.46 0.17 0.00 0.00 0.33 2.29R55AE010 0.52 0.07 2.60 0.30 0.00 0.00 0.61 4.10R55AE011 0.45 0.07 0.81 0.09 0.11 0.02 0.54 2.09R55GL001 0.50 0.07 0.00 0.50 0.03 0.01 0.59 1.70R55GL002 0.98 0.14 0.81 0.59 0.05 0.01 1.15 3.73R55GL003 1.99 0.28 1.46 0.92 0.09 0.02 2.32 7.08R55GL004 2.44 0.34 1.46 1.17 0.04 0.01 2.85 8.31R55GL007 1.81 0.25 2.93 0.33 0.00 0.00 2.10 7.42R55GL008 0.68 0.10 1.79 0.20 0.11 0.02 0.80 3.70R55GL009 0.36 0.05 1.71 0.19 0.00 0.00 0.42 2.73R55GL011 0.88 0.12 2.60 0.30 0.00 0.00 1.02 4.92R55GL012 1.58 0.22 1.46 0.92 0.05 0.01 1.84 6.08R55GL013 0.11 0.03 0.00 0.25 0.09 0.02 0.15 0.65R55GL014 0.46 0.06 0.00 0.35 0.00 0.00 0.53 1.40R55GL015 1.48 0.20 1.46 0.17 0.00 0.00 1.72 5.03R55GL016 0.82 0.11 1.46 0.17 0.00 0.00 0.96 3.52R55GL017 0.29 0.04 0.81 0.09 0.00 0.00 0.34 1.57R55GL018 0.30 0.04 0.81 0.09 0.00 0.00 0.35 1.59R55GL019 0.59 0.08 1.30 0.15 0.00 0.00 0.68 2.80

S10S10CA001 21.52 5.19 17.20 3.27 2.66 0.45 29.79 80.08 26.90 5.30 22.74 4.32 10.75 1.81 41.36 113.18

2 244

EP 1110-1-8, Vol. 130 Nov 09

2-306


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

S10 cont.S10CA002 22.78 8.14 26.04 3.95 12.17 2.04 36.02 111.14 25.75 8.20 34.44 5.23 49.16 8.26 42.86 173.90S10CA003 35.31 12.16 35.87 5.45 9.95 1.67 55.30 155.71 39.91 12.25 47.44 7.20 40.22 6.76 65.79 219.57

S15S15CA001 28.37 10.16 33.55 5.10 9.95 1.67 35.01 123.81 34.04 10.28 42.81 6.50 40.22 6.76 44.67 185.28S15CA002 43.26 15.42 41.37 6.28 13.81 2.32 53.33 175.79 51.91 15.62 52.78 8.02 55.82 9.38 68.06 261.59S15CA003 53.87 19.13 50.56 7.68 15.44 2.59 66.36 215.63 64.64 19.37 64.51 9.80 62.37 10.48 84.68 315.85S15JU001 29.46 10.26 38.79 5.89 2.63 0.44 36.15 123.62 35.36 10.39 49.50 7.52 9.77 1.64 46.13 160.31S15JU002 30.51 10.62 38.79 5.89 2.63 0.44 37.43 126.31 36.61 10.75 49.50 7.52 9.77 1.64 47.76 163.55

S20S20CA001 32.40 11.53 52.78 6.53 12.51 2.10 42.46 160.31 36.00 11.61 68.62 8.48 52.91 8.89 49.95 236.46S20CA002 34.29 12.18 52.78 6.53 12.51 2.10 44.93 165.32 38.11 12.26 68.62 8.48 52.91 8.89 52.85 242.12S20CA003 55.20 19.51 66.58 8.23 17.36 2.92 72.25 242.05 61.34 19.63 86.54 10.70 73.44 12.34 84.98 348.97S20CA004 57.54 20.31 66.58 8.23 17.36 2.92 75.29 248.23 63.94 20.44 86.54 10.70 73.44 12.34 88.56 355.96S20CA005 64.05 23.11 90.35 11.17 33.13 5.57 84.19 311.57 71.17 23.26 117.45 14.52 140.16 23.55 99.03 489.14S20CA006 72.27 25.42 90.35 11.17 19.40 3.26 94.48 316.35 80.30 25.58 117.45 14.52 82.06 13.79 111.14 444.84

S25S25JD001 3.23 0.98 0.00 1.50 1.19 0.20 3.53 10.63 3.88 1.00 0.00 1.50 4.44 0.75 4.53 16.10S25JD002 3.97 1.23 0.00 1.50 1.79 0.30 4.35 13.14 4.77 1.25 0.00 1.50 6.66 1.12 5.59 20.89S25RI001 2.82 0.81 0.00 1.50 0.38 0.06 3.04 8.61 3.39 0.82 0.00 1.50 1.42 0.24 3.91 11.28S25RI002 3.15 0.91 0.00 1.50 0.57 0.10 3.40 9.63 3.78 0.93 0.00 1.50 2.13 0.36 4.37 13.07S25RM001 7.43 2.29 0.00 1.50 3.82 0.64 8.13 23.81 8.92 2.32 0.00 1.50 14.05 2.36 10.44 39.59S25RM002 10.79 3.37 0.00 1.50 6.28 1.06 11.84 34.84 12.94 3.42 0.00 1.50 23.26 3.91 15.22 60.25S25RM003 5.41 1.73 0.00 1.50 3.82 0.64 5.96 19.06 6.49 1.75 0.00 1.50 14.05 2.36 7.66 33.81

S30S30HW001 11.58 5.42 23.08 12.33 1.10 0.18 15.92 69.61 19.31 5.58 27.69 17.89 1.24 0.21 33.18 105.10

2 245

EP 1110-1-8, Vol. 130 Nov 09

2-307


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

S30 cont.S30HW002 15.69 7.32 32.31 17.26 1.35 0.23 21.55 95.71 26.14 7.54 38.77 25.05 1.51 0.25 44.91 144.17S30HW005 6.21 2.91 3.69 1.97 0.66 0.11 5.55 21.10 10.35 3.00 4.43 2.86 0.74 0.12 12.09 33.59S30HW006 10.43 4.85 9.23 4.93 0.71 0.12 9.31 39.58 17.39 4.99 11.08 7.16 0.79 0.13 20.30 61.84S30HW007 11.35 5.27 11.54 6.17 0.71 0.12 10.13 45.29 18.92 5.43 13.85 8.95 0.79 0.13 22.08 70.15S30HW008 11.87 5.50 11.54 6.17 0.71 0.12 10.59 46.50 19.78 5.67 13.85 8.95 0.79 0.13 23.09 72.26S30HW009 12.23 5.71 13.85 7.40 1.05 0.18 10.92 51.34 20.39 5.88 16.61 10.73 1.17 0.20 23.81 78.79S30HW010 14.93 6.96 18.46 9.86 1.16 0.19 13.33 64.89 24.89 7.16 22.15 14.31 1.30 0.22 29.06 99.09S30HW011 14.63 6.82 18.46 9.86 1.21 0.20 13.06 64.24 24.38 7.02 22.15 14.31 1.36 0.23 28.47 97.92S30HW012 17.31 8.06 18.46 9.86 1.35 0.23 15.45 70.72 28.85 8.30 22.15 14.31 1.51 0.25 33.68 109.05S30HW013 13.91 6.48 41.54 22.19 1.08 0.18 19.11 104.49 23.18 6.67 49.84 32.21 1.20 0.20 39.82 153.12S30HW014 11.32 2.25 1.38 0.74 0.42 0.07 12.44 28.62 14.15 2.31 1.66 1.07 0.48 0.08 19.45 39.20S30HW015 12.47 2.48 2.31 1.23 0.42 0.07 13.70 32.68 15.59 2.54 2.77 1.79 0.48 0.08 21.41 44.66S30HW016 11.79 2.34 1.85 0.99 0.42 0.07 12.95 30.41 14.73 2.41 2.22 1.43 0.48 0.08 20.25 41.60S30HW017 12.70 2.52 2.31 1.23 0.42 0.07 13.95 33.20 15.87 2.59 2.77 1.79 0.48 0.08 21.80 45.38S30HW018 14.95 3.00 3.69 1.97 0.80 0.13 16.45 40.99 18.69 3.08 4.43 2.86 0.88 0.15 25.71 55.80S30KB001 3.02 0.63 0.92 0.49 0.37 0.06 2.93 8.42 3.78 0.65 1.11 0.72 0.43 0.07 4.44 11.20S30KB002 3.92 0.82 1.38 0.74 0.47 0.08 3.79 11.20 4.90 0.84 1.66 1.07 0.53 0.09 5.75 14.84S30KB003 3.29 0.67 1.85 0.99 0.26 0.04 3.18 10.28 4.12 0.69 2.22 1.43 0.29 0.05 4.82 13.62S30KB004 4.78 1.02 2.31 1.23 0.81 0.14 4.63 14.92 5.97 1.05 2.77 1.79 0.89 0.15 7.03 19.65S30KB005 3.72 0.79 2.31 1.23 0.53 0.09 3.60 12.27 4.65 0.81 2.77 1.79 0.61 0.10 5.46 16.19S30KB006 5.46 1.16 2.77 1.48 0.85 0.14 5.29 17.15 6.83 1.19 3.32 2.15 0.95 0.16 8.03 22.63S30KB007 3.51 0.73 0.92 0.49 0.37 0.06 3.39 9.47 4.39 0.75 1.11 0.72 0.43 0.07 5.15 12.62S30KB008 4.35 0.90 1.38 0.74 0.41 0.07 4.20 12.05 5.44 0.92 1.66 1.07 0.47 0.08 6.37 16.01S30KB009 5.88 1.24 1.38 0.74 0.81 0.14 5.69 15.88 7.35 1.27 1.66 1.07 0.91 0.15 8.64 21.05S30KB010 3.63 0.76 1.85 0.99 0.49 0.08 3.51 11.31 4.54 0.78 2.22 1.43 0.56 0.09 5.33 14.95S30KB011 5.29 1.09 2.31 1.23 0.54 0.09 5.10 15.65 6.61 1.12 2.77 1.79 0.61 0.10 7.75 20.75S30KB012 6.26 1.32 2.31 1.23 0.88 0.15 6.06 18.21 7.82 1.35 2.77 1.79 0.97 0.16 9.19 24.05

2 246

EP 1110-1-8, Vol. 130 Nov 09

2-308


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

S30 cont.S30KB013 4.23 0.89 2.31 1.23 0.53 0.09 4.09 13.37 5.29 0.91 2.77 1.79 0.61 0.10 6.21 17.68S30KB014 5.73 1.18 2.77 1.48 0.59 0.10 5.53 17.38 7.16 1.21 3.32 2.15 0.67 0.11 8.39 23.01S30KB015 7.67 1.60 3.69 1.97 0.94 0.16 7.42 23.45 9.59 1.64 4.43 2.86 1.04 0.17 11.25 30.98S30KB018 9.06 1.83 2.31 1.23 0.56 0.09 8.73 23.81 11.33 1.88 2.77 1.79 0.64 0.11 13.25 31.77S30KB021 10.52 2.12 3.69 1.97 0.63 0.11 10.13 29.17 13.15 2.18 4.43 2.86 0.72 0.12 15.38 38.84S30KB024 12.07 2.43 5.54 2.96 0.70 0.12 11.63 35.45 15.09 2.49 6.65 4.30 0.80 0.13 17.65 47.11S30KB025 6.41 1.30 1.85 0.99 0.47 0.08 6.18 17.28 8.02 1.34 2.22 1.43 0.53 0.09 9.39 23.02S30KB026 7.65 1.55 1.85 0.99 0.51 0.09 7.38 20.02 9.57 1.59 2.22 1.43 0.57 0.10 11.20 26.68S30KB027 9.72 1.96 2.31 1.23 0.56 0.09 9.36 25.23 12.15 2.01 2.77 1.79 0.64 0.11 14.21 33.68S30KB028 7.31 1.48 2.77 1.48 0.52 0.09 7.04 20.69 9.13 1.52 3.32 2.15 0.58 0.10 10.69 27.49S30KB029 8.83 1.78 2.77 1.48 0.56 0.09 8.51 24.02 11.04 1.83 3.32 2.15 0.64 0.11 12.91 32.00S30KB030 11.13 2.24 3.69 1.97 0.63 0.11 10.72 30.49 13.91 2.30 4.43 2.86 0.72 0.12 16.27 40.61S30KB031 9.56 1.93 4.62 2.47 0.56 0.09 9.21 28.44 11.94 1.98 5.54 3.58 0.64 0.11 13.97 37.76S30KB032 11.28 2.27 4.62 2.47 0.65 0.11 10.86 32.26 14.09 2.33 5.54 3.58 0.72 0.12 16.48 42.86S30KB033 13.02 2.62 5.54 2.96 0.70 0.12 12.54 37.50 16.28 2.68 6.65 4.30 0.80 0.13 19.03 49.87S30KB034 4.63 0.96 1.38 0.74 0.52 0.09 4.47 12.79 5.79 0.99 1.66 1.07 0.58 0.10 6.79 16.98S30KB035 5.27 1.10 1.85 0.99 0.61 0.10 5.09 15.01 6.59 1.12 2.22 1.43 0.69 0.12 7.73 19.90S30KB036 4.96 1.03 1.85 0.99 0.56 0.09 4.79 14.27 6.20 1.06 2.22 1.43 0.64 0.11 7.27 18.93S30KB041 5.66 1.18 1.85 0.99 0.68 0.11 5.47 15.94 7.07 1.21 2.22 1.43 0.76 0.13 8.30 21.12S30KB042 8.09 1.63 2.77 1.48 0.47 0.08 7.79 22.31 10.11 1.67 3.32 2.15 0.53 0.09 11.82 29.69S30KB043 12.07 2.41 1.38 0.74 0.51 0.09 11.61 28.81 15.08 2.47 1.66 1.07 0.57 0.10 17.63 38.58S30KB044 14.89 2.96 1.38 0.74 0.51 0.09 14.32 34.89 18.61 3.03 1.66 1.07 0.57 0.10 21.73 46.77S30KB045 20.05 9.26 35.38 4.71 0.85 0.14 27.51 97.90 33.41 9.54 42.22 6.73 0.95 0.16 57.34 150.35S30KB046 13.93 6.48 25.11 13.41 1.02 0.17 22.96 83.08 23.21 6.67 30.13 19.47 1.14 0.19 51.02 131.83S30KB047 17.46 8.07 29.07 15.53 0.77 0.13 28.76 99.79 29.10 8.31 34.89 22.55 0.85 0.14 63.92 159.76S30KB048 15.28 3.04 7.85 4.19 0.59 0.10 16.80 47.85 19.10 3.12 9.41 6.08 0.66 0.11 26.25 64.73S30KB049 17.26 3.59 8.31 4.44 2.05 0.34 19.06 55.05 21.58 3.68 9.97 6.44 2.31 0.39 29.78 74.15

2 247

EP 1110-1-8, Vol. 130 Nov 09

2-309


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

S30 cont.S30KB050 21.86 4.32 23.08 12.33 0.57 0.10 24.01 86.27 27.33 4.44 27.69 17.89 0.63 0.11 37.53 115.62S30KB051 27.70 5.49 23.08 12.33 0.85 0.14 30.43 100.02 34.62 5.64 27.69 17.89 0.95 0.16 47.56 134.51S30KB052 29.29 5.74 23.08 12.33 0.28 0.05 32.14 102.91 36.61 5.89 27.69 17.89 0.32 0.05 50.23 138.68S30KB053 8.34 1.68 3.69 1.97 0.51 0.09 8.04 24.32 10.43 1.73 4.43 2.86 0.57 0.10 12.20 32.32S30KB054 8.28 1.67 1.38 0.74 0.47 0.08 7.98 20.60 10.36 1.71 1.66 1.07 0.53 0.09 12.11 27.53S30KB055 12.99 6.02 24.08 3.20 0.71 0.12 11.59 58.71 21.65 6.20 28.74 4.58 0.79 0.13 25.26 87.35S30KB056 13.31 6.17 24.08 3.20 0.71 0.12 11.88 59.47 22.19 6.35 28.74 4.58 0.79 0.13 25.90 88.68S30KB057 14.88 6.88 24.08 3.20 0.71 0.12 13.27 63.14 24.80 7.09 28.74 4.58 0.79 0.13 28.94 95.07S30KB058 13.95 6.45 12.00 6.41 0.66 0.11 12.44 52.02 23.24 6.64 14.40 9.31 0.74 0.12 27.12 81.57S30KB059 21.88 10.11 27.69 14.79 0.95 0.16 19.52 95.10 36.47 10.41 33.23 21.47 1.05 0.18 42.55 145.36S30PU001 22.06 4.35 21.13 2.81 0.55 0.09 21.20 72.19 27.58 4.46 25.22 4.02 0.65 0.11 32.18 94.22S30PU002 42.99 8.46 34.39 4.58 0.95 0.16 41.31 132.84 53.74 8.68 41.05 6.55 1.12 0.19 62.70 174.03S30PU003 55.69 10.94 34.39 4.58 1.03 0.17 53.51 160.31 69.61 11.22 41.05 6.55 1.21 0.20 81.21 211.05S30RA002 6.44 1.27 2.46 0.33 0.15 0.03 7.08 17.76 8.05 1.31 2.93 0.47 0.17 0.03 11.06 24.02S30RA003 10.15 2.01 4.82 0.64 0.31 0.05 11.15 29.13 12.69 2.07 5.75 0.92 0.34 0.06 17.43 39.26S30TS001 3.22 0.66 1.11 0.59 0.32 0.05 3.11 9.06 4.02 0.68 1.33 0.86 0.36 0.06 4.71 12.02S30TS002 4.39 0.90 1.57 0.84 0.39 0.07 4.24 12.40 5.49 0.92 1.88 1.21 0.45 0.08 6.43 16.46S30TS003 3.31 0.69 1.57 0.84 0.37 0.06 3.20 10.04 4.14 0.70 1.88 1.21 0.41 0.07 4.86 13.27S30TS004 4.51 0.93 2.03 1.08 0.46 0.08 4.35 13.44 5.64 0.95 2.44 1.58 0.52 0.09 6.61 17.83S30TS005 3.47 0.72 2.03 1.08 0.41 0.07 3.36 11.14 4.34 0.74 2.44 1.58 0.47 0.08 5.09 14.74S30TS006 4.72 0.98 2.49 1.33 0.53 0.09 4.56 14.70 5.90 1.00 2.99 1.93 0.59 0.10 6.92 19.43S30TS007 4.17 0.86 2.95 1.58 0.46 0.08 4.03 14.13 5.22 0.89 3.54 2.29 0.52 0.09 6.12 18.67S30TS008 7.12 1.45 3.88 2.07 0.59 0.10 6.87 22.08 8.90 1.49 4.65 3.01 0.67 0.11 10.43 29.26S30TS009 10.71 4.89 27.69 17.79 0.00 0.00 14.68 75.76 17.84 5.04 33.23 24.47 0.00 0.00 30.59 111.17S30TS010 15.87 7.26 36.92 23.72 0.00 0.00 21.76 105.53 26.45 7.47 44.30 32.63 0.00 0.00 45.35 156.20S30TS011 26.35 12.05 73.84 47.45 0.00 0.00 36.13 195.82 43.91 12.40 88.61 65.26 0.00 0.00 75.29 285.47

2 248

EP 1110-1-8, Vol. 130 Nov 09

2-310


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

S35S35AR001 0.49 0.09 0.00 0.00 0.00 0.00 0.60 1.18S35AR002 0.69 0.13 0.00 0.00 0.00 0.00 0.86 1.68

S40S40BO002 31.30 7.46 38.80 5.16 1.71 0.29 40.83 125.55 39.13 7.62 50.21 6.68 7.03 1.18 57.03 168.88S40BO003 30.64 7.31 38.80 5.16 1.71 0.29 39.97 123.88 38.31 7.46 50.21 6.68 7.03 1.18 55.83 166.70S40BO004 30.06 7.17 38.80 5.16 1.71 0.29 39.22 122.41 37.58 7.33 50.21 6.68 7.03 1.18 54.78 164.79S40CA001 28.58 6.79 33.30 4.43 1.58 0.27 37.26 112.21 35.73 6.94 43.10 5.73 6.06 1.02 52.04 150.62S40CA002 27.14 6.52 33.30 4.43 1.65 0.28 35.45 108.77 33.93 6.66 43.10 5.73 6.28 1.06 49.52 146.28S40CA003 21.53 5.49 37.72 5.02 9.25 1.55 28.48 109.04 26.91 5.60 48.82 6.50 36.45 6.12 39.77 170.17S40CA004 37.46 9.11 58.20 7.74 6.80 1.14 49.07 169.52 46.83 9.31 75.32 10.02 26.48 4.45 68.53 240.94

S45S45DA004 1.63 0.24 0.00 0.25 0.00 0.00 2.52 4.64S45DA005 1.95 0.29 0.00 0.25 0.00 0.00 3.01 5.50S45DA007 2.06 0.31 0.00 0.25 0.00 0.00 3.17 5.79

T10T10CA001 1.08 0.25 0.00 0.08 0.00 0.00 1.33 2.74 1.35 0.26 0.00 0.08 0.00 0.00 1.88 3.57T10CA002 1.61 0.38 0.00 0.08 0.00 0.00 2.00 4.07 2.02 0.39 0.00 0.08 0.00 0.00 2.81 5.30T10CA004 1.19 0.28 0.00 0.08 0.00 0.00 1.48 3.03 1.49 0.29 0.00 0.08 0.00 0.00 2.08 3.94T10CA005 1.61 0.38 0.00 0.08 0.00 0.00 2.00 4.07 2.02 0.39 0.00 0.08 0.00 0.00 2.81 5.30T10CA007 1.80 0.42 0.00 0.08 0.00 0.00 2.23 4.53 2.26 0.43 0.00 0.08 0.00 0.00 3.14 5.91T10CA008 2.41 0.57 0.00 0.08 0.00 0.00 2.99 6.05 3.01 0.58 0.00 0.08 0.00 0.00 4.20 7.87T10CA009 2.20 0.52 0.00 0.08 0.00 0.00 2.73 5.53 2.75 0.53 0.00 0.08 0.00 0.00 3.84 7.20T10CA010 2.41 0.56 0.00 0.08 0.00 0.00 2.99 6.04 3.01 0.58 0.00 0.08 0.00 0.00 4.20 7.87T10CA011 3.36 0.79 0.00 0.08 0.00 0.00 4.16 8.39 4.20 0.80 0.00 0.08 0.00 0.00 5.85 10.93T10CA012 3.24 0.76 0.00 0.08 0.00 0.00 4.02 8.10 4.06 0.78 0.00 0.08 0.00 0.00 5.65 10.57

2 249

EP 1110-1-8, Vol. 130 Nov 09

2-311


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

T10 cont.T10CA013 3.56 0.84 0.00 0.08 0.00 0.00 4.41 8.89 4.45 0.85 0.00 0.08 0.00 0.00 6.21 11.59T10CA014 2.96 0.70 0.00 0.08 0.00 0.00 3.67 7.41 3.71 0.71 0.00 0.08 0.00 0.00 5.17 9.67T10CA015 4.41 1.03 0.00 0.10 0.00 0.00 5.47 11.01 5.52 1.06 0.00 0.10 0.00 0.00 7.69 14.37T10CA016 4.32 1.01 0.00 0.12 0.00 0.00 5.35 10.80 5.40 1.03 0.00 0.12 0.00 0.00 7.53 14.08T10CA017 4.69 1.10 0.00 0.13 0.00 0.00 5.81 11.73 5.86 1.12 0.00 0.13 0.00 0.00 8.17 15.28T10CA018 4.15 0.97 0.00 0.13 0.00 0.00 5.14 10.39 5.19 0.99 0.00 0.13 0.00 0.00 7.23 13.54T10CA019 0.12 0.03 0.00 0.05 0.00 0.00 0.15 0.35 0.15 0.03 0.00 0.05 0.00 0.00 0.21 0.44T10CA020 4.40 1.03 0.00 0.15 0.00 0.00 5.45 11.03 5.50 1.05 0.00 0.15 0.00 0.00 7.66 14.36T10CA021 5.87 1.38 0.00 0.19 0.00 0.00 7.27 14.71 7.34 1.41 0.00 0.19 0.00 0.00 10.23 19.17T10CA022 6.37 1.49 0.00 0.19 0.00 0.00 7.89 15.94 7.96 1.52 0.00 0.19 0.00 0.00 11.09 20.76T10CA023 5.92 1.39 0.00 0.20 0.00 0.00 7.33 14.84 7.39 1.42 0.00 0.20 0.00 0.00 10.31 19.32T10CA024 8.75 2.05 0.00 0.28 0.00 0.00 10.84 21.92 10.94 2.10 0.00 0.28 0.00 0.00 15.25 28.57T10CA025 9.32 2.18 0.00 0.29 0.00 0.00 11.54 23.33 11.65 2.23 0.00 0.29 0.00 0.00 16.23 30.40T10CA026 12.70 2.98 0.00 0.40 0.00 0.00 15.73 31.81 15.88 3.04 0.00 0.40 0.00 0.00 22.13 41.45T10CA027 13.69 3.21 0.00 0.42 0.00 0.00 16.96 34.28 17.11 3.28 0.00 0.42 0.00 0.00 23.85 44.66T10JD001 1.02 0.25 0.00 0.25 0.09 0.02 1.28 2.91 1.28 0.26 0.00 0.25 0.10 0.02 1.80 3.71

T15T15CA002 6.56 1.88 7.54 1.29 0.00 0.00 12.78 30.05 8.21 1.91 9.76 1.67 0.00 0.00 18.15 39.70T15CA005 8.11 2.32 8.62 1.48 0.00 0.00 15.79 36.32 10.14 2.36 11.16 1.91 0.00 0.00 22.42 47.99T15CA008 16.17 4.62 15.63 2.68 0.00 0.00 31.48 70.58 20.21 4.70 20.22 3.46 0.00 0.00 44.70 93.29T15CA009 23.14 6.62 17.78 3.05 0.00 0.00 45.05 95.64 28.92 6.73 23.01 3.94 0.00 0.00 63.95 126.55T15CA011 22.53 6.44 19.94 3.42 0.00 0.00 43.88 96.21 28.17 6.55 25.80 4.42 0.00 0.00 62.29 127.23T15CA012 23.00 7.32 25.87 3.45 0.00 0.00 45.57 105.21 27.38 7.41 33.48 4.46 0.00 0.00 56.51 129.24T15CA014 27.27 8.68 25.87 3.45 0.00 0.00 54.04 119.31 32.47 8.79 33.48 4.46 0.00 0.00 67.02 146.22T15CA016 30.35 9.66 33.41 4.45 0.00 0.00 60.14 138.01 36.13 9.78 43.24 5.76 0.00 0.00 74.58 169.49T15CA017 40.34 12.84 44.19 5.89 0.00 0.00 79.92 183.18 48.02 12.99 57.19 7.62 0.00 0.00 99.12 224.94T15CA018 50.93 17.42 53.32 3.94 0.00 0.00 94.60 220.21 61.11 17.63 68.03 5.03 0.00 0.00 127.73 279.53

2 250

EP 1110-1-8, Vol. 130 Nov 09

2-312


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

T15 cont.T15CA019 79.05 27.03 78.14 5.78 0.00 0.00 146.83 336.83 94.86 27.37 99.70 7.37 0.00 0.00 198.25 427.55T15CA020 8.28 2.37 8.62 1.48 0.00 0.00 16.12 36.87 10.35 2.41 11.16 1.91 0.00 0.00 22.88 48.71T15CA021 8.57 2.45 9.70 1.66 0.00 0.00 16.68 39.06 10.71 2.49 12.55 2.15 0.00 0.00 23.69 51.59T15CA022 9.07 2.59 9.70 1.66 0.00 0.00 17.66 40.68 11.34 2.64 12.55 2.15 0.00 0.00 25.08 53.76T15CA023 23.14 6.62 17.78 3.05 0.00 0.00 45.05 95.64 28.92 6.73 23.01 3.94 0.00 0.00 63.95 126.55T15CA024 11.59 3.31 11.86 2.03 0.00 0.00 22.57 51.36 14.49 3.37 15.34 2.63 0.00 0.00 32.04 67.87T15CS004 7.39 2.11 7.22 1.24 0.00 0.00 14.38 32.34 9.23 2.15 9.35 1.60 0.00 0.00 20.42 42.75T15CS007 12.89 3.69 12.83 2.20 0.00 0.00 25.10 56.71 16.11 3.75 16.60 2.84 0.00 0.00 35.63 74.93T15JD005 5.91 1.69 7.54 1.29 0.00 0.00 11.50 27.93 7.39 1.72 9.76 1.67 0.00 0.00 16.33 36.87T15JD006 7.03 2.01 7.98 1.37 0.00 0.00 13.68 32.07 8.78 2.04 10.32 1.77 0.00 0.00 19.42 42.33T15JD007 8.07 2.31 9.70 1.66 0.00 0.00 15.72 37.46 10.09 2.35 12.55 2.15 0.00 0.00 22.32 49.46T15JD008 14.25 4.08 15.09 2.59 0.00 0.00 27.75 63.76 17.82 4.15 19.53 3.35 0.00 0.00 39.40 84.25T15JD009 15.00 4.29 15.09 2.59 0.00 0.00 29.20 66.17 18.75 4.36 19.53 3.35 0.00 0.00 41.46 87.45T15JD010 18.58 5.31 19.94 3.42 0.00 0.00 36.19 83.44 23.23 5.41 25.80 4.42 0.00 0.00 51.37 110.23T15JD011 20.12 5.75 19.94 3.42 0.00 0.00 39.17 88.40 25.15 5.85 25.80 4.42 0.00 0.00 55.61 116.83T15KM008 34.68 11.04 33.41 4.45 0.00 0.00 68.72 152.30 41.29 11.17 43.24 5.76 0.00 0.00 85.22 186.68

T20T20CA001 20.62 6.15 22.06 2.94 3.39 0.57 18.77 74.50 22.21 6.18 28.15 3.75 14.26 2.40 21.90 98.85T20CA002 29.22 8.94 31.16 4.15 10.18 1.71 26.71 112.07 31.47 8.99 39.76 5.30 42.75 7.18 31.15 166.60T20CA003 42.89 13.48 44.22 5.89 14.71 2.47 39.37 163.03 46.19 13.54 56.42 7.52 61.80 10.38 45.92 241.77

T25T25CA006 17.12 3.66 26.24 3.50 0.00 0.00 22.00 72.52T25CA007 18.79 4.01 28.69 3.82 0.00 0.00 24.14 79.45T25CA008 20.35 4.35 34.69 4.62 0.00 0.00 26.15 90.16T25JD008 8.55 1.55 10.81 1.44 0.63 0.11 9.10 32.19T25JD009 10.47 1.88 17.20 2.29 0.63 0.11 11.13 43.71

2 251

EP 1110-1-8, Vol. 130 Nov 09

2-313


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

T25 cont.T25JD010 11.62 2.15 22.11 2.95 1.38 0.23 12.40 52.84T25JD012 16.24 3.20 31.94 4.26 3.89 0.65 17.51 77.69T25JD013 20.91 4.02 41.76 5.57 3.89 0.65 22.45 99.25T25JD014 15.77 2.88 27.02 3.60 1.38 0.23 16.79 67.67T25JD015 1.72 0.33 4.42 0.59 0.36 0.06 1.85 9.33T25JD016 2.57 0.48 5.50 0.73 0.36 0.06 2.75 12.45T25JD017 2.99 0.55 5.50 0.73 0.36 0.06 3.19 13.38T25JD018 3.74 0.68 6.58 0.88 0.36 0.06 3.98 16.28T25JD019 3.94 0.73 7.96 1.06 0.48 0.08 4.21 18.46T25JD020 3.84 0.79 8.94 1.19 1.43 0.24 4.17 20.60

T30T30DW005 3.44 0.68 4.32 0.57 0.23 0.04 5.00 14.28 4.59 0.71 5.72 0.76 0.87 0.15 7.42 20.22T30DW011 20.21 3.87 18.18 2.42 0.00 0.00 29.21 73.89 26.95 4.01 24.04 3.20 0.00 0.00 43.29 101.49T30DW012 0.88 0.17 2.31 0.31 0.06 0.01 1.28 5.02 1.17 0.18 3.01 0.40 0.20 0.03 1.89 6.88T30DW013 1.22 0.25 3.20 0.43 0.12 0.02 1.78 7.02 1.62 0.25 4.17 0.56 0.42 0.07 2.63 9.72T30DW014 3.14 0.64 3.44 0.46 0.41 0.07 4.60 12.76 4.18 0.66 4.55 0.61 1.53 0.26 6.81 18.60T30DW016 5.67 1.11 5.60 0.75 0.23 0.04 8.23 21.63 7.56 1.15 7.41 0.99 0.87 0.15 12.20 30.33T30DW017 7.06 1.39 6.88 0.92 0.41 0.07 10.26 26.99 9.41 1.44 9.10 1.21 1.53 0.26 15.20 38.15T30DW018 7.93 1.56 7.67 1.02 0.41 0.07 11.52 30.18 10.57 1.61 10.14 1.35 1.53 0.26 17.07 42.53T30TM001 30.57 5.86 18.18 2.42 0.00 0.00 44.18 101.21 40.76 6.06 24.04 3.20 0.00 0.00 65.47 139.53T30TM004 33.01 6.32 18.18 2.42 0.00 0.00 47.70 107.63 44.02 6.54 24.04 3.20 0.00 0.00 70.70 148.50T30TM007 43.59 8.35 21.62 2.88 0.00 0.00 62.99 139.43 58.12 8.64 28.59 3.81 0.00 0.00 93.35 192.51T30TM008 43.88 8.41 21.62 2.88 0.00 0.00 63.40 140.19 58.50 8.69 28.59 3.81 0.00 0.00 93.97 193.56T30TM009 42.90 8.22 26.53 3.53 0.00 0.00 61.99 143.17 57.20 8.50 35.09 4.68 0.00 0.00 91.87 197.34T30TM012 74.84 14.34 37.83 5.03 0.00 0.00 108.14 240.18 99.78 14.83 50.04 6.67 0.00 0.00 160.27 331.59T30TM013 122.69 23.50 51.59 6.86 0.00 0.00 177.28 381.92 163.58 24.31 68.23 9.09 0.00 0.00 262.76 527.97T30TM014 117.47 22.50 51.59 6.86 0.00 0.00 169.75 368.17 156.63 23.28 68.23 9.09 0.00 0.00 251.59 508.82

2 252

EP 1110-1-8, Vol. 130 Nov 09

2-314


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

T30 cont.T30TM015 125.25 23.99 51.59 6.86 0.00 0.00 180.99 388.68 167.00 24.82 68.23 9.09 0.00 0.00 268.25 537.39T30VE007 17.03 3.26 12.28 1.63 0.00 0.00 24.60 58.80 22.70 3.37 16.25 2.17 0.00 0.00 36.47 80.96T30VE008 21.64 4.14 18.18 2.42 0.00 0.00 31.26 77.64 28.85 4.29 24.04 3.20 0.00 0.00 46.34 106.72T30VE009 35.05 6.71 24.57 3.27 0.00 0.00 50.65 120.25 46.73 6.95 32.49 4.33 0.00 0.00 75.07 165.57T30VE010 42.45 8.13 27.02 3.60 0.00 0.00 61.34 142.54 56.60 8.41 35.74 4.76 0.00 0.00 90.92 196.43

T35T35CT001 22.97 4.40 13.76 1.83 0.00 0.00 33.19 76.15 30.63 4.55 18.20 2.42 0.00 0.00 49.19 104.99T35CT002 28.29 5.42 13.76 1.83 0.00 0.00 40.88 90.18 37.72 5.61 18.20 2.42 0.00 0.00 60.59 124.54T35CT003 31.78 6.09 18.18 2.42 0.00 0.00 45.92 104.39 42.37 6.30 24.04 3.20 0.00 0.00 68.06 143.97T35CT004 29.94 5.73 10.02 1.33 0.00 0.00 43.26 90.28 39.91 5.93 13.26 1.76 0.00 0.00 64.11 124.97T35CT005 28.32 5.42 10.02 1.33 0.00 0.00 40.92 86.01 37.75 5.61 13.26 1.76 0.00 0.00 60.64 119.02T35CT006 28.32 5.42 10.02 1.33 0.00 0.00 40.92 86.01 37.75 5.61 13.26 1.76 0.00 0.00 60.64 119.02T35CT007 31.34 6.00 10.02 1.33 0.00 0.00 45.28 93.97 41.78 6.21 13.26 1.76 0.00 0.00 67.11 130.12T35CT008 40.14 7.69 14.74 1.96 0.00 0.00 58.00 122.53 53.52 7.95 19.50 2.59 0.00 0.00 85.96 169.52T35CT009 46.71 8.95 14.74 1.96 0.00 0.00 67.50 139.86 62.28 9.26 19.50 2.59 0.00 0.00 100.04 193.67T35CT010 45.76 8.77 14.74 1.96 0.00 0.00 66.12 137.35 61.01 9.07 19.50 2.59 0.00 0.00 98.00 190.17T35CT011 54.91 10.52 17.20 2.29 0.00 0.00 79.34 164.26 73.21 10.88 22.74 3.03 0.00 0.00 117.59 227.45

T40T40AG001 8.25 1.62 7.86 1.19 0.39 0.07 8.96 28.34T40AH001 2.64 0.51 0.00 0.25 0.00 0.00 3.25 6.65T40AH003 3.91 0.75 0.00 0.25 0.00 0.00 4.82 9.73T40AH004 4.84 0.93 0.00 0.25 0.00 0.00 5.97 11.99T40GN001 1.74 0.28 0.00 0.00 0.00 0.00 1.67 3.69 2.14 0.29 0.00 0.00 0.00 0.00 2.35 4.78T40KF011 0.27 0.05 0.00 0.00 0.00 0.00 0.25 0.57T40KF013 0.40 0.08 0.00 0.00 0.00 0.00 0.37 0.85T40KF014 0.36 0.07 0.00 0.00 0.00 0.00 0.33 0.76

2 253

EP 1110-1-8, Vol. 130 Nov 09

2-315


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

T40 cont.T40KF016 0.51 0.10 0.00 0.00 0.00 0.00 0.47 1.08T40KF018 0.62 0.12 0.00 0.00 0.00 0.00 0.57 1.31T40KF020 0.72 0.14 0.00 0.00 0.00 0.00 0.66 1.52T40KF021 0.29 0.06 0.00 0.10 0.00 0.00 0.32 0.77T40KF022 0.58 0.11 0.00 0.10 0.00 0.00 0.63 1.42T40KF023 0.39 0.08 0.00 0.05 0.00 0.00 0.42 0.94T40KF024 0.46 0.09 0.00 0.05 0.00 0.00 0.50 1.10T40MY002 0.58 0.09 0.00 0.00 0.00 0.00 0.56 1.23 0.71 0.09 0.00 0.00 0.00 0.00 0.78 1.58T40MY003 0.72 0.11 0.00 0.00 0.00 0.00 0.69 1.52 0.88 0.12 0.00 0.00 0.00 0.00 0.97 1.97T40MY004 0.83 0.13 0.00 0.00 0.00 0.00 0.80 1.76 1.02 0.14 0.00 0.00 0.00 0.00 1.12 2.28T40MY005 1.17 0.19 0.00 0.00 0.00 0.00 1.12 2.48 1.44 0.19 0.00 0.00 0.00 0.00 1.58 3.21T40MY006 1.33 0.21 0.00 0.00 0.00 0.00 1.28 2.82 1.64 0.22 0.00 0.00 0.00 0.00 1.80 3.66T40PA001 0.78 0.15 0.00 0.24 0.00 0.00 0.97 2.14T40PA002 4.31 0.83 0.00 0.24 0.00 0.00 5.32 10.70T40PA003 5.36 1.03 0.00 0.26 0.00 0.00 6.61 13.26T40PA004 6.26 1.20 0.00 0.26 0.00 0.00 7.72 15.44T40PA005 11.97 2.29 0.00 0.27 0.00 0.00 14.77 29.30T40PA006 12.27 2.35 0.00 0.27 0.00 0.00 15.14 30.03T40RS001 2.70 0.57 0.00 0.00 0.00 0.00 2.67 5.94T40RS002 2.79 0.59 0.00 0.00 0.00 0.00 2.76 6.14T40RS003 3.00 0.63 0.00 0.00 0.00 0.00 2.96 6.59T40XX034 15.52 2.71 27.03 4.11 0.00 0.00 15.77 65.14T40XX035 15.76 2.75 28.75 4.37 0.00 0.00 16.02 67.65T40XX036 18.91 3.30 32.78 4.98 0.00 0.00 19.22 79.19T40XX037 18.56 3.24 32.78 4.98 0.00 0.00 18.86 78.42T40XX038 19.42 3.39 32.78 4.98 0.00 0.00 19.74 80.31

2 254

EP 1110-1-8, Vol. 130 Nov 09

2-316


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

T45T45EA006 3.35 0.76 0.00 0.50 1.40 0.24 2.33 8.58T45EA007 4.97 1.12 0.00 0.50 2.11 0.35 3.46 12.51T45MY004 2.41 0.54 0.00 0.30 1.00 0.17 2.35 6.77 3.01 0.56 0.00 0.30 3.67 0.62 3.35 11.51T45MY005 3.19 0.73 0.00 0.30 1.51 0.25 3.11 9.09 3.98 0.75 0.00 0.30 5.50 0.92 4.45 15.90T45MY006 3.29 0.75 0.00 0.30 1.51 0.25 3.21 9.31 4.11 0.77 0.00 0.30 5.50 0.92 4.59 16.19T45MY007 3.17 0.73 0.00 0.30 1.51 0.25 3.10 9.06 3.96 0.75 0.00 0.30 5.50 0.92 4.43 15.86T45MY015 2.60 0.58 0.00 0.40 1.00 0.17 2.35 7.10 3.24 0.59 0.00 0.40 3.67 0.62 3.39 11.91T45MY016 2.65 0.59 0.00 0.40 1.00 0.17 2.40 7.21 3.32 0.61 0.00 0.40 3.67 0.62 3.46 12.08T45MY017 2.80 0.66 0.00 0.40 1.51 0.25 2.54 8.16 3.50 0.67 0.00 0.40 5.50 0.92 3.67 14.66T45MY018 2.03 0.40 0.00 0.40 1.00 0.17 1.71 5.71T45MY019 2.01 0.40 0.00 0.40 1.00 0.17 1.69 5.67T45XX001 3.13 0.67 0.00 0.40 0.81 0.14 3.03 8.18 3.91 0.69 0.00 0.40 2.94 0.49 4.33 12.76T45XX003 4.29 0.89 0.00 0.40 0.81 0.14 4.15 10.68 5.36 0.92 0.00 0.40 2.94 0.49 5.92 16.03T45XX008 2.58 0.56 0.00 0.40 0.81 0.14 2.33 6.82 3.23 0.58 0.00 0.40 2.94 0.49 3.36 11.00T45XX009 3.28 0.59 0.00 0.40 0.81 0.14 2.73 7.95T45XX010 3.30 0.59 0.00 0.40 0.81 0.14 2.74 7.98T45XX011 2.63 0.57 0.00 0.40 0.72 0.12 1.82 6.26T45XX012 2.81 0.60 0.00 0.40 0.72 0.12 1.95 6.60T45XX013 2.93 0.63 0.00 0.40 0.81 0.14 2.03 6.94T45XX014 3.54 0.77 0.00 0.50 1.08 0.18 2.46 8.53T45XX015 3.64 0.79 0.00 0.50 1.08 0.18 2.52 8.71T45XX016 4.07 0.88 0.00 0.50 1.21 0.20 2.82 9.68T45XX017 4.28 0.94 0.00 0.50 1.41 0.24 2.97 10.34T45XX018 4.33 0.95 0.00 0.50 1.41 0.24 3.01 10.44T45XX019 5.02 1.08 0.00 0.50 1.41 0.24 3.48 11.73T45XX020 4.80 1.05 0.00 0.60 1.61 0.27 3.33 11.66T45XX021 5.27 1.14 0.00 0.60 1.61 0.27 3.65 12.54

2 255

EP 1110-1-8, Vol. 130 Nov 09

2-317


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

T45 cont.T45XX022 5.91 1.29 0.00 0.60 1.88 0.32 4.10 14.10T45XX023 7.04 1.54 0.00 0.60 2.29 0.38 4.89 16.74T45XX024 2.24 0.49 0.00 0.09 0.81 0.14 1.55 5.32T45XX025 2.45 0.54 0.00 0.10 0.81 0.14 1.70 5.74T45XX026 1.39 0.30 0.00 0.40 0.44 0.07 0.97 3.57T45XX027 1.54 0.34 0.00 0.40 0.58 0.10 1.07 4.03T45XX028 1.74 0.39 0.00 0.40 0.75 0.13 1.21 4.62T45XX029 5.83 1.55 6.19 0.70 0.40 0.07 5.80 20.54T45XX030 5.68 1.55 6.19 0.70 0.81 0.14 5.69 20.76T45XX031 6.95 1.88 6.19 0.70 0.81 0.14 6.94 23.61T45XX032 4.32 0.74 0.00 0.50 0.60 0.10 3.58 9.84T45XX033 5.04 0.87 0.00 0.60 0.81 0.14 4.18 11.64T45XX034 2.40 0.53 0.00 0.40 0.81 0.14 1.67 5.95T45XX035 2.57 0.56 0.00 0.40 0.81 0.14 1.78 6.26

T50T50GM001 1.54 0.31 5.06 0.67 0.19 0.03 1.68 9.48 1.89 0.32 6.50 0.86 0.62 0.10 2.22 12.51T50GM004 3.51 0.69 12.01 1.60 0.19 0.03 3.82 21.85 4.32 0.70 15.44 2.05 0.62 0.10 5.04 28.27T50GM005 3.78 0.74 12.01 1.60 0.20 0.03 4.11 22.47 4.65 0.75 15.44 2.05 0.69 0.12 5.42 29.12T50XX001 1.46 0.30 5.48 0.73 0.27 0.05 1.61 9.90 1.80 0.31 7.04 0.94 0.90 0.15 2.12 13.26T50XX002 1.79 0.36 5.48 0.73 0.21 0.04 1.96 10.57 2.20 0.37 7.04 0.94 0.70 0.12 2.58 13.95T50XX003 2.04 0.41 7.59 1.01 0.21 0.04 2.24 13.54 2.52 0.42 9.75 1.30 0.68 0.11 2.95 17.73T50XX004 1.77 0.36 5.48 0.73 0.29 0.05 1.95 10.63 2.18 0.37 7.04 0.94 1.01 0.17 2.57 14.28T50XX005 2.12 0.42 5.48 0.73 0.22 0.04 2.32 11.33 2.61 0.43 7.04 0.94 0.77 0.13 3.06 14.98T50XX006 2.20 0.44 7.59 1.01 0.21 0.04 2.40 13.89 2.70 0.45 9.75 1.30 0.75 0.13 3.16 18.24T50XX007 1.55 0.32 5.48 0.73 0.27 0.05 1.70 10.10 1.91 0.32 7.04 0.94 0.90 0.15 2.24 13.50T50XX008 1.90 0.38 5.48 0.73 0.21 0.04 2.08 10.82 2.34 0.39 7.04 0.94 0.70 0.12 2.75 14.28T50XX009 2.35 0.47 7.59 1.01 0.21 0.04 2.57 14.24 2.89 0.48 9.75 1.30 0.68 0.11 3.39 18.60

2 256

EP 1110-1-8, Vol. 130 Nov 09

2-318


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

T50 cont.T50XX010 2.12 0.43 5.48 0.73 0.29 0.05 2.33 11.43 2.61 0.44 7.04 0.94 1.01 0.17 3.07 15.28T50XX011 2.31 0.46 7.59 1.01 0.22 0.04 2.53 14.16 2.85 0.47 9.75 1.30 0.77 0.13 3.33 18.60T50XX012 2.42 0.48 7.59 1.01 0.21 0.04 2.65 14.40 2.98 0.49 9.75 1.30 0.75 0.13 3.49 18.89T50XX013 1.92 0.39 1.95 0.22 0.27 0.05 2.10 6.90 2.36 0.40 2.78 0.32 0.90 0.15 2.77 9.68T50XX014 2.16 0.43 1.95 0.22 0.21 0.04 2.36 7.37 2.66 0.44 2.78 0.32 0.70 0.12 3.11 10.13T50XX015 2.50 0.49 3.38 0.38 0.21 0.04 2.73 9.73 3.08 0.51 4.82 0.55 0.68 0.11 3.60 13.35T50XX016 2.30 0.46 3.38 0.38 0.29 0.05 2.52 9.38 2.83 0.47 4.82 0.55 1.01 0.17 3.32 13.17T50XX017 2.35 0.47 3.38 0.38 0.22 0.04 2.56 9.40 2.89 0.48 4.82 0.55 0.77 0.13 3.38 13.02T50XX018 2.82 0.56 3.38 0.38 0.21 0.04 3.08 10.47 3.48 0.57 4.82 0.55 0.75 0.13 4.06 14.36T50XX019 2.24 0.45 3.38 0.38 0.21 0.04 2.45 9.15 2.76 0.46 4.82 0.55 0.70 0.12 3.23 12.64T50XX020 2.73 0.54 3.38 0.38 0.22 0.04 2.98 10.27 3.36 0.55 4.82 0.55 0.77 0.13 3.93 14.11T50XX021 2.47 0.49 3.38 0.38 0.21 0.04 2.70 9.67 3.04 0.50 4.82 0.55 0.68 0.11 3.56 13.26T50XX022 3.93 0.95 11.35 1.40 0.38 0.06 3.98 22.05 4.91 0.97 14.69 1.82 1.49 0.25 5.36 29.49T50XX023 3.06 0.75 20.23 2.88 0.38 0.06 3.12 30.48 3.83 0.77 25.92 3.69 1.49 0.25 4.19 40.14T50XX024 2.65 0.65 20.23 2.88 0.38 0.06 2.70 29.55 3.32 0.67 25.92 3.69 1.49 0.25 3.63 38.97T50XX025 5.13 1.25 10.72 1.33 0.62 0.10 5.22 24.37 6.42 1.28 13.88 1.72 2.54 0.43 7.02 33.29T50XX026 5.23 1.27 13.24 1.64 0.59 0.10 5.31 27.38 6.53 1.30 17.14 2.12 2.29 0.38 7.14 36.90T50XX027 7.01 1.99 23.60 3.14 0.55 0.09 7.09 43.47 8.41 2.02 30.48 4.06 2.10 0.35 9.82 57.24T50XX028 6.94 2.00 20.48 2.73 0.83 0.14 7.04 40.16 8.32 2.03 26.45 3.52 3.23 0.54 9.75 53.84T50XX029 6.38 1.84 27.60 3.67 0.83 0.14 6.48 46.94 7.65 1.87 35.65 4.74 3.23 0.54 8.97 62.65T50XX030 8.20 2.35 31.16 4.15 0.83 0.14 8.31 55.14 9.84 2.38 40.25 5.36 3.23 0.54 11.51 73.11T50XX031 7.56 2.16 35.62 4.74 0.76 0.13 7.66 58.63 9.07 2.19 46.00 6.12 2.91 0.49 10.61 77.39T50XX032 7.62 2.16 23.60 3.14 0.55 0.09 7.72 44.88 9.15 2.19 30.48 4.06 2.10 0.35 10.68 59.01T50XX033 8.27 2.36 35.62 4.74 0.76 0.13 8.38 60.26 9.92 2.39 46.00 6.12 2.91 0.49 11.60 79.43T50XX035 7.33 1.77 13.24 1.64 0.59 0.10 7.43 32.10 9.16 1.81 17.14 2.12 2.29 0.38 10.00 42.90

T55T55CA002 34.99 15.03 35.03 5.65 9.52 1.60 45.40 147.22 38.88 15.10 45.33 7.31 37.45 6.29 53.21 203.57

2 257

EP 1110-1-8, Vol. 130 Nov 09

2-319


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

T55 cont.T55CA003 47.45 20.78 50.55 8.15 17.82 2.99 61.76 209.50 52.72 20.88 65.42 10.55 70.09 11.78 72.38 303.82T55CA007 26.32 11.17 26.24 4.23 9.88 1.66 34.08 113.58 29.24 11.23 33.96 5.48 38.89 6.53 39.95 165.28T55CA008 25.25 7.22 19.78 1.77 7.79 1.31 29.11 92.23 26.79 7.26 23.90 2.14 30.12 5.06 32.83 128.10T55CA009 29.64 8.56 21.68 1.94 10.77 1.81 34.22 108.62 31.45 8.60 26.20 2.35 41.64 7.00 38.59 155.83T55CA010 25.81 7.20 16.28 1.46 4.14 0.70 29.64 85.23 27.39 7.23 19.67 1.76 16.29 2.74 33.42 108.50T55CA011 30.35 8.51 19.78 1.77 5.82 0.98 34.88 102.09 32.21 8.55 23.90 2.14 22.90 3.85 39.34 132.89T55CA012 36.50 10.46 27.01 2.42 11.95 2.01 42.09 132.44 38.74 10.51 32.64 2.92 47.02 7.90 47.47 187.20T55CA013 39.88 11.52 30.81 2.76 15.14 2.54 46.04 148.69 42.32 11.58 37.23 3.34 59.94 10.07 51.93 216.41T55JD001 19.77 5.64 20.16 1.81 5.82 0.98 22.78 76.96 20.98 5.66 24.36 2.18 22.90 3.85 25.69 105.62T55JD002 22.92 6.49 21.68 1.94 5.82 0.98 26.38 86.21 24.33 6.52 26.20 2.35 22.90 3.85 29.76 115.91T55JD003 28.70 8.39 28.91 2.59 12.94 2.17 33.20 116.90 30.46 8.43 34.93 3.13 50.88 8.55 37.44 173.82T55JD004 32.05 9.42 31.42 2.82 15.45 2.60 37.10 130.86 34.01 9.46 37.97 3.40 60.80 10.21 41.85 197.70T55KM009 26.40 11.20 26.30 4.24 9.88 1.66 34.18 113.86 29.33 11.26 34.03 5.49 38.89 6.53 40.07 165.60T55KM012 36.89 16.47 56.15 9.06 17.82 2.99 48.17 187.55 40.99 16.56 72.67 11.72 70.09 11.78 56.45 280.26T55KM013 87.99 38.14 80.08 12.92 28.22 4.74 114.32 366.41 97.76 38.33 103.63 16.71 110.97 18.64 133.99 520.03T55KM014 99.06 45.07 107.78 17.38 58.27 9.79 129.72 467.07 110.06 45.30 139.48 22.50 229.20 38.51 152.04 737.09T55KM015 35.49 10.23 29.60 2.65 12.94 2.17 40.96 134.04 37.66 10.28 35.76 3.20 50.88 8.55 46.20 192.53T55KM016 40.43 11.69 32.71 2.93 15.45 2.60 46.68 152.49 42.90 11.75 39.53 3.54 60.80 10.21 52.65 221.38T55VO002 21.38 6.15 22.75 2.04 7.64 1.28 24.66 85.90 22.68 6.18 27.49 2.46 30.24 5.08 27.82 121.95T55VO003 22.88 6.50 22.75 2.04 6.22 1.04 26.35 87.78 24.28 6.53 27.49 2.46 24.47 4.11 29.71 119.05T55VO004 32.17 9.29 31.50 2.82 11.95 2.01 37.14 126.88 34.14 9.33 38.06 3.41 47.02 7.90 41.89 181.75T55VO005 27.13 7.56 25.56 2.29 3.61 0.61 31.15 97.91 28.79 7.59 30.89 2.77 14.20 2.39 35.13 121.76T55VO006 35.66 10.45 35.30 3.16 16.53 2.78 41.26 145.14 37.84 10.50 42.66 3.82 65.00 10.92 46.53 217.27

T56T56CA006 53.16 23.10 56.50 9.11 19.57 3.29 69.10 233.83 59.07 23.22 92.18 14.00 76.39 12.83 80.99 358.68

2 258

EP 1110-1-8, Vol. 130 Nov 09

2-320


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

T57T57CU001 7.84 1.85 7.47 0.99 0.37 0.06 9.69 28.27T57CU002 10.87 2.56 7.47 0.99 0.37 0.06 13.42 35.74T57CU003 11.55 2.72 11.30 1.50 0.37 0.06 14.26 41.76T57CU004 12.40 2.92 17.39 2.31 0.37 0.06 15.32 50.77T57CU005 14.08 3.31 32.92 4.38 0.37 0.06 17.39 72.51

T60T60KI001 16.95 4.87 17.20 2.61 2.81 0.47 18.16 63.07 20.34 4.94 22.74 3.45 10.69 1.80 24.89 88.85T60KI002 25.44 7.55 32.43 4.93 8.97 1.51 27.44 108.27 30.53 7.66 42.89 6.51 34.64 5.82 37.61 165.66T60KI003 42.15 12.19 44.22 6.72 9.14 1.54 45.22 161.18 50.58 12.36 58.49 8.88 35.26 5.92 61.98 233.47T60KI004 7.74 2.65 44.22 6.72 9.14 1.54 8.62 80.63 9.29 2.69 58.49 8.88 35.26 5.92 11.81 132.34T60KI006 49.22 14.88 54.05 8.21 22.31 3.75 53.30 205.72 59.07 15.09 71.48 10.86 86.13 14.47 73.05 330.15T60SO001 29.75 8.75 32.43 4.93 8.97 1.51 32.02 118.36 35.70 8.87 42.89 6.51 34.64 5.82 43.89 178.32T60SO002 40.31 12.18 44.22 6.72 18.07 3.04 43.64 168.18 48.38 12.35 58.49 8.88 69.72 11.71 59.82 269.35T60SO003 41.00 12.37 44.22 6.72 18.07 3.04 44.37 169.79 49.20 12.54 58.49 8.88 69.72 11.71 60.82 271.36T60SO004 52.82 15.37 54.05 8.21 13.06 2.19 56.74 202.44 63.39 15.59 71.48 10.86 50.43 8.47 77.77 297.99T60SO005 53.75 15.63 54.05 8.21 13.06 2.19 57.73 204.62 64.50 15.85 71.48 10.86 50.43 8.47 79.13 300.72

T65T65WG012 91.79 26.83 20.92 11.06 1.80 0.30 128.37 281.07T65WG013 138.24 40.34 20.92 11.06 1.80 0.30 193.30 405.96T65WG014 150.92 44.03 47.43 26.20 1.80 0.30 211.02 481.70

W25W25AO002 0.83 0.09 0.13 0.81 0.00 0.00 1.40 3.26W25AO003 1.20 0.13 0.13 0.81 0.00 0.00 2.04 4.31W25AO004 1.18 0.12 0.27 1.13 0.00 0.00 2.01 4.71W25AO005 2.40 0.25 0.54 1.76 0.00 0.00 4.07 9.02

2 259

EP 1110-1-8, Vol. 130 Nov 09

2-321


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)7/31/2009

1REGION

W25 cont.W25AO006 1.85 0.20 0.13 0.81 0.00 0.00 3.14 6.13W25CJ001 9.70 1.44 1.99 1.18 0.00 0.00 14.97 29.28W25CJ002 15.06 2.24 2.39 1.42 0.00 0.00 23.23 44.34W25CJ003 23.81 3.54 2.39 1.42 0.00 0.00 36.73 67.89W25KZ001 1.33 0.42 0.00 0.00 0.00 0.00 1.01 2.76W25KZ002 1.47 0.47 0.00 0.00 0.00 0.00 1.12 3.06W25KZ003 1.51 0.48 0.00 0.00 0.00 0.00 1.15 3.14W25KZ004 2.15 0.68 0.00 0.00 0.00 0.00 1.63 4.46W25KZ005 2.53 0.80 0.00 0.00 0.00 0.00 1.92 5.25W25KZ006 2.58 0.82 0.00 0.00 0.00 0.00 1.96 5.36W25KZ007 2.75 0.87 0.00 0.00 0.00 0.00 2.09 5.71W25NL001 14.19 1.50 26.98 12.81 0.00 0.00 26.28 81.76W25NL002 23.89 2.52 47.79 6.36 0.00 0.00 44.23 124.79W25NL003 15.31 1.62 21.40 2.85 0.00 0.00 28.34 69.52W25NL004 30.92 3.31 4.85 0.65 0.44 0.07 57.41 97.65W25NL005 58.60 6.18 99.86 13.29 0.00 0.00 108.49 286.42W25SD001 1.03 0.11 0.67 0.32 0.00 0.00 1.75 3.88W25SD002 2.66 0.28 0.40 0.19 0.00 0.00 4.52 8.05W25SD003 1.60 0.17 4.66 0.53 0.00 0.00 2.72 9.68W25SD004 2.29 0.25 2.07 0.24 0.04 0.01 3.91 8.81W25SD005 1.21 0.13 3.11 0.35 0.00 0.00 2.05 6.85W25SD006 1.10 0.12 0.13 4.06 0.00 0.00 1.87 7.28W25SD007 1.17 0.12 0.13 5.06 0.00 0.00 1.99 8.47W25SD008 1.28 0.13 0.13 6.06 0.00 0.00 2.17 9.77W25SD009 2.83 0.30 1.48 6.70 0.00 0.00 4.80 16.11W25XX005 0.39 0.04 1.29 0.15 0.00 0.00 0.66 2.53W25XX006 0.54 0.06 1.29 0.15 0.00 0.00 0.92 2.96

2 260

EP 1110-1-8, Vol. 130 Nov 09

2-322


TIRE REPAIR REPAIR


TIRE REPAIR REPAIR

TOTAL RATE DEPR

TIRE WEAR



EP 1110-1-8(Vol. 1)

7/31/2009

1REGION

W25 cont.W25XX007 0.72 0.08 2.07 0.24 0.00 0.00 1.23 4.34W25XX008 0.75 0.08 2.85 0.32 0.00 0.00 1.28 5.28W25XX009 1.51 0.16 2.07 0.24 0.00 0.00 2.57 6.55W25XX010 2.32 0.24 6.21 0.71 0.00 0.00 3.93 13.41

W30W30SO001 3.42 0.98 1.42 0.17 0.36 0.06 3.14 9.55W30SO002 4.10 1.17 1.42 0.17 0.36 0.06 3.76 11.04W30SO003 4.47 1.27 1.42 0.17 0.36 0.06 4.10 11.85W30SO004 2.26 0.63 0.00 0.01 0.00 0.00 1.72 4.62W30SO005 2.53 0.70 0.00 0.01 0.00 0.00 1.92 5.16W30SO006 2.91 0.81 0.00 0.01 0.00 0.00 2.21 5.94

W35W35LC010 0.08 0.01 0.64 0.30 0.00 0.00 0.06 1.09W35LC011 0.41 0.06 1.15 0.55 0.00 0.00 0.31 2.48W35LC012 0.52 0.08 1.49 0.71 0.00 0.00 0.40 3.20W35LC013 0.56 0.08 1.75 0.83 0.00 0.00 0.43 3.65W35LC018 0.12 0.02 0.21 0.10 0.00 0.00 0.09 0.54W35LC020 0.51 0.08 1.11 0.53 0.00 0.00 0.39 2.62W35XX020 0.22 0.05 2.38 0.27 0.00 0.00 0.28 3.20W35XX021 0.58 0.13 3.68 0.42 0.03 0.01 0.72 5.57W35XX022 0.59 0.13 3.90 0.44 0.03 0.01 0.74 5.84W35XX023 1.04 0.22 9.75 1.11 0.03 0.01 1.29 13.45W35XX024 1.54 0.33 5.78 0.66 0.03 0.01 1.91 10.26W35XX025 1.48 0.32 5.06 0.58 0.03 0.01 1.83 9.31

2 261

EP 1110-1-8, Vol. 130 Nov 09

2-323


EP 1110-1-8, Vol. 130 Nov 09

2-324

3-1

CHAPTER 3.0 - ADJUSTMENTS TO HOURLY RATES

SECTION I. GENERAL

3.1 Contents

This chapter explains the procedures for adjusting the hourly rates shown in tables 2-1 and 2-2.

3.2 Basis for Equipment Rates

The rates shown in tables 2-1 and 2-2 are based on the catalog list price of equipment manufactured in 2006 (3 years old). Area factors used to compute regional ownership and operating expenses are listed in appendix B. All equipment hourly rate elements for average and severe conditions are given in table 2-2. Individual cost elements, which comprise the total hourly rate, are shown in table 2-2. These hourly rate elements are listed by equipment ID No., which corresponds to the equipment shown in tables 2-1 and 2-2.

a. Ownership costs consist of two cost elements: depreciation (DEPR) and facilities capital cost of money (FCCM). These elements are located in tables 2-1 and 2-2.

b. Operating costs consist of five cost elements: fuel (FUEL); filters, oil, and grease (FOG); repairs (REPAIR); tire wear (TIRE WEAR); and tire repair (TIRE REPAIR). These elements are located in table 2-2.

3.3 Equipment Rate Adjustment Tables

Table 3-1 is used to adjust the ownership (DEPR + FCCM) portion of the average hourly rate and table 3-2 is used to adjust the standby hourly rate shown in table 2-1.

3.4 Determination for Use of Equipment Rates in Tables 2-1 and 2-2

The predetermined equipment rates in tables 2-1 and 2-2 may be used when the contractor’s actual cost data (cost or pricing data) is insufficient to calculate the rates. If the contractor’s actual equipment is listed in tables 2-1 and 2-2, the equipment must be equivalent. However, if the contractor’s actual equipment is not listed in tables 2-1 and 2-2, an equivalent piece of equipment may be chosen from the tables. To be considered equivalent, the contractor’s equipment must be no more or less than 10 percent of the configuration (size, capacity, and horsepower) and value as compared

EP 1110-1-8, Vol. 130 Nov 09

3-2

to the equipment in tables 2-1 and 2-2. In either case, if the equipment is not equivalent, the equipment rate must be calculated using the methodology in chapter 2.

SECTION II. RATE ADJUSTMENTS

3.5 Rate Adjustments

The ownership and/or the operating portion of the hourly rates and standby hourly rates shall be adjusted whenever one or more of the following rate adjustment conditions exist (rate adjustments are explained in detail in the following paragraphs).

• Changes in operating conditions • Changes in Cost of Money Rate • Actual work hours (hrs) exceed 40 hr per week (wk) • Changes in FUEL cost • Adjustments to FOG cost • Equipment of different age than table 2-1 • Rate adjustment for overage equipment • Rate adjustment for overage equipment standby

There are no rate adjustments for appendix B factors except for fuel cost (electric, gas, diesel off-road, and diesel on-road) and the Cost of Money Rate. Also, there are no rate adjustments for repairs, tire wear, or tire repair.

3.6 Changes in Operating Conditions

If difficult or severe conditions are justified by the Contracting Officer, selection or calculation of the appropriate rate is necessary. See chapter 2, section II, for definition of average, difficult, or severe conditions and determination of condition.

3.7 Change in Cost of Money Rate (CMR)

The Department of the Treasury adjusts the CMR (Prompt Payment Interest Rate) on or about 1 January and 1 July each year; these revisions are printed in the Federal Register. The Internet address for Prompt Payment Interest Rate is http://www.treasurydirect.gov/govt/rates/tcir/tcir_opdprmt2.htm.

EP 1110-1-8, Vol. 130 Nov 09

If the CMR shown in chapter 2, section VII, is not the current rate, the FCCM portion of the total hourly rate shall be adjusted upward or downward to match the CMR for the period of equipment use. See appendix I for a listing of historical CMRs. The total hourly rate adjusted for a differing CMR is computed by the formula:

Costs/hr Operating CMR) (OldCMR)] (NEW x [(FCCM/hr) DEPR/hr RateHourly Total ++=

Example: Assume that table 2-1 includes a crane [category (CAT) C80, subcategory (SUB) 0.02] with hourly costs as shown in the following example. The CMR has increased from 5.00 percent to a current rate of 6.00 percent (increase of 20 percent). The total hourly rate for this piece of equipment is determined as follows:

Assumptions for Total Hourly Rate with CMR of 5.00 percent (per hour):

DEPR $30.00FCCM $10.00Operating Costs (FUEL, FOG, TIRE WEAR, TIRE REPAIR, and REPAIR) $40.00 Total Hourly Rate (Based on a 40 hr/wk) $80.00

Adjustment Calculation of Total Hourly Rate for New CMR of 6.00 percent (per hour): $30.00/hr + [($10.00/hr) x (6.00%)] + $40.00/hr =$82.00/hr (5.00%) 3.8 Actual Work Hours Greater than 40 Hours per Week

If the actual number of work hours per week is greater than 40 hours, an adjustment shall be made to the FCCM element of the ownership cost. The FCCM is to be paid up to a maximum of 40 hours per week (7 calendar days). To calculate a multi-shift rate, prorate the 40-hour FCCM over the actual hours per week, as follows:

Total Hourly Rate = DEPR/hr + [(FCCM/hr) x (40 hr/wk)] + Operating Costs/hr (Actual Work hr/wk) Example: Assume that table 2-1 includes a crane (category C80, subcategory 0.02) with the below hourly costs. This crane worked 10 hours per day, 6 days per week (60 hours per week). The total hourly rate for this piece of equipment is determined as follows:

3-3

EP 1110-1-8, Vol. 130 Nov 09

Assumptions for Total Hourly Rate for 40 Hours/Week:

DEPR $30.00FCCM $10.00Operating Costs (FUEL, FOG, TIRE WEAR, TIRE REPAIR, and REPAIR) $40.00 Total Hourly Rate (Based on a 40 hr/wk) $80.00

Adjustment Calculation of Total Hourly Rate for 60 Hours/Week: $30.00/hr + [($10.00/hr) x (40 hr/wk)] + $40.00/hr =$76.67/hr (60 hr/wk) 3.9 Changes in Fuel Cost

Hourly fuel costs (including electricity) shall be adjusted in the event the average fuel prices at the jobsite vary by more than 10 percent above or below the price in appendix B. The contractor shall be required to furnish copies of all fuel supply contracts and invoices to the government to support fuel cost adjustment. Request for upward adjustment in the rates will be considered only when fuel is supplied by recognized distributors of bulk quantities. Mathematically, this is the ratio of the new fuel cost divided by the fuel cost (appendix B). To calculate the total hourly rate, apply the ratio of fuel cost, as follows:

( )( ) FUEL/hr] x

B Appendix in Cost FuelCost FuelNew [ REPAIR/hr)

REPAIR/hr TIRE WEAR/hrTIRE (FOG/hr FCCM/hr) (DEPR/hr RateHourly Total

+

+++++=

Example: Assume that table 2-1 includes a crane (category C80, subcategory 0.02) with the below hourly costs. Assume the fuel cost (diesel off-road) in appendix B is $2.50/gal and the current fuel cost has increased to $3.00/gal (increase of 20.00 percent). The total hourly rate for this piece of equipment can be determined as follows: Assumptions for Fuel Cost (based on $2.50/gal from appendix B) per hour:

DEPR $30.00FCCM $10.00FOG, TIRE WEAR, TIRE REPAIR, and REPAIR) $30.00FUEL $10.00 Total Hourly Rate $80.00

3-4

EP 1110-1-8, Vol. 130 Nov 09

3-5

Adjustment Calculation for hourly FUEL cost using the new fuel cost of $3.00/gal: ($30.00/hr + $10.00/hr) + $30.00/hr + [($3.00/gal) x $10.00/hr] =$82.00/hr ($2.50/gal) 3.10 Adjustments to Fuel, Oil, and Grease (FOG) Cost

The hourly FOG allowance shall also be adjusted upward or downward by applying the same ratio (new fuel cost divided by fuel cost shown in appendix B) as the fuel costs change using the methodology as shown in paragraph 3-9.

3.11 Equipment of Different Age than Table 2-1

When the age of the equipment is newer or older than the age of the equipment listed in table 2-1, table 3-1 factors may be used to adjust the hourly rate (see paragraph 3-12 for guidance on overage equipment), otherwise the step-by-step calculation method (as shown in figure 2-1) is necessary. To adjust the hourly rate using the tables, the factors given in table 3-1 are multiplied by the hourly ownership costs shown in table 2-1. The result is an ownership rate adjusted for the actual age of the equipment. Note: Age adjustment factors in tables 3-1 and 3-2 vary by region.

a. When the age of a unit of equipment is older than the age of the equipment listed in table 2-1 (purchased new in 2006) and does not exceed the years of economic life, adjust the hourly rate as shown in the next example. The years of economic life is determined by dividing hours of LIFE (from appendix D) by Working Hours Per Year (WHPY) (from appendix B).

Example: Assume that table 2-1 includes a crane (category C80, subcategory 0.02) manufactured in 2006 and has a total hourly rate of $65 per hour and an ownership rate of $30 per hour. If an equivalent crane owned by a contractor was manufactured in 2002, the total hourly rate is determined as follows: Table 2-1 Rate and Adjustment Calculation: Total hourly rate = $65.00/hr Ownership rate 2006 (DEPR + FCCM) = -($30.00)/hr Ownership rate 2002 adjusted for age (Ownership rate = $30) x (0.84 the age adjustment factor from table 3-1, for category C80, subcategory 0.02, and for the year 2002.) = +$25.20/hr Total hourly rate for equipment manufactured in 2002 = $60.20/hr

EP 1110-1-8, Vol. 130 Nov 09

3-6

b. When the unit of equipment is older than the age of equipment listed in table 2-1 (purchased new in 2006) and exceeds the years of economic life, adjust the hourly rate as shown in the example for overage equipment in paragraph 3-12.

c. When the unit of equipment is newer than the equipment listed in table 2-1 (purchased new in 2006), use the adjustment factor in table 3-1 for the year of manufacture. If the equipment is newer than the most recent year shown in table 3-1, use the adjustment factor in the column of the most recent year. Once the adjustment factor is determined from table 3-1, complete the adjustment calculation as shown in the example above. The step-by-step calculation method shown in figure 2-1 may also be used.

3.12 Rate Adjustment for Overage Equipment

If the contractor’s equipment exceeds the economic life in hours (from appendix D), it is considered overage, and the rates shall be adjusted.

a. The total hourly operating rate for overage equipment (no matter how old) shall be computed on the basis that the equipment is as old as possible "without" exceeding the hours of LIFE as shown in appendix D. Tables 3-1 and 3-2 show factors for the economic life for equipment based on the current pamphlet year (e.g., manufactured in 2006). Select a comparable unit of equipment (horsepower, value, capacity, and size) shown in table 2-1, the total hourly rate can be computed as shown in the following example. If there is no comparable unit of equipment in table 2-1, follow the methodology presented in figure 3-1.

b. The ownership portion of the rate shall be adjusted for equipment that is overage. This adjusted rate is not to exceed the rate for the same unit of equipment that is not overage.

Example: Assume that table 2-1 includes a crane (category C80, subcategory 0.02) manufactured in 2006, has a total hourly rate of $65 per hour, and an ownership rate of $30 per hour. If an equivalent crane owned by a contractor was manufactured in 1992 (maximum life 1998), this crane is overage and the total hourly rate is determined as follows:

EP 1110-1-8, Vol. 130 Nov 09

3-7

Table 2-1 Rate and Adjustment Calculation: Total hourly rate = $65.00/hr Ownership rate 2006 (DEPR + FCCM) = -($30.00)/hr Ownership rate 1992 adjusted for age (Ownership rate = $30.00) x (0.78) use the oldest age adjustment factor from table 3-1, for category C80, subcategory 0.02, the last year shown.) = +$23.40/hr Total hourly rate for equipment manufactured in 1992 = $58.40/hr 3.13 Standby Rate Adjustment for Equipment of a Different Age than Table 2-1

If the equipment age is other than listed in table 2-1 (purchased new in 2006), adjustment to the hourly standby rate is required. When the age of the equipment is newer or older than the age of the equipment listed in table 2-1, table 3-2 factors may be used to adjust the hourly rate, otherwise the step-by-step calculation method is necessary. The result is a standby rate adjusted for the actual age of the equipment.

a. Standby rates for overage equipment are based on the actual age of the equipment. The age adjustment factor given in table 3-2 is multiplied by the hourly standby cost shown in table 2-1 for the listed or comparable unit of equipment. This results in a standby rate adjusted for the actual age of the unit of equipment being considered.

Hourly Standby Rate Adjusted for Actual Age = Hourly Standby Rate x Age Adjustment Factor

Example: Assume that table 2-1 includes a crane (category C80, subcategory 0.02) manufactured in 2006 and has a standby rate of $20.00 per hour. If an equivalent crane owned by a contractor was manufactured in 1998, the hourly standby rate is determined as follows: Hourly Standby Rate (table 2-1) =$20.00/hr Age Adjustment Factor (table 3-2) = 0.78

for category C80, subcategory 0.02, and for 1998 (actual year of manufacture)

Adjustment Calculation: Hourly Standby Rate Adjusted for Actual Age =$20.00/hr (Hourly Standby Rate) x 0.78 (Age Adjustment Factor) =$15.60/hr b. When the unit of equipment is newer than the equipment listed in table 2-1 (purchased new in 2006), use the adjustment factor in table 3-2 for the year

EP 1110-1-8, Vol. 130 Nov 09

3-8

of manufacture. Once the adjustment factor is determined from table 3-2, complete the adjustment calculation as shown in the example above. The step-by-step calculation method shown in figure 3-2 may also be used.

c. When the equipment age is older than the last year shown in table 3-2 or newer than the first year shown in table 3-2, the standby rate must be calculated using the step-by-step methodology shown in figure 3-2.

3.14 Equipment Purchased Used

A detailed methodology for computing a total hourly rate for equipment purchased used is not included in this pamphlet.

a. When actual cost data in accordance with chapter 1 is not available, an hourly rate and standby rate for equipment purchased used can be computed on the basis that the equipment was purchased new by the contractor in the year it was manufactured. Consideration for the actual age of used equipment may require an adjustment for overage.

b. The condition of the used equipment at the time of purchase should consider the extent of capital improvements, mechanical condition, and previous hours of operation. These conditions are difficult or impossible to determine and evaluate when computing a total hourly rate based on actual acquisition cost.

3.15 Rate Calculation Examples

Figure 3-1 illustrates how total hourly rates are adjusted for overage equipment. Figure 3-2 gives a sample calculation for computing adjusted standby rates.

EP 1110-1-8, Vol. 130 Nov 09

Table 3-1. Equipment Age Adjustment Factors

for

Ownership Costs

The factors in this table are used when the age of a unit of equipment is other than the age of the equipment listed in table 2-1 (purchased new in 2006).

The factors are multiplied by the hourly ownership costs (shown in table 2-1) and result in an ownership rate adjusted for the actual age of the equipment being considered.

When the actual “life” in hours of the unit of equipment has exceeded the economic life given in appendix D, the age will be determined as discussed in chapter 3.

Refer to chapter 3, as follows:

3-11. Equipment of Different Age than Table 2-1

3-12. Rate Adjustment for Overage Equipment

3-9

EP 1110-1-8, Vol. 130 Nov 09

Table 3-1 Equipment Age Adjustment Factors for Ownership CostYear Purchased NewLife in Years

CATEGORY

SUB TYPE OF EQUIPMENT 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998 1997 1996 1995 1994 1993 1992

REGION 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

7/31/2009(Vol. 1)

A10 0.00 AGGREGATE / CHIP SPREADERS

A10 0.10 SELF-PROPELLED 1.13 1.08 1.03 1.00 0.95 0.89

A10 0.20 TOWED & TAILGATE 1.13 1.08 1.03 1.00 0.95

A15 0.00 AIR COMPRESSORS, PORTABLE

A15 0.10 ROTARY SCREW 1.20 1.12 1.05 1.00 0.96 0.92 0.91 0.91

A15 0.20 SHOP TYPE 1.19 1.11 1.04 1.00 0.96 0.92 0.92 0.92 0.92

A20 0.00 AIR HOSE, TOOLS & EQUIPMENT

A20 0.10 AIR DRILL HOSE 1.17 1.11 1.04 1.00

A20 0.20 SANDBLAST HOSE 1.17 1.11 1.04 1.00

A20 0.30 SANDBLASTERS, BREAKERS, & MISC. AIR TOOLS 1.18 1.11 1.04 1.00 0.96

A25 0.00 ASPHALT PAVING DISTRIBUTORS 1.12 1.07 1.03 1.00 0.96

A30 0.00 ASPHALT PAVERS & MISCELLANEOUS ROAD EQUIPMENT

A30 0.10 SELF PROPELLED 1.12 1.07 1.03 1.00 0.95 0.90

A30 0.20 TOWED 1.13 1.08 1.03 1.00 0.95 0.89 0.90 0.90

A30 0.30 SLURRY SEAL PAVERS (Cold mix) 1.13 1.08 1.03 1.00 0.95 0.90 0.90 0.90 0.90

A30 0.40 MISCELLANEOUS ROAD EQUIPMENT 1.13 1.08 1.03 1.00 0.95 0.89 0.90 0.90

A35 0.00 ASPHALT PAVING KETTLES 1.13 1.08 1.03 1.00 0.95

A40 0.00 ASPHALT & CONCRETE MILLERS / PROFILERS / PLANERS / ROTARY GRINDERS

1.13 1.08 1.03 1.00 0.95

A45 0.00 ASPHALT RECYCLERS & SEALERS 1.13 1.08 1.03 1.00

B10 0.00 BATCH PLANTS, ASPHALT & CONCRETE

B10 0.10 ASPHALT 1.13 1.08 1.03 1.00 0.95 0.89

B10 0.20 CONCRETE 1.13 1.08 1.03 1.00 0.95 0.89

3- 9

EP 1110-1-8, Vol. 130 Nov 09

3-10


CATEGORY


REGION 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

7/31/2009(Vol. 1)

B10 0.30 PUGMILL 1.13 1.08 1.03 1.00 0.95 0.89 0.90 0.90

B15 0.00 BROOMS, STREET SWEEPERS & FLUSHERS 1.11 1.06 1.03 1.00 0.96 0.89

B20 0.00 BRUSH CHIPPERS 1.11 1.06 1.03 1.00 0.96 0.89

B25 0.00 BUCKETS, CLAMSHELL 1.06 1.02 1.01 1.00 0.94 0.89

B30 0.00 BUCKETS, CONCRETE

B30 0.10 GENERAL PURPOSE, MANUAL TRIP 1.06 1.02 1.01 1.00 0.95 0.89

B30 0.20 LAYDOWN 1.06 1.02 1.01 1.00 0.95 0.89

B30 0.30 LOWBOY 1.06 1.02 1.01 1.00 0.95 0.89

B30 0.40 LOW SLUMP 1.06 1.02 1.01 1.00 0.95 0.89

B35 0.00 BUCKETS, DRAGLINE

B35 0.10 LIGHT WEIGHT 1.06 1.02 1.01 1.00 0.94 0.89

B35 0.20 MEDIUM WEIGHT 1.06 1.02 1.01 1.00 0.94 0.89 0.86

B35 0.30 HEAVY WEIGHT 1.06 1.02 1.01 1.00 0.94 0.89 0.86 0.84

C05 0.00 CHAIN SAWS 1.11 1.06 1.00

C10 0.00 COMPACTORS, WALK-BEHIND OR REMOTE CONTROLLER

C10 0.10 COMPACTORS, RAMMERS / TAMPERS & VIBRATORY PLATES 1.11 1.06 1.02 1.00

C10 0.20 ROLLERS, VIBRATORY 1.12 1.07 1.03 1.00

C15 0.00 CONCRETE CLEANERS / ABRASIVE BLASTERS

C15 0.10 WALK BEHIND 1.13 1.07 1.03 1.00

C15 0.20 TRUCK/TRAILER MOUNTED 1.12 1.07 1.03 1.00 0.95 0.88

C20 0.00 CONCRETE BUGGIES 1.13 1.07 1.03 1.00

C25 0.00 CONCRETE FINISHERS/SCREEDS/SPREADERS

3- 10

EP 1110-1-8, Vol. 130 Nov 09

3-11


CATEGORY


REGION 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

7/31/2009(Vol. 1)

C25 0.10 FINISHERS/TROWELS 1.13 1.07 1.03 1.00

C25 0.20 VIBRATORY SCREED 1.13 1.07 1.03 1.00

C25 0.25 VIBRATORY LASER SCREED 1.14 1.08 1.03 1.00 0.94 0.87

C25 0.30 MATERIAL/TOPPING SPREADERS 1.14 1.08 1.03 1.00 0.94 0.87

C30 0.00 CONCRETE GRINDERS 1.13 1.07 1.03 1.00

C35 0.00 CONCRETE GUNITERS / SHOTCRETERS 1.13 1.07 1.03 1.00 0.95 0.87

C40 0.00 CONCRETE MIXING UNITS 1.13 1.07 1.03 1.00

C45 0.00 CONCRETE PAVING MACHINES 1.13 1.08 1.03 1.00 0.95

C55 0.00 CONCRETE PUMPS 1.11 1.06 1.03 1.00 0.96 0.89

C60 0.00 CONCRETE SAWS (Add cost for sawblade wear) 1.11 1.06 1.03 1.00 0.95

C65 0.00 CONCRETE VIBRATORS 1.18 1.11 1.04 1.00

C70 0.00 CRANES, GANTRY & STRADDLE

C75 0.00 CRANES, HYDRAULIC, SELF-PROPELLED 1.06 1.02 1.01 1.00 0.94 0.88 0.86 0.83 0.78 0.79 0.78

C80 0.00 CRANES, HYDRAULIC, TRUCK MOUNTED

C80 0.01 UNDER 26 TON 1.06 1.02 1.01 1.00 0.94 0.88 0.86 0.83 0.78 0.79 0.78

C80 0.02 26 TON THRU 65 TON 1.06 1.02 1.01 1.00 0.94 0.89 0.86 0.84 0.78 0.79 0.79 0.78

C80 0.03 66 TON THRU 125 TON 1.06 1.02 1.01 1.00 0.94 0.89 0.86 0.84 0.78 0.79 0.79 0.78 0.76 0.74

C80 0.04 OVER 125 TON 1.06 1.02 1.01 1.00 0.94 0.89 0.86 0.84 0.78 0.79 0.79 0.78 0.76 0.74 0.72

C85 0.00 CRANES, MECHANICAL, LATTICE BOOM, CRAWLER MOUNTED

C85 0.11 DRAGLINE, CLAMSHELL, 0 THRU 1.0 CY 1.06 1.03 1.01 1.00 0.94 0.88 0.85 0.83 0.77 0.78 0.78

C85 0.12 DRAGLINE, CLAMSHELL, OVER 1.0 CY THRU 2.5 CY 1.06 1.03 1.01 1.00 0.94 0.88 0.86 0.83 0.77 0.78 0.78 0.77

C85 0.13 DRAGLINE, CLAMSHELL, OVER 2.5 CY THRU 5.0 CY 1.06 1.02 1.01 1.00 0.94 0.88 0.86 0.83 0.77 0.78 0.78 0.77 0.75 0.73

3- 11

EP 1110-1-8, Vol. 130 Nov 09

3-12


CATEGORY


REGION 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

7/31/2009(Vol. 1)

C85 0.14 DRAGLINE, CLAMSHELL, OVER 5.0 CY 1.06 1.02 1.01 1.00 0.94 0.88 0.86 0.83 0.77 0.79 0.78 0.77 0.75 0.73 0.71

C85 0.21 LIFTING, 0 THRU 25 TON 1.06 1.03 1.01 1.00 0.94 0.88 0.86 0.83 0.77 0.78 0.78 0.77

C85 0.22 LIFTING, 26 TON THRU 50 TON 1.06 1.02 1.01 1.00 0.94 0.88 0.86 0.83 0.77 0.78 0.78 0.77 0.75 0.73

C85 0.23 LIFTING, 51 TON THRU 150 TON 1.06 1.02 1.01 1.00 0.94 0.89 0.86 0.84 0.78 0.79 0.79 0.78 0.76 0.74 0.72

C85 0.24 LIFTING, OVER 150 TON 1.06 1.02 1.01 1.00 0.94 0.89 0.86 0.84 0.78 0.79 0.79 0.78 0.76 0.74 0.72 0.71 0.70

C90 0.00 CRANES, MECHANICAL, LATTICE BOOM, TRUCK MOUNTED

C90 0.01 UNDER 26 TON 1.06 1.02 1.01 1.00 0.94 0.88 0.86 0.83 0.78 0.79 0.78

C90 0.02 26 TON THRU 65 TON 1.06 1.02 1.01 1.00 0.94 0.89 0.86 0.84 0.78 0.79 0.79 0.78

C90 0.03 66 TON THRU 125 TON 1.06 1.02 1.01 1.00 0.94 0.88 0.86 0.83 0.77 0.78 0.78 0.77 0.75 0.73

C90 0.04 OVER 125 TON 1.06 1.02 1.01 1.00 0.94 0.88 0.86 0.83 0.77 0.79 0.78 0.77 0.75 0.73 0.71

C95 0.00 CRANES, TOWER 1.06 1.02 1.01 1.00 0.94 0.88 0.86 0.83 0.77 0.78 0.78 0.77 0.75 0.73

D10 0.00 DRILLS, AIR/HYDRAULIC,CRWLR MTD,0" THRU 6.5" DIA HOLE (Add cost for drill steel and bit wear)

D10 0.10 DRILLS, AIR TRACK (Add cost for drill steel and bit wear) 1.22 1.17 1.08 1.00 0.92 0.84 0.78 0.76 0.68 0.66 0.65

D10 0.20 DRILLS, HYDRAULIC TRACK (Add cost for drill steel and bit wear) 1.23 1.17 1.09 1.00 0.91 0.83 0.77 0.75

D15 0.00 DRILLS, HORIZONTAL BORING & GROUND PIERCING (Add cost for drill steel and bit wear)

1.23 1.17 1.09 1.00 0.91 0.83 0.77 0.75

D20 0.00 DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit wear) 1.24 1.18 1.09 1.00 0.91 0.83

D25 0.00 DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear) 1.23 1.17 1.09 1.00 0.91 0.83 0.77 0.75

D30 0.00 DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear) 1.23 1.17 1.09 1.00 0.91 0.83 0.77 0.75

D35 0.00 DRILLS, ROTARY BLASTHOLE (Add cost for drill steel and bit wear)

D35 0.11 DIESEL, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit wear)

1.21 1.16 1.08 1.00 0.92 0.85 0.79 0.77 0.70 0.68 0.67

D35 0.12 DIESEL, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear) 1.21 1.16 1.08 1.00 0.92 0.85 0.79 0.77 0.71 0.69 0.67 0.66 0.65 0.64

D35 0.21 ELECTRIC, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit wear)

1.21 1.16 1.08 1.00 0.92 0.85 0.79 0.77 0.70 0.68 0.67

3- 12

EP 1110-1-8, Vol. 130 Nov 09

3-13


CATEGORY


REGION 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

7/31/2009(Vol. 1)

D35 0.22 ELECTRIC, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear) 1.21 1.16 1.08 1.00 0.92 0.85 0.79 0.77 0.71 0.69 0.67 0.66 0.65 0.64

F10 0.00 FORK LIFTS 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83

G10 0.00 GENERATOR SETS

G10 0.10 PORTABLE 1.16 1.11 1.05 1.00 0.95 0.90

G10 0.20 SKID MOUNTED 1.16 1.11 1.05 1.00 0.95 0.90 0.88 0.88

G15 0.00 GRADERS, MOTOR 1.11 1.06 1.02 1.00 0.96 0.91 0.87 0.86 0.85 0.84 0.82

H10 0.00 HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear) 1.13 1.07 1.03 1.00 0.95

H13 0.00 HAZARDOUS/TOXIC WASTE EQUIPMENT

H13 0.11 COMPACTORS (Compression force) 0 THRU 50 TONS 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84

H13 0.12 COMPACTORS (Compression force) OVER 50 TONS 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82

H13 0.21 FILTER PRESSES, STATIONARY 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83

H13 0.22 FILTER PRESSES, MOBILE 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84

H13 0.30 CENTRIFUGES 1.13 1.07 1.03 1.00

H13 0.40 SHREDDERS 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84

H13 0.51 SOIL TREATMENT PLANT, MOBILE 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84

H13 0.61 SLUDGE PROCESSING EQUIP, SLUDGE DISPENSERS 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84

H13 0.71 WASTE HANDLING EQUIPMENT, DRUM HANDLING 1.12 1.07 1.03 1.00

H15 0.00 HEATERS, SPACE

H20 0.00 HOISTS & AIR WINCHES 1.12 1.07 1.03 1.00 0.95 0.88 0.85

H25 0.00 HYDRAULIC EXCAVATORS, CRAWLER MOUNTED

H25 0.10 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS) 1.07 1.03 1.02 1.00 0.93 0.87

H25 0.11 OVER 12,500 LBS THRU 40,000 LBS 1.07 1.03 1.02 1.00 0.93 0.87 0.84

3- 13

EP 1110-1-8, Vol. 130 Nov 09

3-14


CATEGORY


REGION 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

7/31/2009(Vol. 1)

H25 0.12 OVER 40,000 LBS THRU 100,000 LBS 1.07 1.03 1.01 1.00 0.94 0.87 0.85 0.82 0.75

H25 0.13 OVER 100,000 LBS THRU 160,000 LBS 1.07 1.03 1.01 1.00 0.94 0.88 0.85 0.82 0.76 0.77 0.77 0.76

H25 0.14 OVER 160,000 LBS 1.07 1.03 1.01 1.00 0.94 0.88 0.85 0.83 0.76 0.78 0.77 0.76 0.74 0.72

H25 0.21 ATTACHMENTS, MOBILE SHEARS 1.12 1.07 1.03 1.00 0.95

H25 0.22 ATTACHMENTS, MATERIAL HANDLING 1.13 1.07 1.03 1.00 0.95

H25 0.23 ATTACHMENTS, CONCRETE PULVERIZERS 1.12 1.07 1.03 1.00 0.95

H25 0.24 ATTACHMENTS, COMPACTORS 1.12 1.07 1.03 1.00 0.95

H30 0.00 HYDRAULIC EXCAVATORS, WHEEL MOUNTED

H30 0.01 0 THRU 1.0 CY 1.07 1.03 1.02 1.00 0.93 0.87

H30 0.02 OVER 1.0 CY 1.07 1.03 1.02 1.00 0.93 0.87 0.84 0.81

H35 0.00 HYDRAULIC SHOVELS, CRAWLER MOUNTED

H35 0.11 DIESEL, 0 CY THRU 5.0 CY 1.06 1.03 1.01 1.00 0.94 0.88 0.85 0.83 0.77 0.78 0.78

H35 0.12 DIESEL, OVER 5.0 CY 1.06 1.03 1.01 1.00 0.94 0.88 0.86 0.83 0.77 0.78 0.78 0.77

H35 0.21 ELECTRIC, OVER 2.5 CY 1.06 1.02 1.01 1.00 0.94 0.88 0.86 0.83 0.77 0.78 0.78 0.77 0.75 0.73

L10 0.00 LAND CLEARING EQUIPMENT 1.13 1.06 1.02 1.00 0.96 0.90 0.87 0.86

L15 0.00 LANDSCAPING EQUIPMENT 1.12 1.07 1.03 1.00

L20 0.00 LIGHTING SETS, TRAILER MOUNTED

L20 0.10 METALLIC VAPOR 1.12 1.07 1.03 1.00 0.95 0.88

L25 0.00 LINE STRIPING EQUIPMENT 1.12 1.07 1.03 1.00 0.95 0.88

L30 0.00 LOADERS, BELT (Conveyor belts) & ACCESSORIES 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83

L35 0.00 LOADERS, FRONT END, CRAWLER TYPE 1.13 1.06 1.02 1.00 0.96 0.90 0.87 0.86

L40 0.00 LOADERS, FRONT END, WHEEL TYPE

3- 14

EP 1110-1-8, Vol. 130 Nov 09

3-15


CATEGORY


REGION 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

7/31/2009(Vol. 1)

L40 0.11 ARTICULATED, 0 THRU 225 HP 1.14 1.07 1.02 1.00 0.95 0.90 0.86

L40 0.12 ARTICULATED, OVER 225 HP 1.13 1.06 1.02 1.00 0.96 0.90 0.87 0.86 0.85 0.85

L40 0.20 SKID STEER 1.13 1.06 1.02 1.00 0.96 0.90

L40 0.21 SKID STEER ATTACHMENTS 1.13 1.06 1.02 1.00

L40 0.31 TOOL CARRIER & TELESCOPIC HANDLERS, 0 THRU 225 HP 1.13 1.07 1.02 1.00 0.95 0.90 0.87 0.85

L40 0.32 TOOL CARRIER & TELESCOPIC HANDLERS, OVER 225 HP 1.12 1.06 1.02 1.00 0.96 0.91 0.88 0.86 0.86

L45 0.00 LOADERS / BACKHOE, CRAWLER TYPE 1.13 1.06 1.02 1.00 0.95 0.90

L50 0.00 LOADERS / BACKHOE, WHEEL TYPE 1.13 1.07 1.02 1.00 0.95 0.90 0.87 0.85

L55 0.00 LOADER / BACKHOE, ATTACHMENTS 1.13 1.07 1.03 1.00 0.95

L60 0.00 LOG SKIDDERS 1.17 1.11 1.05 1.00 0.95 0.91 0.86 0.84

M10 0.00 MARINE EQUIPMENT (NON DREDGING)

M10 0.11 AQUATIC MAINTENANCE 1.14 1.09 1.05 1.00 0.96 0.92 0.87 0.82

M10 0.12 AQUATIC MAINTENANCE ATTACHMENTS 1.15 1.10 1.05 1.00 0.96

M10 0.21 HYDRAULIC CUTTERHEAD DREDGE, 8" OR LESS,TRANSPORTABLE 1.13 1.09 1.05 1.00 0.96 0.93 0.87 0.83 0.82 0.80 0.79 0.78

M10 0.22 HYDRAULIC CUTTERHEAD DREDGE,8" - 12",TRANSPORTABLE 1.13 1.09 1.05 1.00 0.96 0.93 0.87 0.83 0.82 0.80 0.79 0.78

M10 0.23 HYDRAULIC AUGERHEAD DREDGE,12" OR LESS,TRANSPORTABLE 1.13 1.09 1.05 1.00 0.96 0.93 0.87 0.83 0.82 0.80 0.79 0.78

M10 0.24 HYDRAULIC FLOATING PUMPS,12" OR LESS,TRANSPORTABLE 1.14 1.09 1.05 1.00 0.96 0.93

M10 0.25 HYDRUALIC DREDGE PUMPS,12" OR LESS,TRANSPORTABLE 1.15 1.09 1.05 1.00 0.96

M10 0.26 HYDRAULIC DREDGE / PUMP ATTACHMENTS 1.15 1.09 1.05 1.00 0.96

M10 0.31 SMALL MECH DREDGES,CLAMSHELL,BARGE-MTD TO 5 CY 1.06 1.02 1.01 1.00 0.94 0.89 0.86 0.84 0.78 0.79 0.79 0.78 0.76 0.74

M10 0.32 SMALL MECH DREDGES, AMPHIBIOUS EXCAVATORS 1.06 1.02 1.01 1.00 0.94 0.88 0.86 0.83

M10 0.33 SMALL MECH DREDGES,HOE-MOUNTED DREDGING ATTACH 1.14 1.09 1.05 1.00 0.96 0.92 0.87 0.83 0.82 0.80 0.78 0.78 0.76 0.73 0.70

3- 15

EP 1110-1-8, Vol. 130 Nov 09

3-16


CATEGORY


REGION 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

7/31/2009(Vol. 1)

M10 0.41 WORK FLOATS (NON-DREDGING) 1.14 1.09 1.05 1.00 0.96

M10 0.42 WORK BARGES (SECTIONAL, NON-DREDGING) 1.13 1.08 1.05 1.00 0.96 0.93 0.88 0.84 0.83 0.81 0.79 0.79 0.78 0.75 0.72 0.70 0.69 0.66

M10 0.45 FLAT-DECK OR CARGO BARGE (NON-DREDGING) 1.12 1.08 1.04 1.00 0.96 0.93 0.88 0.85 0.84 0.82 0.81 0.80 0.79 0.76 0.73 0.72 0.71 0.68

M10 0.46 DUMP SCOW (NON-DREDGING) 1.12 1.08 1.04 1.00 0.96 0.93 0.88 0.85 0.84 0.82 0.81 0.80 0.79 0.76 0.73 0.72 0.71 0.68

M10 0.47 DRILL BARGE (NON-DREDGING) 1.13 1.08 1.04 1.00 0.96 0.93 0.88 0.84 0.83 0.81 0.80 0.79 0.78 0.75 0.72 0.71 0.70 0.67

M10 0.48 ALL OTHER BARGES (NON-DREDGING) 1.13 1.08 1.04 1.00 0.96 0.93 0.88 0.84 0.83 0.81 0.80 0.79 0.78 0.75 0.72 0.71 0.70 0.67

M10 0.51 BOATS & LAUNCHES, 0 THRU 250 HP 1.14 1.09 1.05 1.00 0.96 0.92 0.87 0.83 0.82 0.79 0.78 0.77

M10 0.53 BOATS & LAUNCHES, 251 THRU 500 HP 1.13 1.09 1.05 1.00 0.96 0.93 0.87 0.84 0.82 0.80 0.79 0.78 0.77 0.74

M10 0.54 TUGS, 501 THRU 1,000 HP 1.13 1.08 1.04 1.00 0.96 0.93 0.88 0.84 0.83 0.81 0.80 0.79 0.78 0.75 0.72 0.71 0.70 0.67

M10 0.55 TUGS, 1,000 THRU 2,000 HP 1.13 1.08 1.04 1.00 0.96 0.93 0.88 0.84 0.83 0.81 0.80 0.80 0.78 0.76 0.73 0.71 0.70 0.67

P10 0.00 PILE HAMMER ACCESSORIES - EXTRACTORS & BOX LEADS 1.15 1.09 1.04 1.00 0.94

P20 0.00 PILE HAMMERS, DOUBLE ACTING

P20 0.10 DIESEL 1.13 1.08 1.03 1.00 0.95

P20 0.20 PNUEMATIC (STEAM/AIR) 1.13 1.07 1.03 1.00 0.95

P25 0.00 PILE HAMMERS, SINGLE ACTING

P25 0.10 DIESEL 1.13 1.07 1.03 1.00 0.95

P25 0.20 PNUEMATIC (STEAM/AIR) 1.12 1.07 1.03 1.00 0.95

P30 0.00 PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORY 1.13 1.07 1.03 1.00 0.95

P35 0.00 PIPELAYERS 1.12 1.06 1.02 1.00 0.96 0.90 0.88 0.86 0.85 0.85 0.84

P40 0.00 PLATFORMS & MAN-LIFTS 1.06 1.02 1.01 1.00 0.94 0.89

P45 0.00 PUMPS, GROUT 1.12 1.07 1.03 1.00 0.95 0.89

P50 0.00 PUMPS, WATER, CENTRIFUGAL, TRASH

3- 16

EP 1110-1-8, Vol. 130 Nov 09

3-17


CATEGORY


REGION 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

7/31/2009(Vol. 1)

P50 0.11 ENGINE DRIVE 1.12 1.07 1.03 1.00 0.95 0.88

P50 0.12 ELECTRIC DRIVE 1.12 1.07 1.03 1.00 0.95 0.88

P50 0.21 WHEEL MOUNTED, ENGINE DRIVE 1.12 1.07 1.03 1.00 0.95 0.88

P50 0.22 WHEEL MOUNTED, ELECTRIC DRIVE 1.12 1.07 1.03 1.00 0.95 0.88

P50 0.31 HOSES, PUMP, SUCTION & DISCHARGE 1.11 1.06 1.03 1.00

P55 0.00 PUMPS, WATER, SUBMERSIBLE

P55 0.01 ENGINE DRIVE 1.12 1.07 1.03 1.00 0.95 0.88

P55 0.02 ELECTRIC DRIVE 1.12 1.07 1.03 1.00 0.95 0.89

P60 0.00 PUMPS, WATER, CENTRIFUGAL, DEWATERING

P60 0.11 SKID MOUNTED, ENGINE DRIVE 1.12 1.07 1.03 1.00 0.95 0.88

P60 0.12 SKID MOUNTED, ELECTRIC DRIVE 1.12 1.07 1.03 1.00 0.95 0.89



P65 0.00 PUMPS, WATER, DIAPHRAGM

P65 0.11 SKID MOUNTED, ENGINE DRIVE 1.12 1.07 1.03 1.00 0.95 0.88

P65 0.12 SKID MOUNTED, ELECTRIC DRIVE 1.12 1.07 1.03 1.00 0.95 0.89



P70 0.00 PUMPS, WATER (For core drills)

P70 0.01 ENGINE DRIVE 1.13 1.07 1.03 1.00 0.95 0.87

P70 0.02 ELECTRIC DRIVE 1.13 1.07 1.03 1.00 0.95 0.87

R10 0.00 RIPPERS & HYDRAULIC BANK SLOPERS (Add cost for point wear) 1.13 1.06 1.02 1.00 0.95 0.90

3- 17

EP 1110-1-8, Vol. 130 Nov 09

3-18


CATEGORY


REGION 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

7/31/2009(Vol. 1)

R15 0.00 ROLLERS, STATIC, TOWED, PNEUMATIC 1.18 1.12 1.06 1.00 0.95 0.90 0.85 0.83

R20 0.00 ROLLERS, STATIC, TOWED, STEEL DRUM 1.18 1.12 1.06 1.00 0.95 0.90 0.85 0.83

R30 0.00 ROLLERS, STATIC, SELF-PROPELLED

R30 0.01 PNEUMATIC 1.17 1.11 1.05 1.00 0.95 0.91

R30 0.02 SMOOTH DRUM 1.17 1.11 1.05 1.00 0.95 0.91 0.86 0.84

R30 0.03 TAMPING FOOT, LANDFILL & SOIL COMPACTORS 1.18 1.12 1.05 1.00 0.95 0.90 0.86 0.83 0.82

R40 0.00 ROLLERS, VIBRATORY, TOWED 1.18 1.12 1.06 1.00 0.95 0.90

R45 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM 1.18 1.12 1.06 1.00 0.95 0.90

R50 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE DRUM 1.19 1.13 1.06 1.00 0.94 0.89

R55 0.00 ROOFING EQUIPMENT 1.12 1.07 1.03 1.00 0.95

S10 0.00 SCRAPERS, ELEVATING

S10 0.01 0 THRU 200 HP 1.11 1.06 1.01 1.00 0.96 0.91 0.87 0.86

S10 0.02 OVER 200 HP 1.11 1.06 1.02 1.00 0.96 0.91 0.87 0.86 0.85 0.84

S15 0.00 SCRAPERS, CONVENTIONAL 1.11 1.06 1.01 1.00 0.96 0.91 0.88 0.87 0.85 0.85 0.83 0.80

S20 0.00 SCRAPERS, TANDEM POWERED 1.11 1.06 1.01 1.00 0.96 0.91 0.88 0.87 0.85 0.85 0.83 0.80

S25 0.00 SCRAPERS, TRACTOR DRAWN 1.11 1.06 1.01 1.00 0.96 0.91 0.88 0.86 0.85

S30 0.00 SCREENING & CRUSHING PLANTS

S30 0.10 CONVEYORS 1.11 1.06 1.03 1.00 0.96 0.89 0.86 0.85

S30 0.20 CRUSHERS - VERTICAL & HORIZONTAL SHAFT IMPACTOR 1.11 1.06 1.03 1.00 0.96 0.90 0.87 0.85 0.84 0.84 0.83 0.82 0.80 0.79 0.77 0.75 0.74 0.72

S30 0.21 CRUSHERS - CONE 1.11 1.06 1.03 1.00 0.96 0.90 0.87 0.85 0.84 0.84 0.83 0.82 0.80 0.79 0.77 0.75 0.74 0.72

S30 0.22 CRUSHERS - JAW 1.11 1.06 1.03 1.00 0.96 0.90 0.87 0.85 0.84 0.84 0.83 0.82 0.80 0.79 0.77 0.75 0.74 0.72

S30 0.30 SCREENING PLANT 1.11 1.06 1.03 1.00 0.96 0.89 0.86 0.85

3- 18

EP 1110-1-8, Vol. 130 Nov 09

3-19


CATEGORY


REGION 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

7/31/2009(Vol. 1)

S35 0.00 SNOW REMOVAL EQUIPMENT 1.12 1.07 1.03 1.00 0.95 0.88

S40 0.00 SOIL & ROAD STABILIZERS 1.11 1.06 1.01 1.00 0.96 0.91 0.87 0.86

S45 0.00 SPLITTERS, ROCK & CONCRETE 1.13 1.07 1.03 1.00 0.95

T10 0.00 TRACTOR BLADES & ATTACHMENTS (including agricultural) 1.13 1.06 1.02 1.00 0.96 0.90 0.87 0.86

T15 0.00 TRACTORS, CRAWLER (DOZER) (includes blade)

T15 0.01 0 THRU 225 HP 1.14 1.07 1.03 1.00 0.95 0.89 0.86 0.84

T15 0.02 226 HP THRU 425 HP 1.13 1.06 1.02 1.00 0.95 0.90 0.87 0.85 0.85 0.84

T15 0.03 OVER 425 HP 1.12 1.06 1.02 1.00 0.96 0.90 0.88 0.86 0.86 0.85 0.84 0.81

T20 0.00 TRACTORS, WHEEL TYPE (DOZER) 1.17 1.11 1.05 1.00 0.95 0.91 0.86 0.84 0.83 0.81 0.80

T25 0.00 TRACTORS, AGRICULTURAL

T25 0.10 CRAWLER 1.17 1.11 1.05 1.00 0.95 0.91 0.86 0.84

T25 0.20 WHEEL 1.17 1.11 1.05 1.00 0.95 0.91

T30 0.00 TRENCHERS, CHAIN TYPE CUTTER 1.18 1.12 1.06 1.00 0.95 0.90

T35 0.00 TRENCHERS, WHEEL TYPE CUTTER 1.18 1.12 1.06 1.00 0.95 0.90

T40 0.00 TRUCK OPTIONS

T40 0.10 CRANES / HOISTS, PERSONNEL & MATERIAL HANDLING 1.12 1.07 1.03 1.00 0.95 0.88

T40 0.20 DUMP BODY, REAR 1.11 1.06 1.03 1.00 0.96 0.89

T40 0.30 FLATBEDS, WITH SIDES 1.12 1.07 1.03 1.00 0.95 0.88

T40 0.41 HOIST, ELECTRIC DRIVE 1.12 1.07 1.03 1.00 0.95 0.88

T40 0.50 TRANSIT MIXERS 1.12 1.07 1.03 1.00 0.95 0.89

T40 0.60 WATER TANKS 1.13 1.07 1.03 1.00 0.95 0.87

T40 0.70 ALL OTHER OPTIONS 1.12 1.07 1.03 1.00 0.95 0.88

3- 19

EP 1110-1-8, Vol. 130 Nov 09

3-20


CATEGORY


REGION 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

7/31/2009(Vol. 1)

T45 0.00 TRUCK TRAILERS

T45 0.10 BOTTOM DUMP 1.11 1.06 1.03 1.00 0.96 0.89 0.86 0.85

T45 0.20 END DUMP 1.11 1.06 1.03 1.00 0.96 0.89 0.86 0.85

T45 0.30 PUP TRAILER 1.11 1.06 1.03 1.00 0.96 0.89

T45 0.41 LOWBOY, RIGID NECK, DROP DECK 1.11 1.06 1.03 1.00 0.96 0.89 0.86 0.85

T45 0.50 FLATBED TRAILER 1.11 1.06 1.03 1.00 0.96 0.89 0.86 0.85

T45 0.60 MISCELLANEOUS / UTILITY 1.11 1.06 1.03 1.00 0.96 0.89 0.86 0.85

T45 0.70 WATER TANKER TRAILER 1.13 1.07 1.03 1.00 0.95 0.88 0.84 0.82

T45 0.80 DECONTAMINATION FACILITY 1.13 1.07 1.03 1.00 0.95 0.87

T45 0.90 TANK TRAILERS 1.13 1.07 1.03 1.00 0.95 0.88 0.84 0.82

T50 0.00 TRUCKS, HIGHWAY (Add attachments as required)

T50 0.01 0 THRU 10,000 GVW 1.13 1.08 1.04 1.00 0.95 0.91

T50 0.02 OVER 10,000 THRU 30,000 GVW (Chassis only - Add options) 1.13 1.08 1.04 1.00 0.95 0.91 0.88 0.87

T50 0.03 OVER 30,000 GVW (Chassis only - Add options) 1.13 1.07 1.04 1.00 0.95 0.91 0.88 0.87 0.85

T55 0.00 TRUCKS, OFF-HIGHWAY

T55 0.10 RIGID FRAME 1.09 1.06 1.02 1.00 0.95 0.88 0.83 0.82 0.80 0.79 0.77 0.76 0.75 0.73 0.70

T55 0.20 ARTICULATED FRAME 1.10 1.07 1.03 1.00 0.95 0.87 0.82 0.81 0.80 0.78

T56 0.00 TRUCKS,OFF-HIGHWAY/PRIME MOVER TRACTORS & WAGONS

T56 0.10 PRIME MOVER TRACTORS 1.09 1.06 1.02 1.00 0.95 0.88 0.83 0.82 0.80 0.79 0.77 0.76 0.75 0.73 0.70

T56 0.20 WAGONS, BOTTOM DUMP 1.10 1.07 1.03 1.00 0.95 0.87 0.82 0.80 0.79 0.77 0.75 0.74

T56 0.30 WAGONS, REAR DUMP 1.10 1.07 1.03 1.00 0.94 0.87 0.81 0.80 0.79

T57 0.00 TRUCKS, VACUUM 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83

3- 20

EP 1110-1-8, Vol. 130 Nov 09

3-21


CATEGORY


REGION 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

7/31/2009(Vol. 1)

T60 0.00 TRUCKS, WATER, OFF-HIGHWAY 1.10 1.07 1.03 1.00 0.94 0.87 0.81 0.80 0.79

T65 0.00 TUNNEL/MINING EQUIPMENT

T65 0.10 DRIFTING & TUNNELING DRILLS 1.20 1.15 1.08 1.00 0.92 0.85 0.80 0.78 0.71 0.69 0.68

T65 0.20 TUNNEL BORING MACHINES 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.85 0.83 0.83 0.82 0.81 0.79 0.77

T65 0.30 PRODUCTION DRILLING RIGS 1.21 1.15 1.08 1.00 0.92 0.85 0.79 0.78 0.71

T65 0.40 ROADHEADERS & CONTINUOUS MINERS 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.84 0.83 0.83 0.82 0.81

T65 0.50 ROCK BOLTING EQUIPMENT 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83

T65 0.61 LOADING & HAULING EQUIPMENT, DIESEL OR GAS 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82

T65 0.62 LOADING & HAULING EQUIPMENT, ELECTRIC 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81

T65 0.63 LOADING & HAULING EQUIPMENT, AIR-POWERED 1.13 1.07 1.03 1.00 0.95 0.88 0.84 0.82

T65 0.70 LOCOMOTIVES 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82

T65 0.90 OTHER TUNNELING EQUIPMENT 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83

W10 0.00 WAGONS, BOTTOM DUMP 1.10 1.07 1.03 1.00 0.95 0.87 0.82 0.81 0.80

W15 0.00 WAGONS, REAR DUMP 1.10 1.07 1.03 1.00 0.95 0.87 0.82 0.81 0.80

W25 0.00 WATER & CO2 BLASTERS

W25 0.10 LOW PRESSURE, (< 5,000 PSI) 1.13 1.07 1.03 1.00

W25 0.20 HIGH PRESSURE, (>= 5,000 PSI) 1.13 1.07 1.03 1.00

W25 0.30 STEAM CLEANERS 1.13 1.07 1.03 1.00

W25 0.40 CO2 BLASTERS 1.13 1.07 1.03 1.00 0.95

W25 0.50 WET ABRASIVE BLASTING SYSTEM (TORBO) 1.15 1.08 1.03 1.00 0.94 0.86 0.82 0.80

W30 0.00 WATER TANKS

W30 0.10 PORTABLE WITH WHEELS 1.10 1.07 1.03 1.00 0.94 0.87 0.81 0.80 0.79

3- 21

EP 1110-1-8, Vol. 130 Nov 09

3-22


CATEGORY


REGION 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

EP 1110-1-8

7/31/2009(Vol. 1)

W30 0.20 SKID MOUNTED 1.10 1.07 1.03 1.00 0.94 0.87 0.81 0.80 0.79

W35 0.00 WELDERS

W35 0.10 ENGINE DRIVEN 1.13 1.07 1.03 1.00 0.95 0.87

W35 0.20 ELECTRIC DRIVEN 1.13 1.07 1.03 1.00 0.95

3- 22

EP 1110-1-8, Vol. 130 Nov 09

3-23


EP 1110-1-8, Vol. 130 Nov 09

3-24

1. The unit of equipment is not listed in table 2-1.

2. The equipment is contractor owned.

3. Data for the unit in question:

a. Caterpillar front-end wheel loaderb.c. Serial number indicates year of manufacture = 1997d. 1997 = $195,628

e. Horsepower is 170 hp (fuel is Diesel off-road)f.

= x $2,053 /tire = $8,212g.

4. Table 3-1, Age Adjustment Factors for Ownership Costs:

a. The category L40, subcategory 0.11 (wheel loaders < 225 hp)b. = 2003

5.

a. Economic Indexes from appendix E (wheel loaders EK = 45)(1) = 5701(2) = 5303

b.

(5701 / 5303) x = $210,310 (= 2003 purchase price)

6.

TOTAL HOURLY RATE CALCULATION FOR OVERAGE EQUIPMENT

EXAMPLE

The year corresponding to the last age adjustment factor

Drive tire (DT) size = 23.50 x 25, 16 ply, L-3 (appendix F tire code ANNB5)

Actual purchase price in

DT cost (2009)351 cwt

Model 950-F11, 4WD, 3.25 CY capacity

Hourly rate is computed as follows in accordance with figure 2-1, Equipment Rate Computation Worksheet.

Assume the following set of given information for the rate calculation example:

For 2003 (first year of economic life), the economic indexFor 1997 (year of manufacture), the economic index

Adjust the actual purchase price:

$195,628

4 tires

(includes all regional discounts, sales tax and freight)

Purchase price [total equipment value (TEV)] indexed to 2003 (first year of economic life): (Purchase price includes discount, sales tax, and freight for this region).

Weight =

Figure 3-1. Total Hourly Rate Calculation for Overage Equipment

EP 1110-1-8, Vol. 130 Nov 09

3-25

1.

a.(1)(2)(3) 2009(4) 2003(5) 170(6) 0(7)

3 D-off

0 None(8) 351 cwt

(9)

Size/Ply App F Code No. Unit Price Cost(a) Front (FT): 0 $0 $0(b) Drive (DT): 23.5X25/16Ply ANNB5 4 $2,053 $8,212(c) 0 $0 $0

(d) $8,212(10)

$0 $210,310

b. 0.11c.

(1) 45(2) A AVERAGE(3) B 0.075(4) 9,250(5) 0.25(6) 0.031(7) 0.000(8) 0.111(9)

(a) 0.83(b) 0.54(c) 0.92

(10) 0.70

Equipment Specification Data:Equipment Description: Model and Series:


Fuel


Front (FT):






Enter number from 0 to 6 ==>

L40Category and Subcategory Number:

Tire size and number of tires: (Cost of tires based on present year - see 1.a.(3) and Appendix F)



Drive (DT):



Total Tire Cost:

USE APPENDIX D TO COMPLETE THE FOLLOWING DATA:

Trailing (TT):





USE THIS WORKSHEET TO COMPUTE A HOURLY RATE FOR EQUIPMENT THAT IS NOT IN THIS PAMPHLET OR IS IN THE PAMPHLET BUT NOT EQUIVALENT IN SIZE, CAPACITY, HORSEPOWER OR VALUE. (See Appendix A for a blank

form)Region 01

ID No:


EQUIPMENT INFORMATION AND EXPENSE FACTORS

Loader, Front-end, Wheel, 4WD, 4 CY capacityCaterpillar Model 950-F11


1997 indexed to

Tire Wear Factor:Filter, Oil, and Grease (FOG) Factor (E G D):

Economic Key (EK):

Trailing (TT):

Figure 3-1. Total Hourly Rate Calculation for Overage Equipment Page 1 of 6

EP 1110-1-8, Vol. 130 Nov 09

3-26

2.

a. = $0

(1) Discount: (List Price + Accessories) x Discount Code

{1.a.(10)} {1.c.(3)}($0 + $0.00) x 0.075 = $0

(2) Subtotal = $0

(3) Sales or Import Tax:

Subtotal x Tax Rate

{2.a.(2)} {Appendix B}

$0 x 6.00% = $0

(4) Subtotal = $0

b. Shipping Weight x Freight Rate

per cwt{1.a.(8)}

0,000 cwt x $0.00 /cwt = $0

c. TOTAL[2.]: = $210,310

3.

a. LIFE / Working Hours Per Year (WHPY) = N

{1.c.(4)} {Appendix B}

9,250 hr / 1,360 hr/yr = 6.80 yrs (N)

4.

a.(1)


{1.a.(4)} /

Tire Index, Present Year or Year of Use, {1.a.(3)} = TCI

Appendix E, EK=100 Appendix E, EK=100

2487 / 3382 = 0.735


[$210,310 x (1.0-0.25) - ( 0.735 x $8,212 )] / 9,250 hr = $16.40 /hr

{Appendix B}

Region 01

EQUIPMENT VALUE


Total Discounted Price: Subtotal: {2.a.(2)} + {2.a.(3)}


OWNERSHIP COST

Subtotal {2.a}. - {2.a.(1)}

Tire Cost Index (TCI):

Freight:


Depreciation

(See chapter 3 for used and overage equipment rate adjustments.) {2.a.(4)} + {2.b} OR actual purchase price {1a.(10)}


EP 1110-1-8, Vol. 130 Nov 09

3-27

4. OWNERSHIP COST (Continued)

b. Facilities Capital Cost of Money (FCCM):

(1) [( N - 1.0 ) x (1.0 + SLV) + 2.0] / (2.0 x N) =Avg Value

Factor{3.a.} {1.c.5.} {3.a.} {AVF}

[(6.80 yr - 1.0) x (1.0 + 0.25) + 2.0] / (2.0 x 6.80 yr) = 0.680




$210,310 x 0.680 x 3.90% / 1,360 hr/yr = $4.10 /hr

c. TOTAL HOURLY OWNERSHIP COST: TOTAL [4.]: = $20.50 /hr

{4.a.(2)} + {4.b.(2)}

5. OPERATING COST

a. Fuel Costs:

(1) Equipment:

Fuel Factor x Horsepower (hp) xFuel Cost per Gallon (gal)

{1.c.(6)} {1.a.(5)} {Appendix B}

0.031 x 170 hp x $3.17 /gal = $16.71 /hr

(2) Carrier:

Fuel Factor x hp x Fuel Cost per gal{1.c.(7)} {1.a.(6)} {Appendix B}

0.000 x 0 hp x $0.00 /gal = $0.00 /hr

(3) Total Hourly Fuel Cost: Total [5.a.] = $16.71 /hr{(5.a (1)} + {5.a (2)}

b. FOG Cost:

(1) Equipment:

FOG Factor xEquipment Hourly

Fuel Cost xLabor Adjustment

Factor (LAF){1.c.(8)} {5.a.(1)} {Appendix B}0.111 x $16.71 /hr x $ 1.12 /hr = $2.08 /hr

Region 01


EP 1110-1-8, Vol. 130 Nov 09

3-28

5.

(2) Carrier:



0.111 x $0.00 /hr x 1.12 = $0.00 /hr

(3) = $2.08 /hr{5.b.(1)} + {5.b.(2)}

c. = $0.00 hr

d.

(1)[EK is from 1c. (1)]

Economic Index, Present Year or Year

of Use,1.a.(3)

/ Economic Index, Year of Manufacture, 1.a.(4)

= EAFAppendix E, EK={1.c.(1)} Appendix E, EK={1.c.(1)}

7047 / 5701 = 1.236


RCF x EAF x LAF= RF

{1.c.(10)} {5.d.(1)} {Appendix B}

0.70 x 1.236 x 1.12 = 0.969

(3) Repair Cost:


[$210,310 - (0.735 x $8,212)] x 0.969 / 9,250

(4) = $21.40 /hr


Repair Cost:

Economic Adjustment Factor (EAF):

Total Hourly Repair Cost: Total [5.d.]

Alternative Fuel/FOG Cost: Total [5.c.](See chapter 2, paragraph 2.24.d. for guidance on when to use.)

Region 01

Total [5.b.]Total Hourly FOG Cost:



EP 1110-1-8, Vol. 130 Nov 09

3-29

5.

e.



(1.5 x $0) / (1.8 x 0.83 x 0 hr) = $0.00 /hr



(1.5 x $8,212) / (1.8 x 0.54 x 3200 hr) = $3.96 /hr



(1.5 x $0) / (1.8 x 0.92 x 0 hr) = $0.00 /hr

(4) Total Tire Wear Cost: Total [5.e.] = $3.96 /hr

f.



$3.96 /hr x (0.15 x 1.12) Total [5.f.] = $0.67 /hr

g. Total [5.] = $44.82 /hrTOTAL HOURLY OPERATING COST:Sum {5.a.} through {5.f.}

Sum {5.e.(1)} through {5.e.(3)}

Region 01


Tire Wear Cost: (Use current price levels. See Appendix F.)

Tire Repair Cost:


EP 1110-1-8, Vol. 130 Nov 09

3-30

6. HOURLY RATES

a. Total Hourly Rate: [based on 40 hours per week (wk)]

Ownership Cost +{4.c.} {5.g.}

$20.50 /hr + $44.82 /hr = $65.32 /hr

b.



{4.a.(2)} {4.b.(2)} {5.g.}

$0.00 /hr + ($0.00 /hr x 40 hr/wk / 60 hr/wk) + $0.00 /hr = $0.00 /hr

c.



($0.00 /hr x 0.50) + $0.00 /hr = $0.00 /hr


See Figure 3-2 for standby calculations for overage equipment



Region 01


example:60 hr/wk

(example:60 hr/wk)

Operating Cost


EP 1110-1-8, Vol. 130 Nov 09

3-31


EP 1110-1-8, Vol. 130 Nov 09

3-32

Table 3-2. Equipment Age Adjustment Factors

for

Standby costs

The factors in this table are used when the age of a unit of equipment is other than the age of the equipment listed in table 2-1.

These factors are multiplied by the hourly standby costs shown in table 2-1 and result in a standby rate adjusted for the actual age of the equipment being considered.

When the actual “life” in hours of the unit of equipment has exceeded the economic life given in appendix D, the age will be determined as discussed in chapter 3.

Refer to chapter 3, as follows:

3-13. Rate Adjustments Overage Equipment Standby

3-39

EP 1110-1-8, Vol. 130 Nov 09

3-33

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Table 3-2 Equipment Age Adjustment Factors for Standby CostYear Purchased New

CATEGORY


REGION 1 Life in Years

EP 1110-1-8

7/31/2009(Vol. 1)

A10 0.00 AGGREGATE / CHIP SPREADERS

A10 0.10 SELF-PROPELLED 1.13 1.08 1.03 1.00 0.95 0.90 0.90 0.90 0.90 0.89 0.86 0.85 0.82 0.79 0.77 0.75 0.74 0.71

A10 0.20 TOWED & TAILGATE 1.13 1.08 1.03 1.00 0.95 0.90 0.90 0.90 0.90 0.88 0.86 0.85 0.82 0.79 0.77 0.75 0.73 0.70

A15 0.00 AIR COMPRESSORS, PORTABLE

A15 0.10 ROTARY SCREW 1.19 1.12 1.04 1.00 0.96 0.92 0.92 0.91 0.92 0.90 0.92 0.92 0.91 0.91 0.91 0.88 0.89 0.88

A15 0.20 SHOP TYPE 1.18 1.11 1.04 1.00 0.96 0.93 0.92 0.92 0.92 0.91 0.92 0.92 0.92 0.92 0.91 0.89 0.90 0.89

A20 0.00 AIR HOSE, TOOLS & EQUIPMENT

A20 0.10 AIR DRILL HOSE 1.17 1.11 1.04 1.00 0.96 0.93 0.93 0.92 0.93 0.91 0.93 0.92 0.92 0.92 0.91 0.90 0.90 0.89

A20 0.20 SANDBLAST HOSE 1.17 1.11 1.04 1.00 0.96 0.93 0.93 0.92 0.93 0.91 0.93 0.92 0.92 0.92 0.91 0.90 0.90 0.89

A20 0.30 SANDBLASTERS, BREAKERS, & MISC. AIR TOOLS 1.18 1.11 1.04 1.00 0.96 0.93 0.92 0.92 0.92 0.91 0.92 0.92 0.92 0.92 0.91 0.89 0.90 0.89

A25 0.00 ASPHALT PAVING DISTRIBUTORS 1.12 1.07 1.03 1.00 0.96 0.91 0.91 0.91 0.91 0.89 0.87 0.86 0.83 0.81 0.79 0.77 0.75 0.73

A30 0.00 ASPHALT PAVERS & MISCELLANEOUS ROAD EQUIPMENT

A30 0.10 SELF PROPELLED 1.12 1.07 1.03 1.00 0.95 0.90 0.90 0.91 0.90 0.89 0.87 0.86 0.83 0.80 0.78 0.76 0.75 0.72

A30 0.20 TOWED 1.12 1.07 1.03 1.00 0.95 0.90 0.90 0.90 0.90 0.89 0.87 0.85 0.83 0.80 0.78 0.76 0.74 0.71

A30 0.30 SLURRY SEAL PAVERS (Cold mix) 1.12 1.07 1.03 1.00 0.95 0.90 0.90 0.90 0.90 0.89 0.87 0.86 0.83 0.80 0.78 0.76 0.75 0.72

A30 0.40 MISCELLANEOUS ROAD EQUIPMENT 1.12 1.07 1.03 1.00 0.95 0.90 0.90 0.90 0.90 0.89 0.87 0.85 0.83 0.80 0.78 0.76 0.74 0.71

A35 0.00 ASPHALT PAVING KETTLES 1.13 1.08 1.03 1.00 0.95 0.90 0.90 0.90 0.90 0.88 0.86 0.85 0.82 0.79 0.77 0.75 0.73 0.70

A40 0.00 ASPHALT & CONCRETE MILLERS / PROFILERS / PLANERS / ROTARY GRINDERS

1.13 1.08 1.03 1.00 0.95 0.90 0.90 0.90 0.90 0.88 0.86 0.85 0.82 0.79 0.77 0.75 0.73 0.70

A45 0.00 ASPHALT RECYCLERS & SEALERS 1.13 1.08 1.03 1.00 0.95 0.89 0.90 0.90 0.90 0.88 0.86 0.85 0.82 0.79 0.77 0.74 0.73 0.70

B10 0.00 BATCH PLANTS, ASPHALT & CONCRETE

B10 0.10 ASPHALT 1.13 1.08 1.03 1.00 0.95 0.90 0.90 0.90 0.90 0.89 0.86 0.85 0.82 0.79 0.77 0.75 0.74 0.71

B10 0.20 CONCRETE 1.13 1.08 1.03 1.00 0.95 0.90 0.90 0.90 0.90 0.89 0.86 0.85 0.82 0.79 0.77 0.75 0.74 0.71

3- 28

EP 1110-1-8, Vol. 130 Nov 09

3-34

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

7/31/2009(Vol. 1)

B10 0.30 PUGMILL 1.12 1.07 1.03 1.00 0.95 0.90 0.90 0.90 0.90 0.89 0.87 0.85 0.83 0.80 0.78 0.76 0.74 0.71

B15 0.00 BROOMS, STREET SWEEPERS & FLUSHERS 1.11 1.06 1.03 1.00 0.96 0.90 0.86 0.85 0.84 0.84 0.83 0.81 0.80 0.78 0.76 0.74 0.73 0.71

B20 0.00 BRUSH CHIPPERS 1.11 1.06 1.03 1.00 0.96 0.90 0.86 0.85 0.84 0.84 0.83 0.81 0.80 0.78 0.76 0.74 0.73 0.71

B25 0.00 BUCKETS, CLAMSHELL 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.79 0.80 0.81 0.80 0.80 0.78 0.77 0.76 0.77 0.73

B30 0.00 BUCKETS, CONCRETE

B30 0.10 GENERAL PURPOSE, MANUAL TRIP 1.06 1.02 1.01 1.00 0.95 0.89 0.87 0.85 0.79 0.80 0.81 0.81 0.80 0.79 0.78 0.77 0.78 0.74

B30 0.20 LAYDOWN 1.06 1.02 1.01 1.00 0.95 0.89 0.87 0.85 0.79 0.80 0.81 0.81 0.80 0.79 0.78 0.77 0.78 0.74

B30 0.30 LOWBOY 1.06 1.02 1.01 1.00 0.95 0.89 0.87 0.85 0.79 0.80 0.81 0.81 0.80 0.79 0.78 0.77 0.78 0.74

B30 0.40 LOW SLUMP 1.06 1.02 1.01 1.00 0.95 0.89 0.87 0.85 0.79 0.80 0.81 0.81 0.80 0.79 0.78 0.77 0.78 0.74

B35 0.00 BUCKETS, DRAGLINE

B35 0.10 LIGHT WEIGHT 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.79 0.80 0.81 0.80 0.80 0.78 0.77 0.76 0.77 0.73

B35 0.20 MEDIUM WEIGHT 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.79 0.80 0.81 0.80 0.80 0.78 0.77 0.77 0.77 0.73

B35 0.30 HEAVY WEIGHT 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.79 0.80 0.81 0.80 0.80 0.78 0.77 0.77 0.77 0.73

C05 0.00 CHAIN SAWS 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.85 0.83 0.83 0.82 0.81 0.79 0.77 0.75 0.73 0.72 0.70

C10 0.00 COMPACTORS, WALK-BEHIND OR REMOTE CONTROLLER

C10 0.10 COMPACTORS, RAMMERS / TAMPERS & VIBRATORY PLATES 1.11 1.06 1.02 1.00 0.96 0.90 0.87 0.85 0.84 0.84 0.83 0.82 0.80 0.79 0.77 0.75 0.74 0.72

C10 0.20 ROLLERS, VIBRATORY 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.83 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

C15 0.00 CONCRETE CLEANERS / ABRASIVE BLASTERS

C15 0.10 WALK BEHIND 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.81 0.80 0.79 0.77 0.75 0.73 0.71 0.70 0.67

C15 0.20 TRUCK/TRAILER MOUNTED 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

C20 0.00 CONCRETE BUGGIES 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.81 0.80 0.79 0.77 0.75 0.73 0.71 0.70 0.67

C25 0.00 CONCRETE FINISHERS/SCREEDS/SPREADERS

3- 29

EP 1110-1-8, Vol. 130 Nov 09

3-35

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

7/31/2009(Vol. 1)

C25 0.10 FINISHERS/TROWELS 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.75 0.73 0.71 0.70 0.68

C25 0.20 VIBRATORY SCREED 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.75 0.73 0.71 0.70 0.68

C25 0.25 VIBRATORY LASER SCREED 1.13 1.07 1.03 1.00 0.95 0.88 0.84 0.82 0.81 0.80 0.79 0.78 0.76 0.74 0.72 0.70 0.68 0.66

C25 0.30 MATERIAL/TOPPING SPREADERS 1.13 1.07 1.03 1.00 0.95 0.88 0.84 0.82 0.81 0.80 0.79 0.78 0.76 0.74 0.72 0.70 0.68 0.66

C30 0.00 CONCRETE GRINDERS 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.75 0.73 0.71 0.70 0.68

C35 0.00 CONCRETE GUNITERS / SHOTCRETERS 1.13 1.07 1.03 1.00 0.95 0.88 0.84 0.83 0.81 0.81 0.80 0.79 0.77 0.75 0.73 0.71 0.69 0.67

C40 0.00 CONCRETE MIXING UNITS 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.75 0.73 0.71 0.70 0.68

C45 0.00 CONCRETE PAVING MACHINES 1.13 1.08 1.03 1.00 0.95 0.90 0.90 0.90 0.90 0.88 0.86 0.85 0.82 0.79 0.77 0.75 0.73 0.70

C55 0.00 CONCRETE PUMPS 1.11 1.06 1.03 1.00 0.96 0.90 0.86 0.85 0.84 0.84 0.83 0.81 0.80 0.78 0.76 0.74 0.73 0.71

C60 0.00 CONCRETE SAWS (Add cost for sawblade wear) 1.11 1.06 1.03 1.00 0.96 0.89 0.86 0.85 0.84 0.83 0.82 0.81 0.79 0.78 0.76 0.74 0.73 0.71

C65 0.00 CONCRETE VIBRATORS 1.18 1.11 1.04 1.00 0.96 0.93 0.92 0.92 0.92 0.91 0.92 0.92 0.92 0.92 0.91 0.89 0.89 0.89

C70 0.00 CRANES, GANTRY & STRADDLE

C75 0.00 CRANES, HYDRAULIC, SELF-PROPELLED 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.78 0.80 0.79 0.78 0.76 0.75 0.73 0.71 0.70 0.67

C80 0.00 CRANES, HYDRAULIC, TRUCK MOUNTED

C80 0.01 UNDER 26 TON 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.78 0.80 0.79 0.78 0.76 0.75 0.73 0.71 0.70 0.67

C80 0.02 26 TON THRU 65 TON 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.79 0.80 0.80 0.78 0.77 0.75 0.73 0.71 0.71 0.67

C80 0.03 66 TON THRU 125 TON 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.79 0.80 0.80 0.79 0.77 0.75 0.73 0.72 0.71 0.68

C80 0.04 OVER 125 TON 1.06 1.02 1.01 1.00 0.95 0.89 0.87 0.85 0.79 0.80 0.80 0.79 0.77 0.75 0.73 0.72 0.71 0.68

C85 0.00 CRANES, MECHANICAL, LATTICE BOOM, CRAWLER MOUNTED

C85 0.11 DRAGLINE, CLAMSHELL, 0 THRU 1.0 CY 1.06 1.02 1.01 1.00 0.94 0.89 0.86 0.84 0.78 0.79 0.79 0.78 0.76 0.74 0.72 0.70 0.69 0.66

C85 0.12 DRAGLINE, CLAMSHELL, OVER 1.0 CY THRU 2.5 CY 1.06 1.02 1.01 1.00 0.94 0.89 0.86 0.84 0.78 0.79 0.79 0.78 0.76 0.74 0.72 0.71 0.70 0.67

C85 0.13 DRAGLINE, CLAMSHELL, OVER 2.5 CY THRU 5.0 CY 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.78 0.80 0.79 0.78 0.76 0.75 0.73 0.71 0.70 0.67

3- 30

EP 1110-1-8, Vol. 130 Nov 09

3-36

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

7/31/2009(Vol. 1)

C85 0.14 DRAGLINE, CLAMSHELL, OVER 5.0 CY 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.79 0.80 0.80 0.79 0.77 0.75 0.73 0.71 0.71 0.67

C85 0.21 LIFTING, 0 THRU 25 TON 1.06 1.02 1.01 1.00 0.94 0.89 0.86 0.84 0.78 0.79 0.79 0.78 0.76 0.74 0.72 0.71 0.70 0.67

C85 0.22 LIFTING, 26 TON THRU 50 TON 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.78 0.80 0.79 0.78 0.76 0.75 0.73 0.71 0.70 0.67

C85 0.23 LIFTING, 51 TON THRU 150 TON 1.06 1.02 1.01 1.00 0.95 0.89 0.87 0.85 0.79 0.80 0.80 0.79 0.77 0.75 0.73 0.72 0.71 0.68

C85 0.24 LIFTING, OVER 150 TON 1.06 1.02 1.01 1.00 0.95 0.89 0.87 0.85 0.79 0.80 0.80 0.79 0.77 0.76 0.74 0.72 0.71 0.68

C90 0.00 CRANES, MECHANICAL, LATTICE BOOM, TRUCK MOUNTED

C90 0.01 UNDER 26 TON 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.78 0.80 0.79 0.78 0.76 0.75 0.73 0.71 0.70 0.67

C90 0.02 26 TON THRU 65 TON 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.79 0.80 0.80 0.78 0.77 0.75 0.73 0.71 0.71 0.67

C90 0.03 66 TON THRU 125 TON 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.78 0.80 0.79 0.78 0.76 0.75 0.73 0.71 0.70 0.67

C90 0.04 OVER 125 TON 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.79 0.80 0.80 0.79 0.77 0.75 0.73 0.71 0.71 0.67

C95 0.00 CRANES, TOWER 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.78 0.80 0.79 0.78 0.76 0.75 0.73 0.71 0.70 0.67

D10 0.00 DRILLS, AIR/HYDRAULIC,CRWLR MTD,0" THRU 6.5" DIA HOLE (Add cost for drill steel and bit wear)

D10 0.10 DRILLS, AIR TRACK (Add cost for drill steel and bit wear) 1.21 1.15 1.08 1.00 0.92 0.85 0.79 0.78 0.71 0.69 0.68 0.67 0.65 0.64 0.61 0.60 0.58 0.57

D10 0.20 DRILLS, HYDRAULIC TRACK (Add cost for drill steel and bit wear) 1.22 1.16 1.08 1.00 0.92 0.84 0.78 0.77 0.70 0.68 0.66 0.65 0.64 0.62 0.60 0.58 0.57 0.55

D15 0.00 DRILLS, HORIZONTAL BORING & GROUND PIERCING (Add cost for drill steel and bit wear)

1.22 1.16 1.08 1.00 0.92 0.84 0.78 0.77 0.70 0.68 0.66 0.65 0.64 0.62 0.60 0.58 0.57 0.55

D20 0.00 DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit wear) 1.22 1.17 1.08 1.00 0.92 0.84 0.78 0.76 0.69 0.67 0.65 0.64 0.63 0.61 0.58 0.57 0.55 0.54

D25 0.00 DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear) 1.22 1.16 1.08 1.00 0.92 0.84 0.78 0.77 0.70 0.68 0.66 0.65 0.64 0.62 0.60 0.58 0.57 0.55

D30 0.00 DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear) 1.22 1.16 1.08 1.00 0.92 0.84 0.78 0.77 0.70 0.68 0.66 0.65 0.64 0.62 0.60 0.58 0.57 0.55

D35 0.00 DRILLS, ROTARY BLASTHOLE (Add cost for drill steel and bit wear)

D35 0.11 DIESEL, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit wear)

1.20 1.15 1.08 1.00 0.92 0.86 0.80 0.78 0.72 0.70 0.69 0.68 0.66 0.65 0.62 0.61 0.60 0.58

D35 0.12 DIESEL, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear) 1.19 1.14 1.07 1.00 0.93 0.86 0.81 0.79 0.73 0.71 0.70 0.68 0.67 0.66 0.64 0.62 0.61 0.59

D35 0.21 ELECTRIC, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit wear)

1.20 1.15 1.08 1.00 0.92 0.86 0.80 0.78 0.72 0.70 0.69 0.68 0.66 0.65 0.62 0.61 0.60 0.58

3- 31

EP 1110-1-8, Vol. 130 Nov 09

3-37

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

7/31/2009(Vol. 1)

D35 0.22 ELECTRIC, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear) 1.19 1.14 1.07 1.00 0.93 0.86 0.81 0.79 0.73 0.71 0.70 0.68 0.67 0.66 0.64 0.62 0.61 0.59

F10 0.00 FORK LIFTS 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.83 0.82 0.82 0.80 0.78 0.77 0.75 0.73 0.72 0.69

G10 0.00 GENERATOR SETS

G10 0.10 PORTABLE 1.15 1.11 1.05 1.00 0.95 0.90 0.88 0.88 0.88 0.88 0.87 0.87 0.87 0.87 0.86 0.84 0.83 0.81

G10 0.20 SKID MOUNTED 1.15 1.11 1.05 1.00 0.95 0.90 0.89 0.88 0.88 0.88 0.88 0.88 0.87 0.87 0.86 0.84 0.83 0.82

G15 0.00 GRADERS, MOTOR 1.10 1.05 1.01 1.00 0.96 0.92 0.88 0.87 0.86 0.85 0.84 0.81 0.79 0.77 0.73 0.71 0.69 0.64

H10 0.00 HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear) 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.76 0.74 0.72 0.70 0.68

H13 0.00 HAZARDOUS/TOXIC WASTE EQUIPMENT

H13 0.11 COMPACTORS (Compression force) 0 THRU 50 TONS 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.85 0.83 0.83 0.82 0.81 0.79 0.78 0.76 0.74 0.73 0.71

H13 0.12 COMPACTORS (Compression force) OVER 50 TONS 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.84 0.83 0.83 0.82 0.81 0.79 0.77 0.75 0.73 0.72 0.70

H13 0.21 FILTER PRESSES, STATIONARY 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.83 0.82 0.82 0.80 0.78 0.77 0.75 0.73 0.72 0.69

H13 0.22 FILTER PRESSES, MOBILE 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.85 0.83 0.83 0.82 0.81 0.79 0.78 0.76 0.74 0.73 0.71

H13 0.30 CENTRIFUGES 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.81 0.80 0.79 0.77 0.75 0.73 0.71 0.70 0.67

H13 0.40 SHREDDERS 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.85 0.83 0.83 0.82 0.81 0.79 0.78 0.76 0.74 0.73 0.71

H13 0.51 SOIL TREATMENT PLANT, MOBILE 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.85 0.83 0.83 0.82 0.81 0.79 0.78 0.76 0.74 0.73 0.71

H13 0.61 SLUDGE PROCESSING EQUIP, SLUDGE DISPENSERS 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.85 0.83 0.83 0.82 0.81 0.79 0.78 0.76 0.74 0.73 0.71

H13 0.71 WASTE HANDLING EQUIPMENT, DRUM HANDLING 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.83 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

H15 0.00 HEATERS, SPACE

H20 0.00 HOISTS & AIR WINCHES 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.83 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

H25 0.00 HYDRAULIC EXCAVATORS, CRAWLER MOUNTED

H25 0.10 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS) 1.07 1.03 1.01 1.00 0.94 0.88 0.85 0.82 0.76 0.77 0.77 0.76 0.74 0.72 0.69 0.67 0.67 0.63

H25 0.11 OVER 12,500 LBS THRU 40,000 LBS 1.07 1.03 1.01 1.00 0.94 0.88 0.85 0.82 0.76 0.77 0.77 0.76 0.74 0.72 0.69 0.68 0.67 0.63

3- 32

EP 1110-1-8, Vol. 130 Nov 09

3-38

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

7/31/2009(Vol. 1)



H25 0.14 OVER 160,000 LBS 1.06 1.02 1.01 1.00 0.94 0.89 0.86 0.84 0.78 0.79 0.79 0.78 0.76 0.74 0.72 0.71 0.70 0.67

H25 0.21 ATTACHMENTS, MOBILE SHEARS 1.12 1.06 1.03 1.00 0.95 0.89 0.86 0.84 0.83 0.83 0.82 0.80 0.78 0.77 0.75 0.73 0.72 0.70

H25 0.22 ATTACHMENTS, MATERIAL HANDLING 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.76 0.74 0.72 0.70 0.68

H25 0.23 ATTACHMENTS, CONCRETE PULVERIZERS 1.12 1.06 1.03 1.00 0.95 0.89 0.86 0.84 0.83 0.83 0.82 0.80 0.78 0.77 0.75 0.73 0.72 0.70

H25 0.24 ATTACHMENTS, COMPACTORS 1.12 1.06 1.03 1.00 0.95 0.89 0.86 0.84 0.83 0.83 0.82 0.80 0.78 0.77 0.75 0.73 0.72 0.70

H30 0.00 HYDRAULIC EXCAVATORS, WHEEL MOUNTED

H30 0.01 0 THRU 1.0 CY 1.07 1.03 1.01 1.00 0.94 0.88 0.85 0.82 0.76 0.77 0.77 0.76 0.74 0.72 0.69 0.67 0.67 0.63

H30 0.02 OVER 1.0 CY 1.07 1.03 1.01 1.00 0.94 0.88 0.85 0.83 0.76 0.78 0.77 0.76 0.74 0.72 0.70 0.68 0.67 0.64

H35 0.00 HYDRAULIC SHOVELS, CRAWLER MOUNTED

H35 0.11 DIESEL, 0 CY THRU 5.0 CY 1.06 1.02 1.01 1.00 0.94 0.89 0.86 0.84 0.78 0.79 0.79 0.78 0.76 0.74 0.72 0.70 0.69 0.66

H35 0.12 DIESEL, OVER 5.0 CY 1.06 1.02 1.01 1.00 0.94 0.89 0.86 0.84 0.78 0.79 0.79 0.78 0.76 0.74 0.72 0.71 0.70 0.67

H35 0.21 ELECTRIC, OVER 2.5 CY 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.78 0.80 0.79 0.78 0.76 0.75 0.73 0.71 0.70 0.67

L10 0.00 LAND CLEARING EQUIPMENT 1.12 1.06 1.02 1.00 0.96 0.91 0.88 0.86 0.86 0.85 0.84 0.81 0.80 0.78 0.75 0.73 0.69 0.65

L15 0.00 LANDSCAPING EQUIPMENT 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.83 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

L20 0.00 LIGHTING SETS, TRAILER MOUNTED

L20 0.10 METALLIC VAPOR 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

L25 0.00 LINE STRIPING EQUIPMENT 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

L30 0.00 LOADERS, BELT (Conveyor belts) & ACCESSORIES 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.83 0.82 0.82 0.80 0.78 0.77 0.75 0.73 0.72 0.69

L35 0.00 LOADERS, FRONT END, CRAWLER TYPE 1.12 1.06 1.02 1.00 0.96 0.91 0.88 0.86 0.86 0.85 0.84 0.81 0.80 0.78 0.75 0.73 0.69 0.65

L40 0.00 LOADERS, FRONT END, WHEEL TYPE

3- 33

EP 1110-1-8, Vol. 130 Nov 09

3-39

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

7/31/2009(Vol. 1)

L40 0.11 ARTICULATED, 0 THRU 225 HP 1.13 1.06 1.02 1.00 0.96 0.90 0.87 0.86 0.85 0.85 0.84 0.82 0.80 0.79 0.76 0.74 0.72 0.69

L40 0.12 ARTICULATED, OVER 225 HP 1.12 1.06 1.02 1.00 0.96 0.91 0.88 0.87 0.86 0.86 0.85 0.83 0.81 0.80 0.78 0.76 0.74 0.72

L40 0.20 SKID STEER 1.12 1.06 1.02 1.00 0.96 0.91 0.88 0.86 0.86 0.85 0.84 0.82 0.80 0.79 0.77 0.75 0.73 0.70

L40 0.21 SKID STEER ATTACHMENTS 1.13 1.06 1.02 1.00 0.96 0.90 0.87 0.85 0.85 0.84 0.83 0.81 0.79 0.78 0.76 0.73 0.72 0.69

L40 0.31 TOOL CARRIER & TELESCOPIC HANDLERS, 0 THRU 225 HP 1.13 1.06 1.02 1.00 0.96 0.90 0.87 0.86 0.85 0.85 0.84 0.82 0.80 0.79 0.76 0.74 0.72 0.70

L40 0.32 TOOL CARRIER & TELESCOPIC HANDLERS, OVER 225 HP 1.12 1.06 1.02 1.00 0.96 0.91 0.88 0.87 0.87 0.86 0.85 0.83 0.82 0.81 0.78 0.76 0.75 0.72

L45 0.00 LOADERS / BACKHOE, CRAWLER TYPE 1.12 1.06 1.02 1.00 0.96 0.91 0.88 0.86 0.86 0.85 0.84 0.81 0.79 0.78 0.75 0.72 0.69 0.65

L50 0.00 LOADERS / BACKHOE, WHEEL TYPE 1.13 1.06 1.02 1.00 0.96 0.90 0.87 0.86 0.85 0.85 0.84 0.82 0.80 0.79 0.76 0.74 0.72 0.70

L55 0.00 LOADER / BACKHOE, ATTACHMENTS 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.76 0.74 0.72 0.70 0.68

L60 0.00 LOG SKIDDERS 1.16 1.11 1.05 1.00 0.95 0.91 0.87 0.84 0.83 0.82 0.80 0.78 0.76 0.75 0.74 0.74 0.71 0.70

M10 0.00 MARINE EQUIPMENT (NON DREDGING)

M10 0.11 AQUATIC MAINTENANCE 1.14 1.09 1.05 1.00 0.96 0.92 0.87 0.83 0.82 0.80 0.78 0.78 0.76 0.73 0.70 0.69 0.67 0.64

M10 0.12 AQUATIC MAINTENANCE ATTACHMENTS 1.15 1.10 1.05 1.00 0.96 0.92 0.86 0.82 0.80 0.78 0.77 0.76 0.74 0.71 0.68 0.66 0.65 0.61

M10 0.21 HYDRAULIC CUTTERHEAD DREDGE, 8" OR LESS,TRANSPORTABLE 1.13 1.08 1.05 1.00 0.96 0.93 0.88 0.84 0.83 0.81 0.80 0.79 0.78 0.75 0.72 0.70 0.69 0.66

M10 0.22 HYDRAULIC CUTTERHEAD DREDGE,8" - 12",TRANSPORTABLE 1.13 1.08 1.05 1.00 0.96 0.93 0.88 0.84 0.83 0.81 0.80 0.79 0.78 0.75 0.72 0.70 0.69 0.66

M10 0.23 HYDRAULIC AUGERHEAD DREDGE,12" OR LESS,TRANSPORTABLE 1.13 1.08 1.05 1.00 0.96 0.93 0.88 0.84 0.83 0.81 0.80 0.79 0.78 0.75 0.72 0.70 0.69 0.66

M10 0.24 HYDRAULIC FLOATING PUMPS,12" OR LESS,TRANSPORTABLE 1.13 1.09 1.05 1.00 0.96 0.93 0.87 0.83 0.82 0.80 0.79 0.78 0.77 0.74 0.71 0.69 0.68 0.65

M10 0.25 HYDRUALIC DREDGE PUMPS,12" OR LESS,TRANSPORTABLE 1.14 1.09 1.05 1.00 0.96 0.92 0.87 0.82 0.81 0.79 0.78 0.77 0.76 0.73 0.69 0.68 0.66 0.63

M10 0.26 HYDRAULIC DREDGE / PUMP ATTACHMENTS 1.14 1.09 1.05 1.00 0.96 0.92 0.87 0.82 0.81 0.79 0.78 0.77 0.76 0.73 0.69 0.68 0.66 0.63

M10 0.31 SMALL MECH DREDGES,CLAMSHELL,BARGE-MTD TO 5 CY 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.79 0.80 0.80 0.79 0.77 0.75 0.73 0.72 0.71 0.68

M10 0.32 SMALL MECH DREDGES, AMPHIBIOUS EXCAVATORS 1.06 1.02 1.01 1.00 0.94 0.89 0.86 0.84 0.78 0.79 0.79 0.78 0.76 0.74 0.72 0.70 0.70 0.66

M10 0.33 SMALL MECH DREDGES,HOE-MOUNTED DREDGING ATTACH 1.13 1.08 1.05 1.00 0.96 0.93 0.88 0.84 0.83 0.81 0.79 0.79 0.77 0.75 0.72 0.70 0.69 0.66

3- 34

EP 1110-1-8, Vol. 130 Nov 09

3-40

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

7/31/2009(Vol. 1)

M10 0.41 WORK FLOATS (NON-DREDGING) 1.14 1.09 1.05 1.00 0.96 0.93 0.87 0.83 0.82 0.80 0.79 0.78 0.77 0.74 0.70 0.69 0.68 0.65

M10 0.42 WORK BARGES (SECTIONAL, NON-DREDGING) 1.13 1.08 1.04 1.00 0.96 0.93 0.88 0.84 0.83 0.82 0.80 0.80 0.78 0.76 0.73 0.71 0.70 0.67

M10 0.45 FLAT-DECK OR CARGO BARGE (NON-DREDGING) 1.12 1.08 1.04 1.00 0.97 0.93 0.89 0.85 0.84 0.82 0.81 0.80 0.79 0.77 0.74 0.72 0.71 0.69

M10 0.46 DUMP SCOW (NON-DREDGING) 1.12 1.08 1.04 1.00 0.97 0.93 0.89 0.85 0.84 0.82 0.81 0.80 0.79 0.77 0.74 0.72 0.71 0.69

M10 0.47 DRILL BARGE (NON-DREDGING) 1.12 1.08 1.04 1.00 0.96 0.93 0.88 0.85 0.83 0.82 0.80 0.80 0.79 0.76 0.73 0.72 0.71 0.68

M10 0.48 ALL OTHER BARGES (NON-DREDGING) 1.12 1.08 1.04 1.00 0.96 0.93 0.88 0.85 0.83 0.82 0.80 0.80 0.79 0.76 0.73 0.72 0.71 0.68

M10 0.51 BOATS & LAUNCHES, 0 THRU 250 HP 1.13 1.09 1.05 1.00 0.96 0.93 0.88 0.84 0.82 0.80 0.79 0.78 0.77 0.74 0.71 0.70 0.69 0.65

M10 0.53 BOATS & LAUNCHES, 251 THRU 500 HP 1.13 1.08 1.04 1.00 0.96 0.93 0.88 0.84 0.83 0.81 0.80 0.79 0.78 0.75 0.72 0.71 0.70 0.66

M10 0.54 TUGS, 501 THRU 1,000 HP 1.12 1.08 1.04 1.00 0.96 0.93 0.88 0.85 0.84 0.82 0.81 0.80 0.79 0.76 0.73 0.72 0.71 0.68

M10 0.55 TUGS, 1,000 THRU 2,000 HP 1.12 1.08 1.04 1.00 0.97 0.93 0.89 0.85 0.84 0.82 0.81 0.80 0.79 0.77 0.74 0.72 0.71 0.69

P10 0.00 PILE HAMMER ACCESSORIES - EXTRACTORS & BOX LEADS 1.14 1.08 1.03 1.00 0.94 0.86 0.82 0.81 0.79 0.79 0.77 0.76 0.74 0.72 0.69 0.67 0.65 0.63

P20 0.00 PILE HAMMERS, DOUBLE ACTING

P20 0.10 DIESEL 1.13 1.07 1.03 1.00 0.95 0.88 0.84 0.83 0.81 0.81 0.80 0.78 0.76 0.75 0.72 0.70 0.69 0.67

P20 0.20 PNUEMATIC (STEAM/AIR) 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.76 0.74 0.72 0.70 0.68

P25 0.00 PILE HAMMERS, SINGLE ACTING

P25 0.10 DIESEL 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.76 0.74 0.72 0.70 0.68

P25 0.20 PNUEMATIC (STEAM/AIR) 1.12 1.06 1.03 1.00 0.95 0.89 0.86 0.84 0.83 0.83 0.82 0.80 0.78 0.77 0.75 0.73 0.72 0.70

P30 0.00 PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORY 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.76 0.74 0.72 0.70 0.68

P35 0.00 PIPELAYERS 1.12 1.06 1.02 1.00 0.96 0.91 0.88 0.87 0.86 0.86 0.85 0.82 0.80 0.79 0.76 0.73 0.70 0.66

P40 0.00 PLATFORMS & MAN-LIFTS 1.06 1.02 1.01 1.00 0.94 0.89 0.87 0.84 0.79 0.80 0.79 0.78 0.77 0.75 0.73 0.71 0.70 0.67

P45 0.00 PUMPS, GROUT 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.84 0.83 0.83 0.82 0.81 0.79 0.77 0.75 0.73 0.72 0.70

P50 0.00 PUMPS, WATER, CENTRIFUGAL, TRASH

3- 35

EP 1110-1-8, Vol. 130 Nov 09

3-41

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

7/31/2009(Vol. 1)

P50 0.11 ENGINE DRIVE 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

P50 0.12 ELECTRIC DRIVE 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

P50 0.21 WHEEL MOUNTED, ENGINE DRIVE 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

P50 0.22 WHEEL MOUNTED, ELECTRIC DRIVE 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

P50 0.31 HOSES, PUMP, SUCTION & DISCHARGE 1.11 1.06 1.03 1.00 0.96 0.89 0.86 0.85 0.83 0.83 0.82 0.81 0.79 0.78 0.76 0.74 0.73 0.71

P55 0.00 PUMPS, WATER, SUBMERSIBLE

P55 0.01 ENGINE DRIVE 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

P55 0.02 ELECTRIC DRIVE 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.84 0.83 0.83 0.82 0.81 0.79 0.77 0.75 0.73 0.72 0.70

P60 0.00 PUMPS, WATER, CENTRIFUGAL, DEWATERING

P60 0.11 SKID MOUNTED, ENGINE DRIVE 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

P60 0.12 SKID MOUNTED, ELECTRIC DRIVE 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.84 0.83 0.83 0.82 0.81 0.79 0.77 0.75 0.73 0.72 0.70



P65 0.00 PUMPS, WATER, DIAPHRAGM

P65 0.11 SKID MOUNTED, ENGINE DRIVE 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

P65 0.12 SKID MOUNTED, ELECTRIC DRIVE 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.84 0.83 0.83 0.82 0.81 0.79 0.77 0.75 0.73 0.72 0.70



P70 0.00 PUMPS, WATER (For core drills)

P70 0.01 ENGINE DRIVE 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.81 0.80 0.79 0.77 0.75 0.73 0.71 0.70 0.67

P70 0.02 ELECTRIC DRIVE 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.81 0.80 0.79 0.77 0.75 0.73 0.71 0.70 0.67

R10 0.00 RIPPERS & HYDRAULIC BANK SLOPERS (Add cost for point wear) 1.12 1.06 1.02 1.00 0.96 0.91 0.88 0.86 0.86 0.85 0.84 0.81 0.79 0.78 0.75 0.72 0.69 0.65

3- 36

EP 1110-1-8, Vol. 130 Nov 09

3-42

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

7/31/2009(Vol. 1)

R15 0.00 ROLLERS, STATIC, TOWED, PNEUMATIC 1.17 1.11 1.05 1.00 0.95 0.91 0.86 0.84 0.83 0.81 0.82 0.80 0.78 0.78 0.76 0.73 0.69 0.68

R20 0.00 ROLLERS, STATIC, TOWED, STEEL DRUM 1.17 1.11 1.05 1.00 0.95 0.91 0.86 0.84 0.83 0.81 0.82 0.80 0.78 0.78 0.76 0.73 0.69 0.68

R30 0.00 ROLLERS, STATIC, SELF-PROPELLED

R30 0.01 PNEUMATIC 1.17 1.11 1.05 1.00 0.95 0.91 0.86 0.84 0.83 0.81 0.83 0.81 0.79 0.78 0.76 0.74 0.70 0.69

R30 0.02 SMOOTH DRUM 1.16 1.11 1.05 1.00 0.95 0.91 0.87 0.84 0.83 0.82 0.83 0.81 0.79 0.78 0.77 0.74 0.70 0.70

R30 0.03 TAMPING FOOT, LANDFILL & SOIL COMPACTORS 1.17 1.11 1.05 1.00 0.95 0.91 0.86 0.84 0.83 0.81 0.83 0.81 0.79 0.78 0.76 0.74 0.69 0.69

R40 0.00 ROLLERS, VIBRATORY, TOWED 1.17 1.11 1.05 1.00 0.95 0.90 0.86 0.84 0.82 0.81 0.82 0.80 0.78 0.77 0.75 0.73 0.68 0.68

R45 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM 1.17 1.11 1.05 1.00 0.95 0.90 0.86 0.84 0.82 0.81 0.82 0.80 0.78 0.77 0.75 0.73 0.68 0.68

R50 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE DRUM 1.18 1.12 1.06 1.00 0.95 0.90 0.85 0.83 0.82 0.80 0.81 0.79 0.77 0.76 0.74 0.71 0.67 0.66

R55 0.00 ROOFING EQUIPMENT 1.12 1.06 1.03 1.00 0.95 0.89 0.86 0.84 0.83 0.83 0.82 0.80 0.78 0.77 0.75 0.73 0.72 0.70

S10 0.00 SCRAPERS, ELEVATING

S10 0.01 0 THRU 200 HP 1.11 1.05 1.01 1.00 0.96 0.91 0.88 0.87 0.86 0.85 0.84 0.81 0.78 0.77 0.72 0.71 0.68 0.64

S10 0.02 OVER 200 HP 1.11 1.06 1.01 1.00 0.96 0.91 0.88 0.87 0.86 0.85 0.84 0.81 0.78 0.77 0.72 0.71 0.68 0.63

S15 0.00 SCRAPERS, CONVENTIONAL 1.10 1.05 1.01 1.00 0.96 0.92 0.89 0.87 0.86 0.86 0.84 0.82 0.79 0.78 0.74 0.72 0.70 0.65

S20 0.00 SCRAPERS, TANDEM POWERED 1.10 1.05 1.01 1.00 0.96 0.92 0.89 0.87 0.86 0.86 0.84 0.82 0.79 0.78 0.74 0.72 0.70 0.65

S25 0.00 SCRAPERS, TRACTOR DRAWN 1.10 1.05 1.01 1.00 0.96 0.92 0.88 0.87 0.86 0.86 0.84 0.81 0.79 0.78 0.73 0.71 0.69 0.64

S30 0.00 SCREENING & CRUSHING PLANTS

S30 0.10 CONVEYORS 1.11 1.06 1.03 1.00 0.96 0.90 0.86 0.85 0.84 0.84 0.83 0.82 0.80 0.78 0.76 0.75 0.74 0.72

S30 0.20 CRUSHERS - VERTICAL & HORIZONTAL SHAFT IMPACTOR 1.10 1.06 1.02 1.00 0.96 0.90 0.87 0.86 0.85 0.84 0.84 0.82 0.81 0.79 0.77 0.76 0.75 0.73

S30 0.21 CRUSHERS - CONE 1.10 1.06 1.02 1.00 0.96 0.90 0.87 0.86 0.85 0.84 0.84 0.82 0.81 0.79 0.77 0.76 0.75 0.73

S30 0.22 CRUSHERS - JAW 1.10 1.06 1.02 1.00 0.96 0.90 0.87 0.86 0.85 0.84 0.84 0.82 0.81 0.79 0.77 0.76 0.75 0.73

S30 0.30 SCREENING PLANT 1.11 1.06 1.03 1.00 0.96 0.90 0.86 0.85 0.84 0.84 0.83 0.82 0.80 0.78 0.76 0.75 0.74 0.72

3- 37

EP 1110-1-8, Vol. 130 Nov 09

3-43

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

7/31/2009(Vol. 1)

S35 0.00 SNOW REMOVAL EQUIPMENT 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

S40 0.00 SOIL & ROAD STABILIZERS 1.11 1.05 1.01 1.00 0.96 0.91 0.88 0.87 0.86 0.85 0.84 0.81 0.78 0.77 0.72 0.71 0.68 0.64

S45 0.00 SPLITTERS, ROCK & CONCRETE 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.76 0.74 0.72 0.70 0.68

T10 0.00 TRACTOR BLADES & ATTACHMENTS (including agricultural) 1.12 1.06 1.02 1.00 0.96 0.91 0.88 0.86 0.86 0.85 0.84 0.81 0.80 0.78 0.75 0.73 0.69 0.65

T15 0.00 TRACTORS, CRAWLER (DOZER) (includes blade)

T15 0.01 0 THRU 225 HP 1.13 1.06 1.02 1.00 0.95 0.90 0.87 0.85 0.85 0.84 0.83 0.80 0.78 0.77 0.74 0.70 0.67 0.62

T15 0.02 226 HP THRU 425 HP 1.12 1.06 1.02 1.00 0.96 0.91 0.88 0.86 0.86 0.85 0.84 0.81 0.79 0.78 0.75 0.72 0.69 0.65

T15 0.03 OVER 425 HP 1.12 1.06 1.02 1.00 0.96 0.91 0.88 0.87 0.86 0.86 0.85 0.82 0.80 0.79 0.76 0.74 0.71 0.67

T20 0.00 TRACTORS, WHEEL TYPE (DOZER) 1.16 1.10 1.05 1.00 0.95 0.91 0.87 0.85 0.84 0.82 0.81 0.78 0.77 0.75 0.75 0.74 0.72 0.70

T25 0.00 TRACTORS, AGRICULTURAL

T25 0.10 CRAWLER 1.16 1.11 1.05 1.00 0.95 0.91 0.87 0.84 0.83 0.82 0.80 0.78 0.76 0.75 0.74 0.74 0.71 0.70

T25 0.20 WHEEL 1.17 1.11 1.05 1.00 0.95 0.91 0.86 0.84 0.83 0.81 0.80 0.77 0.76 0.74 0.74 0.73 0.71 0.69

T30 0.00 TRENCHERS, CHAIN TYPE CUTTER 1.17 1.11 1.05 1.00 0.95 0.90 0.83 0.84 0.82 0.81 0.79 0.76 0.73 0.71 0.70 0.68 0.63 0.60

T35 0.00 TRENCHERS, WHEEL TYPE CUTTER 1.17 1.11 1.05 1.00 0.95 0.90 0.83 0.84 0.82 0.81 0.79 0.76 0.73 0.71 0.70 0.68 0.63 0.60

T40 0.00 TRUCK OPTIONS

T40 0.10 CRANES / HOISTS, PERSONNEL & MATERIAL HANDLING 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

T40 0.20 DUMP BODY, REAR 1.11 1.06 1.03 1.00 0.96 0.90 0.86 0.85 0.84 0.84 0.83 0.81 0.80 0.78 0.76 0.74 0.73 0.71

T40 0.30 FLATBEDS, WITH SIDES 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

T40 0.41 HOIST, ELECTRIC DRIVE 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

T40 0.50 TRANSIT MIXERS 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.84 0.83 0.83 0.82 0.81 0.79 0.77 0.75 0.73 0.72 0.70

T40 0.60 WATER TANKS 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.81 0.80 0.79 0.77 0.75 0.73 0.71 0.70 0.67

T40 0.70 ALL OTHER OPTIONS 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.82 0.82 0.81 0.80 0.78 0.76 0.74 0.72 0.71 0.69

3- 38

EP 1110-1-8, Vol. 130 Nov 09

3-44

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

7/31/2009(Vol. 1)

T45 0.00 TRUCK TRAILERS

T45 0.10 BOTTOM DUMP 1.11 1.06 1.03 1.00 0.96 0.90 0.86 0.85 0.84 0.84 0.83 0.82 0.80 0.78 0.76 0.75 0.74 0.72

T45 0.20 END DUMP 1.11 1.06 1.03 1.00 0.96 0.90 0.86 0.85 0.84 0.84 0.83 0.82 0.80 0.78 0.76 0.75 0.74 0.72

T45 0.30 PUP TRAILER 1.11 1.06 1.03 1.00 0.96 0.90 0.86 0.85 0.84 0.84 0.83 0.81 0.80 0.78 0.76 0.74 0.73 0.71

T45 0.41 LOWBOY, RIGID NECK, DROP DECK 1.11 1.06 1.03 1.00 0.96 0.90 0.86 0.85 0.84 0.84 0.83 0.82 0.80 0.78 0.76 0.75 0.74 0.72

T45 0.50 FLATBED TRAILER 1.11 1.06 1.03 1.00 0.96 0.90 0.86 0.85 0.84 0.84 0.83 0.82 0.80 0.78 0.76 0.75 0.74 0.72

T45 0.60 MISCELLANEOUS / UTILITY 1.11 1.06 1.03 1.00 0.96 0.90 0.86 0.85 0.84 0.84 0.83 0.82 0.80 0.78 0.76 0.75 0.74 0.72

T45 0.70 WATER TANKER TRAILER 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.76 0.74 0.72 0.70 0.68

T45 0.80 DECONTAMINATION FACILITY 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.81 0.80 0.79 0.77 0.75 0.73 0.71 0.70 0.67

T45 0.90 TANK TRAILERS 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.76 0.74 0.72 0.70 0.68

T50 0.00 TRUCKS, HIGHWAY (Add attachments as required)

T50 0.01 0 THRU 10,000 GVW 1.12 1.07 1.04 1.00 0.96 0.91 0.89 0.88 0.85 0.85 0.88 0.85 0.86 0.88 0.87 0.85 0.81 0.76

T50 0.02 OVER 10,000 THRU 30,000 GVW (Chassis only - Add options) 1.12 1.07 1.03 1.00 0.96 0.91 0.89 0.88 0.86 0.86 0.88 0.86 0.86 0.88 0.87 0.85 0.81 0.77

T50 0.03 OVER 30,000 GVW (Chassis only - Add options) 1.12 1.07 1.03 1.00 0.96 0.91 0.89 0.88 0.86 0.86 0.88 0.86 0.86 0.88 0.88 0.85 0.81 0.77

T55 0.00 TRUCKS, OFF-HIGHWAY

T55 0.10 RIGID FRAME 1.09 1.06 1.02 1.00 0.95 0.88 0.83 0.82 0.81 0.80 0.78 0.77 0.76 0.74 0.71 0.67 0.65 0.65

T55 0.20 ARTICULATED FRAME 1.09 1.06 1.02 1.00 0.95 0.88 0.83 0.82 0.80 0.79 0.77 0.76 0.75 0.73 0.70 0.66 0.64 0.63

T56 0.00 TRUCKS,OFF-HIGHWAY/PRIME MOVER TRACTORS & WAGONS

T56 0.10 PRIME MOVER TRACTORS 1.09 1.06 1.02 1.00 0.95 0.88 0.83 0.82 0.81 0.80 0.78 0.77 0.76 0.74 0.71 0.67 0.65 0.65

T56 0.20 WAGONS, BOTTOM DUMP 1.09 1.06 1.02 1.00 0.95 0.88 0.83 0.82 0.80 0.79 0.77 0.76 0.75 0.73 0.70 0.66 0.64 0.63

T56 0.30 WAGONS, REAR DUMP 1.10 1.07 1.03 1.00 0.95 0.87 0.82 0.81 0.80 0.78 0.76 0.75 0.74 0.72 0.69 0.65 0.63 0.62

T57 0.00 TRUCKS, VACUUM 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.83 0.82 0.82 0.80 0.78 0.77 0.75 0.73 0.72 0.69

3- 39

EP 1110-1-8, Vol. 130 Nov 09

3-45

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

7/31/2009(Vol. 1)

T60 0.00 TRUCKS, WATER, OFF-HIGHWAY 1.10 1.07 1.03 1.00 0.95 0.87 0.82 0.81 0.80 0.78 0.76 0.75 0.74 0.72 0.69 0.65 0.63 0.62

T65 0.00 TUNNEL/MINING EQUIPMENT

T65 0.10 DRIFTING & TUNNELING DRILLS 1.19 1.14 1.07 1.00 0.93 0.86 0.81 0.79 0.73 0.71 0.70 0.69 0.67 0.66 0.64 0.62 0.61 0.59

T65 0.20 TUNNEL BORING MACHINES 1.11 1.06 1.03 1.00 0.96 0.90 0.87 0.85 0.84 0.84 0.83 0.82 0.80 0.78 0.77 0.75 0.74 0.72

T65 0.30 PRODUCTION DRILLING RIGS 1.20 1.15 1.07 1.00 0.93 0.86 0.80 0.79 0.72 0.70 0.69 0.68 0.67 0.66 0.63 0.62 0.60 0.59

T65 0.40 ROADHEADERS & CONTINUOUS MINERS 1.11 1.06 1.03 1.00 0.96 0.90 0.86 0.85 0.84 0.84 0.83 0.82 0.80 0.78 0.76 0.75 0.73 0.72

T65 0.50 ROCK BOLTING EQUIPMENT 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.83 0.82 0.82 0.80 0.78 0.77 0.75 0.73 0.72 0.69

T65 0.61 LOADING & HAULING EQUIPMENT, DIESEL OR GAS 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.84 0.83 0.83 0.82 0.81 0.79 0.77 0.75 0.73 0.72 0.70

T65 0.62 LOADING & HAULING EQUIPMENT, ELECTRIC 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.85 0.83 0.83 0.82 0.81 0.79 0.77 0.75 0.74 0.72 0.70

T65 0.63 LOADING & HAULING EQUIPMENT, AIR-POWERED 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.76 0.74 0.72 0.70 0.68

T65 0.70 LOCOMOTIVES 1.11 1.06 1.03 1.00 0.95 0.89 0.86 0.84 0.83 0.83 0.82 0.81 0.79 0.77 0.75 0.73 0.72 0.70

T65 0.90 OTHER TUNNELING EQUIPMENT 1.12 1.07 1.03 1.00 0.95 0.89 0.85 0.84 0.83 0.82 0.82 0.80 0.78 0.77 0.75 0.73 0.72 0.69

W10 0.00 WAGONS, BOTTOM DUMP 1.09 1.06 1.02 1.00 0.95 0.88 0.83 0.82 0.80 0.79 0.77 0.76 0.75 0.73 0.70 0.66 0.64 0.63

W15 0.00 WAGONS, REAR DUMP 1.09 1.06 1.02 1.00 0.95 0.88 0.83 0.82 0.80 0.79 0.77 0.76 0.75 0.73 0.70 0.66 0.64 0.63

W25 0.00 WATER & CO2 BLASTERS

W25 0.10 LOW PRESSURE, (< 5,000 PSI) 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.81 0.80 0.79 0.77 0.75 0.73 0.71 0.70 0.67

W25 0.20 HIGH PRESSURE, (>= 5,000 PSI) 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.81 0.80 0.79 0.77 0.75 0.73 0.71 0.70 0.67

W25 0.30 STEAM CLEANERS 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.81 0.80 0.79 0.77 0.75 0.73 0.71 0.70 0.67

W25 0.40 CO2 BLASTERS 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.76 0.74 0.72 0.70 0.68

W25 0.50 WET ABRASIVE BLASTING SYSTEM (TORBO) 1.13 1.07 1.03 1.00 0.95 0.88 0.84 0.82 0.81 0.80 0.79 0.78 0.76 0.74 0.71 0.69 0.68 0.66

W30 0.00 WATER TANKS

W30 0.10 PORTABLE WITH WHEELS 1.10 1.07 1.03 1.00 0.95 0.87 0.82 0.81 0.80 0.78 0.76 0.75 0.74 0.72 0.69 0.65 0.63 0.62

3- 40

EP 1110-1-8, Vol. 130 Nov 09

3-46

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17


CATEGORY



EP 1110-1-8

7/31/2009(Vol. 1)

W30 0.20 SKID MOUNTED 1.10 1.07 1.03 1.00 0.95 0.87 0.82 0.81 0.80 0.78 0.76 0.75 0.74 0.72 0.69 0.65 0.63 0.62

W35 0.00 WELDERS

W35 0.10 ENGINE DRIVEN 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.81 0.80 0.79 0.77 0.75 0.73 0.71 0.70 0.67

W35 0.20 ELECTRIC DRIVEN 1.12 1.07 1.03 1.00 0.95 0.88 0.85 0.83 0.82 0.82 0.81 0.79 0.77 0.76 0.74 0.72 0.70 0.68

3- 41

EP 1110-1-8, Vol. 130 Nov 09

3-47


EP 1110-1-8, Vol. 130 Nov 09

3-48

1. The unit of equipment is not listed in table 2-1.

2. The equipment is contractor owned.

3.

a.b.c. Serial number indicates year of manufacture = 1997d. 1997 = $195,628

e.f.

= x $2,053/tire = $8,212g.

4.

a. =b. = 1997

5.

Horsepower is 170 hp (fuel is Diesel off-road)

Weight = 35,100 lbs

Use the actual cost data as follows:

Data for the unit in question:

Caterpillar front-end wheel loaderModel 950-F11, 4WD, 3.25 CY capacity

Drive tire (DT) size = 23.50 x 25, 16 ply, L-3 (appendix F tire code ANNB5)DT cost (2009)

Hourly rate is computed as follows:

(includes all regional discounts, sales tax and freight)

STANDBY HOURLY RATE CALCULATION FOR OVERAGE EQUIPMENT

EXAMPLE

Actual purchase price in

Assume the following set of given information for the rate calculation example:

Year of manufacture $195,628

4 tires

Purchase price (TEV)

Figure 3-2. Total Hourly Rate Calculation for Overage Equipment

EP 1110-1-8, Vol. 130 Nov 09

3-49

1.

a.(1)(2)(3) 2009(4) 1997(5) 170(6) 0(7)

3D-off

0 None(8) 351 cwt

(9)

Size/Ply App F Code No. Unit Price Cost(a) 0 $0 $0(b) 23.5X25/16Ply ANNB5 4 $2,053 $8,212(c) 0 $0 $0(d) $8,212

(10)$0 $195,628

b. 0.11c.

(1) 45(2) A AVERAGE(3) B 0.075(4) 9,250(5) 0.25(6) 0.031(7) 0.000(8) 0.111(9)

(a) 0.83(b) 0.54(c) 0.92

0.70

Tire Wear Factor:

ID No:

Drive (DT):

Total Tire Cost:

EQUIPMENT INFORMATION AND EXPENSE FACTORS

Equipment Specification Data:Equipment Description: Model and Series:

Loader, Front-end, Wheel, 4WD, 4 CY capacityCaterpillar Model 950-F11

(10)

USE THIS WORKSHEET TO COMPUTE A HOURLY RATE FOR EQUIPMENT THAT IS NOT IN THIS PAMPHLET OR IS IN THE PAMPHLET BUT NOT EQUIVALENT IN SIZE, CAPACITY, HORSEPOWER OR VALUE. (See Appendix A for a blank form)

Region 01



Front (FT):Drive (DT):Trailing (TT):

Filter, Oil, and Grease (FOG) Factor (E G D):

Economic Key (EK):

Trailing (TT):







L40Category and Subcategory Number:USE APPENDIX D TO COMPLETE THE FOLLOWING DATA:

Tire size and number of tires: (Cost of tires based on present year - see 1.a.(3) and Appendix F)







Fuel type:



Front (FT):




EP 1110-1-8, Vol. 130 Nov 09

3-50

2.

a. = $0

(1) Discount: (List Price + Accessories) x Discount Code

{1.a.(10)} {1.c.(3)}($0 + $0.00) x 0.075 = $0

(2) Subtotal {2.a.} - {2.a.(1)} Subtotal = $0

(3) Sales or Import Tax: Subtotal x Tax Rate {2.a.(2)} {Appendix B}

$0 x 6.00% = $0

(4) Subtotal = $0

b. x Freight Rate

per cwt{1.a.(8)} {Appendix B}

0,000 cwt x $0.00 /cwt = $0

c. TOTAL[2.]: = $195,628

3.

a. LIFE / = N {1.c.(4)} {Appendix B}

9,250 hr / = 6.80 yrs

4.

a.(1) Tire Cost Index (TCI):


{1.a.(4)} / = TCI Appendix E, EK=100

2431 / = 0.719


[$195,628 x (1.0-0.25) - (0.719 x $8,212 )] / 9,250 /hr = $15.22 /hr

3382

Region 01

EQUIPMENT VALUE


Total Discounted Price: {Subtotal: 2.a.(2) + 2.a.(3)}

Freight:

(See chapter 3 for used and overage equipment rate adjustments.)


OWNERSHIP COST

Depreciation

Tire Index, Present Year or Year of Use

{1.a.(3)}Appendix E, EK=100

Shipping Weight

1,360 hr/yr


Working Hours Per Year (WHPY)

{2.a.(4)} + {2.b} OR actual purchase price {1a.(10)}


EP 1110-1-8, Vol. 130 Nov 09

3-51

4.

b.

(1) [( N - 1.0) x (1.0 + SLV) + 2.0] / (2.0 x N) =Avg Value

Factor{3.a.} {1.c.5.} {3.a.} (AVF)

[(6.80 yr - 1.0) x (1.0 + 0.25) + 2.0] / (2.0 x 6.80 yr) = 0.680




$195,628 x 0.680 x 3.90% / 1,360 hr/yr = $3.81 /hr

c. TOTAL [4.]: = $19.03 /hr

{4.a.(2)} + {4.b.(2)}

5.

a.

(1)

Fuel Factor x Horsepower (hp) xFuel Cost per Gallon

(gal) {1.c.(6)} {1.a.(5)} {Appendix B}

0.000 x 0 hp x $0.00 /gal = $0.00 /hr

(2)

Fuel Factor x hp x Fuel Cost per gal{1.c.(7)} {1.a.(6)} {Appendix B}

0.000 x 0 hp x $0.00 /gal = $0.00 /hr

(3) Total [5.a.] = $0.00 /hr{5.a (1)} + {5.a (2)}

b.

(1)

FOG Factor xEquipment Hourly Fuel

Cost xLabor Adjustment

Factor (LAF){1.c.(8)} {5.a.(1)} {Appendix B}

0.000 x $0.00 /hr x 0.00 = $0.00 /hr

Equipment:

Equipment:

Carrier:

Total Hourly Fuel Cost:

FOG Cost:

TOTAL HOURLY OWNERSHIP COST:

OPERATING COST

Fuel Costs:

Region 01

OWNERSHIP COST (Continued)

Facilities Capital Cost of Money (FCCM):


EP 1110-1-8, Vol. 130 Nov 09

3-52

5.

(2) Carrier:



0.000 x $0.00 /hr x 0.00 = $0.00 /hr

(3) = $0.00 /hr{5.b.(1)} + {5.b.(2)}

c. = $0.00 hr

d.

(1)

Economic Index, Present Year or

Year of Use,{1.a.(3)}

/ Economic Index, Year of Manufacture,

{1.a.(4)}

Appendix E, EK={1.c.(1)}

Appendix E, EK={1.c.(1)}

0000 / 0000 = 0.000

(2)

RCF x EAF x LAF = RF{1.c.(10)} {5.d.(1)} {Appendix B}

0.00 x 0.000 x 0.00 = 0.000

(3) Repair Cost:


[$0 - (0.000 x $0)] x 0.000 / 0

(4) = $0.00 /hr


Region 01

Total [5.b.]Total Hourly FOG Cost:


Total Hourly Repair Cost: Total [5.d.]

Alternative Fuel/FOG Cost: Total [5.c.]

Economic Adjustment Factor (EAF):EK is from {1.c.(1)}

Repair Factor (RF):

(See chapter 2, paragraph 2.24.d. for guidance on when to use.)

Repair Cost:


EP 1110-1-8, Vol. 130 Nov 09

3-53

5. OPERATING COST (Continued)

e. Tire Wear Cost: (Use current price levels. See Appendix F.)



(1.5 x $0) / (1.8 x 0.00 x 0 hrs) = $0.00/hr

(2)


(1.5 x ($0) / (1.8 x 0.00 x 0 hrs = $0.00/hr

(3)


(1.5 x $0) / (1.8 x 0.00 x 0 hr) = $0.00/hr

(4) Total Tire Wear Cost: Total [5.e.] = $0.00/hrSum {5.e.(1)} through {5.e.(3)}

f.



$0.00/hr x (0.15 x 0.00) Total [5.f.] = $0.00/hr

g. Total [5.] = $0.00/hr

TOTAL HOURLY OPERATING COST:Sum {5.a.} through {5.f.}

Region 01

Drive Tires (DT):

Trailing Tires (TT):

Tire Repair Cost:


EP 1110-1-8, Vol. 130 Nov 09

3-54

6.

a.

Ownership Cost + Operating Cost{4.c.} {5.g.}

$0.00 /hr + $0.00 /hr = $0.00 /hr

See Figure 3-1 for hourly rate calculations for overage equipment

b.


{4.a.(2)} {4.b.(2)} {5.g.}

$0.00 /hr + $0.00 /hr x 40 hr/wk / 60 hr/wk + $0.00 /hr = $0.00 /hr

c.


($15.22 /hr x 0.50) + $3.81 /hr = $11.42 /hr






example:60 hr/wk

example:60 hr/wk

Region 01

HOURLY RATES

Total Hourly Rate: [based on 40 hours per week (wk)]



EP 1110-1-8, Vol. 130 Nov 09

3-55


EP 1110-1-8, Vol. 130 Nov 09

3-56

4-1

CHAPTER 4.0 - METHODOLOGY FOR DREDGING PLANT AND MARINE EQUIPMENT

SECTION I. GENERAL

4.1 Contents

This chapter contains the methodology used to compute ownership and operating rates for dredging plant and permanent floating plant such as floating pile-driving equipment. Dredging plant is marine equipment used for dredging operations for the majority of its life or designed and built for marine/dredging use.

4.2 General

a. The ownership and operating rates provided in table 2-1, category M-10, are based on the methodology in chapter 2 for non-dredging equipment. However, the cost data (Acquisition Cost, Horsepower, and Fuel Type) may be used for calculation of dredging plant and marine equipment rates, provided they are calculated in accordance with the methodology provided in this chapter.

b. Table 4-1 shows ownership and operating cost factors for various types of dredging plant. When a type of plant is not listed, the cost is estimated by using the factors listed in this table for a similar type of plant. c. The methodology for determining operating rates for hopper dredges was omitted from this pamphlet due to the limited number of hopper dredges and the complexity of the methods used to calculate the rates. Further information can be found in Engineer Regulation (ER) 1110-2-1302, Engineering and Design, Civil Works Cost Engineering, on the Internet at http://140.194.76.129/publications/eng-regs/er1110-2-1302/toc.htm, and in Engineer Technical Letter (ETL) 1110-2-573 Engineering and Design: Construction Cost Estimating Guide for Civil Works located at http://140.194.76.129/publications/eng-tech-ltrs/etl1110-2-573/toc.htm. The methodology for calculating ownership cost is in section V of this chapter. d. For mechanical dredges, the cost of the bucket is typically included in the plant value; therefore, no additional allowance should be made for ownership cost. If the bucket cost is not included in the plant value, the bucket may be treated as a separate unit of equipment.

EP 1110-1-8, Vol. 130 Nov 09

http://140.194.76.129/publications/eng-regs/er1110-2-1302/toc.htm

http://140.194.76.129/publications/eng-regs/er1110-2-1302/toc.htm

4-2

SECTION II. ANNUAL USE

4.3 Time Available to Dredge

a. The number of months available per calendar year (yr) for dredging shall be based on the work time available to dredge, excluding downtime for major repairs, work in dry dock, bad weather, and environmental restrictions. Figure 4-1 depicts months available for dredging, including mobilization and demobilization, based on historic data collected by the U.S. Army Corps of Engineers’ regional dredge estimating teams. The data in figure 4-1 shall be used for computing the ownership costs unless specified otherwise in the contract documents.

AVAILABLE TIME TO DREDGE BY REGION (In Months)

Type of Dredging Operation

Region Pipeline Bucket Hopper

Atlantic Coast and tributaries 9 10 10

Gulf Coast, Lower Mississippi, and Tributaries

10 10 11

Great Lakes, Upper Mississippi, and Tributaries

8 8 8

West Coast and Tributaries 9 9 9

Figure 4-1. Months Available by Region

SECTION III. LIFE

4.4 Life

The life for determining ownership and operating costs is defined as follows:

a. The Useful Life is expressed in years in table 4-1. It is the economic life of the equipment and is used to develop ownership rates for various types of dredging plant.

EP 1110-1-8, Vol. 130 Nov 09

4-3

b. The Physical Life is expressed in hours (hrs) in table 4-1. It is the life of the unit based on effective working time and is used to develop operating rates for various types of dredging plant.

4.5 Annual Hours Available

The annual hours available to dredge can be established for each type of plant based on the months available and the estimated effective monthly hours worked. Dredging time is defined as effective plus non-effective working time. “Effective working time" is defined as time during the dredging operation when actual production is taking place. "Non-effective working time" is defined as time during the dredging operation when the dredge is operational but no production is taking place. For complete definition of terms see ER 1110-2-1302, Engineering and Design, Civil Works Cost Engineering. The total annual hours available can be expressed by formula, as follows: Available Hours per yr = Months Available/yr x Effective Hours/Month Where:

• Months Available/yr is found in figure 4-1. • Effective Hours/Month is the effective working time.

SECTION IV. SALVAGE VALUE

4.6 Salvage Value (SLV)

The salvage value, expressed as a decimal, is shown in table 4-1 for different types of plant.

SECTION V. OWNERSHIP COST

4.7 Ownership Cost

Ownership cost is calculated based on a percent of plant value. Plant value is the acquisition cost plus the cost of any initial capital improvements. The value of initial capital improvements is based on those betterments, which were made within 1 year of purchase. Capital improvements do not include any replacement or repair work. Repairs or replacements are an operating cost and are covered in the repair cost allowance. Capital improvements are considered betterments, where the plant has been improved (e.g., adding radar or upgrade of engines). (Note: Only the cost difference between replacement of existing similar engines and actual cost for upgrading engines should be considered as capital improvement). For capital improvements not made within the first year after the initial acquisition, see section VIII.

EP 1110-1-8, Vol. 130 Nov 09

a. The ownership cost is determined from the plant value and is the total expense rate based on depreciation and CMR. When cost or pricing data is available, the actual acquisition price shall be used. Otherwise, the value of a similar piece of plant is used and, if necessary, adjusted so that capacity, size, and horsepower are properly considered.

b. Ownership rate is determined on a yearly basis and distributed over a monthly basis. The monthly rate is calculated based on the available use months by using the following formula:

MonthsUseAvailablePercent) CMR Yearly Percent DEPR(Yearly x ValuePlant CostOwnershipMonthly +

=

Where:

• Plant Value = Acquisition price plus initial capital improvements. • Yearly DEPR Percent = Ownership percent per year for depreciation. • Yearly CMR Percent = Ownership percent per year for cost of money rate. • Available Use Months is from figure 4-1.

4.8 Depreciation Factor

Depreciation is computed using the straight-line method. The depreciable value is the acquisition cost, plus initial capital improvements, less estimated salvage. The basis for determining the yearly percentage factor for depreciation is expressed by the following formula:

/NSLV) - (1 Percent DEPRYearly =

Where:

• N = Useful Life from table 4-1. • SLV = Salvage Value from table 4-1.

4.9 The Cost of Money Rate (CMR) Factor

The CMR factor is calculated on a yearly basis and is expressed here as an annual percentage factor. The CMR used in the calculation is the rate in effect at the time the work was performed. This formula is expressed as follows:

4-4

EP 1110-1-8, Vol. 130 Nov 09

2N2](discounSLV)1)(1-[(NPercentCMRYearly CMR) ted++

=

Where:

• N = Useful Life from table 4-1. • SLV = Salvage Value from table 4-1. • Discounted CMR = Cost of money rate (appendix I) reduced by

25 percent for overhead and profit allowance. 4.10 Other Ownership Elements

Taxes, storage (lay up), and insurance are considered indirect (overhead) costs as defined in ER 1110-2-1302, appendix D. These costs are not included in ownership rates since they vary by geographic area and with individual contractors. These costs are considered as overhead costs and are, therefore, not included here so they will not be duplicated in the overhead in the estimate or submitted proposal.

SECTION VI. OPERATING FACTORS

4.11 Hourly Operating Cost

Operating cost is based on effective working time. Dredging plant operating factors are shown in table 4-1. These factors, which are described in paragraph 4.12, are not intended to replace historical data but shall be used when historical data is limited or nonexistent.

4.12 Prime and Secondary Power

Prime power refers to the primary operating engine for the dredge or other piece of attendant plant. Secondary power refers to all other secondary engines or power plants. If more than one secondary power engine is present, the horsepower is totaled. Fuel consumption factors are prepared on the same basis as in chapter 2. Hourly fuel costs are calculated separately for the primary and secondary engines. The formula used is expressed as follows:

Hourly Fuel Cost = Horsepower x Fuel Cost/Gallon x Engine Fuel Factor Where:

• Horsepower is the engines rated horsepower. • Fuel Cost/Gallon is based on values shown in appendix B. See

chapter 3 for fuel cost adjustments.

4-5

EP 1110-1-8, Vol. 130 Nov 09

• Fuel Factor - Gas or Diesel Fuel. The fuel factor is listed in table 4-1 for the primary and secondary engines.

4.13 Water, Lube, and Supplies (WLS)

This factor is similar to the filters, oil, and grease (FOG) factor described in chapter 2. This item is computed as either a percentage of the hourly fuel costs or, if the type of plant has no engine, a reasonable hourly cost should be included.

This factor does not include an allowance for the oiler normally assigned to the dredge or other piece of dredging plant. The formula is expressed as follows:

Water, Lube, and Supply Cost = WLS factor x Hourly Fuel Cost

Where:

• WLS Factor is obtained from table 4-1. • Hourly Fuel cost is calculated as shown in paragraph 4-12.

4.14 Repairs (RPR)

This factor includes an allowance for all major and minor repairs and is similar to the maintenance and repair cost factor (RCF) described in chapter 2. The economic adjustment factor (EAF) and the labor adjustment factor (LAF) are required to develop this cost. The formula is expressed as follows:

Repair Cost = (Total Plant Value x RPR x EAF x LAF) Life in hr

Where:

• Total Plant Value = Acquisition price plus Initial capital improvements. • RPR = Repair Factor from table 4-1. • EAF = Economic Index (present year)/ Economic Index (acquisition

year). • LAF = Labor Adjustment Factor from appendix B. • Life in hrs = Physical Life from table 4-1.

It should be noted that the repair allowance does not include the following estimated additive items:

a. Excessive dredge wear for parts (e.g., cutter teeth and main suction pumps) is not included due to the wide variety of materials being dredged. The original cost of the bucket and normal wear are typically included in the plant value covered in the plant rate. Excessive bucket wear for mechanical dredges is estimated as an additive item or treated as a separate unit of equipment from table 2-1. Allowances for wear due to 4-6

EP 1110-1-8, Vol. 130 Nov 09

4-7

abrasive material should only be included as an additive item if it is warranted and is not considered elsewhere in the estimate.

b. Dry docking costs, which represent an allowance for rental of the dry dock facility, are not included because they vary greatly depending on the facilities available. Repairs incurred while in dry dock, which occur periodically, are in the repairs. Dry docking costs will be allocated on an average annual basis over the years between such occurrences in accordance with Cost Accounting Standards and Generally Accepted Accounting Practices.

c. There is no predetermined allowance in the dredging plant methodology for jobsite yard costs, mobilization, or demobilization. All of these cost elements must be separately estimated to match each project’s construction conditions.

SECTION VII. STANDBY

4.15 Standby Rate

The standby rate is computed by allowing the full ownership cost. In addition to the standby ownership rate, it may be necessary on dredges to include operating costs. Examples of allowable operating cost are as follows: a generator fuel allowance to account for operation of a diesel engine generator for power to operate pumps; navigation lights; minimum crew; etc.

a. Standby is a directed delay by the Government and will not be allowed during periods when the plant would have otherwise been in idle status, such as non-effective working time. Since ownership is calculated based on life in years computed monthly, standby should be paid only when additional time has been directed by the Government. Standby is to be paid on a 24-hour basis.

b. Standby for pipeline and accessories shall be based on pumping mud in determining values from table 4-1.

SECTION VIII. NEGOTIATED PROCUREMENT

4.16 Rates

The calculated dredging plant rates based on the methodology presented in this chapter should be used for preparing a reasonable contract estimate. When adequate cost or pricing data is available and submitted by the contractor for negotiated procurement, the rates may be adjusted in accordance with the methodology in this chapter. Cost or pricing data is defined in FAR 15.4, Contract Pricing.

EP 1110-1-8, Vol. 130 Nov 09

4-8

4.17 Allowance for Additional Capital Improvements

Allowance for additional capital improvements shall be calculated in accordance with accepted general accounting principles. When adequate cost or pricing data is not available, factors for a similar unit of equipment may be used for determining the ownership rate for overage equipment and plant.

4.18 Overage Plant

When the plant has exceeded the useful life given in table 4-1, it is considered overage. The ownership rate for overage plant should be determined with the same methodology described in section V.

a. When actual cost or pricing data is available to adjust the operating rate, the data must be accurate, complete, and established in accordance with accepted general accounting principles.

b. When actual cost or pricing data is not available, the total hourly operating rate for overage equipment shall be computed on the basis that the equipment is equal to the useful life as shown in table 4-1.

4.19 Dredging Plant Purchased Used

For plant purchased used, the ownership and operating rate must be calculated on an individual case, due to the varying conditions. When actual cost or pricing data is not available, the methodology from this chapter shall be used and values for life and salvage from table 4-1 can be adjusted. Support for adjustments can be obtained by calling the Chief, Cost Engineering Branch, Engineering and Construction Division, Walla Walla District, U.S. Army Corps of Engineers (CENWW-EC-X), telephone 509-527-7511 or 509-527-7510.

SECTION IX. RATE CALCULATION EXAMPLE

4.20 Rate Calculation Example

The example shown in figure 4-2 illustrates the use of figure 4-1, table 4-1, and the regional data from appendix B to generate a rate. For illustration purposes, assume that a 24-inch hydraulic dredge (pipeline) was purchased new in 1991 for $3,700,000, including tax and delivery, and there were no initial capital improvements. This example uses 500 hours per month and a discounted CMR of 4.20 percent.

EP 1110-1-8, Vol. 130 Nov 09

Table 4-1. Dredging Plant Cost Factors

Type of Plant Useful

Life Physical

Life Salvage Value

Prime Engine Fuel Factor

Secondary Engine Fuel Factor

WLS %

RPR %

YRS HR SLV HPF G D HPF G D G D Hydraulic Dredges - Pipeline (Cutterhead or Dustpan) (Based on Discharge Diameter) (Non-Truckable)

8 inch and under 5 10,000 0.05 80 0.083 0.045 70 0.072 0.039 20 22 70 9 inch through 10 inch 6 12,000 0.05 80 0.083 0.045 70 0.072 0.039 20 22 80 11 inch through 12 inch 8 16,000 0.05 80 0.083 0.045 70 0.072 0.039 20 22 90 13 inch through 15 inch 15 40,000 0.05 80 0.083 0.045 70 0.072 0.039 20 22 100 16 inch through 17 inch 20 80,000 0.05 80 0.083 0.045 70 0.072 0.039 20 22 110 18 inch through 20 inch 20 100,000 0.05 80 0.083 0.045 70 0.072 0.039 20 22 120 21 inch through 22 inch 25 120,000 0.10 80 0.083 0.045 70 0.072 0.039 20 22 130 23 inch through 24 inch 25 130,000 0.10 80 0.083 0.045 70 0.072 0.039 20 22 130 25 inch through 29 inch 30 135,000 0.10 80 0.083 0.045 70 0.072 0.039 20 22 130 30 inch or larger 30 135,000 0.10 80 0.083 0.045 70 0.072 0.039 20 22 130 Barge Mounted Booster Pump (For Pipeline Dredges) 16 inch through 17 inch 20 80,000 0.05 80 0.083 0.045 70 0.072 0.039 22 24 80 18 inch through 20 inch 20 100,000 0.10 80 0.083 0.045 70 0.072 0.039 22 24 90 21 inch through 22 inch 25 120,000 0.10 80 0.083 0.045 70 0.072 0.039 22 24 100 23 inch through 24 inch 25 130,000 0.10 80 0.083 0.045 70 0.072 0.039 22 24 110 25 inch through 29 inch 30 135,000 0.10 80 0.083 0.045 70 0.072 0.039 22 24 120 30 inch or larger 30 135,000 0.10 80 0.083 0.045 70 0.072 0.039 22 24 120

SLV = Salvage Value HPF = Horsepower Factor G = Gas D = Diesel WLS = Water, Lube and Supplies RPR = Repairs

4-9

EP 1110-1-8, Vol. 130 Nov 09

4-10

Table 4-1. Dredging Plant Cost Factors (Continued)


Life Physical

Life Salvage Value



WLS %

RPR %

YRS HR SLV HPF G D HPF G D G D Mechanical Dredges (Large)1

Clamshell - under 5 cy 8 18,000 0.05 70 0.072 0.039 60 0.062 0.033 22 24 90 Clamshell - 6 cy to 10 cy 13 26,000 0.05 70 0.072 0.039 60 0.062 0.033 22 24 100 Clamshell - 11 cy to 15 cy 20 40,000 0.05 70 0.072 0.039 60 0.062 0.033 22 24 110 Clamshell - 16 cy to 20 cy 25 75,000 0.05 70 0.072 0.039 60 0.062 0.033 22 24 120 Clamshell - 20 cy and over 30 90,000 0.05 70 0.072 0.039 60 0.062 0.033 22 24 130 All Other Types

(Bucket or Dipper) 25 90,000 0.10 70 0.072 0.039 60 0.062 0.033 22 24 120

Barge Mounted Crane with Clamshell Bucket Non - Dredging

Clamshell - under 6 cy 9 18,000 0.05 55 0.055 0.031 45 0.045 0.025 22 24 85 Clamshell - 6 cy to 10 cy 14 28,000 0.05 55 0.055 0.031 45 0.045 0.025 22 24 95 Clamshell - 11 cy to 15 cy 21 42,000 0.05 55 0.055 0.031 45 0.045 0.025 22 24 105

Barge Mounted Lifting Crane 25 Ton to 75 Ton, 45’ Boom 9 18,000 0.05 40 0.040 0.022 30 0.030 0.017 22 24 80 75 Ton to 125 Ton, 60’ Boom 14 28,000 0.05 40 0.040 0.022 30 0.030 0.017 22 24 90 Over 125 Ton, over 60’ Boom 21 42,000 0.05 40 0.040 0.022 30 0.030 0.017 22 24 100

Barges (Used with Dredging) Fuel or Water 20 90,000 0.05 20 0.021 0.011 20 0.021 0.011 18 20 60 Equipment or Work 20 90,000 0.05 20 0.021 0.011 20 0.021 0.011 18 20 60 Derrick 20 90,000 0.10 20 0.021 0.011 20 0.021 0.011 18 20 70 Anchor 20 90,000 0.05 20 0.021 0.011 20 0.021 0.011 18 20 60 Mooring Barge 20 90,000 0.05 20 0.021 0.011 20 0.021 0.011 18 20 60 Dump Scow 20 90,000 0.05 20 0.021 0.011 20 0.021 0.011 18 20 70

SLV = Salvage Value HPF = Horsepower Factor G = Gas D = Diesel WLS = Water, Lube and Supplies RPR = Repairs 1 Sized by the largest bucket used (normally a mud bucket)

EP 1110-1-8, Vol. 130 Nov 09



Life Physical

Life Salvage Value



WLS %

RPR %

YRS HR SLV HPF G D HPF G D G D Boats – See Category M10 Tugs and Tenders (Used with Dredging) Under 500 hp 8 18,000 0.10 80 0.083 0.045 70 0.072 0.039 32 38 80 501 through 1,000 hp 10 40,000 0.10 80 0.083 0.045 70 0.072 0.039 32 38 90 1,001 through 2,000 hp 15 55,000 0.10 80 0.083 0.045 70 0.072 0.039 32 38 100 2,001 through 3,000 hp 20 100,000 0.10 80 0.083 0.045 70 0.072 0.039 32 38 110 Over 3,000 hp 25 120,000 0.10 80 0.083 0.045 70 0.072 0.039 32 38 120 Pipeline and Accessories (Inland Environment) Metal Pipeline (under 20 inch)

Pumping Mud 2 9,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Sand 1 4,500 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Rock (Gravel) 0.3 1,500 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Joints 3 12,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 30 Pontoons/Floats 12 60,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5

Metal Pipeline (20 inch and

Larger)

Pumping Mud 3 12,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Sand 1.5 6,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Rock (Gravel) 0.5 2,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Joints 3 12,00 0.10 0 0.000 0.000 0 0.000 0.000 0 0 30 Pontoons/Floats 12 60,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 SLV = Salvage Value HPF = Horsepower Factor G = Gas D = Diesel WLS = Water, Lube and Supplies RPR = Repairs

4-11

EP 1110-1-8, Vol. 130 Nov 09

4-12



Life Physical

Life Salvage Value



WLS %

RPR %

YRS HR SLV HPF G D HPF G D G D Pipeline and Accessories (Ocean Environment) Metal Pipeline (All sizes)

Pumping Mud 2 9,000 0.40 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Sand 1 4,500 0.40 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Rock (Gravel) 0.3 1,500 0.40 0 0.000 0.000 0 0.000 0.000 0 0 5 Joints 1 4,500 0.40 0 0.000 0.000 0 0.000 0.000 0 0 5 Pontoons/Floats 2 9,000 0.40 0 0.000 0.000 0 0.000 0.000 0 0 5

Metal Pipeline On-Shore

Pumping Mud 3 12,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Sand 1.5 6,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5 Pumping Rock (Gravel) 0.5 2,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5

Standby Calculation: Standby for pipeline and accessories shall be based on pumping mud.

SLV = Salvage Value HPF = Horsepower Factor G = Gas D = Diesel WLS = Water, Lube and Supplies RPR = Repairs

EP 1110-1-8, Vol. 130 Nov 09

ID No:

1.

a.(1)(2)(3) 2009(4) 1991(5) 3,730 hp(6)

(a) 200 hp(b) 1,325 hp(c) 750 hp(d) 200 hp

2,475 hp(7)

(a) $3,700,000(b) $0

$3,700,000

(8) 500 hrs/mo

(9)(a) Excessive Dredge Wear (Gravel) $8,000 /mo(b) $0 /mo(c) $0 /mo(d) $0 /mo(e) $0 /mo

$8,000 /mob.

(1) Labor Adjustment Factor (LAF) 1.12(2) Marine Diesel

$2.41(3) 4.875%(4) 3.900%

c.(1) Economic Index, Acquisition Year 4438(2) 7762

Input data, methodology and notes used in the following sections of this form are or have reference to EP 1110-1-8, CONSTRUCTION EQUIPMENT OWNERSHIP AND EXPENSE SCHEDULE (see chapter 4).

Hydraulic Water Jet

Plant Value:Acquisition Costs

Total Secondary hp

Appendix B, Area Factors Data

Fuel Cost Per GallonFuel type

Appendix E, Economic Index Data (EK 105)

Cost of Money Rate (undiscounted)

Horsepower (hp) - Secondary Engine (s):Electrical GeneratorsHydraulic SystemCutter Head Drive

Horsepower (hp) - Prime

24" Hydraulic Cutter Suction DredgeEllicott Series 4900 Super Dragon

Present Year or Year of Use:Acquisition Year:

Capital ImprovementsTotal Plant Value

MARINE AND DREDGING PLANT INFORMATION AND EXPENSE FACTORS

Region 01

Cost of Money Rate (discounted)

Economic Index, Present Year or Year of Use

Example: The piece of equipment shown is based on a known piece of equipment for illustration purposes only.

USE THIS WORKSHEET TO COMPUTE A MONTHLY AND HOURLY RATE FOR MARINE AND DREDGING PLANT

Hours Worked per Month (Effective Time)

Total Additive Items

Additive Item(s) (Monthly Costs To be Estimated)

Plant Pertinent Data:Equipment Description: Model and Series:

Figure 4-2. Dredging Plant Ownership and Operating Rate Worksheet Page 1 of 4

EP 1110-1-8, Vol. 130 Nov 09

4-13

1.

d.(1) 9 months/yr

e.(1) 25 yrs(2) 130,000 hrs(3) 0.10(4) 0.045(5) 0.039(6) 22%(7) 1.30

2. ANNUAL OWNERSHIP PERCENTAGE FACTORS

a.

1.0 - SLV / N {1.e.(3)} {1.e.(1)}

1.0 - 0.10 / 25 yrs = 3.60% /yr

b.

(N-1) x (1+SLV)+2 x / 2N{1.e.(1)} {1.e.(3)} {Appendix B} {1.e.(1)}(25-1) x (1+ 0.10) + 2 x 3.900% / 50.00 = 2.22% /yr

c. = 5.82% /yr

3. OWNERSHIP COSTSa. Ownership per Year

Plant Value x {1.a.(7)(a)}

$3,700,000 x = $215,340.00 /yr

b. Monthly Ownership Expense

/ Months Available per Year{3.a.} {1.d.(1)}

$215,340.00 /yr / 9 months/yr rounded = $23,927.00 /mo

Prime Engine Fuel Factor (gal/bhp-hr)

Ownership per Year

Depreciation Percent Per Year (DEPR)

Facilities Capital Cost of Money Percent Per Year (FCCM)

Total Ownership Percent Per Year (DEPR + FCCM)

Discounted Money Rate

Secondary Engine Fuel Factor (gal/bhp-hr)WLS (Water, Lube & Supplies Factor) percentRPR (Repair Cost Factor)

MARINE AND DREDGING PLANT INFORMATION AND EXPENSE FACTORS (Continued)

Region 01

SLV (Salvage Value Factor)

Figure 4-1, Available Time to Dredge By Region Data (See Chapter 4, paragraph 4.3 for guidance)

Table 4-1, Dredging Plant Cost Factors DataUseful Life (in Years) for Ownership (N)Physical Life (in Hours) for Repairs

Months Available Per Year (9 months is used for this example)

(DEPR + FCCM)Total Ownership Percent Per Year

{2.c.}5.82%


EP 1110-1-8, Vol. 130 Nov 09

4-14

4. OPERATING COSTS

a. Fuel Cost(1) Prime Engine Fuel

Fuel Factor x HP xFuel Cost per Gallon

{1.e.(4)} {1.a.(5)} {1.b.(2)}0.045 gal/bhp-hr x 3,730 x $2.41 = $404.52 /hr

(2) Secondary Engine Fuel

Fuel Factor x HP x{1.e.(5)} {1.a.(6)} {1.b.(2)}

0.039 gal/bhp-hr x 2,475 x $2.41 = $232.63 /hr

(3) Total Fuel (Prime Engine Fuel + Secondary Engine Fuel) = $637.15 /hr

b. Water, Lube, and Supply (WLS) Cost(1) Prime Engine WLS

WLS Factor x Hourly Fuel Cost{1.e.(6)} {4.a.(1)}0.22 x $404.52 /hr = $88.99 /hr

(2) Secondary Engine WLS WLS Factor x Hourly Fuel Cost

{1.e.(6)} {4.a.(2)}0.22 x $232.63 /hr = $51.18 /hr

(3) Total Fuel (Prime Engine WLS + Secondary Engine WLS) = $140.17 /hr

c. Repair Cost

(1) Economic Adjustment Factor (EAF)Economic Index for

Present Year or Year of Use /

Economic Index for Acquisition

Year{1.c.(2)} {1.c.(1)}7762 / 4438 = 1.749

(2) Repair Cost

Total Plant Value x RPR x EAF x LAF / Life in Hrs {1.a.(7)} {1.e.(7)} {4.c.(1)} {1.b.(1)} {1.e.(2)}

$3,700,000 x 1.30 x 1.749 x 1.12 / 130,000 = $72.48 /hr

Fuel Cost per Gallon

Region 01


EP 1110-1-8, Vol. 130 Nov 09

4-15

4. OPERATING COSTS (Continued)

d. Total Hourly Operating Cost (Fuel + WLS + Repairs) Fuel + WLS + Repairs

{4.a.(3)} {4.b.(3)} {4.c.(2)}$637.15 /hr + $140.17 /hr + $72.48 /hr = $849.80 /hr

e.

Total Hourly

Operating Cost xHrs Worked per

Mo{4.d.} {1.a.(8)}

$849.80 /hr x 500 hrs/mo rounded = $424,900.00 /mo

5. TOTAL MONTHLY RATE

a. Ownership {3.b.} = $23,927.00 /mo

b. Operating {4.e.} = $424,900.00 /mo

c. Total Estimated Additive Items {1.a.(9))} = $8,000.00 /mo

d. = $456,827.00 /mo{5.a.} + {5.b.} + {5.c.}

6. STANDYBY ALLOWANCE

a. Standard Hourly Standby Expense

Monthly Ownership Expense /

Maximum hrs/mo = 30.4 days/mo x 24

hrs/day{3.b.}

$23,927.00 /mo / 730 hrs/mo = $32.78 /hr

b. Generator Fuel Allowance for Dredge (An additional generator fuel allowance may be allowed under certain circumstances. This allowance is applicable to dredges only.)

Generator HP /Total Secondary

HP xSecondary Fuel

Cost{1.a.(6)} {1.a.} {4.a.(2)}200 hp / 2,475 hp x $232.63 = $18.80 /hr

c. TOTAL HOURLY STANDBY ALLOWANCE FOR DREDGE

Standby Expense +Generator Fuel

Allowance{6.a.} {6.b.}

$32.78 /hr + $18.80 /hr = $51.58 /hr

Region 01

Monthly Operating Cost

TOTAL MONTHLY RATE


EP 1110-1-8, Vol. 130 Nov 09

4-16

APPENDIX A REFERENCES

Section I: Required Publications Section II: Related Publications Section III. EFAR Reference Section IV: Government Bookstores Sample Equipment Rate Computation Worksheet

EP 1110-1-8, Vol. 130 Nov 09

A-1

APPENDIX A

REFERENCES SECTION I: REQUIRED PUBLICATIONS

Public Law 92-41. The Renegotiation Act of 1971 [PL 92-41 (85 Stat. 97)].

Federal Acquisition Regulation 15.400. Contract Pricing, Government Printing Office, Washington, DC.

. 30.101. Cost Accounting Standards, Part 30, Government Printing Office, Washington, DC.

. 31.105. Construction and Architect-Engineer Contracts, Government Printing Office, Washington, DC.

. 31.205-10. Cost of Money, Government Printing Office, Washington, DC.

. 31.205-36. Rental Costs, Government Printing Office, Washington, DC.

. 49.000. Termination of Contracts, Government Printing Office, Washington, DC.

. 52.230-2. Cost Accounting Standards, Government Printing Office, Washington, DC.

Engineer Federal Acquisition Regulation Supplement (EFARS). 31.105 Construction and Architect-Engineer Contracts, Regulation Supplement, Government Printing Office, Washington, DC.

. 31.105-100. Contract Clause, Government Printing Office, Washington, DC.

Engineer Regulation 1110-2-1302. Engineering and Design - Civil Works Cost Engineering, U.S. Army Corps of Engineers.

U.S. Department of Labor, Bureau of Labor Statistics. Producer Price Indexes, Government Printing Office, Washington, DC. http://www.bls.gov/ppi/

EP 1110-1-8, Vol. 130 Nov 09

A-2

SECTION II: RELATED PUBLICATIONS

. 2000. Caterpillar Performance Handbook, 31st ed, Peoria, Illinois.

. 2001. Caterpillar Performance Handbook, 32nd ed, Peoria, Illinois.

. 2004. Caterpillar Performance Handbook, 34th ed, Peoria, Illinois.





Caterpillar Tractor Company, Fundamentals of Earthmoving, Peoria, Illinois, 1975.

Energy Information Administration, Official Energy Statistics from the U.S. Government. Electric Power Monthly, Washington, DC.

. Petroleum Marketing Monthly, Washington, DC.

Equipment Watch. 2006. Green Guide for Off-Highway Trucks and Trailers, San Jose, California.

. 2006. Green Guide Volume I, San Jose, California.

. 2006. Green Guide Volume II, San Jose, California.

. 2006. Contractor’s Equipment Cost Guide.

. 2006. Cost Reference Guide.

Euclid, Inc. 1982. Euclid Hauler Handbook, 15th ed, Cleveland, Ohio.

Fiat-Allis Construction Machinery, Inc. 1983. Owning and Operating Costs, Springfield, Illinois.

International Harvester, Pay Line Division. 1975. Earthmoving Principles, Schaumburg, Illinois.

Koehring Company. 1981. Application Manual for Hydraulic Excavators and Shovels, 1st ed, Milwaukee, Wisconsin.

EP 1110-1-8, Vol. 130 Nov 09

A-3

http://www.mitco.com/�

Goodyear Government Sales Department, Federal Open Market & Net State Price List, G302. March 1, 2009. Akron, Ohio.

Mitchell Industrial Tire Company (MITCO), www.mitco.com.

Goodyear Engineered Products, Veyance Technologies, http://www.goodyearep.com/productsDetail.aspx?id=4156.

Goodyear Tire and Rubber Company, U.S. Bulletin 300C, Base Price List. Setpember 1, 2008.

TITAN Tire Corporation, Tire Catalog, Volume 13 2009.

TITAN Tire Corporaiton, OTR Tires, Off-the-Road Tires made by Titan, General Tire, Volume 2. 2009.

Nichols, H L Jr. 2005. Moving the Earth, 5th ed, McGraw-Hill Professional; 5 edition (March 28, 2005).

R S Means Company, Inc. 2009. Labor Rates for the Construction Industry, 36th ed., Kingston, Massachusetts.

Terex Corporation. 1981. Production and Cost Estimating of Material Movement with Earthmoving Equipment, Hudson, Ohio.

EP 1110-1-8, Vol. 130 Nov 09

A-4

http://www.goodyearep.com/productsDetail.aspx?id=4156�

SECTION III: EFAR REFERENCE

EFARS PART 31 CONTRACT COST PRINCIPLE AND PROCEDURES

EAC 95-6

SUBPART 31.1 -- APPLICABILITY 31.105 Construction and Architect-Engineer Contracts. (d)(2)(i)(b) In this case, equipment ownership and operating costs shall be determined using the Construction Equipment Ownership and Operating Expense Schedule published by the U.S. Army Corps of Engineers. 31.105-100 Contract Clause. The contracting officer shall insert the statement at 52.231-5000 in all solicitations and contracts for construction within the United States that are expected to exceed the small purchase threshold. EFARS Clause - 52.231-5000 Equipment Ownership and Operating Expense Schedule. As prescribed in 31.105-100, insert the following clause in all solicitations and contracts for construction that are expected to exceed the small purchase threshold. EQUIPMENT OWNERSHIP AND OPERATING EXPENSE SCHEDULE (MAR 1995) – EFARS. (a) This clause does not apply to terminations. See 52.249-5000, Basis for Settlement of Proposals, and FAR Part 49, Termination of Contracts. (b) Allowable cost for construction and marine plant and equipment in sound workable condition owned or controlled and furnished by a contractor or subcontractor at any tier shall be based on actual cost data for each piece of equipment or groups of similar serial and series for which the Government can determine both ownership and operating costs from the contractor’s accounting records. When both ownership and operating costs cannot be determined for any piece of equipment or groups of similar serial or series equipment from the contractor’s accounting records, costs for that equipment shall be based upon the applicable provisions of EP 1110-1-8, Construction Equipment Ownership and Operating Expense Schedule, Region [Insert roman numeral for the appropriate region of the schedule]. Working conditions shall be considered to

EP 1110-1-8, Vol. 130 Nov 09

A-5

SECTION III: EFAR REFERENCE (Continued) be average for determining equipment rates using the schedule unless specified otherwise by the contracting officer. For equipment not included in the schedule, rates for comparable pieces of equipment may be used or a rate may be developed using the formula provided in the schedule. For forward pricing, the schedule in effect at the time of negotiations shall apply. For retroactive pricing, the schedule in effect at the time the work was performed shall apply. (c) Equipment rental costs are allowable, subject to the provisions of FAR 31.105, Construction and Architect-Engineer Contract, and FAR 31.205-36, Rental Costs. Rates for equipment rented from an organization under common control, lease-purchase arrangements, and sale-leaseback arrangements, will be determined using the schedule, except that actual rates will be used for equipment leased from an organization under common control that has an established practice of leasing the same or similar equipment or unaffiliated lessees. (d) When actual equipment costs are proposed and the total amount of the pricing action exceeds the small purchase threshold, the contracting officer shall request the contractor to submit either certified cost or pricing data, or partial/limited data, as appropriate. The data shall be submitted on Standard Form 1411, Contract Pricing Proposal Cover Sheet.

EP 1110-1-8, Vol. 130 Nov 09

A-6

SECTION IV. GOVERNMENT BOOKSTORES U.S. Government periodicals are sold by the Office of the Superintendent of Documents. Orders may be placed by telephone or fax (Visa/Mastercard is accepted). Telephone: toll free 866-512-1800 (D.C. area: 202-512-1800). Fax: 202-512-2104. Orders may also be placed electronically at Internet address http://bookstore.gpo.gov/. RETURN POLICY: Publications are not accepted for exchange or credit unless an error was made in filling your order. When ordering, please give the following information:

Title of Publication: EP 1110-1-8, Construction Equipment Ownership and Operating Expense Schedule

Region: Region I through XII Volume No. Volume No. 1 through No. 12 Media: CD-ROM

EP 1110-1-8, Vol. 130 Nov 09

A-7

http://bookstore.gpo.gov/�

Use this worksheet to compute rates for equipment that is not in this pamphlet.

1. EQUIPMENT INFORMATION AND EXPENSE FACTORS

ID No.: a. Equipment Specification Data:

(1) Equipment Description: (2) Model and Series: (3) Year of Use: (4) Year Manufactured: (5) Horsepower - Equipment: (6) Horsepower - Carrier: (7) Fuel type: - Equipment: gas/diesel off-road/diesel on-road/electric/air

- Carrier: gas/diesel off-road/diesel on-road/electric/air (8) Shipping Weight (cwt): (9) Tire size and number of tires: (Cost of tires based on year of use – see 1.a.(3) and

appendix F)

No. Size/Ply Unit Price Cost (a) Front (FT): $ $ (b) Drive (DT): $ $ (c) Trailing (TT): $ $ (d) Total Tire Cost: $

USE APPENDIX D TO COMPLETE THE FOLLOWING DATA:

b. Category and Subcategory Number: c. Hourly Expense Calculation Factors:

(1) Economic Key (EK): (2) Condition (C): Average or Severe or Difficult (3) Discount Code (DC): B = 7.5% (0.075) – or – S = 15.0% (0.15) (4) Life in Hours (LIFE): (5) Salvage Value Percentage (SLV): (6) Fuel Factor – Equipment [Electric (E) Gas (G) Diesel (D)]: (7) Fuel Factor – Carrier (E G D): (8) Filters, Oil, and Grease (FOG) Factor (E G D): (9) Tire Wear Factor:

(a) Front (FT): (b) Drive (DT): (c) Trailing (TT):

(10) Repair Cost Factor (RCF):

Equipment Rate Computation Worksheet (copy as needed).

Page 1 of 6

EP 1110-1-8, Vol. 130 Nov 09

A-8

2. EQUIPMENT VALUE a. List Price + Accessories: [at Year of Manufacture] =$

(1) Discount: (List Code) (Discount x es) Accessori Price +

[1.c.(3)] ($ + $ ) x ( ) =-($

(2) Subtotal [2.a.] – [2.a.(1)] Subtotal=$ (3) Sales or Import Tax: Rate)(Tax x (Subtotal)

[2.a.(2)] [Appendix B]

($ ) x ( ) =+$

(4) Total Discounted Price: Subtotal: [2.a.(2)] + [2.a.(3)] Subtotal=$

b. Freight: cwt) per Rate (Freight x Weight)(Shipping[1.a.(8)] [Appendix B]

( cwt) x ($ /cwt) =+$

c. TOTAL EQUIPOMENT VALUE (TEV): TOTAL[2.]:=$ [(2.a.(4)] + [(2.b)]

(See chapter 3 for used and overage equipment rate adjustments.) 3. DEPRECIATION PERIOD (N)

a. N (WHPY)) YearPer Hours (Working / (hr)) hours (LIFE = [1.c.(4)] [Appendix B] ( hr) / ( hr/yr) =

4. OWNERSHIP COST a. Depreciation

(1) Tire Cost Index (TCI):

= 1.a.(3)) on Based Index, (Tire / Mfg) of YrIndex, Tire( Tire Cost Index (TCI) [Appendix E, EK=100] [Appendix E, EK=100]

( ) / ( ) = (TCI)

(2) ) LIFE ( / Cost)]] (Tire x ) TCI ( [ - )]SLV ( - [1.0 x [(TEV)

[2.c.] [1.c.(5)] [4.a.(1)] [1.a.(9)(d)] [1.c.(4)]

[($ ) x [1.0 – ( )] – [( ) x ($ )]] / ( hr)

=$ /hr


Page 2 of 6

EP 1110-1-8, Vol. 130 Nov 09

A-9

4. OWNERSHIP COST (Continued) b. Facilities Capital Cost of Money (FCCM):

(1) Factor Value Avg )] N ([2.0x / 2.0] (SLV)] [1.0 x 1.0] - ) N [[( =++ [3.a.] [1.c.5.] [3.a.] (AVF)

[[( yr) – 1.0] x [1.0 + ( )] + 2.0] / [2.0 x ( yr)]

= (AVF)

(2) ) WHPY ( / Money)-of-Cost (Adjusted x ) AVF( x )TEV (

[2.c] [4.b.(1)] [Appendix B] [Appendix B]

($ ) x ( ) x ( ) / ( hr/yr) =$ /hr

c. TOTAL HOURLY OWNERSHIP COST: TOTAL [4.]: =$ /hr

[4.a.(2)] + [4.b.(2)]

5. OPERATING COST

a. Fuel Costs: (1) Equipment:

(Fuel Factor x (Horsepower (hp)) x (Fuel Cost Per Gallon (gal)) [1.c.(6)] [1.a.(5)] [Appendix B] ( ) x ( hp) x ($ / gal) =$ /hr

(2) Carrier:

(Fuel Factor) x (Horsepower) x (Fuel Cost Per Gallon) [1.c.(7)] [1.a.(6)] [Appendix B]

( ) x ( hp) x ($ /gal) =$ /hr

(3) Total Hourly Fuel Cost: Total [5.a.] =$ /hr [(5.a.(1)] + [5.a.(2)]

b. FOG Cost:

(1) Equipment:

(FOG Factor) x (Equipment Fuel Cost) x (Labor Adjustment Factor (LAF)) [1.c.(8)] [5.a.(1)] [Appendix B]

( ) x ($ /hr) x ( ) =$ /hr


Page 3 of 6

EP 1110-1-8, Vol. 130 Nov 09

A-10


(2) Carrier:

(FOG Factor) x (Carrier Fuel Cost) x (LAF) [1.c.(8)] [5.a.(2) [Appendix B]

( ) x ($ /hr) x ( ) =$ /hr

(3) Total Hourly FOG Cost: Total [5.b.] =$ /hr

[(5.b.(1)] + [5.b.(2)]

c. Alternative Fuel/FOG Cost: Total [5.c.] =$ /hr (See chapter 2, paragraph 24.d. for guidance on when to use.)

d. Repair Cost:

(1) Economic Adjustment Factor (EAF):

(EK is from [1.c.(1)])

(Economic Index for Year 1.a.(3)) / (Economic Index for Year 1.a.(4)) [Appendix E] [Appendix E]

( ) / ( ) = (EAF)



(RCF) x (EAF) x (LAF) = Repair Factor (RF) [1.c.(10)] [5.d.(1)] [Appendix B]

( ) x ( ) x ( ) = (RF)

(3) Repair Cost:

[(TEV) - [(TCI) x (Tire Cost )]] x (RF) / (LIFE) [2.c.] [4.a.(1)] [1.a.(9)(d)] [5.d.(2)] [1.c.(4)] [($ ) – [( ) x ($ )]] x ( ) / ( )

(4) Total Hourly Repair Cost: Total [5.d.] =$ /hr


Page 4 of 6

EP 1110-1-8, Vol. 130 Nov 09

A-11


e. Tire Wear Cost: (Use current price levels. See Appendix F)


[1.5 x (FT Cost)] / [1.8 x (FT Wear Factor) x (Maximum Tire Life Hours)] [1.a.(9)(a)] [1.c.(9)(a)] [Appendix G]

[1.5 x ($ )] / [1.8 x ( ) x ( /hr)]

=$ /hr


[1.5 x (DT Cost)] / [1.8 x (DT Wear Factor) x (Maximum Tire Life Hours)] [1.a.(9)(b)] [1.c.(9)(b)] [Appendix G] [1.5 x ($ )] / [1.8 x ( ) x ( /hr)]

=$ /hr


[1.5 x (TT Cost)] / [1.8 x (TT Wear Factor) x (Maximum Tire Life Hours)] [1.a.(9)(c)] [1.c.(9)(c)] [Appendix G]

[1.5 x ($ )] / [1.8 x ( ) x ( /hr)]

=$ /hr

(4) Total Tire Wear Cost: Total [5.e.] =$ /hr [Sum 5.e.(1) through 5.e.(3)]

f. Tire Repair Cost:

(Total Tire Wear Cost) x 0.15 x (LAF) [5.e.(4)] [Appendix B]

($ /hr) x 0.15 x ( ) Total [5.f.] =$ /hr

g. TOTAL HOURLY OPERATING COST: TOTAL [5.] =$ /hr [Sum 5.a. through 5.f.]


Page 5 of 6

EP 1110-1-8, Vol. 130 Nov 09

A-12


6. HOURLY RATES

a. Total Hourly Rate: [based on 40 hours per week (wk)] (Ownership Cost) + (Operating Cost)

($ /hr) + ($ /hr) =$ /hr

b. Other Work Shifts Hourly Rate: (Refer to Chapter 3, Adjustments to Rates, for methodology.) [(Depreciation) + [(FCCM) x (40 hr/wk) / (Work hr/wk)] + (Operating Cost)] [4.a.(2)] [4.b.(2)] (example: 60 hr/wk) [5.g.] [($ /hr) + [($ /hr) x (40 hr/wk) / ( hr/wk)] + ($ /hr)] =$ /hr

c. Standby Hourly Rate:

[(Depreciation) x 0.50] + (FCCM) [4.a.(2)] [4.b.(2)]

[($ /hr) x 0.50] + ($ /hr) =$ /hr)


Page 6 of 6

EP 1110-1-8, Vol. 130 Nov 09

A-13


EP 1110-1-8, Vol. 130 Nov 09

A-14

APPENDIX B AREA FACTORS

EP 1110-1-8, Vol. 130 Nov 09

B-1

APPENDIX B

Region: 1NORTHEAST

AREA FACTORS

EP 1110-1-8(Vol. 1)

7/31/2009

Total State Sales or Import Tax Rate: 5.80%Working Hours Per Year (WHPY): 1,360

Labor Adjustment Factor (LAF): 1.12

Electricity Cost Per Kilowatt-Hour: $0.142

Gasoline Cost Per Gallon: $3.01Diesel Cost Per Gallon (Off-Road Use): $3.17Diesel Cost Per Gallon (On-Road Use): $3.71Cost-of-Money Rate (Full Rate): 4.875%

Cost-of-Money Rate (Adjusted): 3.900%

over 240cwt thru $17.42





over 800cwt thru $6.15cwt thru $9.14

240300400500700800

99,999

over 0

Freight Rates

hrs/yr

/kW-Hr

/gal

/gal/gal

B-1

EP 1110-1-8, Vol. 130 Nov 09

B-2

APPENDIX B

Below is a listing of all regional area factors for reference only. The area factor's used for this pamphlet are located on previous page B-1.

EP 1110-1-8

7/31/2009(Vol. *) AREA FACTORS (for all regions)

Freight Cost

Reg SST WHPY LAF Elec Gas D-Off D-On Thru CWT $ Thru CWT $ Thru CWT $ Thru CWT $ Thru CWT $ Thru CWT $ Thru CWT $

1 NORTHEAST 2009 5.80% 1360 1.12 $0.142 $3.01 $3.17 $3.71 240 $17.42 300 $16.01 400 $13.92 500 $11.96 700 $6.15 800 $6.15 99,999 $9.14

2 MIDEAST 2009 5.80% 1450 1.02 $0.094 $2.96 $3.04 $3.59 240 $9.19 300 $8.46 400 $7.61 500 $6.83 700 $4.13 800 $4.13 99,999 $6.14

3 SOUTHEAST 2009 8.50% 1530 0.86 $0.089 $2.95 $3.04 $3.49 240 $14.96 300 $13.61 400 $11.62 500 $9.72 700 $5.42 800 $5.42 99,999 $8.01

4 NORTHCENTRAL 2009 5.85% 1260 1.02 $0.078 $2.88 $3.04 $3.55 240 $16.66 300 $15.38 400 $13.63 500 $12.03 700 $6.41 800 $5.88 99,999 $4.50

5 MIDWEST 2009 7.90% 1400 0.97 $0.075 $2.80 $3.04 $3.53 240 $13.06 300 $12.00 400 $10.42 500 $8.98 700 $5.30 800 $4.91 99,999 $3.75

6 SOUTHWEST 2009 8.10% 1590 0.86 $0.092 $2.83 $3.03 $3.46 240 $16.78 300 $15.67 400 $14.08 500 $12.63 700 $6.60 800 $6.08 99,999 $4.72

7 WEST 2009 8.50% 1630 1.14 $0.097 $3.17 $2.92 $3.44 240 $26.94 300 $25.13 400 $22.50 500 $20.06 700 $9.71 800 $8.53 99,999 $6.26

8 NORTHWEST 2009 6.00% 1540 1.01 $0.067 $3.13 $2.87 $3.41 240 $27.78 300 $26.06 400 $23.69 500 $21.52 700 $11.26 800 $9.51 99,999 $6.48

9 ALASKA 2009 1.50% 1040 1.19 $0.132 $3.65 $4.17 $4.42 240 $44.02 300 $41.59 400 $38.40 500 $35.48 700 $27.35 800 $25.43 99,999 $22.10

10 HAWAII 2009 4.50% 1480 1.24 $0.231 $3.72 $2.86 $3.57 240 $95.58 300 $76.59 400 $56.76 500 $62.17 700 $57.01 800 $44.76 99,999 $30.94

11 PUERTO RICO 2009 7.00% 1560 0.72 $0.139 $2.78 $3.05 $3.52 240 $48.22 300 $39.44 400 $28.83 500 $26.32 700 $19.36 800 $16.06 99,999 $12.91

12 KWAJALEIN 2009 4.50% 1390 1.05 $0.139 $3.01 $2.86 $3.57 240 $29.97 300 $27.88 400 $24.94 500 $22.21 700 $12.23 800 $10.61 99,999 $8.09

B- 2SST = State Sales tax WHPY = Work Hours Per Year LAF = Labor Adjustment Factor Elec = Electricty Cost Per kW-Hr Gas = Gasoline Cost per Gal D-Off = Diesel-Off Road Cost per Gal D-On = Diesel-On Road Cost per Gal CWT = Hundred Pounds

EP 1110-1-8, Vol. 130 Nov 09

B-3


EP 1110-1-8, Vol. 130 Nov 09

B-4

APPENDIX C GUIDE FOR SELECTING OPERATING CONDITIONS

EP 1110-1-8, Vol. 130 Nov 09

C-1


EQUIPMENT TYPE AVERAGE SEVERE B25 and B35: Buckets Clamshell or Dragline Depreciation Period:

Working in gravels, silts, and sands at low impact freshwater environment. 8,000 - 10,000 hours

Working in rock, hard digging, high impact, or saltwater environment. 6,500 - 8,000 hours

C80 and C90: Cranes Hydraulic, Truck Mounted

Mechanical, Truck Mounted

Depreciation Period:

Lift less than rated capacity, intermittent duty. 14,000 - 20,000 hours

Continuous lift near rated capacity, excessive swing, abrasive materials, sloped surfaces, and saltwater environment. 12,000 - 18,000 hours

C85: Cranes Mechanical Dragline,

Lifting, or Clamshell Crawler Mounted Depreciation Period:

Gravels, silts, pull, and lift less than rated capacity. 14,000 - 22,000 hours

Highly abrasive materials, impact breakout, continuous load near rated capacity, and saltwater environment. 12,000 - 18,000 hours

G10: Generators Depreciation Period:

Working below rated capacity, good field conditions. 8,000 - 10,000 hours

Working at or above rated capacity, poor field conditions, such as saltwater. 7,000 - 8,000 hours

EP 1110-1-8, Vol. 130 Nov 09

C-2


EQUIPMENT TYPE AVERAGE SEVERE G15: Graders, Motor Depreciation Period:

Haul road maintenance; road construction, ditching; loose fill spreading; landforming, landleveling; summer road maintenance with medium to heavy winter snow removal; and elevating grader use. 14,500 hours

Maintenance of hard-packed roads with embedded rock; heavy fill spreading; ripping scarifying of asphalt or concrete; continuous high load factor; and high impact. 13,500 hours

H25: Hydraulic Excavators Crawler Mounted Depreciation Period:

Mass excavation or trenching where machine digs all the time in natural bed clay soils; some traveling and steady, full throttle operation; and most log loading operations.

8,500 - 19,000 hours

Continuous trenching or truck loading in rock or shot rock soils; large amount of travel over rough ground; machine continuously working on rock floor with constant high load factor and high impact; and saltwater environment. 7,000 – 15,000 hours

H30: Hydraulic Excavators Wheel Mounted Depreciation Period:

Continuous digging in sandy clay/sandy gravel, site development, and lumber yard applications. 8,000 - 10,000 hours

Continuous digging in rock/natural bed clay, high impact, using hammer, and working in forests or quarries. 6,500 - 8,000 hours

H35: Hydraulic Shovels Crawler Mounted

Continuous loading in well shot rock or fairly tight

Continuous loading in poorly shot rock, virgin, or

EP 1110-1-8, Vol. 130 Nov 09

C-3


EQUIPMENT TYPE AVERAGE SEVERE (nonelectric)

Depreciation Period:

bank. Good underfoot conditions: dry floor, little impact, or sliding on undercarriage.

14,000 - 18,000 hours

lightly blasted tight banks. Adverse underfoot conditions: rough floors, high impact sliding on undercarriage; and saltwater environment. 12,000 - 16,000 hours

L10: Land Clearing Equipment Depreciation Period:

Working in low impact conditions at or below rated capacity. 10,000 hours

High impact conditions working at or above rated capacity. 7,000 hours

L30: Loaders, Belt (conveyors) Depreciation Period:

Working below rated capacity, with intermittent service. 10,000 hours

Working at or above rated capacity with continuous service. 8,000 hours

L35: Loaders, Front End Crawler Type Depreciation Period:

Bank excavation, intermittent ripping, basement digging of natural bed clays, sands, silts, and gravels; some traveling; and steady full throttle operations. 10,000 hours

Loading shot rock, cobbles, glacial till, and caliche; steel millwork; high density materials in standard bucket; continuous work on rock surfaces; large amount of ripping of tight rock materials; high impact conditions; and saltwater environment. 8,000 hours

EP 1110-1-8, Vol. 130 Nov 09

C-4


EQUIPMENT TYPE AVERAGE SEVERE L40: Loaders, Front End Wheel Type (does not include skid steer and tool carriers) Depreciation Period:

Continuous truck loading from stockpile; low to medium density materials in properly sized bucket; hopper charging in low to medium rolling resistance; loading from bank in good digging; and load and carry on poor surfaces and slight adverse grades. 9,250 - 13,500 hours

Loading shot rock (large loaders); handling high density materials with counterweighted machine; steady loading from very tight banks; continuous work on rough or very soft surfaces; load and carry in hard digging; travel longer distances on poor surfaces with adverse grades and saltwater environment. 8,750 - 12,000 hours

L45 and L50: Loaders with Backhoe Crawler Type and Wheel Type Depreciation Period:

Utility applications in medium to heavy soil; occasional use of constant flow implements and dig depths to 3.05 meters (10 feet). 8,000 hours

Production applications or digging in rock; regular use of constant flow implements; and dig depths over 3.05 meters (10 feet). 6,000 hours

L60: Log Skidders Depreciation Period:

Continuous turning, steady skidding for medium distances with moderate decking. Good underfooting: dry floor with few stumps and gradual rolling terrain. 10,000 hours

Continuous turning, steady skidding for long distances with frequent decking; poor underfoot conditions: wet floor, steep slopes, and numerous stumps; and saltwater environment. 8,000 hours

EP 1110-1-8, Vol. 130 Nov 09

C-5


EQUIPMENT TYPE AVERAGE SEVERE M10 - .31 and .32: Clamshell dredges < 5 cy Amphibious Excavator Depreciation Period:

Gravel, silts, breakout force at less than capacity, freshwater conditions. 10,000 - 20,000 hours

Rock, abrasive materials, load at rated capacity, saltwater conditions. 9,000 - 18,000 hours

M10 - .51 and .53: Boats, Skiffs, Crew Boats, Work Boats, Survey Boats, and Launches Depreciation Period:

Freshwater applications, light waves, and steady to light use. 16,000 - 18,000 hours

Saltwater use, medium to high waves, heavy use. 13,000 - 15,000 hours

P35: Pipelayers Depreciation Period:

Typical pipelayer use in operating conditions ranging from very good to severe. 14,000 hours

Continuous use in deep mud or water or on rock surfaces. 11,500 hours

R10: Rippers and Bank Slopers Depreciation Period:

Light rock, medium breakout force required. 8,000 hours

Hard rock, excessive wear due to high breakout force. 6,500 hours

S10, S15, S20, and S25: Scrapers Self-Propelled Tractor Drawn Soil Stabilizers Depreciation Period:

Varying loading and haul road conditions; long and short hauls; adverse and favorable grades; some impact; and typical road-building use on a variety of jobs. 10,000 - 15,000 hours

High impact conditions, such as loading ripped rock; overloading, continuous high total resistance conditions; and rough haul roads. 8,000 - 13,500 hours

EP 1110-1-8, Vol. 130 Nov 09

C-6


EQUIPMENT TYPE AVERAGE SEVERE T15: Tractors Crawler (Dozer) Depreciation Period:

Production dozing in clays, sands, gravels, and talus rock. Push-loading scrapers, borrow pit ripping, most land clearing and skidding applications. Medium impact conditions. Production landfill work. 10,000 - 15,000 hours

Heavy rock ripping; tandem ripping; pushloading and dozing in hard rock; work on rock surfaces; continuous high impact conditions; and saltwater environment. 8,000 - 12,500 hours

T20: Tractors Wheel Type (Dozer) Depreciation Period:

Production dozing, push loading in clays, sands, silts, loose gravels; and shovel cleanup. 14,000 hours

Production dozing in rock; push loading in rocky, boulder strewn borrow pits; high impact conditions; and landfill compactor work. 13,000 hours

T30: Trenchers Chain and Wheel Type Depreciation Period:

Working in sands and silts below rated capacity of the machine. 8,000 hours

Working in gravels and abrasive materials at or above the rated capacity of the machine. 6,000 hours

T45 and T50: Truck Trailers Trucks, Highway Depreciation Period:

Varying loading and road conditions; and typical construction use on a variety of jobs. 8,000 - 12,000 hours

Consistently poor road conditions; and oversized loading equipment. 6,500 - 10,000 hours

EP 1110-1-8, Vol. 130 Nov 09

C-7


EQUIPMENT TYPE AVERAGE SEVERE T55 and T60: Truck, Off-Highway Trucks, Water, Off-Highway (Articulated and Rigid) Depreciation Period:

Varying load and haul road conditions; high rolling resistance and poor traction during part of the job; some adverse grades; some impact loads; and typical use in road building, dam construction, open-pit mining, etc. 12,000 - 20,000 hours

Continuous use on very poorly maintained haul roads, high rolling resistance, and poor traction; frequent adverse grades and high impact loads; and poorly matched loading equipment with continuous overloading. 10,000 - 18,000 hours

W10 and W15: Wagons Bottom Dump Rear Dump Chapter 1 Depreciation Period:

Varying load and haul road conditions; long and short hauls; high rolling resistance and poor traction during part of the job; some adverse grades; some impact; typical road building use in a variety of jobs; and dam construction, open-pit mining, etc. 12,000 hours

Continuous use on very poorly maintained haul roads, high rolling resistance, and poor traction; high impact conditions, such as loading ripped rock; frequent adverse grades and high impact loads; and poorly matched loading equipment with continuous overloading. 10,000 hours

EP 1110-1-8, Vol. 130 Nov 09

C-8

APPENDIX D EQUIPMENT HOURLY CALCULATION FACTORS

EP 1110-1-8, Vol. 130 Nov 09

D-1

CATEGORY

SUB DESCRIPTION EK C DC LIFE SLV D TT RCFDTFTGEHPF DGEHPF DGEFUEL FACTORS

EQUIPMENT

FUEL FACTORS

CARRIER FOG TIRE WEAR

FACTORS

EQUIPMENT HOURLY CALCULATION FACTORS

EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

A10 0.00 1AGGREGATE / CHIP SPREADERSA10 0.10 10 A B 8,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .102 .102 0.83 0.72 0.92 0.75 SELF-PROPELLEDA10 0.20 10 A B 6,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.73 0.00 0.82 0.60 TOWED & TAILGATEA15 0.00 1AIR COMPRESSORS, PORTABLEA15 0.10 5 A B 10,000 0.20 75 .750 .068 .036 0 .000 .000 .000 .477 .136 .119 0.66 0.00 0.73 0.75 ROTARY SCREWA15 0.20 5 A B 12,000 0.15 75 .750 .068 .036 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.65 SHOP TYPEA20 0.00 1AIR HOSE, TOOLS & EQUIPMENTA20 0.10 5 A B 3,500 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 1.50 AIR DRILL HOSEA20 0.20 5 A B 3,500 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 1.65 SANDBLAST HOSEA20 0.30 5 A B 6,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.96 0.84 1.07 1.50 SANDBLASTERS, BREAKERS, & MISC. AIR TOOLSA25 0.00 10 A B 6,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 0.96 0.63 1.07 0.85ASPHALT PAVING DISTRIBUTORSA30 0.00 1ASPHALT PAVERS & MISCELLANEOUS ROAD

EQUIPMENTA30 0.10 10 A B 8,000 0.15 70 .700 .063 .034 0 .000 .000 .000 .000 .136 .119 1.08 0.72 1.20 1.00 SELF PROPELLEDA30 0.20 10 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 1.08 0.00 1.20 0.80 TOWEDA30 0.30 10 A B 12,000 0.20 60 .600 .054 .029 13 .130 .012 .006 .000 .100 .100 1.08 0.71 1.20 0.55 SLURRY SEAL PAVERS (Cold mix)A30 0.40 10 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 1.08 0.71 1.20 0.80 MISCELLANEOUS ROAD EQUIPMENTA35 0.00 10 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 1.08 0.71 1.20 0.80ASPHALT PAVING KETTLESA40 0.00 10 A B 6,000 0.20 95 .950 .086 .045 0 .000 .000 .000 .000 .136 .119 1.08 0.71 1.20 1.00ASPHALT & CONCRETE MILLERS / PROFILERS /

PLANERS / ROTARY GRINDERSA45 0.00 10 A B 5,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 1.08 0.71 1.20 0.90ASPHALT RECYCLERS & SEALERSB10 0.00 1BATCH PLANTS, ASPHALT & CONCRETEB10 0.10 10 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.72 1.20 1.00 ASPHALT

D- 1EK=Economic Key (Appendix E) LIFE=Economic Life E=Electric Powered FT=Front Tire C=Operating Conditions (A=average, S=severe) SLV=Salvage Value G=Gas Powered DT=Drive Tire DC=Discount Code (B=basic 7.5%, S=special 15%) HPF=Horsepower Factor D=Diesel Powered TT=Trailing Tire RCF=Repair Cost Factor

EP 1110-1-8, Vol. 130 Nov 09

D-2

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

B10 0.20 10 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.71 1.20 1.00 CONCRETEB10 0.30 10 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.71 1.20 1.00 PUGMILLB15 0.00 95 A B 8,000 0.10 65 .650 .059 .031 13 .130 .012 .006 .000 .102 .119 0.96 0.63 1.07 0.80BROOMS, STREET SWEEPERS & FLUSHERSB20 0.00 95 A B 8,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 0.00 0.00 0.92 0.90BRUSH CHIPPERSB25 0.00 15 A B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70BUCKETS, CLAMSHELLB25 0.00 15 S B 6,500 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80BUCKETS, CLAMSHELLB30 0.00 1BUCKETS, CONCRETEB30 0.10 15 A B 8,000 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70 GENERAL PURPOSE, MANUAL TRIPB30 0.20 15 A B 8,000 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.75 LAYDOWNB30 0.30 15 A B 8,000 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80 LOWBOYB30 0.40 15 A B 8,000 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80 LOW SLUMPB35 0.00 1BUCKETS, DRAGLINEB35 0.10 15 A B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70 LIGHT WEIGHTB35 0.10 15 S B 6,500 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80 LIGHT WEIGHTB35 0.20 15 A B 9,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70 MEDIUM WEIGHTB35 0.20 15 S B 7,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80 MEDIUM WEIGHTB35 0.30 15 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70 HEAVY WEIGHTB35 0.30 15 S B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80 HEAVY WEIGHTC05 0.00 95 A B 2,000 0.10 90 .900 .081 .043 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 2.50CHAIN SAWSC10 0.00 1COMPACTORS, WALK-BEHIND OR REMOTE

CONTROLLERC10 0.10 95 A B 4,000 0.05 90 .900 .081 .043 0 .000 .000 .000 .477 .102 .102 0.00 0.00 0.00 1.20 COMPACTORS, RAMMERS / TAMPERS &

VIBRATORY PLATES


EP 1110-1-8, Vol. 130 Nov 09

D-3

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

C10 0.20 95 A B 4,000 0.15 90 .900 .081 .043 0 .000 .000 .000 .477 .102 .102 0.00 0.00 0.00 1.20 ROLLERS, VIBRATORYC15 0.00 1 ACONCRETE CLEANERS / ABRASIVE BLASTERSC15 0.10 95 A B 4,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.00 0.00 0.00 0.90 WALK BEHINDC15 0.20 95 A B 8,000 0.20 95 .950 .086 .045 50 .500 .045 .024 .000 .136 .119 0.72 0.66 0.79 0.90 TRUCK/TRAILER MOUNTEDC20 0.00 95 A B 4,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.96 0.63 1.07 0.70CONCRETE BUGGIESC25 0.00 1CONCRETE FINISHERS/SCREEDS/SPREADERSC25 0.10 95 A B 5,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.00 0.00 0.00 0.80 FINISHERS/TROWELSC25 0.20 95 A B 5,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.96 0.84 1.07 0.80 VIBRATORY SCREEDC25 0.25 95 A B 8,000 0.30 65 .650 .059 .031 0 .000 .000 .000 .000 .180 .160 0.96 0.84 1.07 0.60 VIBRATORY LASER SCREEDC25 0.30 95 A B 8,000 0.30 65 .650 .059 .031 0 .000 .000 .000 .000 .180 .160 0.96 0.84 1.07 0.60 MATERIAL/TOPPING SPREADERSC30 0.00 95 A B 5,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.00 0.00 0.00 0.90CONCRETE GRINDERSC35 0.00 95 A B 7,000 0.25 75 .750 .068 .036 0 .000 .000 .000 .477 .136 .119 0.96 0.86 1.07 0.90CONCRETE GUNITERS / SHOTCRETERSC40 0.00 95 A B 5,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.00 0.00 0.92 0.80CONCRETE MIXING UNITSC45 0.00 10 A B 6,000 0.20 75 .750 .068 .036 0 .000 .000 .000 .000 .136 .119 1.08 0.72 1.20 1.00CONCRETE PAVING MACHINESC55 0.00 95 A B 8,000 0.10 70 .700 .063 .034 10 .100 .009 .005 .477 .136 .119 0.96 0.86 1.07 1.00CONCRETE PUMPSC60 0.00 95 A B 6,000 0.10 90 .900 .081 .043 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 1.00CONCRETE SAWS (Add cost for sawblade wear)C65 0.00 5 A B 4,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 2.50CONCRETE VIBRATORSC70 0.00 1CRANES, GANTRY & STRADDLEC75 0.00 20 A B 14,000 0.15 75 .750 .068 .036 0 .000 .000 .000 .000 .136 .127 0.66 0.59 0.73 0.80CRANES, HYDRAULIC, SELF-PROPELLEDC80 0.00 1CRANES, HYDRAULIC, TRUCK MOUNTEDC80 0.01 20 A B 14,000 0.15 65 .650 .059 .031 10 .100 .009 .005 .000 .161 .153 0.66 0.58 0.73 0.60 UNDER 26 TONC80 0.01 20 S B 12,000 0.15 85 .850 .077 .041 13 .130 .012 .006 .000 .161 .153 0.18 0.14 0.20 0.65 UNDER 26 TONC80 0.02 20 A B 16,000 0.15 65 .650 .059 .031 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.70 26 TON THRU 65 TON


EP 1110-1-8, Vol. 130 Nov 09

D-4

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

C80 0.02 20 S B 14,000 0.15 85 .850 .077 .041 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.75 26 TON THRU 65 TONC80 0.03 20 A B 18,000 0.15 65 .650 .059 .031 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.80 66 TON THRU 125 TONC80 0.03 20 S B 16,000 0.15 85 .850 .077 .041 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.85 66 TON THRU 125 TONC80 0.04 20 A B 20,000 0.15 65 .650 .059 .031 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.90 OVER 125 TONC80 0.04 20 S B 18,000 0.15 85 .850 .077 .041 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.95 OVER 125 TONC85 0.00 1CRANES, MECHANICAL, LATTICE BOOM, CRAWLER

MOUNTEDC85 0.11 20 A B 14,000 0.20 55 .550 .050 .026 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.80 DRAGLINE, CLAMSHELL, 0 THRU 1.0 CYC85 0.11 20 S B 12,000 0.20 72 .720 .065 .034 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.90 DRAGLINE, CLAMSHELL, 0 THRU 1.0 CYC85 0.12 20 A B 16,000 0.20 55 .550 .050 .026 0 .000 .000 .000 .000 .144 .144 0.00 0.00 0.00 0.85 DRAGLINE, CLAMSHELL, OVER 1.0 CY THRU 2.5

CYC85 0.12 20 S B 13,000 0.20 72 .720 .065 .034 0 .000 .000 .000 .000 .144 .144 0.00 0.00 0.00 0.95 DRAGLINE, CLAMSHELL, OVER 1.0 CY THRU 2.5

CYC85 0.13 20 A B 18,000 0.20 55 .550 .050 .026 0 .000 .000 .000 .000 .093 .093 0.00 0.00 0.00 0.95 DRAGLINE, CLAMSHELL, OVER 2.5 CY THRU 5.0

CYC85 0.13 20 S B 15,000 0.20 72 .720 .065 .034 0 .000 .000 .000 .000 .093 .093 0.00 0.00 0.00 1.05 DRAGLINE, CLAMSHELL, OVER 2.5 CY THRU 5.0

CYC85 0.14 20 A B 20,000 0.20 55 .550 .050 .026 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 1.05 DRAGLINE, CLAMSHELL, OVER 5.0 CYC85 0.14 20 S B 16,000 0.20 72 .720 .065 .034 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 1.15 DRAGLINE, CLAMSHELL, OVER 5.0 CYC85 0.21 20 A B 16,000 0.20 40 .400 .036 .019 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.65 LIFTING, 0 THRU 25 TONC85 0.21 20 S B 13,000 0.20 52 .520 .047 .025 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.70 LIFTING, 0 THRU 25 TONC85 0.22 20 A B 18,000 0.20 40 .400 .036 .019 0 .000 .000 .000 .000 .085 .085 0.00 0.00 0.00 0.75 LIFTING, 26 TON THRU 50 TONC85 0.22 20 S B 15,000 0.20 52 .520 .047 .025 0 .000 .000 .000 .000 .085 .085 0.00 0.00 0.00 0.80 LIFTING, 26 TON THRU 50 TONC85 0.23 20 A B 20,000 0.15 40 .400 .036 .019 0 .000 .000 .000 .000 .093 .093 0.00 0.00 0.00 0.85 LIFTING, 51 TON THRU 150 TON


EP 1110-1-8, Vol. 130 Nov 09

D-5

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

C85 0.23 20 S B 16,000 0.15 52 .520 .047 .025 0 .000 .000 .000 .000 .093 .093 0.00 0.00 0.00 0.90 LIFTING, 51 TON THRU 150 TONC85 0.24 20 A B 22,000 0.15 40 .400 .036 .019 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.95 LIFTING, OVER 150 TONC85 0.24 20 S B 18,000 0.15 52 .520 .047 .025 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 1.00 LIFTING, OVER 150 TONC90 0.00 1CRANES, MECHANICAL, LATTICE BOOM, TRUCK

MOUNTEDC90 0.01 20 A B 14,000 0.15 50 .500 .045 .024 10 .100 .009 .005 .000 .161 .153 0.66 0.58 0.73 0.60 UNDER 26 TONC90 0.01 20 S B 12,000 0.15 65 .650 .059 .031 13 .130 .012 .006 .000 .161 .153 0.18 0.14 0.20 0.65 UNDER 26 TONC90 0.02 20 A B 16,000 0.15 50 .500 .045 .024 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.70 26 TON THRU 65 TONC90 0.02 20 S B 14,000 0.15 65 .650 .059 .031 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.75 26 TON THRU 65 TONC90 0.03 20 A B 18,000 0.20 50 .500 .045 .024 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.80 66 TON THRU 125 TONC90 0.03 20 S B 16,000 0.20 65 .650 .059 .031 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.85 66 TON THRU 125 TONC90 0.04 20 A B 20,000 0.20 50 .500 .045 .024 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.90 OVER 125 TONC90 0.04 20 S B 18,000 0.20 65 .650 .059 .031 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.95 OVER 125 TONC95 0.00 20 A B 18,000 0.20 65 .650 .059 .031 10 .100 .009 .005 .530 .127 .110 0.00 0.00 0.92 0.85CRANES, TOWERD10 0.00 1DRILLS, AIR/HYDRAULIC,CRWLR MTD,0" THRU 6.5"

DIA HOLE (Add cost for drill steel and bit wear)D10 0.10 25 A B 14,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 1.00 DRILLS, AIR TRACK (Add cost for drill steel and bit

wear)D10 0.20 25 A B 10,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 1.00 DRILLS, HYDRAULIC TRACK (Add cost for drill steel

and bit wear)D15 0.00 25 A B 10,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.90DRILLS, HORIZONTAL BORING & GROUND

PIERCING (Add cost for drill steel and bit wear)D20 0.00 25 A B 8,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .068 .102 0.00 0.00 0.00 0.85DRILLS, CORE, COLUMN MOUNTED (Add cost for

drill steel and bit wear)


EP 1110-1-8, Vol. 130 Nov 09

D-6

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

D25 0.00 25 A B 10,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .068 .102 0.00 0.00 0.92 1.00DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear)

D30 0.00 25 A B 10,000 0.25 80 .800 .072 .038 10 .100 .009 .005 .477 .136 .119 0.96 0.86 1.07 1.00DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear)

D35 0.00 1DRILLS, ROTARY BLASTHOLE (Add cost for drill steel and bit wear)

D35 0.11 25 A B 14,000 0.20 80 .800 .072 .038 10 .100 .009 .005 .005 .161 .161 0.00 0.00 0.00 1.00 DIESEL, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit wear)

D35 0.12 25 A B 18,000 0.20 80 .800 .072 .038 10 .100 .009 .005 .011 .136 .136 0.96 0.86 1.07 1.00 DIESEL, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear)

D35 0.21 25 A B 14,000 0.20 70 .700 .063 .034 10 .100 .009 .005 .530 .000 .000 0.00 0.00 0.00 0.55 ELECTRIC, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit wear)

D35 0.22 25 A B 18,000 0.20 70 .700 .063 .034 10 .100 .009 .005 .530 .000 .000 0.00 0.00 0.00 0.55 ELECTRIC, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear)

F10 0.00 95 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .102 .102 0.83 0.46 0.92 0.75FORK LIFTSG10 0.00 1GENERATOR SETSG10 0.10 30 A B 8,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.73 0.60 PORTABLEG10 0.10 30 S B 7,000 0.10 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.20 0.70 PORTABLEG10 0.20 30 A B 10,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.70 SKID MOUNTEDG10 0.20 30 S B 8,000 0.10 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.80 SKID MOUNTEDG15 0.00 35 A B 14,500 0.25 60 .600 .054 .029 0 .000 .000 .000 .000 .085 .144 0.83 0.54 0.92 0.75GRADERS, MOTORG15 0.00 35 S B 13,500 0.25 78 .780 .070 .037 0 .000 .000 .000 .000 .085 .144 0.27 0.16 0.30 0.85GRADERS, MOTORH10 0.00 95 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00HAMMERS, HYDRAULIC (Demolition tool) (Add cost

for point wear)H13 0.00 1HAZARDOUS/TOXIC WASTE EQUIPMENT


EP 1110-1-8, Vol. 130 Nov 09

D-7

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

H13 0.11 95 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .530 .102 .102 1.08 0.86 1.20 0.80 COMPACTORS (Compression force) 0 THRU 50 TONS

H13 0.12 95 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .530 .102 .102 1.08 0.86 1.20 0.90 COMPACTORS (Compression force) OVER 50 TONSH13 0.21 95 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .530 .102 .102 0.00 0.00 0.00 0.90 FILTER PRESSES, STATIONARYH13 0.22 95 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .530 .102 .102 0.66 0.59 0.73 0.80 FILTER PRESSES, MOBILEH13 0.30 95 A B 4,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .530 .000 .000 0.00 0.00 0.00 0.70 CENTRIFUGESH13 0.40 95 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 0.90 SHREDDERSH13 0.51 95 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.77 0.69 0.86 1.00 SOIL TREATMENT PLANT, MOBILEH13 0.61 95 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 1.00 SLUDGE PROCESSING EQUIP, SLUDGE

DISPENSERSH13 0.71 95 A B 4,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 1.00 WASTE HANDLING EQUIPMENT, DRUM HANDLINGH15 0.00 1HEATERS, SPACEH20 0.00 95 A B 9,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.80HOISTS & AIR WINCHESH25 0.00 1HYDRAULIC EXCAVATORS, CRAWLER MOUNTEDH25 0.10 65 A B 8,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.70 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS)H25 0.10 65 S B 7,000 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.80 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS)H25 0.11 65 A B 8,500 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.70 OVER 12,500 LBS THRU 40,000 LBSH25 0.11 65 S B 7,000 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.85 OVER 12,500 LBS THRU 40,000 LBSH25 0.12 65 A B 12,000 0.25 65 .600 .059 .031 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.80 OVER 40,000 LBS THRU 100,000 LBSH25 0.12 65 S B 10,000 0.25 85 .800 .077 .041 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.95 OVER 40,000 LBS THRU 100,000 LBSH25 0.13 65 A B 16,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .047 .047 0.00 0.00 0.00 1.00 OVER 100,000 LBS THRU 160,000 LBSH25 0.13 65 S B 13,500 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .047 .047 0.00 0.00 0.00 1.10 OVER 100,000 LBS THRU 160,000 LBSH25 0.14 65 A B 19,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .051 .051 0.00 0.00 0.00 1.10 OVER 160,000 LBS


EP 1110-1-8, Vol. 130 Nov 09

D-8

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

H25 0.14 65 S B 15,000 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .051 .051 0.00 0.00 0.00 1.25 OVER 160,000 LBSH25 0.21 95 A B 6,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.90 ATTACHMENTS, MOBILE SHEARSH25 0.22 95 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.80 ATTACHMENTS, MATERIAL HANDLINGH25 0.23 95 A B 6,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00 ATTACHMENTS, CONCRETE PULVERIZERSH25 0.24 95 A B 6,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00 ATTACHMENTS, COMPACTORSH30 0.00 1HYDRAULIC EXCAVATORS, WHEEL MOUNTEDH30 0.01 65 A B 8,000 0.25 60 .600 .054 .029 10 .100 .009 .005 .000 .149 .141 0.83 0.54 0.92 0.50 0 THRU 1.0 CYH30 0.01 65 S B 6,500 0.25 78 .780 .070 .037 13 .130 .012 .006 .000 .149 .141 0.25 0.15 0.28 0.55 0 THRU 1.0 CYH30 0.02 65 A B 10,000 0.25 60 .600 .054 .029 10 .100 .009 .005 .000 .149 .141 0.83 0.54 0.92 0.60 OVER 1.0 CYH30 0.02 65 S B 8,000 0.25 78 .780 .070 .037 13 .130 .012 .006 .000 .149 .141 0.25 0.15 0.28 0.65 OVER 1.0 CYH35 0.00 1HYDRAULIC SHOVELS, CRAWLER MOUNTEDH35 0.11 65 A B 14,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .047 .047 0.00 0.00 0.00 1.00 DIESEL, 0 CY THRU 5.0 CYH35 0.11 65 S B 12,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .047 .047 0.00 0.00 0.00 1.10 DIESEL, 0 CY THRU 5.0 CYH35 0.12 65 A B 16,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .051 .051 0.00 0.00 0.00 1.20 DIESEL, OVER 5.0 CYH35 0.12 65 S B 14,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .051 .051 0.00 0.00 0.00 1.30 DIESEL, OVER 5.0 CYH35 0.21 65 A B 18,000 0.20 50 .500 .045 .024 0 .000 .000 .000 .265 .000 .000 0.00 0.00 0.00 0.80 ELECTRIC, OVER 2.5 CYH35 0.21 65 S B 16,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .265 .000 .000 0.00 0.00 0.00 0.90 ELECTRIC, OVER 2.5 CYL10 0.00 70 A B 10,000 0.20 60 .600 .054 .029 10 .100 .009 .005 .000 .127 .110 0.83 0.54 0.92 0.90LAND CLEARING EQUIPMENTL10 0.00 70 S B 7,000 0.20 78 .780 .070 .037 13 .130 .012 .006 .000 .127 .110 0.25 0.15 0.28 1.00LAND CLEARING EQUIPMENTL15 0.00 95 A B 4,000 0.15 80 .800 .072 .038 13 .130 .012 .006 .477 .102 .102 0.59 0.30 0.66 0.70LANDSCAPING EQUIPMENTL20 0.00 1LIGHTING SETS, TRAILER MOUNTEDL20 0.10 95 A B 8,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .102 0.66 0.58 0.73 1.50 METALLIC VAPORL25 0.00 95 A B 8,000 0.20 85 .850 .077 .041 13 .130 .012 .006 .000 .102 .102 0.66 0.58 0.73 1.20LINE STRIPING EQUIPMENT


EP 1110-1-8, Vol. 130 Nov 09

D-9

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

L30 0.00 95 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .119 .119 0.66 0.58 0.73 1.00LOADERS, BELT (Conveyor belts) & ACCESSORIESL30 0.00 95 S B 8,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .477 .119 .119 0.21 0.16 0.23 1.10LOADERS, BELT (Conveyor belts) & ACCESSORIESL35 0.00 40 A B 10,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .170 .101 0.00 0.00 0.00 1.10LOADERS, FRONT END, CRAWLER TYPEL35 0.00 40 S B 8,000 0.20 91 .910 .082 .044 0 .000 .000 .000 .000 .170 .101 0.00 0.00 0.00 1.25LOADERS, FRONT END, CRAWLER TYPEL40 0.00 1LOADERS, FRONT END, WHEEL TYPEL40 0.11 45 A B 9,250 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .170 .111 0.83 0.54 0.92 0.70 ARTICULATED, 0 THRU 225 HPL40 0.11 45 S B 8,750 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .170 .111 0.25 0.15 0.28 0.80 ARTICULATED, 0 THRU 225 HPL40 0.12 45 A B 13,500 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .170 .080 0.83 0.54 0.92 0.70 ARTICULATED, OVER 225 HPL40 0.12 45 S B 12,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .170 .080 0.25 0.15 0.28 0.75 ARTICULATED, OVER 225 HPL40 0.20 45 A B 8,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .170 .111 0.57 0.29 0.63 0.80 SKID STEERL40 0.21 45 A B 4,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .170 .170 0.00 0.00 0.00 1.00 SKID STEER ATTACHMENTSL40 0.31 45 A B 10,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .170 .111 0.83 0.54 0.92 0.85 TOOL CARRIER & TELESCOPIC HANDLERS, 0

THRU 225 HPL40 0.31 45 S B 9,250 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .170 .111 0.25 0.15 0.28 0.90 TOOL CARRIER & TELESCOPIC HANDLERS, 0

THRU 225 HPL40 0.32 45 A B 12,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .170 .080 0.83 0.54 0.92 0.85 TOOL CARRIER & TELESCOPIC HANDLERS, OVER

225 HPL40 0.32 45 S B 10,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .000 .170 .080 0.25 0.15 0.28 0.90 TOOL CARRIER & TELESCOPIC HANDLERS, OVER

225 HPL45 0.00 40 A B 8,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .441 .524 0.00 0.00 0.00 1.35LOADERS / BACKHOE, CRAWLER TYPEL45 0.00 40 S B 6,000 0.20 91 .910 .082 .044 0 .000 .000 .000 .000 .441 .524 0.00 0.00 0.00 1.40LOADERS / BACKHOE, CRAWLER TYPEL50 0.00 45 A B 10,000 0.25 50 .500 .045 .024 0 .000 .000 .000 .000 .441 .441 0.83 0.54 0.92 0.80LOADERS / BACKHOE, WHEEL TYPEL50 0.00 45 S B 6,000 0.25 70 .700 .063 .034 0 .000 .000 .000 .000 .441 .441 0.25 0.15 0.28 0.85LOADERS / BACKHOE, WHEEL TYPEL55 0.00 95 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .441 .441 0.00 0.00 0.00 1.00LOADER / BACKHOE, ATTACHMENTS


EP 1110-1-8, Vol. 130 Nov 09

D-10

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

L60 0.00 75 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.83 0.54 0.92 0.70LOG SKIDDERSL60 0.00 75 S B 8,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .119 0.25 0.15 0.28 0.80LOG SKIDDERSM10 0.00 1MARINE EQUIPMENT (NON DREDGING)M10 0.11 105 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.70 AQUATIC MAINTENANCEM10 0.12 105 A B 6,000 0.20 80 .800 .072 .038 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.60 AQUATIC MAINTENANCE ATTACHMENTSM10 0.21 105 A B 16,000 0.10 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.70 HYDRAULIC CUTTERHEAD DREDGE, 8" OR

LESS,TRANSPORTABLEM10 0.22 105 A B 16,000 0.10 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.80 HYDRAULIC CUTTERHEAD DREDGE,8" -

12",TRANSPORTABLEM10 0.23 105 A B 16,000 0.10 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.80 HYDRAULIC AUGERHEAD DREDGE,12" OR

LESS,TRANSPORTABLEM10 0.24 105 A B 8,000 0.10 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.70 HYDRAULIC FLOATING PUMPS,12" OR

LESS,TRANSPORTABLEM10 0.25 105 A B 6,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.70 HYDRUALIC DREDGE PUMPS,12" OR

LESS,TRANSPORTABLEM10 0.26 105 A B 6,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.60 HYDRAULIC DREDGE / PUMP ATTACHMENTSM10 0.31 20 A B 18,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .102 .102 0.00 0.00 0.00 1.00 SMALL MECH DREDGES,CLAMSHELL,BARGE-MTD

TO 5 CYM10 0.31 20 S B 16,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .477 .102 .102 0.00 0.00 0.00 1.05 SMALL MECH DREDGES,CLAMSHELL,BARGE-MTD

TO 5 CYM10 0.32 65 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .161 .161 0.00 0.00 0.00 1.00 SMALL MECH DREDGES, AMPHIBIOUS

EXCAVATORSM10 0.32 65 S B 9,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .477 .161 .161 0.00 0.00 0.00 1.10 SMALL MECH DREDGES, AMPHIBIOUS

EXCAVATORSM10 0.33 105 A B 20,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.90 SMALL MECH DREDGES,HOE-MOUNTED

DREDGING ATTACH


EP 1110-1-8, Vol. 130 Nov 09

D-11

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

M10 0.41 105 A B 6,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.50 WORK FLOATS (NON-DREDGING)M10 0.42 105 A B 30,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.60 WORK BARGES (SECTIONAL, NON-DREDGING)M10 0.45 105 A B 90,000 0.05 20 .200 .018 .010 0 .000 .000 .000 .000 .000 .136 0.00 0.00 0.00 0.60 FLAT-DECK OR CARGO BARGE (NON-DREDGING)M10 0.46 105 A B 90,000 0.05 20 .200 .018 .010 0 .000 .000 .000 .000 .000 .136 0.00 0.00 0.00 0.70 DUMP SCOW (NON-DREDGING)M10 0.47 105 A B 30,000 0.05 20 .200 .018 .010 0 .000 .000 .000 .000 .000 .136 0.00 0.00 0.00 0.70 DRILL BARGE (NON-DREDGING)M10 0.48 105 A B 30,000 0.05 20 .200 .018 .010 0 .000 .000 .000 .000 .000 .136 0.00 0.00 0.00 0.70 ALL OTHER BARGES (NON-DREDGING)M10 0.51 105 A B 16,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 0.70 BOATS & LAUNCHES, 0 THRU 250 HPM10 0.51 105 S B 13,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 0.75 BOATS & LAUNCHES, 0 THRU 250 HPM10 0.53 105 A B 18,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 0.80 BOATS & LAUNCHES, 251 THRU 500 HPM10 0.53 105 S B 15,000 0.10 85 .850 .077 .041 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 0.85 BOATS & LAUNCHES, 251 THRU 500 HPM10 0.54 105 A B 40,000 0.10 60 .600 .054 .029 50 .500 .045 .024 .477 .136 .161 0.00 0.00 0.00 0.90 TUGS, 501 THRU 1,000 HPM10 0.55 105 A B 55,000 0.10 60 .600 .054 .029 50 .500 .045 .024 .477 .136 .161 0.00 0.00 0.00 1.00 TUGS, 1,000 THRU 2,000 HPP10 0.00 50 A B 6,000 0.35 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 0.00 0.00 0.00 0.80PILE HAMMER ACCESSORIES - EXTRACTORS &

BOX LEADSP20 0.00 1PILE HAMMERS, DOUBLE ACTINGP20 0.10 50 A B 6,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.10 DIESELP20 0.20 50 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.10 PNUEMATIC (STEAM/AIR)P25 0.00 1PILE HAMMERS, SINGLE ACTINGP25 0.10 50 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00 DIESELP25 0.20 50 A B 6,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00 PNUEMATIC (STEAM/AIR)P30 0.00 50 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 0.00 0.00 0.00 1.00PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORYP35 0.00 70 A B 14,000 0.20 35 .350 .032 .017 0 .000 .000 .000 .000 .000 .170 0.00 0.00 0.00 0.95PIPELAYERSP35 0.00 70 S B 11,500 0.20 46 .460 .041 .022 0 .000 .000 .000 .000 .000 .170 0.00 0.00 0.00 1.10PIPELAYERS


EP 1110-1-8, Vol. 130 Nov 09

D-12

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

P40 0.00 20 A B 8,000 0.10 50 .500 .045 .024 50 .500 .045 .024 .477 .136 .119 0.66 0.33 0.73 0.80PLATFORMS & MAN-LIFTSP45 0.00 95 A B 8,000 0.15 95 .950 .086 .045 0 .000 .000 .000 .477 .136 .119 0.66 0.59 0.73 1.00PUMPS, GROUTP50 0.00 1PUMPS, WATER, CENTRIFUGAL, TRASHP50 0.11 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.66 0.00 0.73 0.90 ENGINE DRIVEP50 0.12 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.66 0.00 0.73 0.50 ELECTRIC DRIVEP50 0.21 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.66 0.00 0.73 0.90 WHEEL MOUNTED, ENGINE DRIVEP50 0.22 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.66 0.00 0.73 0.50 WHEEL MOUNTED, ELECTRIC DRIVEP50 0.31 95 A B 4,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 1.50 HOSES, PUMP, SUCTION & DISCHARGEP55 0.00 1PUMPS, WATER, SUBMERSIBLEP55 0.01 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.00 1.00 ENGINE DRIVEP55 0.02 95 A B 8,000 0.15 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.00 0.00 0.00 0.60 ELECTRIC DRIVEP60 0.00 1PUMPS, WATER, CENTRIFUGAL, DEWATERINGP60 0.11 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.00 0.90 SKID MOUNTED, ENGINE DRIVEP60 0.12 95 A B 8,000 0.15 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.00 0.00 0.00 0.50 SKID MOUNTED, ELECTRIC DRIVEP60 0.21 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.73 0.90 WHEEL MOUNTED, ENGINE DRIVEP60 0.22 95 A B 8,000 0.15 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.00 0.00 0.73 0.50 WHEEL MOUNTED, ELECTRIC DRIVEP65 0.00 1PUMPS, WATER, DIAPHRAGMP65 0.11 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.00 0.90 SKID MOUNTED, ENGINE DRIVEP65 0.12 95 A B 8,000 0.15 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.00 0.00 0.00 0.50 SKID MOUNTED, ELECTRIC DRIVEP65 0.21 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.73 0.80 WHEEL MOUNTED, ENGINE DRIVEP65 0.22 95 A B 8,000 0.15 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.00 0.00 0.73 0.40 WHEEL MOUNTED, ELECTRIC DRIVEP70 0.00 1PUMPS, WATER (For core drills)P70 0.01 95 A B 8,000 0.25 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.00 0.80 ENGINE DRIVE


EP 1110-1-8, Vol. 130 Nov 09

D-13

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

P70 0.02 95 A B 8,000 0.25 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.00 0.00 0.00 0.40 ELECTRIC DRIVER10 0.00 70 A B 8,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.90RIPPERS & HYDRAULIC BANK SLOPERS (Add cost

for point wear)R10 0.00 70 S B 6,500 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 1.00RIPPERS & HYDRAULIC BANK SLOPERS (Add cost

for point wear)R15 0.00 55 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.92 0.70ROLLERS, STATIC, TOWED, PNEUMATICR20 0.00 55 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.92 0.80ROLLERS, STATIC, TOWED, STEEL DRUMR30 0.00 1ROLLERS, STATIC, SELF-PROPELLED R30 0.01 55 A B 8,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .000 .102 .102 0.83 0.54 0.92 0.70 PNEUMATICR30 0.02 55 A B 10,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.80 SMOOTH DRUMR30 0.03 55 A B 12,000 0.20 80 .800 .072 .038 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.80 TAMPING FOOT, LANDFILL & SOIL COMPACTORSR40 0.00 55 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.80ROLLERS, VIBRATORY, TOWEDR45 0.00 55 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.10ROLLERS, VIBRATORY, SELF-PROPELLED,

DOUBLE DRUMR50 0.00 55 A B 8,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.83 0.54 0.92 1.00ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE

DRUMR55 0.00 95 A B 6,000 0.15 60 .600 .054 .029 0 .000 .000 .000 .477 .102 .102 0.97 0.87 1.08 0.80ROOFING EQUIPMENTS10 0.00 1SCRAPERS, ELEVATINGS10 0.01 60 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .000 .170 0.84 0.55 0.93 0.90 0 THRU 200 HPS10 0.01 60 S B 8,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .000 .170 0.23 0.13 0.25 1.00 0 THRU 200 HPS10 0.02 60 A B 13,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .000 .136 0.84 0.55 0.93 0.95 OVER 200 HPS10 0.02 60 S B 11,500 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .000 .136 0.23 0.13 0.25 1.00 OVER 200 HPS15 0.00 60 A B 15,000 0.20 60 .600 .054 .029 0 .000 .000 .000 .000 .000 .136 0.84 0.55 0.93 0.80SCRAPERS, CONVENTIONALS15 0.00 60 S B 12,500 0.20 78 .780 .070 .037 0 .000 .000 .000 .000 .000 .136 0.23 0.13 0.25 0.85SCRAPERS, CONVENTIONAL


EP 1110-1-8, Vol. 130 Nov 09

D-14

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

S20 0.00 60 A B 15,000 0.20 62 .620 .056 .030 62 .620 .056 .030 .000 .000 .110 0.84 0.55 0.93 0.85SCRAPERS, TANDEM POWEREDS20 0.00 60 S B 13,500 0.20 81 .810 .073 .039 81 .810 .073 .039 .000 .000 .110 0.23 0.13 0.25 0.90SCRAPERS, TANDEM POWEREDS25 0.00 60 A B 12,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.84 0.55 0.93 0.70SCRAPERS, TRACTOR DRAWNS25 0.00 60 S B 10,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.23 0.13 0.25 0.75SCRAPERS, TRACTOR DRAWNS30 0.00 1SCREENING & CRUSHING PLANTSS30 0.10 95 A B 10,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 0.70 CONVEYORSS30 0.10 95 S B 8,000 0.10 78 .780 .070 .037 0 .000 .000 .000 .577 .163 .142 0.96 0.72 1.07 0.85 CONVEYORSS30 0.20 95 A B 25,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 1.00 CRUSHERS - VERTICAL & HORIZONTAL SHAFT

IMPACTORS30 0.20 95 S B 15,000 0.10 78 .780 .070 .037 0 .000 .000 .000 .577 .163 .142 0.96 0.72 1.07 1.25 CRUSHERS - VERTICAL & HORIZONTAL SHAFT

IMPACTORS30 0.21 95 A B 25,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 1.20 CRUSHERS - CONES30 0.21 95 S B 15,000 0.10 78 .780 .070 .037 0 .000 .000 .000 .577 .163 .142 0.96 0.72 1.07 1.60 CRUSHERS - CONES30 0.22 95 A B 25,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 0.65 CRUSHERS - JAWS30 0.22 95 S B 15,000 0.10 78 .780 .070 .037 0 .000 .000 .000 .577 .163 .142 0.96 0.72 1.07 0.85 CRUSHERS - JAWS30 0.30 95 A B 10,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 0.80 SCREENING PLANTS30 0.30 95 S B 8,000 0.10 78 .780 .070 .037 0 .000 .000 .000 .577 .163 .142 0.96 0.72 1.07 1.00 SCREENING PLANTS35 0.00 95 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .000 .119 0.00 0.00 0.00 0.80SNOW REMOVAL EQUIPMENTS40 0.00 60 A B 10,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .000 .119 0.84 0.55 0.96 0.85SOIL & ROAD STABILIZERSS40 0.00 60 S B 8,000 0.20 91 .910 .082 .044 0 .000 .000 .000 .000 .000 .119 0.23 0.13 0.25 0.95SOIL & ROAD STABILIZERSS45 0.00 95 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00SPLITTERS, ROCK & CONCRETET10 0.00 70 A B 10,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.96 0.80TRACTOR BLADES & ATTACHMENTS (including

agricultural)


EP 1110-1-8, Vol. 130 Nov 09

D-15

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

T10 0.00 70 S B 8,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.86 0.90TRACTOR BLADES & ATTACHMENTS (including agricultural)

T15 0.00 1TRACTORS, CRAWLER (DOZER) (includes blade)T15 0.01 70 A B 10,000 0.30 70 .700 .063 .034 0 .000 .000 .000 .000 .000 .153 0.00 0.00 0.00 1.10 0 THRU 225 HPT15 0.01 70 S B 8,000 0.30 91 .910 .082 .044 0 .000 .000 .000 .000 .000 .153 0.00 0.00 0.00 1.25 0 THRU 225 HPT15 0.02 70 A B 12,500 0.25 70 .700 .063 .034 0 .000 .000 .000 .000 .000 .119 0.00 0.00 0.00 1.20 226 HP THRU 425 HPT15 0.02 70 S B 10,500 0.25 91 .910 .082 .044 0 .000 .000 .000 .000 .000 .119 0.00 0.00 0.00 1.25 226 HP THRU 425 HPT15 0.03 70 A B 15,000 0.20 60 .600 .054 .029 0 .000 .000 .000 .000 .000 .066 0.00 0.00 0.00 1.20 OVER 425 HPT15 0.03 70 S B 12,500 0.20 78 .780 .070 .037 0 .000 .000 .000 .000 .000 .066 0.00 0.00 0.00 1.35 OVER 425 HPT20 0.00 75 A B 14,000 0.15 60 .600 .054 .029 0 .000 .000 .000 .000 .102 .119 0.96 0.63 0.00 0.60TRACTORS, WHEEL TYPE (DOZER)T20 0.00 75 S B 13,000 0.15 78 .780 .070 .037 0 .000 .000 .000 .000 .102 .119 0.25 0.15 0.00 0.65TRACTORS, WHEEL TYPE (DOZER)T25 0.00 1TRACTORS, AGRICULTURALT25 0.10 75 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.00 0.00 0.00 0.85 CRAWLERT25 0.20 75 A B 8,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.96 0.73 0.00 0.70 WHEELT30 0.00 80 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .119 .119 1.08 0.82 0.00 0.90TRENCHERS, CHAIN TYPE CUTTERT30 0.00 80 S B 6,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .119 .119 0.32 0.22 0.00 1.00TRENCHERS, CHAIN TYPE CUTTERT35 0.00 80 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .119 .119 1.08 0.82 0.00 0.90TRENCHERS, WHEEL TYPE CUTTERT35 0.00 80 S B 6,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .119 .119 0.32 0.22 0.00 1.00TRENCHERS, WHEEL TYPE CUTTERT40 0.00 1TRUCK OPTIONST40 0.10 95 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 0.00 0.00 0.00 0.80 CRANES / HOISTS, PERSONNEL & MATERIAL

HANDLINGT40 0.20 95 A B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70 DUMP BODY, REART40 0.20 95 S B 6,500 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80 DUMP BODY, REAR


EP 1110-1-8, Vol. 130 Nov 09

D-16

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

T40 0.30 95 A B 8,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.60 FLATBEDS, WITH SIDEST40 0.41 95 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 0.00 0.00 0.00 0.70 HOIST, ELECTRIC DRIVET40 0.50 95 A B 8,000 0.15 65 .650 .059 .031 35 .350 .032 .017 .477 .136 .136 0.77 0.69 0.86 0.70 TRANSIT MIXERST40 0.60 95 A B 8,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 0.00 0.00 0.00 0.60 WATER TANKST40 0.70 95 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 1.08 0.86 1.20 0.70 ALL OTHER OPTIONST45 0.00 1TRUCK TRAILERST45 0.10 95 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.70 BOTTOM DUMPT45 0.10 95 S B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.18 0.00 0.20 0.80 BOTTOM DUMPT45 0.20 95 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.65 END DUMPT45 0.20 95 S B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.18 0.00 0.20 0.75 END DUMPT45 0.30 95 A B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.60 PUP TRAILERT45 0.41 95 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.50 LOWBOY, RIGID NECK, DROP DECKT45 0.50 95 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.50 FLATBED TRAILERT45 0.60 95 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.50 MISCELLANEOUS / UTILITYT45 0.70 95 A B 10,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .119 .102 0.66 0.92 0.73 0.60 WATER TANKER TRAILERT45 0.80 95 A B 8,000 0.25 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.70 DECONTAMINATION FACILITYT45 0.90 95 A B 10,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .119 .102 0.66 0.00 0.73 0.70 TANK TRAILERST50 0.00 1TRUCKS, HIGHWAY (Add attachments as required)T50 0.01 85 A S 8,000 0.20 15 .150 .014 .007 0 .000 .000 .000 .000 .119 .102 0.61 0.56 0.67 0.70 0 THRU 10,000 GVWT50 0.01 85 S S 6,500 0.20 20 .200 .018 .010 0 .000 .000 .000 .000 .119 .102 0.20 0.16 0.22 0.75 0 THRU 10,000 GVWT50 0.02 85 A S 10,000 0.20 35 .350 .032 .017 0 .000 .000 .000 .000 .127 .110 0.72 0.66 0.79 0.65 OVER 10,000 THRU 30,000 GVW (Chassis only - Add

options)


EP 1110-1-8, Vol. 130 Nov 09

D-17

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

T50 0.02 85 S S 8,000 0.20 46 .460 .041 .022 0 .000 .000 .000 .000 .127 .110 0.20 0.16 0.22 0.70 OVER 10,000 THRU 30,000 GVW (Chassis only - Add options)

T50 0.03 85 A S 12,000 0.20 50 .500 .045 .024 0 .000 .000 .000 .000 .136 .119 0.77 0.71 0.86 0.65 OVER 30,000 GVW (Chassis only - Add options)T50 0.03 85 S S 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 0.21 0.18 0.24 0.75 OVER 30,000 GVW (Chassis only - Add options)T55 0.00 1TRUCKS, OFF-HIGHWAYT55 0.10 90 A B 20,000 0.15 35 .350 .032 .017 0 .000 .000 .000 .000 .000 .144 0.84 0.73 0.93 0.90 RIGID FRAMET55 0.10 90 S B 18,000 0.15 45 .450 .041 .022 0 .000 .000 .000 .000 .000 .144 0.23 0.18 0.25 0.95 RIGID FRAMET55 0.20 90 A B 13,000 0.15 50 .500 .045 .024 0 .000 .000 .000 .000 .000 .080 0.84 0.73 0.93 0.80 ARTICULATED FRAMET55 0.20 90 S B 12,250 0.15 60 .600 .054 .029 0 .000 .000 .000 .000 .000 .080 0.23 0.18 0.25 0.85 ARTICULATED FRAMET56 0.00 1TRUCKS,OFF-HIGHWAY/PRIME MOVER TRACTORS

& WAGONST56 0.10 90 A B 20,000 0.15 40 .400 .036 .019 0 .000 .000 .000 .000 .102 .144 0.84 0.64 0.93 0.90 PRIME MOVER TRACTORST56 0.10 90 S B 18,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.23 0.16 0.25 0.95 PRIME MOVER TRACTORST56 0.20 90 A B 15,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.84 0.64 0.93 0.65 WAGONS, BOTTOM DUMPT56 0.20 90 S B 10,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .136 0.23 0.16 0.25 0.75 WAGONS, BOTTOM DUMPT56 0.30 90 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.84 0.65 0.93 0.60 WAGONS, REAR DUMPT57 0.00 95 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.23 0.17 0.25 0.80TRUCKS, VACUUMT60 0.00 90 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.90 0.69 1.00 0.70TRUCKS, WATER, OFF-HIGHWAYT60 0.00 90 S B 10,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .136 0.25 0.17 0.28 0.80TRUCKS, WATER, OFF-HIGHWAYT65 0.00 1TUNNEL/MINING EQUIPMENTT65 0.10 25 A B 14,000 0.15 80 .800 .072 .038 13 .130 .012 .006 .530 .136 .119 0.67 0.57 0.00 0.90 DRIFTING & TUNNELING DRILLST65 0.20 95 A B 18,000 0.15 70 .700 .063 .034 0 .000 .000 .000 .530 .000 .000 0.00 0.00 0.00 0.70 TUNNEL BORING MACHINEST65 0.20 95 S B 16,000 0.15 91 .910 .082 .044 0 .000 .000 .000 .530 .000 .000 0.00 0.00 0.00 0.80 TUNNEL BORING MACHINES


EP 1110-1-8, Vol. 130 Nov 09

D-18

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

T65 0.30 25 A B 12,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .530 .136 .119 0.00 0.00 0.00 0.90 PRODUCTION DRILLING RIGST65 0.40 95 A B 16,000 0.15 70 .700 .063 .034 0 .000 .000 .000 .530 .000 .000 0.00 0.00 0.00 0.90 ROADHEADERS & CONTINUOUS MINERST65 0.40 95 S B 14,000 0.15 91 .910 .082 .044 0 .000 .000 .000 .530 .000 .000 0.00 0.00 0.00 1.00 ROADHEADERS & CONTINUOUS MINERST65 0.50 95 A B 10,000 0.20 80 .800 .072 .038 10 .100 .009 .005 .530 .136 .119 0.00 0.00 0.00 0.80 ROCK BOLTING EQUIPMENTT65 0.61 95 A B 12,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .136 .127 0.00 0.00 0.00 0.75 LOADING & HAULING EQUIPMENT, DIESEL OR

GAST65 0.62 95 A B 14,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .477 .102 .102 0.00 0.00 0.00 0.70 LOADING & HAULING EQUIPMENT, ELECTRICT65 0.63 95 A B 10,000 0.25 70 .700 .063 .034 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.65 LOADING & HAULING EQUIPMENT, AIR-POWEREDT65 0.70 95 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.75 LOCOMOTIVEST65 0.90 95 A B 10,000 0.20 70 .700 .063 .034 13 .130 .012 .006 .477 .136 .127 0.00 0.00 0.00 0.80 OTHER TUNNELING EQUIPMENTW10 0.00 90 A B 12,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.88 0.67 0.98 0.65WAGONS, BOTTOM DUMPW10 0.00 90 S B 10,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .136 0.25 0.17 0.28 0.75WAGONS, BOTTOM DUMPW15 0.00 90 A B 12,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.88 0.77 0.98 0.60WAGONS, REAR DUMPW15 0.00 90 S B 10,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .136 0.25 0.19 0.28 0.70WAGONS, REAR DUMPW25 0.00 1WATER & CO2 BLASTERSW25 0.10 95 A B 4,000 0.20 95 .950 .086 .045 0 .000 .000 .000 .424 .102 .119 0.96 0.73 1.07 1.10 LOW PRESSURE, (< 5,000 PSI)W25 0.20 95 A B 4,000 0.20 95 .950 .086 .045 0 .000 .000 .000 .424 .102 .119 0.96 0.73 1.07 1.20 HIGH PRESSURE, (>= 5,000 PSI)W25 0.30 95 A B 4,000 0.20 95 .950 .086 .045 0 .000 .000 .000 .424 .102 .119 0.00 0.00 0.73 1.10 STEAM CLEANERSW25 0.40 95 A B 6,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .127 .148 0.00 0.00 0.73 1.00 CO2 BLASTERSW25 0.50 95 A B 10,000 0.35 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.73 0.40 WET ABRASIVE BLASTING SYSTEM (TORBO)W30 0.00 1WATER TANKSW30 0.10 90 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.00 0.00 0.73 0.60 PORTABLE WITH WHEELSW30 0.20 90 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.00 0.00 0.00 0.50 SKID MOUNTED


EP 1110-1-8, Vol. 130 Nov 09

D-19

CATEGORY


EQUIPMENT

FUEL FACTORS


FACTORS


EP 1110-1-8

7/31/2009#Error

FACTORS

APPENDIX D

W35 0.00 1WELDERSW35 0.10 95 A B 8,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .000 .102 .102 0.00 0.00 1.07 0.75 ENGINE DRIVENW35 0.20 95 A B 6,000 0.20 30 .300 .027 .014 0 .000 .000 .000 .424 .000 .000 0.00 0.00 0.00 0.50 ELECTRIC DRIVEN


EP 1110-1-8, Vol. 130 Nov 09

D-20

APPENDIX E ECONOMIC INDEXES FOR CONSTRUCTION EQUIPMENT

EP 1110-1-8, Vol. 130 Nov 09

E-1

1995 1994 19932010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998 1997 1996

KEY

EQUIPMENT DIVISIONS

ECONOMIC INDEXES FOR CONSTRUCTION EQUIPMENT

(EK)

Note: Table 2-1 Equipment Rates are based on equipment purchased new in the year 2006

2011

{--Projected---------}

EP 1110-1-8

7/31/2009

APPENDIX E

(Vol. 12)

2655 245726025 Air Equipment 2319 2234 2157 2085 2075 2069 2079 2047 2078 2074 2070 2063 2053 2012 20222714

4653 4381455710 Asphalt & Concrete Paving Equipment 4228 4116 3950 3758 3763 3769 3766 3717 3638 3589 3490 3390 3323 3248 31894756

9158 8687897215 Buckets 8604 8502 8057 7626 7443 7254 6804 6900 6982 6930 6888 6774 6672 6638 66639362

7048 6685690520 Cranes, Draglines & Clamshells - Crawler & Truck Mtd 6621 6543 6201 5869 5728 5582 5236 5310 5289 5225 5116 5013 4880 4783 47367205

6137 5783601725 Drills 5448 5104 4762 4444 4192 4116 3819 3736 3683 3626 3574 3518 3394 3320 32686273

5966 5623583930 Generators 5357 5112 4888 4641 4566 4548 4548 4529 4520 4517 4484 4511 4457 4343 42946099

7613 7152745135 Graders, Motor 6909 6825 6578 6318 6117 6049 5979 5952 5853 5682 5544 5466 5186 5088 49467782

7810 7259763640 Loaders, Track 7037 6907 6653 6347 6177 6081 6058 6032 5960 5792 5686 5606 5434 5257 50687984

7208 6699704745 Loaders, Wheel 6494 6374 6140 5857 5701 5612 5591 5567 5511 5409 5303 5251 5101 4988 48947368

6789 6377664750 Pile Driving Equipment 6176 6033 5787 5450 5270 5195 5127 5112 5062 4993 4892 4809 4700 4598 45396939

7191 6736705055 Rollers 6424 6145 5872 5646 5406 5285 5225 5130 5204 5092 5001 4950 4851 4719 44847351

7613 7152745160 Scrapers & Soil Stabilizers 6909 6825 6578 6318 6117 6049 5979 5952 5853 5682 5544 5466 5186 5088 49467782

7048 6685690565 Shovels, Backhoes & Hydraulic Excavators 6621 6543 6201 5869 5728 5582 5236 5310 5289 5225 5116 5013 4880 4783 47367205

7810 7259763670 Tractors, Crawlers & Attachments 7037 6907 6653 6347 6177 6081 6058 6032 5960 5792 5686 5606 5434 5257 50687984

6877 6442674275 Tractor, Wheel 6144 5876 5616 5400 5170 5055 4997 4906 4833 4695 4624 4540 4527 4484 43427030

8877 8314870280 Trenchers 7930 7584 7248 6970 6466 6524 6450 6332 6223 6042 5833 5749 5670 5509 52079074

5449 5122533485 Trucks, Highway 4965 4820 4638 4450 4356 4306 4216 4212 4307 4216 4241 4318 4293 4190 40255570

7999 7650784490 Trucks & Wagons - Off-Highway 7392 7231 6896 6424 6095 6026 5931 5828 5715 5651 5581 5440 5265 4979 48378177

6789 6377664795 All Other Equipment 6176 6033 5787 5450 5270 5195 5127 5112 5062 4993 4892 4809 4700 4598 45396939

3440 32673382100 All Tires & Tubes 3025 2926 2759 2614 2487 2430 2401 2373 2371 2400 2431 2475 2559 2517 25253516

7926 74607762105 Marine Equipment 7202 6905 6661 6436 6101 5846 5771 5645 5556 5513 5429 5245 5036 4951 48818102

EK = Economic Key E-1

EP 1110-1-8, Vol. 130 Nov 09

E-2

1977 1976 19751992 1991 1990 1989 1988 1987 1986 1985 1984 1983 1982 1981 1980 1979 1978

KEY

EQUIPMENT DIVISIONS

ECONOMIC INDEXES FOR CONSTRUCTION EQUIPMENT

(EK)

Note: Table 2-1 Equipment Rates are based on equipment purchased new in the year 2006

EP 1110-1-8

7/31/2009(Vol. 12)

APPENDIX E

2008 195619635 Air Equipment 1888 1801 1730 1720 1733 1683 1695 1668 1563 1630 1521 1354 1295 1186 1165

3092 2967310610 Asphalt & Concrete Paving Equipment 2867 2793 2730 2687 2687 2611 2583 2620 2461 2296 2111 1941 1815 1686 1610

6380 5640590115 Buckets 5314 4872 4767 4713 4640 4527 4471 4541 4313 3879 3280 2963 2738 2520 2175

4540 4152429820 Cranes, Draglines & Clamshells - Crawler & Truck Mtd 3967 3688 3595 3485 3395 3339 3282 3213 3009 2782 2512 2301 2138 2010 1843

3196 3069316325 Drills 2969 2807 2792 2786 2832 2803 2836 2810 2602 2265 1993 1858 1699 1638 1559

4234 4116418130 Generators 3998 3773 3575 3514 3510 3400 3314 3236 3160 2817 2390 2301 2128 2053 1839

4655 4359450935 Graders, Motor 4219 4010 3914 3759 3738 3645 3643 3561 3276 2992 2687 2492 2259 2109 1956

4816 4555467740 Loaders, Track 4404 4163 3918 3770 3767 3791 3792 3655 3349 3061 2750 2482 2247 2053 1916

4758 4532464045 Loaders, Wheel 4409 4235 4099 3991 3973 3944 3873 3788 3441 2938 2606 2375 2156 2002 1907

4427 4182430550 Pile Driving Equipment 4029 3845 3745 3668 3626 3570 3519 3439 3208 2894 2562 2329 2135 1989 1852

4460 4630466855 Rollers 4507 4412 4217 4151 4090 3926 3744 3431 3199 2913 2653 2396 2139 1983 1872

4655 4359450960 Scrapers & Soil Stabilizers 4219 4010 3914 3759 3738 3645 3643 3561 3276 2992 2687 2492 2259 2109 1956

4540 4152429865 Shovels, Backhoes & Hydraulic Excavators 3967 3688 3595 3485 3395 3339 3282 3213 3009 2782 2512 2301 2138 2010 1843

4816 4555467770 Tractors, Crawlers & Attachments 4404 4163 3918 3770 3767 3791 3792 3655 3349 3061 2750 2482 2247 2053 1916

4270 4123418675 Tractor, Wheel 4018 3936 3862 3820 3818 3656 3557 3530 3256 2927 2578 2319 2125 1956 1843

5015 4886494880 Trenchers 4753 4679 4600 4586 4488 4431 4360 4097 3618 3153 2772 2580 2300 1894 1633

3838 3546366985 Trucks, Highway 3495 3363 3299 3282 3139 3055 2934 2824 2638 2324 2108 1934 1775 1646 1524

4797 4617473990 Trucks & Wagons - Off-Highway 4405 4094 3915 3840 3822 3786 3744 3662 3363 2964 2588 2364 2196 2081 1965

4427 4182430595 All Other Equipment 4029 3845 3745 3668 3626 3570 3519 3439 3208 2894 2562 2329 2135 1989 1852

2524 24702506100 All Tires & Tubes 2480 2399 2322 2340 2374 2421 2453 2552 2506 2369 2055 1792 1699 1615 1485

4679 42714438105 Marine Equipment 4091 3920 3886 3863 3749 3633 3497 3391 3239 2922 2587 2352 2156 2008 1870

EK = Economic Key E-2

EP 1110-1-8, Vol. 130 Nov 09

E-3


EP 1110-1-8, Vol. 130 Nov 09

E-4

APPENDIX F TIRE DESCRIPTION AND TIRE COST

EP 1110-1-8, Vol. 130 Nov 09

F-1

EP CODE SIZE DESCRIPTION SIZE PER EACHCOSTTUBE

PLY (1)

TIRE DESCRIPTION AND TIRE COST

EP 1110-1-8(Vol. 8)

7/31/2009

INDUSTRY CODE

APPENDIX F

LT TRUCK/RECREATIONAL VEHICLE, RADIAL

(Life =WORKHORSE EXTRA GRIP RADIAL 5000 hrs )

ABAA3 LT265/75R16 10.40 16.00 TL $203x 10

(Life =WRANGLER RADIAL AT 5000 hrs )

ABAC1 LT235/75R15 9.25 15.00 TL $147x 6ABAC2 31-1050R15 10.50 15.00 TL $141x 6

(Life =SERVICE TRAILER - MARATHON RADIAL 5000 hrs )

ABBF1 ST175/80R13 7.00 13.00 TL $81x 4ABBF3 ST185/80R13 7.20 13.00 TL $93x 6ABBF5 ST205/75R14 8.00 14.00 TL $106x 6ABBF8 ST205/75R15 8.00 15.00 TL $125x 6ABBF6 ST215/75R14 8.50 14.00 TL $112x 6ABBF9 ST225/75R15 8.80 15.00 TL $126x 6ABBF10 ST225/75R15 8.80 15.00 TL $139x 8

LT TRUCK/RECREATIONAL VEHICLE, BIAS

(Life =WORKHORSE RIB 5000 hrs )

ACBA2 700-15LT 8.30 15.00 TL $165x 8ACBA7 875-16.5LT 8.80 16.50 TL $193x 10ACBA4 750-16LT 8.90 16.00 TL $190x 10ACBA9 950-16.5LT 9.60 16.50 TL $212x 10

(Life =TRACTION HI-MILER 5000 hrs )

ACBC1 6.70-15LT 7.50 15.00 TL $162x 6ACBC3 8-14.5LT 8.00 14.50 TL $278x 12ACBC4 9-14.5LT 9.50 14.50 TL $312x 12

(Life =CUSTOM HI-MILER 5000 hrs )

ACBD1 12-16.5LT 12.10 16.50 TL $621x 12

OVER-THE-ROAD TRUCK, COMMERCIAL, RADIAL

(Life =COMMERICAL RADIAL LT TRUCK 5000 hrs )

ADCA2 LT225/75R16 7.50 16.00 TL $242x 10ADCA17 8R19.5 8.00 19.50 TL $422x 10ADCA18 8R195 8.00 19.50 TL $248x 12

F-1(1) TT = includes tube, TL = no tube, NO = no tube

EP 1110-1-8, Vol. 130 Nov 09

F-2


PLY (1)


EP 1110-1-8(Vol. 8)7/31/2009

INDUSTRY CODE

APPENDIX F

ADCA4 LT215/85R16 8.50 16.00 TL $180x 10ADCA3 LT215/85R16 8.50 16.00 TL $197x 8ADCA1 750R16LT 8.70 16.00 TL $174x 8ADCA6 LT225/75R16 8.80 16.00 TL $175x 10ADCA19 225/70R195 8.85 19.50 TL $282x 12ADCA8 LT235/85R16 9.25 16.00 TL $169x 10ADCA21 245/70R195 9.65 19.50 TL $373x 14ADCA11 LT245/75R16 9.80 16.00 TL $185x 10

(Life =COMMERCIAL RADIAL TRUCK TL 5000 hrs )

ADCB2 9R175 9.00 17.50 TL $299x 16ADCB5 9R22.5 9.00 22.50 TL $296x 12ADCB3 10R175 10.00 17.50 TL $301x 16ADCB7 10R22.5 10.00 22.50 TL $400x 14ADCB4 11R17.5 11.00 17.50 TL $389x 16ADCB8 11R22.5 11.00 22.50 TL $509x 16ADCB13 11R24.5 11.00 24.50 TL $550x 16ADCB10 12R22.5 12.00 22.50 TL $597x 16ADCB14 12R24.5 12.00 24.50 TL $614x 16

(Life =LOW PROFILE RADIAL TRUCK TL 5000 hrs )

ADCC1 215/75R175 8.40 17.50 TL $269x 16ADCC5 245/75R22.5 9.60 22.50 TL $306x 14ADCC3 255/70R22.5 10.00 22.50 TL $353x 16ADCC2 265/70R19.5 10.40 19.50 TL $327x 14ADCC6 265/75R22.5 10.40 22.50 TL $372x 14ADCC4 275/70R22.5 10.80 22.50 TL $412x 16ADCC12 285/75R24.5 11.20 24.50 TL $543x 14ADCC8 295/75R22.5 11.60 22.50 TL $551x 16ADCC10 315/80R22.5 12.40 22.50 TL $596x 18

(Life =SUPER SINGLE COMMERCIAL RADIAL TRUCK 5000 hrs )

ADCD1 385/65R22.5 15.10 22.50 TL $684x 18ADCD2 425/65R22.5 16.70 22.50 TL $769x 20ADCD3 445/65R22.5 17.50 22.50 TL $869x 20

(Life =COMMERCIAL RADIAL TRUCK TT 5000 hrs )

ADCE1 825R15 8.25 15.00 TT $315x 14ADCE5 9.00R20 8.25 20.00 TT $372x 12


EP 1110-1-8, Vol. 130 Nov 09

F-3


PLY (1)


EP 1110-1-8(Vol. 8)

7/31/2009

INDUSTRY CODE

APPENDIX F

ADCE6 9.00R20 9.00 20.00 TT $396x 12ADCE3 1000R15 10.00 15.00 TT $412x 14ADCE7 1000R20 10.00 20.00 TT $441x 14ADCE13 10R22.5 10.00 22.50 TL $440x 12ADCE12 365/80R20 10.40 20.00 TT $660x 18ADCE9 1100R20 11.00 20.00 TT $514x 16ADCE10 1100R20 11.00 20.00 TT $587x 16ADCE14 1100R22 11.00 22.00 TT $609x 16ADCE15 1100R24 11.00 24.00 TT $610x 16ADCE11 1200R20 12.00 20.00 TT $627x 18ADCE17 1200R24 12.00 24.00 TT $683x 18

FARM, FRONT

(Life =DYNA RIB F-2-M 5000 hrs )

AFED2 1000-16 10.00 16.00 TL $316x 8F-2MAFED1 11L-15 11.00 15.00 TL $296x 6F-2MAFED4 1100-16 11.00 16.00 TL $418x 8F-2MAFED8 1100-24 11.00 24.00 TL $827x 12F-2MAFED6 14L-161 14.00 16.10 TL $690x 10F-2MAFED7 165L-161 16.50 16.10 TL $800x 8F-2M

(Life =SINGLE RIB FRONT TRACTOR F-1 5000 hrs )

AFEE1 600-16 6.00 16.00 TT $180x 4F-1

(Life =FARM HIGHWAY SERVICE 5000 hrs )

AFEF2 95L-15FI 9.50 15.00 TL $240x DI-1AFEF5 11L-15FI 11.00 15.00 TL $314x FI-1AFEF7 125L-15FI 12.50 15.00 TL $434x FI-1

(Life =FARM UTILITY 5000 hrs )

AFEG7 750-14 7.50 14.00 TL $167x 4I-1AFEG14 760-15 7.60 15.00 TL $187x 8I-1AFEG8 85L-14 8.50 14.00 TL $173x 6I-1AFEG1 95L-14 9.50 14.00 TT $163x 8I-1AFEG17 95L-15 9.50 15.00 TL $247x 12I-1AFEG18 1000-15 10.00 15.00 TL $255x 8I-1AFEG11 11L-14 11.00 14.00 TL $194x 8I-1AFEG22 11L-15 11.00 15.00 TL $271x 10I-1


EP 1110-1-8, Vol. 130 Nov 09

F-4


PLY (1)


EP 1110-1-8(Vol. 8)7/31/2009

INDUSTRY CODE

APPENDIX F

AFEG20 11L-15 11.00 15.00 TL $190x 8I-1AFEG34 11L-16 11.00 16.00 TL $248x 10I-1AFEG25 125L-15 12.50 15.00 TL $305x 12I-1AFEG30 125L-16 12.50 16.00 TL $349x 12I-1AFEG29 125L-16 12.50 16.00 TL $309x 8I-1AFEG28 14L-161 14.00 16.10 TL $514x 12I-1AFEG31 165L-161 16.50 16.10 TL $619x 10I-1AFEG32 19L-161 19.00 16.10 TL $671x 10I-1AFEG27 215L-161 21.50 16.10 TL $1,063x 14I-1

(Life =FOUR RIB FRONT TRACTOR F-2-M 5000 hrs )

AFEH1 750-16 7.50 16.00 TT $196x 6F-2MAFEH3 1000-16 10.00 16.00 TT $280x 8F-2MAFEH4 1100-16 11.00 16.00 TT $326x 8F-2M

(Life =IMPLEMENT RIB 5000 hrs )

AFEK11 400-18 4.00 18.00 TT $137x 4I-1AFEK4 500-15 5.00 15.00 TL $138x 4I-1AFEK16 590-15 5.90 15.00 TL $142x 4I-1AFEK6 600-16 6.00 16.00 TT $149x 6I-1AFEK7 650-16 6.50 16.00 TT $143x 6I-1AFEK5 670-15 6.70 15.00 TL $153x 6I-1AFEK9 750-16 7.50 16.00 TT $200x 10I-1AFEK10 900-16 9.00 16.00 TL $288x 10I-1AFEK13 900-24 9.00 24.00 TL $457x 8I-1AFEK14 1125-28 11.25 28.00 TT $1,207x 12I-1

(Life =LABORER F-3 5000 hrs )

AFEL6 145/75-161 5.70 16.10 TL $858x 10F-3AFEL2 11L-15 11.00 15.00 TL $273x 10F-3AFEL4 11L-16 11.00 16.00 TL $257x 10F-3AFEL5 11L-16 11.00 16.00 TL $296x 12F-3

(Life =MULTI-RIB F-3 5000 hrs )

AFEM1 900-10 9.00 10.00 TT $264x 10F-3TFEM2 1100-16 11.00 16.00 TL $407x 12F-3

(Life =SMOOTH 5000 hrs )

AFEN1 169-30 16.90 30.00 TL $1,742x 6I-1


EP 1110-1-8, Vol. 130 Nov 09

F-5


PLY (1)


EP 1110-1-8

(Vol. 8)

7/31/2009

INDUSTRY CODE

APPENDIX F

(Life =SMOOTH IMP 5000 hrs )

AFEO1 400-8 4.00 8.00 TL $91x 4AFEO3 600-16 6.00 16.00 TL $283x 10AFEO2 11L-15 11.00 15.00 TL $271x 10

(Life =SOFTRAC II 5000 hrs )

AFEP1 165L-161 16.50 16.10 TL $742x 6I-2AFEP3 215L-161 21.50 16.10 TL $1,464x 10I-2

(Life =SUPER RIB F-2 5000 hrs )

TFER1 400-12 4.00 12.00 TT $86x 4F-2

(Life =COMPACT UTILITY R-1 5000 hrs )

TFES2 5-12 5.00 12.00 TL $91x 4 AFES1 7-16 7.00 16.00 TL $179x 6

(Life =SURE GRIP IMPLEMENT 5000 hrs )

AFET1 105/80-18 10.50 18.00 TL $725x 10I-3AFET2 125/80-18 12.50 18.00 TL $781x 10I-3

(Life =SURE GRIP LUG 5000 hrs )

AFEU2 105/80-18 10.50 18.00 TL $732x 10I-3AFEU1 124-16 12.40 16.00 TL $631x 4I-3AFEU3 125/80-18 12.50 18.00 TL $696x 10I-3

(Life =SURE GRIP TRACTION 5000 hrs )

AFEV1 670-15 6.70 15.00 TT $160x 4I-3AFEV5 750-16 7.50 16.00 TL $249x 4I-3AFEV2 750-18 7.50 18.00 TT $245x 4I-3AFEV3 750-20 7.50 20.00 TT $291x 4I-3AFEV4 760-15 7.60 15.00 TL $213x 6I-3

(Life =TRACTION IMPLEMENT 5000 hrs )

AFEW1 500-15 5.00 15.00 TL $155x 4I-3AFEW2 590-15 5.90 15.00 TL $166x 4I-3

(Life =TRIPLE RIB HD 5000 hrs )

AFEX8 550-16 5.50 16.00 TT $169x 6F-2AFEX10 600-16 6.00 16.00 TT $194x 6F-2AFEX11 650-16 6.50 16.00 TT $170x 6F-2


EP 1110-1-8, Vol. 130 Nov 09

F-6


PLY (1)


EP 1110-1-8(Vol. 8)7/31/2009

INDUSTRY CODE

APPENDIX F

AFEX4 75L-15 7.50 15.00 TT $176x 6F-2AFEX18 750-16 7.50 16.00 TL $220x 6F-2AFEX13 750-16 7.50 16.00 TT $216x 8F-2AFEX14 750-18 7.50 18.00 TT $236x 6F-2AFEX5 95L-15 9.50 15.00 TT $254x 8F-2AFEX16 1000-16 10.00 16.00 TL $299x 8F-2AFEX6 11L-15 11.00 15.00 TT $290x 8F-2AFEX17 1100-16 11.00 16.00 TL $384x 8F-2

(Life =TRIPLE RIB R/S F-2 5000 hrs )

AFEY2 400-15 4.00 15.00 TT $118x 4F-2AFEY1 500-15 5.00 15.00 TT $121x 4F-2

(Life =DURATORQUE R-1 5000 hrs )

AFFU3 8-16 8.00 16.00 TL $250x 6R-1

FARM, REAR

(Life =ALL TRACTION R-3 5000 hrs )

AGFA1 750-16 7.50 16.00 TT $231x 4R-3

(Life =ALL WEATHER R-3 5000 hrs )

AGFB2 95-24 9.50 24.00 TT $609x 4R-3AGFB7 136-161 13.60 16.10 TL $1,030x 8R-3AGFB5 136-28 13.60 28.00 TT $780x 6R-3AGFB3 149-24 14.90 24.00 TL $783x 6R-3AGFB4 169-24 16.90 24.00 TL $904x 6R-3AGFB8 184-161 18.40 16.10 TL $1,102x 8R-3AGFB10 184-26 18.40 26.00 TL $1,481x 12R-3AGFB11 231-26 23.10 26.00 TL $2,209x 10R-3AGFB12 231-26 23.10 26.00 TL $2,337x 12R-3AGFB14 245-32 24.50 32.00 TL $3,285x 12R-3AGFB13 28L-26 28.00 26.00 TL $3,118x 16R-3AGFB15 305L-32 30.50 32.00 TL $3,581x 12R-3AGFB16 305L-32 VA 30.50 32.00 TL $5,771x 24R-3

(Life =DT 800 RADIAL R-1W 5000 hrs )

AGFE1 320/90R42 12.60 42.00 TL $1,748x 139A8R-1WAGFE3 320/90R50 12.60 50.00 TL $2,207x 148A8R-1W


EP 1110-1-8, Vol. 130 Nov 09

F-7


PLY (1)


EP 1110-1-8(Vol. 8)

7/31/2009

INDUSTRY CODE

APPENDIX F

AGFE2 380/90R46 14.90 46.00 TL $2,482x 149A8R-1W


AGFF1 380/70R24 14.90 24.00 TL $1,863x UKR-1WAGFF2 420/70R28 16.50 28.00 TL $1,171x UKR-1WAGFF3 480/70R30 18.90 30.00 TL $2,115x UKR-1W


AGFG2 600/65R28 23.60 28.00 TL $2,923x UKR-1WAGFG1 620/75R26 24.40 26.00 TL $4,648x UKR-1WAGFG5 620/70R42 24.40 42.00 TL $3,727x UKR-1WAGFG3 650/75R34 25.60 34.00 TL $4,625x UKR-1WAGFG4 710/70R38 27.90 38.00 TL $3,984x UKR-1W

(Life =DYNA TORQUE RADIAL R-1 5000 hrs )

TGFH5 320/85R34 12.60 34.00 TL $1,556x 132DR-1AGFH7 149R30 14.90 30.00 TL $1,321x X3R-1AGFH9 149R34 14.90 34.00 TL $1,431x X3R-1AGFH15 149R46 14.90 46.00 TL $1,490x X3R-1TGFH6 385/85R34 15.20 34.00 TL $1,736x 141GR-1AGFH16 420/80R46 16.50 46.00 TL $2,971x UKR-1AGFH8 169R30 16.90 30.00 TL $1,762x X3R-1TGFH2 184R26 18.40 26.00 TL $1,842x X2R-1AGFH10 184R38 18.40 38.00 TL $1,320x X1R-1AGFH13 184R42 18.40 42.00 TL $1,644x X2R-1AGFH17 184R46 18.40 46.00 TL $1,981x X3R-1AGFH12 208R38 20.80 38.00 TL $1,819x X1R-1AGFH14 208R42 20.80 42.00 TL $1,925x X2R-1

(Life =DYNA TORQUE II R-1 5000 hrs )

AGFJ29 112-16 11.20 16.00 TL $375x 4R-1AGFJ6 136-24 13.60 24.00 TT $843x 8R-1AGFJ11 136-28 13.60 28.00 TL $937x 10R-1AGFJ41 136-28 13.60 28.00 TL $937x 10R-1AGFJ7 149-24 14.90 24.00 TL $721x 6R-1AGFJ31 149-24 14.90 24.00 TL $737x 8R-1AGFJ42 149-28 14.90 28.00 TL $1,160x 10R-1AGFJ8 169-24 16.90 24.00 TT $806x 6R-1AGFJ39 169-26 16.90 26.00 TL $1,479x 10R-1


EP 1110-1-8, Vol. 130 Nov 09

F-8


PLY (1)


EP 1110-1-8

(Vol. 8)

7/31/2009

INDUSTRY CODE

APPENDIX F

AGFJ43 169-28 16.90 28.00 TL $1,495x 10R-1AGFJ37 169-34 16.90 34.00 TT $1,016x 6R-1AGFJ23 169-38 16.90 38.00 TL $1,951x 14R-1AGFJ40 184-26 18.40 26.00 TL $1,419x 12R-1AGFJ18 184-34 18.40 34.00 TT $1,166x 8R-1AGFJ24 184-38 18.40 38.00 TT $1,249x 8R-1AGFJ19 208-34 20.80 34.00 TT $1,816x 8R-1AGFJ25 208-38 20.80 38.00 TT $1,643x 8R-1AGFJ27 208-42 20.80 42.00 TL $2,422x 10R-1AGFJ45 231-26 23.10 26.00 TL $2,337x 12R-1AGFJ20 231-34 23.10 34.00 TT $2,203x 8R-1AGFJ35 245-32 24.50 32.00 TL $2,536x 12R-1AGFJ34 28L-26 28.00 26.00 TL $3,055x 12R-1AGFJ36 305L-32 30.50 32.00 TL $3,665x 14R-1

(Life =INDUSTRIAL SURE GRIP R-4 5000 hrs )

AGFK1 169-30 16.90 30.00 TT $2,058x 10R-4AGFK3 184-28 18.40 28.00 TL $1,295x 12R-4

(Life =IT510 RADIAL R4 5000 hrs )

AGFL3 195LR24 19.50 24.00 TL $1,854x UKR-4

(Life =IT525 RADIAL R4 5000 hrs )

AGFM1 149-24 14.90 24.00 TL $871x 8R-4AGFM4 169-24 16.90 24.00 TL $1,005x 10R-4AGFM12 169-28 16.90 28.00 TL $1,122x 10R-4AGFM6 175L-24 17.50 24.00 TL $882x 10R-4AGFM5 184-24 18.40 24.00 TL $1,390x 12R-4AGFM7 195L-24 19.50 24.00 TL $1,252x 10R-4AGFM8 195L-24 19.50 24.00 TL $1,278x 12R-4AGFM9 21L-24 21.00 24.00 TL $1,542x 12R-4AGFM11 21L-24 21.00 24.00 TL $1,774x 16R-4AGFM14 21L-28 21.00 28.00 TL $1,821x 14R-4

(Life =POWER TORQUE R-1 5000 hrs )

AGFN1 6-12 6.00 12.00 TL $135x 4R-1

(Life =SPECIAL SURE GRIP R-2-0 5000 hrs )

AGFO2 149-24 14.90 24.00 TL $1,463x 6R-2


EP 1110-1-8, Vol. 130 Nov 09

F-9


PLY (1)


EP 1110-1-8(Vol. 8)

7/31/2009

INDUSTRY CODE

APPENDIX F

AGFO11 184-26 18.40 26.00 TL $1,470x 10R-2AGFO8 184-38 18.40 38.00 TL $2,057x 8R-2AGFO12 VA500/95D32 19.70 32.00 TL $4,124x 20R-2AGFO10 208-38 20.80 38.00 TL $1,840x 8R-2AGFO3 231-26 23.10 26.00 TL $2,356x 10R-2AGFO4 28L-26 28.00 26.00 TL $3,279x 12R-2AGFO6 305L-32 30.50 32.00 TL $4,670x 14R-2

(Life =SPECIAL SURE GRIP RADIAL R-2-0 5000 hrs )

AGFP8 320/90R46 12.60 46.00 TL $2,101x R-2AGFP9 340/85R46 13.40 46.00 TL $2,271x UKR-2AGFP1 169R28 16.90 28.00 TL $2,168x X2R-2AGFP2 169R30 16.90 30.00 TL $2,373x X3R-2AGFP3 184R38 18.40 38.00 TL $2,376x X1R-2AGFP5 184R42 18.40 42.00 TL $2,814x X2R-2AGFP7 184R46 18.40 46.00 TL $3,126x X3R-2AGFP4 208R38 20.80 38.00 TL $2,930x X2R-2AGFP6 208R42 20.80 42.00 TL $2,720x X2R-2

(Life =SUPER TRACTION RADIAL R-1W 5000 hrs )

AGFQ3 260/80R20 10.20 20.00 TL $551x 8R-1WAGFQ2 112R20 11.20 20.00 TL $899x UKR-1WAGFQ6 136R28 13.60 28.00 TL $1,733x UKR-1WAGFQ15 136R38 13.60 38.00 TL $2,074x UKR-1WAGFQ20 149R24 14.90 24.00 TL $1,861x X2R-1WAGFQ7 149R28 14.90 28.00 TL $1,909x UKR-1WAGFQ9 149R30 14.90 30.00 TL $1,545x UKR-1WAGFQ4 169R24 16.90 24.00 TL $2,553x UKR-1WAGFQ5 169R26 16.90 26.00 TL $2,604x UKR-1WAGFQ8 169R28 16.90 28.00 TL $1,873x UKR-1WAGFQ10 169R30 16.90 30.00 TL $1,991x UKR-1WAGFQ21 169R34 16.90 34.00 TL $2,557x X2R-1WAGFQ22 169R38 16.90 38.00 TT $2,683x X2R-1WAGFQ11 184R26 18.40 26.00 TL $1,951x UKR-1WAGFQ12 184R30 18.40 30.00 TL $2,853x UKR-1WAGFQ14 184R34 18.40 34.00 TL $3,053x UKR-1WAGFQ16 184R38 18.40 38.00 TL $2,030x UKR-1WAGFQ18 184R42 18.40 42.00 TL $2,678x UKR-1W


EP 1110-1-8, Vol. 130 Nov 09

F-10


PLY (1)


EP 1110-1-8(Vol. 8)7/31/2009

INDUSTRY CODE

APPENDIX F

AGFQ17 208R38 20.80 38.00 TL $2,833x UKR-1WAGFQ19 208R42 20.80 42.00 TL $2,368x UKR-1WAGFQ13 800/65R32 31.50 32.00 TL $4,532x UKR-1W

(Life =DURATORQUE R-1 5000 hrs )

AGFU1 149-28 14.90 28.00 TT $643x 6R-1AGFU2 169-30 16.90 30.00 TT $902x 6R-1AGFU3 184-30 18.40 30.00 TT $1,076x 8R-1AGFU5 184-38 18.40 38.00 TT $1,192x 8R-1

FARM, TERRA - 20" UP

(Life =SFT105 5000 hrs )

AHGA2 54-3100-26 31.00 26.00 TL $2,442x 10HF-1

(Life =SOF TRAC 5000 hrs )

AHGB3 38-1400-20 14.00 20.00 TL $626x 4HF-1AHGB2 41-1400-20 14.00 20.00 TL $675x 4HF-1AHGB1 44-1800-20 18.00 20.00 TL $941x 4HF-1

(Life =SUPER TERRA GRIP 5000 hrs )

AHGC1 38-1400-20 14.00 20.00 TL $768x 8HF-2AHGC2 42-2500-20 25.00 20.00 TL $2,259x 8HF-2AHGC7 54-3100-26 31.00 26.00 TL $6,785x 10HF-2AHGC12 67-3400-25 34.00 25.00 TL $5,629x 10HF-2AHGC11 66-4300-25 43.00 25.00 TL $9,219x 20HF-2

(Life =SUPER TERRA GRIP XT 5000 hrs )

AHGD1 42-2500-20 25.00 20.00 TL $3,430x 12HF-3AHGD5 48-3100-20 31.00 20.00 TL $4,352x 12HF-3AHGD6 66-4300-25 43.00 25.00 TL $6,269x 10HF-3AHGD7 73-4400-32 44.00 32.00 TL $9,815x 16HF-3

(Life =TUNDRA GRIP 5000 hrs )

AHGF2 66-4400-25 44.00 25.00 TL $7,285x 16HF-1AHGF1 66-4400-25 44.00 25.00 TL $8,106x 20HF-1

FARM, SPECIALTY


EP 1110-1-8, Vol. 130 Nov 09

F-11


PLY (1)


EP 1110-1-8(Vol. 8)

7/31/2009

INDUSTRY CODE

APPENDIX F

(Life =SOFTRAC 5000 hrs )

IJHB2 18-650-8 6.50 8.00 TL $102x 4TJHB3 18-850-10 8.50 10.00 TL $109x 4AJHB1 25-850-14 8.50 14.00 TL $214x 6HF-1AJHB5 27-850-15 8.50 15.00 TL $217x 4HF-1AJHB4 25-1050-15 10.50 15.00 TL $244x 4HF-1AJHB6 27-1050-15 10.50 15.00 TL $271x 4HF-1AJHB7 29-1250-15 12.50 15.00 TL $309x 4HF-1AJHB10 31-1250-15 12.50 15.00 TL $311x 4HF-1AJHB11 33-1250-15 12.50 15.00 TL $532x 4HF-1AJHB8 31-1350-15 13.50 15.00 TL $359x 4HF-1AJHB9 31-1550-15 15.50 15.00 TL $395x 4HF-1

(Life =SUPER TERRA GRIP 5000 hrs )

AJHC3 29-1250-15 12.50 15.00 TL $287x 6HF-2AJHC6 31-1550-15 15.50 15.00 TL $505x 8HF-2AJHC7 38-2000-16.1 20.00 16.00 TL $1,035x 8HF-2

(Life =SURE GRIP LUG 5000 hrs )

AJHD9 27-850-15 8.50 15.00 TL $244x 6HF-2AJHD1 10-165 10.00 16.50 TL $298x 6AJHD10 27-1050-15 10.50 15.00 TL $358x 6HF-2AJHD4 12-165 12.00 16.50 TL $443x 10 AJHD3 12-165 12.00 16.50 TL $394x 8AJHD5 14-175 14.00 17.50 TL $366x 10I-3AJHD7 15-195 15.00 19.50 TL $553x 12I-3AJHD6 15-195 15.00 19.50 TL $718x 12

(Life =IT 323 5000 hrs )

AJHE1 10-165 10.00 16.50 TL $374x 8AJHE3 12-165 12.00 16.50 TL $519x 10AJHE4 31-1550-15 15.50 15.00 TL $930x 8

(Life =POWER RIB 5000 hrs )

TJHJ1 18-850-8 8.50 8.00 TL $88x 4IJHJ2 20-1000-10 10.00 10.00 TL $186x 4

(Life =RALLY 5000 hrs )

TJHK1 480-8 4.80 8.00 TL $43x 4


EP 1110-1-8, Vol. 130 Nov 09

F-12


PLY (1)


EP 1110-1-8(Vol. 8)7/31/2009

INDUSTRY CODE

APPENDIX F

IJHK2 18-950-8 9.50 8.00 TL $201x 4

(Life =TERRA RIB 5000 hrs )

AJHM2 25-750-15 7.50 15.00 TL $221x 6HF-1AJHM4 27-950-15 9.50 15.00 TL $358x 10HF-1AJHM6 31-1350-15 13.50 15.00 TL $465x 8HF-1

(Life =ATV 5000 hrs )

TJHN1 AT21-7-10 7.00 10.00 TL $69x X3IJHN3 AT23-8-11 8.00 11.00 TL $146x 6TJHN5 AT24-9-11 9.00 11.00 TL $145x 6

(Life =TRACKER ATT 5000 hrs )

IJHT1 AT24-8-11 8.00 11.00 TL $161x X2IJHT2 AT24-10-11 10.00 11.00 TL $157x X2

INDUSTRIAL, MINE SERVICE

(Life =HARD ROCK LUG MINE & INDUSTRIAL 5000 hrs )

TKJC1 10.00-20 10.00 20.00 TT $807x 18

(Life =XTRA TRACTION LUG 5000 hrs )

AKJD2 8.25-15 8.25 15.00 TT $757x 16AKJD3 36-11x15(10.00L15) 10.00 15.00 TT $931x 16AKJD7 24x12x12 12.00 12.00 TL $752x 24AKJD6 35-15x15(14.50L-15) 14.50 15.00 TL $1,535x 32

(Life =XTRA TRACTION GRIP 5000 hrs )

AKJE1 32x15-15 12.00 15.00 TL $1,202x 20

OFF-THE-ROAD, MED & HEAVY COMMERCIAL, RADIAL

(Life =G-2 GRADER SERVICE - RL2F, SG2B 3200 hrs )

AMLA1 14.00R24 14.00 24.00 TL $828x X1G2

(Life =E-2 HAULAGE SERVICE - RL2F/GP2B RL2+ 2800 hrs )

AMLB1 17.5R25 17.50 25.00 TL $1,253x X1E/L/G3AMLB8 18.00R25 18.00 25.00 TL $4,403x X2L5AMLB2 20.5R25 20.50 25.00 TL $1,771x X1E/L/G3AMLB9 20.5R25 20.50 25.00 TL $1,771x X2E/L/G3AMLB5 20.5R25 20.50 25.00 TL $3,143x X2E/K 3T


EP 1110-1-8, Vol. 130 Nov 09

F-13


PLY (1)


EP 1110-1-8(Vol. 8)

7/31/2009

INDUSTRY CODE

APPENDIX F

AMLB15 21.00R35 21.00 35.00 TL $7,384x X2E4AMLB3 23.5R25 23.50 25.00 TL $2,488x X1E/L/G3AMLB10 23.5R25 23.50 25.00 TL $2,659x X2E/L/G3AMLB21 26.5R25 26.50 25.00 TL $5,530x X2E/L/G 3+TAMLB22 29.5R25 29.50 25.00 TL $6,607x X2E/L 3AMLB17 33.25R35 33.25 35.00 TL $10,195x X2E3AMLB23 40.5/75R39 40.50 39.00 TL $15,305x X2E3+

(Life =E-3 HAULAGE SERVICE - ROCK DESIGN RL3, RL3J, R 2800 hrs )

AMLC3 18.00R33 18.00 33.00 TL $4,226x X2E3+AMLC5 24.00R35 24.00 35.00 TL $8,329x X2E3+AMLC6 29.5R29 29.50 29.00 TL $7,546x X2E3AMLC7 33.25R35 33.25 25.00 TL $10,195x X2E3AMLC8 37.25R35 37.35 35.00 TL $12,390x X2E3AMLC9 37.5R39 37.50 39.00 TL $13,690x X2E3

(Life =E-4 RL4J/RL4 & RL4H/RL4 E4 5000 hrs )

AMLD1 12.00R24 12.00 24.00 TT $1,516x X3E4AMLD2 14.00R24 14.00 24.00 TL $1,661x X3E4AMLD3 14.00R25 14.00 25.00 TL $1,750x X3E4AMLD4 18.00R25 18.00 25.00 TL $3,722x X2E4AMLD5 18.00R33 18.00 33.00 TL $5,093x X2E4AMLD14 21.00R35 21.00 35.00 TL $7,384x X2E4AMLD15 24.00R35 24.00 25.00 TL $9,698x X2E4AMLD7 27.00R49 27.00 49.00 TL $13,602x X2E4AMLD8 30.00R51 30.00 51.00 TL $17,439x X2E4AMLD9 33.00R51 33.00 51.00 TL $21,535x X2E4AMLD10 36.00R51 36.00 51.00 TL $24,665x X2E4AMLD11 37.00R57 37.00 57.00 TL $44,480x X2E4AMLD12 40.00R57 40.00 57.00 TL $45,057x X2E4

(Life =MOBILE CRANE 5000 hrs )

AMLF1 445/80R25 (17.5R25) 17.50 25.00 TL $2,112x UKE/L/G3AMLF3 525/80R25 (20.5R25) 20.60 25.00 TL $1,771x UKE/L/G3

(Life =L-5 DOZER & LOADER SERVICE RL5K 8000 hrs )

AMLG1 20.5R25 20.50 25.00 TL $3,907x X1L5AMLG2 23.5R25 23.50 25.00 TL $4,819x X1L5


EP 1110-1-8, Vol. 130 Nov 09

F-14


PLY (1)


EP 1110-1-8(Vol. 8)7/31/2009

INDUSTRY CODE

APPENDIX F

(Life =SPECIAL SERVICE - AT2A 5000 hrs )

AMLH1 14.00R20 14.00 20.00 TL $1,173x 18E/L/G 3AMLH3 16.00R20 16.00 20.00 TL $1,764x 22E/L/G 3AMLH4 16.00R21 16.00 21.00 TL $196x 22E/L/G 3AMLH2 17.5R25 17.50 25.00 TL $1,253x X1E/L/G3AMLH6 22/65R25 22.00 25.00 TL $2,466x X1E/L/G3

OFF-THE-ROAD, MED & HEAVY COMMERCIAL, BIAS

(Life =INDUSTRIAL SURE GRIP MPT 5000 hrs )

ANMA1 10.5-20 10.50 20.00 TL $363x 10ANMA2 12.5-20 12.50 20.00 TL $464x 10

(Life =E-1 HRR 1A 2500 hrs )

ANMB1 14.00-25 14.00 25.00 TL $1,206x 20E3ANMB2 16.00-25 16.00 25.00 TL $2,154x 32E1

(Life =E-2 TRACTION EARTHMOVER SURE GRIP 2800 hrs )

ANMC3 18.00-25 18.00 25.00 TL $1,604x 16E7

(Life =E-3 ROCK SERVICE HARD ROCK LUG/HRL WC 2800 hrs )

ANME1 12.00-20 12.00 20.00 TT $883x 20E3ANME2 12.00-24 12.00 24.00 TT $844x 16E3ANME3 14.00-24 14.00 24.00 TT $1,583x 28E3ANME4 14.00-25 14.00 25.00 TL $1,206x 20E3ANME6 16.00-25 16.00 25.00 TL $1,752x 24E3

(Life =E-3 ROCK SERVICE SUPER HARD ROCK LUG 2800 hrs )

ANMF1 26.5-25 26.50 25.00 TL $5,110x 24L5ANMF4 29.5-25 29.50 25.00 TL $7,064x 28L5ANMF5 29.5-29 29.50 29.00 TL $6,156x 28L4ANMF6 29.5-29 29.50 29.00 TL $5,778x 34E3

(Life =E-3 ROCK SERVICE SHRL8 2800 hrs )

ANMG4 29.5-35 29.50 35.00 TL $6,077x 34E3ANMG1 33.25-29 33.25 29.00 TL $6,344x 26E3TNMG6 33.25-35 33.25 35.00 TL $9,551x 38E3ANMG7 37.25-35 37.25 35.00 TL $8,020x 36E3ANMG9 37.5-39 37.50 39.00 TL $8,961x 44E3


EP 1110-1-8, Vol. 130 Nov 09

F-15


PLY (1)


EP 1110-1-8(Vol. 8)

7/31/2009

INDUSTRY CODE

APPENDIX F

(Life =E-3 ROCK SERVICE ELV3A, ELV4B, ELV4/5A 2800 hrs )

ANMH4 18.00-25 18.00 25.00 TL $4,768x 40IND 5SANMH9 21.00-25 21.00 25.00 TL $4,544x 32IND 3

(Life =E-3 ROCK SERVICE HRL 3F 2800 hrs )

ANMJ2 33.25-35 33.25 35.00 TL $6,267x 32E3ANMJ5 37.25-35 37.25 35.00 TL $8,016x 36E3ANMJ6 37.5-39 37.50 39.00 TL $8,961x 44E3

(Life =E-3 ROCK SERVICE WRL 3A 2800 hrs )

ANML1 14.00-20 14.00 20.00 TT $1,253x 24E3ANML2 14.00-24 14.00 24.00 TT $1,330x 24E3

(Life =E-4 ROCK SERVICE HRL 4B 5000 hrs )

ANMN1 16.00-25 16.00 25.00 TL $2,182x 28E4ANMN3 18.00-33 18.00 33.00 TL $3,863x 32E4ANMN4 21.00-35 21.00 35.00 TL $5,616x 36E4ANMN5 24.00-35 24.00 35.00 TL $7,269x 36E4ANMN9 36.00-51 36.00 51.00 TL $23,181x 58E4

(Life =E-7 FLOTATION TYPE SAND RIB SRB 7A 3000 hrs )

TNMQ1 14.00-20 14.00 20.00 TL $581x 10E7TNMQ2 16.00-24 16.00 24.00 TL $1,510x 12E7TNMQ3 18.00-25 18.00 25.00 TL $2,057x 16E7

(Life =E-7 FLOTATION TYPE PAVER TIRE 3000 hrs )

ANMR1 1600-24 16.00 24.00 TL $1,235x 12E7

(Life =G-2 SGG2A 3200 hrs )

ANMT1 13.00-24 13.00 24.00 TL $408x 10G2ANMT10 13.00-24 13.00 24.00 TL $341x 12G2ANMT6 14.00-24 14.00 24.00 TL $381x 12G2ANMT8 16.00-24 16.00 24.00 TL $1,311x 12G2

(Life =G-2 SGLDL 2A L2 3200 hrs )

ANMV2 15.5-25 15.50 25.00 TL $516x 12L2/G2ANMV3 17.5-25 17.50 25.00 TL $540x 12L2/G2ANMV4 17.5-25 17.50 25.00 TL $698x 16L2/G2ANMV5 17.5-25 17.50 25.00 TL $900x 20L2/G2


EP 1110-1-8, Vol. 130 Nov 09

F-16


PLY (1)


EP 1110-1-8

(Vol. 8)

7/31/2009

INDUSTRY CODE

APPENDIX F

(Life =G-2 SGLEL 2A ES/L2/G2 3200 hrs )

ANMW1 20.5-25 20.50 25.00 TL $997x 12E/L/G2ANMW2 20.5-25 20.50 25.00 TL $1,077x 16E/L/G2ANMW4 23.5-25 23.50 25.00 TL $1,549x 12E/L/G2ANMW5 23.5-25 23.50 25.00 TL $1,764x 16E/L/G2

(Life =G-3 RKG 3A 3200 hrs )

TNMX1 14.00-24 14.00 24.00 TL $826x 14G2

(Life =L-2 DOZER/LOADER SERVICE TRACTION SG LUG DL 3200 hrs )

ANNA2 26.5-25 26.50 25.00 TL $3,273x 20L3

(Life =L-3 DOZER/LOADER SERVICE ROCK SERVICE E3/L3 3200 hrs )

ANNB1 20.5-25 20.50 25.00 TL $1,405x 12E/L 3ANNB2 20.5-25 20.50 25.00 TL $1,445x 16E/L 3ANNB5 23.5-25 23.50 25.00 TL $2,053x 16E/L 3ANNB6 23.5-25 23.50 25.00 TL $2,345x 20E/L 3

(Life =L-3 DOZER/LOADER SERVICE ROCK SHRL DL 3200 hrs )

ANNC1 26.5-25 26.50 25.00 TL $3,273x 20L3ANNC3 29.5-25 29.50 25.00 TL $6,156x 28L4

(Life =L-3 DOZER/LOADER SERVICE ROCK HRL DL 3A & 3F 3200 hrs )

ANND2 17.5-25 17.50 25.00 TL $652x 12L/G3ANND4 17.5-25 17.50 25.00 TL $1,066x 20L/G3

(Life =L-4 DOZER/LOADER SERVICE ROCK DEEP TREAD S 5000 hrs )

ANNE2 26.5-25 26.50 25.00 TL $3,273x 20L3ANNE4 29.5-25 29.50 25.00 TL $6,156x 28L4ANNE5 29.5-29 29.50 29.00 TL $5,778x 34E3

(Life =L-4 DOZER/LOADER SERVICE ROCK DEEP TREAD N 5000 hrs )

TNNG1 35/65-33 35.00 33.00 TL $13,905x 42L5

(Life =L-5 DOZER/LOADER SERVICE ROCK SUPER XTRA T 8000 hrs )

ANNL2 35/65-33 35.00 33.00 TL $10,727x 30L5ANNL4 41.25/70-39 41.25 39.00 TL $16,327x 42L5ANNL7 45/65-45 45.00 45.00 TL $27,141x 58L5


EP 1110-1-8, Vol. 130 Nov 09

F-17


PLY (1)


EP 1110-1-8(Vol. 8)

7/31/2009

INDUSTRY CODE

APPENDIX F

(Life =L-5 DOZER/LOADER SERVICE SMOOTH SMO SL5B 8000 hrs )

ANNN3 18.00-25 18.00 25.00 TL $2,939x 32IND 3

(Life =L-5 DOZER/LOADER SERVICE SMOOTH SUPER XTRA 8000 hrs )

ANNO1 21.00-25 21.00 25.00 TL $6,527x 32L5SANNO3 26.5-25 26.50 25.00 TL $6,332x 32L5SANNO4 29.5-25 29.50 25.00 TL $8,199x 28L5S

(Life =L-5 DOZER/LOADER SERVICE SMOOTH NSM DL5B 8000 hrs )

ANNP1 35/65-33 35.00 33.00 TL $9,813x 24L5

INDUSTRIAL, SOLID

(Life =SOLID, HIGH PERFORMANCE, OIL RESISTANT/STATI 5000 hrs )

IPPO5 10-3-61/4 Grip 3.00 10.00 NO $380xIPPO4 10-31/2-6 3.50 10.00 NO $294xIPPO18 12-31/2-8 3.50 12.00 NO $300xIPPO23 13-31/2-8 3.50 13.00 NO $340xIPPO32 15-31/2-111/4 3.50 15.00 NO $322xIPPO1 81/2-4-4 4.00 8.50 NO $371xIPPO10 10-4-61/2 4.00 10.00 NO $256xIPPO6 10-4-61/4 4.00 10.00 NO $299xIPPO19 12-4-8 4.00 12.00 NO $328xIPPO47 161/4-4-111/4 Lug 4.00 16.25 NO $405xIPPO30 14-41/2-8 4.50 14.00 NO $445xIPPO40 16-41/2-101/2 Lug 4.50 16.00 NO $483xIPPO2 9-5- 5 Grip 5.00 9.00 NO $388xIPPO12 10-5-61/2 5.00 10.00 NO $267xIPPO7 10-5-61/4 5.00 10.00 NO $299xIPPO13 101/2-5-5 5.00 10.50 NO $435xIPPO31 14-5-10 5.00 14.00 NO $408xIPPO33 15-5-111/4 5.00 15.00 NO $393xIPPO38 151/2-5-10 5.00 15.50 NO $457xIPPO41 16-5-101/2 5.00 16.00 NO $505xIPPO48 161/4-5-111/4 5.00 16.25 NO $436xIPPO53 17-5-121/8 5.00 17.00 NO $497xIPPO63 18-5-14 5.00 18.00 NO $444xIPPO58 18-5-121/8 5.00 18.00 NO $528x


EP 1110-1-8, Vol. 130 Nov 09

F-18


PLY (1)


EP 1110-1-8(Vol. 8)7/31/2009

INDUSTRY CODE

APPENDIX F

IPPO68 20-5-16 5.00 20.00 NO $591xIPPO73 21-5-15 5.00 21.00 NO $615xIPPO79 22-5-16 5.00 22.00 NO $657xIPPO8 10-6-61/4 6.00 10.00 NO $360xIPPO14 101/2-6-5 Lug 6.00 10.50 NO $453xIPPO34 15-6-111/4 Grip 6.00 15.00 NO $585xIPPO42 16-6-101/2 6.00 16.00 NO $566xIPPO49 161/4-6-111/4 6.00 16.25 NO $515xIPPO59 18-6-121/8 6.00 18.00 NO $594xIPPO69 20-6-16 6.00 20.00 NO $629xIPPO74 21-6-15 6.00 21.00 NO $769xIPPO80 22-6-16 6.00 22.00 NO $775xIPPO22 12-61/2-8 6.50 12.00 NO $454xIPPO9 10-7-61/4 7.00 10.00 NO $420xIPPO35 15-7-111/4 7.00 15.00 NO $520xIPPO43 16-7-101/2 7.00 16.00 NO $649xIPPO50 161/4-7-111/4 7.00 16.25 NO $641xIPPO60 18-7-121/8 7.00 18.00 NO $619xIPPO70 20-7-16 7.00 20.00 NO $761xIPPO75 21-7-15 7.00 21.00 NO $789xIPPO81 22-7-16 7.00 22.00 NO $931xIPPO94 26-7-20 7.00 26.00 NO $1,164xIPPO36 15-8-111/4 8.00 15.00 NO $622xIPPO61 18-8-121/8 8.00 18.00 NO $727xIPPO66 18-8-14 8.00 18.00 NO $758xIPPO71 20-8-16 8.00 20.00 NO $812xIPPO76 21-8-15 8.00 21.00 NO $962xIPPO82 22-8-16 8.00 22.00 NO $1,004xIPPO37 15-9-111/4 9.00 15.00 NO $828xIPPO67 18-9-14 9.00 18.00 NO $800xIPPO62 18-9-121/8 9.00 18.00 NO $860xIPPO72 20-9-16 9.00 20.00 NO $1,102xIPPO77 21-9-15 9.00 21.00 NO $1,150xIPPO116 22-9-16 9.00 22.00 NO $1,141xIPPO83 22-9-16 9.00 22.00 NO $1,141xIPPO92 22-10-173/4 10.00 22.00 NO $1,380xIPPO84 22-10-16 10.00 22.00 NO $1,543x


EP 1110-1-8, Vol. 130 Nov 09

F-19


PLY (1)


EP 1110-1-8(Vol. 8)

7/31/2009

INDUSTRY CODE

APPENDIX F

IPPO95 28-10-22 10.00 28.00 NO $1,854xIPPO99 36-10-30 10.00 36.00 NO $1,570xIPPO78 21-12-15 12.00 21.00 NO $1,849xIPPO86 22-12-16 12.00 22.00 NO $1,622xIPPO96 28-12-22 12.00 28.00 NO $2,411xIPPO87 22-14-16 14.00 22.00 NO $1,813xIPPO93 22-14-173/4 14.00 22.00 NO $2,096xIPPO88 22-16-16 16.00 22.00 NO $1,998xIPPO98 28-16-22 16.00 28.00 NO $3,423x

CONVEYOR/LOADER BELTING

(Life =CONVEYOR BELTING (GOODYEAR EP) 5000 hrs )

AZZA1 Conveyor Belting 24.00 50.00 NO $610x 2AZZA2 Conveyor Belting 24.00 60.00 NO $731x 2AZZA3 Conveyor Belting 24.00 70.00 NO $854x 2AZZA4 Conveyor Belting 24.00 80.00 NO $975x 2AZZA5 Conveyor Belting 24.00 90.00 NO $1,098x 2AZZA6 Conveyor Belting 24.00 100.00 NO $1,219x 2AZZA7 Conveyor Belting 24.00 110.00 NO $1,341x 2AZZA8 Conveyor Belting 24.00 120.00 NO $1,463x 2AZZA9 Conveyor Belting 24.00 130.00 NO $1,585x 2AZZA10 Conveyor Belting 24.00 140.00 NO $1,707x 2AZZA11 Conveyor Belting 24.00 150.00 NO $1,829x 2AZZA12 Conveyor Belting 30.00 50.00 NO $762x 2AZZA13 Conveyor Belting 30.00 60.00 NO $914x 2AZZA14 Conveyor Belting 30.00 70.00 NO $1,067x 2AZZA15 Conveyor Belting 30.00 80.00 NO $1,219x 2AZZA16 Conveyor Belting 30.00 90.00 NO $1,372x 2AZZA17 Conveyor Belting 30.00 100.00 NO $1,524x 2AZZA18 Conveyor Belting 30.00 110.00 NO $1,677x 2AZZA19 Conveyor Belting 30.00 120.00 NO $1,829x 2AZZA20 Conveyor Belting 30.00 130.00 NO $1,981x 2AZZA21 Conveyor Belting 30.00 140.00 NO $2,134x 2AZZA22 Conveyor Belting 30.00 150.00 NO $2,286x 2AZZA23 Conveyor Belting 36.00 50.00 NO $914x 2AZZA24 Conveyor Belting 36.00 60.00 NO $1,098x 2AZZA25 Conveyor Belting 36.00 70.00 NO $1,280x 2


EP 1110-1-8, Vol. 130 Nov 09

F-20


PLY (1)


EP 1110-1-8(Vol. 8)7/31/2009

INDUSTRY CODE

APPENDIX F

AZZA26 Conveyor Belting 36.00 80.00 NO $1,463x 2AZZA27 Conveyor Belting 36.00 90.00 NO $1,646x 2AZZA28 Conveyor Belting 36.00 100.00 NO $1,829x 2AZZA29 Conveyor Belting 36.00 110.00 NO $2,012x 2AZZA30 Conveyor Belting 36.00 120.00 NO $2,195x 2AZZA31 Conveyor Belting 36.00 130.00 NO $2,378x 2AZZA32 Conveyor Belting 36.00 140.00 NO $2,560x 2AZZA33 Conveyor Belting 36.00 150.00 NO $2,743x 2AZZA34 Conveyor Belting 42.00 50.00 NO $1,067x 2AZZA35 Conveyor Belting 42.00 60.00 NO $1,280x 2AZZA36 Conveyor Belting 42.00 70.00 NO $1,493x 2AZZA37 Conveyor Belting 42.00 80.00 NO $1,707x 2AZZA38 Conveyor Belting 42.00 90.00 NO $1,921x 2AZZA39 Conveyor Belting 42.00 100.00 NO $2,134x 2AZZA40 Conveyor Belting 42.00 110.00 NO $2,347x 2AZZA41 Conveyor Belting 42.00 120.00 NO $2,560x 2AZZA42 Conveyor Belting 42.00 130.00 NO $2,774x 2AZZA43 Conveyor Belting 42.00 140.00 NO $2,988x 2AZZA44 Conveyor Belting 42.00 150.00 NO $3,201x 2AZZA45 Conveyor Belting 48.00 50.00 NO $1,458x 3AZZA46 Conveyor Belting 48.00 60.00 NO $1,750x 3AZZA47 Conveyor Belting 48.00 70.00 NO $2,042x 3AZZA48 Conveyor Belting 48.00 80.00 NO $2,333x 3AZZA49 Conveyor Belting 48.00 90.00 NO $2,625x 3AZZA50 Conveyor Belting 48.00 100.00 NO $2,917x 3AZZA51 Conveyor Belting 48.00 110.00 NO $3,209x 3AZZA52 Conveyor Belting 48.00 120.00 NO $3,501x 3AZZA53 Conveyor Belting 48.00 130.00 NO $3,791x 3AZZA54 Conveyor Belting 48.00 140.00 NO $4,083x 3AZZA55 Conveyor Belting 48.00 150.00 NO $4,375x 3AZZA56 Conveyor Belting 60.00 50.00 NO $2,862x 4AZZA57 Conveyor Belting 60.00 60.00 NO $3,434x 4AZZA58 Conveyor Belting 60.00 70.00 NO $4,007x 4AZZA59 Conveyor Belting 60.00 80.00 NO $4,580x 4AZZA60 Conveyor Belting 60.00 90.00 NO $5,153x 4AZZA61 Conveyor Belting 60.00 100.00 NO $5,725x 4AZZA62 Conveyor Belting 60.00 110.00 NO $6,297x 4


EP 1110-1-8, Vol. 130 Nov 09

F-21


PLY (1)


EP 1110-1-8(Vol. 8)

7/31/2009

INDUSTRY CODE

APPENDIX F

AZZA63 Conveyor Belting 60.00 120.00 NO $6,869x 4AZZA64 Conveyor Belting 60.00 130.00 NO $7,442x 4AZZA65 Conveyor Belting 60.00 140.00 NO $8,015x 4AZZA66 Conveyor Belting 60.00 150.00 NO $8,587x 4


EP 1110-1-8, Vol. 130 Nov 09

F-22

APPENDIX G TIRE LIFE AND TIRE WEAR FACTORS

EP 1110-1-8, Vol. 130 Nov 09

G-1

APPENDIX G TIRE LIFE AND TIRE WEAR FACTORS

SECTION I. TIRE WEAR FACTORS The tire wear factors used in this pamphlet are listed in appendix D. The “useful life” of a new tire is the product of Condition Factors (CF) from I through V, the Wheel Position Factor (WPF), the Grade Factor (GF) (for Drive Tires only) and the Miscellaneous Condition (MC). These factors provide a percentage reduction to the maximum tire life. See chapter 2 for tire cost methodology. Condition Factors, Wheel Position Factors, Grade Factor, and Miscellaneous Condition are derived from the Caterpillar Performance Handbook. The factors shown below are examples specifically for a rear dump wagon.

Condition Factors (CF): Average Severe I. Maintenance 0.981 0.763 II. Speed 0.872 0.763 III. Curves 0.981 0.872 IV. Surface Condition 0.981 0.763 V. Loads 1.090 0.709 CF Product of the factors 0.897 0.275 (I x II x III x IV x V)

VI. Wheel Position Factors (WPF): WPF-FT Front Tire (FT) 0.981 0.981 WPF-DTR Drive Tire (DT) - Rear Dump 0.818 0.709 WPF-TT Trailing Tire (TT) 1.090 1.090 VII. Grade Factor (GF) (Drive Tires Only) 0.981 0.763 VIII. Miscellaneous Condition (MC) 1.090 0.981

EP 1110-1-8, Vol. 130 Nov 09

G-2

APPENDIX G TIRE LIFE AND TIRE WEAR FACTORS (Continued)

SECTION I. TIRE WEAR FACTORS (Continued)

Example: Final Tire Wear Factors for Wagon, Rear Dump (See Appendix D, Category W15)

Average Severe Front Tire - Average = (CF = 0.897)(WPF-FT = 0.981)(MC = 1.090) 0.96 Front Tire - Severe = (CF = 0.275)(WPF-FT = 0.981)(MC = 0.927) 0.60 Drive Tire - Average = (CF = 0.897)(WPF-DTR = 0.763)(GF = 0.981)(MC = 1.090) 0.78 Drive Tire - Severe = (CF = 0.275)(WPF-DTR = 0.732)(GF = 0.763)(MC = 0.927) 0.15 Trailing Tire - Average = (CF = 0.897)(WPF-TT = 1.090)(MC = 1.090) 1.07 Trailing Tire - Severe = (CF = 0.275)(WPF-TT = 1.090)(MC = 0.927) 0.29 SECTION II. MAXIMUM TIRE LIFE Maximum tire life is used in the formula to determine tire wear cost and is located in Appendix F by type of tire.

EP 1110-1-8, Vol. 130 Nov 09

G-3


EP 1110-1-8, Vol. 130 Nov 09

G-4

APPENDIX H MANUFACTURER LIST

EP 1110-1-8, Vol. 130 Nov 09

H-1

APPENDIX HMANUFACTURER LIST

EP 1110-1-8(Vol. 8)

7/31/2009

CODE MANUFACTURER

A1 ALLIED-GATOR, INC.-

A2 ASV INC.-

A3 AMERICAN PILEDRIVING EQUIPMENT, INC.-

A4 ATLAS COPCO WAGNER INC.-

AA AMERICAN AUGERS, INC.-

AB ALLMAND BROTHERS INC.-

AC ACE ENTERPRISES-

AD ACKER DRILL COMPANY INC.-

AE AEROIL PRODUCTS COMPANY, INC.-

AF AIRPLACO EQUIPMENT CO., INC.-

AG ARROW-MASTER, INC.-

AH AUTO CRANE CO.-

AI AMIDA INDUSTRIES, INC.-

AJ ALLEN ENGINEERING CORP.-

AK TYLER EQUIPMENT CO.-

AL ALLENTOWN EQUIPMENT-

AM AMERICAN CRANE CORPORATION (TEREX)-

AN ATLANTIC-

AO ALKOTA CLEANING SYSTEMS, INC.-

AP PECCO AND WOLFF TOWER CRANES (MORROW)-

AQ AQUATICS UNLIMITED-

AR AMERICAN ROAD MACHINERY, INC.-

AS ATLAS COPCO CONSTRUCTION TOOLS INC.-

AT ANDERSON MAVOR INC.-

AU ALLIED CONSTRUCTION PRODUCTS-

AV ALIVA LTD.-

AW AIRMAN (HOKUETSU INDUSTRIES CO. LTD.)-

AX AMERICAN COMPACTION EQUIPMENT, INC.-

H-1

EP 1110-1-8, Vol. 130 Nov 09

H-2


EP 1110-1-8(Vol. 8)7/31/2009

CODE MANUFACTURER

AY KOMLINE-SANDERSON ENGINEERING CO.-

AZ ALLIS-CHALMERS CORP.-

BA BADGER EQUIPMENT CO.-

BB BASCO-

BC BOCK ENGINEERED PRODUCTS, INC.-

BD BRODERSON MANUFACTURING CORPORATION-

BE INGERSOLL RAND MATERIAL HANDLING-

BF BENFORD-

BG BARBER-GREENE COMPANY-

BI BOR-IT MANUFACTURING COMPANY INC.-

BJ BURKEEN MANUFACTURING CO.-

BK BLAW KNOX CONSTRUCTION EQUIPMENT CORP.-

BL US FILTER/BLASTRAC-

BM BROCE MANUFACTURING COMPANY-

BN BANDIT INDUSTRIES, INC.-

BO COMPACTION AMERICA (BOMAG)-

BQ BELL EQUIPMENT NORTH AMERICA INC .-

BR BROOKVILLE MINING EQUIPMENT CORP.-

BS BALDERSON, INC.-

BT BREAKER TECHNOLOGY INC.-

BU BUSH HOG-

BW BOWIE INDUSTRIES, INC.-

BX BIL-JAX, INC.-

C1 COYOTE LOADER SALES, INC.-

C2 CARELIFT EQUIPMENT-

C3 TIME CONDOR CORPORATION-

C4 CATERPILLAR LIFT TRUCKS,-

C5 Construction Equipment Company-

H-2

EP 1110-1-8, Vol. 130 Nov 09

H-3


EP 1110-1-8(Vol. 8)

7/31/2009

CODE MANUFACTURER

CA CATERPILLAR INC. ( MACHINE DIVISION)-

CB CONSOLIDATED BALING MACHINE COMPANY, INC-

CC CEMEN TECH-

CD CDS GROUP-

CE ATHEY PRODUCTS CORPORATION-

CF CGR COMPACTING-

CG CHEMGROUT, INC.-

CH CHAMPION ROAD MACHINERY-PRO PAV (WIRTGEN-

CI CHIPMORE MANUFACTURING CO., INC.-

CJ COLD JET-

CK CHICAGO PNEUMATIC TOOL CO.-

CL CON-E-CO-

CM CLEMCO INDUSTRIES CORPORATION-

CN CEMEN TECH, INC.-

CO WASTE CONTROL SYSTEMS, INC.-

CP CRISAFULLI PUMP-

CQ CUSHION CUT, INC.-

CR CAMLEVER-

CS CASE CORPORATION-

CT CLEVELAND TRENCHER-

CU WASTEQUIP CUSCO INDUSTRIES-

CV CONMACO, INC.-

CW TEREX - CMI (TEREX ROADBUILDING)-

CX CMC (CONSTRUCTION MACHINERY COMPANY)-

CY CENTRIC-

CZ CLYDE IRON WORKS-

DA ELCO INTERNATIONAL INC.-

DD DELTA DREDGE & PUMP CORP.-

H-3

EP 1110-1-8, Vol. 130 Nov 09

H-4


EP 1110-1-8(Vol. 8)7/31/2009

CODE MANUFACTURER

DE DEMOLITION TECHNOLOGIES-

DF DURA FLOAT-

DG DAINONG HEAVY INDUSTRIES, INC.-

DH DAEWOO HEAVY INDUSTRIES LTD.-

DI DICKSON INDUSTRIES INC.-

DJ CATERPILLAR/DJB-

DL PILECO, INC.-

DO DOSCO CORPORATION-

DR DRESSER MINING EQUIPMENT-

DS DREDGING SUPPLY COMPANY (DSC)-

DT DRILTECH, INC. (SANDVIK)-

DW DITCH WITCH(The Charles Machine Works)I-

DY DYNAPAC DIVISION - SVEDALA INDUSTRIES-

EA EAGER BEAVER-

EC ELGIN SWEEPER COMPANY-

ED EQUIPMENT DEVELOPMENT CO., INC. (EDCO)-

EI EIMCO JARVIS CLARK-

EJ CEDARAPIDS INC., A TEREX COMPANY-

EL ELLICOTT MACHINE CORPORATION-

EM EXCEL MACHINERY LTD.-

EP ENVIRO-PAK-

ES ESCO CORPORATION-

ET E. D. ETNYRE & CO.-

EU EUCLID INDUSTRIES, INC.-

EX EXCEL INDUSTRIES, INC.-

EZ E-Z DRILL, INC.-

FC FERMEC NORTH AMERICA LTD., A TEREX CO.-

FE FELKER (TARGET)-

H-4

EP 1110-1-8, Vol. 130 Nov 09

H-5


EP 1110-1-8(Vol. 8)

7/31/2009

CODE MANUFACTURER

FG FINN CORPORATION-

FH FRUEHAUF TRAILER CORPORATION-

FI FIATALLIS-

FK FRANKLIN TREEFARMER-

FL FLETCHER MINING EQUIPMENT-

FN NEW HOLLAND NORTH AMERICA, INC.-

FO FORD MOTOR COMPANY-

FR FERGUSON MANUFACTURING & EQUIPMENT-

FS FIVE STAR MANUFACTURING CO/ELGIN SWEEPER-

FU FURUKAWA CO.,LTD.-

GA GRADALL COMPANY-

GB GAR-BRO MANUFACTURING COMPANY-

GC GEHL COMPANY-

GD GARDNER-DENVER INDUSTRIAL MACHINES-

GE GENSCO AMERICA CO. LTD.-

GF GRIFFIN DEWATERING CORP.-

GH GEITH INC.-

GI GALION DIVISION-

GJ GENIE INDUSTRIES-

GL GARLOCK EQUIPMENT CO.-

GM GMC AND CHEVROLET-

GN GALION DUMP BODIES, INC.-

GO GOMACO CORPORATION-

GR GORMAN-RUPP COMPANY-

GT GILCREST EQUIPMENT COMPANY-

GV GROVE CRANES (MANITOWOC)-

GW GROVE MANLIFT (JLG)-

HA HAZCO SERVICES, INC.-

H-5

EP 1110-1-8, Vol. 130 Nov 09

H-6


EP 1110-1-8(Vol. 8)7/31/2009

CODE MANUFACTURER

HB HAWCO MANUFACTURING COMPANY, LLC-

HC HAMM COMPACTORS, INC.-

HD HYDRAULIC POWER SYSTEMS, INC.-

HE HENDRIX MANUFACTURING COMPANY, INC.-

HF HYDRA-MAC INTERNATIONAL, INC.-

HH ESG MANUFACTURING H&H PUMP & DREDGE-

HI HITACHI CONSTRUCTION MACHINERY-

HM H&M VIBRO, INC.-

HN HINO DIESEL TRUCKS (U.S.A.) INC.-

HO RIVERSIDE PUMP MANUFACTURING-

HP COMPACTION AMERICA-

HQ HYPAC COMPACTION EQUIPMENT-

HR HYDROCAL INC.-

HU HYUNDAI CONSTRUCTION EQUIPMENT-

HW HEWITT-ROBINS-

HY HYSTER CO.-

HZ HOFFCO-COMET-

IA INGERSOLL RAND ROTARY-REC COMPRESSOR DIV-

IB INGERSOLL RAND ROTARY DRILL DIV-

IC INTERNATIONAL CONSTRUCTION EQUIPMENT,INC-

ID KOMATSU DRESSER-

IE IDEAL MANUFACTURING, INC.-

IF INGERSOLL RAND PORTABLE COMPRESSOR DIV-

IG INGRAM COMPACTING, LLC-

IH NAVISTAR INTERNATIONAL TRANSPORTATION-

IM INNOVATIVE MATERIAL SYSTEMS, INC. (IMS)-

IN INGERSOLL RAND CO.-

IP INGERSOLL RAND ROAD MACHINERY DIV-

H-6

EP 1110-1-8, Vol. 130 Nov 09

H-7


EP 1110-1-8(Vol. 8)

7/31/2009

CODE MANUFACTURER

IR INGERSOLL RAND ROCK DRILL DIV-

IS INSLEY DIVISION-

IT NAVISTAR INTERNATIONAL CORPORATION-

JC JCB INC.-

JD DEERE & COMPANY-

JE JCL EQUIPMENT CO.-

JL JLG INDUSTRIES, INC.-

JM JEFFREY MINING MACHINERY DIVISION-

JO C. S. JOHNSON COMPANY-

JR JRB COMPANY INC.-

JS JOHNSTON SWEEPER COMPANY-

JU ATI-Bell-

KA KAWASAKI LOADERS, INC.-

KB KOLBERG - PIONEER, INC-

KC KOBELCO AMERICA INC.-

KD K-D MANITOU, INC.-

KE KENWORTH TRUCK COMPANY-

KF KNAPHEIDE MANUFACTURING CO.-

KH KOHLER COMPANY-

KI KLEIN PRODUCTS, INC.-

KK KEENE ENGINEERING INC.-

KL KOLMAN / ATHEY DIV.-

KM Komatsu America International Company-

KN KENT DEMOLITION TOOLS-

KO KOEHRING CRANES, INC.-

KP KOCH-WATER-

KR KORI CORPORATION-

KU KUBOTA TRACTOR CORPORATION-

H-7

EP 1110-1-8, Vol. 130 Nov 09

H-8


EP 1110-1-8(Vol. 8)7/31/2009

CODE MANUFACTURER

KW KERSHAW MFG., CO.-

KZ KEIZER TECHNOLOGIES AMERICAS, INC-

LA LAYTON MANUFACTURING COMPANY-

LB LINK-BELT CONSTRUCTION EQUIPMENT CO.-

LC LINCOLN ELECTRIC COMPANY-

LD LEE-BOY-

LE LELY PACIFIC, INC.-

LF LOFTNESS / US ATTACHMENTS-

LG LITTLE GIANT CRANE & SHOVEL INC.-

LH MORROW EQUIPMENT COMPANY, LLC-

LI LINK-BELT CONSTRUCTION EQUIPMENT COMPANY-

LK LIFTKING INDUSTRIES, INC.-

LL OMNIQUIP, LULL-

LN LONDON MACHINERY INC.-

LO LORAIN CRANES DIVISION-

LS LAKE SHORE MINING EQUIPMENT INC.-

LU LABOUNTY MANUFACTURING,-

LY BOART LONGYEAR COMPANY-

LZ LIEBHERR CONSTRUCTION EQUIPMENT CO.-

M1 MANITEX - MANITOWOC BOOM TRUCKS GROUP-

M2 MAULDIN - CALDER BROTHERS CORP.-

M3 MAYCO PUMP - MULTIQUIP INC.-

M4 MITCHELL INDUSTRIAL TIRE COMPANY (MITCO)-

MA MANITOWOC ENGINEERING CO.-

MB M-B COMPANIES, INC.-

MC VME NORTH AMERICA-

MD MDI/YUTANI-

ME MELROE COMPANY/BOBCAT-

H-8

EP 1110-1-8, Vol. 130 Nov 09

H-9


EP 1110-1-8(Vol. 8)

7/31/2009

CODE MANUFACTURER

MF MF INDUSTRIAL-

MG McMASTER-CARR-

MH MITSUBISHI FUSO TRUCK OF AMERICA-

MI MITSUBISHI CONSTRUCTION EQUIP.-

MJ MILLER SPREADER CO.-

MK MKT MANUFACTURING, INC.-

ML ITT MARLOW PUMPS-

MM MACO-MUEDON-

MN GRANUTE-SATURN SYSTEMS(MAC CORPORATION)-

MO MORGEN MANUFACTURING CO.-

MP MIDLAND MACHINERY CO-

MQ MORBARK, INC.-

MR FOREMOST MOBILE DRILLING COMPANY, INC.-

MS MUSTANG UNITS COMPANY-

MT MACK TRUCKS, INC.-

MU MULTIQUIP, INC.-

MV MAYVILLE ENGINEERING CO., INC.-

MW M-B-W, INC.-

MX MAXON INDUSTRIES-

MY MIDLAND MANUFACTURING INC.-

MZ MARINE INLAND FABRICATORS-

NA NAGANO - LELY CORP.-

NB NASCO EQUIPMENT CO. INC.-

NC NATIONAL CRANE CORPORATION-

NE NEAL MANUFACTURING COMPANY, INC-

NI NIFTYLIFT INC. - USA-

NL NLB CORPORATION-

NO NORTHWEST ENGINEERING COMPANY-

H-9

EP 1110-1-8, Vol. 130 Nov 09

H-10


EP 1110-1-8(Vol. 8)7/31/2009

CODE MANUFACTURER

NP NPK CONSTRUCTION EQUIPMENT-

OE OLIN ENGINEERING, INC.-

OK O & K ORENSTEIN & KOPPEL INC.-

OL OLYMPYK CHAIN SAWS-

ON ONAN CORPORATION-

PA PALFINGER INC.-

PB PETTIBONE MICHIGAN LLC-

PC GETMAN BROTHERS MFG. COMPANY-

PE PETERBILT MOTORS COMPANY-

PH P & H-

PI PIQUA ENGINEERING-

PL PRO-LINE / ANVIL ATTACHMENTS-

PN PEMBERTON, INC.-

PO PROGRESSIVE DEVELOPMENT INC.-

PP PACIFIC RUBBER-

PR USFILTER PERRIN PRODUCTS-

PS POWER CURBERS, INC.-

PT PATENT CONSTRUCTION SYSTEMS-

PU PUTZMEISTER INC.-

PW POWERSCREEN INTERNATIONAL DISTRIBUTION LTD-

RA METSO MINERALS-

RC JOHNSON-ROSS (TEREX ROADBUILDING)-

RD REEDRILL (TEREX)-

RE NORSTAR PRODUCTS INTERNATIONAL, INC.-

RI REYNOLDS INTERNATIONAL, L.P.-

RK RAPID MIX-

RM ROME PLOW CO.-

RN ALLIED SYSTEMS COMPANY (RANGER)-

H-10

EP 1110-1-8, Vol. 130 Nov 09

H-11


EP 1110-1-8(Vol. 8)

7/31/2009

CODE MANUFACTURER

RO ROBBINS COMPANY-

RQ REED MANUFACTURING-

RR RAMMER - GR COSTRUTTORI - SANDVIK-

RS ROSCO, A LeeBoy COMPANY-

RT ROADTEC ( ASTEC INDUSTRIES COMPANY)-

RX RAMMAX MACHINERY CO.-

S1 STANLEY HYDRAULIC TOOLS-

S2 SCHRAMM, INC-

S3 CHAMPION ROAD MACHINERY - SUPERPAC CO.-

S4 SUPERIOR INDUSTRIES, AN ASTEC COMPANY-

S5 SOMAT WASTE REDUCTION TECHNOLOGY-

S6 SUPERIOR TIRE & RUBBER CORP.-

SA SAUERMAN (NATIONAL OILWELL VARCO)-

SB SCAT TRAK - OMNIQUIP - TEXTRON INC.-

SC SCHWING AMERICA INC.-

SD SIOUX STEAM CLEANER CORPORATION-

SE SEALMASTER, INC.-

SF SECO CORPORATION-

SG STONE CONSTRUCTION EQUIPMENT, INC.-

SH SHRED-TECH LIMITED-

SI SAKAI AMERICA, INC.-

SJ SKYJACK, INC.-

SK LTV ENERGY PRODUCTS (SKAGIT)-

SL SHUTTLELIFT, INC.-

SM SEAARK MARINE-

SN STEPHENS MANUFACTURING CO., INC.-

SO SOUTHWEST CONSTRUCTION EQUIPMENT CO.-

SP SPRAGUE AND HENWOOD-

H-11

EP 1110-1-8, Vol. 130 Nov 09

H-12


EP 1110-1-8(Vol. 8)7/31/2009

CODE MANUFACTURER

SQ SCHAEFF INC.-

SR SULLAIR CORPORATION-

SS SAMSUNG CONSTRUCTION EQUIPMENT AMERICA-

ST STOW MANUFACTURING, INC.-

SU SULLIVAN-PALATEK, INC.-

SV SOMERO ENTERPRISES, INC.-

SW SNORKEL-

SX SELLICK EQUIPMENT LIMITED-

SY SKY TRAK - OMNIQUIP - TEXTRON INC.-

SZ STRATO-LIFT INTERNATIONAL CORP.-

TA TAMPO MANUFACTURING CO., INC.-

TB TERRAMITE CONSTRUCTION EQUIPMENT-

TC TCM-

TD TADANO AMERICA CORPORATION-

TE TEREX CORPORATION-

TF THOMAS EQUIPMENT LTD.-

TG TIMBCO HYDRAULICS, INC.-

TH TEEMARK CORPORATION-

TI TIMBERJACK, A JOHN DEERE COMPANY-

TJ TRAMAC-

TK TAKEUCHI MFG. (U.S.), LTD-

TL BREAKER TECHNOLOGY, INC. (AN ASTEC CO.)-

TM TESMEC USA, INC.-

TO TORO-

TR TEREX MINING-

TS TELSMITH INC.-

TT TRAIL KING INDUSTRIES, INC.-

TU TITAN INTERNATIONAL, INC.-

H-12

EP 1110-1-8, Vol. 130 Nov 09

H-13


EP 1110-1-8(Vol. 8)

7/31/2009

CODE MANUFACTURER

TV TRAVERSE LIFT CO.-

UE UNDERGROUND EQUIPMENT & SUPPLY-

UL UNIVERSAL ENGINEERING - SVEDALA - METSO-

UN UNIT RIG-

UP UPRIGHT INC.-

VA VOEST-ALPINE-

VB VIBROMAX AMERICA INC.-

VE VERMEER MANUFACTURING CO.-

VI VINCE HAGAN COMPANY-

VO VOLVO CONSTRUCTION EQUIPMENT GROUP-

VP VOGELE AMERICA - PRO-PAV DIV.-

VS VALLEY SLURRY SEAL / MACROPAVER DIVISION-

VT VALMET - PARTEK FOREST LLC-

VU VULCAN FOUNDATION EQUIPMENT, INC-

WA HAULPAK DIVISION-

WB WEBER MASCHINENTECHNIK GMBH-

WC WACKER CORPORATION-

WD WALDON, INC.-

WE WEATHERFORD U.S. INC.-

WF WATSON INC.-

WG ATLAS COPCO WAGNER-

WH WIGGINS LIFT CO., INC.-

WI WILLMAR EQUIPMENT COMPANY-

WL WALKER MANUFACTURING CO., INC.-

WN WAIN-ROY, INC.-

WO WACO SCAFFOLDING & EQUIPMENT-

WR WARNER FRUEHAUF TRAILER CO., INC.-

WS WHITEMAN CONSPRAY, INC.-

H-13

EP 1110-1-8, Vol. 130 Nov 09

H-14


EP 1110-1-8(Vol. 8)7/31/2009

CODE MANUFACTURER

WT WIRTGEN AMERICAN, INC.-

XX NO SPECIFIC MANUFACTURER-

YA YANMAR DIESEL AMERICA CORP.-

YB ADVANCED ENVIRONMENTAL SOLUTIONS-

ZZ GENERIC EQUIPMENT-

H-14

EP 1110-1-8, Vol. 130 Nov 09

H-15


EP 1110-1-8, Vol. 130 Nov 09

H-16

APPENDIX I FEDERAL COST-OF-MONEY RATE

EP 1110-1-8, Vol. 130 Nov 09

I-1

(Renegotiation or Prompt Payment Rate)

APPENDIX IFEDERAL COST-OF-MONEY RATE

EP 1110-1-8(Vol. 12)

7/31/2009

EFFECTIVE DATE RATEEFFECTIVE MONTHS

JULY - DECEMBER 7.000%7/1/1994

JANUARY - JUNE 8.125%1/1/1995


JANUARY - JUNE 5.875%1/1/1996


JANUARY - JUNE 6.375%1/1/1997


JANUARY - JUNE 6.250%1/1/1998


JANUARY - JUNE 5.000%1/1/1999


JANUARY - JUNE 6.750%1/1/2000


JANUARY - JUNE 6.375%1/1/2001


JANUARY - JUNE 5.500%1/1/2002


JANUARY - JUNE 4.250%1/1/2003


JANUARY - JUNE 4.000%1/1/2004


JANUARY - JUNE 4.250%1/1/2005


JANUARY - JUNE 5.125%1/1/2006


JANUARY - JUNE 5.250%1/1/2007


JANUARY - JUNE 4.750%1/1/2008


JANUARY - JUNE 5.625%1/1/2009


I-1

EP 1110-1-8, Vol. 130 Nov 09

I-2

APPENDIX J EQUIPMENT ACCESSORIES

EP 1110-1-8, Vol. 130 Nov 09

J-1

APPENDIX J EQUIPMENT ACCESSORIES

The following accessories are listed by category (CAT), subcategory (SUB), and description (including features required for safety). The accessories have been included with the major equipment listed in this pamphlet when they are not included with the basic cost and are offered by the manufacturer.

CAT SUB DESCRIPTION C85.10 CRANES, DRAGLINE AND CLAMSHELL, CRAWLER MOUNTED Power load lowering Independent swing and travel Third drum Torque converter [machines 1 1/2 cubic yard (cy) or larger] Approximately one-half maximum boom length Counterweight (standard) Fire extinguisher 5-B:C Swing and reverse signal (backup) alarm Boom angle indicator and a load-indicating device Drum rotation indicators Anti-two block (upper limit) devices Manufacturers’ mandatory accessories C85.20 CRANES, LIFTING, CRAWLER MOUNTED Power load lowering Independent swing and travel Third drum Torque converter (machines 25 tons or larger) One-half maximum boom length (machines less than 60 tons) Maximum boom length at 360 degree rating (machines larger than

60 tons) Counterweight (standard) Fire extinguisher 5-B:C Swing and reverse signal (backup) alarm Boom angle indicator and a load-indicating device Drum rotation indicators Anti-two block (upper limit) devices Manufacturers’ mandatory accessories Hook block on machines larger than 100 tons C90.01 TRUCK CRANES - LESS THAN 25 TONS Power load lowering Third drum

EP 1110-1-8, Vol. 130 Nov 09

J-2

CAT SUB DESCRIPTION Mechanical outriggers with screw jacks Maximum boom length at 360 degrees rating C90.01 TRUCK CRANES - LESS THAN 25 TONS (Continued) Counterweight (standard) Fire extinguisher 5-B:C Swing and reverse signal (backup) alarm Boom angle indicator and a load-indicating device Drum rotation indicators Anti-two block (upper limit) devices Manufacturers mandatory accessories C90.02 TRUCK CRANE - 25 TONS AND LARGER C90.03 Power load lowering C90.04 Third drum Hydraulic outriggers with screw jacks Torque converter when available (upper only) Maximum boom length at 360 degrees rating Counterweight (standard) Fire extinguisher 5-B:C Reverse signal (backup) alarm Boom angle indicator and a load-indicating device Drum rotation indicators Anti-two block (upper limit) devices Hook block on machines larger than 100 tons G15 GRADER Rollover protective structures (ROPS) with enclosed cab Ripper/scarifier, rear mounted Front wheel lean Power circle Hydraulic shift and tilt moldboard End bits Standard work lights Fire extinguisher 5-B:C Reverse signal (backup) alarm H25 EXCAVATORS, HYDRAULIC H30 Backhoe bucket (standard) Backhoe stick (medium length) Backhoe boom (one piece) Backhoe bucket linkage (with cylinder) Guards

EP 1110-1-8, Vol. 130 Nov 09

J-3

CAT SUB DESCRIPTION Counterweight Standard work lights Reverse signal (backup) alarm ROPS Fire extinguisher 5-B:C H35 HYDRAULIC SHOVELS - CRAWLER MOUNTED Torque converter (machines 1 1/2 cy or larger) Counterweight Reverse signal (backup) alarm ROPS Fire extinguisher 5-B:C L30 LOADERS, BELT (CONVEYOR BELTS) Power unit Head pulley clutch and backstop Belt cleaner and belt installing equipment King pin attachments L35 LOADERS, 1 1/2 cy AND LARGER L40 Blower fan Guard, power train Automatic bucket positioner Standard counterweight Machines less than 7 cy: General purpose or excavating bucket

with bolt on cutting edge and no teeth Machines 7 cy or larger: Rock bucket with bolt on cutting edge and

teeth Standard work lights Reverse signal (backup) alarm ROPS Fire extinguisher 5-B:C S10 SCRAPERS S15 Control single lever S20 Blower fan Standard work light Guards, power train Reverse signal (backup) alarm ROPS Fire extinguisher 5-B:C Supplemental steering

EP 1110-1-8, Vol. 130 Nov 09

J-4

CAT SUB DESCRIPTION T15 TRACTOR, CRAWLER Hydraulic controls for ripper and blade Guards Blower fan Standard work lights Hook, front pull Track grousers (severe service for units over 200 hp) Counterweights where required Reverse signal (backup) alarm ROPS Universal blade T20 TRACTOR, WHEEL Hydraulic controls for ripper and blade Guards Blower fan Standard work lights Blade Fire extinguisher 5-B:C Counterweights when required T25 TRACTOR, AGRICULTURAL Independent power take off (PTO) Standard work lights Fire extinguisher 5-B:C Counterweights when required 3-point hitch ROPS Hydraulic system with controls T55 TRUCKS, OFF-HIGHWAY No spin differential Tachograph Engine and transmission guards Body liners

EP 1110-1-8, Vol. 130 Nov 09

J-5


EP 1110-1-8, Vol. 130 Nov 09

J-6

APPENDIX K GROUND ENGAGING COMPONENT COSTS INCLUDED IN REPAIRS (RCF)

EP 1110-1-8, Vol. 130 Nov 09

K-1

CATEGORY

SUB DESCRIPTION EK C DC LIFE SLV RCF

Blade cutting edges, wear plates,

hard facing, and end plates

Ground Engaging Component Costs Included in Repairs (RCF)

EP 1110-1-8

7/31/2009(Vol. 8)

APPENDIX K

Bucket teeth, cutting edges,

side cutters, and wear plates

Ripper tips and shank protection

Equipment Specific Wear

Items

B15 0.00 95 A B 8,000 0.10 0.80BROOMS, STREET SWEEPERS & FLUSHERS

B25 0.00 15 A B 8,000 0.10 0.70BUCKETS, CLAMSHELL

B25 0.00 15 S B 6,500 0.10 0.80BUCKETS, CLAMSHELL

B35 0.00 1BUCKETS, DRAGLINE

B35 0.10 15 A B 8,000 0.10 0.70 LIGHT WEIGHT

B35 0.10 15 S B 6,500 0.10 0.80 LIGHT WEIGHT

B35 0.20 15 A B 9,000 0.10 0.70 MEDIUM WEIGHT

B35 0.20 15 S B 7,000 0.10 0.80 MEDIUM WEIGHT

B35 0.30 15 A B 10,000 0.10 0.70 HEAVY WEIGHT

B35 0.30 15 S B 8,000 0.10 0.80 HEAVY WEIGHT

G15 0.00 35 A B 14,500 0.25 0.75GRADERS, MOTOR

G15 0.00 35 S B 13,500 0.25 0.85GRADERS, MOTOR

H25 0.00 1HYDRAULIC EXCAVATORS, CRAWLER MOUNTED

H25 0.10 65 A B 8,000 0.25 0.70 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS)

H25 0.10 65 S B 7,000 0.25 0.80 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS)

H25 0.11 65 A B 8,500 0.25 0.70 OVER 12,500 LBS THRU 40,000 LBS

H25 0.11 65 S B 7,000 0.25 0.85 OVER 12,500 LBS THRU 40,000 LBS




L- 1

EK=Economic Key (Appendix E) C=Operating Conditions (A=average, S=severe) DC=Discount Code (B=basic 7.5%, S=special 15%) LIFE=Economic Life SLV=Salvage Value RCF=Repair Cost FactorGround Engaging Component (GEC) is defined as those wear items on the machine that come in direct contact with in situ ground to perform the machines primary function. For machines with blades, GEC can include: cutting edges, wear plates, hard facing, and end plates. For machines with buckets, GEC can include: bucket teeth, cutting edges, side cutters, and wear plates. For machines with rippers, GEC can include: tips and shank protectors. Equipment Specific Wear items include those items of wear that are specific to that equipment. Not included in the Repairs and must be added as needed are: drill/bits, drill/steel, roadheader/rock breaking bits, air tools/breaker points/jackhammer points, concrete coring drill bits, and other wear items that are not shown here.

EP 1110-1-8, Vol. 130 Nov 09

K-2

CATEGORY





EP 1110-1-8

7/31/2009(Vol. 8)

APPENDIX K





Items


H25 0.14 65 A B 19,000 0.25 1.10 OVER 160,000 LBS

H25 0.14 65 S B 15,000 0.25 1.25 OVER 160,000 LBS

H30 0.00 1HYDRAULIC EXCAVATORS, WHEEL MOUNTED

H30 0.01 65 A B 8,000 0.25 0.50 0 THRU 1.0 CY

H30 0.01 65 S B 6,500 0.25 0.55 0 THRU 1.0 CY

H30 0.02 65 A B 10,000 0.25 0.60 OVER 1.0 CY

H30 0.02 65 S B 8,000 0.25 0.65 OVER 1.0 CY

H35 0.00 1HYDRAULIC SHOVELS, CRAWLER MOUNTED

H35 0.11 65 A B 14,000 0.20 1.00 DIESEL, 0 CY THRU 5.0 CY

H35 0.11 65 S B 12,000 0.20 1.10 DIESEL, 0 CY THRU 5.0 CY

H35 0.12 65 A B 16,000 0.20 1.20 DIESEL, OVER 5.0 CY

H35 0.12 65 S B 14,000 0.20 1.30 DIESEL, OVER 5.0 CY

H35 0.21 65 A B 18,000 0.20 0.80 ELECTRIC, OVER 2.5 CY

H35 0.21 65 S B 16,000 0.20 0.90 ELECTRIC, OVER 2.5 CY

L35 0.00 40 A B 10,000 0.20 1.10LOADERS, FRONT END, CRAWLER TYPE

L35 0.00 40 S B 8,000 0.20 1.25LOADERS, FRONT END, CRAWLER TYPE

L40 0.00 1LOADERS, FRONT END, WHEEL TYPE

L40 0.11 45 A B 9,250 0.25 0.70 ARTICULATED, 0 THRU 225 HP

L40 0.11 45 S B 8,750 0.25 0.80 ARTICULATED, 0 THRU 225 HP

L- 2


EP 1110-1-8, Vol. 130 Nov 09

K-3

CATEGORY





EP 1110-1-8

7/31/2009(Vol. 8)

APPENDIX K





Items

L40 0.12 45 A B 13,500 0.20 0.70 ARTICULATED, OVER 225 HP

L40 0.12 45 S B 12,000 0.20 0.75 ARTICULATED, OVER 225 HP

L40 0.20 45 A B 8,000 0.20 0.80 SKID STEER

L40 0.31 45 A B 10,000 0.25 0.85 TOOL CARRIER & TELESCOPIC HANDLERS, 0 THRU 225 HP

L40 0.31 45 S B 9,250 0.25 0.90 TOOL CARRIER & TELESCOPIC HANDLERS, 0 THRU 225 HP

L40 0.32 45 A B 12,000 0.15 0.85 TOOL CARRIER & TELESCOPIC HANDLERS, OVER 225 HP

L40 0.32 45 S B 10,000 0.15 0.90 TOOL CARRIER & TELESCOPIC HANDLERS, OVER 225 HP

L45 0.00 40 A B 8,000 0.20 1.35LOADERS / BACKHOE, CRAWLER TYPE

L45 0.00 40 S B 6,000 0.20 1.40LOADERS / BACKHOE, CRAWLER TYPE

L50 0.00 45 A B 10,000 0.25 0.80LOADERS / BACKHOE, WHEEL TYPE

L50 0.00 45 S B 6,000 0.25 0.85LOADERS / BACKHOE, WHEEL TYPE

L60 0.00 75 A B 10,000 0.15 0.70LOG SKIDDERS

L60 0.00 75 S B 8,000 0.15 0.80LOG SKIDDERS

P35 0.00 70 A B 14,000 0.20 0.95PIPELAYERS

P35 0.00 70 S B 11,500 0.20 1.10PIPELAYERS

R30 0.00 1ROLLERS, STATIC, SELF-PROPELLED

R30 0.03 55 A B 12,000 0.20 0.80 TAMPING FOOT, LANDFILL & SOIL COMPACTORS

S10 0.00 1SCRAPERS, ELEVATING

S10 0.01 60 A B 10,000 0.20 0.90 0 THRU 200 HP

S10 0.01 60 S B 8,000 0.20 1.00 0 THRU 200 HP

L- 3


EP 1110-1-8, Vol. 130 Nov 09

K-4

CATEGORY





EP 1110-1-8

7/31/2009(Vol. 8)

APPENDIX K





Items

S10 0.02 60 A B 13,000 0.25 0.95 OVER 200 HP

S10 0.02 60 S B 11,500 0.25 1.00 OVER 200 HP

S15 0.00 60 A B 15,000 0.20 0.80SCRAPERS, CONVENTIONAL

S15 0.00 60 S B 12,500 0.20 0.85SCRAPERS, CONVENTIONAL

S20 0.00 60 A B 15,000 0.20 0.85SCRAPERS, TANDEM POWERED

S20 0.00 60 S B 13,500 0.20 0.90SCRAPERS, TANDEM POWERED

S25 0.00 60 A B 12,000 0.20 0.70SCRAPERS, TRACTOR DRAWN

S25 0.00 60 S B 10,000 0.20 0.75SCRAPERS, TRACTOR DRAWN

T15 0.00 1TRACTORS, CRAWLER (DOZER) (includes blade)

T15 0.01 70 A B 10,000 0.30 1.10 0 THRU 225 HP

T15 0.01 70 S B 8,000 0.30 1.25 0 THRU 225 HP

T15 0.02 70 A B 12,500 0.25 1.20 226 HP THRU 425 HP

T15 0.02 70 S B 10,500 0.25 1.25 226 HP THRU 425 HP

T15 0.03 70 A B 15,000 0.20 1.20 OVER 425 HP

T15 0.03 70 S B 12,500 0.20 1.35 OVER 425 HP

T20 0.00 75 A B 14,000 0.15 0.60TRACTORS, WHEEL TYPE (DOZER)

T20 0.00 75 S B 13,000 0.15 0.65TRACTORS, WHEEL TYPE (DOZER)

L- 4


EP 1110-1-8, Vol. 130 Nov 09

K-5


EP 1110-1-8, Vol. 130 Nov 09

K-6

APPENDIX L GUIDE FOR ESTIMATING DRILL STEEL AND DRILL BIT COSTS

EP 1110-1-8, Vol. 130 Nov 09

L-1

Guide for Estimating Drill Steel and Drill Bit Costs

Prepared for the US Army Corps of Engineers, Walla Walla District By Western Mine Engineering, Inc in cooperation

with Aventurine Engineering, Inc. 2006

August 2006

EP Octpb

L-2

EP 1110-1-8, Vol. 130 Nov 09

Cost Assumptions for Drill Steel and Drill Bit

General: The approach to defining the scope of this cost guide was to confine the work to the basic drilling process and attendant drill bit and steel lives and costs. This not only simplified the study parameters but also ensured that future users of the study results could readily modify the data to suit their individual needs.

1. The steel costs reflect the cost of drilling steel only. All ancillary equipment such as

couplings, striking bars, and hammer maintenance items were not included.

2. The bit life is indicative of the total life of each bit to include up to 10 sharpenings/grindings per bit. The bit costs, however, are list prices for each bit and do not reflect the costs associated with this process.

3. Costs for both bits and steel are list pricing based on manufacturers’ catalogs or

quotes. No additional materials, equipment costs, or other associated costs are included. No discounts were applied to the catalog list prices. Estimators will have to determine an appropriate discount for their individual cases. All prices are based on current, 2006 costs.

4. The bit and steel lives and penetration rates are based on time the bit is engaged in

the hole. Adjustment for setup, tear down, and moving time between holes has not been considered.

5. Appropriate bits were identified primarily by drill type and then list prices were

determined from manufacturers’ catalogs. All bits were button type; with threaded button bits used for the top hammer percussion drills, down the hole (DTH) button bits for “DTH” drills, and tungsten carbide button, roller bits selected for rotary drills.

6. Large rotary drills often use 20' or longer drilling steel. It was our belief that most

situations Corps of Engineers estimators face will fall in the range of percussion or smaller “DTH” drills. In these instances the 12' rod is appropriate. Cursory review of the costs of longer steel rods suggest that costs for a specific drill steel diameter do not vary dramatically on a per foot basis for longer rods. Therefore, the assumption is made that a direct conversion to cost per rod for longer lengths can be made in proportion to the cost for a 12' length rod. For further information, see the note at the lower right corner of each of the spreadsheets for a detailed procedure to make the conversion for rod length and hole depth.

EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-3

Example of Estimating Drill Steel and Drill Bit Costs

General: The approach is to define the scope of the work and determine an estimated cost for drill steel and bits from the answers to the questions below. Follow the simplified steps to arrive at the estimated costs. Determine parameters:

1. Determine the type of drilling method – percussion, down the hole (DTH), or rotary.

2. Determine the manufacturer and model of drilling equipment or determine

equivalency of equipment used in this guide.

3. Determine the material that will be drilled through.

4. Determine the hole diameter of drill.

5. Determine the length of drill rod required to drill hole to the required depth. Determine costs: (This is an example on how to determine costs)

1. Determine the type of drilling method – down the hole (DTH).

2. Determine the manufacturer/model of drilling equipment – Atlas Copco DM25SP.

3. Determine the material that will be drilled - Basalt .

4. Determine the hole diameter of drill – 5”.

5. Determine the length of drill rod required – 90 feet.

6. Calculate drill steel costs from cost tables:

a. Cost of drill steel $/foot per rod ranges $0.034 to $0.025 will use $0.034.

b. Based on 90’ of drilling at 12’ lengths of drill rod – (90’/12’) = 7.5 rods are required. Round up to next whole number = 8 rods.

c. From drill steel cost adjustment factor chart: for 8 rods the factor is 4.5. d. From instructions: $0.034 X 4.5 = $0.1530/lf of hole drilled.

7. Determine drill bit costs from cost tables – costs range from $0.55 to $0.40/lf.

EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-4

DRILL MODEL - Atlas Copco ROC D5 - percussion

Bit Life (feet/bit) Bit Cost ($/foot)

1.75 2.00 2.50 1.75 2.00 2.50Granite 1,506 - 2,037 1,449 - 1,960 1,359 - 1,838 Granite $0.04 - $0.03 $0.05 - $0.04 $0.07 - $0.05Basalt 674 - 912 649 - 878 608 - 823 Basalt $0.09 - $0.07 $0.11 - $0.08 $0.16 - $0.12Gabbro 1,002 - 1,356 964 - 1,305 904 - 1,223 Gabbro $0.06 - $0.05 $0.07 - $0.05 $0.11 - $0.08Shale 1,427 - 1,931 1,373 - 1,858 1,287 - 1,742 Shale $0.04 - $0.03 $0.05 - $0.04 $0.08 - $0.06Sandstone 524 - 709 504 - 682 473 - 639 Sandstone $0.12 - $0.09 $0.14 - $0.10 $0.21 - $0.15Siltstone 3,779 - 5,112 3,636 - 4,919 3,409 - 4,612 Siltstone $0.02 - $0.01 $0.02 - $0.01 $0.03 - $0.02Conglomer 292 - 395 281 - 380 263 - 356 Conglomer $0.21 - $0.16 $0.25 - $0.18 $0.37 - $0.28Breccia 2,181 - 2,951 2,099 - 2,839 1,968 - 2,662 Breccia $0.03 - $0.02 $0.03 - $0.02 $0.05 - $0.04Limestone 1,835 - 2,483 1,766 - 2,389 1,656 - 2,240 Limestone $0.03 - $0.02 $0.04 - $0.03 $0.06 - $0.04Schist 3,414 - 4,619 3,285 - 4,444 3,080 - 4,167 Schist $0.02 - $0.01 $0.02 - $0.02 $0.03 - $0.02Slate 1,710 - 2,313 1,645 - 2,226 1,542 - 2,087 Slate $0.04 - $0.03 $0.04 - $0.03 $0.06 - $0.05Gneiss 735 - 995 707 - 957 663 - 897 Gneiss $0.08 - $0.06 $0.10 - $0.07 $0.15 - $0.11

Drill Steel Life (feet/rod) Drill Steel Cost ($/foot per rod)

1.75 2.00 2.50 1.75 2.00 2.50Granite 2,720 - 3,680 2,617 - 3,541 2,454 - 3,320 Granite $0.103 - $0.076 $0.107 - $0.079 $0.132 - $0.098Basalt 1,417 - 1,918 1,364 - 1,845 1,279 - 1,730 Basalt $0.198 - $0.146 $0.205 - $0.152 $0.253 - $0.187Gabbro 1,600 - 2,164 1,539 - 2,083 1,443 - 1,953 Gabbro $0.175 - $0.129 $0.182 - $0.134 $0.224 - $0.166Shale 2,855 - 3,863 2,747 - 3,717 2,576 - 3,485 Shale $0.098 - $0.072 $0.102 - $0.075 $0.126 - $0.093Sandstone 2,978 - 4,029 2,865 - 3,877 2,687 - 3,635 Sandstone $0.094 - $0.069 $0.098 - $0.072 $0.121 - $0.089Siltstone 2,964 - 4,011 2,852 - 3,859 2,674 - 3,618 Siltstone $0.094 - $0.070 $0.098 - $0.073 $0.121 - $0.090Conglomer 3,425 - 4,633 3,295 - 4,458 3,090 - 4,180 Conglomer $0.082 - $0.060 $0.085 - $0.063 $0.105 - $0.078Breccia 4,739 - 6,412 4,560 - 6,170 4,276 - 5,785 Breccia $0.059 - $0.044 $0.061 - $0.045 $0.076 - $0.056Limestone 3,931 - 5,318 3,782 - 5,117 3,546 - 4,798 Limestone $0.071 - $0.053 $0.074 - $0.055 $0.091 - $0.068Schist 4,828 - 6,532 4,646 - 6,285 4,356 - 5,893 Schist $0.058 - $0.043 $0.060 - $0.045 $0.074 - $0.055Slate 3,133 - 4,239 3,015 - 4,079 2,827 - 3,824 Slate $0.089 - $0.066 $0.093 - $0.069 $0.115 - $0.085Gneiss 2,849 - 3,855 2,742 - 3,709 2,571 - 3,478 Gneiss $0.098 - $0.073 $0.102 - $0.075 $0.126 - $0.093

(Based on 12 foot drilling rod length.)

Penetration Rate (feet/hour) Drill Steel Cost Adjustment FactorAs this study is based on 12 foot drilling rod length,

1.75 2.00 2.50 Number of rods Factor the total steel cost per foot of hole drilled dependsGranite 98 - 132 83 - 113 64 - 86 upon the total number of 12 foot sections in the hole.Basalt 57 - 77 48 - 65 37 - 50 1 1.0 Divide the total hole length by 12 and round this resultGabbro 63 - 85 53 - 72 41 - 55 2 1.5 up to the next whole number to determine number of Shale 102 - 138 87 - 117 66 - 90 3 2.0 rods required to drill the hole. Adjust this number to theSandstone 105 - 142 90 - 121 69 - 93 4 2.5 average number of rods during drilling by consultingSiltstone 105 - 142 89 - 121 68 - 92 5 3.0 the Drill Steel Cost Adjustment Factor table to the left.Conglomer 118 - 160 101 - 136 77 - 104 6 3.5 Multiply this adjustment factor times the cost per footBreccia 155 - 210 132 - 179 101 - 137 7 4.0 per rod from the table above. The result is the totalLimestone 133 - 180 113 - 153 86 - 117 8 4.5 drill steel cost per foot of hole drilled. Other drillSchist 158 - 213 134 - 181 103 - 139 9 5.0 steel lengths may be adjusted for by determining theSlate 110 - 149 94 - 127 72 - 97 10 5.5 total length of rods required and then converting that Gneiss 102 - 137 86 - 117 66 - 89 n (n+1)/2 to the number of equivalent 12 foot sections. Once

this is determined follow the procedure outlined above.

Prepared by Western Mine Division, InfoMine USA, Inc. in cooperation with Aventurine Engineering, Inc. 2006

Hole Diameter (inches)





EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-5

DRILL MODEL - Atlas Copco ROC D7 - percussion


2.50 3.00 4.00 2.50 3.00 4.00Granite 1,203 - 1,628 1,115 - 1,509 1,050 - 1,421 Granite $0.08 - $0.06 $0.12 - $0.09 $0.21 - $0.16Basalt 539 - 729 499 - 676 470 - 636 Basalt $0.18 - $0.13 $0.26 - $0.19 $0.47 - $0.35Gabbro 801 - 1,083 742 - 1,004 699 - 946 Gabbro $0.12 - $0.09 $0.18 - $0.13 $0.32 - $0.24Shale 1,140 - 1,542 1,057 - 1,430 995 - 1,347 Shale $0.09 - $0.06 $0.12 - $0.09 $0.22 - $0.17Sandstone 418 - 566 388 - 525 365 - 494 Sandstone $0.23 - $0.17 $0.34 - $0.25 $0.61 - $0.45Siltstone 3,019 - 4,084 2,798 - 3,786 2,636 - 3,566 Siltstone $0.03 - $0.02 $0.05 - $0.03 $0.08 - $0.06Conglomer 233 - 315 216 - 292 204 - 275 Conglomer $0.42 - $0.31 $0.61 - $0.45 $1.10 - $0.81Breccia 1,742 - 2,357 1,615 - 2,186 1,521 - 2,058 Breccia $0.06 - $0.04 $0.08 - $0.06 $0.15 - $0.11Limestone 1,466 - 1,983 1,359 - 1,839 1,280 - 1,732 Limestone $0.07 - $0.05 $0.10 - $0.07 $0.17 - $0.13Schist 2,727 - 3,690 2,528 - 3,421 2,381 - 3,222 Schist $0.04 - $0.03 $0.05 - $0.04 $0.09 - $0.07Slate 1,366 - 1,848 1,266 - 1,713 1,193 - 1,613 Slate $0.07 - $0.05 $0.10 - $0.08 $0.19 - $0.14Gneiss 587 - 795 544 - 737 513 - 694 Gneiss $0.17 - $0.12 $0.24 - $0.18 $0.43 - $0.32


2.50 3.00 4.00 2.50 3.00 4.00Granite 2,173 - 2,940 2,014 - 2,725 1,897 - 2,567 Granite $0.129 - $0.095 $0.161 - $0.119 $0.215 - $0.159Basalt 1,132 - 1,532 1,050 - 1,420 989 - 1,338 Basalt $0.247 - $0.183 $0.309 - $0.228 $0.412 - $0.304Gabbro 1,278 - 1,729 1,185 - 1,603 1,116 - 1,510 Gabbro $0.219 - $0.162 $0.273 - $0.202 $0.365 - $0.270Shale 2,281 - 3,086 2,115 - 2,861 1,992 - 2,695 Shale $0.123 - $0.091 $0.153 - $0.113 $0.204 - $0.151Sandstone 2,379 - 3,218 2,205 - 2,984 2,077 - 2,810 Sandstone $0.118 - $0.087 $0.147 - $0.109 $0.196 - $0.145Siltstone 2,368 - 3,204 2,195 - 2,970 2,068 - 2,798 Siltstone $0.118 - $0.087 $0.148 - $0.109 $0.197 - $0.145Conglomer 2,736 - 3,701 2,536 - 3,431 2,389 - 3,232 Conglomer $0.102 - $0.076 $0.128 - $0.094 $0.170 - $0.126Breccia 3,786 - 5,122 3,510 - 4,749 3,306 - 4,473 Breccia $0.074 - $0.055 $0.092 - $0.068 $0.123 - $0.091Limestone 3,140 - 4,249 2,911 - 3,939 2,742 - 3,710 Limestone $0.089 - $0.066 $0.111 - $0.082 $0.148 - $0.110Schist 3,857 - 5,218 3,576 - 4,838 3,368 - 4,556 Schist $0.073 - $0.054 $0.091 - $0.067 $0.121 - $0.089Slate 2,503 - 3,386 2,320 - 3,139 2,185 - 2,957 Slate $0.112 - $0.083 $0.140 - $0.103 $0.186 - $0.138Gneiss 2,276 - 3,080 2,110 - 2,855 1,987 - 2,689 Gneiss $0.123 - $0.091 $0.154 - $0.113 $0.205 - $0.151

(Based on12 foot drilling rod length.)










EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-6

DRILL MODEL - Atlas Copco ECM590 - percussion


2.50 3.50 4.50 2.50 3.50 4.50Granite 1,168 - 1,580 1,060 - 1,434 986 - 1,334 Granite $0.08 - $0.06 $0.15 - $0.11 $0.27 - $0.20Basalt 523 - 708 475 - 642 441 - 597 Basalt $0.19 - $0.14 $0.34 - $0.25 $0.61 - $0.45Gabbro 778 - 1,052 706 - 955 656 - 888 Gabbro $0.13 - $0.09 $0.23 - $0.17 $0.41 - $0.30Shale 1,107 - 1,498 1,005 - 1,359 934 - 1,264 Shale $0.09 - $0.07 $0.16 - $0.12 $0.29 - $0.21Sandstone 406 - 550 369 - 499 343 - 464 Sandstone $0.24 - $0.18 $0.43 - $0.32 $0.78 - $0.58Siltstone 2,931 - 3,966 2,660 - 3,599 2,474 - 3,347 Siltstone $0.03 - $0.02 $0.06 - $0.04 $0.11 - $0.08Conglomer 226 - 306 205 - 278 191 - 259 Conglomer $0.43 - $0.32 $0.77 - $0.57 $1.40 - $1.04Breccia 1,692 - 2,289 1,535 - 2,077 1,428 - 1,932 Breccia $0.06 - $0.04 $0.10 - $0.08 $0.19 - $0.14Limestone 1,424 - 1,926 1,292 - 1,748 1,201 - 1,626 Limestone $0.07 - $0.05 $0.12 - $0.09 $0.22 - $0.16Schist 2,648 - 3,583 2,403 - 3,251 2,235 - 3,024 Schist $0.04 - $0.03 $0.07 - $0.05 $0.12 - $0.09Slate 1,326 - 1,794 1,203 - 1,628 1,119 - 1,514 Slate $0.07 - $0.05 $0.13 - $0.10 $0.24 - $0.18Gneiss 570 - 771 517 - 700 481 - 651 Gneiss $0.17 - $0.13 $0.31 - $0.23 $0.56 - $0.41


2.50 3.50 4.50 2.50 3.50 4.50Granite 2,110 - 2,855 1,915 - 2,590 1,781 - 2,409 Granite $0.154 - $0.114 $0.213 - $0.157 $0.229 - $0.169Basalt 1,100 - 1,488 998 - 1,350 928 - 1,255 Basalt $0.295 - $0.218 $0.408 - $0.302 $0.439 - $0.324Gabbro 1,241 - 1,679 1,126 - 1,524 1,047 - 1,417 Gabbro $0.261 - $0.193 $0.361 - $0.267 $0.389 - $0.287Shale 2,215 - 2,997 2,010 - 2,719 1,869 - 2,529 Shale $0.146 - $0.108 $0.202 - $0.150 $0.218 - $0.161Sandstone 2,310 - 3,125 2,096 - 2,836 1,950 - 2,638 Sandstone $0.140 - $0.104 $0.194 - $0.144 $0.209 - $0.154Siltstone 2,300 - 3,111 2,087 - 2,823 1,941 - 2,626 Siltstone $0.141 - $0.104 $0.195 - $0.144 $0.210 - $0.155Conglomer 2,657 - 3,594 2,411 - 3,262 2,242 - 3,033 Conglomer $0.122 - $0.090 $0.169 - $0.125 $0.182 - $0.134Breccia 3,676 - 4,974 3,336 - 4,514 3,103 - 4,198 Breccia $0.088 - $0.065 $0.122 - $0.090 $0.131 - $0.097Limestone 3,049 - 4,125 2,767 - 3,744 2,573 - 3,482 Limestone $0.106 - $0.079 $0.147 - $0.109 $0.158 - $0.117Schist 3,745 - 5,067 3,399 - 4,598 3,161 - 4,277 Schist $0.087 - $0.064 $0.120 - $0.089 $0.129 - $0.095Slate 2,430 - 3,288 2,205 - 2,984 2,051 - 2,775 Slate $0.133 - $0.099 $0.185 - $0.136 $0.198 - $0.147Gneiss 2,210 - 2,990 2,006 - 2,714 1,865 - 2,524 Gneiss $0.147 - $0.108 $0.203 - $0.150 $0.218 - $0.161

(Based pm 12 foot drilling rod length.)










EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-7

DRILL MODEL - Atlas Copco ECM720 - percussion


4.00 4.50 5.00 4.00 4.50 5.00Granite 2,305 - 3,118 2,228 - 3,014 2,161 - 2,924 Granite $0.10 - $0.07 $0.12 - $0.09 $0.15 - $0.11Basalt 1,032 - 1,396 997 - 1,349 967 - 1,309 Basalt $0.22 - $0.16 $0.27 - $0.20 $0.33 - $0.25Gabbro 1,534 - 2,075 1,483 - 2,006 1,438 - 1,946 Gabbro $0.15 - $0.11 $0.18 - $0.13 $0.22 - $0.16Shale 2,184 - 2,955 2,111 - 2,856 2,048 - 2,771 Shale $0.10 - $0.08 $0.13 - $0.09 $0.16 - $0.12Sandstone 802 - 1,085 775 - 1,048 752 - 1,017 Sandstone $0.28 - $0.21 $0.35 - $0.26 $0.43 - $0.32Siltstone 5,783 - 7,824 5,589 - 7,562 5,422 - 7,336 Siltstone $0.04 - $0.03 $0.05 - $0.04 $0.06 - $0.04Conglomer 447 - 604 432 - 584 419 - 567 Conglomer $0.50 - $0.37 $0.62 - $0.46 $0.77 - $0.57Breccia 3,338 - 4,516 3,227 - 4,365 3,130 - 4,235 Breccia $0.07 - $0.05 $0.08 - $0.06 $0.10 - $0.08Limestone 2,809 - 3,800 2,715 - 3,673 2,633 - 3,563 Limestone $0.08 - $0.06 $0.10 - $0.07 $0.12 - $0.09Schist 5,225 - 7,069 5,050 - 6,833 4,899 - 6,628 Schist $0.04 - $0.03 $0.05 - $0.04 $0.07 - $0.05Slate 2,617 - 3,540 2,529 - 3,422 2,453 - 3,319 Slate $0.09 - $0.06 $0.11 - $0.08 $0.13 - $0.10Gneiss 1,125 - 1,522 1,087 - 1,471 1,055 - 1,427 Gneiss $0.20 - $0.15 $0.25 - $0.18 $0.30 - $0.22













EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-8

DRILL MODEL - Atlas Copco DM25SP - DTH


3.50 5.00 6.50 3.50 5.00 6.50Granite 2,498 - 3,380 2,254 - 3,049 2,089 - 2,827 Granite $0.16 - $0.12 $0.24 - $0.18 $0.31 - $0.23Basalt 1,118 - 1,513 1,009 - 1,365 935 - 1,266 Basalt $0.37 - $0.27 $0.55 - $0.40 $0.68 - $0.51Gabbro 1,663 - 2,250 1,500 - 2,030 1,391 - 1,882 Gabbro $0.25 - $0.18 $0.37 - $0.27 $0.46 - $0.34Shale 2,367 - 3,203 2,136 - 2,890 1,980 - 2,679 Shale $0.17 - $0.13 $0.26 - $0.19 $0.32 - $0.24Sandstone 869 - 1,176 784 - 1,061 727 - 983 Sandstone $0.47 - $0.35 $0.70 - $0.52 $0.88 - $0.65Siltstone 6,268 - 8,481 5,655 - 7,651 5,243 - 7,093 Siltstone $0.07 - $0.05 $0.10 - $0.07 $0.12 - $0.09Conglomer 484 - 655 437 - 591 405 - 548 Conglomer $0.85 - $0.63 $1.26 - $0.93 $1.58 - $1.17Breccia 3,618 - 4,896 3,265 - 4,417 3,026 - 4,095 Breccia $0.11 - $0.08 $0.17 - $0.12 $0.21 - $0.16Limestone 3,044 - 4,119 2,747 - 3,716 2,546 - 3,445 Limestone $0.13 - $0.10 $0.20 - $0.15 $0.25 - $0.19Schist 5,664 - 7,663 5,110 - 6,913 4,737 - 6,409 Schist $0.07 - $0.05 $0.11 - $0.08 $0.14 - $0.10Slate 2,836 - 3,837 2,559 - 3,462 2,372 - 3,209 Slate $0.14 - $0.11 $0.21 - $0.16 $0.27 - $0.20Gneiss 1,219 - 1,650 1,100 - 1,489 1,020 - 1,380 Gneiss $0.34 - $0.25 $0.50 - $0.37 $0.63 - $0.46













EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-9

DRILL MODEL - Atlas Copco DM30 -DTH


5.50 6.00 6.50 5.50 6.00 6.50Granite 1,946 - 2,633 1,898 - 2,568 1,855 - 2,509 Granite $0.30 - $0.22 $0.33 - $0.25 $0.35 - $0.26Basalt 871 - 1,179 850 - 1,150 830 - 1,124 Basalt $0.66 - $0.49 $0.74 - $0.55 $0.77 - $0.57Gabbro 1,296 - 1,753 1,263 - 1,709 1,235 - 1,670 Gabbro $0.44 - $0.33 $0.50 - $0.37 $0.52 - $0.38Shale 1,845 - 2,496 1,799 - 2,434 1,758 - 2,378 Shale $0.31 - $0.23 $0.35 - $0.26 $0.36 - $0.27Sandstone 677 - 916 660 - 893 645 - 873 Sandstone $0.85 - $0.63 $0.95 - $0.71 $0.99 - $0.73Siltstone 4,884 - 6,608 4,763 - 6,444 4,654 - 6,297 Siltstone $0.12 - $0.09 $0.13 - $0.10 $0.14 - $0.10Conglomer 377 - 510 368 - 498 360 - 486 Conglomer $1.52 - $1.13 $1.71 - $1.27 $1.78 - $1.32Breccia 2,819 - 3,814 2,749 - 3,720 2,687 - 3,635 Breccia $0.20 - $0.15 $0.23 - $0.17 $0.24 - $0.18Limestone 2,372 - 3,209 2,313 - 3,130 2,260 - 3,058 Limestone $0.24 - $0.18 $0.27 - $0.20 $0.28 - $0.21Schist 4,413 - 5,970 4,303 - 5,822 4,205 - 5,689 Schist $0.13 - $0.10 $0.15 - $0.11 $0.15 - $0.11Slate 2,210 - 2,990 2,155 - 2,916 2,106 - 2,849 Slate $0.26 - $0.19 $0.29 - $0.22 $0.30 - $0.22Gneiss 950 - 1,285 927 - 1,254 905 - 1,225 Gneiss $0.61 - $0.45 $0.68 - $0.50 $0.71 - $0.52













EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-10

DRILL MODEL - Atlas Copco DM45 -DTH


5.00 6.50 8.00 5.00 6.50 8.00Granite 2,580 - 3,490 2,392 - 3,236 2,253 - 3,048 Granite $0.21 - $0.16 $0.27 - $0.20 $0.55 - $0.40Basalt 1,155 - 1,563 1,071 - 1,449 1,009 - 1,364 Basalt $0.48 - $0.35 $0.60 - $0.44 $1.22 - $0.90Gabbro 1,717 - 2,323 1,592 - 2,154 1,499 - 2,029 Gabbro $0.32 - $0.24 $0.40 - $0.30 $0.82 - $0.61Shale 2,445 - 3,308 2,267 - 3,067 2,135 - 2,888 Shale $0.22 - $0.17 $0.28 - $0.21 $0.58 - $0.43Sandstone 897 - 1,214 832 - 1,126 784 - 1,060 Sandstone $0.61 - $0.45 $0.77 - $0.57 $1.57 - $1.16Siltstone 6,473 - 8,758 6,001 - 8,120 5,652 - 7,647 Siltstone $0.08 - $0.06 $0.11 - $0.08 $0.22 - $0.16Conglomer 500 - 677 464 - 627 437 - 591 Conglomer $1.10 - $0.81 $1.38 - $1.02 $2.82 - $2.08Breccia 3,737 - 5,056 3,464 - 4,687 3,263 - 4,414 Breccia $0.15 - $0.11 $0.18 - $0.14 $0.38 - $0.28Limestone 3,144 - 4,254 2,915 - 3,944 2,745 - 3,714 Limestone $0.17 - $0.13 $0.22 - $0.16 $0.45 - $0.33Schist 5,849 - 7,913 5,422 - 7,336 5,107 - 6,910 Schist $0.09 - $0.07 $0.12 - $0.09 $0.24 - $0.18Slate 2,929 - 3,963 2,715 - 3,674 2,557 - 3,460 Slate $0.19 - $0.14 $0.24 - $0.17 $0.48 - $0.36Gneiss 1,259 - 1,704 1,168 - 1,580 1,100 - 1,488 Gneiss $0.44 - $0.32 $0.55 - $0.41 $1.12 - $0.83













EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-11

DRILL MODEL - Atlas Copco DM M2 -DTH


8.88 10.00 11.875 8.88 10.00 11.875Granite 1,779 - 2,407 1,719 - 2,325 1,636 - 2,213 Granite $0.78 - $0.58 $1.11 - $0.82 $2.75 - $2.03Basalt 796 - 1,078 770 - 1,041 732 - 991 Basalt $1.74 - $1.29 $2.47 - $1.82 $6.15 - $4.54Gabbro 1,184 - 1,602 1,144 - 1,548 1,089 - 1,473 Gabbro $1.17 - $0.86 $1.66 - $1.23 $4.13 - $3.06Shale 1,686 - 2,281 1,629 - 2,204 1,550 - 2,097 Shale $0.82 - $0.61 $1.17 - $0.86 $2.90 - $2.15Sandstone 619 - 837 598 - 809 569 - 770 Sandstone $2.24 - $1.65 $3.18 - $2.35 $7.91 - $5.85Siltstone 4,464 - 6,039 4,313 - 5,835 4,104 - 5,553 Siltstone $0.31 - $0.23 $0.44 - $0.33 $1.10 - $0.81Conglomer 345 - 467 333 - 451 317 - 429 Conglomer $4.02 - $2.97 $5.70 - $4.22 $14.19 - $10.49Breccia 2,577 - 3,486 2,490 - 3,368 2,369 - 3,205 Breccia $0.54 - $0.40 $0.76 - $0.56 $1.90 - $1.40Limestone 2,168 - 2,933 2,095 - 2,834 1,993 - 2,697 Limestone $0.64 - $0.47 $0.91 - $0.67 $2.26 - $1.67Schist 4,033 - 5,457 3,897 - 5,272 3,708 - 5,017 Schist $0.34 - $0.25 $0.49 - $0.36 $1.21 - $0.90Slate 2,020 - 2,733 1,951 - 2,640 1,857 - 2,512 Slate $0.69 - $0.51 $0.97 - $0.72 $2.42 - $1.79Gneiss 868 - 1,175 839 - 1,135 798 - 1,080 Gneiss $1.59 - $1.18 $2.26 - $1.67 $5.64 - $4.17













EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-12

DRILL MODEL - Atlas Copco DM25SP - Rotary















EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-13

DRILL MODEL - Atlas Copco DM30 -Rotary















EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-14

DRILL MODEL - Atlas Copco DM45 -Rotary















EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-15

DRILL MODEL - Atlas Copco DM M2 -Rotary















EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-16

DRILL MODEL - Bucyrus International 59R -Rotary


12.25 15.00 16.00 12.25 15.00 16.00Granite 3379.984 - 4572.919 3213.372 - 4347.504 3162.023 - 4278.031 Granite $1.95 - $1.44 $3.23 - $2.38 $3.48 - $2.58Basalt 1770.653 - 2395.589 1683.371 - 2277.502 1656.471 - 2241.108 Basalt $3.73 - $2.76 $6.16 - $4.55 $6.65 - $4.92Gabbro 1996.573 - 2701.246 1898.155 - 2568.092 1867.823 - 2527.054 Gabbro $3.31 - $2.44 $5.46 - $4.04 $5.90 - $4.36Shale 3546.993 - 4798.873 3372.149 - 4562.319 3318.263 - 4489.414 Shale $1.86 - $1.38 $3.07 - $2.27 $3.32 - $2.45Sandstone 3697.769 - 5002.863 3515.492 - 4756.254 3459.315 - 4680.25 Sandstone $1.79 - $1.32 $2.95 - $2.18 $3.18 - $2.35Siltstone 3681.304 - 4980.588 3499.839 - 4735.076 3443.912 - 4659.411 Siltstone $1.79 - $1.33 $2.96 - $2.19 $3.20 - $2.36Conglomer 4247.818 - 5747.048 4038.427 - 5463.755 3973.894 - 5376.445 Conglomer $1.55 - $1.15 $2.57 - $1.90 $2.77 - $2.05Breccia 5863.339 - 7932.753 5574.314 - 7541.719 5485.238 - 7421.204 Breccia $1.13 - $0.83 $1.86 - $1.37 $2.01 - $1.48Limestone 4870.335 - 6589.277 4630.259 - 6264.468 4556.268 - 6164.363 Limestone $1.36 - $1.00 $2.24 - $1.65 $2.42 - $1.79Schist 5972.24 - 8080.09 5677.846 - 7681.792 5587.116 - 7559.039 Schist $1.11 - $0.82 $1.83 - $1.35 $1.97 - $1.46Slate 3888.976 - 5261.555 3697.274 - 5002.194 3638.192 - 4922.26 Slate $1.70 - $1.25 $2.80 - $2.07 $3.03 - $2.24Gneiss 3539.394 - 4788.591 3364.924 - 4552.544 3311.153 - 4479.796 Gneiss $1.87 - $1.38 $3.08 - $2.28 $3.33 - $2.46


12.25 15.00 16.00 12.25 15.00 16.00Granite 41969.55 - 56782.33 39900.72 - 53983.32 39263.11 - 53120.68 Granite $0.078 - $0.058 $0.082 - $0.061 $0.083 - $0.062Basalt 24574.25 - 33247.51 23362.89 - 31608.62 22989.56 - 31103.52 Basalt $0.133 - $0.098 $0.140 - $0.104 $0.142 - $0.105Gabbro 27142.87 - 36722.71 25804.9 - 34912.52 25392.55 - 34354.62 Gabbro $0.121 - $0.089 $0.127 - $0.094 $0.129 - $0.095Shale 43679.22 - 59095.42 41526.11 - 56182.39 40862.54 - 55284.61 Shale $0.075 - $0.055 $0.079 - $0.058 $0.080 - $0.059Sandstone 45210.83 - 61167.6 42982.23 - 58152.42 42295.38 - 57223.16 Sandstone $0.072 - $0.054 $0.076 - $0.056 $0.077 - $0.057Siltstone 45044.11 - 60942.03 42823.72 - 57937.98 42139.41 - 57012.14 Siltstone $0.073 - $0.054 $0.076 - $0.056 $0.078 - $0.057Conglomer 50711.07 - 68609.09 48211.33 - 65227.1 47440.93 - 64184.78 Conglomer $0.065 - $0.048 $0.068 - $0.050 $0.069 - $0.051Breccia 66219.99 - 89591.75 62955.76 - 85175.45 61949.75 - 83814.36 Breccia $0.049 - $0.037 $0.052 - $0.038 $0.053 - $0.039Limestone 56790.17 - 76833.76 53990.78 - 73046.35 53128.02 - 71879.08 Limestone $0.058 - $0.043 $0.061 - $0.045 $0.062 - $0.046Schist 67236.6 - 90967.16 63922.26 - 86483.06 62900.8 - 85101.08 Schist $0.049 - $0.036 $0.051 - $0.038 $0.052 - $0.038Slate 47137.81 - 63774.69 44814.22 - 60631 44098.1 - 59662.13 Slate $0.069 - $0.051 $0.073 - $0.054 $0.074 - $0.055Gneiss 43601.73 - 58990.58 41452.44 - 56082.72 40790.04 - 55186.53 Gneiss $0.075 - $0.055 $0.079 - $0.058 $0.080 - $0.059



12.25 15.00 16.00 Number of rods Factor the total steel cost per foot of hole drilled dependsGranite 19.00236 - 25.70907 12.60139 - 17.04894 11.05531 - 14.95719 upon the total number of 12 foot sections in the hole.Basalt 11.03265 - 14.92652 7.316286 - 9.898504 6.418644 - 8.684048 1 1.0 Divide the total hole length by 12 and round this resultGabbro 12.205 - 16.51264 8.093728 - 10.95034 7.100701 - 9.606831 2 1.5 up to the next whole number to determine number of Shale 19.78892 - 26.77325 13.123 - 17.75464 11.51293 - 15.57631 3 2.0 rods required to drill the hole. Adjust this number to theSandstone 20.49398 - 27.72715 13.59055 - 18.38722 11.92312 - 16.13128 4 2.5 average number of rods during drilling by consultingSiltstone 20.41721 - 27.62329 13.53965 - 18.31835 11.87846 - 16.07085 5 3.0 the Drill Steel Cost Adjustment Factor table to the left.Conglomer 23.02897 - 31.15684 15.27163 - 20.66162 13.39794 - 18.12663 6 3.5 Multiply this adjustment factor times the cost per footBreccia 30.19898 - 40.85745 20.02642 - 27.09456 17.56936 - 23.77031 7 4.0 per rod from the table above. The result is the totalLimestone 25.83581 - 34.95433 17.13298 - 23.17992 15.03092 - 20.33595 8 4.5 drill steel cost per foot of hole drilled. Other drillSchist 30.66998 - 41.49468 20.33876 - 27.51714 17.84338 - 24.14104 9 5.0 steel lengths may be adjusted for by determining theSlate 21.38157 - 28.92801 14.17916 - 19.18357 12.43951 - 16.82992 10 5.5 total length of rods required and then converting that Gneiss 19.75326 - 26.725 13.09935 - 17.72265 11.49218 - 15.54824 n (n+1)/2 to the number of equivalent 12 foot sections. Once








EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-17

DRILL MODEL - Atlas Copco TBH4 - Rotary















EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-18

Drill Bits Drill Rod

Bit Type Bit Size Bit Price Rod Type Rod Size Rod Price Button - drop center Percussion rod - 12 ft

1-3/4" $62 R32 $2802" $69 T38 $3242-1.2" $98 T45 $4073" $131 T51 $5683-1.2" $1594" $223 DTH rod - 9'10"4-1.2" $268 3.0 76mm $3845" $321 3.5 89mm $431

4.0 102mm $491 DTH - concave face 4.5 114mm $592

3-1/2" $410 5.5 140mm $8155" $5505-1/2" $575 Rotary rod - 25' to 30'6" $630 4" x 25' $3,3006-1/2" $640 5" x 25' $3,9008" $1,230 7" x 30' $6,9008-7/8" $1,385 8-5/8" x 30' $6,80010" $1,900 10-3/4" x 27.5 $7,50011-/7/8 $4,500

TRICONE - carbide insert3-7/8" $1,1505" $1,6295-1/2" $1,972 All unit prices are manufacturer6" $2,131 list prices. Discounts or 6-1/4" $2,207 premiums may apply depending6-3/4" $2,463 upon market conditions.7-7/8" $3,0239" $3,5899-7/8" $4,78711" $5,64012-1/4" $6,60315" $10,36716" $11,016

BIT AND DRILL STEEL PRICE DATABASE Effective date - 8/2006


EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-19

ROTARY BLASTHOLE DRILLS

Bucyrus manufactures electric rotary blasthole drills with the most innovative features on the market, including programmed drill control, rack and pinion pull-down, hydrostatic propel drives and more. Contact us today for more information about any of our performance-packed drills!

59R Max. hole size: 444 mm (17-1/2 in) Max. bit loading: 74,830 kg (165,000 lbs) Working weight: 183,673 kg (405,000 lbs)

49RIII Max. hole size: 406 mm (16 in) Max. bit loading: 63,975 kg (141,000 lbs) Working weight: 154,224 kg (340,000 lbs)

39HR Max. hole size: 349 mm (13-3/4 in) Max. bit loading: 55,000 kg (122,000 lbs) Working weight: 122,500 kg (270,000 lbs)

35HR Series Max. hole size: 270 mm (10-5/8 in) Max. bit loading: 34,000 kg (75,000 lbs) Working weight: 54,432 kg (120,000 lbs)

EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-20

Drilling Solutions

Ingersoll-Rand has been in the drilling business since Simon Ingersoll invented his first rock drill in 1871. This innovative piece of machinery revolutionized the drilling industry and set the pace for the company's future.

Ingersoll-Rand drills are designed and manufactured to a stringent set of quality standards, assuring you of the most efficient and reliable drills available anywhere.

Now in our second century, we are proud of the comprehensive line of Ingersoll-Rand drilling equipment for the mining, exploration, oil and gas, quarry and water well industries around the world.

Drilling Solutions Blasthole Drills Rotary Large Mid-range Hydraulic Crawle Pneumatic Crawl DHD Drill Selector Waterwell Drills Exploration Drills Gas & Oil / Coal BedDrills

Drilling Accessories Down Hole Drills Threaded Access Hollow Anchor Syst Literature Split Set Products Aftermarket Upgrades Kits Product Upgrad Maintenance Up Promotions Maintenance Sche Service New Product Events Calendar Authorized Distribut Used Equipment Federal Governmen Contact Us Training Schedule

Copyright © 1996-2001 Ingersoll-Rand Company. All rights reserved. Ingersoll-Rand Worldwide Headquarters 200 Chestnut Ridge Road Woodcliff Lake, NJ 07675 USA

HOME BACK

EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-21

EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-22

Select Model:

T4BHDM25/SP

DM30DM45/LPDM50/LPDM-L/LPDM45/SPDM-LSPDM-M2DM-M3DM-H2

351

Rotary - DM45/LP

The DM45/LP is a hydraulic rotary head drive, multi-pass, crawler-mounted drill rig with a 45,000 lb. (20,400 kg) bit load capacity. The standard two-motor spur gear rotary head is rated from 9,000 ft-lb. (12,204 N-m) at 0-100 RPM and 5,400 ft-lb. (732 N-m) at 0-160 RPM. The DM45/LP can drill from 5-1/8 to 7-7/8 in. (130 to 200 mm) diameter blastholes to depths of 180 ft. (55 m) with a 30 ft. (9.1 m) drill pipe change. Two low-pressure Ingersoll-Rand compressor options are available with your choice of Caterpillar or Cummins engines.

[ SPECS ] [ FEATURES ] [ LITERATURE ]

Nominal Hole DiameterDiameter 6-8 in.

Power PackEngine #1 Cummins QSX15 (425 HP @ 1800 rpm)

Compressor #1 900 @ 110 CFM @ PSI / 25.5 @ 758 m3/min@kPA

Engine #2 CAT C15 (425 HP @ 1800 RPM)


Engine #3 Cummins QSX15 (475 HP @ 1800 RPM)


Engine #4 Cat C15 (475 HP @ 1800 RPM)


Rotation

Type 2-motor variable displacement, high torque/high speed

Head Torque High torque: 9,000 ft-lb @ 100 rpm Speed High speed: 5,400 ft-lb @ 160 rpm rpm

Feed System

Type Hydraulic cyls. w/cable pulldown & chain pullback

Bit Load 45,000 lb / 20,411 kg Tower

Pipe Length 30 ft. / 9.1 m.

Fabrication 4-member open front w/rectangular hollow steel tubing/double cut lacing

UndercarriageModel Caterpillar 325L or equivalent



EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-23

Length 15.3 ft. / 4.66 m Carousel

Capacity Capable of 180 ft. Options

Option #1 Contact your local IR distributor for a complete list of options.

Weight & DimensionsHeight (Tower Up) 43 ft. / 13.11 m

Approx. Working Weight 77,000 - 85,000 lbs. / 34,900 - 38,600 kg. Material To Be Drilled

Soft Yes Drill Application

Mining Yes Quarry Yes

Drilling MethodRotary Yes


HOME BACK

EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-24

Select Model:

T4BHDM25/SP


351

Rotary - DM30

The DM30 is a hydraulic tophead drive, multi-pass, crawler-mounted drill rig designed for blastholes ranging from 5-1/8 to 6-3/4 in. (130 to 171 mm) in diameter. On-board depth capability is up to 150 ft. (45.7 m). For rotary drilling, the DM30 can assert a bit load force up to 30,000 lb. (13,608 kg) and rotation speeds of 0-130 RPM. This rig can also be used with downhole drills when equipped with a high-pressure air compressor option.



Power PackEngine #1 Cummins QSX15 (525 HP @ 1800 RPM)

Compressor #1 IR HR2 900/350 CFM @ PSI / 25.5/2,413 m3/min@kPA




Compressor #3 IR WW226 900/110 CFM @ PSI / 25.5/758 m3/min@kPA



Floating Sub Base Isolates components from drilling and propel shock loads/maintains alignment

RotationType Rotary Tophead

Head Torque 5,400 ft-lb. / 7,322 N-m Speed 0-100 rpm

Feed SystemType Single cylinder, cable feed

Bit Load 30,000 lb / (13,608) kg Tower


Construction 4 member open front with hollow steel tubing.



EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-25

UndercarriageManufacturer Caterpillar

Options


Weight & DimensionsHeight (Tower Up) 44.3 ft. / 13.4 m

Approx. Working Weight 68,000 lbs. / 30,844 kg. Material To Be Drilled

Hard Yes Medium Yes



Drilling MethodRotary Yes DHD Yes


HOME BACK

EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-26

Select Model:

T4BHDM25/SP


351

Rotary - DM25/SP

The DM25SP is a crawler-mounted rotary table drill rig designed for single-pass blasthole drilling to depths of up to 50 ft. (15.2 m) and diameters of 3-1/2 to 6-3/4 in. (89 to 171 mm). This drill is capable of rotary drilling with 25,000 lb. (11,340 kg) of bit load at 0-200 rpm. The DM25SP can also be used with downhole drills when equipped with a high-pressure air compressor option.




Compressor #1 900/350 CFM @ PSI / 25.5/2,413 m3/min@kPA




Compressor #3 900/110 CFM @ PSI / 25.5/758 m3/min@kPA



RotationType Rotary Table Drive

Speed 0-170 rpm Torque 3,500 / (4,746 N-m)

Feed SystemType Heavy-duty chains through cluster sprocket

Pulldown 25,000 lbs. / 11,340 kg. Tower

Construction 4 main member, open front, rectangular steel tubing

#1 Single pass depth 40 ft. / 12.2 m. #2 Single pass depth 50 ft. / 15.2 m.

Undercarriage



EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-27

Type Excavator Options


Weight & Dimensions

Weight Varies according to drill pipe: 60,000 - 62,000 lb / 27,216-28,123 kg

Material To Be DrilledHard Yes

Medium Yes Soft Yes

Drill ApplicationQuarry Yes



HOME BACK

EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-28

Select Model:

T4BHDM25/SP


351

Rotary - DM-M2

Designed for rotary or downhole drilling of up to 10-5/8 in. (270 mm) diameter blastholes, the DM-M2 provides 75,000 lb. (34,000 kg) of bit load and a 35 ft. (10 m) drill pipe change. Advanced frame and tower design and a unique, patented carriage feed system allow on-board drill depths to 175 ft. (53 m). Compressor/engine packages in both low-pressure, [1900 CFM @ 110 PSI (51 m3/min. @ 758 kPa)] for rotary drilling and high pressure [1250 CFM @ 350 PSI (35.4 m3/min. @ 2,413 kPa)], for downhole drilling, are available.



Power PackEngine #1 Caterpillar 3412E / EPA certified


Engine #2 Cummins QSK19 / EPA certified


Engine #3 Caterpillar 3412E / EPA certified


RotationType Two-motor, variable displacement

Speed Range 0-150 rpm, variable Head Torque 0-8,640 ft-lbs (0-11,714 Nm) (forward)

Feed SystemType Patented carriage feed

Weight on Bit 0 to 75,000 lb. / 0 to 34,019 kg Tower



UndercarriageModel Caterpillar 330EL or equivalent

Carousel

Size Holds 2 to 4 drill pipe depending on pipe diameter



EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-29

Options




Medium Yes Soft Yes

Drill ApplicationMining Yes



HOME BACK

EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-30

Select Model:

T4BHDM25/SP


351

Rotary - T4BH

The T4BH is a truck-mounted, hydraulic tophead drive multipass rotary drill specificaly designed for production blasthole drilling to depths of 150 ft. (45.7 m) with a 25 ft. (7.6 m) drill pipe change. Nominal hole size is 5-1/8 to 7-7/8 in. (130 to 200 mm) for rotary or DHD drilling methods. Feed pressure generates a bit load force of up to 30,000 lb. (12,610 kg). An angle drilling option is available. All drill functions are controlled from the newly designed operator cab.



CarrierChassis (Standard) Crane Carrier, Custom, 3 axle, 6X4

Engine CAT C10 (305 HP) Power Pack


Compressor #1 IR HR2-900/350 CFM @ PSI / 25.5/2413 m3/min@kPA



Engine #3 Cummins QSK-19C (700 HP @ 2100 RPM)

Compressor #3 IR HR2.5 - 1250/350 CFM @ PSI / (35.39 @ 2413) m3/min@kPA



Speed Range 0-160 RPM (std.) Head Torque 6,500 ft-lb. / (8,814 N-m)

Option 7,165 ft-lb @ 0-130 RPM / 9,716 N-m @ 0-130 RPM

Feed SystemType Hydraulic cylinders w/cable and chain

Pulldown 0-37,700 lbs. / 17,108 kg.



EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-31

TowerPipe Length 25 ft. / 7.6 m.

Construction 4 member open front with ASTM A500 GRB steel tubing.

Cab & Controls

Operator Cab New cab designed to optimize operator comfort and safety

Controls All operational functions controlled from driller console in cab

Options

Option #1 Contact your local distributor for a complete list of options.

Weight & DimensionsHeight (Tower Up) 28-3/4 ft. / 8.7 m


Hard Yes Medium Yes



Drilling MethodRotary Yes


HOME BACK

EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-32

Select Model:

CM695DDM25/SP

DM30DM45/HPDM45/SPDM-L/HPDM-M2

DHD - DM-M2

Designed for rotary or downhole drilling of up to 10-5/8 in. (270 mm) diameter blastholes, the DM-M2 provides 75,000 lb. (34,000 kg) of bit load and a 35 ft. (10 m) drill pipe change. Advanced frame and tower design and a unique, patented carriage feed system allow on-board drill depths to 175 ft. (53 m). Compressor/engine packages in both low-pressure, [1900 CFM @ 110 PSI (51 m3/min. @ 758 kPa)] for rotary drilling and high pressure [1250 CFM @ 350 PSI (35.4 m3/min. @ 2,413 kPa)], for downhole drilling, are available.



Power PackEngine #1 Caterpillar 3412E / EPA certified


Engine #2 Cummins QSK19 / EPA certified


Engine #3 Caterpillar 3412E / EPA certified


RotationType Two-motor, variable displacement

Speed Range 0-150 rpm, variable Head Torque 0-8,640 ft-lbs (0-11,714 Nm) (forward)

Feed SystemType Patented carriage feed

Weight on Bit 0 to 75,000 lb. / 0 to 34,019 kg Tower



UndercarriageModel Caterpillar 330EL or equivalent

Carousel

Size Holds 2 to 4 drill pipe depending on pipe diameter



EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-33

Options




Medium Yes Soft Yes




HOME BACK

EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-34

Select Model:

CM695DDM25/SP


DHD - DM30

The DM30 is a hydraulic tophead drive, multi-pass, crawler-mounted drill rig designed for blastholes ranging from 5-1/8 to 6-3/4 in. (130 to 171 mm) in diameter. On-board depth capability is up to 150 ft. (45.7 m). For rotary drilling, the DM30 can assert a bit load force up to 30,000 lb. (13,608 kg) and rotation speeds of 0-130 RPM. This rig can also be used with downhole drills when equipped with a high-pressure air compressor option.













Head Torque 5,400 ft-lb. / 7,322 N-m Speed 0-100 rpm

Feed SystemType Single cylinder, cable feed

Bit Load 30,000 lb / (13,608) kg Tower





EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-35

UndercarriageManufacturer Caterpillar

Options




Hard Yes Medium Yes





HOME BACK

EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-36

Select Model:

CM695DDM25/SP


DHD - DM25/SP

The DM25SP is a crawler-mounted rotary table drill rig designed for single-pass blasthole drilling to depths of up to 50 ft. (15.2 m) and diameters of 3-1/2 to 6-3/4 in. (89 to 171 mm). This drill is capable of rotary drilling with 25,000 lb. (11,340 kg) of bit load at 0-200 rpm. The DM25SP can also be used with downhole drills when equipped with a high-pressure air compressor option.











RotationType Rotary Table Drive

Speed 0-170 rpm Torque 3,500 / (4,746 N-m)

Feed SystemType Heavy-duty chains through cluster sprocket


Construction 4 main member, open front, rectangular steel tubing

#1 Single pass depth 40 ft. / 12.2 m. #2 Single pass depth 50 ft. / 15.2 m.

Undercarriage



EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-37

Type Excavator Options


Weight & Dimensions

Weight Varies according to drill pipe: 60,000 - 62,000 lb / 27,216-28,123 kg


Medium Yes Soft Yes

Drill ApplicationQuarry Yes



HOME BACK

EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-38

Select Model:

CM695DDM25/SP


DHD - DM45/SP

The DM45/SP is a crawler-mounted hydraulic rotary table drive, drill rig designed to produce 50 ft. (15.2 m) of clean hole in a single pass. Hole diameter capability is 5-1/2 to 6-3/4 in. (139.7 to 171.5 mm) to a depth of up to 50 ft. (15.2 m) with a downhole hammer (high-pressure air package). Feed pressure generates a bit load force of up to 25,000 lb. (11,340 kg). An optional angle drilling system is available.











RotationType Rotary table w/kelly drive

Speed 0-200 rpm Torque 4,000 ft-lb / (5,424 N-m)

Feed SystemType Chain and cable


Type Single Pass Pipe Length 50 ft. / 15.2 m.

4 member open front with rectangular steel



EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-39

Construction tubing Undercarriage

Type Excavator-type Options


Weight & DimensionsHeight (Tower Up) 76-1/2 ft. / 23.3 m


Hard Yes Medium Yes

Drill ApplicationMining Yes Quarry Yes

Drilling MethodDHD Yes


HOME BACK

EP OctpbEP 1110-1-8, Vol. 130 Nov 09

L-40

Select Model:

LM100ACM348

ECM350

Pneumatic Crawler - ECM350

This agile, powerfull drill climbs steep grades over roughest ground, and takes the punishment. You have seen thousands of them on construction jobs of all kinds around the world. The basic ECM350 design has seen many improvements in its years of service ? but every drill produced has set the world standard for reliability and perfomance in its time. The ECM350 is also a fine quarry drill when teamed with an Ingersoll-Rand air compressor. This high-performance team gets more work done faster, more efficiently, and keeps doing it longer than anything else in its class.


Nominal Hole DiameterDiameter 2-1/2 - 5-1/2 in.

DrifterDrifter #1 VL140

Hole Diameter #1 2.5-4 " / 64-102 mm Rotation Speed #1 0 - 72 rpm

Frequency #1 2100 BPM

Air Consumption #1 750 SCFM @ 100 PSI / 21.2 m3/min @ 7 kg/cm2

Stroke #1 5-1/2 in. / 140 mm. Bore #1 5-1/2 in. / 140 mm.

Weight #1 421 lb. / 191 kg. Guide

Guide Dump #1 180 °Guide Swing (L/R) 50 deg / 35 deg

BoomBoom Swing (L/R) #1 40 ° / 35 °

Boom Lift (Up/Down) #1 45 ° / 15 ° Air Rotary Head

Weight 554 lb. / 252 kg.

Torque Max. 1492 Nm @ 8.4 kg/cm? / (1100 lb-ft @ 120 PSI)

Rotation 0 - 72

Air Consumption 120 CFM @ 50 RPM & 90 PSI / 3.4 m3/min @ 50 RPM & 6.3 kg/cm2

Gear Ratio 33:1

Horse Power 2.23 kw @ 6.3 kg/cm? (3.0 hp @ 90 psig) / 3.13 kw @ 8.4 kg/cm? (4.2 hp @ 120 psig)

GeneralFeed/Pullback Force 3,000 lb / 1,361 kg



EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-41

Downhole DrillsO.D. #1 3.62 in. / 92 mm.

Length (bit ext.) #1 45.7 in. / 1161 mm. Air Consumption @ 10.5 kg/cm? (150

PSIG) #1 5.1 m?/min / (180 SCFM)

Air Consumption @ 17.6 kg/cm? (250 PSIG) #1 9.9 m?/min / (350 SCFM)

Drill #2 DHD350R Hole Diameter #2 5-1/8 - 5-1/2 in. / 130-140 mm.

Weight (less bit) #2 151 lb. / 68.5 kg. O.D. #2 4.5 in. / 114 mm.

Length (bit ext.) #2 54.6 in. / 1388 mm. Air Consumption @ 10.5 kg/cm? (150

PSIG) #2 7.9 m?/min / (280 SCFM)

Air Consumption @ 17.6 kg/cm? (250 PSIG) #2 14.7 m?/min / (520 SCFM)

Crawlair Drill SpecificationsNet weight 12,900 lb. / 5851 kg.

Overall shipping length 12 ft. 0 in. / 3645 mm. Width 8 ft 0 in. / 2438 mm.

Height (vertical guide) 18 ft. 10 in. / 5753 mm. Steel change 12 ft. / 3645 mm.

Drill travel 14 ft. 3 in. / 4356 mm. Max. horizontal boom swing 40? left, 35? right

Max. vertical boom movement 45? above, 15? below Max. guide swing 50? left, 35? right Max guide dump 180?

Ground clearance 12 in. / 292 mm. Grouser width 10 in. / 254 mm.

Weight & DimensionsGround Clearance 12 " / 292 mm

Shipping Width 96 " / 2438 mm Shipping Length 144 " / 3645 mm

Approx. Working Weight 12,900 lbs. / 5851 kg. Material To Be Drilled

Hard Yes Medium Yes


Mining Yes Construction Yes

Quarry Yes Drilling Method

Drifter Yes


HOME BACK


L-42

Select Model:

ECM470ECM580ECM590

ECM660IIECM-720

Hydraulic Crawler - ECM-720

They said it couldn't be done...they were wrong. The new ECM-720 crawler drill delivers a perfect balance of productivity and cost efficiency. Hole straightness, faster penetration rates, long accessory life, and increased profitability are just a few of the results you can expect with the ECM-720.



DrifterType Montabert HC-200A

Boom & GuideBoom Swing 45 deg right / 20 deg left maximum

Vertical Boom Movement 50 deg up / 20 deg down maximum Guide Swing 20 deg right / 90 deg left maximum Guide Dump 135 deg maximum

Boom Extension 36 in. / 914 mm Guide Extension 5 ft / 1,524 mm

Overall Guide Length 27 ft 6 in / 8.4 m Drifter Travel 16 ft. 11 in. / 5.15 m

EngineType CAT 3176 C-10

Rated Power 365 HP / 272 kW Operating Speed 1,800 rpm

CompressorType Ingersoll-Rand Rotary Screw

Volume 480 CFM / 13.6 m3/min Pressure 150 PSI / 10.3 BAR

Cab & ControlsOperator Cab ROPS/FOPS

Noise level 80 dBA General

Gradeability 35 deg (70 percent) °Tramming Speed 2.0 mph / 3.3 km/hr Ground clearance 17 in. / 432 mm.

Grouser Width 13-3/4 in. / 349 mm mm. Rod Changer Capacity (6) 12 ft (3.66 m) / (6) 14 ft (4.27 m) opt.

Shipping InformationWeight 45,900 lb / 20,820 kg



EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-43

Width 8 ft 3 in / 2.5 m Length 35 ft 8 in / 10.9 m Height 10 ft 8 in / 3.3 m


Medium Yes Soft Yes


Construction Yes Quarry Yes

Drilling MethodDrifter Yes


HOME BACK


L-44

Select Model:

ECM470ECM580ECM590

ECM660IIECM-720

Hydraulic Crawler - ECM590

The ECM-590 is a self-contained, cabless hydraulic crawler drill capable of drilling up to 4 in. (102 mm) holes. It is available in either a YH70 drifter and rod rack configuration for smaller hole work, or with a YH80 and rod changer for higher production requirements. An extended guide option for 20 ft. (6.1 m) starter steel is available.



DrifterDrifter #1 YH70

Hole Diameter #1 2.5-4 " / 64-102 mm Rotation Speed #1 0-200 rpm

Frequency #1 2800 BPM Weight #1 419 lb. / 190 kg.

Steel Size #1 T45/T38 Drifter #2 YH80A

Hole Diameter #2 2.5-4.5 in. / 64-114 mm. Rotation Speed #2 0-200 rpm

Frequency #2 2600 BPM Weight #2 462 lb. / 210 kg.

Steel Size #2 T51/T45 Hydraulic Pressure 2130 psi / 150 kg/cm?

Boom & GuideHorizontal Boom Swing 30 deg R / 34.6 deg L

Vertical Boom Movement 51 deg up / 15 deg down Guide Swing 48 deg R / 40 deg L Guide Dump 180 deg

Boom Extension - YH70 (YH80A) 48 in (30 in) / 1,219 mm (762 mm) Drifter Travel - YH70 (YH80A) 15 ft 4 in (14 ft) / 3,099 mm (4,267 mm)

Guide Extension 4 ft / 1,219 mm Overall Guide Length 23 ft 8 in / 7,214 mm

EngineType Cummins 6CT8.3

Rated Power 215 HP / 159 kW Operating Speed 2350 rpm



EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-45

IR Rotary Screw CompressorCompressor pressure(max) 140 psig / 9.8 kg/cm2

Compressor volume 250 cfm / 7 m?/min General

Gradeability 35 °Tramming Speed 2 mph / 3.3 km/hr

Grouser Width 12 in. / 305 mm. Steel length starter rod 14 ft. / 4.27 m.

Weight & DimensionsLength 232.9 " / 5918 mm

Weight #2 24,500 lb. / 11,150 kg. Ground Clearance 18 " / 457 mm

Shipping Width 95.98 " / 2438 mm Shipping Height 112 " / 2845 mm


Medium Yes Soft Yes

Drill ApplicationConstruction Yes

Drilling MethodDrifter Yes


HOME BACK


L-46

Select Model:

LM100ACM348

ECM350

Pneumatic Crawler - LM100A

The LM100A is a small class pneumatic Crawlair?, capable of drilling 1-3/4" to 4- 1/2" (44 - 114 mm) diameter holes. It can be equipped with either of two drifters or a BRH rotary head for downhole drilling. The LM100A is ideal for applications in confined areas where hand-held tools are not enough, and is light enough to transport by helicopter. Like all Ingersoll-Rand crawler drills, the LM100A is "Abuse Resistant". It keeps coming back for more!



CarrierOverall Track Length 72 " / 1845 mm

Ground Clearance 9 " / 230 mm Oscillation 20 °Air Motors 4.5 HP

Gradeability 30 °Tramming Speed 0-2 mph / 0-3.2 km/hr

DrifterType Ingersoll-Rand YD90

Hole Diameter #1 1.75-2.5 " / 44-64 mm Frequency #1 1600 BPM

Air Consumption #1 375 scfm @ 100 psi & 50 rpm / 10.6 m3/min @ 7 kg/cm2 & 50 rpm

Stroke #1 3.4 in. / 85 mm. Bore #1 3.5 in. / 90 mm.

Steel Size #1 10 ft / 3048 mm Drifter #2 VL120

Hole Diameter #2 2 - 3.5 in. / 51 - 89 mm. Frequency #2 1900 BPM

Air Consumption #2 600 SCFM @ 50 RPM & 100 psi / 17.0 m3/min @ 50 RPM & 7 kg/cm2

Stroke #2 3.62 in. / 92 mm. Bore #2 4.75 in. / 120 mm.

Steel Size #2 10 ft / 3048 mm Guide

Guide Dump #1 75 °Guide Swing (L/R) 45 deg/45 deg



EP Octpb

EP 1110-1-8, Vol. 130 Nov 09

L-47

Guide Extension #1 29 " / 750 mm Drill Rod Length 10 ft. / 3 m Feed Motor Pull 3000 lbs. / 1360 kg.

BoomBoom Swing (L/R) #1 30/35 °

Boom Lift (Up/Down) #1 45/30 ° Coverage Length 107 " / 2720 mm

Max. Drill Height (Horizontal) 99 " / 2510 mm BRH Rotary Head

Weight 304 lbs. / 138 kg. Torque Maximum 700 lb.-ft. / 96.7 kg.-m Rotation Range 0 - 50 RPM

Air Consumption 120 SCFM @ 50 RPM & 100 psi / 3.39 m3/min @ 50 RPM & 7 kg/cm2

Gear Ratio 20:1 Horse Power @ 100 psi (7 kg/cm) 4.5 HP / 3.35 kW

Weight & DimensionsWidth 75 " / 1905 mm

Length (Boom @45°) 195 " / 4950 mm Minimum Height 44 " / 1120 mm

Height (Boom @45°) 188 " / 4775 mm Hole Size 1.75-4.5 " / 44-114 mm

Weight Less Drifter 5400 lbs. / 2450 kg. Material To Be Drilled

Hard Yes Medium Yes


Mining Yes Construction Yes

Quarry Yes Drilling Method

Drifter Yes


HOME BACK


L-48

Glossary-1

GLOSSARY

Terms and Abbreviations

EP 1110-1-8, Vol. 130 Nov 09

Glossary-2

AVF average value factor bhp brake horsepower CAT category CENWW U.S. Army Corps of Engineers, Walla Walla District CMR cost of money rate cwt hundredweight D diesel DC discount code DEPR depreciation DT drive tire E electricity EAF economic adjustment factor EK economic key EP Engineer Pamphlet ER Engineer Regulation FAR Federal Acquisition Regulation EFAR Engineer Federal Acquisition Regulation FCCM facilities capital cost of money FOG filters, oil, and grease FT front tire G gas G&A general and administrative gal gallon GCW gross combined weight GVW gross vehicle weight hp horsepower HPF horsepower factor hr hour ID No. identification number IGE Independent Government Estimate kW kilowatt LAF labor adjustment factor lbs pounds LIFE Chapter 1 economic life (probably should take this out) N number of years PDF portable document format PTO power take off RCF repair cost factor RF repair factor ROPS Rollover protective structures RPR repairs SLV salvage value

EP 1110-1-8, Vol. 130 Nov 09

Glossary-3

SUB subcategory TCI tire cost index TEV total equipment value TT trailing tire WHPY working hours per year wk week WLS water, lube, and supplies yr year

EP 1110-1-8, Vol. 130 Nov 09


Glossary-4

EP 1110-1-8, Vol. 130 Nov 09

Index-1

EQUIPMENT INDEX CAT DESCRIPTION PAGE A10 AGGREGATE / CHIP SPREADERS................................................................... 2-22

A15 AIR COMPRESSORS, PORTABLE.................................................................... 2-23

A20 AIR HOSE, TOOLS & EQUIPMENT .................................................................. 2-27

A25 ASPHALT PAVING DISTRIBUTORS ................................................................. 2-30

A30 ASPHALT PAVERS & MISCELLANEOUS ROAD EQUIPMENT........................ 2-31

A35 ASPHALT PAVING KETTLES ......... .................................................................. 2-36

A40 ASPHALT & CONCRETE MILLERS / PROFILERS / PLANERS /

ROTARY GRINDERS ....................................................................................... 2-37

A45 ASPHALT RECYCLERS & SEALERS ............................................................... 2-38

B10 BATCH PLANTS, ASPHALT & CONCRETE ..................................................... 2-39

B15 BROOMS, STREET SWEEPERS & FLUSHERS .............................................. 2-47

B20 BRUSH CHIPPERS ............................................................................................ 2-49

B25 BUCKETS, CLAMSHELL.................................................................................... 2-50

B30 BUCKETS, CONCRETE .................. .................................................................. 2-52

B35 BUCKETS, DRAGLINE ...................................................................................... 2-55

C05 CHAIN SAWS .................................. .................................................................. 2-61

C10 COMPACTORS, WALK-BEHIND OR REMOTE CONTROLLER ....................... 2-62

C15 CONCRETE CLEANERS / ABRASIVE BLASTERS........................................... 2-65

C20 CONCRETE BUGGIES ...................................................................................... 2-66

C25 CONCRETE FINISHERS/SCREEDS/SPREADERS .......................................... 2-66

C35 CONCRETE GUNITERS / SHOTCRETERS ..................................................... 2-69

C40 CONCRETE MIXING UNITS .............................................................................. 2-71

C45 CONCRETE PAVING MACHINES.. ................................................................... 2-73

C55 CONCRETE PUMPS.......................................................................................... 2-75

C60 CONCRETE SAWS (Add cost for sawblade wear)............................................. 2-77

C65 CONCRETE VIBRATORS.................................................................................. 2-79

EP 1110-1-8, Vol. 130 Nov 09

Index-2

C75 CRANES, HYDRAULIC, SELF-PROPELLED..................................................... 2-80

C80 CRANES, HYDRAULIC, TRUCK MOUNTED..................................................... 2-83

C85 CRANES, MECHANICAL, LATTICE BOOM, CRAWLER MOUNTED................ 2-85

C90 CRANES, MECHANICAL, LATTICE BOOM, TRUCK MOUNTED ..................... 2-90

C95 CRANES, TOWER ............................................................................................. 2-91

D10 DRILLS, HYDRAULIC TRACK (Add cost for drill steel and bit wear) ................. 2-94

D15 DRILLS, HORIZONTAL BORING & GROUND PIERCING (Add cost for

drill steel and bit wear) ...................................................................................... 2-96

D20 DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit

wear)................................................................................................................. 2-97

D25 DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear) ............... 2-98

D30 DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear)...... 2-100

D35 DRILLS, ROTARY BLASTHOLE (Add cost for drill steel and bit wear) ............ 2-101

F10 FORK LIFTS ..................................................................................................... 2-103

G10 GENERATOR SETS ........................................................................................ 2-104

G15 GRADERS, MOTOR ........................................................................................ 2-106

H10 HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear).............. 2-108

H13 HAZARDOUS/TOXIC WASTE EQUIPMENT ................................................... 2-110

H20 HOISTS & AIR WINCHES ................................................................................ 2-124

H25 HYDRAULIC EXCAVATORS, CRAWLER MOUNTED..................................... 2-125

H30 HYDRAULIC EXCAVATORS, WHEEL MOUNTED.......................................... 2-140

H35 HYDRAULIC SHOVELS, CRAWLER MOUNTED ............................................ 2-141

L10 LAND CLEARING EQUIPMENT ....................................................................... 2-142

L15 LANDSCAPING EQUIPMENT .......................................................................... 2-144

L20 LIGHTING SETS, TRAILER MOUNTED........................................................... 2-147

L25 LINE STRIPING EQUIPMENT .......................................................................... 2-148

L30 LOADERS, BELT (Conveyor belts) & ACCESSORIES..................................... 2-149

L35 LOADERS, FRONT END, CRAWLER TYPE .................................................... 2-150

L40 LOADERS, FRONT END, WHEEL TYPE ......................................................... 2-151

EP 1110-1-8, Vol. 130 Nov 09

Index-3

L50 LOADERS / BACKHOE, WHEEL TYPE............................................................ 2-155

L55 LOADER / BACKHOE, ATTACHMENTS .......................................................... 2-156

L60 LOG SKIDDERS ............................................................................................... 2-157

M10 MARINE EQUIPMENT (NON DREDGING) ..................................................... 2-158

P10 PILE HAMMER ACCESSORIES - EXTRACTORS & BOX LEADS .................. 2-163

P20 PILE HAMMERS, DOUBLE ACTING................................................................ 2-164

P25 PILE HAMMERS, SINGLE ACTING ................................................................. 2-165

P30 PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORY................................. 2-168

P35 PIPELAYERS.................................................................................................... 2-169

P40 PLATFORMS & MAN-LIFTS............................................................................. 2-169

P45 PUMPS, GROUT .............................................................................................. 2-171

P50 PUMPS, WATER, CENTRIFUGAL, TRASH..................................................... 2-174

P55 PUMPS, WATER, SUBMERSIBLE................................................................... 2-176

P60 PUMPS, WATER, CENTRIFUGAL, DEWATERING......................................... 2-177

P65 PUMPS, WATER, DIAPHRAGM....................................................................... 2-179

P70 PUMPS, WATER (For core drills) ..................................................................... 2-180

R10 RIPPERS & HYDRAULIC BANK SLOPERS (Add cost for point wear) ............ 2-181

R15 ROLLERS, STATIC, TOWED, PNEUMATIC.................................................... 2-183

R20 ROLLERS, STATIC, TOWED, STEEL DRUM.................................................. 2-184

R30 ROLLERS, STATIC, SELF-PROPELLED......................................................... 2-184

R40 ROLLERS, VIBRATORY, TOWED................................................................... 2-188

R45 ROLLERS, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM .................... 2-188

R50 ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE DRUM...................... 2-190

R55 ROOFING EQUIPMENT................................................................................... 2-193

S10 SCRAPERS, ELEVATING ................................................................................ 2-196

S15 SCRAPERS, CONVENTIONAL........................................................................ 2-196

S20 SCRAPERS, TANDEM POWERED.................................................................. 2-197

S25 SCRAPERS, TRACTOR DRAWN .................................................................... 2-198

S30 SCREENING & CRUSHING PLANTS .............................................................. 2-199

EP 1110-1-8, Vol. 130 Nov 09

Index-4

S35 SNOW REMOVAL EQUIPMENT ...................................................................... 2-213

S40 SOIL & ROAD STABILIZERS ........................................................................... 2-214

S45 SPLITTERS, ROCK & CONCRETE.................................................................. 2-215

T10 TRACTOR BLADES & ATTACHMENTS (including agricultural)....................... 2-215

T15 TRACTORS, CRAWLER (DOZER) (includes blade) ........................................ 2-218

T20 TRACTORS, WHEEL TYPE (DOZER) ............................................................. 2-222

T25 TRACTORS, AGRICULTURAL......................................................................... 2-222

T30 TRENCHERS, CHAIN TYPE CUTTER............................................................. 2-224

T35 TRENCHERS, WHEEL TYPE CUTTER ........................................................... 2-226

T40 TRUCK OPTIONS............................................................................................. 2-227

T45 TRUCK TRAILERS ........................................................................................... 2-232

T50 TRUCKS, HIGHWAY (Add attachments as required) ....................................... 2-237

T55 TRUCKS, OFF-HIGHWAY................................................................................ 2-240

T56 TRUCKS,OFF-HIGHWAY/PRIME MOVER TRACTORS & WAGONS ............. 2-243

T57 TRUCKS, VACUUM.......................................................................................... 2-243

T60 TRUCKS, WATER, OFF-HIGHWAY................................................................. 2-244

T65 TUNNEL/MINING EQUIPMENT........................................................................ 2-245

W25 WATER & CO2 BLASTERS............................................................................. 2-246

W30 WATER TANKS............................................................................................... 2-250

W35 WELDERS ....................................................................................................... 2-251

EP 1110-1-8, Vol. 130 Nov 09