Upload
others
View
7
Download
0
Embed Size (px)
Citation preview
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 1/141
DDR3(L) SDRAM 16M x 16 Bit x 8 Banks
DDR3(L) SDRAM
Feature
Interface and Power Supply
˗ SSTL_15: VDD/VDDQ = 1.5V(±0.075V)
˗ SSTL_135: VDD/VDDQ = 1.35V(-0.067V/+0.1V)
JEDEC DDR3(L) Compliant
˗ 8n Prefetch Architecture
˗ Differential Clock (CK/ CK ) and Data Strobe (DQS/ DQS )
˗ Double-data rate on DQs, DQS and DM
Data Integrity
˗ Auto Self Refresh (ASR) by DRAM built-in TS
˗ Auto Refresh and Self Refresh Modes
Power Saving Mode
˗ Power Down Mode
Signal Integrity
˗ Configurable DS for system compatibility
˗ Configurable On-Die Termination
˗ ZQ Calibration for DS/ODT impedance accuracy via
external ZQ pad (240 ohm ± 1%)
Signal Synchronization
˗ Write Leveling via MR settings1
˗ Read Leveling via MPR
Programmable Functions
˗ CAS Latency (5/6/7/8/9/10/11/13)
˗ CAS Write Latency (5/6/7/8/9)
˗ Additive Latency (0/CL-1/CL-2)
˗ Write Recovery Time (5/6/7/8/10/12/14/16)
˗ Burst Type (Sequential/Interleaved)
˗ Burst Length (BL8/BC4/BC4 or 8 on the fly)
˗ Self Refresh Temperature Range(Normal/Extended)
˗ Output Driver Impedance (34/40)
˗ On-Die Termination of Rtt_Nom(20/30/40/60/120)
˗ On-Die Termination of Rtt_WR(60/120)
˗ Precharge Power Down (slow/fast)
Note: 1. Only Support prime DQ’s feedback for each byte lane.
Ordering Information
Product ID Max Freq. VDD Data Rate
(CL-tRCD-tRP) Package Comments
M15T2G16128A –DEBIAG2L 933MHz 1.35/ 1.5V DDR3(L)-1866 (13-13-13) 96 ball BGA
(7.5mmx13.5mm)
Pb-free
M15T2G16128A –BDBIAG2L 800MHz 1.35/ 1.5V DDR3(L)-1600 (11-11-11) Pb-free
M15T2G16128A –DEBIAG2LS 933MHz 1.35/ 1.5V DDR3(L)-1866 (13-13-13) 96 ball BGA
(7.5mmx13mm)
Pb-free
M15T2G16128A –BDBIAG2LS 800MHz 1.35/ 1.5V DDR3(L)-1600 (11-11-11) Pb-free
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 2/141
Description
The 2Gb Double-Data-Rate-3(L) (DDR3(L)) DRAM is double data rate architecture to achieve high-speed operation. It is
internally configured as an eight bank DRAMs.
The 2Gb chip is organized as 16Mbit x 16 I/Os x 8 bank devices. These synchronous devices achieve high speed
double-data-rate transfer rates of up to 1866 Mb/sec/pin for general applications.
The chip is designed to comply with all key DDR3(L) DRAM key features and all of the control and address inputs are
synchronized with a pair of externally supplied differential clocks. Inputs are latched at the cross point of differential clocks (CK
rising and CK falling). All I/Os are synchronized with a single ended DQS or differential DQS pair in a source synchronous
fashion.
These devices operate with a single 1.35V -0.067V/+0.1V or 1.5V ± 0.075V power supply and are available in BGA packages.
DDR3(L) SDRAM Addressing
Configuration 128Mb x16
# of Bank 8
Bank Address BA0 – BA2
Auto precharge A10 / AP
BL switch on the fly A12 /BC
Row Address A0 – A13
Column Address A0 – A9
Page size 2KB
tREFI1 (us)
TOPER <= 85: 7.8;
TOPER > 85: 3.9
tRFC2 (ns) 160
Note:
1. If TOPER exceeds 85, the DRAM must be refreshed externally at 2x refresh, which is a 3.9us interval refresh rate. Extended
SRT or ASR must be enabled. 2. Violating tRFC specification will induce malfunction.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 3/141
Pin Configuration – 96 balls BGA Package
< TOP View>
See the balls through the package
1 2 3 4 5 6 7 8 9
A VDDQ DQU5 DQU7 DQU4 VDDQ VSS
B VSSQ VDD VSS DQSU DQU6 VSSQ
C VDDQ DQU3 DQU1 DQSU DQU2 VDDQ
D VSSQ VDDQ DMU DQU0 VSSQ VDD
E VSS VSSQ DQL0 DML VSSQ VDDQ
F VDDQ DQL2 DQSL DQL1 DQL3 VSSQ
G VSSQ DQL6 DQSL VDD VSS VSSQ
H VREFDQ VDDQ DQL4 DQL7 DQL5 VDDQ
J NC VSS RAS CK VSS NC
K ODT VDD CAS CK VDD CKE
L NC CS WE A10/AP ZQ NC
M VSS BA0 BA2 NC VREFCA VSS
N VDD A3 A0 A12/BC BA1 VDD
P VSS A5 A2 A1 A4 VSS
R VDD A7 A9 A11 A6 VDD
T VSS RESET A13 NC A8 VSS
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 4/141
Input / Output Functional Description
Symbol Type Function
CK, CK Input Clock: CK and CK are differential clock inputs. All address and control input signals are
sampled on the crossing of the positive edge of CK and negative edge of CK .
CKE Input
Clock Enable: CKE high activates, and CKE low deactivates, internal clock signals and
device input buffers and output drivers. Taking CKE low provides Precharge Power-Down and Self-Refresh operation (all banks idle), or Active Power-Down (row Active in any bank). CKE is synchronous for power down entry and exit and for Self-Refresh entry. CKE is asynchronous for Self-Refresh exit. After VREF has become stable during the power on and initialization sequence, it must be maintained for proper operation of the CKE receiver. For proper self-refresh entry and exit, VREF must maintain to this input. CKE must be
maintained high throughout read and write accesses. Input buffers, excluding CK, CK ,
ODT and CKE are disabled during Power Down. Input buffers, excluding CKE, are disabled during Self-Refresh.
CS Input
Chip Select: All commands are masked when CS is registered high. CS provides for
external rank selection on systems with multiple memory ranks. CS is considered part of
the command code.
RAS , CAS , WE Input Command Inputs: RAS , CAS and WE (along with CS ) define the command being
entered.
DM, (DMU, DML) Input
Input Data Mask: DM is an input mask signal for write data. Input data is masked when DM
is sampled HIGH coincident with that input data during a Write access. DM is sampled on both edges of DQS.
BA0 - BA2 Input
Bank Address Inputs: BA0, BA1, and BA2 define to which bank an Active, Read, Write or
Precharge command is being applied. Bank address also determines which mode register is to be accessed during a MRS cycle.
A10 / AP Input
Auto-Precharge: A10 is sampled during Read/Write commands to determine whether
Autoprecharge should be performed to the accessed bank after the Read/Write operation. (HIGH: Autoprecharge; LOW: no Autoprecharge). A10 is sampled during a Precharge command to determine whether the Precharge applies to one bank (A10 LOW) or all banks (A10 HIGH). If only one bank is to be precharged, the bank is selected by bank addresses.
A0 – A13 Input
Address Inputs: Provide the row address for Activate commands and the column address
for Read/Write commands to select one location out of the memory array in the respective
bank. (A10/AP and A12/ BC have additional function as below.) The address inputs also
provide the op-code during Mode Register Set commands.
A12/BC Input Burst Chop: A12/BC is sampled during Read and Write commands to determine if burst
chop (on the fly) will be performed. (HIGH - no burst chop; LOW - burst chopped).
ODT Input
On Die Termination: ODT (registered HIGH) enables termination resistance internal to the
DDR3(L) SDRAM. When enabled, ODT is applied to each DQ, DQS, DQS . The ODT pin
will be ignored if Mode-registers, MR1and MR2, are programmed to disable RTT.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 5/141
Symbol Type Function
RESET Input
Active Low Asynchronous Reset: Reset is active when RESET is LOW, and inactive
when RESET is HIGH. RESET must be HIGH during normal operation. RESET is a
CMOS rail to rail signal with DC high and low at 80% and 20% of VDD, i.e. 1.20V for DC high and 0.30V
DQ (DQL, DQU) Input/output Data Inputs/Output: Bi-directional data bus.
DQS, DQS
(DQSL, DQSL ,
DQSU, DQSU )
Input/output
Data Strobe: output with read data, input with write data. Edge aligned with read data,
centered with write data. The data strobes DQS (DQSL, DQSU) are paired with differential
signals DQS (DQSL , DQSU ), respectively, to provide differential pair signaling to the
system during both reads and writes. DDR3(L) SDRAM supports differential data strobe only and does not support single-ended.
NC - No Connect: No internal electrical connection is present.
VDDQ Supply DQ Power Supply: 1.35V -0.067V/+0.1V &1.5V ± 0.075V
VDD Supply Power Supply: 1.35V -0.067V/+0.1V & 1.5V ± 0.075V
VSSQ Supply DQ Ground
VSS Supply Ground
VREFCA Supply Reference voltage for CA
VREFDQ Supply Reference voltage for DQ
ZQ Supply Reference pin for ZQ calibration.
Note: Input only pins (BA0-BA2, A0-A13,RAS , CAS , WE , CS , CKE, ODT, and RESET ) do not supply termination.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 6/141
Simplified State Diagram
Power
ON
Power
Applied Reset
Procedure
From any
State RESET
Initialization
ZQ Calibration Idle
MRS, MPR,
Write
LevelizingSelf Refresh
Refreshing
SRE
SRX
REF
Activating
ACT
Precharge
Power
Down
PDE
PDX
Active
Power
Down
Bank
Active
Writing
Writing
Precharging
Reading
Write
Write A Read A
Write Read
Write A Read A
Write
Read
PRE,
PREA
PRE,
PREA
Write ARead A
PRE,
PREA
PDX
PDE
Reading
Read
Automatic
Sequence
Command
Sequence
MRSZQCL
ZQCL
ZQCS
State Diagram Command Definitions
Abbreviation Function Abbreviation Function Abbreviation Function
ACT Active Read RD, RDS4, RDS8 PDE Enter Power-down
PRE Precharge Read A RDA, RDAS4, RDAS8 PDX Exit Power-down
PREA Precharge All Write WR, WRS4, WRS8 SRE Self-Refresh entry
MRS Mode Register Set Write A WRA, WRAS4, WRAS8 SRX Self-Refresh exit
REF Refresh RESET Start RESET Procedure MPR Multi-Purpose Register
ZQCL ZQ Calibration Long ZQCS ZQ Calibration Short - -
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 7/141
Basic Functionality
The DDR3(L) SDRAM is a high-speed dynamic random access memory internally configured as an eight-bank DRAM. The DDR3(L) SDRAM uses an 8n prefetch architecture to achieve high speed operation. The 8n prefetch architecture is combined with an interface designed to transfer two data words per clock cycle at the I/O pins. A single read or write operation for the DDR3(L) SDRAM consists of a single 8n-bit wide, four clock data transfer at the internal DRAM core and two corresponding n-bit wide, one-half clock cycle data transfers at the I/O pins.
Read and write operation to the DDR3(L) SDRAM are burst oriented, start at a selected location, and continue for a burst length of eight or a ‘chopped’ burst of four in a programmed sequence. Operation begins with the registration of an Active command, which is then followed by a Read or Write command. The address bits registered coincident with the Active command are used to select the bank and row to be activated (BA0-BA2 select the bank; A0-A13 select the row). The address bit registered coincident with the Read or Write command are used to select the starting column location for the burst operation, determine if the auto precharge command is to be issued (via A10), and select BC4 or BL8 mode ‘on the fly’ (via A12) if enabled in the mode register.
Prior to normal operation, the DDR3(L) SDRAM must be powered up and initialized in a predefined manner. The following sections provide detailed information covering device reset and initialization, register definition, command descriptions and device operation.
RESET and Initialization Procedure
Power-up Initialization sequence
The Following sequence is required for POWER UP and Initialization
1. Apply power ( RESET is recommended to be maintained below 0.2 x VDD, all other inputs may be undefined). RESET
needs to be maintained for minimum 200μs with stable power. CKE is pulled “Low” anytime before RESET being
de-asserted (min. time 10ns). The power voltage ramp time between 300mV to VDDmin must be no greater than 200ms; and
during the ramp, VDD>VDDQ and (VDD-VDDQ) <0.3 Volts.
- VDD and VDDQ are driven from a single power converter output, AND
- The voltage levels on all pins other than VDD, VDDQ, VSS, VSSQ must be less than or equal to VDDQ and VDD on one side
and must be larger than or equal to VSSQ and VSS on the other side. In addition, VTT is limited to 0.95V max once power
ramp is finished, AND
- VREF tracks VDDQ/2.
OR
- Apply VDD without any slope reversal before or at the same time as VDDQ.
- Apply VDDQ without any slope reversal before or at the same time as VTT & VREF.
- The voltage levels on all pins other than VDD, VDDQ, VSS, VSSQ must be less than or equal to VDDQ and VDD on one side
and must be larger than or equal to VSSQ and VSS on the other side.
2. After RESET is de-asserted, wait for another 500us until CKE become active. During this time, the DRAM will start internal
state initialization; this will be done independently of external clocks.
3. Clock (CK, CK ) need to be started and stabilized for at least 10ns or 5tCK (which is larger) before CKE goes active. Since
CKE is a synchronous signal, the corresponding set up time to clock (tIS) must be meeting. Also a NOP or Deselect command
must be registered (with tIS set up time to clock) before CKE goes active. Once the CKE registered “High” after Reset, CKE
needs to be continuously registered “High” until the initialization sequence is finished, including expiration of tDLLK and tZQinit.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 8/141
4. The DDR3(L) DRAM will keep its on-die termination in high impedance state as long as RESET is asserted. Further, the
DRAM keeps its on-die termination in high impedance state after RESET de-assertion until CKE is registered HIGH. The
ODT input signal may be in undefined state until tIS before CKE is registered HIGH. When CKE is registered HIGH, the ODT
input signal may be statically held at either LOW or HIGH. If RTT_NOM is to be enabled in MR1, the ODT input signal must be
statically held LOW. In all cases, the ODT input signal remains static until the power up initialization sequence is finished,
including the expiration of tDLLK and tZQinit.
5. After CKE being registered high, wait minimum of Reset CKE Exit time, tXPR, before issuing the first MRS command to load
mode register. [tXPR=max (tXS, 5tCK)]
6. Issue MRS command to load MR2 with all application settings. (To issue MRS command for MR2, provide “Low” to BA0 and
BA2, “High” to BA1)
7. Issue MRS command to load MR3 with all application settings. (To issue MRS command for MR3, provide “Low” to BA2,
“High” to BA0 and BA1)
8. Issue MRS command to load MR1 with all application settings and DLL enabled. (To issue “DLL Enable” command, provide
“Low” to A0, “High” to BA0 and “Low” to BA1 and BA2)
9. Issue MRS Command to load MR0 with all application settings and “DLL reset”. (To issue DLL reset command, provide “High”
to A8 and “Low” to BA0-BA2)
10. Issue ZQCL command to starting ZQ calibration.
11. Wait for both tDLLK and tZQinit completed.
12. The DDR3(L) SDRAM is now ready for normal operation.
Reset and Initialization Sequence at Power- on Ramping (Cont’d)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 9/141
Reset Procedure at Stable Power (Cont’d)
The following sequence is required for RESET at no power interruption initialization.
1. Asserted RESET below 0.2*VDD anytime when reset is needed (all other inputs may be undefined). RESET needs to be
maintained for minimum 100ns. CKE is pulled “Low” before RESET being de-asserted (min. time 10ns).
2. Follow Power-up Initialization Sequence step 2 to 11.
3. The Reset sequence is now completed. DDR3(L) SDRAM is ready for normal operation.
Reset Procedure at Power Stable Condition
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 10/141
Register Definition
Programming the Mode Registers
For application flexibility, various functions, features, and modes are programmable in four Mode Registers, provided by the DDR3(L) SDRAM, as user defined variables and they must be programmed via a Mode Register Set (MRS) command. As the default values of the Mode Registers (MR) are not defined, contents of Mode Registers must be fully initialized and/or re-initial-ized, i.e. written, after power up and/or reset for proper operation. Also the contents of the Mode Registers can be altered by re-executing the MRS command during normal operation. When programming the mode registers, even if the user chooses to modify only a sub-set of the MRS fields, all address fields within the accessed mode register must be redefined when the MRS command is issued. MRS command and DLL Reset do not affect array contents, which mean these commands can be executed any time after power-up without affecting the array contents.
The mode register set command cycle time, tMRD is required to complete the write operation to the mode register and is the minimum time required between two MRS commands shown as below.
tMRD Timing
The MRS command to Non-MRS command delay, tMOD, is require for the DRAM to update the features except DLL reset, and is the minimum time required from an MRS command to a non-MRS command excluding NOP and DES shown as the following figure.
tMOD Timing
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 11/141
Programming the Mode Registers (Cont’d)
The mode register contents can be changed using the same command and timing requirements during normal operation as long as the DRAM is in idle state, i.e. all banks are in the precharged state with tRP satisfied, all data bursts are completed and CKE is high prior to writing into the mode register. The mode registers are divided into various fields depending on the functionality and/or modes.
Mode Register MR0
The mode-register MR0 stores data for controlling various operating modes of DDR3(L) SDRAM. It controls burst length, read burst type, CAS latency, test mode, DLL reset, WR, and DLL control for precharge Power-Down, which include various vendor specific options to make DDR3(L) SDRAM useful for various applications. The mode register is written by asserting low on
CS , RAS , CAS , WE , BA0, BA1, and BA2, while controlling the states of address pins according to the following figure.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 12/141
MR0 Definition
BA2 BA1 BA0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓
0 PPD DLL TM RBT CL
A12 A8 A3
0 0 0
1 1 1
BA1 BA0 A7
0 0 0 A1 A0
0 1 1 0 0
1 0 0 1
1 1 1 0
1 1
A11 A10 A9
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
A6 A5 A4 A2
0 0 0 0
0 0 1 0
0 1 0 0
0 1 1 0
1 0 0 0
1 0 1 0
1 1 0 0
1 1 1 0
0 0 0 1
0 0 1 1
0 1 0 1
0 1 1 1
1 0 0 1
1 0 1 1
1 1 0 1
1 1 1 1
Reserved
BL
10
11
12
13
Reserved
Reserved
Reserved
Reserved
Reserved
12
14
CAS Latency
Reserved
Reserved
5
6
7
8
9
6
7
8
10
WR
16
5
8(Fixed)
BC4 or 8(on the fly)
BC4(Fixed)
MR1
MR2
MR3
mode
Normal
Test
Nibble Sequential
Interleave
Read Burst Type
MR0
MR select
PPD
Slow exit(DLL off)
Fast exit(DLL on)
No
Yes
DLL Reset
A15-A13
MR select BLCAS LatencyWR0
↓
Note:
1. BA2 and A13~A15 are RFU and must be programmed to 0 during MRS.
2. WR (write recovery for autoprecharge)min in clock cycles is calculated by dividing tWR(in ns) by tCK(in ns) and rounding up to the next
integer: WRmin[cycles] = Roundup(tWR[ns] / tCK[ns]). The WR value in the mode register must be programmed to be equal or larger than
WRmin. The programmed WR value is used with tRP to determine tDAL.
3. The table only shows the encodings for a given Cas Latency. For actual supported Cas Latency, please refer to speedbin tables for each
frequency
4. The table only shows the encodings for Write Recovery. For actual Write recovery timing, please refer to AC timingtable.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 13/141
Burst Length, Type, and Order
Accesses within a given burst may be programmed to sequential or interleaved order. The burst type is selected via bit A3 as shown in the MR0 Definition as above figure. The ordering of access within a burst is determined by the burst length, burst type, and the starting column address. The burst length is defined by bits A0-A1. Burst lengths options include fix BC4, fixed BL8, and
on the fly which allow BC4 or BL8 to be selected coincident with the registration of a Read or Write command via A12/ BC .
Burst Type and Burst Order
Burst
Length
Read
Write
Starting
Column
Address
(A2,A1,A0)
Burst type:
Sequential
(decimal)
A3 = 0
Burst type:
Interleaved
(decimal)
A3 = 1
Note
4
Chop
Read
0,0,0 0,1,2,3,T,T,T,T 0,1,2,3,T,T,T,T
1,2,3
0,0,1 1,2,3,0,T,T,T,T 1,0,3,2,T,T,T,T
0,1,0 2,3,0,1,T,T,T,T 2,3,0,1,T,T,T,T
0,1,1 3,0,1,2,T,T,T,T 3,2,1,0,T,T,T,T
1,0,0 4,5,6,7,T,T,T,T 4,5,6,7,T,T,T,T
1,0,1 5,6,7,4,T,T,T,T 5,4,7,6,T,T,T,T
1,1,0 6,7,4,5,T,T,T,T 6,7,4,5,T,T,T,T
1,1,1 7,4,5,6,T,T,T,T 7,6,5,4,T,T,T,T
Write 0,V,V 0,1,2,3,X,X,X,X 0,1,2,3,X,X,X,X
1,2,4,5 1,V,V 4,5,6,7,X,X,X,X 4,5,6,7,X,X,X,X
8 Read
0,0,0 0,1,2,3,4,5,6,7 0,1,2,3,4,5,6,7
2
0,0,1 1,2,3,0,5,6,7,4 1,0,3,2,5,4,7,6
0,1,0 2,3,0,1,6,7,4,5 2,3,0,1,6,7,4,5
0,1,1 3,0,1,2,7,4,5,6 3,2,1,0,7,6,5,4
1,0,0 4,5,6,7,0,1,2,3 4,5,6,7,0,1,2,3
1,0,1 5,6,7,4,1,2,3,0 5,4,7,6,1,0,3,2
1,1,0 6,7,4,5,2,3,0,1 6,7,4,5,2,3,0,1
1,1,1 7,4,5,6,3,0,1,2 7,6,5,4,3,2,1,0
Write V,V,V 0,1,2,3,4,5,6,7 0,1,2,3,4,5,6,7 2,4
Note:
1. In case of burst length being fixed to 4 by MR0 setting, the internal write operation starts two clock cycles earlier than the
BL8 mode. This means that the starting point for tWR and tWTR will be pulled in by two clocks. In case of burst length
being selected on-the-fly via A12/ BC , the internal write operation starts at the same point in time like a burst of 8 write
operation. This means that during on-the-fly control, the starting point for tWR and tWTR will not be pulled in by two
clocks.
2. 0~7 bit number is value of CA [2:0] that causes this bit to be the first read during a burst.
3. T: Output driver for data and strobes are in high impedance.
4. V: a valid logic level (0 or 1), but respective buffer input ignores level on input pins.
5. X: Do not Care.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 14/141
CAS Latency
The CAS Latency is defined by MR0 (bit A2, A4~A6) as shown in the MR0 Definition figure. CAS Latency is the delay, in clock cycles, between the internal Read command and the availability of the first bit of output data. DDR3(L) SDRAM does not support any half clock latencies. The overall Read Latency (RL) is defined as Additive Latency (AL) + CAS Latency (CL); RL = AL + CL.
Test Mode
The normal operating mode is selected by MR0 (bit7=0) and all other bits set to the desired values shown in the MR0 definition figure. Programming bit A7 to a ‘1’ places the DDR3(L) SDRAM into a test mode that is only used by the DRAM manufacturer and should not be used. No operations or functionality is guaranteed if A7=1.
DLL Reset
The DLL Reset bit is self-clearing, meaning it returns back to the value of ‘0’ after the DLL reset function has been issued. Once the DLL is enabled, a subsequent DLL Reset should be applied. Anytime the DLL reset function is used, tDLLK must be met before any functions that require the DLL can be used (i.e. Read commands or ODT synchronous operations.)
Write Recovery
The programmed WR value MR0(bits A9, A10, and A11) is used for the auto precharge feature along with tRP to determine tDAL WR (write recovery for auto-precharge)min in clock cycles is calculated by dividing tWR(ns) by tCK(ns) and rounding up to the next integer: WRmin[cycles] = Roundup(tWR[ns]/tCK[ns]). The WR must be programmed to be equal or larger than tWR (min).
Precharge PD DLL
MR0 (bit A12) is used to select the DLL usage during precharge power-down mode. When MR0 (A12=0), or ‘slow-exit’, the DLL is frozen after entering precharge power-down (for potential power savings) and upon exit requires tXPDLL to be met prior to the next valid command. When MR0 (A12=1), or ‘fast-exit’, the DLL is maintained after entering precharge power-down and upon exiting power-down requires tXP to be met prior to the next valid command.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 15/141
Mode Register MR1
The Mode Register MR1 stores the data for enabling or disabling the DLL, output strength, Rtt_Nom impedance, additive latency,
WRITE leveling enable and Qoff. The Mode Register 1 is written by asserting low on CS , RAS , CAS , WE , high on BA0 and
low on BA1 and BA2, while controlling the states of address pins according to the following figure.
MR1 Definition
BA2 BA1 BA0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓
0 Qoff Rtt_Nom 0 Level Rtt_NomD.I.C Rtt_Nom D.I.C DLL
A9 A6 A2 A4 A3
0 0 0 0 0
0 0 1 0 1
0 1 0 1 0
BA1 BA0 0 1 1 1 1
0 0 1 0 0
0 1 1 0 1 A0
1 0 1 1 0 0
1 1 1 1 1 1
A7 A5 A1
0 0 0
1 0 1
1 0
1 1
A12
0
1
Qoff
Output buffer enable
0
Enable
Disable
Output buffer disable
Output Driver Impedance
RZQ/6
RZQ/7
Reserved
Reserved
Disable
Enable
RZQ/6
RZQ/12
RZQ/8
AL
Disable
CL-1
CL-2
Reserved
DLL Enable
A15-A13
MR select 0
↓
AL
MR0
MR Select
Rtt_Nom
Disable
RZQ/4
RZQ/2
Write Leveling enable
MR1
MR2
MR3
Reserved
Reserved
Note:
1. BA2 and A8, A10~A11, and A13 ~ A15 are RFU and must be programmed to 0 during MRS.
2. Outputs disabled - DQs, DQSs, DQS s.
3. RZQ=240.
4. In Write leveling Mode (MR1[bit7] = 1) with MR1[bit12]=1, all RTT_Nom settings are allowed; in Write Leveling Mode
(MR1[bit7] = 1) with MR1[bit12]=0, only RTT_Nom settings of RZQ/2, RZQ/4 and RZQ/6 are allowed.
5. If RTT_Nom is used during Writes, only the values RZQ/2, RZQ/4 and RZQ/6 are allowed.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 16/141
DLL Enable/Disable
The DLL must be enabled for normal operation. DLL enable is required during power up initialization, and upon returning to nor-
mal operation after having the DLL disabled. During normal operation (DLL-on) with MR1 (A0=0), the DLL is automatically dis-
abled when entering Self-Refresh operation and is automatically re-enable upon exit of Self-Refresh operation. Any time the DLL
is enabled and subsequently reset, tDLLK clock cycles must occur before a Read or synchronous ODT command can be issued
to allow time for the internal clock to be synchronized with the external clock. Failing to wait for synchronization to occur may
result in a violation of the tDQSCK, tAON, or tAOF parameters. During tDLLK, CKE must continuously be registered high.
DDR3(L) SDRAM does not require DLL for any Write operation, expect when RTT_WR is enabled and the DLL is required for
proper ODT operation. For more detailed information on DLL Disable operation in DLL-off Mode.
The direct ODT feature is not supported during DLL-off mode. The on-die termination resistors must be disabled by continuously
registering the ODT pin low and/or by programming the RTT_Nom bits MR1A9,A6,A2 to 0,0,0 via a mode register set
command during DLL-off mode.
The dynamic ODT feature is not supported at DLL-off mode. User must use MRS command to set Rtt_WR, MR2 A10, A9 = 0,
0, to disable Dynamic ODT externally.
Output Driver Impedance Control
The output driver impedance of the DDR3(L) SDRAM device is selected by MR1 (bit A1 and A5) as shown in MR1 definition
figure.
ODT Rtt Values
DDR3(L) SDRAM is capable of providing two different termination values (Rtt_Nom and Rtt_WR). The nominal termination value Rtt_Nom is programmable in MR1. A separate value (Rtt_WR) may be programmable in MR2 to enable a unique Rtt value when ODT is enabled during writes. The Rtt_WR value can be applied during writes even when Rtt_Nom is disabled.
Additive Latency (AL)
Additive Latency (AL) operation is supported to make command and data bus efficient for sustainable bandwidth in DDR3(L) SDRAM. In this operation, the DDR3(L) SDRAM allows a read or write command (either with or without auto-precharge) to be issued immediately after the active command. The command is held for the time of the Additive Latency (AL) before it is issued inside the device. The Read Latency (RL) is controlled by the sum of the AL and CAS Latency (CL) register settings. Write Latency (WL) is controlled by the sum of the AL and CAS Write Latency (CWL) register settings. A summary of the AL register options are shown as the following table.
Additive Latency (AL) Settings
A4 A3 AL
0 0 0, (AL Disable)
0 1 CL-1
1 0 CL-2
1 1 Reserved
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 17/141
Write leveling
For better signal integrity, DDR3(L) memory module adopted fly by topology for the commands, addresses, control signals, and clocks. The fly by topology has benefits from reducing number of stubs and their length but in other aspect, causes flight time skew between clock and strobe at every DRAM on DIMM. It makes difficult for the Controller to maintain tDQSS, tDSS, and tDSH specification. Therefore, the controller should support ‘write leveling’ in DDR3(L) SDRAM to compensate for skew.
Output Disable
The DDR3(L) SDRAM outputs maybe enable/disabled by MR1 (bit12) as shown in MR1 definition. When this feature is enabled
(A12=1) all output pins (DQs, DQS, DQS , etc.) are disconnected from the device removing any loading of the output drivers.
This feature may be useful when measuring modules power for example. For normal operation A12 should be set to ‘0’.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 18/141
Mode Register MR2
The Mode Register MR2 stores the data for controlling refresh related features, Rtt_WR impedance, and CAS write latency. The
Mode Register 2 is written by asserting low on CS , RAS , CAS , WE high on BA1 and low on BA0 and BA2, while controlling
the states of address pins according to the following figure.
MR2 Definition
BA2 BA1 BA0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓
0 0 SRT ASR
A6
0
1
A10 A9
0 0
0 1
1 0
1 1
A5 A4 A3
0 0 0
A7 0 0 1
0 1 0
0 1 1
1 0 0
1 1 0
1 1 0
BA1 BA0 1 1 1
0 0
0 1
1 0
1 1
RFU
MR0
MR1
MR2
MR3
Normal Operating
temperature range
Extended operation
temperature range
0
1
MR select
8 (1.5ns>=tCK(avg)>=1.25ns)
9 (1.25ns>=tCK(avg)>=1.07ns)
RFU
RFU
SRT
ASR
Manual SR Reference (SRT)
ASR enable
RZQ/2
Reserved
CWL
5 (tCK(avg)>=2.5ns)
6 (2.5ns>=tCK(avg)>=1.875ns)
7 (1.875ns>=tck(avg)>=1.5ns)
Rtt_Nom CWL 0
Rtt_WR
Dynamic ODT off
RZQ/4
A15-A13
MR select
↓
0
Note:
1. BA2, A5, A8, A11 ~ A15 are RFU and must be programmed to 0 during MRS.
2. The Rtt_WR value can be applied during writes even when Rtt_Nom is disabled. During write leveling, Dynamic ODT is not
available.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 19/141
CAS Write Latency (CWL)
The CAS Write Latency is defined by MR2 (bits A3-A5) shown in MR2. CAS Write Latency is the delay, in clock cycles, between the internal Write command and the availability of the first bit of input data. DDR3(L) DRAM does not support any half clock latencies. The overall Write Latency (WL) is defined as Additive Latency (AL) + CAS Write Latency (CWL); WL=AL+CWL.
Auto Self-Refresh (ASR) and Self-Refresh Temperature (SRT)
DDR3(L) SDRAM must support Self-Refresh operation at all supported temperatures. Applications requiring Self-Refresh opera-tion in the Extended Temperature Range must use the ASR function or program the SRT bit appropriately.
Optional in DDR3(L) SDRAM: Users should refer to the DRAM supplier data sheet and/or the DIMM SPD to determine if DDR3(L) SDRAM devices support the following options or requirements referred to in this material. For more details refer to “Extended Temperature Usage”. DDR3(L) SDRAMs must support Self-Refresh operation at all supported temperatures. Applications requiring Self-Refresh operation in the Extended Temperature Range must use the optional ASR function or program the SRT bit appropriately.
Dynamic ODT (Rtt_WR)
DDR3(L) SDRAM introduces a new feature “Dynamic ODT”. In certain application cases and to further enhance signal integrity on the data bus, it is desirable that the termination strength of the DDR3(L) SDRAM can be changed without issuing an MRS command. MR2 Register locations A9 and A10 configure the Dynamic ODT settings. In Write leveling mode, only RTT_Nom is available. For details on Dynamic ODT operation, refer to “Dynamic ODT”.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 20/141
Mode Register MR3
The Mode Register MR3 controls Multi-purpose registers. The Mode Register 3 is written by asserting low on CS ,RAS , CAS ,
WE high on BA1 and BA0, and low on BA2 while controlling the states of address pins according to the following figure.
MR3 Definition
BA2 BA1 BA0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓
0 MPR
A2 A1 A0
0 0 0
1 0 1
1 0
BA1 BA0 1 1
0 0
0 1
1 0
1 1
A15-A13
MR select
↓
MR select
MPR Loc0
MR0
Reserved
ASR
Normal operation
Dataflow from MPR
Reserved
MR3
MPR Loc
Predefined pattern
MR1
MR2
Reserved
Note:
1. BA2, A3 - A15 are RFU and must be programmed to 0 during MRS
2. The predefined pattern will be used for read synchronization.
3. When MPR control is set for normal operation (MR3 A[2] = 0) then MR3 A[1:0] will be ignored.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 21/141
Multi-Purpose Register (MPR)
The Multi Purpose Register (MPR) function is used to Read out a predefined system timing calibration bit sequence. To enable the MPR, a Mode Register Set (MRS) command must be issued to MR3 register with bit A2=1. Prior to issuing the MRS command, all banks must be in the idle state (all banks precharged and tRP met). Once the MPR is enabled, any subsequent RD or RDA commands will be redirected to the Multi Purpose Register. When the MPR is enabled, only RD or RDA commands are allowed until a subsequent MRS command is issued with the MPR disabled (MR3 bit A2=0). Power down mode, Self-Refresh and any other non-RD/RDA command is not allowed during MPR enable mode. The RESET function is supported during MPR enable mode.
The Multi Purpose Register (MPR) function is used to Read out a predefined system timing calibration bit sequence.
MPR Block Diagram
To enable the MPR, a MODE Register Set (MRS) command must be issued to MR3 Register with bit A2 = 1, prior to issuing the MRS command, all banks must be in the idle state (all banks precharged and tRP met). Once the MPR is enabled, any subsequent RD or RDA commands will be redirected to the Multi Purpose Register. The resulting operation, when a RD or RDA command is issued, is defined by MR3 bits A[1:0] when the MPR is enabled as shown. When the MPR is enabled, only RD or RDA commands are allowed until a subsequent MRS command is issued with the MPR disabled (MR3 bit A2 = 0). Note that in MPR mode RDA has the same functionality as a READ command which means the auto precharge part of RDA is ignored. Power-Down mode, Self-Refresh and any other non-RD/RDA command is not allowed during MPR enable mode. The RESET function is supported during MPR enable mode.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 22/141
MPR MR3 Register Definition
MR3 A[2] MR3 A[1:0] Function
MPR MPR-Loc
0b don't care (0b or 1b)
Normal operation, no MPR transaction.
All subsequent Reads will come from DRAM array.
All subsequent Write will go to DRAM array.
1b See MR3 Table Enable MPR mode, subsequent RD/RDA commands defined by MR3 A[1:0].
MPR Functional Description
•One bit wide logical interface via all DQ pins during READ operation.
•Register Read:
•DQL[0] and DQU[0] drive information from MPR.
•DQL[7:1] and DQU[7:1] either drive the same information as DQL [0], or they drive 0b.
•Addressing during for Multi Purpose Register reads for all MPR agents:
•BA [2:0]: don’t care
•A[1:0]: A[1:0] must be equal to ‘00’b. Data read burst order in nibble is fixed
•A[2]: For BL=8, A[2] must be equal to 0b, burst order is fixed to [0,1,2,3,4,5,6,7], *) For Burst Chop 4 cases, the burst order is
switched on nibble base A [2]=0b, Burst order: 0,1,2,3 *) A[2]=1b, Burst order: 4,5,6,7 *)
•A[9:3]: don’t care
•A10/AP: don’t care
•A12/ BC : Selects burst chop mode on-the-fly, if enabled within MR0.
•A11, A13... (if available): don’t care
•Regular interface functionality during register reads:
•Support two Burst Ordering which are switched with A2 and A[1:0]=00b.
•Support of read burst chop (MRS and on-the-fly via A12/ BC )
•All other address bits (remaining column address bits including A10, all bank address bits) will be ignored by the DDR3(L)
SDRAM.
•Regular read latencies and AC timings apply.
•DLL must be locked prior to MPR Reads.
NOTE:
1. Burst order bit 0 is assigned to LSB and burst order bit 7 is assigned to MSB of the selected MPR agent.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 23/141
MPR Register Address Definition
The following table provide an overview of the available data location, how they are addressed by MR3 A[1:0] during a MRS to
MR3, and how their individual bits are mapped into the burst order bits during a Multi Purpose Register Read.
MPR MR3 Register Definition
MR3 A[2] MR3 A[1:0] Function Burst Length Read Address
A[2:0]
Burst Order
and Data Pattern
1b 00b
Read Predefined
Pattern for System
Calibration
BL8 000b
Burst order 0,1,2,3,4,5,6,7
Pre-defined Data Pattern
[0,1,0,1,0,1,0,1]
BC4 000b
Burst order 0,1,2,3 Pre-defined Data
Pattern [0,1,0,1]
BC4 100b
Burst order 4,5,6,7
Pre-defined Data Pattern [0,1,0,1]
1b 01b RFU
BL8 000b Burst order 0,1,2,3,4,5,6,7
BC4 000b Burst order 0,1,2,3
BC4 100b Burst order 4,5,6,7
1b 10b RFU
BL8 000b Burst order 0,1,2,3,4,5,6,7
BC4 000b Burst order 0,1,2,3
BC4 100b Burst order 4,5,6,7
1b 11b RFU
BL8 000b Burst order 0,1,2,3,4,5,6,7
BC4 000b Burst order 0,1,2,3
BC4 100b Burst order 4,5,6,7
NOTE:
1. Burst order bit 0 is assigned to LSB and the burst order bit 7 is assigned to MSB of the selected MPR agent.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 24/141
DDR3(L) SDRAM Command Description and Operation
Command Truth Table
Function Abbreviation
CKE
CS RAS CAS W E
BA0-
BA2
A13 A12-
BC
A10-
AP
A0-A9,
A11
NOTES Previous
Cycle
Current
Cycle
Mode Register Set MRS H H L L L L BA OP Code
Refresh REF H H L L L H V V V V V
Self Refresh Entry SRE H L L L L H V V V V V 7,9,12
Self Refresh Exit SRX L H H X X X X X X X X
7,8,9,12 L H H H V V V V V
Single Bank Precharge PRE H H L L H L BA V V L V
Precharge all Banks PREA H H L L H L V V V H V
Bank Activate ACT H H L L H H BA Row Address (RA)
Write (Fixed BL8 or BC4) WR H H L H L L BA RFU V L CA
Write (BC4, on the Fly) WRS4 H H L H L L BA RFU L L CA
Write (BL8, on the Fly) WRS8 H H L H L L BA RFU H L CA
Write with Auto Precharge (Fixed BL8 or BC4) WRA H H L H L L BA RFU V H CA
Write with Auto Precharge (BC4, on the Fly) WRAS4 H H L H L L BA RFU L H CA
Write with Auto Precharge (BL8, on the Fly) WRAS8 H H L H L L BA RFU H H CA
Read (Fixed BL8 or BC4) RD H H L H L H BA RFU V L CA
Read (BC4, on the Fly RDS4 H H L H L H BA RFU L L CA
Read (BL8, on the Fly) RDS8 H H L H L H BA RFU H L CA
Read with Auto Precharge (Fixed BL8 or BC4) RDA H H L H L H BA RFU V H CA
Read with Auto Precharge (BC4, on the Fly) RDAS4 H H L H L H BA RFU L H CA
Read with Auto Precharge (BL8, on the Fly) RDAS8 H H L H L H BA RFU H H CA
No Operation NOP H H L H H H V V V V V 10
Device Deselected DES H H H X X X X X X X X 11
Power Down Entry PDE H L L H H H V V V V V
6,12 H X X X X X X X X
Power Down Exit PDX L H L H H H V V V V V
6,12 H X X X X X X X X
ZQ Calibration Long ZQCL H H L H H L X X X H X
ZQ Calibration Short ZQCS H H L H H L X X X L X
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 25/141
DDR3(L) SDRAM Command Description and Operation
Command Truth Table (Conti.)
Note:
1. All DDR3(L) SDRAM commands are defined by states of CS , RAS , CAS , WE and CKE at the rising edge of the clock. The
MSB of BA, RA and CA are device density and configuration dependant.
2. RESET is Low enable command which will be used only for asynchronous reset so must be maintained HIGH during any
function.
3. Bank addresses (BA) determine which bank is to be operated upon. For (E)MRS BA selects an (Extended) Mode Register.
4. “V” means “H or L (but a defined logic level)” and “X” means either “defined or undefined (like floating) logic level”.
5. Burst reads or writes cannot be terminated or interrupted and Fixed/on-the-Fly BL will be defined by MRS.
6. The Power-Down Mode does not perform any refresh operation.
7. The state of ODT does not affect the states described in this table. The ODT function is not available during Self Refresh.
8. Self Refresh Exit is asynchronous.
9. VREF (Both VrefDQ and VrefCA) must be maintained during Self Refresh operation.
10. The No Operation command should be used in cases when the DDR3(L) SDRAM is in an idle or wait state. The purpose of
the No Operation command (NOP) is to prevent the DDR3(L) SDRAM from registering any unwanted commands between
operations. A No Operation command will not terminate a pervious operation that is still executing, such as a burst read or
write cycle.
11. The Deselect command performs the same function as No Operation command.
12. Refer to the CKE Truth Table for more detail with CKE transition.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 26/141
CKE Truth Table
Current State
CKE
Command (N)
RAS , CAS , W E, CS Action (N) Notes Previous Cycle
(N-1)
Current Cycle
(N)
Power-Down L L X Maintain Power-Down 14,15
L H DESELECT or NOP Power-Down Exit 11,14
Self-Refresh L L X Maintain Self-Refresh 15,16
L H DESELECT or NOP Self-Refresh Exit 8,12,16
Bank(s) Active H L DESELECT or NOP Active Power-Down Entry 11,13,14
Reading H L DESELECT or NOP Power-Down Entry 11,13,14,17
Writing H L DESELECT or NOP Power-Down Entry 11,13,14,17
Precharging H L DESELECT or NOP Power-Down Entry 11,13,14,17
Refreshing H L DESELECT or NOP Precharge Power-Down Entry 11
All Banks Idle H L DESELECT or NOP Precharge Power-Down Entry 11,13,14,18
H L REFRESH Self-Refresh 9,13,18
Note:
1. CKE (N) is the logic state of CKE at clock edge N; CKE (N-1) was the state of CKE at the previous clock edge.
2. Current state is defined as the state of the DDR3(L) SDRAM immediately prior to clock edge N.
3. COMMAND (N) is the command registered at clock edge N, and ACTION (N) is a result of COMMAND (N), ODT is not included here.
4. All states and sequences not shown are illegal or reserved unless explicitly described elsewhere in this document.
5. The state of ODT does not affect the states described in this table. The ODT function is not available during Self-Refresh.
6. CKE must be registered with the same value on tCKEmin consecutive positive clock edges. CKE must remain at the valid
input level the entire time it takes to achieve the tCKEmin clocks of registrations. Thus, after any CKE transition, CKE may
not transition from its valid level during the time period of tIS + tCKEmin + tIH.
7. DESELECT and NOP are defined in the Command Truth Table.
8. On Self-Refresh Exit DESELECT or NOP commands must be issued on every clock edge occurring during the tXS period. Read or ODT commands may be issued only after tXSDLL is satisfied.
9. Self-Refresh modes can only be entered from the All Banks Idle state.
10. Must be a legal command as defined in the Command Truth Table.
11. Valid commands for Power-Down Entry and Exit are NOP and DESELECT only.
12. Valid commands for Self-Refresh Exit are NOP and DESELECT only.
13. Self-Refresh cannot be entered during Read or Write operations.
14. The Power-Down does not perform any refresh operations.
15. “X” means “don’t care“(including floating around VREF) in Self-Refresh and Power-Down. It also applies to Address pins.
16. VREF (Both Vref_DQ and Vref_CA) must be maintained during Self-Refresh operation.
17. If all banks are closed at the conclusion of the read, write or precharge command, then Precharge Power-Down is entered, otherwise Active Power-Down is entered.
18. ‘Idle state’ is defined as all banks are closed (tRP, tDAL, etc. satisfied), no data bursts are in progress, CKE is high, and all timings from previous operations are satisfied (tMRD, tMOD, tRFC, tZQinit, tZQoper, tZQCS, etc.) as well as all Self-Refresh exit and Power-Down Exit parameters are satisfied (tXS, tXP, tXPDLL, etc).
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 27/141
No Operation (NOP) Command
The No operation (NOP) command is used to instruct the selected DDR3(L) SDRAM to perform a NOP ( CS low and RAS ,
CAS , and WE high). This prevents unwanted commands from being registered during idle or wait states. Operations already
in progress are not affected.
Deselect Command
The Deselect function ( CS HIGH) prevents new commands from being executed by the DDR3(L) SDRAM. The DDR3(L)
SDRAM is effectively deselected. Operations already in progress are not affected.
DLL- Off Mode
DDR3(L) DLL-off mode is entered by setting MR1 bit A0 to “1”; this will disable the DLL for subsequent operations until A0 bit set back to “0”. The MR1 A0 bit for DLL control can be switched either during initialization or later.
The DLL-off Mode operations listed below are an optional feature for DDR3(L). The maximum clock frequency for DLL-off Mode is specified by the parameter tCKDLL_OFF. There is no minimum frequency limit besides the need to satisfy the refresh interval, tREFI.
Due to latency counter and timing restrictions, only one value of CAS Latency (CL) in MR0 and CAS Write Latency (CWL) in MR2 are supported. The DLL-off mode is only required to support setting of both CL=6 and CWL=6.
DLL-off mode will affect the Read data Clock to Data Strobe relationship (tDQSCK) but not the data Strobe to Data relationship (tDQSQ, tQH). Special attention is needed to line up Read data to controller time domain.
Comparing with DLL-on mode, where tDQSCK starts from the rising clock edge (AL+CL) cycles after the Read command, the DLL-off mode tDQSCK starts (AL+CL-1) cycles after the read command. Another difference is that tDQSCK may not be small compared to tCK (it might even be larger than tCK) and the difference between tDQSCKmin and tDQSCKmax is significantly larger than in DLL-on mode.
The timing relations on DLL-off mode READ operation have shown at the following Timing Diagram (CL=6, BL=8)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 28/141
DLL-off mode READ Timing Operation
Note:
1. The tDQSCK is used here for DQS, DQS , and DQ to have a simplified diagram; the DLL_off shift will affect both timings in the
same way and the skew between all DQ, DQS, and DQS signals will still be tDQSQ.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 29/141
DLL on/off switching procedure
DDR3(L) DLL-off mode is entered by setting MR1 bit A0 to “1”; this will disable the DLL for subsequent operation until A0 bit set back to “0”.
DLL “on” to DLL “off” Procedure
To switch from DLL “on” to DLL “off” requires the frequency to be changed during Self-Refresh outlined in the following procedure:
1. Starting from Idle state (all banks pre-charged, all timing fulfilled, and DRAMs On-die Termination resistors, RTT, must be in high impedance state before MRS to MR1 to disable the DLL).
2. Set MR1 Bit A0 to “1” to disable the DLL.
3. Wait tMOD.
4. Enter Self Refresh Mode; wait until (tCKSRE) satisfied.
5. Change frequency, in guidance with “Input Clock Frequency Change” section.
6. Wait until a stable clock is available for at least (tCKSRX) at DRAM inputs.
7. Starting with the Self Refresh Exit command, CKE must continuously be registered HIGH until all tMOD timings from any MRS command are satisfied. In addition, if any ODT features were enabled in the mode registers when Self Refresh mode was entered, the ODT signal must continuously be registered LOW until all tMOD timings from any MRS command are satisfied. If both ODT features were disabled in the mode registers when Self Refresh mode was entered, ODT signal can be registered LOW or HIGH.
8. Wait tXS, and then set Mode Registers with appropriate values (especially an update of CL, CWL, and WR may be necessary. A ZQCL command may also be issued after tXS).
9. Wait for tMOD, and then DRAM is ready for next command.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 30/141
DLL Switch Sequence from DLL-on to DLL-off
Note:
ODT: Static LOW in case RTT_Nom and RTT_WR is enabled, otherwise static Low or High
1. Starting with Idle State, RTT in Hi-Z State.
2. Disable DLL by setting MR1 Bit A0 to 1
3. Enter SR.
4. Change Frequency.
5. Clock must be stable at least tCKSRX.
6. Exit SR.
7. Update Mode registers with DLL off parameters setting.
8. Any valid command.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 31/141
DLL “off” to DLL “on” Procedure
To switch from DLL “off” to DLL “on” (with requires frequency change) during Self-Refresh:
1. Starting from Idle state (all banks pre-charged, all timings fulfilled and DRAMs On-die Termination resistors (RTT) must be in
high impedance state before Self-Refresh mode is entered).
2. Enter Self Refresh Mode, wait until tCKSRE satisfied.
3. Change frequency, in guidance with “Input clock frequency change” section.
4. Wait until a stable is available for at least (tCKSRX) at DRAM inputs.
5. Starting with the Self Refresh Exit command, CKE must continuously be registered HIGH until tDLLK timing from subsequent
DLL Reset command is satisfied. In addition, if any ODT features were enabled in the mode registers when Self Refresh
mode was entered. The ODT signal must continuously be registered LOW until tDLLK timings from subsequent DLL Reset
command is satisfied. If both ODT features are disabled in the mode registers when Self Refresh mode was entered, ODT
signal can be registered LOW or HIGH.
6. Wait tXS, then set MR1 Bit A0 to “0” to enable the DLL.
7. Wait tMRD, then set MR0 Bit A8 to “1” to start DLL Reset.
8. Wait tMRD, then set Mode registers with appropriate values (especially an update of CL, CWL, and WR may be necessary.
After tMOD satisfied from any proceeding MRS command, a ZQCL command may also be issued during or after tDLLK).
9. Wait for tMOD, then DRAM is ready for next command (remember to wait tDLLK after DLL Reset before applying command
requiring a locked DLL!). In addition, wait also for tZQoper in case a ZQCL command was issued.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 32/141
DLL Switch Sequence from DLL-off to DLL-on
Note:
ODT: Static LOW in case RTT_Nom and RTT_WR is enabled, otherwise static Low or High
1. Starting from Idle State.
2. Enter SR.
3. Change Frequency.
4. Clock must be stable at least tCKSRX.
5. Exit SR.
6. Set DLL-on by MR1=”0”
7. Start DLL Reset.
8. Any valid command
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 33/141
Input Clock frequency change
Once the DDR3(L) SDRAM is initialized, the DDR3(L) SDRAM requires the clock to be “stable” during almost all states of normal operation. This means once the clock frequency has been set and is to be in the “stable state”, the clock period is not allowed to deviate except for what is allowed for by the clock jitter and SSC (spread spectrum clocking) specification.
The input clock frequency can be changed from one stable clock rate to another stable clock rate under two conditions: (1) Self-Refresh mode and (2) Precharge Power-Down mode. Outside of these two modes, it is illegal to change the clock frequency.
For the first condition, once the DDR3(L) SDRAM has been successfully placed in to Self-Refresh mode and tCKSRE has been satisfied, the state of the clock becomes a don’t care. Once a don’t care, changing the clock frequency is permissible, provided the new clock frequency is stable prior to tCKSRX. When entering and exiting Self-Refresh mode of the sole purpose of changing the clock frequency. The DDR3(L) SDRAM input clock frequency is allowed to change only within the minimum and maximum operating frequency specified for the particular speed grade.
The second condition is when the DDR3(L) SDRAM is in Precharge Power-Down mode (either fast exit mode or slow exit mode). If the RTT_Nom feature was enabled in the mode register prior to entering Precharge power down mode, the ODT signal must continuously be registered LOW ensuring RTT is in an off state. If the RTT_Nom feature was disabled in the mode register prior to entering Precharge power down mode, RTT will remain in the off state. The ODT signal can be registered either LOW or HIGH in this case. A minimum of tCKSRE must occur after CKE goes LOW before the clock frequency may change. The DDR3(L) SDRAM input clock frequency is allowed to change only within the minimum and maximum operating frequency specified for the particular speed grade. During the input clock frequency change, ODT and CKE must be held at stable LOW levels. Once the input clock frequency is changed, stable new clocks must be provided to the DRAM tCKSRX before precharge Power Down may be exited; after Precharge Power Down is exited and tXP has expired, the DLL must be RESET via MRS. Depending on the new clock frequency additional MRS commands may need to be issued to appropriately set the WR, CL, and CWL with CKE continuously registered high. During DLL re-lock period, ODT must remain LOW and CKE must remain HIGH. After the DLL lock time, the DRAM is ready to operate with new clock frequency.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 34/141
Change Frequency during Precharge Power-down
Notes:
1. Applicable for both SLOW EXIT and FAST EXIT Precharge Power-down
2. tAOFPD and tAOF must be statisfied and outputs High-Z prior to T1; refer to ODT timing section for exact requirements
3. If the RTT_NOM feature was enabled in the mode register prior to entering Precharge power down mode, the ODT signal
must continuously be registered LOW ensuring RTT is in an off state. If the RTT_NOM feature was disabled in the mode
register prior to entering Precharge power down mode, RTT will remain in the off state. The ODT signal can be registered
either LOW or HIGH in this case.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 35/141
Write Leveling
For better signal integrity, DDR3(L) memory adopted fly by topology for the commands, addresses, control signals, and clocks. The fly by topology has benefits from reducing number of stubs and their length but in other aspect, causes flight time skew between clock and strobe at every DRAM on DIMM. It makes it difficult for the Controller to maintain tDQSS, tDSS, and tDSH specification. Therefore, the controller should support “write leveling” in DDR3(L) SDRAM to compensate the skew.
The memory controller can use the “write leveling” feature and feedback from the DDR3(L) SDRAM to adjust the DQS -DQS to
CK - CK relationship. The memory controller involved in the leveling must have adjustable delay setting on DQS -DQS to
align the rising edge of DQS - DQS with that of the clock at the DRAM pin. DRAM asynchronously feeds back CK - CK ,
sampled with the rising edge of DQS - DQS , through the DQ bus. The controller repeatedly delays DQS - DQS until a transition
from 0 to 1 is detected. The DQS - DQS delay established though this exercise would ensure tDQSS specification. Besides
tDQSS, tDSS, and tDSH specification also needs to be fulfilled. One way to achieve this is to combine the actual tDQSS in the
application with an appropriate duty cycle and jitter on the DQS -DQS signals. Depending on the actual tDQSS in the
application, the actual values for tDQSL and tDQSH may have to be better than the absolute limits provided in “AC Timing Parameters” section in order to satisfy tDSS and tDSH specification. A conceptual timing of this scheme is show as below figure.
Write Leveling Concept
DQS/ DQS driven by the controller during leveling mode must be determined by the DRAM based on ranks populated. Similarly,
the DQ bus driven by the DRAM must also be terminated at the controller.
One or more data bits should carry the leveling feedback to the controller across the DRAM configurations x16. On a x16 device,
both byte lanes should be leveled independently. Therefore, a separate feedback mechanism should be able for each byte lane.
The upper data bits should provide the feedback of the upper diff_DQS (diff_UDQS) to clock relationship whereas the lower data
bits would indicate the lower diff_DQS (diff_LDQS) to clock relationship.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 36/141
DRAM setting for write leveling and DRAM termination unction in that mode
DRAM enters into Write leveling mode if A7 in MR1 set “High” and after finishing leveling, DRAM exits from write leveling mode if
A7 in MR1 set “Low”. Note that in write leveling mode, only DQS/ DQS terminations are activated and deactivated via ODT pin
not like normal operation.
MR setting involved in the leveling procedure
Function MR1 Enable Disable
Write leveling enable A7 1 0
Output buffer mode (Qoff) A12 0 1
DRAM termination function in the leveling mode
ODT pin at DRAM DQS/ DQS termination DQs termination
De-asserted off off
Asserted on off
Note:
1. In write leveling mode with its output buffer disabled (MR1[bit7]=1 with MR1[bit12]=1) all RTT_Nom settings are allowed; in Write Leveling Mode with its output buffer enabled (MR1[bit7]=1 with MR1[bit12]=0) only RTT_Nom settings of RZQ/2, RZQ/4, and RZQ/6 are allowed.
Procedure Description
Memory controller initiates Leveling mode of all DRAMs by setting bit 7 of MR1 to 1. With entering write leveling mode, the DQ pins are in undefined driving mode. During write leveling mode, only NOP or Deselect commands are allowed. As well as an MRS command to exit write leveling mode. Since the controller levels one rank at a time, the output of other rank must be disabled by setting MR1 bit A12 to 1. Controller may assert ODT after tMOD, time at which DRAM is ready to accept the ODT signal.
Controller may drive DQS low and DQS high after a delay of tWLDQSEN, at which time DRAM has applied on-die termination
on these signals. After tDQSL and tWLMRD controller provides a single DQS, DQS edge which is used by the DRAM to sample
CK – CK driven from controller. tWLMRD (max) timing is controller dependent.
DRAM samples CK - CK
tWLO timing. There is a DQ output uncertainty of tWLOE defined to allow mismatch on DQ bits; there are no read strobes
(DQS/ DQS ) needed for these DQs. Controller samples incoming DQ and decides to increment or decrement DQS –DQS delay
setting and launches the next DQS/ DQS pulse after some time, which is controller dependent. Once a 0 to 1 transition is
detected, the controller locks DQS – DQS delay setting and write leveling is achieved for the device. The following figure
describes the timing diagram and parameters for the overall Write leveling procedure.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 37/141
Timing details of Write leveling sequence (For Information. Only Support prime DQ)
DQS -DQS is capturing CK -CK low at T1 and CK -CK high at T2
Notes:
1. DRAM has the option to drive leveling feedback on a prime DQ or all DQs. If feedback is driven only on one DQ, the
remaining DQs must be driven low as shown in above Figure, and maintained at this state through out the leveling
procedure.
2. MRS: Load MR1 to enter write leveling mode.
3. NOP: NOP or deselect.
4. diff_DQS is the differential data strobe (DQS, DQS ). Timing reference points are the zero crossings. DQS is shown with
solid line, DQS is shown with dotted line.
5. DQS/ DQS needs to fulfill minimum pulse width requirements tDQSH(min) and tDQSL(min) as defined for reqular Writes; the
max pulse width is system dependent.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 38/141
Write Leveling Mode Exit
The following sequence describes how Write Leveling Mode should be exited:
1. After the last rising strobe edge (see ~T0), stop driving the strobe signals (see ~Tc0). Note: From now on, DQ pins are in undefined driving mode, and will remain undefined, until tMOD after the respective MR command (Te1).
2. Drive ODT pin low (tIS must be satisfied) and keep it low (see Tb0).
3. After the RTT is switched off, disable Write Level Mode via MRS command (see Tc2).
4. After tMOD is satisfied (Te1), any valid command may be registered. (MR commands may be issued after tMRD (Td1).
Timing detail of Write Leveling exit
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 39/141
Extended Temperature Usage
DDR3(L) SDRAM supports the optional extended temperature range of -40°C to +105°C , TC. Thus, the SRT and ASR options must be used at a minimum. The extended temperature range DRAM must be refreshed externally at 2X (double refresh) anytime the case temperature is above +85°C (in supporting temperature range). The external refreshing requirement is accomplished by reducing the refresh period from 64ms to 32ms.If TC is above 95°C, self refresh period must be 16ms. However, self refresh mode requires either ASR or SRT to support the extended temperature. Thus either ASR or SRT must be enabled when TC is above +85°C or self refresh cannot be used until the case temperature is at or below +85°C.
Mode Register Description
Field Bits Description
ASR MR2(A6)
Auto Self-Refresh (ASR)
When enabled, DDR3(L) SDRAM automatically provides Self-Refresh power management
functions for all supported operating temperature values. If not enabled, the SRT bit must be
programmed to indicate TOPER during subsequent Self-Refresh operation.
0 = Manual SR Reference (SRT)
1 = ASR enable
SRT MR2(A7)
Self-Refresh Temperature (SRT) Range
If ASR = 0, the SRT bit must be programmed to indicate TOPER during subsequent Self-Refresh
operation. If ASR = 1, SRT bit must be set to 0.
0 = Normal operating temperature range
1 = Extended operating temperature range
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 40/141
Auto Self-Refresh mode - ASR mode
DDR3(L) SDRAM provides an Auto-Refresh mode (ASR) for application ease. ASR mode is enabled by setting MR2 bit A6=1 and MR2 bit A7=0. The DRAM will manage Self-Refresh entry in either the Normal or Extended Temperature Ranges. In this mode, the DRAM will also manage Self-Refresh power consumption when the DRAM operating temperature changes, lower at low temperatures and higher at high temperatures. If the ASR option is not supported by DRAM, MR2 bit A6 must set to 0. If the ASR option is not enabled (MR2 bit A6=0), the SRT bit (MR2 bit A7) must be manually programmed with the operating temperature range required during Self-Refresh operation. Support of the ASR option does not automatically imply support of the Extended Temperature Range.
Self-Refresh Temperature Range - SRT
SRT applies to devices supporting Extended Temperature Range only. If ASR=0, the Self-Refresh Temperature (SRT) Range bit must be programmed to guarantee proper self-refresh operation. If SRT=0, then the DRAM will set an appropriate refresh rate for Self-Refresh operation in the Normal Temperature Range. If SRT=1, then the DRAM will set an appropriate, potentially different, refresh rate to allow Self-Refresh operation in either the Normal or Extended Temperature Ranges. The value of the SRT bit can effect self-refresh power consumption, please refer to IDD table for details.
Self-Refresh mode summary
MR2
A[6]
MR2
A[7] Self-Refresh operation
Allowed Operating
Temperature Range
for Self-Refresh mode
0 0 Self-Refresh rate appropriate for the Normal Temperature Range Normal 1
(-40 ~ 85)
0 1
Self-Refresh appropriate for either the Normal or Extended Temperature Ranges.
The DRAM must support Extended Temperature Range. The value of the SRT bit
can effect self-refresh power consumption, please refer to the IDD table for details.
Normal and Extended 2
(-40 ~ 105)
1 0 ASR enabled (for devices supporting ASR and Normal Temperature Range).
Self-Refresh power consumption is temperature dependent. Normal
1 (-40 ~ 85)
1 0 ASR enabled (for devices supporting ASR and Extended Temperature Range).
Self-Refresh power consumption is temperature dependent.
Normal and Extended 2
(-40 ~ 105)
1 1 Illegal
ACTIVE Command
The ACTIVE command is used to open (or activate) a row in a particular bank for subsequent access. The value on the BA0-BA2 inputs selects the bank, and the addresses provided on inputs A0-A13 selects the row. These rows remain active (or open) for accesses until a precharge command is issued to that bank. A PRECHARGE command must be issued before opening a different row in the same bank.
PRECHARGE Command
The PRECHARGE command is used to deactivate the open row in a particular bank or the open row in all banks. The bank(s) will be available for a subsequent row activation a specified time (tRP) after the PRECHARGE command is issued, except in the case of concurrent auto precharge, where a READ or WRITE command to a different bank is allowed as long as it does not interrupt the data transfer in the current bank and does not violate any other timing parameters. Once a bank has been precharged, it is in the idle state and must be activated prior to any READ or WRITE commands being issued to that bank. A PRECHARGE command is allowed if there is no open row in that bank (idle bank) or if the previously open row is already in the process of precharging. However, the precharge period will be determined by the last PRECHARGE command issued to the bank.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 41/141
READ Operation
Read Burst Operation
During a READ or WRITE command DDR3(L) will support BC4 and BL8 on the fly using address A12 during the READ or WRITE (AUTO PRECHARGE can be enabled or disabled).
A12=0, BC4 (BC4 = burst chop, tCCD=4)
A12=1, BL8
A12 will be used only for burst length control, not a column address.
Read Burst Operation RL=5 (AL=0, CL=5, BL=8)
READ Burst Operation RL = 9 (AL=4, CL=5, BL=8)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 42/141
READ Timing Definitions
Read timing is shown in the following figure and is applied when the DLL is enabled and locked.
Rising data strobe edge parameters:
tDQSCK min/max describes the allowed range for a rising data strobe edge relative to CK, CK .
tDQSCK is the actual position of a rising strobe edge relative to CK, CK .
tQSH describes the DQS, DQS differential output high time.
tDQSQ describes the latest valid transition of the associated DQ pins.
tQH describes the earliest invalid transition of the associated DQ pins.
Falling data strobe edge parameters:
tQSL describes the DQS, DQS differential output low time.
tDQSQ describes the latest valid transition of the associated DQ pins.
tQH describes the earliest invalid transition of the associated DQ pins.
Read Timing Definition
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 43/141
Read Timing; Clock to Data Strobe relationship
Clock to Data Strobe relationship is shown in the following figure and is applied when the DLL is enabled and locked.
Rising data strobe edge parameters:
tDQSCK min/max describes the allowed range for a rising data strobe edge relative to CK and CK .
tDQSCK is the actual position of a rising strobe edge relative to CK and CK .
tQSH describes the data strobe high pulse width.
Falling data strobe edge parameters:
tQSL describes the data strobe low pulse width.
Clock to Data Strobe Relationship
Notes:
1. Within a burst, rising strobe edge is not necessarily fixed to be always at tDQSCK(min) or tDQSCK(max). Instead, rising strobe edge can vary between tDQSCK(min) and tDQSCK(max).
2. The DQS, DQS differential output high time is defined by tQSH and the DQS, DQS differential output low time is defined by
tQSL. 3. Likewise, tLZ(DQS)min and tHZ(DQS)min are not tied to tDQSCKmin (early strobe case) and tLZ(DQS)max and
tHZ(DQS)max are not tied to tDQSCKmax (late strobe case). 4. The minimum pulse width of read preamble is defined by tRPRE(min). 5. The maximum read postamble is bound by tDQSCK(min) plus tQSH(min) on the left side and tHZDSQ(max) on the right
side. 6. The minimum pulse width of read postamble is defined by tRPST(min). 7. The maximum read preamble is bound by tLZDQS(min) on the left side and tDQSCK(max) on the right side.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 44/141
Read Timing; Data Strobe to Data Relationship
The Data Strobe to Data relationship is shown in the following figure and is applied when the DLL and enabled and locked.
Rising data strobe edge parameters:
tDQSQ describes the latest valid transition of the associated DQ pins.
tQH describes the earliest invalid transition of the associated DQ pins.
Falling data strobe edge parameters:
tDQSQ describes the latest valid transition of the associated DQ pins.
tQH describes the earliest invalid transition of the associated DQ pins.
tDQSQ; both rising/falling edges of DQS, no tAC defined
Data Strobe to Data Relationship
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 45/141
Read to Read (CL=5, AL=0)
T11
T10
NOP
NOP
Dout
n +6
Dout
n +7
tRPS
T
CK CK
T0T1
T3T5
T6T7
T9T2
T4T8
NOP
CMD
NOP
NOP
READ
NOP
NOP
NOP
NOP
NOP
Addr
ess
Dout
n +1
Dout
n +2
Dout
n +3
Dout
n +4
Dout
n +5
tCCD
tRPR
E
Dout n
T12
NOP
T13
NOP
RL =
5
Bank
Col b
READ
Dout
b +6
Dout
b +7
Dout
b +1
Dout
b +2
Dout
b +3
Dout
b +4
Dout
b +5
Dout b
RL =
5
DQS,
DQS
DQ
REA
D (B
L8) t
o R
EAD
(BL8
)
NOP
NOP
tRPS
T
NOP
CMD
NOP
NOP
READ
NOP
NOP
NOP
NOP
NOP
Addr
ess
Dout
n +1
Dout
n +2
Dout
n +3
tCCD
tRPR
E
Dout n
NOP
NOP
RL =
5
Bank
Col b
READ
Dout
b +1
Dout
b +2
Dout
b +3
Dout b
RL =
5
DQS,
DQS
DQ
REA
D (B
L4) t
o RE
AD (B
L4)
tRPR
EtR
PST
READ
Bank
Col n
READ
Bank
Col n
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 46/141
READ to WRITE (CL=5, AL=0; CWL=5, AL=0)
T11
T10
NOP
Dout
n +6
Dout
n +7
tWPS
T
CK CK
T0T1
T3T5
T6T7
T9T2
T4T8
NOP
CMD
NOP
NOP
WRI
TE
Addre
ss
Dout
n +1
Dout
n +2
Dout
n +3
Dout
n +4
Dout
n +5
READ
to W
rite C
omma
nd de
lay =
RL +t
CCD
+ 2tC
K -W
LtRPR
E
Dout n
T12
NOP
T13
NOP
RL =
5
Bank
Col b
Dout
b +7
Dout
b +1
Dout
b +2
Dout
b +3
Dout
b +4
Dout
b +5
WL
= 5
DQS,
DQS
DQ
READ
(BL8
) to W
RITE
(BL8
)
NOP
tWPS
T
NOP
CMD
NOP
NOP
NOP
Addr
ess
Dout
n +1
Dout
n +2
Dout
n +3
READ
to W
RITE
Com
mand
Dela
y = R
L + t
CCD/
2 + 2t
CK - W
LtR
PRE
Dout n
NOP
NOP
RL =
5
READ
Dout
b +1
Dout
b +2
Dout
b +3
WL
= 5
DQS,
DQS
READ
(BL4
) to W
RITE
(BL4
)
tWPR
EtR
PST
T14
T15
NOP
NOP
tWRP
REtR
PST
Bank
Col n
READ
NOP
NOP
NOP
NOP
NOP
NOP
DQ
NOP
NOP
tBL
= 4 cl
ocks
tWR
tWTR
READ
Bank
Col n
WRI
TE
Bank
Col b
NOP
Dout b
NOP
NOP
NOP
NOP
Dout b
Dout
b +6
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 47/141
READ to READ (CL=5, AL=0)
T11
T10
NOP
NOP
Dout
n +6
Dout
n +7
tRPS
T
CK CK
T0T1
T3T5
T6T7
T9T2
T4T8
NOP
CMD
NOP
NOP
NOP
NOP
NOP
NOP
NOP
Addr
ess
Dout
n +1
Dout
n +2
Dout
n +3
Dout
n +4
Dout
n +5
tCCD
tRPR
E
Dout n
T12
NOP
T13
NOP
RL =
5
READ
Dout
b +1
Dout
b +2
Dout
b +3
Dout b
RL =
5
DQS,
DQS DQ
READ
(BL8
) to
READ
(BC4
)
NOP
NOP
tRPS
T
NOP
CMD
NOP
NOP
NOP
NOP
NOP
NOP
NOP
Addr
ess
Dout
n +1
Dout
n +2
Dout
n +3
tCCD
tRPR
E
Dout n
NOP
NOP
RL =
5
READ
RL =
5
DQS,
DQS
READ
(BC4
) to
READ
(BL8
)
tRPR
EtR
PST
DQ
READ
Bank
Col n
READ
Bank
Col n
READ
Bank
Col b
READ
Bank
Col b
Dout
b +6
Dout
b +7
Dout
b +1
Dout
b +2
Dout
b +3
Dout
b +4
Dout
b +5
Dout b
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 48/141
READ to WRITE (CL=5, AL=0; CWL=5, AL=0)
T11
T10
NOP
NOP
Dout
n +6
Dout
n +7
tRPS
T
CK CK
T0T1
T3T5
T6T7
T9T2
T4T8
NOP
CMD
NOP
NOP
WRI
TE
Addr
ess
Dout
n +1
Dout
n +2
Dout
n +3
Dout
n +4
Dout
n +5
tRPR
E
Dout n
T12
NOP
T13
NOP
RL =
5
READ
Dout
b +1
Dout
b +2
Dout
b +3
WL
= 5
DQS,
DQS DQ
NOP
NOP
tWPS
T
NOP
CMD
NOP
NOP
NOP
Addr
ess
Dout
n +1
Dout
n +2
Dout
n +3
READ
to W
RITE
Com
man
d de
lay =
RL
+ tC
CD/2
+2t
CK -
WL
tRPR
E
Dout n
NOP
NOP
RL =
5
READ
WL
= 5
DQS,
DQS
READ
(BL4
) to
WRI
TE (B
L8)
tWPR
EtR
PST
DQ
READ
Bank
Col n
READ
Bank
Col n
NOP
Bank
Col b
WRI
TE
Bank
Col b
Dout
b +6
Dout
b +7
Dout
b +1
Dout
b +2
Dout
b +3
Dout
b +4
Dout
b +5
Dout b
NOP
NOP
NOP
NOP
READ
(BL8
) to
WRI
TE (B
C4)
NOP
NOP
NOP
NOP
tWPS
TtW
PRE
Dout b
READ
to W
RITE
Com
man
d de
lay =
RL
+ tC
CD +
2tCK
- W
L
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 49/141
Write Operation
DDR3(L) Burst Operation
During a READ or WRITE command, DDR3(L) will support BC4 and BL8 on the fly using address A12 during the READ or
WRITE (Auto Precharge can be enabled or disabled).
A12=0, BC4 (BC4 = Burst Chop, tCCD=4)
A12=1, BL8
A12 is used only for burst length control, not as a column address.
WRITE Timing Violations
Motivation
Generally, if timing parameters are violated, a complete reset/initialization procedure has to be initiated to make sure the DRAM works properly. However, it is desirable for certain minor violations that the DRAM is guaranteed not to “hang up” and errors be limited to that particular operation.
For the following, it will be assumed that there are no timing violations with regard to the Write command itself (including ODT, etc.) and that it does satisfy all timing requirements not mentioned below.
Data Setup and Hold Violations
Should the strobe timing requirements (tDS, tDH) be violated, for any of the strobe edges associated with a write burst, then wrong data might be written to the memory location addressed with the offending WRITE command.
Subsequent reads from that location might result in unpredictable read data, however, the DRAM will work properly otherwise.
Strobe to Strobe and Strobe to Clock Violations
Should the strobe timing requirements (tDQSH, tDQSL, tWPRE, tWPST) or the strobe to clock timing requirements (tDSS, tDSH, tDQSS) be violated, for any of the strobe edges associated with a Write burst, then wrong data might be written to the memory location addressed with the offending WRITE command. Subsequent reads from that location might result in unpredictable read data, however the DRAM will work properly otherwise.
Write Timing Parameters
This drawing is for example only to enumerate the strobe edges that “belong” to a write burst. No actual timing violations are shown here. For a valid burst all timing parameters for each edge of a burst need to be satisfied (not only for one edge - as shown).
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 50/141
Write Timing Definition
Note:
1. BL=8, WL=5 (AL=0, CWL=5). 2. Din n = data in from column n. 3. NOP commands are shown for ease of illustration; other command may be valid at these times. 4. BL8 setting activated by either MR0 [A1:0=00] or MR0 [A1:0=01] and A12 = 1 during WRITE command at T0. 5. tDQSS must be met at each rising clock edge.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 51/141
WRITE to WRITE (WL=5; CWL=5, AL=0)
T11
T10
NOP
Dout
n +7
CK CK
T0T1
T3T5
T6T7
T9T2
T4T8
NOP
CMD
NOP
NOP
NOP
Addr
ess
Dout
n +1
Dout
n +2
Dout
n +3
Dout
n +5
tCCD
tWPR
E
T12
NOP
T13
NOP
WL
= 5
Dout
b +6
Dout
b +7
Dout
b +1
Dout
b +2
Dout
b +3
Dout
b +5
WL
= 5
DQS,
DQS DQ
WRI
TE (B
L8) t
o W
RITE
(BL8
)
NOP
tWPS
T
NOP
CMD
NOP
NOP
NOP
Addr
ess
Dout
n +1
Dout
n +2
Dout
n +3
tCCD
tRPR
E
NOP
NOP
WL
= 5
READ
Dout
b +1
Dout
b +2
Dout
b +3
WL
= 5
DQS,
DQS
WRI
TE (B
C4) t
o W
RITE
(BC4
)
tWPR
EtW
PST
tWPS
T
Bank
Col n
WRI
TENO
PNO
PNO
PNO
PNO
PW
RITE
DQ
WRI
TE
Bank
Col n
WRI
TE
Bank
Col b
NOP
Bank
Col b
Dout n
NOP
NOP
NOP
NOP
Dout
n +4
Dout
n +6
Dout b
Dout
b +4
tBL=
4
tWR
tWTR
tBL=
4
tWR
tWTR
Dout n
Dout b
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 52/141
WRITE to READ (RL=5, CL=5, AL=0; WL=5, CWL=5, AL=0; BL=4)
T11
T10
NOP
Dout
n +7
CK CK
T0T1
T3T5
T6T7
T9T2
T4T8
NOP
CMD
NOP
NOP
NOP
Addr
ess
Dout
n +1
Dout
n +2
Dout
n +3
Dout
n +5
tWPR
E
T12
NOP
T13
READ
WL
= 5
DQS,
DQS DQ
WRI
TE (B
L8) t
o RE
AD (B
C4/B
L8)
NOP
NOP
CMD
NOP
NOP
NOP
Addr
ess
Dout
n +1
Dout
n +2
Dout
n +3
tRPR
E
Dout n
NOP
READ
WL
= 5
DQS,
DQS
WR
ITE
(BC
4) to
REA
D (B
C4/B
L8)
tWPS
T
Bank
Col n
WRI
TENO
PNO
PNO
PNO
PNO
PNO
P
DQ
WRI
TE
Bank
Col n
NOP
NOP
Bank
Col b
Dout n
NOP
NOP
NOP
NOP
Dout
n +4
Dout
n +6
tWTR
RL=5
tBL=
4
tWPS
T
Bank
Col b
tWTR
RL=5
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 53/141
WRITE to WRITE (WL=5, CWL=5, AL=0)
T11
T10
NOP
Dout
n +7
CK CK
T0T1
T3T5
T6T7
T9T2
T4T8
NOP
CMD
NOP
NOP
NOP
Addr
ess
Dout
n +1
Dout
n +2
Dout
n +3
Dout
n +5
tCCD
tWPR
E
T12
NOP
T13
NOP
WL
= 5
Dout
b +1
Dout
b +2
WL
= 5
DQS,
DQS DQ
WRI
TE (B
L8) t
o W
RITE
(BC4
)
NOP
tWPS
T
NOP
CMD
NOP
NOP
NOP
Addr
ess
Dout
n +1
Dout
n +2
Dout
n +3
tCCD
tRPR
E
Dout n
NOP
NOP
WL
= 5
READ
Dout
b +1
Dout
b +2
Dout
b +3
WL
= 5
DQS,
DQS
WRI
TE (B
C4) t
o W
RITE
(BL8
)
tWPR
EtW
PST
tWPS
T
Bank
Col n
WRI
TENO
PNO
PNO
PNO
PNO
PW
RITE
DQ
WRI
TE
Bank
Col n
WRI
TE
Bank
Col b
NOP
Bank
Col b
Dout n
NOP
NOP
NOP
NOP
Dout
n +4
Dout
n +6
Dout b
tBL=
4
tWR
tWTR
tBL=
4
tWR
tWTR
Dout
b +3
Dout
b +6
Dout
b +7
Dout
b +3
Dout
b +5
Dout
b +4
Dout b
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 54/141
Refresh Command
The Refresh command (REF) is used during normal operation of the DDR3(L) SDRAMs. This command is not persistent, so it must be issued each time a refresh is required. The DDR3(L) SDRAM requires Refresh cycles at an average periodic interval of
tREFI. When CS , RAS and CAS are held Low and WE High at the rising edge of the clock, the chip enters a Refresh cycle.
All banks of the SDRAM must be precharged and idle for a minimum of the precharge time tRP(min) before the Refresh Command can be applied. The refresh addressing is generated by the internal refresh controller. This makes the address bits “Don’t Care” during a Refresh command. An internal address counter suppliers the address during the refresh cycle. No control of the external address bus is required once this cycle has started. When the refresh cycle has completed, all banks of the SDRAM will be in the precharged (idle) state. A delay between the Refresh Command and the next valid command, except NOP or DES, must be greater than or equal to the minimum Refresh cycle time tRFC(min) as shown in the following figure. In general, a Refresh command needs to be issued to the DDR3(L) SDRAM regularly every tREFI interval. To allow for improved efficiency in scheduling and switching between tasks, some flexibility in the absolute refresh interval is provided. A maximum of 8 Refresh commands can be postponed during operation of the DDR3(L) SDRAM, meaning that at no point in time more than a total of 8 Refresh commands are allowed to be postponed. In case that 8 Refresh commands are postponed in a row, the result-ing maximum interval between the surrounding Refresh commands is limited to 9 x tREFI. A maximum of 8 additional Refresh commands can be issued in advance (“pulled in”), with each one reducing the number of regular Refresh commands required later by one. Note that pulling in more than 8 Refresh commands in advance does not further reduce the number of regular Refresh commands required later, so that the resulting maximum interval between two surrounding Refresh command is limited to 9 x tREFI. Before entering Self-Refresh Mode, all postponed Refresh commands must be executed.
Self-Refresh Entry/Exit Timing
Postponing Refresh Commands (Example)
Pulled-in Refresh Commands (Example)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 55/141
Self-Refresh Operation
The Self-Refresh command can be used to retain data in the DDR3(L) SDRAM, even if the reset of the system is powered down. When in the Self-Refresh mode, the DDR3(L) SDRAM retains data without external clocking. The DDR3(L) SDRAM device has a
built-in timer to accommodate Self-Refresh operation. The Self-Refresh Entry (SRE) Command is defined by having CS , RAS ,
CAS and CKE held low with WE high at the rising edge of the clock.
Before issuing the Self-Refreshing-Entry command, the DDR3(L) SDRAM must be idle with all bank precharge state with tRP satisfied. Also, on-die termination must be turned off before issuing Self-Refresh-Entry command, by either registering ODT pin low “ODTL + 0.5tCK” prior to the Self-Refresh Entry command or using MRS to MR1 command. Once the Self-Refresh Entry command is registered, CKE must be held low to keep the device in Self-Refresh mode. During normal operation (DLL on), MR1 (A0=0), the DLL is automatically disabled upon entering Self-Refresh and is automatically enabled (including a DLL-RESET) upon exiting Self-Refresh.
When the DDR3(L) SDRAM has entered Self-Refresh mode, all of the external control signals, except CKE and RESET , are
“don’t care”. For proper Self-Refresh operation, all power supply and reference pins (VDD, VDDQ, VSS, VSSQ, VREFCA, and VREFDQ) must be at valid levels. The DRAM initiates a minimum of one Refresh command internally within tCKE period once it enters Self-Refresh mode. The clock is internally disabled during Self-Refresh operation to save power. The minimum time that the DDR3(L) SDRAM must remain in Self-Refresh mode is tCKE. The user may change the external clock frequency or halt the external clock tCKSRE after Self-Refresh entry is registered; however, the clock must be restarted and stable tCKSRX before the device can exit Self-Refresh mode. The procedure for exiting Self-Refresh requires a sequence of events. First, the clock must be stable prior to CKE going back HIGH. Once a Self-Refresh Exit Command (SRX, combination of CKE going high and either NOP or Deselect on command bus) is registered, a delay of at least tXS must be satisfied before a valid command not requiring a locked DLL can be issued to the device to allow for any internal refresh in progress. Before a command which requires a locked DLL can be applied, a delay of at least tXSDLL and applicable ZQCAL function requirements [TBD] must be satisfied. Before a command that requires a locked DLL can be applied, a delay of at least tXSDLL must be satisfied. Depending on the system environment and the amount of time spent in Self-Refresh, ZQ calibration commands may be required to compensate for the voltage and temperature drift as described in “ZQ Calibration Commands”. To issue ZQ calibration commands, applicable timing requirements must be satisfied. CKE must remain HIGH for the entire Self-Refresh exit period tXSDLL for proper operation except for Self-Refresh re-entry. Upon exit from Self-Refresh, the DDR3(L) SDRAM can be put back into Self-Refresh mode after waiting at least tXS period and issuing one refresh command (refresh period of tRFC). NOP or deselect commands must be registered on each positive clock edge during the Self-Refresh exit interval tXS. ODT must be turned off during tXSDLL. The use of Self-Refresh mode instructs the possibility that an internally times refresh event can be missed when CKE is raised for exit from Self-Refresh mode. Upon exit from Self-Refresh, the DDR3(L) SDRAM requires a minimum of one extra refresh com-mand before it is put back into Self-Refresh mode.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 56/141
Self-Refresh Entry/Exit Timing
Note:
1. Only NOP or DES commands 2. Valid commands not requiring a locked DLL 3. Valid commands requiring a locked DLL
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 57/141
Power-Down Modes
Power-Down Entry and Exit
Power-Down is synchronously entered when CKE is registered low (along with NOP or Deselect command). CKE is not allowed to go low while mode register set command, MPR operations, ZQCAL operations, DLL locking or read/write operation are in progress. CKE is allowed to go low while any of other operation such as row activation, precharge or auto precharge and refresh are in progress, but power-down IDD spec will not be applied until finishing those operation.
The DLL should be in a locked state when power-down is entered for fastest power-down exit timing. If the DLL is not locked during power-down entry, the DLL must be reset after exiting power-down mode for proper read operation and synchronous ODT operation. DRAM design provides all AC and DC timing and voltage specification as well proper DLL operation with any CKE intensive operations as long as DRAM controller complies with DRAM specifications.
During Power-Down, if all banks are closed after any in progress commands are completed, the device will be in precharge Power-Down mode; if any bank is open after in progress commands are completed, the device will be in active Power-Down mode.
Entering Power-down deactivates the input and output buffers, excluding CK, CK , ODT, CKE, and RESET . To protect DRAM
internal delay on CKE line to block the input signals, multiple NOP or Deselect commands are needed during the CKE switch off and cycle(s) after, this timing period are defined as tCPDED. CKE_low will result in deactivation of command and address receivers after tCPDED has expired.
Power-Down Entry Definitions
Status of DRAM MRS bit A12 DLL PD Exit Relevant Parameters
Active
(A Bank or more open) Don't Care On Fast tXP to any valid command.
Precharged
(All Banks Precharged) 0 Off Slow
tXP to any valid command. Since it is in precharge state,
commands here will be ACT, AR, MRS/EMRS, PR, or PRA.
tXPDLL to commands who need DLL to operate, such as RD,
RDA, or ODT control line.
Precharged
(All Banks Precharged) 1 On Fast tXP to any valid command.
Also the DLL is disabled upon entering precharge power-down (Slow Exit Mode), but the DLL is kept enabled during precharge
power-down (Fast Exit Mode) or active power-down. In power-down mode, CKE low, RESET high, and a stable clock signal
must be maintained at the inputs of the DDR3(L) SDRAM, and ODT should be in a valid state but all other input signals are “Don’t
care” (If RESET goes low during Power-Down, the DRAM will be out of PD mode and into reset state). CKE low must be
maintain until tCKE has been satisfied. Power-down duration is limited by 9 times tREFI of the device.
The power-down state is synchronously exited when CKE is registered high (along with a NOP or Deselect command). CKE high must be maintained until tCKE has been satisfied. A valid, executable command can be applied with power-down exit latency, tXP and/or tXPDLL after CKE goes high. Power-down exit latency is defined at AC spec table of this datasheet.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 58/141
Active Power-Down Entry and Exit timing diagram
Timing Diagrams for CKE with PD Entry, PD Exit with Read, READ with Auto Precharge, Write and Write with Auto Precharge,
Activate, Precharge, Refresh, MRS:
Power-Down Entry after Read and Read with Auto Precharge
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 59/141
Power-Down Entry after Write with Auto Precharge
Power-Down Entry after Write
Precharge Power-Down (Fast Exit Mode) Entry and Exit
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 60/141
Precharge Power-Down (Slow Exit Mode) Entry and Exit
Refresh Command to Power-Down Entry
Active Command to Power-Down Entry
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 61/141
Precharge/Precharge all Command to Power-Down Entry
MRS Command to Power-Down Entry
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 62/141
On-Die Termination (ODT)
ODT (On-Die Termination) is a feature of the DDR3(L) SDRAM that allows the DRAM to turn on/off termination resistance for
each DQ, DQS, DQS and DM via the ODT control pin. The ODT feature is designed to improve signal integrity of the memory
channel by allowing the DRAM controller to independently turn on/off termination resistance for any or all DRAM devices.
The ODT feature is turned off and not supported in Self-Refresh mode.
A simple functional representation of the DRAM ODT feature is shown as below.
Functional Representation of ODT
The switch is enabled by the internal ODT control logic, which uses the external ODT pin and other control information. The value of RTT is determined by the settings of Mode Register bits. The ODT pin will be ignored if the Mode Register MR1 and MR2 are programmed to disable ODT and in self-refresh mode.
ODT Mode Register and ODT Truth Table
The ODT Mode is enabled if either of MR1 A2, A6, A9 or MR2 A9, A10 are non-zero. In this case, the value of RTT is determined by the settings of those bits.
Application: Controller sends WR command together with ODT asserted. One possible application: The rank that is being written to provides termination. DRAM turns ON termination if it sees ODT asserted (except ODT is disabled by MR) DRAM does not use any write or read command decode information.
Termination Truth Table
ODT pin DRAM Termination State
0 OFF
1 ON, (OFF, if disabled by MR1 A2, A6, A9 and MR2A9, A10 in general)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 63/141
Synchronous ODT Mode
Synchronous ODT mode is selected whenever the DLL is turned on and locked. Based on the power-down definition, these modes are:
Any bank active with CKE high
Refresh with CKE high
Idle mode with CKE high
Active power down mode (regardless of MR0 bit A12)
Precharge power down mode if DLL is enabled during precharge power down by MR0 bit A12
The direct ODT feature is not supported during DLL-off mode. The on-die termination resistors must be disabled by continuously registering the ODT pin low and/or by programming the RTT_Nom bits MR1A9,A6,A2 to 0,0,0 via a mode register set command during DLL-off mode.
In synchronous ODT mode, RTT will be turned on ODTLon clock cycles after ODT is sampled high by a rising clock edge and turned off ODTLoff clock cycles after ODT is registered low by a rising clock edge. The ODT latency is tied to the write latency (WL) by: ODTLonn = WL - 2; ODTLoff = WL-2.
ODT Latency and Posted ODT
In synchronous ODT Mode, the Additive Latency (AL) programmed into the Mode Register (MR1) also applies to the ODT signal. The DRAM internal ODT signal is delayed for a number of clock cycles defined by the Additive Latency (AL) relative to the external ODT signal. ODTLon = CWL + AL - 2; ODTLoff = CWL + AL - 2. For details, refer to DDR3(L) SDRAM latency definitions.
ODT Latency
Symbol Parameter DDR3(L)-1600 Unit
ODTLon ODT turn on Latency WL - 2 = CWL + AL - 2 tCK
ODTLoff ODT turn off Latency WL - 2 = CWL + AL - 2 tCK
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 64/141
Timing Parameters
In synchronous ODT mode, the following timing parameters apply: ODTLon, ODTLoff, tAON min/max, tAOF min/max.
Minimum RTT turn-on time (tAON min) is the point in time when the device leaves high impedance and ODT resistance begins to turn on. Maximum RTT turn-on time (tAON max) is the point in time when the ODT resistance is fully on. Both are measured from ODTLon.
Minimum RTT turn-off time (tAOF min) is the point in time when the device starts to turn off the ODT resistance. Maximum RTT turn off time (tAOF max) is the point in time when the on-die termination has reached high impedance. Both are measured from ODTLoff.
When ODT is asserted, it must remain high until ODTH4 is satisfied. If a Write command is registered by the SDRAM with ODT high, then ODT must remain high until ODTH4 (BL=4) or ODTH8 (BL=8) after the write command. ODTH4 and ODTH8 are measured from ODT registered high to ODT registered low or from the registration of a write command until ODT is registered low.
Synchronous ODT Timing Example for AL=3; CWL=5; ODTLon=AL+CWL-2=6; ODTLoff=AL+CWL-2=6
Synchronous ODT example with BL=4, WL=7
ODT must be held for at least ODTH4 after assertion (T1); ODT must be kept high ODTH4 (BL=4) or ODTH8 (BL=8) after Write command (T7). ODTH is measured from ODT first registered high to ODT first registered low, or from registration of Write command with ODT high to ODT registered low. Note that although ODTH4 is satisfied from ODT registered at T6 ODT must not go low before T11 as ODTH4 must also be satisfied from the registration of the Write command at T7.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 65/141
ODT during Reads:
As the DDR3(L) SDRAM cannot terminate and drive at the same time, RTT must be disabled at least half a clock cycle before the read preamble by driving the ODT pin low appropriately. RTT may not be enabled until the end of the post-amble as shown in the following figure. DRAM turns on the termination when it stops driving which is determined by tHZ. If DRAM stops driving early (i.e. tHZ is early), then tAONmin time may apply. If DRAM stops driving late (i.e. tHZ is late), then DRAM complies with tAONmax timing. Note that ODT may be disabled earlier before the Read and enabled later after the Read than shown in this example.
ODT must be disabled externally during Reads by driving ODT low. (Example: CL=6; AL=CL-1=5;
RL=AL+CL=11; CWL=5; ODTLon=CWL+AL-2=8; ODTLoff=CWL+AL-2=8)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 66/141
Dynamic ODT
In certain application cases and to further enhance signal integrity on the data bus, it is desirable that the termination strength of the DDR3(L) SDRAM can be changed without issuing an MRS command. This requirement is supported by the “Dynamic ODT” feature as described as follows:
Functional Description
The Dynamic ODT Mode is enabled if bit (A9) or (A10) of MR2 is set to ‘1’. The function is described as follows:
Two RTT values are available: RTT_Nom and RTT_WR.
The value for RTT_Nom is preselected via bits A[9,6,2] in MR1.
The value for RTT_WR is preselected via bits A[10,9] in MR2.
During operation without write commands, the termination is controlled as follows:
Nominal termination strength RTT_Nom is selected.
Termination on/off timing is controlled via ODT pin and latencies ODTLon and ODTLoff.
When a Write command (WR, WRA, WRS4, WRS8, WRAS4, WRAS8) is registered, and if Dynamic ODT is enabled, the termi-nation is controlled as follows:
A latency ODTLcnw after the write command, termination strength RTT_WR is selected.
A latency ODTLcwn8 (for BL8, fixed by MRS or selected OTF) or ODTLcwn4 (for BC4, fixed by MRS or selected OTF)
after the write command, termination strength RTT_Nom is selected.
Termination on/off timing is controlled via ODT pin and ODTLon, ODTLoff.
The following table shows latencies and timing parameters which are relevant for the on-die termination control in Dynamic ODT mode.
The dynamic ODT feature is not supported at DLL-off mode. User must use MRS command to set RTT_WR, MR2[A10,A9 = [0,0], to disable Dynamic ODT externally.
When ODT is asserted, it must remain high until ODTH4 is satisfied. If a Write command is registered by the SDRAM with ODT high, then ODT must remain high until ODTH4 (BL=4) or ODTH8 (BL=8) after the Write command. ODTH4 and ODTH8 are measured from ODT registered high to ODT registered low or from the registration of Write command until ODT is register low.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 67/141
Latencies and timing parameters relevant for Dynamic ODT
Name and Description Abbr. Defined from Defined to Definition for all
DDR3(L) speed pin Unit
ODT turn-on Latency ODTLon Registering external ODT signal high
turning termination on ODTLon=WL-2 tCK
ODT turn-off Latency ODTLoff registering external ODT signal low
turning termination off ODTLoff=WL-2 tCK
ODT Latency for changing from RTT_Nom to RTT_WR
ODTLcnw registering external write command
change RTT strength from RTT_Nom to RTT_WR
ODTLcnw=WL-2 tCK
ODT Latency for change from RTT_WR to RTT_Nom (BL=4)
ODTLcwn4 registering external write command
change RTT strength from RTT_WR to RTT_Nom
ODTLcwn4=4+ODTLoff tCK
ODT Latency for change from RTT_WR to RTT_Nom (BL=8)
ODTLcwn8 registering external write command
change RTT strength from RTT_WR to RTT_Nom
ODTLcwn8=6+ODTLoff tCK(avg)
Minimum ODT high time after ODT assertion
ODTH4 registering ODT high ODT registered low ODTH4=4 tCK(avg)
Minimum ODT high time after Write (BL=4)
ODTH4 registering write with ODT high
ODT registered low ODTH4=4 tCK(avg)
Minimum ODT high time after Write (BL=8)
ODTH8 registering write with ODT high
ODT register low ODTH8=6 tCK(avg)
RTT change skew tADC ODTLcnw ODTLcwn
RTT valid tADC(min)=0.3tCK(avg) tADC(max)=0.7tCK(avg)
tCK(avg)
Note: tAOF,nom and tADC,nom are 0.5tCK (effectively adding half a clock cycle to ODTLoff, ODTcnw, and ODTLcwn)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 68/141
ODT Timing Diagrams
Dynamic ODT: Behavior with ODT being asserted before and after the write
Note: Example for BC4 (via MRS or OTF), AL=0, CWL=5. ODTH4 applies to first registering ODT high and to the registration of
the Write command. In this example ODTH4 would be satisfied if ODT went low at T8. (4 clocks after the Write command).
Dynamic ODT: Behavior without write command, AL=0, CWL=5
Note: ODTH4 is defined from ODT registered high to ODT registered low, so in this example ODTH4 is satisfied; ODT registered
low at T5 would also be legal.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 69/141
Dynamic ODT: Behavior with ODT pin being asserted together with write command for the duration of 6
Clock cycles
Note: Example for BL8 (via MRS or OTF), AL=0, CWL=5. In this example ODTH8=6 is exactly satisfied.
Dynamic ODT: Behavior with ODT pin being asserted together with write command for a duration of 6 clock
cycles, example for BC4 (via MRS or OTF), AL=0, CWL=5
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 70/141
Dynamic ODT: Behavior with ODT pin being asserted together with write command for the duration of 4
Clock cycles
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 71/141
Asynchronous ODT Mode
Asynchronous ODT mode is selected when DRAM runs in DLLon mode, but DLL is temporarily disabled (i.e. frozen) in precharge
power-down (by MR0 bit A12). Based on the power down mode definitions, this is currently Precharge power down mode if DLL
is disabled during precharge power down by MR0 bit A12.
In asynchronous ODT timing mode, internal ODT command is NOT delayed by Additive Latency (AL) relative to the external ODT
command.
In asynchronous ODT mode, the following timing parameters apply: tAONPD min/max, tAOFPD min/max.
Minimum RTT turn-on time (tAONPD min) is the point in time when the device termination circuit leaves high impedance state
and ODT resistance begins to turn on. Maximum RTT turn on time (tAONPD max) is the point in time when the ODT resistance is
fully on.
tAONPD min and tAONPDmax are measured from ODT being sampled high.
Minimum RTT turn-off time (tAOFPDmin) is the point in time when the devices termination circuit starts to turn off the ODT
resistance. Maximum ODT turn off time (tAOFPDmax) is the point in time when the on-die termination has reached high
impedance. tAOFPD min and tAOFPDmax are measured from ODT being sample low.
Asynchronous ODT Timings on DDR3(L) SDRAM with fast ODT transition: AL is ignored.
In Precharge Power Down, ODT receiver remains active; however no Read or Write command can be issued, as the respective
ADD/CMD receivers may be disabled.
Asynchronous ODT Timing Parameters for all Speed Bins
Symbol Description Min. Max. Unit
tAONPD Asynchronous RTT turn-on delay (Power-Down with DLL frozen) 2 8.5 ns
tAOFPD Asynchronous RTT turn-off delay (Power-Down with DLL frozen) 2 8.5 ns
ODT timing parameters for Power Down (with DLL frozen) entry and exit transition period
Description Min. Max.
ODT to RTT
turn-on delay
min ODTLon * tCK + tAONmin; tAONPDmin
min (WL - 2) * tCK + tAONmin; tAONPDmin
max ODTLon * tCK + tAONmax; tAONPDmax
max (WL - 2) * tCK + tAONmax; tAONPFmax
ODT to RTT
turn-off delay
min ODTLoff * tCK + tAOFmin; tAOFPDmin
min (WL - 2) * tCK + tAOFmin; tAOFPDmin
max ODTLoff * tCK + tAOFmax; tAOFPDmax
max (WL - 2) * tCK + tAOFmax; tAOFPDmax
tANPD WL-1
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 72/141
Synchronous to Asynchronous ODT Mode Transition during Power-Down Entry
If DLL is selected to be frozen in Precharge Power Down Mode by the setting of bit A12 in MR0 to “0”, there is a transition period around power down entry, where the DDR3(L) SDRAM may show either synchronous or asynchronous ODT behavior.
The transition period is defined by the parameters tANPD and tCPDED(min). tANPD is equal to (WL-1) and is counted back-wards in time from the clock cycle where CKE is first registered low. tCPDED(min) starts with the clock cycle where CKE is first registered low. The transition period begins with the starting point of tANPD and terminates at the end point of tCPDED(min). If there is a Refresh command in progress while CKE goes low, then the transition period ends at the later one of tRFC(min) after the Refresh command and the end point of tCPDED(min). Please note that the actual starting point at tANPD is excluded from the transition period, and the actual end point at tCPDED(min) and tRFC(min, respectively, are included in the transition period.
ODT assertion during the transition period may result in an RTT changes as early as the smaller of tAONPDmin and (ODT-Lon*tCK+tAONmin) and as late as the larger of tAONPDmax and (ODTLon*tCK+tAONmax). ODT de-assertion during the transition period may result in an RTT change as early as the smaller of tAOFPDmin and (ODTLoff*tCK+tAOFmin) and as late as the larger of tAOFPDmax and (ODTLoff*tCK+tAOFmax). Note that, if AL has a large value, the range where RTT is uncertain becomes quite large. The following figure shows the three different cases: ODT_A, synchronous behavior before tANPD; ODT_B has a state change during the transition period; ODT_C shows a state change after the transition period.
Synchronous to asynchronous transition during Precharge Power Down (with DLL frozen) entry (AL=0;
CWL=5; tANPD=WL-1=4)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 73/141
Asynchronous to Synchronous ODT Mode transition during Power-Down Exit
If DLL is selected to be frozen in Precharge Power Down Mode by the setting of bit A12 in MR0 to “0”, there is also a transition period around power down exit, where either synchronous or asynchronous response to a change in ODT must be expected from the DDR3(L) SDRAM.
This transition period starts tANPD before CKE is first registered high, and ends tXPDLL after CKE is first registered high. tANPD is equal to (WL -1) and is counted (backwards) from the clock cycle where CKE is first registered high.
ODT assertion during the transition period may result in an RTT change as early as the smaller of tAONPDmin and (ODT-Lon*tCK+tAONmin) and as late as the larger of tAONPDmax and (ODTLon*tCK+tAONmax). ODT de-assertion during the transition period may result in an RTT change as early as the smaller of tAOFPDmin and (ODTLoff*tCK+tAOFmin) and as late as the larger of tAOFPDmax and (ODToff*tCK+tAOFmax). Note that if AL has a large value, the range where RTT is uncertain becomes quite large. The following figure shows the three different cases: ODT_C, asynchronous response before tANPD; ODT_B has a state change of ODT during the transition period; ODT_A shows a state change of ODT after the transition period with synchronous response.
Asynchronous to synchronous transition during Precharge Power Down (with DLL frozen) exit (CL=6;
AL=CL-1; CWL=5; tANPD=WL-1=9)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 74/141
Asynchronous to Synchronous ODT Mode during short CKE high and short CKE low
periods
If the total time in Precharge Power Down state or Idle state is very short, the transition periods for PD entry and PD exit may overlap. In this case, the response of the DDR3(L) SDRAMs RTT to a change in ODT state at the input may be synchronous or asynchronous from the state of the PD entry transition period to the end of the PD exit transition period (even if the entry ends later than the exit period).
If the total time in Idle state is very short, the transition periods for PD exit and PD entry may overlap. In this case, the response of the DDR3(L) SDRAMs RTT to a change in ODT state at the input may be synchronous or asynchronous from the state of the PD exit transition period to the end of the PD entry transition period. Note that in the following figure, it is assumed that there was no Refresh command in progress when Idle state was entered.
Transition period for short CKE cycles with entry and exit period overlapping (AL=0; WL=5;
tANPD=WL-1=4)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 75/141
ZQ Calibration Commands
ZQ Calibration Description
ZQ Calibration command is used to calibrate DRAM Ron and ODT values. DDR3(L) SDRAM needs longer time to calibrate output driver and on-die termination circuits at initialization and relatively smaller time to perform periodic calibrations.
ZQCL command is used to perform the initial calibration during power-up initialization sequence. This command may be issued at any time by the controller depending on the system environment. ZQCL command triggers the calibration engine inside the DRAM and once calibration is achieved the calibrated values are transferred from calibration engine to DRAM IO which gets reflected as updated output driver and on-die termination values.
The first ZQCL command issued after reset is allowed a timing period of tZQinit to perform the full calibration and the transfer of values. All other ZQCL commands except the first ZQCL command issued after RESET is allowed a timing period of tZQoper.
ZQCS command is used to perform periodic calibrations to account for voltage and temperature variations. A shorter timing win-dow is provided to perform the calibration and transfer of values as defined by timing parameter tZQCS.
No other activities should be performed on the DRAM channel by the controller for the duration of tZQinit, tZQoper, or tZQCS. The quiet time on the DRAM channel allows calibration of output driver and on-die termination values. Once DRAM calibration is achieved, the DRAM should disable ZQ current consumption path to reduce power.
All banks must be precharged and tRP met before ZQCL or ZQCS commands are issued by the controller.
ZQ calibration commands can also be issued in parallel to DLL lock time when coming out of self refresh. Upon self-refresh exit, DDR3(L) SDRAM will not perform an IO calibration without an explicit ZQ calibration command. The earliest possible time for ZQ Calibration command (short or long) after self refresh exit is tXS.
In systems that share the ZQ resistor between devices, the controller must not allow any overlap of tZQoper, tZQinit, or tZQCS between ranks.
ZQ Calibration Timing
Note:
1. CKE must be continuously registered high during the calibration procedure. 2. On-die termination must be disabled via the ODT signal or MRS during the calibration procedure. 3. All devices connected to the DQ bus should be high impedance during the calibration procedure.
ZQ External Resistor Value, Tolerance, and Capacitive loading
In order to use the ZQ calibration function, a 240 ohm +/- 1% tolerance external resistor connected between the ZQ pin and ground. The single resistor can be used for each SDRAM or one resistor can be shared between two SDRAMs if the ZQ calibration timings for each SDRAM do not overlap. The total capacitive loading on the ZQ pin must be limited.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 76/141
Absolute Maximum Ratings
Absolute Maximum DC Ratings
Symbol Parameter Rating Unit Note
VDD Voltage on VDD pin relative to Vss -0.4 ~ 1.80 V 1,3
VDDQ Voltage on VDDQ pin relative to Vss -0.4 ~ 1.80 V 1,3
Vin, Vout Voltage on any pin relative to Vss -0.4 ~ 1.80 V 1
Tstg Storage Temperature -55 ~ 100 C 1,2
Note:
1. Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device.This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
2. Storage Temperature is the case surface temperature on the center/top side of the DRAM. 3. VDD and VDDQ must be within 300mV of each other at all times; and VREF must be not greater than 0.6VDDQ,
when VDD and VDDQ are less than 500mV; VREF may be equal to or less than 300mV.
Refresh parameters
Parameter Symbol Value Unit
REF command to ACT or REF command time tRFC 160 ns
Temperature Range
Parameter Value Units Notes
Normal Operating Temperature Range -40~+85 °C 1
Extended Temperature Range +85~+105 °C 1,2
Note:
1. Operating Temperature Toper is the case surface temperature on the center/top side of the DRAM.
2. Some applications require operation of the DRAM in the Extended Temperature Range. a) Refresh commands must be doubled in frequency, therefore, reducing the Refresh interval tREFI to 3.9us. b) If Self-Refresh operation is required in the Extended Temperature Range, then it is mandatory to either use the
Manual Self-Refresh mode with Extended Temperature Range capability (MR2 A6=0 and MR2 A7=1) or enable the optional Auto Self-Refresh mode (MR2 A6=1 and MR2 A7=0).
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 77/141
AC & DC Operating Conditions
Recommended DC Operating Conditions
DDR3
Symbol Parameter Rating
Unit Note Min. Typ. Max.
VDD Supply Voltage 1.425 1.5 1.575 V 1,2
VDDQ Supply Voltage for Output 1.425 1.5 1.575 V 1,2
DDR3L
Symbol Parameter Rating
Unit Note Min. Typ. Max.
VDD Supply Voltage 1.283 1.35 1.45 V 3,4,5
VDDQ Supply Voltage for Output 1.283 1.35 1.45 V 3,4,5
Note:
1. Under all conditions VDDQ must be less than or equal to VDD.
2. VDDQ tracks with VDD. AC parameters are measured with VDD and VDDQ tied together.
3. Maximum DC value may not be greater than 1.425V. The DC value is the linear average of VDD/VDDQ(t) over a very long
period of time.
4. If maximum limit is exceeded, input levels shall be governed by DDR3 specifications.
5. Under these supply voltages, the device operates to this DDR3L specifcation.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 78/141
AC & DC Input Measurement Levels
AC and DC Logic Input Levels for Command and Address (DDR3-1600/ 1866)
Symbol Parameter DDR3-1600 DDR3-1866
Unit Note Min. Max. Min. Max.
VIH.CA(DC100) DC input logic high VREF + 0.1 VDD VREF + 0.1 VDD V 1,5
VIL.CA(DC100) DC input logic low VSS VREF - 0.1 VSS VREF - 0.1 V 1,6
VIH.CA(AC175) AC input logic high VREF + 0.175 Note2 - - V 1,2,7
VIL.CA(AC175) AC input logic low Note2 VREF - 0.175 - - V 1,2,8
VIH.CA(AC150) AC input logic high VREF + 0.150 Note2 - - V 1,2,7
VIL.CA(AC150) AC input logic low Note2 VREF - 0.150 - - V 1,2,8
VIH.CA(AC135) AC input logic high - - VREF + 0.135 Note2 V 1,2,7
VIL.CA(AC135) AC input logic low - - Note2 VREF - 0.135 V 1,2,8
VIH.CA(AC125) AC input logic high - - VREF + 0.125 Note2 V 1,2,7
VIL.CA(AC125) AC input logic low - - Note2 VREF - 0.125 V 1,2,8
VREFCA(DC) Reference Voltage for ADD, CMD inputs
0.49 * VDD 0.51 * VDD 0.49 * VDD 0.51 * VDD V 3,4,9
Note:
1. For input only pins except
2. See “Overshoot and Undershoot Specifications” .
3. The ac peak noise on VRef may not allow VRef to deviate from VRefCA(DC) by more than +/-1% VDD (for reference: approx. +/-
15 mV).
4. For reference: approx. VDD/2 +/- 15 mV.
5. VIH(dc) is used as a simplified symbol for VIH.CA(DC100)
6. VIL(dc) is used as a simplified symbol for VIL.CA(DC100)
7. VIH(ac) is used as a simplified symbol for VIH.CA(AC175), VIH.CA(AC150), VIH.CA(AC135), and VIH.CA(AC125);
VIH.CA(AC175) value is used when Vref + 0.175V is referenced, VIH.CA(AC150) value is used when Vref + 0.150V is referenced,
VIH.CA(AC135) value is used when Vref + 0.135V is referenced, and VIH.CA(AC125) value is used when Vref + 0.125V is
referenced.
8. VIL(ac) is used as a simplified symbol for VIL.CA(AC175), VIL.CA(AC150), VIL.CA(AC135) and VIL.CA(AC125); VIL.CA(AC175)
value is used when Vref - 0.175V is referenced, VIL.CA(AC150) value is used when Vref - 0.150V is referenced, VIL.CA(AC135)
value is used when Vref - 0.135V is referenced, and VIL.CA(AC125) value is used when Vref - 0.125V is referenced.
9. VrefCA(DC) is measured relative to VDD at the same point in time on the same device
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 79/141
AC and DC Logic Input Levels for Command and Address (DDR3(L)-1600/ 1866)
Symbol Parameter DDR3L-1600 DDR3L-1866
Unit Note Min. Min. Min. Max.
VIH.CA(DC90) DC input logic high VREF + 0.09 VDD VREF+0.09 VDD V 1
VIL.CA(DC90) DC input logic low VSS VREF - 0.09 VSS VREF-0.09 V 1
VIH.CA(AC160) AC input logic high VREF + 0.16 Note2 - - V 1,2
VIL.CA(AC160) AC input logic low Note2 VREF - 0.16 - - V 1,2
VIH.CA(AC135) AC input logic high VREF+0.135 Note2 VREF+0.135 Note2 V 1,2
VIL.CA(AC135) AC input logic low Note2 VREF-0.135 Note2 VREF - 0.135 V 1,2
VIH.CA(AC125) AC input logic high - - VREF + 0.125 Note2 V 1,2
VIL.CA(AC125) AC input logic low - - Note2 VREF - 0.125 V 1,2
VREFCA(DC) Reference Voltage for ADD, CMD inputs 0.49 * VDD 0.49 * VDD 0.49 * VDD 0.51 * VDD V 3,4
Note:
1 For input only pins except RE
2 See “Overshoot and Undershoot Specifications”
3 The AC peak noise on VRef may not allow VRef to deviate from VRefDQ(DC) by more than +/-1% VDD (for reference: approx. +/-
13.5 mV).
4 For reference: approx. VDD/2 +/- 13.5 mV
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 80/141
AC and DC Logic Input Levels for DQ and DM (DDR3-1600/ 1866)
Symbol Parameter DDR3-1600 DDR3-1866
Unit Note Min. Max. Min. Max.
VIH.DQ(DC100) DC input logic high VREF + 0.1 VDD VREF + 0.1 VDD V 1,5
VIL.DQ(DC100) DC input logic low VSS VREF- 0.1 VSS VREF- 0.1 V 1,6
VIH.DQ(AC150) AC input logic high VREF + 0.150 Note2 - - V 1,2,7
VIL.DQ(AC150) AC input logic low Note2 VREF - 0.150 - - V 1,2,8
VIH.DQ(AC135) AC input logic high VREF + 0.135 Note2 VREF + 0.135 Note2 V 1,2,7
VIL.DQ(AC135) AC input logic low Note2 VREF - 0.135 Note2 VREF - 0.135 V 1,2,8
VREFDQ(DC) Reference Voltage for DQ, DM inputs
0.49 * VDD 0.51 * VDD 0.49 * VDD 0.51 * VDD V 3,4,9
Note:
1. VREF = VREFDQ(DC). 2. See "Overshoot and Undershoot Specifications". 3. The ac peak noise on VREF may not allow VREF to deviate from VREFDQ(DC) by more than +/-1% VDD (for
reference: approx. +/- 15 mV). 4. For reference: approx. VDD/2 +/- 15 mV. 5. VIH(dc) is used as a simplified symbol for VIH.DQ(DC100). 6. VIL(dc) is used as a simplified symbol for VIL.DQ(DC100). 7. VIH(ac) is used as a simplified symbol for VIH.DQ(AC175), VIH.DQ(AC150), and VIH.DQ(AC135);VIH.DQ(AC175)
value is used when VREF + 0.175V is referenced, VIH.DQ(AC150) value is used when VREF + 0.150V is referenced, and VIH.DQ(AC135) value is used when VREF + 0.135V is referenced.
8. VIL(ac) is used as a simplified symbol for VIL.DQ(AC175), VIL.DQ(AC150), and VIL.DQ(AC135);VIL.DQ(AC175) value is used when VREF - 0.175V is referenced, VIL.DQ(AC150) value is used when VREF -0.150V is referenced, and VIL.DQ(AC135) value is used when VREF - 0.135V is referenced.
9. VREFCA(DC) is measured relative to VDD at the same point in time on the same device
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 81/141
AC and DC Logic Input Levels for DQ and DM (DDR3(L)-1600/ 1866)
Symbol Parameter DDR3L-1600 DDR3L-1866
Unit Note Min. Min. Min. Max.
VIH.DQ(DC90) DC input logic high VREF + 0.09 VDD VREF + 0.09 VDD V 1
VIL.DQ(DC90) DC input logic low VSS VREF - 0.09 VSS VREF - 0.09 V 1
VIH.DQ(AC160) AC input logic high VREF + 0.16 Note 2 V 1,2
VIL.DQ(AC160) AC input logic low Note 2 VREF - 0.16 V 1,2
VIH.DQ(AC135) AC input logic high VREF + 0.135 Note 2 VREF + 0.135 Note 2 V 1,2
VIL.DQ(AC135) AC input logic low Note2 VREF - 0.135 Note2 VREF - 0.135 V 1,2
VIH.DQ(AC130) AC input logic high VREF + 0.130 Note2 V 1,2
VIL.DQ(AC130) AC input logic low Note2 VREF - 0.130 V 1,2
VREFDQ(DC) Reference Voltage for DQ, DM inputs
0.49 * VDD 0.51 * VDD 0.49 * VDD 0.51 * VDD V 3,4
Note:
1. For input only pins except RE
2. See “Overshoot and Undershoot Specifications”.
3. The AC peak noise on VRef may not allow VRef to deviate from VRefDQ(DC) by more than +/-1% VDD (for
reference: approx. +/- 13.5 mV).
4. For reference: approx. VDD/2 +/- 13.5 mV.
5. These levels apply for 1.35 Volt (see Table 5) operation only. If the device is operated at 1.5 V (see Table 24), the
respective levels in JESD79-3
(VIH/L.DQ(DC100), VIH/L.DQ(AC175), VIH/L.DQ(AC150), VIH/L.DQ(AC135), etc. ) apply. The 1.5 V levels
(VIH/L.DQ(DC100), VIH/L.DQ(AC175),
VIH/L.DQ(AC150), VIH/L.DQ(AC135), etc. ) do not apply when the device is operated in the 1.35 voltage range.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 82/141
VREF Tolerances
The dc-tolerance limits and ac-moist limits for the reference voltages VREFCA and VREFDQ are illustrated in the following figure. It shows a valid reference voltage VREF (t) as a function of time. (VREF stands for VREFCA and VREFDQ likewise).
VREF(DC) is the linear average of VREF(t) over a very long period of time (e.g.,1 sec). This average has to meet the min/max requirement in previous page. Furthermore VREF(t) may temporarily deviate from VREF(DC) by no more than ±1% VDD.
The voltage levels for setup and hold time measurements VIH(AC), VIH(DC), VIL(AC), and VIL(DC) are dependent on VREF.
“VREF” shall be understood as VREF(DC).
The clarifies that dc-variations of VREF affect the absolute voltage a signal has to reach to achieve a valid high or low level and therefore the time to which setup and hold is measured. System timing and voltage budgets need to account for VREF(DC) deviations from the optimum position within the data-eye of the input signals.
This also clarifies that the DRAM setup/hold specification and de-rating values need to include time and voltage associated with VREF ac-noise. Timing and voltage effects due to ac-noise on VREF up to the specified limit (±1% of VDD) are included in DRAM
timing and their associated de-ratings.
Illustration of VREF(DC) tolerance and VREF ac-noise limits
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 83/141
Differential AC and DC Logic Input Levels for clock (CK- CK ) and Strobe (DQS -DQS )
Symbol Parameter DDR3-1600/ 1866 DDR3L-1600/ 1866
Unit Notes Min. Max. Min. Max.
VIHdiff Differential input logic high +02.00 Note3 +0.180 Note3 V 1
VILdiff Differential input logic low Note3 -0.200 Note3 -0.180 V 1
VIHdiff(ac) Differential input high ac 2 x ( VIH(ac) –
VREF ) Note3
2 x
( VIH(ac) –
VREF )
Note3 V 2
VILdiff(ac) Differential input low ac Note3 2 x ( VIL(ac)-
VREF ) Note3
2 x
( VIL(ac)-
VREF )
V 2
Note:
1. Used to define a differential signal slew-rate.
2. For CK - CK use VIH/VIL(ac) of ADD/CMD and VREFCA; for DQS - DQS , DQSL, DQSL , DQSU,DQSU
use VIH/VIL(ac) of DQs and VREFDQ; if a reduced ac-high or ac-low level is used for a signal group, then
the reduced level applies also there.
3. These values are not defined, however the single-ended signals CK, CK ,
DQS, DQS ,DQSL, DQSL ,DQSU, DQSU need to be within the respective limits (VIH(dc)max, VIL(dc)min)
for single-ended signals as well as limitations for overshoot and undershoot. Refer to ”Overshoot and
Undershoot Specifications”.
Definition of differential ac-swing and “time above ac-level”
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 84/141
Allowed time before ringback (tDVAC) for CK - CK and DQS -DQS
Slew Rate
[V/ns]
DDR3-1600 DDR3L-1866
tDVAC [ps] @ IVIH/Ldiff(ac)I =
350mV
tDVAC [ps] @ IVIH/Ldiff(ac)I =
300mV
tDVAC [ps] @ IVIH/Ldiff(ac)I =
(DQS- DQS ) only
tDVAC [ps] @ IVIH/Ldiff(ac)I =
300mV
tDVAC [ps] @ IVIH/Ldiff(ac)I =
(CK- CK )only
Min. Max. Min. Max. Min. Max. Min. Max. Min. Max.
> 4.0 75 - 175 - 214 - 134 - 139 -
4.0 57 - 170 - 214 - 134 - 139 -
3.0 50 - 167 - 191 - 112 - 118 -
2.0 38 - 119 - 146 - 67 - 77 -
1.8 34 - 102 - 131 - 52 - 63 -
1.6 29 - 81 - 113 - 33 - 45 -
1.4 22 - 54 - 88 - 9 - 23 -
1.2 note - 19 - 56 - note - note -
1.0 note - note - 11 - note - note -
< 1.0 note - note - note - note - note -
Note: Rising input differential signal shall become equal to or greater than VIHdiff(ac) level and Falling input differential signal
shall become equal to or less than VILdiff(ac) level.
Slew Rate
[V/ns]
DDR3L-1600 DDR3L-1866
tDVAC [ps] @ IVIH/Ldiff(ac)I =
320mV
tDVAC [ps] @ IVIH/Ldiff(ac)I =
270mV
tDVAC [ps] @ IVIH/Ldiff(ac)I =
270mV
tDVAC [ps] @ IVIH/Ldiff(ac)I =
250mV
tDVAC [ps] @ IVIH/Ldiff(ac)I =
260mV
Min. Max. Min. Max. Min. Max. Min. Max. Min. Max.
> 4.0 189 - 201 - 163 - 168 - 176 -
4.0 189 - 201 - 163 - 168 - 176 -
3.0 162 - 179 - 140 - 147 - 154 -
2.0 109 - 134 - 95 - 105 - 111 -
1.8 91 - 119 - 80 - 91 - 97 -
1.6 69 - 100 - 62 - 74 - 78 -
1.4 40 - 76 - 37 - 52 - 56 -
1.2 Note - 44 - 5 - 22 - 24 -
1.0 Note - Note - Note - Note - Note -
< 1.0 Note - Note - Note - Note - Note -
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 85/141
Note: Rising input differential signal shall become equal to or greater than VIHdiff(ac) level and Falling input differential signal
shall become equal to or less than VILdiff(ac) level.
Single-ended requirements for differential signals
Each individual component of a differential signal (CK, DQS, DQSL, DQSU, CK , DQS ,DQSL , or DQSU ) has also to comply
with certain requirements for single-ended signals.
CK and CK have to approximately reach VSEHmin / VSELmax (approximately equal to the ac-levels (VIH (ac) / VIL (ac)) for
ADD/CMD signals) in every half-cycle. DQS, DQSL, DQSU, DQS ,DQSL have to reach VSEHmin / VSELmax (approximately the
ac-levels (VIH (ac) / VIL (ac)) for DQ signals) in every half-cycle proceeding and following a valid transition. Note that the applicable ac-levels for ADD/CMD and DQ’s might be different per speed-bin etc. E.g., if VIH150 (ac)/VIL150(ac) is
used for ADD/CMD signals, then these ac-levels apply also for the singleended signals CK and CK .
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 86/141
Single-ended levels for CK, DQS, CK ,DQS ,DQSL , or DQSU
Symbol Parameter DDR3(L)-1600
Unit Notes Min. Max.
VSEH Single-ended high-level for strobes (VDD/2) + 0.175 note3 V 1, 2
Single-ended high-level for CK, CK (VDD/2) + 0.175 note3 V 1, 2
VSEL Single-ended low-level for strobes note3 (VDD/2) - 0.175 V 1, 2
Single-ended Low-level for CK, CK note3 (VDD/2) - 0.175 V 1, 2
Note:
1. For CK, CK use VIH/VIL(ac) of ADD/CMD; for strobes (DQS, DQSL, DQSU, DQS ,DQSL , DQSU ) use VIH/VIL(ac) of DQs.
2. VIH(ac)/VIL(ac) for DQs is based on VREFDQ; VIH(ac)/VIL(ac) for ADD/CMD is based on VREFCA; if a reduced ac-high or
ac-low level is used for a signal group, then the reduced level applies also there.
3. These values are not defined, however the single-ended signals CK, CK , DQS, DQS , DQSL, DQSL , DQSU, DQSU need
to be within the respective limits (VIH(dc)max, VIL(dc)min) for single-ended signals as well as limitations for overshoot and
undershoot.
Differential Input Cross Point Voltage
To guarantee tight setup and hold times as well as output skew parameters with respect to clock and strobe, each cross point
voltage of differential input signals (CK, CK and DQS, DQS ) must meet the requirements in the following table. The
differential input cross point voltage Vix is measured from the actual cross point of true and complete signal to the midlevel between of VDD and VSS.
Vix Definition
VDD
VSS
VDD/2
CK,DQS
CK,DQS
VIX
VIX
VIX
VS
EH
VSEL
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 87/141
Cross point voltage for differential input signals (CK, DQS)
Symbol Parameter DDR3-1600/ 1866 DDR3L-1600/ 1866
Unit Note Min. Max. Min. Max.
VIX(CK) Differential Input Cross Point Voltage
relative to VDD/2 for CK, CK
-150 150 -150 150
mV 1
-175 175 mV 2
VIX(DQ
S)
Differential Input Cross Point Voltage
relative to VDD/2 for DQS, DQS -150 150 -150 150 mV 1
Note:
1. The relation between Vix Min/Max and VSEL/VSEH should satisfy following.
(VDD/2)+Vix (Min.)-VSEL≧25mV
VSEH – ((VDD/2) +Vix (Max.))≧25mV
2. Extended range for Vix is only allowed for clock and if single-ended clock input signals CK and CK are monotonic with a
single-ended swing VSEL / VSEH of at least VDD/2 ± 250mV, and when the differential slew rate of CK - CK is larger than
3V/ns.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 88/141
Slew Rate Definition for Differential Input Signals
Input slew rate for differential signals (CK, CK and DQS, DQS ) are defined and measured as shown below.
Differential Input Slew Rate Definition
Description Measured
Defined by From To
Differential input slew rate for rising edge (CK- CK &
DQS- DQS ) VILdiffmax VIHdiffmin [VIHdiffmin-VILdiffmax] / DeltaTRdiff
Differential input slew rate for falling edge (CK- CK &
DQS- DQS ) VIHdiffmin VILdiffmax [VIHdiffmin-VILdiffmax] / DeltaTFdiff
The differential signal (i.e., CK- CK & DQS- DQS ) must be linear between these thresholds.
Differential Input Slew Rate Definition for DQS, DQS and CK, CK
Input Nominal Slew Rate Definition for single ended signals
Delta
TFdiff
Delta
TRdiff
VIHdiffMin
VILdiffMax
0
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 89/141
AC and DC Output Measurement Levels
Single Ended AC and DC Output Levels
Symbol Parameter Value Unit Notes
VOH(DC) DC output high measurement level (for IV curve linearity) 0.8xVDDQ V
VOM(DC) DC output mid measurement level (for IV curve linearity) 0.5xVDDQ V
VOL(DC) DC output low measurement level (fro IV curve linearity) 0.2xVDDQ V
VOH(AC) AC output high measurement level (for output SR) VTT+0.1xVDDQ V 1
VOL(AC) AC output low measurement level (for output SR) VTT-0.1xVDDQ V 1
Note:
1. The swing of ±0.1 x VDDQ is based on approximately 50% of the static single ended output high or low swing with a driver
impedance of 40 Ω and an effective test load of 25 Ω to VTT = VDDQ/2.
Differential AC and DC Output Levels
Symbol Parameter DDR3(L) Unit Notes
VOHdiff(AC) AC differential output high measurement level (for output SR) +0.2 x VDDQ V 1
VOLdiff(AC) AC differential output low measurement level (for output SR) -0.2 x VDDQ V 1
Note:
1. The swing of ± 0.2 x VDDQ is based on approximately 50% of the static differential output high or low swing with a driver
impedance of 40 Ω and an effective test load of 25 Ω to VTT=VDDQ/2 at each of the differential outputs.
Single Ended Output Slew Rate
Description Measured
Defined by From To
Single ended output slew rate for rising edge VOL(AC) VOH(AC) [VOH(AC)-VOL(AC)] / DeltaTRse
Single ended output slew rate for falling edge VOH(AC) VOL(AC) [VOH(AC)-VOL(AC)] / DeltaTFse
Note: Output slew rate is verified by design and characterization, and may not be subject to production test.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 90/141
Delta TFse
Delta TFse
VOH (AC)
VOL (AC)
VTT
Sing
le E
nded
Out
put V
olta
ge (
i.e. D
Q)
Single Ended Output Slew Rate Definition
Output Slew Rate (single-ended)
Parameter Symbol DDR3-1600/ 1866 DDR3L-1600/ 1866
Unit Min. Max. Min. Max.
Single-ended Output
Slew Rate SRQse 2.5 5 1.75 5 V/ns
Description:
SR: Slew Rate.
Q: Query Output (like in DQ, which stands for Data-in, Query -Output).
se: Single-ended signals.
For Ron = RZQ/7 setting.
Note:
1. In two cases, a maximum slew rate of 6V/ns applis for a single DQ signal within a byte lane.
Case 1 is defined for a single DQ signal within a byte lane which is switching into a certain direction (either form high to low or
low to high) while all remaining DQ signals in the same byte lane are static (i.e. they stay at either high or low).
Case 2 is defined for a single DQ signal within a byte lane which is switching into a certain direction (either from high to low or
low to high) while all remaining DQ signals in the same byte lane are seitching into the opposite direction (i.e. from low to high
or high to low respectively). For the remaining DQ signal switching into the opposite direction, the regular maximum limit of 5
V/ns applies.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 91/141
Differential Output Slew Rate
Description Measured
Defined by From To
Differential output slew rate for rising edge VOLdiff(AC) VOHdiff(AC) [VOHdiff(AC)-VOLdiff(AC)] / DeltaTRdiff
Differential output slew rate for falling edge VOHdiff(AC) VOLdiff(AC) [VOHdiff(AC)-VOLdiff(AC)] / DeltaTFdiff
Note: Output slew rate is verified by design and characterization, and may not be subject to production test.
Differential Output Slew Rate Definition
Differential Output Slew Rate
Parameter Symbol DDR3-1600 DDR3-1866 DDR3L-1600/ 1866
Unit Min. Max. Min. Max. Min. Max.
Single-ended
Output Slew
Rate
SRQdiff 5 10 5 12 3.5 12 V/ns
Description:
SR: Slew Rate.
Q: Query Output (like in DQ, which stands for Data-in, Query -Output).
diff: Differential signals.
For Ron = RZQ/7 setting.
Delta TFse
Delta TFse
VOh diff (AC)
VOL diff (AC)
0
Diff
eren
tial O
utpu
t Vol
tage
(i.e
. DQ
S-D
QS
)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 92/141
Reference Load for AC Timing and Output Slew Rate
The following figure represents the effective reference load of 25 ohms used in defining the relevant AC timing parameters of the device as well as output slew rate measurements.
It is not intended as a precise representation of any particular system environment or a depiction of the actual load presented by a production tester. System designers should use IBIS or other simulation tools to correlate the timing reference load to a system environment. Manufacturers correlate to their production test conditions, generally one or more coaxial transmission lines terminated at the tester electronics.
Vtt = VDDQ/2
25 Ohm
CK , CK
VDDQ
DUT
DQ
DQS
DQS
Timing Reference Points
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 93/141
Overshoot and Undershoot Specifications
AC Overshoot/Undershoot Specification for Address and Control Pins
Item DDR3(L)-1600 DDR3(L)-1866 Units
Maximum peak amplitude allowed for overshoot area 0.4 V
Maximum peak amplitude allowed for undershoot area 0.4 V
Maximum overshoot area above VDD 0.33 0.28 V-ns
Maximum undershoot area below VSS 0.33 0.28 V-ns
Note:
1. The sum of the applied voltage (VDD) and peak amplitude overshoot voltage is not to exceed absolute maximum DC ratings.
2. The sum of applied voltage (VDD) and the peak amplitude undershoot voltage is not to exceed absolute maximum DC ratings.
AC Overshoot/Undershoot Specification for Clock, Data, Strobe, and Mask
Item DDR3(L)-1600 DDR3(L)-1866 Units
Maximum peak amplitude allowed for overshoot area 0.4 V
Maximum peak amplitude allowed for undershoot area 0.4 V
Maximum overshoot area above VDD 0.13 0.11 V-ns
Maximum undershoot area below VSS 0.13 0.11 V-ns
Note:
1. The sum of the applied voltage (VDD) and peak amplitude overshoot voltage is not to exceed absolute maximum DC ratings.
2. The sum of applied voltage (VDD) and the peak amplitude undershoot voltage is not to exceed absolute maximum DC ratings.
VDD
VSS
Overshoot Area
Undershoot Area
Maximum Amplitude
Maximum Amplitude
Time (ns)
Vo
lts (
V)
VDDQ
VSSQ
Overshoot Area
Undershoot Area
Maximum Amplitude
Maximum Amplitude
Time (ns)
Vo
lts (
V)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 94/141
34 Ohm Output Driver DC Electrical Characteristics
A Functional representation of the output buffer is shown as below. Output driver impedance RON is defined by the value of the
external reference resistor RZQ as follows:
RON34 = RZQ / 7 (nominal 34.4ohms +/-10% with nominal RZQ=240ohms)
The individual pull-up and pull-down resistors (RONPu and RONPd) are defined as follows:
RONPu = [VDDQ-Vout] / l Iout l ------------------- under the condition that RONPd is turned off (1)
RONPd = Vout / I Iout I -------------------------------under the condition that RONPu is turned off (2)
Output Driver: Definition of Voltages and Currents
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 95/141
Output Driver DC Electrical Characteristics, assuming RZQ = 240ohms; entire operating temperature range; after proper ZQ calibration
RONNom Resistor Vout Min. Nom. Max. Unit Notes
DDR3
34 ohms
RON34Pd
VOLdc = 0.2 x VDDQ 0.6 1 1.1 RZQ / 7 1,2,3
VOMdc = 0.5 x VDDQ 0.9 1 1.1 RZQ / 7 1,2,3
VOHdc = 0.8 x VDDQ 0.9 1 1.4 RZQ / 7 1,2,3
RON34Pu
VOLdc = 0.2 x VDDQ 0.9 1 1.4 RZQ / 7 1,2,3
VOMdc = 0.5 x VDDQ 0.9 1 1.1 RZQ / 7 1,2,3
VOHdc = 0.8 x VDDQ 0.6 1 1.1 RZQ / 7 1,2,3
40 ohms
RON40pd
VOLdc = 0.2 × VDDQ 0.6 1 1.1 RZQ / 6 1,2,3
VOMdc = 0.5 × VDDQ 0.9 1 1.1 RZQ / 6 1,2,3
VOHdc = 0.8 × VDDQ 0.9 1 1.4 RZQ / 6 1,2,3
RON40pu
VOLdc = 0.2 × VDDQ 0.9 1 1.4 RZQ / 6 1,2,3
VOMdc = 0.5 × VDDQ 0.9 1 1.1 RZQ / 6 1,2,3
VOHdc = 0.8 × VDDQ 0.6 1 1.1 RZQ / 6 1,2,3
Mismatch between pull-up and
pull-down, MMPuPd VOMdc = 0.5 x VDDQ -10 10 % 1,2,4
DDR3L
34 ohms
RON34Pd
VOLdc = 0.2 x VDDQ 0.6 1 1.15 RZQ / 7 1,2,3
VOMdc = 0.5 x VDDQ 0.9 1 1.15 RZQ / 7 1,2,3
VOHdc = 0.8 x VDDQ 0.9 1 1.45 RZQ / 7 1,2,3
RON34Pu
VOLdc = 0.2 x VDDQ 0.9 1 1.45 RZQ / 7 1,2,3
VOMdc = 0.5 x VDDQ 0.9 1 1.15 RZQ / 7 1,2,3
VOHdc = 0.8 x VDDQ 0.6 1 1.15 RZQ / 7 1,2,3
40 ohms
RON40pd
VOLdc = 0.2 × VDDQ 0.6 1 1.15 RZQ / 6 1,2,3
VOMdc = 0.5 × VDDQ 0.9 1 1.15 RZQ / 6 1,2,3
VOHdc = 0.8 × VDDQ 0.9 1 1.45 RZQ / 6 1,2,3
RON40pu
VOLdc = 0.2 × VDDQ 0.9 1 1.45 RZQ / 6 1,2,3
VOMdc = 0.5 × VDDQ 0.9 1 1.15 RZQ / 6 1,2,3
VOHdc = 0.8 × VDDQ 0.6 1 1.15 RZQ / 6 1,2,3
Mismatch between pull-up and
pull-down, MMPuPd VOMdc = 0.5 x VDDQ -10 10 % 1,2,4
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 96/141
Note:
1. The tolerance limits are specified after calibration with stable voltage and temperature. For the behavior of the
tolerance limits if temperature or voltage changes after calibration, see following section on voltage and temperature
sensitivity.
2. The tolerance limits are specified under the condition that VDDQ = VDD and that VSSQ = VSS.
3. Pull-down and pull-up output driver impedances are recommended to be calibrated at 0.5 x VDDQ. Other calibration
schemes may be used to achieve the linearity spec shown above. e.g. calibration at 0.2 x VDDQ and 0.8 x VDDQ.
4. Measurement definition for mismatch between pull-up and pull-down, MMPuPd:
Measure RONPu and RONPd, but at 0.5 x VDDQ:
MMPuPd = [RONPu - RONPd] / RONNom x 100
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 97/141
Output Driver Temperature and Voltage sensitivity
If temperature and/or voltage after calibration, the tolerance limits widen according to the following table.
Delta T = T - T(@calibration); Delta V = VDDQ - VDDQ(@calibration); VDD = VDDQ
Note: dRONdT and dRONdV are not subject to production test but are verified by design and characterization.
Output Driver Sensitivity Definition
Items Min. Max. Unit
RONPU@VOHdc 0.6 - dRONdTH*lDelta Tl - dRONdVH*lDelta Vl 1.1 + dRONdTH*lDelta Tl - dRONdVH*lDelta Vl RZQ/7
RON@VOMdc 0.9 - dRONdTM*lDelta Tl - dRONdVM*lDelta Vl 1.1 + dRONdTM*lDelta Tl - dRONdVM*lDelta Vl RZQ/7
RONPD@VOLdc 0.6 - dRONdTL*lDelta Tl - dRONdVL*lDelta Vl 1.1 + dRONdTL*lDelta Tl - dRONdVL*lDelta Vl RZQ/7
Output Driver Voltage and Temperature Sensitivity
Speed Bin DDR3(L)-1600 Unit
Items Min. Max.
dRONdTM 0 1.5 %/C
dRONdVM 0 0.13 %/mV
dRONdTL 0 1.5 %/C
dRONdVL 0 0.13 %/mV
dRONdTH 0 1.5 %/C
dRONdVH 0 0.13 %/mV
Note: These parameters may not be subject to production test. They are verified by design and characterization.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 98/141
On-Die Termination (ODT) Levels and I-V Characteristics
On-Die Termination effective resistance RTT is defined by bits A9, A6, and A2 of the MR1 Register.
ODT is applied to the DQ, DM, DQS/ DQS .
A functional representation of the on-die termination is shown in the following figure. The individual pull-up and pull-down
resistors (RTTPu and RTTPd) are defined as follows:
RTTPu = [VDDQ - Vout] / I Iout I ------------------ under the condition that RTTPd is turned off (3)
RTTPd = Vout / I Iout I ------------------------------ under the condition that RTTPu is turned off (4)
On-Die Termination: Definition of Voltages and Currents
ODT DC Electrical Characteristics
The following table provides an overview of the ODT DC electrical characteristics. The values for RTT60Pd120, RTT60Pu120,
RTT120Pd240, RTT120Pu240, RTT40Pd80, RTT40Pu80, RTT30Pd60, RTT30Pu60, RTT20Pd40, RTT20Pu40 are not specification requirements, but
can be used as design guide lines:
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 99/141
ODT DC Electrical Characteristics, assuming RZQ = 240ohms +/- 1% entire operating temperature range; after proper ZQ calibration
MR1 A9,A6,A2 RTT Resistor Vout Min. Nom. Max. Unit Notes
DDR3
0,1,0 120Ω
RTT120Pd240
VOLdc = 0.2 x VDDQ 0.6 1 1.1 RZQ 1,2,3,4
0.5 x VDDQ 0.9 1 1.1 RZQ 1,2,3,4
VOHdc = 0.8 x VDDQ 0.9 1 1.4 RZQ 1,2,3,4
RTT120Pu240
VOLdc = 0.2 x VDDQ 0.9 1 1.4 RZQ 1,2,3,4
0.5 x VDDQ 0.9 1 1.1 RZQ 1,2,3,4
VOHdc = 0.8 x VDDQ 0.6 1 1.1 RZQ 1,2,3,4
RTT120 VIL(ac) to VIH(ac) 0.9 1 1.6 RZQ /2 1,2,5
0, 0, 1 60Ω
RTT60Pd120
VOLdc = 0.2 x VDDQ 0.6 1 1.1 RZQ/2 1,2,3,4
0.5 x VDDQ 0.9 1 1.1 RZQ/2 1,2,3,4
VOHdc = 0.8 x VDDQ 0.9 1 1.4 RZQ/2 1,2,3,4
RTT60Pu120
VOLdc = 0.2 x VDDQ 0.9 1 1.4 RZQ/2 1,2,3,4
0.5 x VDDQ 0.9 1 1.1 RZQ/2 1,2,3,4
VOHdc = 0.8 x VDDQ 0.6 1 1.1 RZQ/2 1,2,3,4
RTT60 VIL(ac) to VIH(ac) 0.9 1 1.6 RZQ/4 1,2,5
0, 1, 1 40Ω
RTT40Pd80
VOLdc = 0.2 x VDDQ 0.6 1 1.1 RZQ/3 1,2,3,4
0.5 x VDDQ 0.9 1 1.1 RZQ/3 1,2,3,4
VOHdc = 0.8 x VDDQ 0.9 1 1.4 RZQ/3 1,2,3,4
RTT40Pu80
VOLdc = 0.2 x VDDQ 0.9 1 1.4 RZQ/3 1,2,3,4
0.5 x VDDQ 0.9 1 1.1 RZQ/3 1,2,3,4
VOHdc = 0.8 x VDDQ 0.6 1 1.1 RZQ/3 1,2,3,4
RTT40 VIL(ac) to VIH(ac) 0.9 1 1.6 RZQ/6 1,2,5
1, 0, 1 30Ω
RTT30Pd60
VOLdc = 0.2 x VDDQ 0.6 1 1.1 RZQ/4 1,2,3,4
0.5 x VDDQ 0.9 1 1.1 RZQ/4 1,2,3,4
VOHdc = 0.8 x VDDQ 0.9 1 1.4 RZQ/4 1,2,3,4
RTT30Pu60
VOLdc = 0.2 x VDDQ 0.9 1 1.4 RZQ/4 1,2,3,4
0.5 x VDDQ 0.9 1 1.1 RZQ/4 1,2,3,4
VOHdc = 0.8 x VDDQ 0.6 1 1.1 RZQ/4 1,2,3,4
RTT30 VIL(ac) to VIH(ac) 0.9 1 1.6 RZQ/8 1,2,5
1, 0, 0 20Ω
RTT20Pd40
VOLdc = 0.2 x VDDQ 0.6 1 1.1 RZQ/6 1,2,3,4
0.5 x VDDQ 0.9 1 1.1 RZQ/6 1,2,3,4
VOHdc = 0.8 x VDDQ 0.9 1 1.4 RZQ/6 1,2,3,4
RTT20Pu40
VOLdc = 0.2 x VDDQ 0.9 1 1.4 RZQ/6 1,2,3,4
0.5 x VDDQ 0.9 1 1.1 RZQ/6 1,2,3,4
VOHdc = 0.8 x VDDQ 0.6 1 1.1 RZQ/6 1,2,3,4
RTT20 VIL(ac) to VIH(ac) 0.9 1 1.6 RZQ/12 1,2,5
Deviation of VM w.r.t. VDDQ/2, DVM -5 +5 % 1,2,5,6
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 100/141
MR1 A9,A6,A2 RTT Resistor Vout Min. Nom. Max. Unit Notes
DDR3L
0,1,0 120Ω
RTT120Pd240
VOLdc = 0.2 x VDDQ 0.6 1 1.15 RZQ 1,2,3,4
0.5 x VDDQ 0.9 1 1.15 RZQ 1,2,3,4
VOHdc = 0.8 x VDDQ 0.9 1 1.45 RZQ 1,2,3,4
RTT120Pu240
VOLdc = 0.2 x VDDQ 0.9 1 1.45 RZQ 1,2,3,4
0.5 x VDDQ 0.9 1 1.15 RZQ 1,2,3,4
VOHdc = 0.8 x VDDQ 0.6 1 1.15 RZQ 1,2,3,4
RTT120 VIL(ac) to VIH(ac) 0.9 1 1.65 RZQ /2 1,2,5
0, 0, 1 60Ω
RTT60Pd120
VOLdc = 0.2 x VDDQ 0.6 1 1.15 RZQ/2 1,2,3,4
0.5 x VDDQ 0.9 1 1.15 RZQ/2 1,2,3,4
VOHdc = 0.8 x VDDQ 0.9 1 1.45 RZQ/2 1,2,3,4
RTT60Pu120
VOLdc = 0.2 x VDDQ 0.9 1 1.45 RZQ/2 1,2,3,4
0.5 x VDDQ 0.9 1 1.15 RZQ/2 1,2,3,4
VOHdc = 0.8 x VDDQ 0.6 1 1.15 RZQ/2 1,2,3,4
RTT60 VIL(ac) to VIH(ac) 0.9 1 1.65 RZQ/4 1,2,5
0, 1, 1 40Ω
RTT40Pd80
VOLdc = 0.2 x VDDQ 0.6 1 1.15 RZQ/3 1,2,3,4
0.5 x VDDQ 0.9 1 1.15 RZQ/3 1,2,3,4
VOHdc = 0.8 x VDDQ 0.9 1 1.45 RZQ/3 1,2,3,4
RTT40Pu80
VOLdc = 0.2 x VDDQ 0.9 1 1.45 RZQ/3 1,2,3,4
0.5 x VDDQ 0.9 1 1.15 RZQ/3 1,2,3,4
VOHdc = 0.8 x VDDQ 0.6 1 1.15 RZQ/3 1,2,3,4
RTT40 VIL(ac) to VIH(ac) 0.9 1 1.65 RZQ/6 1,2,5
1, 0, 1 30Ω
RTT30Pd60
VOLdc = 0.2 x VDDQ 0.6 1 1.15 RZQ/4 1,2,3,4
0.5 x VDDQ 0.9 1 1.15 RZQ/4 1,2,3,4
VOHdc = 0.8 x VDDQ 0.9 1 1.45 RZQ/4 1,2,3,4
RTT30Pu60
VOLdc = 0.2 x VDDQ 0.9 1 1.45 RZQ/4 1,2,3,4
0.5 x VDDQ 0.9 1 1.15 RZQ/4 1,2,3,4
VOHdc = 0.8 x VDDQ 0.6 1 1.15 RZQ/4 1,2,3,4
RTT30 VIL(ac) to VIH(ac) 0.9 1 1.65 RZQ/8 1,2,5
1, 0, 0 20Ω
RTT20Pd40
VOLdc = 0.2 x VDDQ 0.6 1 1.15 RZQ/6 1,2,3,4
0.5 x VDDQ 0.9 1 1.15 RZQ/6 1,2,3,4
VOHdc = 0.8 x VDDQ 0.9 1 1.45 RZQ/6 1,2,3,4
RTT20Pu40
VOLdc = 0.2 x VDDQ 0.9 1 1.45 RZQ/6 1,2,3,4
0.5 x VDDQ 0.9 1 1.15 RZQ/6 1,2,3,4
VOHdc = 0.8 x VDDQ 0.6 1 1.15 RZQ/6 1,2,3,4
RTT20 VIL(ac) to VIH(ac) 0.9 1 1.65 RZQ/12 1,2,5
Deviation of VM w.r.t. VDDQ/2, DVM -5 +5 % 1,2,5,6
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 101/141
Note:
1. The tolerance limits are specified after calibration with stable voltage and temperature. For the behavior of the tolerance limits
if temperature or voltage changes after calibration, see following section on voltage and temperature sensitivity.
2. The tolerance limits are specified under the condition that VDDQ = VDD and that VSSQ = VSS.
3. Pull-down and pull-up ODT resistors are recommended to be calibrated at 0.5 x VDDQ. Other calibration may be used to
achieve the linearity spec shown above.
4. Not a specification requirement, but a design guide line.
5. Measurement definition for RTT:
Apply VIH(ac) to pin under test and measure current / (VIH(ac)), then apply VIL(ac) to pin under test and measure current /
(VIL(ac)) respectively.
RTT = [VIH(ac) - VIL(ac)] / [I(VIH(ac)) - I(VIL(ac))]
6. Measurement definition for VM and DVM:
Measure voltage (VM) at test pin (midpoint) with no lead:
Delta VM = [2VM / VDDQ -1] x 100
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 102/141
ODT Temperature and Voltage sensitivity
If temperature and/or voltage after calibration, the tolerance limits widen according to the following table.
Delta T = T - T(@calibration); Delta V = VDDQ - VDDQ(@calibration); VDD = VDDQ
ODT Sensitivity Definition
Min. Max. Unit
RTT 0.9 - dRTTdT*lDelta Tl - dRTTdV*lDelta Vl 1.6 + dRTTdT*lDelta Tl + dRTTdV*lDelta Vl RZQ/2,4,6,8,12
ODT Voltage and Temperature Sensitivity
Min. Max. Unit
dRTTdT 0 1.5 %/C
dRTTdV 0 0.15 %/mV
Note: These parameters may not be subject to production test. They are verified by design and characterization.
Test Load for ODT Timings
Different than for timing measurements, the reference load for ODT timings is defined in the following figure.
ODT Timing Reference Load
Vtt =
25 Ohm
CK ,
VDDQ
DUT
Timing Reference Points
VSSQ
RTT=
DQ , DM
DQS , DQS
TDQS , TDQS
VSSQ
CK
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 103/141
ODT Timing Definitions
Definitions for tAON, tAONPD, tAOF, tAOFPD, and tADC are provided in the following table and subsequent figures.
Symbol Begin Point Definition End Point Definition
tAON Rising edge of CK - CK defined by the end point of ODTLon Extrapolated point at VSSQ
tAONPD Rising edge of CK - CK with ODT being first registered high Extrapolated point at VSSQ
tAOF Rising edge of CK - CK defined by the end point of ODTLoff End point: Extrapolated point at VRTT_Nom
tAOFPD Rising edge of CK - CK with ODT being first registered low End point: Extrapolated point at VRTT_Nom
tADC Rising edge of CK - CK defined by the end point of ODTLcnw,
ODTLcwn4, or ODTLcwn8
End point: Extrapolated point at VRTT_Wr and
VRTT_Nom respectively
Reference Settings for ODT Timing Measurements
Measured
Parameter
RTT_Nom
Setting
RTT_Wr
Setting
DDR3 DDR3L Note
VSW1[V] VSW2[V] VSW1[V] VSW2[V]
tAON RZQ/4 NA 0.05 0.1 0.05 0.1
RZQ/12 NA 0.1 0.2 0.1 0.2
tAONPD RZQ/4 NA 0.05 0.1 0.05 0.1
RZQ/12 NA 0.1 0.2 0.1 0.2
tAOF RZQ/4 NA 0.05 0.1 0.05 0.1
RZQ/12 NA 0.1 0.2 0.1 0.2
tAOFPD RZQ/4 NA 0.05 0.1 0.05 0.1
RZQ/12 NA 0.1 0.2 0.1 0.2
tADC RZQ/12 RZQ/2 0.2 0.3 0.2 0.25
Definition of tAON
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 104/141
Definition of tAONPD
Definition of tAOF
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 105/141
Definition of tAOFPD
Definition of tADC
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 106/141
Input / Output Capacitance
Symbol Parameter DDR3-1600 DDR3L-1600 DDR3-1866 DDR3L-1866
Units Note Min. Max. Min. Max. Min. Max. Min. Max.
CIO Input/output capacitance
(DQ, DM, DQS, DQS ) 1.4 2.3 1.4 2.2 1.4 2.2 1.4 2.1 pF 1,2,3
CCK Input capacitance,
CK and CK 0.8 1.4 0.8 1.4 0.8 1.3 0.8 1.4 pF 2,3
CDCK Input capacitance delta,
CK and CK 0 0.15 0 0.15 0 0.15 0 0.15 pF 2,3,4
CDDQS Input/output capacitance
delta, DQS and DQS 0 0.15 0 0.15 0 0.15 0 0.15 pF 2,3,5
CI Input capacitance, CTRL, ADD, CMD input-only pins
0.75 1.3 0.75 1.2 0.75 1.3 0.75 1.2 pF 2,3,6
CDI_CTR
L
Input capacitance delta, all CTRL input-only pins
-0.4 0.2 -0.4 0.2 -0.4 0.2 -0.4 0.2 pF 2,3,7,
8
CDI_ADD
_CMD
Input capacitance delta, all ADD/CMD input-only pins
-0.4 0.4 -0.4 0.4 -0.4 0.4 -0.4 0.4 pF 2,3,9,
10
CDIO
Input/output capacitance delta, DQ, DM, DQS,
DQS
-0.5 0.3 -0.5 0.3 -0.5 0.3 -0.5 0.3 pF 2,3,11
CZQ Input/output capacitance of ZQ pin
- 3 - 3 - 3 - 3 pF 2,3,12
Note:
1. Although the DM pin has different functions, the loading matches DQ and DQS. 2. This parameter is not subject to production test. It is verified by design and characterization. The capacitance is measured
according to JEP147(“PROCEDURE FOR MEASURING INPUT CAPACITANCE USING A VECTOR NETWORK ANALYZER(VNA)”) with VDD, VDDQ, VSS, VSSQ applied and all other pins floating (except the pin under test, CKE,
RESET and ODT as necessary). VDD=VDDQ=1.5V for DDR3 (VDD=VDDQ=1.35V for DDR3L),, VBIAS=VDD/2 and ondie
termination off. 3. This parameter applies to monolithic devices only; stacked/dual-die devices are not covered here.
4. Absolute value of CCK-C CK .
5. Absolute value of CIO(DQS)-CIO( DQS ).
6. CI applies to ODT, CS , CKE, A0-A13, BA0-BA2,RAS , CAS , WE .
7. CDI_CTRL applies to ODT, CS and CKE.
8. CDI_CTRL=CI(CTRL)-0.5*(CI(CLK)+CI( CLK )).
9. CDI_ADD_CMD applies to A0-A13, BA0-BA2,RAS , CAS and WE .
10. CDI_ADD_CMD=CI(ADD_CMD) - 0.5*(CI(CLK)+CI( CLK )).
11. CDIO=CIO(DQ,DM) - 0.5*(CIO(DQS)+CIO( DQS )).
12. Maximum external load capacitance on ZQ pin: 5 pF.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 107/141
IDD Specifications and Measurement Conditions
IDD Specifications
Symbol Parameter/Condition DDR3-1600 DDR3L-1600 DDR3(L)-1866 Unit
IDD0 Operating Current 0
One Bank Activate -> Precharge 105 100 115 mA
IDD1 Operating Current 1
One Bank Activate -> Read -> Precharge 130 125 150 mA
IDD2P0
(SLOW)
Precharge Power-Down Current
Slow Exit - MR0 bit A12 = 0 20 20 20 mA
IDD2P1
(FAST)
Precharge Power-Down Current
Fast Exit - MR0 bit A12 = 1 45 45 50 mA
IDD2Q Precharge Quiet Standby Current 65 65 70 mA
IDD2N Precharge Standby Current 70 65 75 mA
IDD2NT Precharge Standby ODT IDDQ Current 100 95 100 mA
IDD3N Active Standby Current 95 95 100 mA
IDD3P Active Power-Down Current
Always Fast Exit 65 65 65 mA
IDD4R Operating Current Burst Read 240 230 250 mA
IDD4W Operating Current Burst Write 220 215 230 mA
IDD5B Burst Refresh Current 155 150 150 mA
IDD6 Self-Refresh Current:
Normal Temperature Range (-40-85°C) 12 12 18 mA
IDD6ET Self-Refresh Current:
Extended Temperature Range (-40-105°C) 17 14 20 mA
IDD7 All Bank Interleave Read Current 240 220 250 mA
IDD8 Reset Low Current 14 13 14 mA
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 108/141
IDD Measurement Conditions
Symbol Parameter/Condition
IDD0
Operating One Bank Active-Precharge Current
CKE: High; External clock: On; tCK, nRC, nRAS, CL: see the table of Timings used for IDD and IDDQ;
BL: 8(1); AL: 0; CS : High between ACT and PRE;
Command, Address, Bank Address Inputs: partially toggling; Data IO: MID-LEVEL; DM: stable at 0; Bank Activity: Cycling with one bank active at a time: 0, 0, 1,1,2,2... Output Buffer and RTT: Enabled in Mode Registers (2); ODT Signal: stable at 0.
IDD1
Operating One Bank Active-Read-Precharge Current
CKE: High; External clock: On; tCK, nRC, nRAS, nRCD, CL: see the table of Timings used for IDD and IDDQ;
BL: 8(1, 7); AL: 0; CS : High between ACT, RD and PRE;
Command, Address, Bank Address Inputs, Data IO: partially toggling; Bank Activity: Cycling with one bank active at a time: 0, 0, 1,1,2,2... Output Buffer and RTT: Enabled in Mode Registers (2); ODT Signal: stable at 0.
IDD2N
Precharge Standby Current
CKE: High; External clock: On; tCK, CL: see the table of Timings used for IDD and IDDQ;
BL: 8(1); AL: 0; CS : stable at 1;
Command, Address, Bank Address Inputs: partially toggling; Data IO: MID-LEVEL; DM: stable at 0; Bank Activity: all banks closed; Output Buffer and RTT: Enabled in Mode Registers (2); ODT Signal: stable at 0.
IDD2P(0)
Precharge Power-Down Current Slow Exit
CKE: Low; External clock: On; tCK, CL: see the table of Timings used for IDD and IDDQ;
BL: 8(1); AL: 0; CS : stable at 1;
Command, Address, Bank Address Inputs: stable at 0; Data IO: MID-LEVEL; DM: stable at 0; Bank Activity: all banks closed; Output Buffer and RTT: Enabled in Mode Registers (2); ODT Signal: stable at 0; Pecharge Power Down Mode: Slow Exit (3).
IDD2P(1)
Precharge Power-Down Current Fast Exit
CKE: Low; External clock: On; tCK, CL: see the table of Timings used for IDD and IDDQ;
BL: 8(1); AL: 0; CS : stable at 1;
Command, Address, Bank Address Inputs: stable at 0; Data IO: MID-LEVEL; DM: stable at 0; Bank Activity: all banks closed; Output Buffer and RTT: Enabled in Mode Registers (2); ODT Signal: stable at 0; Pecharge Power Down Mode: Fast Exit (3).
IDD2Q
Precharge Quiet Standby Current
CKE: High; External clock: On; tCK, CL: see the table of Timings used for IDD and IDDQ;
BL: 8(1); AL: 0; CS : stable at 1;
Command, Address, Bank Address Inputs: stable at 0; Data IO: MID-LEVEL; DM: stable at 0; Bank Activity: all banks closed; Output Buffer and RTT: Enabled in Mode Registers (2); ODT Signal: stable at 0.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 109/141
IDD3N
Active Standby Current
CKE: High; External clock: On; tCK, CL: see the table of Timings used for IDD and IDDQ;
BL: 8(1); AL: 0; CS : stable at 1;
Command, Address, Bank Address Inputs: partially toggling; Data IO: MID-LEVEL; DM: stable at 0; Bank Activity: all banks open; Output Buffer and RTT: Enabled in Mode Registers (2); ODT Signal: stable at 0.
IDD3P
Active Power-Down Current
CKE: Low; External clock: On; tCK, CL: see the table of Timings used for IDD and IDDQ;
BL: 8(1); AL: 0; CS : stable at 1;
Command, Address, Bank Address Inputs: stable at 0; Data IO: MID-LEVEL; DM: stable at 0; Bank Activity: all banks open; Output Buffer and RTT: Enabled in Mode Registers (2); ODT Signal: stable at 0.
IDD4R
Operating Burst Read Current
CKE: High; External clock: On; tCK, CL: see the table of Timings used for IDD and IDDQ;
BL: 8(1, 7); AL: 0; CS : High between RD;
Command, Address, Bank Address Inputs: partially toggling; Data IO: seamless read data burst with different data between one burst and the next one; DM:stable at 0; Bank Activity: all banks open, RD commands cycling through banks: 0,0,1,1,2,2,...; Output Buffer and RTT: Enabled in Mode Registers (2); ODT Signal: stable at 0.
IDD4W
Operating Burst Write Current
CKE: High; External clock: On; tCK, CL: see the table of Timings used for IDD and IDDQ;
BL: 8(1); AL: 0; CS : High between WR;
Command, Address, Bank Address Inputs: partially toggling; Data IO: seamless write data burst with different data between one burst and the next one; DM: stable at 0; Bank Activity: all banks open, WR commands cycling through banks: 0, 0, 1,1,2,2...; Output Buffer and RTT: Enabled in Mode Registers (2); ODT Signal: stable at HIGH.
IDD5B
Burst Refresh Current
CKE: High; External clock: On; tCK, CL, nRFC: see the table of Timings used for IDD and IDDQ;
BL: 8(1); AL: 0; CS : High between REF;
Command, Address, Bank Address Inputs: partially toggling; Data IO: MID-LEVEL; DM: stable at 0; Bank Activity: REF command every nRFC; Output Buffer and RTT: Enabled in Mode Registers (2); ODT Signal: stable at 0.
IDD6
Self Refresh Current: Normal Temperature Range
TOPER: -40 - 85°C; Auto Self-Refresh (ASR): Disabled(4); Self-Refresh Temperature Range (SRT): Normal(5);
CKE: Low; External clock: Off; CK and CK : LOW; CL: the table of Timings used for IDD and IDDQ; BL: 8(1); AL: 0;
CS , Command, Address, Bank Address, Data IO: MID-LEVEL; DM:stable at 0;
Bank Activity: Self-Refresh operation; Output Buffer and RTT: Enabled in Mode Registers (2); ODT Signal: MID-LEVEL
IDD6ET
Self-Refresh Current: Extended Temperature Range (optional) (6)
TOPER: -40 - 105°C; Auto Self-Refresh (ASR): Disabled(4); Self-Refresh Temperature Range (SRT): Extended(5);
CKE: Low; External clock: Off; CK and CK : LOW; CL: the table of Timings used for IDD and IDDQ; BL: 8(1); AL: 0;
CS , Command, Address, Bank Address, Data IO: MID-LEVEL; DM: stable at 0;
Bank Activity: Extended Temperature Self-Refresh operation; Output Buffer and RTT: Enabled in Mode Registers(2); ODT Signal: MID-LEVEL.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 110/141
IDD7
Operating Bank Interleave Read Current
CKE: High; External clock: On; tCK, nRC, nRAS, nRCD, nRRD, nFAW, CL: see the table of Timings used for IDD and IDDQ;
BL: 8(1, 7); AL: CL-1; CS : High between ACT and RDA;
Command, Address, Bank Address inputs: partially toggling; Data IO: read data bursts with different data between one burst and the next one; DM:stable at 0; Bank Activity: two times interleaved cycling through banks (0, 1, ...7) with different addressing; Output Buffer and RTT: Enabled in Mode Registers(2); ODT Signal: stable at 0.
IDD8
RESET Low Current
RESET: LOW; External clock: Off; CK and CK : LOW; CKE: FLOATING;
CS , Command, Address, Bank Address, Data IO: FLOATING;
ODT Signal: FLOATING
RESET Low current reading is valid once power is stable and RESET has been LOW for at least 1ms.
Note:
1. Burst Length: BL8 fixed by MRS: set MR0 A[1,0] = 00B. 2. Output Buffer Enable: set MR1 A[12] = 0B; set MR1 A[5,1] = 01B; RTT_Nom enable: set MR1 A[9,6,2] = 011B; RTT_Wr
enable: set MR2 A[10,9] = 10B. 3. Pecharge Power Down Mode: set MR0 A12 = 0B for Slow Exit or MR0 A12 = 1B for Fast Exit. 4. Auto Self-Refresh (ASR): set MR2 A6 = 0B to disable or 1B to enable feature. 5. Self-Refresh Temperature Range (SRT): set MR2 A7 = 0B for normal or 1B for extended temperature range. 6. Refer to DRAM supplier data sheet and/or DIMM SPD to determine if optional features or requirements are supported by
DDR3(L) SDRAM device. 7. Read Burst Type: Nibble Sequential, set MR0 A[3] = 0B.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 111/141
IDD0 Measurement-Loop Pattern1
CK
, /C
K
CK
E
Su
b-L
oo
p
Cy
cle
Nu
mb
er
Co
mm
an
d
/CS
/RA
S
/CA
S
/WE
OD
T
BA
[2:0
]
A[1
4:1
1]
A[1
0]
A[9
:7]
A[6
:3]
A[2
:0]
Data2
tog
glin
g
Sta
tic H
igh
0
0 ACT 0 0 1 1 0 0 00 0 0 0 0 -
1, 2 D, D 1 0 0 0 0 0 00 0 0 0 0 -
3, 4 D#, D# 1 1 1 1 0 0 00 0 0 0 0 -
… repeat pattern 1...4 until nRAS - 1, truncate if necessary
nRAS PRE 0 0 1 0 0 0 00 0 0 0 0 -
… repeat pattern 1...4 until nRC - 1, truncate if necessary
1*nRC + 0 ACT 0 0 1 1 0 0 00 0 0 F 0 -
1*nRC + 1, 2 D, D 1 0 0 0 0 0 00 0 0 F 0 -
1*nRC + 3, 4 D#, D# 1 1 1 1 0 0 00 0 0 F 0 -
… repeat pattern nRC + 1,...,4 until 1*nRC + nRAS - 1, truncate if necessary
1*nRC + nRAS PRE 0 0 1 0 0 0 00 0 0 F 0 -
… repeat nRC + 1,...,4 until 2*nRC - 1, truncate if necessary
1 2*nRC repeat Sub-Loop 0, use BA[2:0] = 1 instead
2 4*nRC repeat Sub-Loop 0, use BA[2:0] = 2 instead
3 6*nRC repeat Sub-Loop 0, use BA[2:0] = 3 instead
4 8*nRC repeat Sub-Loop 0, use BA[2:0] = 4 instead
5 10*nRC repeat Sub-Loop 0, use BA[2:0] = 5 instead
6 12*nRC repeat Sub-Loop 0, use BA[2:0] = 6 instead
7 14*nRC repeat Sub-Loop 0, use BA[2:0] = 7 instead
Note:
1. DM must be driven LOW all the time. DQS, DQS are MID-LEVEL.
2. DQ signals are MID-LEVEL.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 112/141
IDD1 Measurement-Loop Pattern1
CK
, /C
K
CK
E
Su
b-L
oo
p
Cy
cle
Nu
mb
er
Co
mm
an
d
/CS
/RA
S
/CA
S
/WE
OD
T
BA
[2:0
]
A[1
4:1
1]
A[1
0]
A[9
:7]
A[6
:3]
A[2
:0]
Data2
tog
glin
g
Sta
tic H
igh
0
0 ACT 0 0 1 1 0 0 00 0 0 0 0 -
1, 2 D, D 1 0 0 0 0 0 00 0 0 0 0 -
3, 4 D#, D# 1 1 1 1 0 0 00 0 0 0 0 -
… repeat pattern 1...4 until nRCD - 1, truncate if necessary
nRCD RD 0 1 0 1 0 0 00 0 0 0 0 00000000
… repeat pattern 1...4 until nRAS - 1, truncate if necessary
nRAS PRE 0 0 1 0 0 0 00 0 0 0 0 -
… repeat pattern 1...4 until nRC - 1, truncate if necessary
1*nRC + 0 ACT 0 0 1 1 0 0 00 0 0 F 0 -
1*nRC + 1, 2 D, D 1 0 0 0 0 0 00 0 0 F 0 -
1*nRC + 3, 4 D#, D# 1 1 1 1 0 0 00 0 0 F 0 -
… repeat pattern nRC + 1,..., 4 until nRC + nRCD - 1, truncate if necessary
1*nRC + nRCD RD 0 1 0 1 0 0 00 0 0 F 0 00110011
… repeat pattern nRC + 1,..., 4 until nRC + nRAS - 1, truncate if necessary
1*nRC + nRAS PRE 0 0 1 0 0 0 00 0 0 F 0 -
… repeat pattern nRC + 1,..., 4 until 2 * nRC - 1, truncate if necessary
1 2*nRC repeat Sub-Loop 0, use BA[2:0] = 1 instead
2 4*nRC repeat Sub-Loop 0, use BA[2:0] = 2 instead
3 6*nRC repeat Sub-Loop 0, use BA[2:0] = 3 instead
4 8*nRC repeat Sub-Loop 0, use BA[2:0] = 4 instead
5 10*nRC repeat Sub-Loop 0, use BA[2:0] = 5 instead
6 12*nRC repeat Sub-Loop 0, use BA[2:0] = 6 instead
7 14*nRC repeat Sub-Loop 0, use BA[2:0] = 7 instead
Note:
1. DM must be driven LOW all the time. DQS, DQS are used according to RD Commands, otherwise MID-LEVEL.
2. Burst Sequence driven on each DQ signal by Read Command. Outside burst operation, DQ signals are MID-LEVEL.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 113/141
IDD2N and IDD3N Measurement-Loop Pattern1
CK
, /C
K
CK
E
Su
b-L
oo
p
Cy
cle
Nu
mb
er
Co
mm
an
d
/CS
/RA
S
/CA
S
/WE
OD
T
BA
[2:0
]
A[1
4:1
1]
A[1
0]
A[9
:7]
A[6
:3]
A[2
:0]
Data2
tog
glin
g
Sta
tic H
igh
0
0 D 1 0 0 0 0 0 0 0 0 0 0 -
1 D 1 0 0 0 0 0 0 0 0 0 0 -
2 D# 1 1 1 1 0 0 0 0 0 F 0 -
3 D# 1 1 1 1 0 0 0 0 0 F 0 -
1 4-7 repeat Sub-Loop 0, use BA[2:0] = 1 instead
2 8-11 repeat Sub-Loop 0, use BA[2:0] = 2 instead
3 12-15 repeat Sub-Loop 0, use BA[2:0] = 3 instead
4 16-19 repeat Sub-Loop 0, use BA[2:0] = 4 instead
5 20-23 repeat Sub-Loop 0, use BA[2:0] = 5 instead
6 24-27 repeat Sub-Loop 0, use BA[2:0] = 6 instead
7 28-31 repeat Sub-Loop 0, use BA[2:0] = 7 instead
Note:
1. DM must be driven LOW all the time. DQS, DQS are MID-LEVEL.
2. DQ signals are MID-LEVEL.
IDD2NT and IDDQ2NT Measurement-Loop Pattern
1
CK
, /C
K
CK
E
Su
b-L
oo
p
Cyc
le
Nu
mb
er
Co
mm
an
d
/CS
/RA
S
/CA
S
/WE
OD
T
BA
[2:0
]
A[1
4:1
1]
A[1
0]
A[9
:7]
A[6
:3]
A[2
:0]
Data2
tog
glin
g
Sta
tic H
igh
0
0 D 1 0 0 0 0 0 0 0 0 0 0 -
1 D 1 0 0 0 0 0 0 0 0 0 0 -
2 D# 1 1 1 1 0 0 0 0 0 F 0 -
3 D# 1 1 1 1 0 0 0 0 0 F 0 -
1 4-7 repeat Sub-Loop 0, but ODT = 0 and BA[2:0] = 1
2 8-11 repeat Sub-Loop 0, but ODT = 0 and BA[2:0] = 2
3 12-15 repeat Sub-Loop 0, but ODT = 1 and BA[2:0] = 3
4 16-19 repeat Sub-Loop 0, but ODT = 1 and BA[2:0] = 4
5 20-23 repeat Sub-Loop 0, but ODT = 0 and BA[2:0] = 5
6 24-27 repeat Sub-Loop 0, but ODT = 1 and BA[2:0] = 6
7 28-31 repeat Sub-Loop 0, but ODT = 1 and BA[2:0] = 7
Note:
1. DM must be driven LOW all the time. DQS, DQS are MID-LEVEL.
2. DQ signals are MID-LEVEL.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 114/141
IDD4R and IDDQ4R Measurement-Loop Pattern1
CK
, /C
K
CK
E
Su
b-L
oo
p
Cy
cle
Nu
mb
er
Co
mm
an
d
/CS
/RA
S
/CA
S
/WE
OD
T
BA
[2:0
]
A[1
4:1
1]
A[1
0]
A[9
:7]
A[6
:3]
A[2
:0]
Data2
tog
glin
g
Sta
tic H
igh
0
0 RD 0 1 0 1 0 0 00 0 0 0 0 00000000
1 D 1 0 0 0 0 0 00 0 0 0 0 -
2, 3 D#, D# 1 1 1 1 0 0 00 0 0 0 0 -
4 RD 0 1 0 1 0 0 00 0 0 F 0 00110011
5 D 1 0 0 0 0 0 00 0 0 F 0 -
6, 7 D#, D# 1 1 1 1 0 0 00 0 0 F 0 -
1 8-15 repeat Sub-Loop 0, but BA[2:0] = 1
2 16-23 repeat Sub-Loop 0, but BA[2:0] = 2
3 24-31 repeat Sub-Loop 0, but BA[2:0] = 3
4 32-39 repeat Sub-Loop 0, but BA[2:0] = 4
5 40-47 repeat Sub-Loop 0, but BA[2:0] = 5
6 48-55 repeat Sub-Loop 0, but BA[2:0] = 6
7 56-63 repeat Sub-Loop 0, but BA[2:0] = 7
Note:
1. DM must be driven LOW all the time. DQS, DQS are used according to RD Commands, otherwise MID-LEVEL.
2. Burst Sequence driven on each DQ signal by Read Command. Outside burst operation, DQ signals are MID-LEVEL.
IDD4W Measurement-Loop Pattern1
CK
, /C
K
CK
E
Su
b-L
oo
p
Cyc
le
Nu
mb
er
Co
mm
an
d
/CS
/RA
S
/CA
S
/WE
OD
T
BA
[2:0
]
A[1
4:1
1]
A[1
0]
A[9
:7]
A[6
:3]
A[2
:0]
Data2
tog
glin
g
Sta
tic H
igh
0
0 WR 0 1 0 0 1 0 00 0 0 0 0 00000000
1 D 1 0 0 0 1 0 00 0 0 0 0 -
2, 3 D#, D# 1 1 1 1 1 0 00 0 0 0 0 -
4 WR 0 1 0 0 1 0 00 0 0 F 0 00110011
5 D 1 0 0 0 1 0 00 0 0 F 0 -
6, 7 D#, D# 1 1 1 1 1 0 00 0 0 F 0 -
1 8-15 repeat Sub-Loop 0, but BA[2:0] = 1
2 16-23 repeat Sub-Loop 0, but BA[2:0] = 2
3 24-31 repeat Sub-Loop 0, but BA[2:0] = 3
4 32-39 repeat Sub-Loop 0, but BA[2:0] = 4
5 40-47 repeat Sub-Loop 0, but BA[2:0] = 5
6 48-55 repeat Sub-Loop 0, but BA[2:0] = 6
7 56-63 repeat Sub-Loop 0, but BA[2:0] = 7
Note:
1. DM must be driven LOW all the time. DQS, DQS are used according to WR Commands, otherwise MID-LEVEL.
2. Burst Sequence driven on each DQ signal by Write Command. Outside burst operation, DQ signals are MID-LEVEL.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 115/141
IDD5B Measurement-Loop Pattern1
CK
, /C
K
CK
E
Su
b-L
oo
p
Cy
cle
Nu
mb
er
Co
mm
an
d
/CS
/RA
S
/CA
S
/WE
OD
T
BA
[2:0
]
A[1
4:1
1]
A[1
0]
A[9
:7]
A[6
:3]
A[2
:0]
Data2
tog
glin
g
Sta
tic H
igh
0 0 REF 0 0 0 1 0 0 0 0 0 0 0 -
1
1, 2 D, D 1 0 0 0 0 0 00 0 0 0 0 -
3, 4 D#, D# 1 1 1 1 0 0 00 0 0 F 0 -
5….8 repeat cycles 1...4, but BA[2:0] = 1
9….12 repeat cycles 1...4, but BA[2:0] = 2
13….16 repeat cycles 1...4, but BA[2:0] = 3
17….20 repeat cycles 1...4, but BA[2:0] = 4
21….24 repeat cycles 1...4, but BA[2:0] = 5
25….28 repeat cycles 1...4, but BA[2:0] = 6
29….32 repeat cycles 1...4, but BA[2:0] = 7
2 33….nRFC-1 repeat Sub-Loop 1, until nRFC - 1. Truncate, if necessary.
Note:
1. DM must be driven LOW all the time. DQS, DQS are MID-LEVEL.
2. DQ signals are MID-LEVEL.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 116/141
IDD7 Measurement-Loop Pattern1
ATTENTION: Sub-Loops 10-19 have inverse A[6:3] Pattern and Data Pattern than Sub-Loops 0-9
CK
, /C
K
CK
E
Su
b-L
oo
p
Cy
cle
Nu
mb
er
Co
mm
an
d
/CS
/RA
S
/CA
S
/WE
OD
T
BA
[2:0
]
A[1
4:1
1]
A[1
0]
A[9
:7]
A[6
:3]
A[2
:0]
Data2
tog
glin
g
Sta
tic H
igh
0
0 ACT 0 0 1 1 0 0 00 0 0 0 0 -
1 RDA 0 1 0 1 0 0 00 1 0 0 0 00000000
2 D 1 0 0 0 0 0 00 0 0 0 0 -
… repeat above D Command until nRRD - 1
1
nRRD ACT 0 0 1 1 0 1 00 0 0 F 0 -
nRRD + 1 RDA 0 1 0 1 0 1 00 1 0 F 0 00110011
nRRD + 2 D 1 0 0 0 0 1 00 0 0 F 0 -
… repeat above D Command until 2 * nRRD - 1
2 2*nRRD repeat Sub-Loop 0, but BA[2:0] = 2
3 3*nRRD repeat Sub-Loop 1, but BA[2:0] = 3
4 4*nRRD D 1 0 0 0 0 3 00 0 0 F 0 -
Assert and repeat above D Command until nFAW - 1, if necessary
5 nFAW repeat Sub-Loop 0, but BA[2:0] = 4
6 nFAW + nRRD repeat Sub-Loop 1, but BA[2:0] = 5
7 nFAW + 2*nRRD repeat Sub-Loop 0, but BA[2:0] = 6
8 nFAW + 3*nRRD repeat Sub-Loop 1, but BA[2:0] = 7
9 nFAW + 4*nRRD D 1 0 0 0 0 7 00 0 0 F 0 -
Assert and repeat above D Command until 2 * nFAW - 1, if necessary
10
2*nFAW + 0 ACT 0 0 1 1 0 0 00 0 0 F 0 -
2*nFAW + 1 RDA 0 1 0 1 0 0 00 1 0 F 0 00110011
2*nFAW + 2 D 1 0 0 0 0 0 00 0 0 F 0 -
Repeat above D Command until 2 * nFAW + nRRD - 1
11
2*nFAW+nRRD ACT 0 0 1 1 0 1 00 0 0 0 0 -
2*nFAW+nRRD+1 RDA 0 1 0 1 0 1 00 1 0 0 0 00000000
2*nFAW+nRRD+2 D 1 0 0 0 0 1 00 0 0 0 0 -
repeat above D Command until 2 * nFAW + 2 * nRRD -1
12 2*nFAW+2*nRRD repeat Sub-Loop 10, but BA[2:0] = 2
13 2*nFAW+3*nRRD repeat Sub-Loop 11, but BA[2:0] = 3
14 2*nFAW+4*nRRD D 1 0 0 0 0 3 00 0 0 0 0 -
Assert and repeat above D Command until 3 * nFAW - 1, if necessary
15 3*nFAW repeat Sub-Loop 10, but BA[2:0] = 4
16 3*nFAW+nRRD repeat Sub-Loop 11, but BA[2:0] = 5
17 3*nFAW+2*nRRD repeat Sub-Loop 10, but BA[2:0] = 6
18 3*nFAW+3*nRRD repeat Sub-Loop 11, but BA[2:0] = 7
19 3*nFAW+4*nRRD D 1 0 0 0 0 7 00 0 0 0 0 -
Assert and repeat above D Command until 4 * nFAW - 1, if necessary
Note:
1. DM must be driven LOW all the time. DQS, DQS are used according to RD Commands, otherwise MID-LEVEL.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 117/141
2. Burst Sequence driven on each DQ signal by Read Command. Outside burst operation, DQ signals are MID-LEVEL.
Fundamental AC Specifications – Operating Frequency
Speed Bins DDR3(L)-1866 (13-13-13) Unit
Parameter Min Max
tCK (avg)
CL5 CWL5 Reserved ns
CWL6/7/8/9 Reserved ns
CL6
CWL5 2.5 3.3 ns
CWL6 Reserved ns
CWL7/8/9 Reserved ns
CL7
CWL5 Reserved ns
CWL6 1.875 < 2.5 ns
CWL7/8/9 Reserved ns
CL8
CWL5 Reserved ns
CWL6 1.875 < 2.5 ns
CWL7 Reserved ns
CWL8/9 Reserved ns
CL9
CWL5/6 Reserved ns
CWL7 1.5 < 1.875 ns
CWL8 Reserved ns
CWL9 Reserved ns
CL10
CWL5/6 Reserved ns
CWL7 1.5 < 1.875 ns
CWL8 Reserved ns
CL11
CWL5/6/7 Reserved ns
CWL8 1.25 < 1.5 ns
CWL9 Reserved ns
CL12 CWL5/6/7/8 Reserved ns
CWL9 < 1.25 Reserved ns
CL13 CWL5/6/7/8 Reserved ns
CWL9 1.07 < 1.25 ns
Supported CL 6,7,8,9,10,11,13 nCK
Supported CWL 5,6,7,8,9 nCK
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 118/141
Fundamental AC Specifications – Operating Frequency
Speed Bins DDR3(L)-1600 (11-11-11) Unit
Parameter Min Max
tCK (avg)
CL5 CWL5 3.0 3.3 ns
CWL6/7/8 Reserved ns
CL6
CWL5 2.5 3.3 ns
CWL6 Reserved ns
CWL7/8 Reserved ns
CL7
CWL5 Reserved ns
CWL6 1.875 < 2.5 ns
CWL7 Reserved ns
CWL8 Reserved ns
CL8
CWL5 Reserved ns
CWL6 1.875 < 2.5 ns
CWL7 Reserved ns
CWL8 Reserved ns
CL9
CWL5/6 Reserved ns
CWL7 1.5 < 1.875 ns
CWL8 Reserved ns
CL10
CWL5/6 Reserved ns
CWL7 1.5 < 1.875 ns
CWL8 Reserved ns
CL11 CWL5/6/7 Reserved ns
CWL8 1.25 < 1.5 ns
Supported CL 5,6,7,8,9,10,11 nCK
Supported CWL 5,6,7,8 nCK
Fundamental AC Specifications Notes
1. The CL setting and CWL setting result in tCK(avg).MIN and tCK(avg).MAX requirements. When making a selection of tCK(avg), both need to be fulfilled: Requirements from CL setting as well as requirements from CWL setting.
2. tCK(avg).MIN limits: Since CAS Latency is not purely analog - data and strobe output are synchronized by the DLL - all possible intermediate frequencies may not be guaranteed. An application should use the next smaller JEDEC standard tCK(avg) value (3.0, 2.5, 1.875, 1.5, 1.25, 1.07 ns) when calculating CL [nCK] = tAA [ns] / tCK(Avg) [ns], rounding up to the next ‘Supported CL’, where tCK(avg) = 3.0 ns should only be used for CL = 5 calculation.
3. tCK(avg).MAX limits: Calculate tCK(avg) = tAA.MAX / CL SELECTED and round the resulting tCK(avg) down to the next valid speed bin (i.e. 3.3ns or 2.5ns or 1.875 ns or 1.5 ns or 1.25 ns or 1.07 ns). This result is tCK(avg).MAX corresponding to CL SELECTED.
4. ‘Reserved’ settings are not allowed. User must program a different value. 5. Any DDR3(L)-1600 speed bin also supports functional operation at lower frequencies as shown in the table which are not
subject to Production Tests but verified by Design/Characterization. 6. Any DDR3(L)-1866 speed bin also supports functional operation at lower frequencies as shown in the table which are not
subject to Production Tests but verified by Design/Characterization. 7. For devices supporting optional down binning to CL=7 and CL=9, tAA/tRCD/tRPmin must be 13.125 ns. SPD settings must
be programmed to match. For example, DDR3(L)-1333(9-9-9) devices supporting down binning to DDR3(L)-1066(7-7-7) should program 13.125ns in SPD bytes for tAAmin (Byte 16), tRCDmin (Byte 18), and tRPmin (Byte 20). DDR3(L)-1600(11-11-11) devices supporting down binning to DDR3(L)-1333(9-9-9) or DDR3(L)-1066(7-7-7)should program 13.125ns in SPD bytes for tAAmin (Byte 16), tRCDmin (Byte 18), and tRPmin( Byte 20). Once tRP (Byte 20) us origranned ti 13.125ns, tRCmin (Byte 21,23) also should be programmed accordingly. For example, 49.125ns (tRASmin +tRPmin = 36ns + 13.125ns) for DDR3(L)-1333(9-9-9) and 48.125ns (tRASmin + tRPmin = 35ns + 13.125ns) for DDR3(L)-1600(11-11-11).
8. For CL5 support, refer to DIMM SPD information. DRAM is required to support CL5. CL5 is not mandatory in SPD coding.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 119/141
9. For devices supporting optional down binning to CL=11, CL=9 and CL=7, tAA/tRCD/tRPmin must be 13.125ns. SPD setting must be programed to match. For example, DDR3(L)-1866(13-13-13) devices supporting down binning to DDR3(L)-1600(11-11-11) or DDR3(L)-1333(9-9-9) or 1066(7-7-7) should program 13.125ns in SPD bytes for tAAmin(byte16), tRCDmin(Byte18) and tRPmin (byte20). Once tRP (Byte 20) is programmed to 13.125ns, tRCmin (Byte 21,23) also should be programmed accordingly. For example, 47.125ns (tRASmin + tRPmin = 34 ns+ 13.125 ns).
Fundamental AC Specifications – Core Timing
Speed Bins DDR3(L)-1866
(13-13-13) DDR3(L)-1600
(11-11-11) Unit
Parameter Min Max Min Max
tAA 13.91 20 13.75 20 ns
tRCD 13.91 - 13.75 - ns
tRP 13.91 - 13.75 - ns
tRC 47.91 - 48.75 - ns
tRAS 34 9*tREFI 35 9*tREFI ns
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 120/141
Electrical Characteristics & AC Timing
Timing Parameter for (DDR3(L)-1600)
Parameter Symbol DDR3-1600 DDR3L-1600
Units Min. Max. Min. Max.
Clock Timing
Minimum Clock Cycle Time (DLL off mode)
tCK (DLL_off) 8 - 8 - ns
Average Clock Period tCK(avg) Refer to “Fundamental AC Specifications”
Average high pulse width tCH(avg) 0.47 0.53 0.47 0.53 tCK(avg)
Average low pulse width tCL(avg) 0.47 0.53 0.47 0.53 tCK(avg)
Absolute Clock Period tCK(abs) Min.: tCK(avg)min + tJIT(per)min
Max.: tCK(avg)max + tJIT(per)max ps
Absolute clock HIGH pulse width tCH(abs) 0.43 - 0.43 - tCK(avg)
Absolute clock LOW pulse width tCL(abs) 0.43 - 0.43 - tCK(avg)
Clock Period Jitter JIT(per) -70 70 -70 70 ps
Clock Period Jitter during DLL locking period
JIT(per, lck) -60 60 -60 60 ps
Cycle to Cycle Period Jitter tJIT(cc) 140 140 ps
Cycle to Cycle Period Jitter during DLL locking period
JIT(cc, lck) 120 120 ps
Duty Cycle Jitter tJIT(duty) - - - - ps
Cumulative error across n = 2, 14…..49,50 cycles
tERR(nper) tERR(nper)min = (1 + 0.68ln(n)) * tJIT(per)min
tERR(nper)max = (1 + 0.68ln(n)) * tJIT(per)max ps
Data Timing
DQS, DQS to DQ skew, per
group, per access tDQSQ - 100 - 100 ps
DQ output hold time from DQS,
DQS tQH 0.38 - 0.38 - tCK(avg)
DQ low-impedance time from
CK, CK tLZ(DQ) -450 225 -450 225 ps
DQ high-impedance time from
CK, CK tHZ(DQ) - 225 - 225 ps
Data setup time to DQS, DQS referenced to Vih(ac) / Vil(ac) levels
tDS(base) 10 - 25 - ps
Data hold time from DQS, DQS referenced to Vih(dc) / Vil(dc) levels
tDH(base)
DC100 45 - - - ps
tDH(base)
DC90 - - 55 -
DQ and DM Input pulse width for each input
tDIPW 360 - 360 - ps
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 121/141
Parameter Symbol DDR3-1600 DDR3L-1600
Units Min. Max. Min. Max.
Data Strobe Timing
DQS, DQS differential READ
Preamble tRPRE 0.9 Note 19 0.9 Note 19 tCK(avg)
DQS, DQS differential READ
Postamble tRPST 0.3 Note 11 0.3 Note 11 tCK(avg)
DQS, DQS differential output
high time tQSH 0.4 - 0.4 - tCK(avg)
DQS, DQS differential output low
time tQSL 0.4 - 0.4 - tCK(avg)
DQS, DQS differential WRITE
Preamble tWPRE 0.9 - 0.9 - tCK(avg)
DQS, DQS differential WRITE
Postamble tWPST 0.3 - 0.3 - tCK(avg)
DQS, DQS rising edge output
access time from rising CK, CK tDQSCK -225 225 -225 225 ps
DQS and DQS low-impedance
time (Referenced from RL-1) tLZ(DQS) -450 225 -450 225 ps
DQS and DQS high-impedance
time (Referenced from RL+BL/2) tHZ(DQS) - 225 - 225 ps
DQS, DQS differential input low
pulse width tDQSL 0.45 0.55 0.45 0.55 tCK(avg)
DQS, DQS differential input high
pulse width tDQSH 0.45 0.55 0.45 0.55 tCK(avg)
DQS, DQS rising edge to CK,
CK rising edge tDQSS -0.27 0.27 -0.27 0.27 tCK(avg)
DQS, DQS falling edge setup
time to CK, CK rising edge tDSS 0.18 - 0.18 - tCK(avg)
DQS, DQS falling edge hold time
from CK, CK rising edge tDSH 0.18 - 0.18 - tCK(avg)
Command and Address Timing
DLL locking time tDLLK 512 - 512 - nCK
Internal READ Command to PRECHARGE Command delay
tRTP tRTPmin.: max(4tCK, 7.5ns)
tRTPmax. -
Delay from start of internal write transaction to internal read command
tWTR tWTRmin.: max(4tCK, 7.5ns)
tWTRmax.: -
WRITE recovery time tWR 15 - 15 - ns
Mode Register Set command cycle time
tMRD 4 - 4 - nCK
Mode Register Set command update delay
tMOD tMODmin.: max(12tCK, 15ns)
tMODmax.: -
ACT to internal read or write delay time
tRCD
Refer to “Fundamental AC Specifications”
PRE command period tRP
ACT to ACT or REF command period
tRC
ACTIVE to PRECHARGE command period
tRAS
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 122/141
Parameter Symbol DDR3-1600 DDR3L-1600
Units Min. Max. Min. Max.
CAS to CAS command delay tCCD 4 - 4 - nCK
Auto precharge write recovery + precharge time
tDAL(min) WR + roundup(tRP / tCK(avg)) nCK
Multi-Purpose Register Recovery Time
tMPRR 1 - 1 - nCK
ACTIVE to ACTIVE command period for 2KB page size
tRRD max(4tCK,
7.5ns) -
max(4tCK, 7.5ns)
-
Four activate window for 2KB page size
tFAW 40 - 40 - ns
Command and Address setup
time to CK, CK referenced to
Vih(ac) / Vil(ac) levels
tIS(base) (AC175)
45 - - - ps
tIS(base) (AC160)
- - 60 - ps
tIS(base) (AC150)
170 - - - ps
tIS(base) (AC135)
- - 185 - ps
Command and Address hold time
from CK, CK referenced to
Vih(dc) / Vil(dc) levels
tIH(base) DDR3 DC100
120 - - - ps
Command and Address hold time
from CK, CK referenced to
Vih(dc) / Vil(dc) levels
tIH(base) DDR3L DC90
- - 130 - ps
Control and Address Input pulse width for each input
tIPW 560 - 560 - ps
Calibration Timing
Power-up and RESET calibration time
tZQinit tZQinit, min: max(512 tCK, 640ns)
tZQinit, max: -
Normal operation Full calibration time
tZQoper tZQoper, min: max(256 tCK, 320ns)
tZQoper, max: -
Normal operation Short calibration time
tZQCS tZQCSmin: max(64 tCK, 80ns)
tZQCSmax: -
Reset Timing
Exit Reset from CKE HIGH to a valid command
tXPR tXPRmin: max(5 tCK, tRFC(min) + 10ns)
tXPRmax: -
Self Refresh Timings
Exit Self Refresh to commands not requiring a locked DLL
tXS tXSmin: max(5 tCK, tRFC(min) + 10ns)
tXSmax: -
Exit Self Refresh to commands requiring a locked DLL
tXSDLL tXSDLLmin: tDLLK(min)
tXSDLLmax: - nCK
Minimum CKE low width for Self Refresh entry to exit timing
tCKESR tCKESRmin: tCKE(min) + 1 tCK
tCKESRmax: -
Valid Clock Requirement after Self Refresh Entry (SRE) or Power-Down Entry (PDE)
tCKSRE tCKSREmin: max(5 tCK, 10 ns)
tCKSREmax: -
Valid Clock Requirement before Self Refresh Exit (SRX) or Power-Down Exit (PDX) or Reset Exit
tCKSRX tCKSRXmin: max(5 tCK, 10 ns)
tCKSRXmax: -
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 123/141
Parameter Symbol DDR3-1600 DDR3L-1600
Units Min. Max. Min. Max.
Power Down Timings
Exit Power Down with DLL on to any valid command; Exit Precharge Power Down with DLL frozen to commands not requiring a locked DLL
tXP max(3tCK, 6ns) - max(3tCK, 6ns) -
CKE minimum pulse width tCKE max(3tCK, 5ns) - max(3tCK, 5ns) -
Exit Precharge Power Down with DLL frozen to commands requiring a locked DLL
tXPDLL tXPDLLmin: max(10 tCK, 24ns)
tXPDLLmax: -
Command pass disable delay tCPDED tCPDEDmin: 1 tCPDEDmax: -
nCK
Power Down Entry to Exit Timing tPD tPDmin: tCKE(min) tPDmax: 9*tREFI
Timing of ACT command to Power Down entry
tACTPDEN tACTPDENmin: 1 tACTPDENmax: -
nCK
Timing of PRE or PREA command to Power Down entry
tPRPDEN tPRPDENmin: 1 tPRPDENmax: -
nCK
Timing of RD/RDA command to Power Down entry
tRDPDEN tRDPDENmin: RL+4+1
tRDPDENmax: - nCK
Timing of WR command to Power Down entry (BL8OTF, BL8MRS, BC4OTF)
tWRPDEN tWRPDENmin: WL + 4 + (tWR / tCK(avg))
tWRPDENmax: - nCK
Timing of WRA command to Power Down entry (BL8OTF, BL8MRS, BC4OTF)
tWRAPDEN tWRAPDENmin: WL+4+WR+1
tWRAPDENmax: - nCK
Timing of WR command to Power Down entry (BC4MRS)
tWRPDEN tWRPDENmin: WL + 2 + (tWR / tCK(avg))
tWRPDENmax: - nCK
Timing of WRA command to Power Down entry (BC4MRS)
tWRAPDEN tWRAPDENmin: WL + 2 +WR + 1
tWRAPDENmax: - nCK
Timing of REF command to Power Down entry
tREFPDEN tREFPDENmin: 1 tREFPDENmax: -
nCK
Timing of MRS command to Power Down entry
tMRSPDEN tMRSPDENmin: tMOD(min)
tMRSPDENmax: -
ODT Timings
ODT turn on Latency ODTLon WL-2=CWL+AL-2 nCK
ODT turn off Latency ODTLoff WL-2=CWL+AL-2 nCK
ODT high time without write command or with write command and BC4
ODTH4 ODTH4min: 4 ODTH4max: -
nCK
ODT high time with Write command and BL8
ODTH8 ODTH8min: 6 ODTH8max: -
nCK
Asynchronous RTT turn-on delay (Power-Down with DLL frozen)
tAONPD 2 8.5 2 8.5 ns
Asynchronous RTT turn-off delay (Power-Down with DLL frozen)
tAOFPD 2 8.5 2 8.5 ns
RTT turn-on tAON -225 225 -225 225 ps
RTT_Nom and RTT_WR turn-off time from ODTLoff reference
tAOF 0.3 0.7 0.3 0.7 tCK(avg)
RTT dynamic change skew tADC 0.3 0.7 0.3 0.7 tCK(avg)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 124/141
Parameter Symbol DDR3-1600 DDR3L-1600
Units Min. Max. Min. Max.
Write Leveling Timings
First DQS/ DQS rising edge after
write leveling mode is programmed
tWLMRD 40 - 40 - nCK
DQS/ DQS delay after write
leveling mode is programmed tWLDQSEN 25 - 25 - nCK
Write leveling setup time from
rising CK, CK crossing to rising
DQS, DQS crossing
tWLS 165 - 165 - ps
Write leveling hold time from
rising DQS, DQS crossing to
rising CK, CK crossing
tWLH 165 - 165 - ps
Write leveling output delay tWLO 0 7.5 0 7.5 ns
Write leveling output error tWLOE 0 2 0 2 ns
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 125/141
Timing Parameter for (DDR3(L)-1866)
Parameter Symbol DDR3-1866 DDR3L-1866
Units Min. Max. Min. Max.
Clock Timing
Minimum Clock Cycle Time (DLL off mode)
tCK (DLL_off) 8 - 8 - ns
Average Clock Period tCK(avg) Refer to “Fundamental AC Specifications”
Average high pulse width tCH(avg) 0.47 0.53 0.47 0.53 tCK(avg)
Average low pulse width tCL(avg) 0.47 0.53 0.47 0.53 tCK(avg)
Absolute Clock Period tCK(abs) Min.: tCK(avg)min + tJIT(per)min
Max.: tCK(avg)max + tJIT(per)max
Absolute clock HIGH pulse width tCH(abs) 0.43 - 0.43 - tCK(avg)
Absolute clock LOW pulse width tCL(abs) 0.43 - 0.43 - tCK(avg)
Clock Period Jitter JIT(per) -60 60 -60 60 ps
Clock Period Jitter during DLL locking period
JIT(per, lck) -50 50 -50 50 ps
Cycle to Cycle Period Jitter tJIT(cc) 120 120 ps
Cycle to Cycle Period Jitter during DLL locking period
JIT(cc, lck) 100 100 ps
Duty Cycle Jitter tJIT(duty) - - - - ps
Cumulative error across n = 2, 14…..49,50 cycles
tERR(nper) tERR(nper)min = (1 + 0.68ln(n)) * tJIT(per)min
tERR(nper)max = (1 + 0.68ln(n)) * tJIT(per)max ps
Data Timing
DQS, DQS to DQ skew, per
group, per access tDQSQ - 85 - 85 ps
DQ output hold time from DQS,
DQS tQH 0.38 - 0.38 - tCK(avg)
DQ low-impedance time from
CK, CK tLZ(DQ) -390 195 -390 195 ps
DQ high-impedance time from
CK, CK tHZ(DQ) - 195 - 195 ps
Data setup time to DQS, DQS referenced to Vih(ac) / Vil(ac) levels
tDS(base)
DDR3-1866 (AC135)
68 - - - ps
tDS(base)
DDR3L-1866 (AC130)
- - 70 - ps
Data hold time from DQS, DQS referenced to Vih(dc) / Vil(dc) levels
tDH(base)
DC90 - - 75 - ps
DQ and DM Input pulse width for each input
tDIPW 320 - 320 - ps
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 126/141
Parameter Symbol DDR3-1866 DDR3L-1866
Units Min. Max. Min. Max.
Data Strobe Timing
DQS, DQS differential READ
Preamble tRPRE 0.9 Note 19 0.9 Note 19 tCK(avg)
DQS, DQS differential READ
Postamble tRPST 0.3 Note 11 0.3 Note 11 tCK(avg)
DQS, DQS differential output
high time tQSH 0.4 - 0.4 - tCK(avg)
DQS, DQS differential output low
time tQSL 0.4 - 0.4 - tCK(avg)
DQS, DQS differential WRITE
Preamble tWPRE 0.9 - 0.9 - tCK(avg)
DQS, DQS differential WRITE
Postamble tWPST 0.3 - 0.3 - tCK(avg)
DQS, DQS rising edge output
access time from rising CK, CK tDQSCK -195 195 -195 195 ps
DQS and DQS low-impedance
time (Referenced from RL-1) tLZ(DQS) -390 195 -390 195 ps
DQS and DQS high-impedance
time (Referenced from RL+BL/2) tHZ(DQS) - 195 - 195 ps
DQS, DQS differential input low
pulse width tDQSL 0.45 0.55 0.45 0.55 tCK(avg)
DQS, DQS differential input high
pulse width tDQSH 0.45 0.55 0.45 0.55 tCK(avg)
DQS, DQS rising edge to CK,
CK rising edge tDQSS -0.27 0.27 -0.27 0.27 tCK(avg)
DQS, DQS falling edge setup
time to CK, CK rising edge tDSS 0.18 - 0.18 - tCK(avg)
DQS, DQS falling edge hold time
from CK, CK rising edge tDSH 0.18 - 0.18 - tCK(avg)
Command and Address Timing
DLL locking time tDLLK 512 - 512 - nCK
Internal READ Command to PRECHARGE Command delay
tRTP tRTPmin.: max(4tCK, 7.5ns)
tRTPmax. -
Delay from start of internal write transaction to internal read command
tWTR tWTRmin.: max(4tCK, 7.5ns)
tWTRmax.: -
WRITE recovery time tWR 15 - 15 - ns
Mode Register Set command cycle time
tMRD 4 - 4 - nCK
Mode Register Set command update delay
tMOD tMODmin.: max(12tCK, 15ns)
tMODmax.: -
ACT to internal read or write delay time
tRCD
Refer to “Fundamental AC Specifications”
PRE command period tRP
ACT to ACT or REF command period
tRC
ACTIVE to PRECHARGE command period
tRAS
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 127/141
Parameter Symbol DDR3-1866 DDR3L-1866
Units Min. Max. Min. Max.
CAS to CAS command delay tCCD 4 - 4 - nCK
Auto precharge write recovery + precharge time
tDAL(min) WR + roundup(tRP / tCK(avg)) nCK
Multi-Purpose Register Recovery Time
tMPRR 1 - 1 - nCK
ACTIVE to ACTIVE command period for 2KB page size
tRRD max(4tCK,
6ns) - max(4tCK, 6ns) -
Four activate window for 2KB page size
tFAW 35 - 35 - ns
Command and Address setup
time to CK, CK referenced to
Vih(ac) / Vil(ac) levels
tIS(base)
DDR3L-1866
(AC135)
- - 65 - ps
tIS(base)
DDR3(L)-
1866
(AC125)
150 - 150 - ps
Command and Address hold time
from CK, CK referenced to
Vih(dc) / Vil(dc) levels
tIH(base) DDR3 DC100
100 - - - ps
tIH(base) DDR3L DC90
- - 110 - ps
Control and Address Input pulse width for each input
tIPW 535 - 535 - ps
Calibration Timing
Power-up and RESET calibration time
tZQinit tZQinit, min: max(512 tCK, 640ns)
tZQinit, max: -
Normal operation Full calibration time
tZQoper tZQoper, min: max(256 tCK, 320ns)
tZQoper, max: -
Normal operation Short calibration time
tZQCS tZQCSmin: max(64 tCK, 80ns)
tZQCSmax: -
Reset Timing
Exit Reset from CKE HIGH to a valid command
tXPR tXPRmin: max(5 tCK, tRFC(min) + 10ns)
tXPRmax: -
Self Refresh Timings
Exit Self Refresh to commands not requiring a locked DLL
tXS tXSmin: max(5 tCK, tRFC(min) + 10ns)
tXSmax: -
Exit Self Refresh to commands requiring a locked DLL
tXSDLL tXSDLLmin: tDLLK(min)
tXSDLLmax: - nCK
Minimum CKE low width for Self Refresh entry to exit timing
tCKESR tCKESRmin: tCKE(min) + 1 tCK
tCKESRmax: -
Valid Clock Requirement after Self Refresh Entry (SRE) or Power-Down Entry (PDE)
tCKSRE tCKSREmin: max(5 tCK, 10 ns)
tCKSREmax: -
Valid Clock Requirement before Self Refresh Exit (SRX) or Power-Down Exit (PDX) or Reset Exit
tCKSRX tCKSRXmin: max(5 tCK, 10 ns)
tCKSRXmax: -
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 128/141
Parameter Symbol DDR3-1866 DDR3L-1866
Units Min. Max. Min. Max.
Power Down Timings
Exit Power Down with DLL on to any valid command; Exit Precharge Power Down with DLL frozen to commands not requiring a locked DLL
tXP max(3tCK, 6ns) - max(3tCK, 6ns) -
CKE minimum pulse width tCKE max(3tCK, 5ns) - max(3tCK, 5ns) -
Exit Precharge Power Down with DLL frozen to commands requiring a locked DLL
tXPDLL tXPDLLmin: max(10 tCK, 24ns)
tXPDLLmax: -
Command pass disable delay tCPDED tCPDEDmin: 2 tCPDEDmax: -
nCK
Power Down Entry to Exit Timing tPD tPDmin: tCKE(min) tPDmax: 9*tREFI
Timing of ACT command to Power Down entry
tACTPDEN tACTPDENmin: 1 tACTPDENmax: -
nCK
Timing of PRE or PREA command to Power Down entry
tPRPDEN tPRPDENmin: 1 tPRPDENmax: -
nCK
Timing of RD/RDA command to Power Down entry
tRDPDEN tRDPDENmin: RL+4+1
tRDPDENmax: - nCK
Timing of WR command to Power Down entry (BL8OTF, BL8MRS, BC4OTF)
tWRPDEN tWRPDENmin: WL + 4 + (tWR / tCK(avg))
tWRPDENmax: - nCK
Timing of WRA command to Power Down entry (BL8OTF, BL8MRS, BC4OTF)
tWRAPDEN tWRAPDENmin: WL+4+WR+1
tWRAPDENmax: - nCK
Timing of WR command to Power Down entry (BC4MRS)
tWRPDEN tWRPDENmin: WL + 2 + (tWR / tCK(avg))
tWRPDENmax: - nCK
Timing of WRA command to Power Down entry (BC4MRS)
tWRAPDEN tWRAPDENmin: WL + 2 +WR + 1
tWRAPDENmax: - nCK
Timing of REF command to Power Down entry
tREFPDEN tREFPDENmin: 1 tREFPDENmax: -
nCK
Timing of MRS command to Power Down entry
tMRSPDEN tMRSPDENmin: tMOD(min)
tMRSPDENmax: -
ODT Timings
ODT turn on Latency ODTLon WL-2=CWL+AL-2 nCK
ODT turn off Latency ODTLoff WL-2=CWL+AL-2 nCK
ODT high time without write command or with write command and BC4
ODTH4 ODTH4min: 4 ODTH4max: -
nCK
ODT high time with Write command and BL8
ODTH8 ODTH8min: 6 ODTH8max: -
nCK
Asynchronous RTT turn-on delay (Power-Down with DLL frozen)
tAONPD 2 8.5 2 8.5 ns
Asynchronous RTT turn-off delay (Power-Down with DLL frozen)
tAOFPD 2 8.5 2 8.5 ns
RTT turn-on tAON -195 195 -195 195 ps
RTT_Nom and RTT_WR turn-off time from ODTLoff reference
tAOF 0.3 0.7 0.3 0.7 tCK(avg)
RTT dynamic change skew tADC 0.3 0.7 0.3 0.7 tCK(avg)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 129/141
Parameter Symbol DDR3-1866 DDR3L-1866
Units Min. Max. Min. Max.
Write Leveling Timings
First DQS/ DQS rising edge after
write leveling mode is programmed
tWLMRD 40 - 40 - nCK
DQS/ DQS delay after write
leveling mode is programmed tWLDQSEN 25 - 25 - nCK
Write leveling setup time from
rising CK, CK crossing to rising
DQS, DQS crossing
tWLS 140 - 140 - ps
Write leveling hold time from
rising DQS, DQS crossing to
rising CK, CK crossing
tWLH 140 - 140 - ps
Write leveling output delay tWLO 0 7.5 0 7.5 ns
Write leveling output error tWLOE 0 2 0 2 ns
Jitter Notes
1. Unit “tCK(avg)” represents the actual tCK(avg) of the input clock under operation. Unit “nCK” represents one clock cycle of the input clock, counting the actual clock edges. Ex) tMRD=4 [nCK] means; if one Mode Register Set command is registered at Tm, anther Mode Register Set command may be registered at Tm+4, even if (Tm+4-Tm) is 4 x tCK(avg) + tERR(4per), min.
2. These parameters are measured from a command/address signal (CKE, CS , RAS , CAS , WE , ODT, BA0, A0, A1, etc)
transition edge to its respective clock signal (CK/ CK ) crossing. The spec values are not affected by the amount of clock
jitter applied (i.e. tJIT(per), tJIT(cc), etc.), as the setup and hold are relative to the clock signal crossing that latches the command/address. That is, these parameters should be met whether clock jitter is present or not.
3. These parameters are measured from a data strobe signal (DQS(L/U), DQS(L/U)) crossing to its respective clock signal
(CK, CK ) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT(per), tJIT(cc), etc), as
these are relative to the clock signal crossing. That is, these parameters should be met whether clock jitter is present or not. 4. These parameters are measured from a data signal (DM(L/U), DQ(L/U)0, DQ(L/U)1, etc.) transition edge to its respective
data strobe signal (DQS(L/U), DQS(L/U)) crossing.
5. For these parameters, the DDR3(L) SDRAM device supports tnPARAM [nCK] = RUtPARAM[ns] / tCK(avg)[ns], which is in clock cycles, assuming all input clock jitter specifications are satisfied.
6. When the device is operated with input clock jitter, this parameter needs to be derated by the actual tERR(mper), act of the input clock, where 2 <= m <=12. (Output derating is relative to the SDRAM input clock.)
7. When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT(per),act of the input clock. (Output deratings are relative to the SDRAM input clock.)
Timing Parameter Notes
1. Actual value dependent upon measurement level definitions which are TBD. 2. Commands requiring a locked DLL are: READ ( and RAP) are synchronous ODT commands. 3. The max values are system dependent. 4. WR as programmed in mode register. 5. Value must be rouned-up to next higher integer value. 6. There is no maximum cycle time limit besides the need to satisfy the refresh interval, tREFI. 7. For definition of RTT-on time tAON See “Timing Parameters”. 8. For definition of RTT-off time tAOF See “Timing Parameters”. 9. tWR is defined in ns, for calculation of tWRPDEN it is necessary to round up tWR/tCK to the next integer. 10. WR in clock cycles are programmed in MR0. 11. The maximum read postamble is bounded by tDQSCK(min) plus tQSH(min) on the left side and tHZ(DQS)max on the right
side. 12. Output timing deratings are relative to the SDRAM input clock. When the device is operated with input clock jitter, this
parameter needs to be derated by TBD.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 130/141
13. Value is only valid for RON34. 14. Single ended signal parameter. 15. tREFI depends on TOPER.
16. tIS(base) and tIH(base) values are for 1V/ns CMD/ADD single-ended slew rate and 2V/ns CK, CK differential slew rate.
Note for DQ and DM signals, VREF(DC)=VREFDQ(DC). For input only pins except RESET, VREF(DC)=VREFCA(DC).
17. tDS(base) and tDH(base) values are for 1V/ns DQ single-ended slew rate and 2V/ns DQS, DQS differential slew rate.
Note for DQ and DM signals, VREF(DC)=VREFDQ(DC). For input only pins except RESET, VREF(DC)=VREFCA(DC). 18. Start of internal write transaction is defined as follows:
For BL8 (fixed by MRS and on-the-fly): Rising clock edge 4 clock cycles after WL. For BC4 (on-the-fly): Rising clock edge 4 clock cycles after WL. For BC4 (fixed by MRS): Rising clock edge 2 clock cycles after WL.
19. The maximum preamble is bound by tLZ (DQS) max on the left side and tDQSCK(max) on the right side. 20. CKE is allowed to be registered low while operations such as row activation, precharge, autoprecharge or refresh are in
progress, but power-down IDD spec will not be applied until finishing those operations. 21. Although CKE is allowed to be registered LOW after a REFRESH command once tREFPDEN(min) is satisfied, there are
cases where additional time such as tXPDLL(min) is also required. 22. Defined between end of MPR read burst and MRS which reloads MPR or disables MPR function. 23. One ZQCS command can effectively correct a minimum of 0.5% (ZQCorrection) of RON and RTT impedance error within 64
nCK for all speed bins assuming the maximum sensitivities specified in the “Output Driver Voltage and Temperature Sensitivity” and “ODT Voltage and Temperature Sensitivity” tables. The appropriate interval between ZQCS commands can be determined from these tables and other application-specific parameters.
One method for calculating the interval between ZQCS commands, given the temperature (Tdriftrate) and voltage (Vdriftrate) drift rates that the SDRAM is subject to in the application, is illustrated. The interval could be defined by the following formula: ZQCorrection / [(Tsens x Tdriftrate) + (Vsens x Vdriftrate)] where Tsens = max(dRTTdT, dRONdTM) and Vsens = max(dRTTdV, dRONdVM) define the SDRAM temperature and voltage sensitivities.
For example, if Tsens = 1.5%/C, Vsens = 0.15%/Mv, Tdriftrate = 1 C/sec and Vdriftrate = 15Mv/sec, then the interval between ZQCS commands is calculated as 0.5 / [(1.5x1)+(0.15x15)] = 0.133 ~ 128ms
24. n = from 13 cycles to 50 cycles. This row defines 38 parameters. 25. tCH(abs) is the absolute instantaneous clock high pulse width, as measured from one rising edge to the following falling
edge. 26. tCL(abs) is the absolute instantaneous clock low pulse width, as measured from one falling edge to the following rising edge. 27. The tIS(base) AC150 specifications are adjusted from the tIS(base) specification by adding an additional 100ps of derating
to accommodate for the lower altemate threshold of 150mV and another 25ps to account for the earlier reference point [(175mV – 150mV) / 1V/ns].
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 131/141
Address / Command Setup, Hold, and Derating
For all input signals the total tIS (setup time) and tIH (hold time) required is calculated by adding the data sheet tIS(base) and tIH(base) and tIH(base) value to the delta tIS and delta tIH derating value respectively.
Example: tIS (total setup time) = tIS(base) + delta tIS
Setup (tIS) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VREF(dc) and the first crossing of VIH(ac)min. Setup (tIS) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of VREF(dc) and the first crossing of VIL(ac)max. If the actual signal is always earlier than the nominal slew rate line between shaded ‘VREF (dc) to ac region’, use nominal slew rate for derating value. If the actual signal is later than the nominal slew rate line anywhere between shaded ‘VREF(dc) to ac region’, the slew rate of the tangent line to the actual signal from the ac level to dc level is used for derating value.
Hold (tIH) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VIL(dc)max and the first crossing of VREF(dc). Hold (tIH) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of VIH(dc)min and the first crossing of VREF(dc). If the actual signal is always later than the nominal slew rate line between shaded ‘dc to VREF(dc) region’, use nominal slew rate for derating value. If the actual signal is earlier than the nominal s lew rate line any-where between shaded ‘dc to VREF(dc) region’, the slew rate of a tangent line to the actual signal from the dc level to VREF(dc) level is used for derating value. For a valid transition the input signal has to remain above/below VIH/IL(ac) for some time tVAC. Although for slow slew rates the total setup time might be negative (i.e. a valid input signal will not have reached VIH/IL(ac) at the time of the rising clock transition) a valid input signal is still required to complete the transition and reach VIH/IL(ac).
ADD/CMD Setup and Hold Base-Values for 1V/ns
Symbol Reference DDR3-1600 DDR3L-1600 DDR3-1866 DDR3L-1866 Units
tIS(base) AC175 VIH/L(ac) 45 - - - ps
tIS(base) AC160 VIH/L(ac) - 60 - - ps
tIS(base) AC150 VIH/L(ac) 170 - - - ps
tIS(base) AC135 VIH/L(ac) - 185 65 65 ps
tIS(base) AC125 VIH/L(ac) - - 150 150 ps
ftIH(base) DC100 VIH/L(dc) 120 - 100 - ps
ftIH(base) DC90 VIH/L(dc) - 130 - 110 ps
Note: AC/DC referenced for 1V/ns Address/Command slew rate and 2V/ns differential CK- CK slew rate.
Derating values DDR3-1600 tIS/tIH – AC/DC based AC175 Threshold
tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH
2 88 50 88 50 88 50 96 58 104 66 112 74 120 84 128 100
1.5 59 34 59 34 59 34 67 42 75 50 83 58 91 68 99 84
1 0 0 0 0 0 0 8 8 16 16 24 24 32 34 40 50
0.9 -2 -4 -2 -4 -2 -4 6 4 14 12 22 20 30 30 38 46
0.8 -6 -10 -6 -10 -6 -10 2 -2 10 6 18 14 26 24 34 40
0.7 -11 -16 -11 -16 -11 -16 -3 -5 5 0 13 8 21 18 29 34
0.6 -17 -26 -17 -26 -17 -26 -9 -18 -1 -10 7 -2 15 8 23 24
0.5 -35 -40 -35 -40 -35 -40 -27 -32 -19 -24 -11 -16 -2 -6 5 10
0.4 -62 -60 -62 -60 -62 -60 -54 -37 -46 -44 -38 -36 -30 -26 -22 -10
AC 160 Thresold -> VIH(ac) = VREF(dc) + 175mV, VIL(ac) = VREF(dc) - 175mV
2.0 V/ns 1.8 V/ns 1.6 V/ns 1.4 V/ns 1.0 V/ns1.2 V/ns
CM
D/A
DD
Sle
w r
ate
(V
/ns)
4.0 V/ns 3.0 V/ns
CK, /CK Differential Slew Rate
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 132/141
Derating values DDR3-1600 tIS/tIH –AC/DC based AC150 Threshold
Derating values DDR3L-1600 tIS/tIH – AC/DC based AC160 Threshold
Derating values DDR3L-1600 tIS/tIH –AC/DC based AC135 Threshold
tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH
2 75 50 75 50 75 50 83 58 91 66 99 74 107 84 115 100
1.5 50 34 50 34 50 34 58 42 66 50 74 58 82 68 90 84
1 0 0 0 0 0 0 8 8 16 16 24 24 32 34 40 50
0.9 0 -4 0 -4 0 -4 8 4 16 12 24 20 32 30 40 46
0.8 0 -10 0 -10 0 -10 8 -2 16 6 24 14 32 24 40 40
0.7 0 -16 0 -16 0 -16 8 -8 16 0 24 8 32 18 40 34
0.6 -1 -26 -1 -26 -1 -26 7 -18 15 -10 23 -2 31 8 39 24
0.5 -10 -40 -10 -40 -10 -40 -2 -32 6 -24 14 -16 22 -6 30 10
0.4 -25 -60 -25 -60 -25 -60 -17 -52 -9 -44 -1 -36 7 -26 15 5
CM
D/A
DD
Sle
w r
ate
(V
/ns)
4.0 V/ns 3.0 V/ns
CK,/CK Differential Slew Rate
AC135 Thresold -> VIH(AC) = VREF(DC) + 150mV, VIL(AC)= VREF(DC) - 150mV
2.0 V/ns 1.8 V/ns 1.6 V/ns 1.4 V/ns 1.0 V/ns1.2 V/ns
tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH
2 68 45 68 45 68 45 76 53 84 61 92 69 100 79 108 95
1.5 45 30 45 30 45 30 53 38 61 46 69 54 77 64 85 80
1 0 0 0 0 0 0 8 8 16 16 24 24 32 34 40 50
0.9 2 -3 2 -3 2 -3 10 5 18 13 26 21 34 31 42 47
0.8 3 -8 3 -8 3 -8 11 1 19 9 27 17 35 27 43 43
0.7 6 -13 6 -13 6 -13 14 -5 22 3 30 11 38 21 46 37
0.6 9 -20 9 -20 9 -20 17 -12 25 -4 33 4 41 14 49 30
0.5 5 -30 5 -30 5 -30 13 -22 21 -14 29 -6 37 4 45 20
0.4 -3 -45 -3 -45 -3 -45 6 -37 14 -29 22 -21 30 -11 38 5
CM
D/A
DD
Sle
w r
ate
(V
/ns)
4.0 V/ns 3.0 V/ns
CK,/CK Differential Slew Rate
AC135 Thresold -> VIH(AC) = VREF(DC) + 135mV, VIL(AC)= VREF(DC) - 135mV
2.0 V/ns 1.8 V/ns 1.6 V/ns 1.4 V/ns 1.0 V/ns1.2 V/ns
tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH
2 80 45 80 45 80 45 88 53 96 61 104 69 112 79 120 95
1.5 53 30 53 30 53 30 61 38 69 46 77 54 85 64 93 80
1 0 0 0 0 0 0 8 8 16 16 24 24 32 34 40 50
0.9 -1 -3 -1 -3 -1 -3 7 5 15 13 23 21 31 31 39 47
0.8 -3 -8 -3 -8 -3 -8 5 1 13 9 21 17 29 27 37 43
0.7 -5 -13 -5 -13 -5 -13 3 -5 11 3 19 11 27 21 35 37
0.6 -8 -20 -8 -20 -8 -20 0 -12 8 -4 16 4 24 14 32 30
0.5 20 -30 -20 -30 -20 -30 -12 -22 -4 -14 4 -6 12 4 20 20
0.4 -40 -45 -40 -45 -40 -45 -32 -37 -24 -29 -16 -21 -8 -11 0 5
CM
D/A
DD
Sle
w r
ate
(V
/ns)
4.0 V/ns 3.0 V/ns
CK, /CK Differential Slew Rate
AC 160 Thresold -> VIH(ac) = VREF(dc) + 160mV, VIL(ac) = VREF(dc) - 160mV
2.0 V/ns 1.8 V/ns 1.6 V/ns 1.4 V/ns 1.0 V/ns1.2 V/ns
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 133/141
Derating values DDR3-1866 tIS/tIH – AC/DC based AC135 Threshold
Derating values DDR3-1866 tIS/tIH –AC/DC based AC125 Threshold
Derating values DDR3L-1866 tIS/tIH – AC/DC based AC125 Threshold
AC 125 Threshold -> VIH (ac) = VREF (dc) + 125mV, VIL (ac) = VREF(dc) - 125mV
CK,/CK Differential Slew Rate
4.0 V/ns 3.0 V/ns 2.0 V/ns 1.8 V/ns 1.6 V/ns 1.4 V/ns 1.2 V/ns 1.0 V/ns
tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH
CM
D/A
DD
Sle
w r
ate
(V
/ns)
2 63 45 63 45 63 45 71 53 79 61 87 69 95 79 103 95
1.5 42 30 42 30 42 30 50 38 58 46 66 54 74 64 82 80
1 0 0 0 0 0 0 8 8 16 16 24 24 32 34 40 50
0.9 3 -3 3 -3 3 -3 11 5 19 13 27 21 35 31 43 47
0.8 6 -8 6 -8 6 -8 14 1 22 9 30 17 38 27 46 43
0.7 10 -13 10 -13 10 -13 18 -5 26 3 34 11 42 21 50 37
0.6 16 -20 16 -20 16 -20 24 -12 32 4 40 -4 48 14 56 30
0.5 15 -30 15 -30 15 -30 23 -22 31 -14 39 -6 47 4 55 20
0.4 13 -45 13 -45 13 -45 21 -37 29 -29 37 -21 45 -11 53 5
tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH
2 68 50 68 50 68 50 76 58 84 66 92 74 100 84 108 100
1.5 45 34 45 34 45 34 53 42 61 50 69 58 77 68 85 84
1 0 0 0 0 0 0 8 8 16 16 24 24 32 34 40 50
0.9 2 -4 2 -4 2 -4 10 4 18 12 26 20 34 30 42 46
0.8 3 -10 3 -10 3 -10 11 -2 19 6 27 14 35 24 43 40
0.7 6 -16 6 -16 6 -16 14 -8 22 0 30 8 38 18 46 34
0.6 9 -26 9 -26 9 -26 17 -18 25 -10 33 -2 41 8 49 24
0.5 5 -40 5 -40 5 -40 13 -32 21 -24 29 -16 37 -6 45 10
0.4 -3 -60 -3 -60 -3 -60 6 -52 14 -44 22 -36 30 -26 38 -10CM
D/A
DD
Sle
w r
ate
(V
/ns)
4.0 V/ns 3.0 V/ns
CK,/CK Differential Slew Rate
AC 135 Threshold -> VIH (ac) = VREF (dc) + 135mV, VIL (ac) = VREF(dc) - 135mV
2.0 V/ns 1.8 V/ns 1.6 V/ns 1.4 V/ns 1.0 V/ns1.2 V/ns
tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH tIS tIH
2 63 50 63 50 63 50 71 58 79 66 87 74 95 84 103 100
1.5 42 34 42 34 42 34 50 42 58 50 66 58 74 68 82 84
1 0 0 0 0 0 0 8 8 16 16 24 24 32 34 40 50
0.9 4 -4 4 -4 4 -4 12 4 20 12 28 20 36 30 44 46
0.8 6 -10 6 -10 6 -10 14 -2 22 6 30 14 38 24 46 40
0.7 11 -16 11 -16 11 -16 19 -8 27 0 35 8 43 18 51 34
0.6 16 -26 16 -26 16 -26 24 -18 32 -10 40 -2 48 8 56 24
0.5 15 -40 15 -40 15 -40 23 -32 31 -24 39 -16 47 -6 55 10
0.4 13 -60 13 -60 13 -60 21 -52 29 -44 37 -36 45 -26 53 -10CM
D/A
DD
Sle
w r
ate
(V
/ns)
4.0 V/ns 3.0 V/ns
CK,/CK Differential Slew Rate
AC 125 Threshold -> VIH (ac) = VREF (dc) + 125mV, VIL (ac) = VREF(dc) - 125mV
2.0 V/ns 1.8 V/ns 1.6 V/ns 1.4 V/ns 1.0 V/ns1.2 V/ns
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 134/141
Required time tVAC above VIH(AC) below VIL(AC) for ADD/CMD transition (DDR3(L)-1600)
Slew Rate [V/ns] DDR3-1600 DDR3L-1600
175mV [ps] 150mV [ps] 160mV [ps] 135mV [ps]
>2.0 75 175 200 213
2 57 170 200 213
1.5 50 167 173 190
1 38 130 120 145
0.9 34 113 102 130
0.8 29 93 80 111
0.7 22 66 51 87
0.6 Note 30 13 55
0.5 Note Note Note 10
<0.5 Note Note Note 10
Note: Rising input signal shall become equal to or greater than VIH(ac) level and falling input signal shall become equal to or less than VIL(ac) level.
Required time tVAC above VIH(AC) below VIL(AC) for ADD/CMD transition (DDR3(L)-1866)
Slew Rate [V/ns] DDR3-1866 DDR3L-1866
135mV [ps] 125mV [ps] 135mV [ps] 125mV [ps]
>2.0 168 173 200 205
2 168 173 200 205
1.5 145 152 178 184
1 100 110 133 143
0.9 85 96 118 129
0.8 66 79 99 111
0.7 42 56 75 89
0.6 10 27 43 59
0.5 Note Note Note 18
<0.5 Note Note Note 18
Note: Rising input signal shall become equal to or greater than VIH(ac) level and falling input signal shall become equal to or less than VIL(ac) level.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 135/141
Data Setup, Hold, and Slew Rate De-rating
For all input signals the total tDS (setup time) and tDH (hold time) required is calculated by adding the data sheet tDH(base) and tDH(base) value to the delta tDS and delta tDH derating value respectively.
Example: tDS (total setup time) = tDS(base) + delta tDS
Setup (tDS) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VREF(dc) and the first crossing of VIH(ac)min. Setup (tDS) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of VREF(dc) and the first crossing of VIL(ac)max. If the actual signal is always earlier than the nominal slew rate line between shaded ‘VREF(dc) to ac region’, use nominal slew rate for derating value. If the actual signal is later than the nominal slew rate line anywhere between shaded ‘VREF(dc) to ac region’, the slew rate of the tangent line to the actual signal from the ac level to dc level is used for derating value.
Hold (tDH) nominal slew rate for a rising signal is defined as the slew rate between the last crossing of VIL(dc)max and the first crossing of VREF(dc). Hold (tDH) nominal slew rate for a falling signal is defined as the slew rate between the last crossing of VIH(dc)min and the first crossing of VREF(dc). If the actual signal is always later than the nominal slew rate line between shaded ‘dc level to VREF(dc) region’, use nominal slew rate for derating value. If the actual signal is earlier than the nominal slew rate line anywhere between shaded ‘dc to VREF(dc) region’, the slew rate of a tangent line to the actual signal from the dc level to VREF(dc) level is used for derating value.
For a valid transition the input signal has to remain above/below VIH/IL(ac) for some time tVAC. Although for slow slew rates the total setup time might be negative (i.e. a valid input signal will not have reached VIH/IL(ac) at the time of the rising clock transition) a valid input signal is still required to complete the transition and reach VIH/IL(ac). For slew rates in between the values listed in the following tables, the derating values may be obtained by linear interpolation. These values are typically not subject to production test. They are verified by design and characterization.
Derating values DDR3-1600 tDS/tDH – AC/DC based AC150/ Threshold
Note: Cell contents shaded in gray are defined as ‘not supported’.
Derating values DDR3L-1600 tDS/tDH – AC/DC based AC135/ Threshold
Note: Cell contents shaded in gray are defined as ‘not supported’.
tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH
2 75 50 75 50 75 50 - - - - - - - - - -
1.5 50 34 50 34 50 34 58 42 - - - - - - - -
1 0 0 0 0 0 0 8 8 16 16 - - - - - -
0.9 - - 0 -4 0 -4 8 4 16 12 24 20 - - - -
0.8 - - - - 0 -10 8 -2 16 6 24 14 32 24 - -
0.7 - - - - - - 8 -8 16 0 24 8 32 18 40 34
0.6 - - - - - - - - 15 -10 23 -2 31 8 39 24
0.5 - - - - - - - - - - 14 -16 22 -6 30 10
0.4 - - - - - - - - - - - - 7 -26 15 -10
DQ
Sle
w r
ate
(V
/ns)
4.0 V/ns 3.0 V/ns
DQS, /DQS Differential Slew Rate
AC150 Threshold
2.0 V/ns 1.8 V/ns 1.6 V/ns 1.4 V/ns 1.0 V/ns1.2 V/ns
tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH
2 45 68 45 68 45 - - - - - - - - - - -
1.5 45 30 45 30 45 30 53 38 - - - - - - - -
1 0 0 0 0 0 0 8 8 16 16 - - - - - -
0.9 - - 2 -3 2 -3 10 5 18 13 26 21 - - - -
0.8 - - - - 3 -8 11 1 19 9 27 17 35 27 - -
0.7 - - - - - - 14 -5 22 3 30 11 38 21 46 37
0.6 - - - - - - - - 25 -4 33 4 41 14 49 30
0.5 - - - - - - - - - - 29 -6 37 4 45 20
0.4 - - - - - - - - - - - - 30 -11 38 5
DQ
Sle
w r
ate
(V
/ns)
4.0 V/ns 3.0 V/ns
DQS, /DQS Differential Slew Rate
AC135 Threshold -> VIH(AC) = VREF(DC) + 135mV, VIL(AC)= VREF(DC) - 135mV
2.0 V/ns 1.8 V/ns 1.6 V/ns 1.4 V/ns 1.0 V/ns1.2 V/ns
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 136/141
Derating values DDR3-1600 tDS/tDH – AC/DC based AC135 Threshold
Derating values DDR3-1866 tDS/tDH – AC/DC based AC135 Threshold
Note: Cell contents shaded in gray are defined as ‘not supported’.
tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH
4 34 25 34 25 34 25 - - - - - - - - - - - - - - - - - -
3.5 29 21 29 21 29 21 29 21 - - - - - - - - - - - - - - - -
3 23 17 23 17 23 17 23 17 23 17 - - - - - - - - - - - - - -
2.5 - - 14 10 14 10 14 10 14 10 14 10 - - - - - - - - - - - -
2 - - - - 0 0 0 0 0 0 0 0 0 0 - - - - - - - - - -
1.5 - - - - - - -23 -17 -23 -17 -23 -17 -23 -17 -15 -9 - - - - - - - -
1 - - - - - - - - -68 -50 -68 -50 -68 -50 -60 -42 -52 -34 - - - - - -
0.9 - - - - - - - - - - -66 -54 -66 -54 -58 -46 -50 -38 -42 -30 - - - -
0.8 - - - - - - - - - - - - -64 -60 -56 -52 -48 -44 -40 -36 -32 -26 - -
0.7 - - - - - - - - - - - - - - -53 -59 -45 -51 -37 -43 -29 -33 -21 -17
0.6 - - - - - - - - - - - - - - - - -43 -61 -35 -53 -27 -43 -19 -27
0.5 - - - - - - - - - - - - - - - - - - -39 -66 -31 -56 -23 -40
0.4 - - - - - - - - - - - - - - - - - - - - -38 -76 -30 -60
2.0 V/ns 1.8 V/ns 1.6 V/ns 1.4 V/ns 1.0 V/ns1.2 V/ns
AC 135 Threshold -> VIH (ac) = VREF (dc) + 135mV, VIL (ac) = VREF(dc) - 135mV
DC 100 Threshold -> VIH (dc) = VREF (dc) + 100mV, VIL (dc) = VREF(dc) - 100mV
4.0 V/ns 3.0 V/ns5.0 V/ns6.0 V/ns7.0 V/ns8.0 V/ns
DQ
Sle
w r
ate
(V
/ns)
DQS, /DQS Differential Slew Rate
tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH tDS tDH
2 68 50 68 50 68 50 - - - - - - - - - -
1.5 45 34 45 34 45 34 53 42 - - - - - - - -
1 0 0 0 0 0 0 8 8 16 16 - - - - - -
0.9 - - 2 -4 2 -4 10 4 18 12 26 20 - - - -
0.8 - - - - 3 -10 11 -2 19 6 27 14 35 24 - -
0.7 - - - - - - 14 -8 22 0 30 8 38 18 46 34
0.6 - - - - - - - - 25 -10 33 -2 41 8 49 24
0.5 - - - - - - - - - - 29 -16 37 -6 45 10
0.4 - - - - - - - - - - - - 30 -26 38 -10
AC 135 Threshold -> VIH (ac) = VREF (dc) + 135mV, VIL (ac) = VREF(dc) - 135mV
DC 100 Threshold -> VIH (dc) = VREF (dc) + 100mV, VIL (dc) = VREF(dc) - 100mV
DQS, /DQS Differential Slew Rate
DQ
Sle
w r
ate
(V
/ns)
1.0 V/ns1.2 V/ns4.0 V/ns 3.0 V/ns 2.0 V/ns 1.8 V/ns 1.6 V/ns 1.4 V/ns
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 137/141
Required time tVAC above VIH(ac) below VIL(ac) for valid DQ transition
Slew Rate
[V/ns]
DDR3-1600 DDR3L-1600 DDR3-1866 DDR3L-1866
150mV[ps] 135mV[ps] 135mV[ps] 135mV[ps] 130mV[ps]
>2.0 105 113 113 93 95
2 105 113 113 93 95
1.5 80 90 90 70 73
1 30 45 45 25 16
0.9 13 30 30 Note Note
0.8 Note 11 11 Note
0.7 Note Note Note -
0.6 Note Note Note -
0.5 Note Note Note -
<0.5 Note Note Note -
Note: Rising input signal shall become equal to or greater than VIH(ac) level and falling input signal shall become equal to or
less than VIL(ac) level.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 138/141
PACKING DIMENSIONS 96-BALL DDR3(L) SDRAM ( 7.5x13.5 mm )
e
D1
D
EE
1
"A"
PIN #1
SEATING PLANE
DETAIL : "A"
CAVITY
A
SOLDER BALL
A1
ob
Index
PIN #1Index
Symbol Dimension in mm Dimension in inch
Min Norm Max Min Norm Max
A - -
1.00 -
-
0.039
A1 0.30 0.35 0.40 0.012 0.014
0.016
Φb 0.40 0.45 0.50 0.016 0.018 0.020
D 7.40 7.50 7.60 0.291 0.295 0.299
E 13.40 13.50 13.60 0.528 0.531 0.535
D1 6.40 BSC
0.252 BSC
E1 12.00 BSC
0.472 BSC
e 0.80 BSC
0.031 BSC
Controlling dimension : Millimeter.
(Revision date : Sep 22 2015)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 139/141
PACKING DIMENSIONS 96-BALL DDR SDRAM ( 7.5x13 mm )
e
D1
D
EE
1
"A"
Pin# A1
SEATING PLANE
DETAIL : "A"
A
SOLDER BALL
A1
IndexSide
Pin# A1Index
"B"
Pin# A1Index
DETAIL : "B"
bo
Symbol Dimension in mm Dimension in inch
Min Norm Max Min Norm Max
A
1.00
0.039
A1 0.30 0.35 0.40 0.012 0.014
0.016
Φb 0.40 0.45 0.50 0.016 0.018 0.020
D 7.40 7.50 7.60 0.291 0.295 0.299
E 12.90 13.00 13.10 0.508 0.512 0.516
D1 6.40 BSC
0.252 BSC
E1 12.00 BSC
0.472 BSC
e 0.80 BSC
0.031 BSC
Controlling dimension : Millimeter.
(Revision date : Nov172 2017)
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 140/141
Revision History
Revision Date Description
0.1 2017.10.25 Original
0.2 2017.12.19 Add 96 ball BGA packing (7.5x13x1mm)
1.0 2018.07.12
1. Delete Preliminary
2.Add the table of Output Driver DC Electrical Characteristics, ODT DC Electrical Characteristics and Reference Settings for ODT Timing Measurements for DDR3L.
3. Modify IDD3P from 60 to 65mA
4. Revised typo.
ESMT M15T2G16128A (2L) Operation Temperature Condition -40°C~105°C
Elite Semiconductor Memory Technology Inc Publication Date : Jul. 2018 Revision : 1.0 141/141
Important Notice
All rights reserved.
No part of this document may be reproduced or duplicated in any form or by
any means without the prior permission of ESMT.
The contents contained in this document are believed to be accurate at the
time of publication. ESMT assumes no responsibility for any error in this
document, and reserves the right to change the products or specification in
this document without notice.
The information contained herein is presented only as a guide or examples
for the application of our products. No responsibility is assumed by ESMT for
any infringement of patents, copyrights, or other intellectual property rights of
third parties which may result from its use. No license, either express, implied
or otherwise, is granted under any patents, copyrights or other intellectual
property rights of ESMT or others.
Any semiconductor devices may have inherently a certain rate of failure. To
minimize risks associated with customer's application, adequate design and
operating safeguards against injury, damage, or loss from such failure,
should be provided by the customer when making application designs.
ESMT's products are not authorized for use in critical applications such as,
but not limited to, life support devices or system, where failure or abnormal
operation may directly affect human lives or cause physical injury or property
damage. If products described here are to be used for such kinds of
application, purchaser must do its own quality assurance testing appropriate
to such applications.