Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Type series booklet 50 + 60 Hz2746.5/6-10 G2 Etaprime B/BN
Self-priming close-coupled pumps
for pure and contaminated liquids
Fields of applicationWater supply Swimming pool waterFire-fighting systems SeawaterSpray irrigation Fire-fighting waterIrrigation Brackish waterDrainage CondensateAir -conditioning systems BrineDrinking water OilsIndustrial water Cleaning agentsCooling water
Operating data50 Hz 60 Hz
Q up to 100 m3/h (28 l/s) up to 120 m3/h (33 l/s)H up to 85 m up to 90 mp2 up to 10 bar 1) up to 10 bar 1)
H1geo up to 9 m up to 9 mt -30 to +90 �C -30 to +90 �C1) see pressure limits, page 6
DesignHorizontal volute casing pumps, single-stage, with openmulti-vane impeller.On pump sizes 40-140 and above, the shaft is fitted with areplaceable shaft sleeve in the shaft seal area.Etaprime BNPump and motor flanged together to form a close-coupled unit,with standardized motor to DIN 42 677.Pump shaft and motor shaft are rigidly connected.Pump connections to DIN/EN or ASME.Etaprime BPump and motor flanged together to form a close-coupled unit,with common shaft
Shaft sealSingle-acting mechanical seal to EN 12 756.On Etaprime BN, double-acting mechanical seals are possible.
CertificationCertified quality management ISO 9001.
Designation
Type seriesCasing materialShort close-coupled designStub shaft version withstandardized motor
Mechanical seal codeDischarge nozzle DN (code)Nominal impeller dia. (code)Motor rating: kW x 10 (example 4 kW)Number of motor poles
Etaprime G B (BN) 11 50 160 / 40 2
DriveStandard version Etaprime BNSurface-cooled KSB-IEC three-phase squirrel cage motorWinding 50 Hz: up to 2.2 kW 220-240/380-420 V,
4 kW and above: 380-420 /660-725 V,Winding 60 Hz: 440-480 V,Design: 1.1 kW IM B34 1)
up to 4 kW IM V17.5 kW and above IM V15
Enclosure: IP 55Thermal class: F with temperature sensors:
3 PTC thermistorsOperating mode: continuous operation S1orsurface-cooled three-phase squirrel cage motor as describedabove, but West European brand to KSB’s choice1) without temperature sensors, with flange C-120
Standard version Etaprime BSurface-cooled KSB three-phase squirrel cage motor with lon-ger shaft and special flangeWinding: up to 2.2 kW, 230/400 V
4 kW: 400/690 VDesign: IM B5Enclosure: IP 55 or IP 54Thermal class: FOperating mode: continuous operation S1Contact guard: cover plates on drive lantern to EN 294
EP1450.01
5 10 20 30 40 50 100 200 300 400US.gpm
4 5 10 20 30 40 50 100 200 300IM.gpm
0.3 0.4 0.5 1 2 3 4 5 10 20l/s
1 2 3 4 5 10 20 30 40 50 100Q[m /h]3
4
5
10
20
30
40
50
ft
1
2
3
4
5
10
20
25
H[m]
100--240.1 L/BN
80--190 L/BN
80--170 L/BN
65--150 L/BN/B
50--160 L/BN/B
50--130 L/BN/B
40--140 L/BN/B
40--110 L/BN
32--120 L/BN
25--100 L/BN
80--200 L/BN65--180 L/BN
1)
1)
1)
1)
1)
1)
1)
1)1)
1) lieferbar auch in Chrom-Nickel-Molybdänstahlguss1) also available in cast CrNiMo steel1) Egalement disponible en acier moulé au CrNiMo
1) Suministrable también en Acero moldeado al Cr-Ni-Mo1) Ook leverbaar in chroom-nikkel-molybdeenstaal1) Disponibile anche come fusione di acciaio al cromo-nichel-molibdeno
EP2900.01
5 10 20 30 40 50 100 200 300 400 500US.gpm
4 5 10 20 30 40 50 100 200 300 400 500IM.gpm
0.3 0.4 0.5 1 2 3 4 5 10 20 30 40 50l/s
1 2 3 4 5 10 20 30 40 50 100 200Q[m /h]310
20
30
40
50
100
200
ft
3
4
5
10
20
30
40
50
90
H[m]
100--240.1 L/BN80--200 L/BN
80--170 L/BN
65--180 L/BN
32--120 L/BN
25--100 L/BN
80--190 L/BN
65--150 L/BN/B
50--160 L/BN/B
40--140 L/BN/B
40--110 L/BN
50--130 L/BN/B
1)
1)
1)
1)
1)
1)
1)
1)1)
1) lieferbar auch in Chrom-Nickel-Molybdänstahlguss1) also available in cast CrNiMo steel1) Egalement disponible en acier moulé au CrNiMo
1) Suministrable también en Acero moldeado al Cr-Ni-Mo1) Ook leverbaar in chroom-nikkel-molybdeenstaal1) Disponibile anche come fusione di acciaio al cromo-nichel-molibdeno
Etaprime B/BN
2
n = 1.450 1/min
n = 2.900 1/min
EP1750.01
5 10 20 30 40 50 100 200 300 400 500US.gpm
4 5 10 20 30 40 50 100 200 300 400IM.gpm
0.3 0.4 0.5 1 2 3 4 5 10 20 30l/s
1 2 3 4 5 10 20 30 40 50 100 120Q[m /h]3
4
5
10
20
30
40
50
100
ft
1
2
3
4
5
10
20
30
35
H[m]
100--240.1 L/BN80--200 L/BN
80--190 L/BN
80--170 L/BN
65--180 L/BN
65--150 L/BN/B
50--160 L/BN/B
50--130 L/BN/B
40--140 L/BN/B
40--110 L/BN
32--120 L/BN
25--100 L/BN
1)
1)
1)
1)
1)
1)
1)
1)
1)
1) lieferbar auch in Chrom-Nickel-Molybdänstahlguss1) also available in cast CrNiMo steel1) Egalement disponible en acier moulé au CrNiMo
1) Suministrable también en Acero moldeado al Cr-Ni-Mo1) Ook leverbaar in chroom-nikkel-molybdeenstaal1) Disponibile anche come fusione di acciaio al cromo-nichel-molibdeno
EP3500.01
5 10 20 30 40 50 100 200 300 400 500US.gpm
4 5 10 20 30 40 50 100 200 300 400 500IM.gpm
0.3 0.4 0.5 1 2 3 4 5 10 20 30 40 50l/s
20 30 40 50 100 2003
20
30
40
50
100
200
300
ft
5
10
20
30
40
50
100110
H[m]
100--240.1 L/BN
80--200 L/BN
80--190 L/BN
80--170 L/BN
65--180 L/BN
65--150 L/BN/B
50--130 L/BN/B
32--120 L/BN
25--100 L/BN
50--160 L/BN/B
Q[m /h] 2 3 4 5 101
1)
40--140 L/BN/B 1)
1)
1)
1)
1)
1)
1)
1) lieferbar auch in Chrom-Nickel-Molybdänstahlguss1) also available in cast CrNiMo steel1) Egalement disponible en acier moulé au CrNiMo
1) Suministrable también en Acero moldeado al Cr-Ni-Mo1) Ook leverbaar in chroom-nikkel-molybdeenstaal1) Disponibile anche come fusione di acciaio al cromo-nichel-molibdeno
3
1)40--110 L/BN
Etaprime B/BN
3
n = 1.750 1/min
n = 3.500 1/min
Unit is insensitiveto the penetrationof gas and air.
Service-friendly, sturdyKSB IEC three phase motor
Excellent suction behaviour,self-priming up to 9 m; nofoot valve required.
Self-priming after thepump casing hasbeen filled with thefluid handled.
Inspection coverfor easy cleaning.
Back pull-out design:the casing may remainin the pipeline when thepump is dismantled.
Reliable, maintenance-free mechanical seal.
Shaft sleeve preventswear on the shaft.
UG1026788:038/1
Double-acting mechanicalseal available for toughapplications
Etaprime B/BN
4
Product Advantages at a GlanceEtaprime BN
Etaprime B/BN
5
Overview of Type SeriesSizes and types availablePump size ETAPRIME L ETAPRIME BN ETAPRIME B
Shaft GL CL GBN CBN GBunit JL 1040 1.4408 JL 1040 1.4408 JL 1040
25-100 E / T o E / T o o o32-120 17 E / T E / T E / T E / T o o40-110 E / T E / T E / T E / T o o40-140 E / T / B E / T / B E / T / B E / T / B E o50-130
25E / T / B E / T / B E / T / B E / T / B E o
50-160 25 E / T / B E / T / B E / T / B E / T / B E o65-150 E / T / B E / T / B E / T / B E / T / B E o65-180 E / T / B E / T / B E / T / B E / T / B o o80-170 E / T / B E / T / B E / T / B E / T / B o o80-190 35 E / T / B o E / T / B o o o80-200 E / T / B E / T / B E / T / B E / T / B o o
100-240.1 E / T / B o E / T / B o o o
= available sizeo = size not availableE = single-acting mechanical seal (standard design)T = double-acting mechanical seal in TANDEM arrangement possibleB = double-acting mechanical seal in BACK-to-BACK arrangement possible
MaterialsDescription Etaprime GB, GBN Etaprime CB, CBN
Volute casingCasing coverShaftImpellerDrive lantern 2)
Shaft sleeve 1)
Grey cast iron JL 1040 4)
Grey cast iron JL 1040 4)
Tempering steel C45+N 3)
Grey cast iron JL 1040 4)
Grey cast iron JL 1040 4)
Chrome nickel molybdenum steel 1.4571
Cast chrome nickel molybdenum steel 1.4408Cast chrome nickel molybdenum steel 1.4408Chrome nickel molybdenum steel 1.4571Cast chrome nickel molybdenum steel 1.4408Grey cast iron 5) JL 1040 4)
Chrome nickel molybdenum steel 1.4571
1) not fitted on shaft unit 172) not fitted on Etaprime B3) for shaft unit 17 = Chrome nickel molybdenum steel 1.45714) to EN 1561 = GJL-2505) for shaft unit 17 = Chrome nickel molybdenum steel 1.4408For shaft unit / pump size combinations see Overview of Type Series above
Flange Connections / Pump connectionsPump size Shaft Standard Special
unit connection connection25-100 Pipe thread Pipe thread32-120 17 Rp to ISO 7/1 NPT to ASME B1.20.140-11040-14050-130
2550-160 25
65-150 Flange Flange65-180 to EN 1092-2, PN16, (JL 1040) to ASME BE 16.1 Class 12580-170 to EN 1092-1, PN16, (1.4408) (to ZN 2606)80-190 3580-200
100-240.1
2746:7/3
0.5 to 1 m
Caution
Etaprime B/BN
6
Pressure limitsPumpsize
Dis-chargepressurep2 1)(bar)
Testpressure
2)
(bar)
Pump size Dis-chargepressurep2 1)(bar)
Testpressure
2)
(bar)
25-10032-12040-11040-14050-13050-160
10.010.010.010.010.010.0
15.015.015.015.015.015.0
65-15065-18080-17080-19080-200100-240.1
10.010.010.010.010.010.0
15.015.015.015.015.015.0
1) Thesumof inlet pressureand headat zero flow pointmust not exceedthe values indicated.
2) Thecasingcomponents arechecked for leakage bymeans of internalpressure tests to AN 1897/75--03 with water.
Priming Timewith a horizontal length of the suction line of 1 mand suction lineDN = pump DN
ETAPRIMEB / BN
Suction time [ sec ]for speed n = 2,900/3,500 rpm
at a static suction lift H1geo of ... mB / BN2 m 4 m 5 m 7 m 8 m
25-100 50 135 240 - -32-120 30 90 120 255 36040-110 60 135 180 300 36040-140 30 80 100 210 30050-130 50 120 150 245 30050-160 30 60 90 180 24065-150 60 150 180 300 36065-180 30 50 80 150 21080-170 50 120 180 300 36080-190 50 65 90 150 18080-200 30 60 80 195 180
100-240.1 30 50 60 90 -
Suction time [ sec ]ETAPRIME for speed n = 1,450/1,750 rpmB / BN at a static suction lift H1geo of ... m
1 m 2 m 4 m 5 m 7 m 8 m25-100 120 - - - - -32-120 150 200 - - - -40-110 140 - - - - -40-140 120 240 - - - -50-130 200 360 - - - -50-160 180 320 - - - -65-150 180 360 - - - -65-180 160 180 360 - - -80-170 150 240 420 - - -80-190 120 160 300 - - -80-200 80 120 240 300 - -100-240.1 100 140 280 400 - -
The above data refers to water at 20 �C.
When handling fluids wich liberate gas or tend tofroth, the pumpwill not be self-priming. In such
cases, a check valve should be installed in the suction line.
Electrical connection valuesPump size Motor IEC 50 60 50 Hz / 60 Hz
code size Hz Hz ~ 400 V[kW] [kW] [A]
.../ 054 80 0.6 0.6 1.4
.../ 154 90L 1.5 1.7 3.4
.../ 224 100L 2.2 2.5 4.9
.../ 304 100L 3.0 3.4 6.3
.../ 404 112M 4.0 4.6 8.3
.../ 112 80 1.1 1.3 2.6
.../ 222 90L 2.2 2.5 4.6alle .../ 302 100L 3.0 3.4 6.3
.../ 402 112M 4.0 4.6 8.3
.../ 552 132S 5.5 6.3 11.0
.../ 752 132S 7.5 8.6 14.6.../ 1102 160M 11.0 12.6 20.7.../ 1502 160M 15.0 17.3 28.0.../ 1852 160L 18.5 21.3 33.0.../ 2202 180M 22.0 24.5 40.0.../ 3002 200L 30.0 34.5 54.0
1) The above values for current in A are for orientation only. For exactcurrent values please refer to the motor nameplate.
Etaprime B/BN
7
Fluid handled Application limits Materi-als
Shaft seal Referencecode
Comments
Casing/Impeller
Mechanicalseal
Mechanicalseal
Greycastiron/
Greycastiron
CastC
rNiMosteel/
CastC
rNiMosteel
AQ1V
GG2)
U3U
3VGG
Q1Q
1X4G
G
BQ1E
GG2)
G C 8 9 10 11
Water
Ammoniawater (salmiac) t � 40 �C; conc. � 10% X X GB11,GBN11
Brackishwater t � 25�C X X CB10,CBN10
Condensate 2) t � 90�C X X GB11,GBN11
Condensate, non-conditioned t � 90�C X X CBN11
Coolingwater (no anti-freeze) 1) t � 60�C X X GB10,GBN10
open circuit: CBN10 required
Coolingwater pH value �7.5(with anti-freeze) 1) 3)
t � -30�Ct � 90�C
p �10 bar X X GB11,GBN11
open circuit: CBN11 required
Damwater 1) t � 60�C X X GB10,GBN10
if solids - laden: contact KSB
Drinkingwater 1) t � 60�C X X GB11,GBN11
Fire-fightingwater 1) t � 60�C X X GB10,GBN10
Fully desalinatedwater t � 90�C X X CBN11 Requirements for ultra-purewater can-not bemet.
Fully desalinatedwateras boiler feedwater 2)
t � 90�C X X GB11,GBN11
Partly desalinatedwater 2) t � 90�C X X GB11,GBN11
Purewater 4) t � 60�C X X GB11,GBN11
Seawater t � 25�C X X CBN10
Slightly contaminatedwater 1) t � 60�C X X GB10,GBN10
Surfacewater 1) t � 40�C X X GB8,GBN 8 Analysis of fluid handled required.
Swimming-pool water 1)(freshwater)
t � 60�C X X GB10,GBN10
Also for requirements toDIN 19 643
Untreatedwater 1) t � 60�C X X GB10,GBN10
Wastewater (industrial) Analysis of fluid handled required.
Refrigerants, cooling brines
Cooling brine, inorganic,pH value >7.5; inhibited
t � -30�Ct � 25�C
X X GB11,GBN11
Water with anti-freeze,pH value �7.5 1) 3)
t �-30�C;t � 90�C
X X GB11,GBN11
Oils/Emulsions
Drilling/Grinding emulsion t � 60�C X X GB9,GBN 9
Oil-water emulsion t � 60�C X X GB9,GBN 9
Cleaning agents
Bottle rinsing lyes t � 90�C X X GB10,GBN10
Acids
Acetic acid t � 60 �C; conc. � 5%t � 60 �C; conc. � 10%
X X CBN11
1) General criteria for results of water analysis: pH value � 7;chloride (Cl) content � 150 mg/kg. Chlorine (Cl2) � 0.6 mg/kg.Ammonia (NH3) � 5mg/kg, free from hydrogen sulphide (H2S); no limitation of Cl content required in this case.
2) Treatment to VdTÜV 1466; additional requirement : O2 � 0.02 mg/l.3) Antifreeze on ethylene glycol basis with inhibitors. Content: 20 % to 50 % (e.g. Antifrogen N)4) No ultra-pure water! Conductivity at 25 �C: � 800 �S/cm.
6 B Förderflüssigkeit-Entleerung / Casing drain / Vidange du liquide véhiculé /Scarico del liquido convogliato / Vaciado del líquido de impulsión / aftap. pomphuis
6 D Förderflüssigkeit-Auffüllen und Entlüften / Fluid handled-priming and venting /Remplissage et dégazage de liquide véhiculé / Riempimento e scaricodel liquido convogliato / Llenado y desaireacción del líquido de impulsión / vul en ontluchting
n=1.4501/min
n=1.7501/min
n=2.9001/min
n=3.5001/min
Etaprime B/BN
8
Etaprime B 40-140/... -- 65-150/...with motor foot from motor size 132 = 5.5 kW
Etaprime B 6 B 1) 6 D 1)
40-140/...50-130/...50-160/...65-150/...
Rc 3/8Rc 1/2Rc 1/2Rc 1/2
Rc 3/4Rc 3/4Rc 3/4Rc 3/4
1) Rc = ISO 7/1
Flange dimensions mmFlange Dia. of
connection DN bolt circle z d l140 110
Standard 50 125 4 40StandardEN 1092-1 65 145
4M 16
40EN 1092 1EN 1092-2 80 160
8
M 16
45100 180
8 45
S i l40 98.6 UNC 1/2-13
SpecialASME BE 16 1
50 120.74 40ASME BE 16.1
Class 12565 139.7
4UNC 5/8-11
40Class 125(ZN 2606) 80 152.4
UNC 5/8-11(ZN 2606)
100 190.5 8 45Tolerances of connecting dimensions as per EN 735 mm
Etaprime B DN a b1 b2 b3 b5 d2 d3 h1 h2 h3 h4 i l1ca. m1 m2 m3 m4 n1 n2 n3 n4 s1 s240--140 / 054 X 40 115 128 115 57 -- 170 -- 112 284 73 -- -- 460 100 70 -- -- 220 160 -- -- 16 --
/ 154 X 40 115 128 115 57 -- 190 -- 112 284 73 -- -- 491 100 70 -- -- 220 160 -- -- 16 --/ 222 X 40 115 128 115 57 -- 190 -- 112 284 73 -- -- 491 100 70 -- -- 220 160 -- -- 16 --/ 302 X 40 115 128 115 57 -- 213 -- 112 284 73 -- -- 515 100 70 -- -- 220 160 -- -- 16 --/ 402 X 40 115 128 115 57 -- 234 -- 112 284 73 -- -- 536 100 70 -- -- 220 160 -- -- 16 --
/ 552 2) X 40 115 128 115 57 43 266 12 112 284 73 132 202 601 100 70 140 220 220 160 216 270 16 1550--130 / 054 X 50 130 138 128 55 -- 170 -- 132 317 78 -- -- 475 100 70 -- -- 250 190 -- -- 20 --
/ 154 X 50 130 138 128 55 -- 190 -- 132 317 78 -- -- 506 100 70 -- -- 250 190 -- -- 20 --/ 222 X 50 130 138 128 55 -- 190 -- 132 317 78 -- -- 506 100 70 -- -- 250 190 -- -- 20 --/ 302 X 50 130 138 128 55 -- 213 -- 132 317 78 -- -- 530 100 70 -- -- 250 190 -- -- 20 --/ 402 X 50 130 138 128 55 -- 234 -- 132 317 78 -- -- 551 100 70 -- -- 250 190 -- -- 20 --
50--160 / 054 X 50 130 145 126 55 -- 170 -- 132 327 75 -- -- 475 100 70 -- -- 250 190 -- -- 20 --/ 154 X 50 130 145 126 55 -- 190 -- 132 327 75 -- -- 506 100 70 -- -- 250 190 -- -- 20 --/ 402 X 50 130 145 126 55 -- 234 -- 132 327 75 -- -- 551 100 70 -- -- 250 190 -- -- 20 --
/ 552 1) X X 50 130 145 126 55 43 266 12 132 327 75 132 202 616 100 70 140 220 250 190 216 270 20 15/ 752 1) X 50 130 145 126 55 43 266 12 132 327 75 132 202 616 100 70 140 220 250 190 216 270 20 15
65--150 / 054 X 65 140 155 149 55 -- 170 -- 160 370 85 -- -- 485 125 95 -- -- 270 212 -- -- 23/ 154 X 65 140 155 149 55 -- 190 -- 160 370 85 -- -- 516 125 95 -- -- 270 212 -- -- 23/ 402 X 65 140 155 149 55 -- 234 -- 160 370 85 -- -- 561 125 95 -- -- 270 212 -- -- 23 --
/ 552 1)2) X X 65 140 155 149 55 43 266 12 160 370 85 132 202 626 125 95 140 220 270 212 216 270 23 15/ 752 1)2) X 65 140 155 149 55 43 266 12 160 370 85 132 202 626 125 95 140 220 270 212 216 270 23 15
1) h1≥ h4 2) For these motor sizes, shims etc. will have to be fitted under the motor/pump feet.
6 B Förderflüssigkeit-Entleerung / Casing drain / Vidange du liquide véhiculé /Scarico del liquido convogliato / Vaciado del líquido de impulsión / aftap. pomphuis
6 D Förderflüssigkeit-Auffüllen und Entlüften / Fluid handled-priming and venting /Remplissage et dégazage de liquide véhiculé / Riempimento e scarico del liquidoconvogliato / Llenado y desaireacción del líquido de impulsión / vul en ontluchting
n=1.4501/min
n=1.7501/min
n=2.9001/min
n=3.5001/min
Etaprime B/BN
9
Etaprime BN
Etaprime BN 6 B 1) 6 D 1)
25-100/...32-120/...40-110/...
Rc 1/8Rc 1/8Rc 1/8
Rc 3/4Rc 3/4Rc 3/4
1) Rc = ISO 7/1
Tolerances of connecting dimensions as per EN 735 mm
Connection
Standard SpecialEtaprime BN 4) DN 2) DN 3) a b1 b2 h1 h2 h3 i l1 ca. w
25--100 / 054 X X Rp 1 NPT 1 70 104 95 87 227 38 152 399 102/ 112 X X Rp 1 NPT 1 70 104 95 87 227 38 152 399 102
32--120 / 054 X X Rp 1 1/4 NPT 1 1/4 95 118 95 90 239 46 149 421 99/ 112 X X Rp 1 1/4 NPT 1 1/4 95 118 95 90 239 46 149 421 99
40--110 / 054 X X Rp 1 1/2 NPT 1 1/2 105 118 110 101 256 55 154 436 104/ 112 X X Rp 1 1/2 NPT 1 1/2 105 118 110 101 256 55 154 436 104
2) Standard connection to ISO 7/13) Special connection to ASME B1.20.14) For these motor sizes, 30 mm thick shims etc. must be placed under the motor feet.
6 B Förderflüssigkeit-Entleerung / Casing drain / Vidange du liquide véhiculé /Scarico del liquido convogliato / Vaciado del líquido de impulsión / aftap. pomphuis
6 D Förderflüssigkeit-Auffüllen und Entlüften / Fluid handled-priming and venting /Remplissage et dégazage de liquide véhiculé / Riempimento e scarico del liquidoconvogliato / Llenado y desaireacción del líquido de impulsión / vul en ontluchting
Etaprime B/BN
10
Etaprime BNwith motor foot from motor size 132 = 5.5 kW
Etaprime BN 6 B1) 6 D1)
40-140/...50-130/...50-160/...65-150/...
Rc 3/8Rc 1/2Rc 1/2Rc 1/2
Rc 3/4Rc 3/4Rc 3/4Rc 3/4
65-180/...80-170/...80-190/...80-200/...
100-240.1/...
Rc 1/2Rc 3/4Rc 3/8Rc 1/2Rc 3/4
Rc 3/4Rc 3/4Rc 3/4Rc 3/4Rc 3/4
1) Rc = ISO 7/1
Flange dimensions mmFlange Dia. of
connection DN bolt circle z d l140 110
Standard 50 125 4 40StandardEN 1092-1 65 145
4M 16
40EN 1092 1EN 1092-2 80 160
8
M 16
45100 180
8 45
S i l40 98.6 UNC 1/2-13
SpecialASME BE 16 1
50 120.74 40ASME BE 16.1
Class 12565 139.7
4UNC 5/8-11
40Class 125(ZN 2606) 80 152.4
UNC 5/8-11(ZN 2606)
100 190.5 8 45
n=1.4501/min
n=1.7501/min
n=2.9001/min
n=3.5001/min
Etaprime B/BN
11
Tolerances of connecting dimensions as per EN 735 mm
Etaprime BN DN a b1 b2 b3 b4 b5 d1 d2 d3 h1 h2 h3 h4 i l1ca. m1 m2 m3 m4 n1 n2 n3 n4 s1 s2 w x40--140/ 054 X 40 115 128 115 57 16 -- 200 170 -- 112 284 73 -- -- 510 100 70 -- -- 220 160 -- -- 16 -- 123 100/ 154 X 40 115 128 115 57 16 -- 200 190 -- 112 284 73 -- -- 570 100 70 -- -- 220 160 -- -- 16 -- 166 100/ 222 X 40 115 128 115 57 16 -- 200 190 -- 112 284 73 -- -- 570 100 70 -- -- 220 160 -- -- 16 -- 166 100/ 302 X 40 115 128 115 57 16 -- 250 213 -- 112 284 73 -- -- 608 100 70 -- -- 220 160 -- -- 16 -- 180 100/ 402 X 40 115 128 115 57 16 -- 250 234 -- 112 284 73 -- -- 629 100 70 -- -- 220 160 -- -- 16 -- 180 100
/ 552 2) X 40 115 128 115 57 16 43 300 266 12 112 284 73 132 292 717 100 70 140 220 220 160 216 270 16 15 203 10050--130/ 054 X 50 130 138 128 55 16 -- 200 170 -- 132 317 78 -- -- 510 100 70 -- -- 250 190 -- -- 20 -- 123 100/ 154 X 50 130 138 128 55 16 -- 200 190 -- 132 317 78 -- -- 570 100 70 -- -- 250 190 -- -- 20 -- 166 100/ 222 X 50 130 138 128 55 16 -- 200 190 -- 132 317 78 -- -- 585 100 70 -- -- 250 190 -- -- 20 -- 166 100/ 302 X 50 130 138 128 55 16 -- 250 213 -- 132 317 78 -- -- 623 100 70 -- -- 250 190 -- -- 20 -- 180 100/ 402 X 50 130 138 128 55 16 -- 250 234 -- 132 317 78 -- -- 644 100 70 -- -- 250 190 -- -- 20 -- 180 100
50--160/ 054 X 50 130 145 126 55 16 -- 200 170 -- 132 327 75 -- -- 510 100 70 -- -- 250 190 -- -- 20 -- 123 100/ 154 X 50 130 145 126 55 16 -- 200 190 -- 132 327 75 -- -- 570 100 70 -- -- 250 190 -- -- 20 -- 166 100/ 402 X 50 130 145 126 55 16 -- 250 234 -- 132 327 75 -- -- 644 100 70 -- -- 250 190 -- -- 20 -- 180 100
/ 552 1) X X 50 130 145 126 55 16 43 300 266 12 132 327 75 132 292 732 100 70 140 220 250 190 216 270 20 15 203 100/ 752 1) X 50 130 145 126 55 16 43 300 266 12 132 327 75 132 292 732 100 70 140 220 250 190 216 270 20 15 203 10065--150/ 054 X 65 140 155 149 55 16 -- 200 170 -- 160 370 85 -- -- 510 125 95 -- -- 270 212 -- -- 23 123 100/ 154 X 65 140 155 149 55 16 -- 200 190 -- 160 370 85 -- -- 570 125 95 -- -- 270 212 -- -- 23 166 100/ 402 X 65 140 155 149 55 16 -- 250 234 -- 160 370 85 -- -- 644 125 95 -- -- 270 212 -- -- 23 -- 180 100
/ 552 1)2) X X 65 140 155 149 55 16 43 300 266 12 160 370 85 132 292 732 125 95 140 220 270 212 216 270 23 15 203 100/ 752 1)2) X 65 140 155 149 55 16 43 300 266 12 160 370 85 132 292 732 125 95 140 220 270 212 216 270 23 15 203 10065--180/ 224 X X 65 140 158 138 55 16 -- 250 213 -- 160 376 89 -- -- 650 125 95 -- -- 270 212 -- -- 23 -- 180 140
/ 552 1)2) X 65 140 158 138 55 16 43 300 266 12 160 376 89 132 322 772 125 95 140 220 270 212 216 270 23 15 233 140/ 752 1)2) X 65 140 158 138 55 16 43 300 266 12 160 376 89 132 322 772 125 95 140 220 270 212 216 270 23 15 233 140/ 1102 1) X 65 140 158 138 55 16 70 350 325 14 160 376 89 160 374 952 125 95 210 300 270 212 254 320 23 21 266 14080--170/ 224 X X 80 156 173 168 65 18 -- 250 213 -- 160 380 104 -- -- 650 140 106 -- -- 310 240 -- -- 21 -- 180 140
/ 752 1)2) X 80 156 173 168 65 18 43 300 266 12 160 380 104 132 322 788 140 106 140 220 310 240 216 270 21 15 233 140/ 1102 1) X 80 156 173 168 65 18 70 350 325 14 160 380 104 160 374 968 140 106 210 300 310 240 254 320 21 21 266 140/ 1502 1) X 80 156 173 168 65 18 70 350 325 14 160 380 104 160 374 968 140 106 210 300 310 240 254 320 21 21 266 14080--190/ 224 X X 80 170 188 181 65 20 -- 250 213 -- 180 420 107 -- -- 650 160 120 -- -- 345 280 -- -- 25 -- 180 140
/ 1102 1)2) X 80 170 188 181 65 20 70 350 325 14 180 420 107 160 374 982 160 120 210 300 345 280 254 320 25 21 266 140/ 1502 1)2) X 80 170 188 181 65 20 70 350 325 14 180 420 107 160 374 982 160 120 210 300 345 280 254 320 25 21 266 140/ 1852 1)2) X 80 170 188 181 65 20 70 350 325 14 180 420 107 160 374 982 160 120 254 314 345 280 254 320 25 21 266 14080--200/ 224 X X 80 154 172 152 65 20 -- 250 213 -- 160 378 107 -- -- 650 140 100 -- -- 285 220 -- -- 25 -- 180 140
/ 1102 1) X 80 154 172 152 65 20 70 350 325 14 160 378 107 160 374 966 140 100 210 300 285 220 254 320 25 21 266 140/ 1502 1) X 80 154 172 152 65 20 70 350 325 14 160 378 107 160 374 966 140 100 210 300 285 220 254 320 25 21 266 140/ 1852 1) X 80 154 172 152 65 20 70 350 325 14 160 378 107 160 374 966 140 100 254 314 285 220 254 320 25 21 266 140
100--240.1/ 224 X 100 182 203 178 65 20 -- 250 213 -- 200 457 127 -- -- 650 140 100 -- -- 330 260 -- -- 21 -- 180 140/ 304 X X 100 182 203 178 65 20 -- 250 213 -- 200 457 127 -- -- 650 140 100 -- -- 330 260 -- -- 21 -- 180 140/ 404 X 100 182 203 178 65 20 -- 250 234 -- 200 457 127 -- -- 670 140 100 -- -- 330 260 -- -- 21 -- 180 140
/ 1502 1)2) X 100 182 203 178 65 20 70 350 325 14 200 457 127 160 362 982 140 100 210 300 330 260 254 320 21 21 254 140/ 1852 1)2) X 100 182 203 178 65 20 70 350 325 14 200 457 127 160 362 982 140 100 254 314 330 260 254 320 21 21 254 140/ 2202 1)2) X 100 182 203 178 65 20 80 350 370 14 200 457 127 180 375 1046 140 100 241 320 330 260 279 360 21 23 254 140/ 3002 1) X 100 182 203 178 65 20 80 400 422 18 200 457 127 200 387 1105 140 100 305 385 330 260 318 400 21 34 254 140
1) h1≥ h42) For these motor sizes, shims etc. will have to be fitted under the motor/pump feet.
2746.5/6-10
1.2.2005
Subjecttotechnicalm
odificationwithoutpriornotice.
Volutecasing
Casingcover
Shaft1)
Impeller
Mechanicalseal
Shaftsleeve
102
161
210
230
523
Shaftunit
433.01
11
X
Same number meanssame component
Components differ
Component not fitted
Component interchangeable with Etaprime L
O
KSB Aktiengesellschaft67225 Frankenthal � Johann-Klein-Str. 9 � 67227 Frankenthal (Germany)Tel. +49 6233 86-0 � Fax +49 6233 86-3401 � www.ksb.com
Etaprime B/BN
Interchangeability of Etaprime B/BN and Etaprime L Components and Interchangeability of Component Parts
Description
Part No.
Etaprime B/BN
25-100 O X 1 O 1 X
32-120 17 O X 1 O 1 X
40-11017
O X 1 O 1 X
40-140 O O 2 O 2 1
50-13025
O O 2 O 2 1
50-16025
O O 2 O 2 1
65-150 O O 2 O 2 1
65-180 O O 3 O 3 2
80-170 O O 3 O 3 2
80-190 35 O O 3 O 3 2
80-20035
O O 3 O 3 2
100-240.1 O O 3 O 3 2
1) only for Etaprime GBN, CBN
Recommended Spare Parts Stock for 2 Years’ Continuous Operation to DIN 24 296
Part No. Description Number of Pumps (incl. stand-by pumps)
2 3 4 5 6 and 7 8 and 9 10 and more
Quantity of spare parts
210 Shaft 1) 1 1 1 2 2 2 20 %
230 Impeller 1 1 1 2 2 2 20 %
400.03 Gasket 2) 1 1 2 2 2 3 25 %
412.35/.65 1) O-ring (set) 4 6 8 8 9 10 100 %
433.01 Mechanical seal 1 1 2 2 2 3 25 %
523 Shaft sleeve 2) 2 2 2 3 3 4 50 %
1) only for Etaprime GBN, CBN2) not fitted on shaft unit 17Applicable shaft unit/pump size combinations see above.