EVID Owner's Manual 909 KB

Owner’s Manual

TOC

Table of Contents .............................. TOC

Safety First ..................................... TOC

Product Description ............................... 1

Welcome ............................................... 1

Important Features ............................... 1

Model Summary ................................... 2

Packing List .......................................... 2

EVIDTM Product Family ......................... 3

Product Feature Identification .............. 3

SAMTM (Strong-Arm-MountTM) System . 4

Step-by-Step Installation and Wiring .... 4

Step 1 - Mount the SAMTM Bracket .. 4

Step 2 - Select Wattage Tap (Models 4.2t and 6.2t Only) ............................ 5

Step 3 - Mount the Speaker to the SAMTM Bracket ................................. 5

Step 4 - Wire the Speaker ................ 6

Step 5 - Secure the Seismic Tab Connection Point .............................. 6

Step 6 - Test System Operation ....... 6

Packing List (12.1 Subwoofer) ............. 7

Product Feature Identification (12.1 Subwoofer) ........................................... 7

Step-by-Step Installation and Wiring (12.1 Subwoofer) .................................. 8

Step 1 - Mount the Bracket .............. 8

Step 2 - Install the Safety Line ......... 8

Step 3 - Wire the Speaker ................ 8

EVIDTM Owner’s Manual

Table of Contents

Step 4 - Mount the Speaker to the Bracket ............................................. 9

Step 5 - Test System Operation ..... 10

Safety Agency Compliance ................ 10

Maintenance ....................................... 10

Uniform Limited Warranty ................... 11

Exclusions and Limitations ................. 11

Obtaining Warranty Service ............... 11

Incidental and Consequential Damages Excluded ............................................. 11

Other Rights ....................................... 11

Speakers and Electronics .................. 11

Appendix A - Integrating the 12.1Subwoofer ............................................. 12

Installation Examples ......................... 12

Using the 12.1 in Passive Mode ........ 12

Crossover Freq. and Impedance ....... 12

Using a Separate Amplifier Channel for the 12.1 ............................................... 12

Characteristics of All Subwoofers ...... 12

Appendix B - Painting the Speaker .... 13

Painting Process (3.2, 4.2, 6.2) ......... 13

Painting the Grille ............................... 13

Painting Process (12.1 Subwoofer) ... 13

Appendix C - Troubleshooting Table . 14

Appendix D - Technical Specs ............ 15

3.2/3.2t; 4.2/4.2t ................................. 15

6.2/6.2t; 12.1 ...................................... 16

Notes ...................................................... 17Safety First

Suspending any object is potentially dangerous and should only be attempted by individuals whohave a thorough knowledge of the techniques and regulations of rigging objects overhead. Electro-Voice® strongly recommends that all speakers be suspended taking into account all current national,federal, state and local regulations. It is the responsibility of the installer to ensure that all speakersare safely installed in accordance with all such regulations. When speakers are suspended, Electro-Voice® strongly recommends that the system be inspected at least once a year. If any sign ofweakness or damage is detected, remedial action should be taken immediately. The user isresponsible for making sure that the supporting surfaces, and any additional hardware used, iscapable of supporting the loudspeaker. Any hardware used to suspend a loudspeaker array that isnot provided by/associated with Electro-Voice® is the responsibility of others.

EVIDTM Owner’s Manual 1

Product Description

WelcomeThank you for purchasing EVID™ Seriesloudspeakers. Read through this manualto familiarize yourself with the features,applications, and precautions before youuse these products.

EVID™ Series loudspeakers useinnovative design and materials to providepremium-level performance from compactsurface-mount speakers.

Four models comprise the EVID™ Series:the 6.2 with dual 6-inch LF drivers and a 1-inch titanium tweeter with waveguide; the4.2 with dual 4-inch LF drivers and a 1-inch titanium tweeter with waveguide; the3.2 with dual 3.5-inch LF drivers and a .75-inch titanium direct radiator tweeter. TheEVID™ 12.1, a subwoofer designed toaugment and extend the full-range model’slow-frequency response completes theline.

Important Features• Line-array enhanced coverage control• Organic, unobtrusive shape• SAM™ (Strong-Arm-Mount™) system

for secure and reliable mounting• Extremely large speaker swing and

rotation ranges for flexible placementand coverage everywhere

• Full bandwidth overload protection• Weather resistant and paintable• Dual LF transducers• Extended bass• Greater power handling and output• Titanium HF transducers (4.2, 6.2

waveguide coupled)• High sensitivity• Shielded for video applications

EVIDTM Owner’s Manual2

Product Description

erugiF ytitnauQ traP

A 2 metsySrekaepS

B 2 MAS MT ylbmessA

C 2 paCogoLegraL

C 2 paCogoLllamS

D 1 launaMs'renwO

E 1 draCytnarraW

F 1 MAS MT looTgnitnuoM

Figure 1: EVIDTM Components

Model SummaryEVID™ 3.2Most compact of the EVID™ Series, theEVID™ 3.2 uses dual 3.5-inch LF driverswith a .75-inch titanium direct radiatortweeter to provide high-fidelity, full-rangesound over an extremely wide coveragearea. The EVID™ 3.2t includes atransformer for 70V or 100V systems.

EVID™ 4.2The compact EVID™ 4.2 delivers very full-range sound from its dual 4-inch LFdrivers and a 1-inch titanium tweeter withwaveguide. It is able to deliver a 110-dBsound level over a wide coverage area.The EVID™ 4.2t includes a multi-taptransformer for 70V or 100V line distribu-tion systems.

EVID™ 6.2The EVID™ 6.2 is an extended-rangehigh-output speaker with dual 6.5-inchwoofers and a 1-inch titanium tweeter withwaveguide, designed for high SPL over awide coverage area. The EVID™ 6.2tincludes a multi-tap transformer for a 70Vor 100V line distribution system.

EVID™ 12.1This subwoofer’s unique 12-inch dual-voice-coil woofer design and side/frontangled port system allows for powerfullow-frequency reinforcement from aflexible, compact wall- or ceiling-mountedenclosure. The EVID™ 12.1's full, richbass is an ideal addition to any EVID™system.

Packing List (3.2, 4.2, 6.2)Listed and illustrated below are the partsincluded in each boxed pair of EVID™speakers.

A

B

C

ED F


Product Description

EVID™ Product Family Product Feature IdentificationIllustrated below are the major compo-nents of the EVID™ Series full-rangespeakers.

Figure 2: EVIDTM Features (Front)

Figure 3: EVIDTM Features (Back)

A. Shielded dual woofersB. Coherent Coverage Waveguide horn

(4.2 and 6.2 only)C. Dual low-frequency portsD. Treated woofer conesE. Durable zinc-plated steel grille (not shown)F. Cast aluminum Strong-Arm-Mount™ (SAM™)G. Over 100 degrees of swing; 90 degrees

of rotationH. Simple keyed socket head adjustmentsI. Titanium dome tweeters with neodymium

magnet structures

A

I H

G

F

(E)

D

CB

ecnadepmImho-8

.oNtraP ledoM noitpircseD

100-540103 2.3egnaR-lluF"5.3lauD

)kcalB(dedleihS

200-540103 w2.3egnaR-lluF"5.3lauD

)etihW(dedleihS

100-640103 2.4egnaR-lluF"4lauD

)kcalB(dedleihS

200-640103 w2.4egnaR-lluF"4lauD

)etihW(dedleihS

100-740103 2.6egnaR-lluF"6lauD

)kcalB(dedleihS

200-740103 w2.6egnaR-lluF"6lauD

)etihW(dedleihS

stinUdeppiuqEtloV-001/tloV-07


300-540103 t2.3egnaR-lluF"5.3lauD

)kcalB(dedleihS

400-540103 wt2.3egnaR-lluF"5.3lauD

)etihW(dedleihS

300-640103 t2.4egnaR-lluF"4lauD

)kcalB(dedleihS

400-640103 wt2.4egnaR-lluF"4lauD

)etihW(dedleihS

300-740103 t2.6egnaR-lluF"6lauD

)kcalB(dedleihS

400-740103 wt2.6egnaR-lluF"6lauD

)etihW(dedleihS

srefoowbuS


100-840103 1.21tupnIlauD"21

)kcalB(

200-840103 w1.21tupnIlauD"21

)etihW(


Figure 4: Rotation Range (90°)

Product Description

SAM™ (Strong-Arm-Mount™) SystemEVID™’s SAM™ system (Strong-Arm-Mount™) excels at meeting the fourrequirements for mounting FGM/BGMsystems: simple, quick, versatile, andreliable. Three easy steps and you aredone: Attach the surface bracket to thewall or ceiling; attach the EVID™enclosure to the bracket with the socket-head bolt; aim the enclosure and tightenthe bolt. SAM™ allows greater flexibilityfor aiming than ball-type mounts that limitrange of motion when not on center.Typical ball designs have limited rotationwhen pointing straight ahead, and eventhat is reduced when the enclosurecontacts the wall and is moved off axis. Bycontrast, SAM™ allows full rotation evenat full sweep. Figure 4 shows SAM™’srange of rotation (note that EVID™’scurved cabinet allows it to rotate muchfurther [90°] than a rectangular ortrapezoidal box). Figure 5 shows the rangeof sweep motion left and right on the wall.All three models allow 100° of sidewisemotion.

Step-by-Step Installationand Wiring (3.2, 4.2, 6.2)Step 1: Mount the SAM™ Bracketto the WallThe SAM™ bracket can be mounted oneither side of the speaker, enablingoptimal configuration for any installation.Determine whether the bracket should bemounted on the left or right side of thespeaker before you bolt the speaker tothe bracket. It is best to mount the bracketon the side away from the direction inwhich the speaker will be aimed. Thisensures that the full swing angle isavailable for aiming on that side andprovides easier access to the swingtightening bolt on the wall bracket (seeFig. 10, Step 3). For safety, make sure themounting surface can support more thanthe speaker's weight! Use only industry-accepted fasteners and mountingmethods when mounting the bracket.Consult an expert if you are not sure.Read steps 2 and 3 before wiring thespeaker in step 4.For standard vertical installation mount theSAM™ bracket as shown in Figure 6. Forhorizontal mounting configurations,mounting the bracket on the bottom side(as in Figure 7) is easiest and safest, andallows the speaker to be mounted closerto the ceiling.

Figure 6: SAMTM Mounted on Side

Figure 5: Sweep Range (100°) Figure 7: SAMTM Mounted on Bottom

90˚

100˚

SAM™

SAM™Ceiling


Figure 8: Wattage Taps (4.2t & 6.2t)

Product Description

Step 2: Select Wattage Tap(Models 4.2t and 6.2t Only)Before mounting the speaker to thebracket, select the proper wattage tapsetting for your installation. The wattageselector switch is located at the rear of thespeaker below the input terminal panel.The EVID™ 4.2t and 6.2t include a switchfor selecting the power taps. The EVID™3.2t has a single power tap.EVID™ 3.2tA single (non-selectable) power tap ratedat 5W@70V and [email protected]™ 4.2tThe power taps are 30W, 15W and 7.5Wat both 70.7V and 100V, with a 3.7W tapfor 70.7V only, as well as an 8 ohmtransformer bypass setting.EVID™ 6.2t:The power taps are 60W, 30W and 15Wat both 70.7V and 100V, with a 7.5W tapfor 70.7V only, as well as an 8 ohmtransformer bypass setting.The taps for the models listed above areselected by a rotary switch on the backpanel. A guide on the back of eachspeaker shows which switch positions touse for the power settings at 70V and100V.Figure 8 below illustrates the settings forthe 4.2t and 6.2t.

Step 3: Mount the Speaker to theSAM™ BracketAttach the speaker to the SAM™ bracketwith the socket head bolt B, as shown inFigure 9.

Figure 10: Recommended TorqueSettings for Bolt A

Using the provided security tool, tightenthe two socket head bolts shown in Fig.9. Select the proper horizontal angle andsecure it by tightening Bolt A to the propertorque listed in Fig. 10. Then select theproper vertical angle and secure it bytightening Bolt B. Use the 15° anglemarkers as your guide (see Fig. 9). Attachboth logo caps as shown in Figure 11after tightening and securing the speaker.

4.2t6.2t

Figure 11: Attach Logo Caps

EV logo cap(large)

EV logo cap(small)

Figure 9: Tighten Socket Head Bolts

Bolt A(swing)

Bolt B(rotation)

15˚ angle markers

Model TorqueEVID 3.2 20-30 in-lbs (2.3-3.4 N-m)EVID 4.2 30-50 in-lbs (3.4-5.2 N-m)EVID 6.2 70-90 in-lbs (7.9-10.2 N-m)


Product Description

Step 4: Attach the Wiring to theTerminal Connector and Wire theSpeakerThe 4-pin phoenix-style plug-in connectorprovides for a pass-thru audio connectionto daisy-chain a line of speakers. Insertthe bare end of wire into the appropriateconnector terminals as described below.For parallel wiring, see Figure 12. Whenone input connector is removed, subse-quent speakers will remain connected.For daisy-chaining, see Figure 13. Whenone input connector is removed, subse-quent speakers will be disconnected.Screw down the hold-down screw untiltight, using a small screwdriver. SeeFigure 14. The connector accepts up to12 gauge wire.

Step 5: Secure the Seismic TabConnection PointThe rear of the enclosure includes aneyebolt for connection to a seismicrestraint. Connect it to a properly ratedhardware fitting that is securely installedindependently of the SAM™ bracket. Evenif your local construction code does notrequire the installation of secondarysupport, its use is highly recommended forfurther security.

Step 6: Test System OperationAfter all connections are made, test thecomplete system operation. Appendix C(page 14) contains a troubleshooting tableto assist in locating many speaker-relatedproblems.

Figure 14: Tighten With Screwdriver

Figure 12: Parallel Wiring

Figure 13: Daisy-Chain Wiring

Figure 15: Secure Seismic SecurityCable

Figure 16: EVIDTM System

Screwdriver

From amplifier orprevious speaker

To next speaker

From amplifier orprevious speaker

To next speaker


Product Description

Packing List (12.1 Subwoofer)Below is the list of parts included with theEVID™ 12.1 subwoofer. The parts areillustrated in Figure 17.

Product Feature IdentificationThe 12.1 subwoofer comes with a dual-mode mounting bracket that enables theunit to be easily mounted at either a wall/wall (corner) or on a wall/ceiling (midwall)junction. The included forged steel eyeboltprovides the installer a solid attachmentpoint for a safety line. The 12.1 subwoofermay also be safely installed protruding just2 3/4" down through a standard sus-pended ceiling grid. See installationinstructions.Illustrated below are the major compo-nents of the EVID™ Series 12.1subwoofer.

Figure 17: EVIDTM 12.1 Components Figure 19: EVIDTM 12.1 Features(Back)

Figure 18: EVIDTM 12.1 Features(Front)

AB

C

E F

D

G

Acousticports

EV®

logo

Dual-modemountingbracket

Bracket clipmounting

points

Safety lineattachment

eyebolt

Input/outputconnector

panel

erugiF ytitnauQ traP

A 1DIVE MT 1.21

refoowbuS

B 1gnitnuoMrenroC/llaW

tekcarB

C 2gnitnuoMrekaepS

spilC

D 4gnitnuoMrebbuR

teeF

E 1 tlobeyE

F 1 launaMs'renwO

G 1 draCytnarraW


Product Description

Step-by-Step Installationand Wiring (12.1Subwoofer)Step 1: Mount the BracketThe mounting bracket can be installed twoways (see Figures 20 and 21), allowingoptimal configurations for installations.Leave 1.5" of space between thebracket and the ceiling when installingin a corner!Attach the bracket to the wall with suitablefasteners screwed into structural membersin the wall. Remember: It is theinstaller's responsibility to insure thatthe structure can safely support theload.

Step 2: Install the Safety LineUsing accepted safe rigging practices,secure one end of a suitable safety line(use cable, not chain, which will rattle) to astrong, secure point above the speaker, apoint that can withstand the shock of thefalling speaker. This is especiallyimportant in public spaces constructedwith light-gauge steel studs. Do notattach the safety line to the bracket! Thesafety line should prevent the speakerfrom falling if the bracket tears loose fromthe wall. Secure the other end to theeyebolt that is fully threaded into theenclosure.

Step 3: Wire the SpeakerThe amplifier and satellite speakers arewired as shown in Figure 22. It is highlyadvisable to support the unit while theseconnections are being made. Connect allwires to the speaker at the back terminalplate observing proper polarity of theconnections. The push-terminals acceptstranded wire up to 14 gauge. When usingtwo satellites, wire the speakers directlyinto the output terminals of the panel. Foursatellites may be connected either as twopairs directly to the output terminals orwith daisy-chain wiring as in Figure 23.

Figure 20: Corner Installation (TopView)

Figure 21: Midwall Installation (SideView)

Figure 22: Direct Wiring Plan

Stud

Wall

Use amimimum offour screws

Bracket

Wall

Stud

Stud

Wall

Use amimimum offour screws

Ceiling Bracket

Joist

Topplate

- L +

- L +

- R +

- R +

fromamplifier

to speakers

Left 1 Right 1

Right 2Left 2


Product Description

Step 4: Mount the Speaker to theBracketFirst remove the two Phillips-head screwson the rear of the enclosure. Use thesupplied eyebolt to mount one mountingclip to the top of the speaker as shown inFigure 24. Check to make sure that thewiring connections to the amplifier and thesatellite speakers are correct and secure.

For corner mountingAttach the four rubber mounting feet to thefront side edges, and secure the safetyline to the eyebolt. Lift the enclosure up tothe ceiling and center it back it into thecorner until it touches the bracket rungs,then carefully lower it so the top clip hooksover the top rung of the bracket (1). Insertone of the 3/8-16-thread Phillips-headscrews through the remaining clip and,with the clip pointing up, thread the screwfinger-tight into the lower mtg. hole on theenclosure (2, 3). Level the clip and tightensecurely with a #3 right-angle Phillipsscrewdriver.

For midwall mountingAttach the four rubber mounting feet insidethe corners on the side of the enclosurethat will be against the wall and attach thesafety line to the eyebolt. Insert one of the3/8-16-thread Phillips-head screwsthrough the remaining clip and keep itwithin arm's reach. Lift the enclosure up tothe ceiling and bring its back into contactwith the bracket rungs. Slide the enclosuresideways to engage the clip over onebracket rung (1) and, while holding it tightagainst both rungs, insert the 3/8-16-thread screw with its clip into the remain-ing mounting hole so the clip engages theremaining bracket rung (2, 3). Finger-tighten the screw and straighten the clip.The enclosure may now be released. It willslide down the rungs until the four rubberfeet are snug against the wall. Using a #3right-angle Phillips screwdriver, securelytighten the second Phillips-head screw.Gently rotate the EV® logo a quarter turnand press firmly at its center to seat itsecurely into its mounting hole. See Figure25 on p. 10.

Even though the enclosure hangs from thetop clip, always install the lower one tosecure against possible disengagement ofthe top clip. Straighten the EV® logo andpress firmly at its center to seat it securelyinto its mounting hole.

Figure 23: Daisy-Chain Wiring PlanFigure 24: Corner Mounting

– L +

– L +

– R +

– R +

fromamplifier

Left 1

–

+

–

+

–

+

Right 1

Right 2Left 2

1

Rungs

3

2


Product Description

Mounting through a suspendedceiling gridOn the rear of the enclosure install andtighten two 3/8-16-thread forged steeleyebolts (one is included) with a 3/8" flatwasher under each. Cut two pieces ofordinary drop ceiling L angle (wall track)23 3/4" long and screw them to the topand bottom of the enclosure with 3/4"-lomg sheet metal screws, as shown inFigure 26. Connect all the wires andsuspend the enclosure, face down, by theeyebolts in accordance with accepted saferigging practice. Adjust the length of therigging cables so the tips of the installed Langles just rest on the ceiling cross-tees.This stabilizes the enclosure from rocking.Trim the ceiling panel to fit the newopening(s) and drop into place. It is theinstaller's responsibility to assure that thechosen rigging points are strong enough tosupport the load. Warning: Never try toinstall this speaker in a suspendedceiling without proper rigging support!

Floor MountingThe EVID™ 12.1 may be placed directlyon the floor in a corner or on its side alonga straight wall by simply attaching the fourrubber mounting feet to the side that willsit on the floor.

Step 5: Test System OperationAfter all connections are made test thecomplete system operation. Appendix Con p. 14 contains a troubleshooting guideto assist in locating a variety of speakerrelated problems.

Safety Agency ComplianceThe EVID™ 12.1 bracket system hassuccessfully passed EIA 636 at a safetyfactor of 8:1. The bracket system isintended to support the EVID™ 12.1 only.Do not use it for any other purpose. Neverset anything on, or hang anything from,the EVID™ 12.1 enclosure when usingthis bracket.For a copy of the model-specific CEDeclaration of Conformity, contact Electro-Voice at the address listed at the end ofthis manual.

MaintenanceYour EVID™ system has been designedand manufactured to provide years ofdurability and reliable service. No routinemaintenance is necessary. Units may becleaned by wiping with a soft, damp cloth.Never use solvents or harsh cleaningagents of any kind.

Figure 25: Midwall Mounting Figure 26: Attach L-Angles toSpeaker

1

3

2Rungs

This side towards wall

L angle Ceilingtile

Riggingcables

Acoustic port

Eyebolts


Uniform Limited Warranty

Electro-Voice® products are guaranteedagainst malfunction due to defects inmaterials or workmanship for a specifiedperiod, as noted in the individual product-line statement(s) below, or in the individualproduct data sheet or owner's manual,beginning with the date of originalpurchase. If such malfunction occursduring the specified period, the product willbe repaired or replaced (at our discretion)without charge. The product will bereturned to the customer prepaid.

Exclusions and LimitationsThe Limited Warranty does not apply to:(a) exterior finish or appearance; (b)certain specific items described in theindividual product-line statements below,or in the individual product sheet orowner's manual; (c) malfunction resultingfrom use or operation of the product otherthan as specified in the product data sheetor owner's manual; (d) malfunctionresulting from misuse or abuse of theproduct; or (e) malfunction occurring atany time after repairs have been made tothe product by anyone other than Electro-Voice® Service or any of its authorizedrepresentatives.

Obtaining Warranty ServiceTo obtain warranty service, a customermust deliver the product, prepaid, toElectro-Voice® Service or to any of itsauthorized service representatives,together with proof of purchase of theproduct in the form of a bill of sale orreceipted invoice. A list of authorizedservice representatives is available fromElectro-Voice® Service at 12000 PortlandAvenue, Burnsville, MN 55337. Ph: (877)863-4166.

Incidental and ConsequentialDamages ExcludedProduct repair or replacement and returnto the customer are the only remediesprovided to the customer. Electro-Voice®shall not be liable for any incidental orconsequential damages including, withoutlimitation, injury to persons or property orloss of use. Some states do not allow theexclusion or limitation of incidental orconsequential damages, so the abovelimitation or exclusion may not apply toyou.

Other RightsThis warranty gives you specific legalrights, and you may also have other rightswhich vary from state to state.

Speakers and ElectronicsElectro-Voice® Speakers and SpeakerSystems are guaranteed against malfunc-tion due to defects in materials orworkmanship for a period of five (5) yearsfrom the date of original purchase. TheLimited Warranty does not apply to burnedvoice coils or malfunctions such as coneand/or coil damage resulting fromimproperly designed enclosures. Electro-Voice® active electronics associated withthe speaker systems are guaranteed forthree (3) years from the date of originalpurchase. Additional details are included inthe Uniform Limited Warranty statement.


Appendix A: Integrating the Subwoofer

Installation ExamplesThe EVID™ Series is a product family withthe flexibility to fit the requirements ofmany different applications. Listed beloware some suggested combinations forsystems using the 12.1.• Rich, full-sounding low-level background

music and paging in a quiet restaurant,office, or retail space: two EVID™ 3.2sin parallel on each output of a 12.1.

• Moderate-level music and paging in asports bar/restaurant or upbeat retailspace: two EVID™ 4.2s in parallel oneach output of a 12.1.

• Higher-level foreground music in bass-heavy applications such as dance floors,amusement arcades, or loud bars: useone EVID™ 6.2 on each output of 12.1.

EVID™ systems may be used together.For example, a large hotel might use eight3.2s and two 12.1s in the dining room,eight 4.2s and two 12.1s in the lounge,four 6.2s with two 12.1s surrounding thedance floor, 6.2s around the pool, 6.2s or4.2s with or without 12.1s in the lobby, and3.2s in the corridors.

Crossover Frequency andImpedanceThe EVID™ 12.1 is designed to be usedas a passive subwoofer. No additionalamplifiers or signal processors arerequired to achieve full benefit of the12.1's performance. The built-in passivestereo crossover sends the lowest notesof both stereo channels to the 12" dual-coilbass driver and reduces the amount of lowfrequencies sent to the satellite speakers.This allows them to play louder andcleaner while presenting a more even,amplifier-friendly impedance load than if allthe speakers were connected in parallel.The EVID™ 12.1's crossover tunes acombination of electrical and acousticcharacteristics to complement theresponse of the full-range EVID™ models.The crossover point is set electrically inthe 160Hz range with a topology thatenables the nominal system impedance tobe determined by the number of satellitesper channel.

Using a Separate AmplifierChannel for the 12.1In certain specialized applications, it maybe desirable to drive the subwoofer with aseparate amplifier channel. In theseapplications the active crossover pointmust be at or below 160Hz so as not tointerfere with the built-in passive cross-over. Both sections (left and right inputs)must be connected in parallel (4 ohmsystem impedance) when operating as amono device. No load resistors arenecessary on the hi-pass outputs.

Characteristics of AllSubwoofersWhile subwoofers do radiate soundomnidirectionally (in all directions) and thesound is generally non-localizable (onecan't hear exactly where it comes from),subwoofer sound level still drops off thefarther one moves from the subwoofer.The highest output and best room loadingare accomplished with the subwoofermounted in a corner at a three-boundaryjunction (wall/wall/ceiling or wall/wall/floor,an arrangement also referred to as 1/8space). Mounting at a two-boundaryjunction (wall/ceiling, or 1/4 space)produces three dB less output, andmounting in the middle of a room in theceiling (1/2 space) reduces output stillanother three dB.Subwoofers produce large amounts oflong-wavelength low-frequency energy.Every object has its own resonantfrequency, and long wavelengths tend toexcite large objects (like walls, floors,doors and ceiling panels). Anything loosein or on a ceiling or wall will buzz or rattleas a subwoofer's level is increased. Mostof these can be isolated and fixed withsmall, strategically placed bits of foamtape. Others may require driving additionalnails or screws and perhaps somecaulking to dampen their sympatheticmovement. Be aware that as bass levelsincrease, so does the likelihood of rattlesand buzzes.


Appendix B: Painting the EVIDTM Speakers

The 12.1 subwoofer is a painted woodenclosure which can easily be repainted.

Painting Process(3.2, 4.2, 6.2)The EVID™ 3.2, 4.2 and 6.2 are made ofhigh-impact ABS, which accepts a widevariety of paints.• Remove the grille and mask the baffle.• Clean the cabinet and grille by rubbing

the speaker with a lightly dampenedcloth. Do not, however, use abrasivessuch as sandpaper or steel wool. Neveruse gasoline, kerosene, acetone, MEK,paint thinner, harsh detergents, or otherchemicals, as these agents may causepermanent damage to the enclosure.

• After cleaning, apply latex or enamelpaint. Spraying is recommended

Painting the Grille• Painting the grille requires spray

painting. If the grille is rolled or brushpainted, the mesh may become cloggedwith paint and poor sound quality mayresult.

Painting Process(12.1 Subwoofer)• Remove the four screws securing the

front hatch and lift off the hatch panel.Carefully twist and lift off the EV® logoand set it aside.

• The foam grille blocks are held in placeby sharp pins protruding through thebaffle board. Note the relative position ofthe foam and carefully lift the blocks offthe pins. Mask around the input panelwith tape and tape a piece of heavypaper over the woofer. It is not neces-sary to remove any components.

• Clean the cabinet, bracket and clips byrubbing with a lightly dampened cloth.Do not use abrasives such as sandpaperor steel wool. Never use gasoline,kerosene, acetone, MEK, paint thinner,harsh detergents, or other chemicals, asthese agents may cause permanentdamage to the enclosure.

• After cleaning, apply two or more twothin coats of either latex or oil-basedpaint. Spraying is recommended, but abrush and small roller work very well. Itis not necessary to paint all the way upto the woofer. Only the visible surfacesneed to be painted: the hatch front andside edges, the exposed enclosuresurfaces down to the hatch gaskets andabout halfway under where the foamblocks sit. Likewise, the back sides ofthe bracket and clips need not bepainted. The hatch screw heads may bepainted, if desired.

• When the paint is thoroughly dry,carefully unmask everything. Replacethe foam blocks, pressing them gentlydown onto the sharp pins. Replace thehatch cover and tighten the four screws.Locate the small center hole, properlyorient the EV® logo, and press it firmlyinto place at its center to reseat it in themounting hole.


Appendix C: Troubleshooting Table

melborP sesuaCelbissoP noitcA

dnuoSoN

reifilpmA

reifilpmaehtotrekaepstsetgnikrownwonkatcennoCscinortcelellatahtkcehc,dnuosonsierehtfI.stuptuo

siecruoseht,tcerrocsignituorlangiseht,noera.noosdna,pudenrutsiemuloveht,evitca

sierehtfI.yrassecensaecalpeR/riapeR/tcerroC.gniriwehtnisimelborpeht,dnuos

gniriW

sriaperiwtcerrocehtdetcennocevahuoytahtyfireVhguorhtlevelwoltagnihtemosyalP.reifilpmaehtot

.)renutroreyalpDCamorf,elpmaxerof(reifilpmaehtehthtiwlellarapnirekaepstsetehttcennoC

siroenogsahdnuosehtehtfI.enilgninoitcnuflamerevesaylbissop(tinitrohsasahenileht,kaewyrev

sileveldnuosehtfI.)erutcnupelpatsro,hcnip,eparcsdessimroeriwtucaylbissop(neposieriwehtlamron

ehtnwodevom,rekaepstsetehtgnisU.)noitcennocehtdnifuoylitnunoitcnuj/noitcennochcaetsetdnaenil

.ytiralopreporpevresbO.titcerrocdnamelborp

tsetehtesu,refoowbus1.21ehtgnisuerauoyfIstuptuodnastupniehtevahuoytahtyfirevotrekaepstupnirefoowbusehtfI.seriwtcerrocehtotdetcennoc

onroelttileblliwereht,deriwyltcerroctonsilenap.ytiralopreporpevresbO.dnuos

-woLrooPycneuqerFesnopseR

deriWsrekaepSytiraloP-fo-tuO

tuo(ytiralopfotuodetcennocerasrekaepsowtnehWrehtohcaelecnaclliwseicneuqerfwoleht,)esahpforosgnikrameriwehtevresboylluferaC.yllacitsuoca

reifilpmaehttahtyfireV.seriwrekaepsruoynosrecartslanimretrekaepsderehtotdetcennocsilanimret)+(kcalbehtotdetcennocsilanimret)-(reifilpmaehtdna

.slanimretrekaeps

deriWylreporpmIlenaPrefoowbuS

llatahtyfirev,evobadebircsedsarekaepstsetagnisUriehtotdetcennoceraseriwrekaepsdnareifilpma

gnisreveR.ytiraloptcerrocehthtiwslanimretreporpssabllatuotucnacseriwreifilpmafotesenotsuj

.refoowbusehtmorftuptuo

tuptuOtnettimretnIgnilkcarCsahcus

noitrotsiDronoitcennoCytluaF

otsrekaepsdnareifilpmatasnoitcennocllakcehCmelborpehtfI.thgitdnanaelcerayehterusne

rehtoeeS.gniriwroreifilpmaehtniebyamti,stsisrep.evobasnoitca

esioNtnatsnoC,gnizzuBsahcusgnimmuH,gnissiH

reifilpmAevitcefeDcinortcelErehtoro

eciveD

silairetammargorpontubtneserpsiesionehtfIehtniniahclangisehtsiesuacylekileht,gniyalp

yrassecensatnenopmochcaeetaulavE.scinortcele.melborpehtetalosiot

metsySrooPrognidnuorGpooLdnuorG

.deriuqersa,gnidnuorgmetsysehttcerrocdnakcehC

ecioV-ortcelEtseraenruoytcatnoc,melborpruoysevloswolebsnoitseggusehtfoenonfI.rotubirtsidecioV-ortcelEroretnececivres


Appendix D: Technical Specifications

Specification 3.2/3.2t 4.2/4.2tFrequency Response1 85 Hz-20 kHz 65 Hz-20 kHz(-10 dB)

Power Handling2 150 watts 200 watts

Sensitivity3 87 dB, 1 W/1 m 90 dB, 1 W/1 m

Impedance 8 ohms 8 ohms

Max SPL 104 dB 111 dB

Horizontal Coverage4 120° 100°

Vertical Coverage4 110° 90°

LF Transducer 2 × 3.5" (90 mm) 2 × 4" (90 mm)

HF Transducer .75" (20 mm) 1" (25 mm)

Protection Full System Full System

Suspension/ Multi-Axis Multi-AxisSwing × Rotation 100° × 45° 100° × 45°

Terminals 4-Pin Phoenix-Style 4-Pin Phoenix-StylePlug-In Connector Plug-In Connector

Enclosure Material ABS (paintable) ABS (paintable)

"t"-version wattage taps 5 W 70 V/10 W 100 V 70 V: 3.25 W70 V/100 V: 7.5 W, 15 W, 30 W,8 ohm Bypass

Dimensions 9.2" × 5.1" × 6.5" 12.2" × 6.9" × 8.5"234 × 127 × 165 mm 310 × 175 × 216 mm

Net Weight (each) 3.3 lbs (1.5 kg) 8.5 (3.9 kg)

Shipping Weight (pair) 8.6 lbs (3.9 kg) 19 lbs (8.6 kg)

Included Accessories SAM, hex key SAM, hex key

1 Half space (wall mounting)2 Long Term Program Rating, 3 dB greater than continuous noise pink noise rating3 Avg. Half Space (wall mounting)4 When mounting with long axis in vertical plane


Appendix D: Technical Specifications

Specification 6.2/6.2t 12.1Frequency Response1 62 Hz-20 kHz 40 Hz-140 Hz(-10 dB)

Power Handling2 300 watts 175/175 watts

Sensitivity3 95 dB, 1 W/1 m 100 dB, 1 W/1 m

Impedance 8 ohms 8 ohms

Max SPL 116 dB 122 dB

Horizontal Coverage4 100° N/A

Vertical Coverage4 90° N/A

LF Transducer 2 × 6" (90 mm) 12" (90 mm) high-excursiondual voice coil

HF Transducer 1" (25 mm) N/A

Protection Full System N/A

Suspension/ Multi-Axis N/ASwing × Rotation 100° × 45° N/A

Terminals 4-Pin Phoenix-Style SpringPlug-In Connector

Enclosure Material ABS (paintable) MDF (steel fastener reinforced)

"t"-version wattage taps 70 V: 7.5 W N/A70 V/100 V: 15 W,30 W, 60 W, 8 ohm Bypass

Dimensions 16.5" × 9" × 11.75" 16.25" × 23" × 12"419 × 228 × 298 mm 412 × 584 × 305 mm

Net Weight (each) 12 lbs (5.3 kg) 40 lbs (18.1 kg)

Shipping Weight (pair) 27 lbs (12.3 kg) 48 lbs (20.0 kg)

Included Accessories SAM, hex key Mounting brackets, hardware

1 Half space (wall mounting)2 Long Term Program Rating, 3 dB greater than continuous noise pink noise rating3 Avg. Half Space (wall mounting)4 When mounting with long axis in vertical plane

17EVIDTM Owner’s Manual

Notes

U.S.A. and Canada only. For customer orders,contact the Customer Service department at

800/392-3497 Fax: 800/955-6831Europe, Africa and Middle East only. For customer orders,

contact the Customer Service department at49 9421-706 0 Fax: 49 9421-706 265

For warranty information, contact the Service Repair department at:616/695-6831 or 800/685-2606

For technical assistance, contact Technical Support at:866/78AUDIO

Specifications subject to change without notice.

12000 Portland Avenue SouthBurnsville, MN 55337Phone: 952/884-4051Fax: 952/884-0043

www.electrovoice.com© Telex Communications, Inc. 5/2007

Part Number 38109-899 Rev C

Documents

EVID Owner's Manual 909 KB